Onedrous Integrated Toilet and Bidet
Contents
1. User manual covers the installation of the bidet toilet seat in box labeled 2 of 2 and the toilet in box labeled 1 of 2 To view installation video scan QR code with mobile device This user manual contains the products warranty Please submit to our warranty department within 15 days of purchase Product Features Front Wash For her front wash Back Wash For his and her back wash Turbo wash Oscillating water stream Dry Warm air dryer Oscillating Adjustable nozzle moves back and forth to wash _ Continuous Adjustable water temperature 4 levels _ Seat temperature control Adjustable seat temperature 4 levels Dryer temperature control Adjustable air dryer temperature 5 levels Automatic Self Cleansing Stainless Nozzle Nozzle contains a stainless cap to prevent debris Nozzle is automatically washed before _ and after each use Deodorizer 2600060000 To remove odor from toilet bowl VOOBDOS eO 6 Auto flush Automatically flushes toilet Sleep mode _ Minimize electricity consumption when not in use Protection from low temperature burn Protect user from low temperature burn Protection from electrical short If short in electrical special breaker cuts the power Antibacterial resin _ Antibacterial resin for nozzle seat and seat cover Manual Control Manual control on main unit in lieu of remote control _Self2. or dryer function will stop Installation Manual and Operating Instructions ROYAL uolje1adO Operation Basic m Sit on the seat l Please make sure that your skin is in direct contact with the skin sensor a when sitting on the seat to fully activate om m m mm Reference Do not press the control buttons remote control single controls harder than needed This can cause damage Please be aware to pull down your clothes amply and do not cover the seat with any clothing items as it can prevent the seat from activating m Push Front wash Back wash or Turbo wash button Each function runs for approximately 2 minutes Reference Front wash Back wash or Turbo wash stops automatically after 2 minutes For additional use press function again Front wash and Back wash button are located on the front of the remote control m Push the dry button l The dryer function operates for approximately 3 minutes When the dryer button is pushed the auto flush function works automatically Reference When dryer function is selected deodorization stops After dryer function stops deodorization starts again Normal operational conditions m Push the auto flush button li Push the auto flush button on remote control to operate auto flush function By pushing the button for 3 seconds the auto flush function will change to manual flush m Push the Stop but
3. Diagnosis Automatically runs diagnostic Soft opening and closing Seat cover and seat opens and closes slowly Water filters Improves hygiene by filtering out contaminates from tap water Contents Preparation Installation Operation Other ROYAL LINE Proctict teatres a oea R A E E OAE 2 important sateguards e eee e tr eeeeeerere 4 Cautions Before Installation s s s s sesssssesececeeesseseseseeeees 4 General Caution ea A a AES eres 6 Prod uct components o eae et eee er 10 Setting up and using the auto flush s 12 Setting up and using the remote control vesesereress 14 Initial operation Me ccamean E EE sae cer E E one 15 Checklist before Use ec eee ee 16 HOW EO USES UNINA E E EE enertrie cers 17 Operation Basi cee ces eee ee iaaa aE rice 18 Operation Detal Ia a e E mien 22 Separation of the unit from toilet bowl cceeeeseees 26 Draining water from tank eee e 27 Maintenance for winter season sesesseseesesseseeccceseeseseenees 27 Trouble shooting DOR T TE Pe RENTAL Es RAR T AR aOR RCC ESR E 28 Specifications ct ere teeter cetert er 29 IMFONIMTIATION to thesen eset cee eee ace 30 Warranty oe harmon nen acie teem ern 30 Installation Manual and Operating Instructions uoljeiedald Ho Sa OQ oF gt uoj e e su IMPORTANT SAFEGUARDS Cautions Before Installation A READ ALL INSTRUCTIONS BEFORE INSTALLATION AND USE WIRING REQUIREMENT
4. Push water high or low button to set dry temperature Air Dryer temperature can be adjusted by 5 levels water orver J etme ter pressue Air dryer temp i s z Installation Manual and Operating Instructions Ho D a Q oF O gt ch Operation Detail m Water pressure control I Push water pressure dry temperature High or Low to set water pressure from 1 to 5 levels Water pressure which was previously set is saved Push High or Low button to set water pressure a Oter pressu amp Air dryer temp a NOTE If the water pressure is weak Check if the water pressure is set to low m Water temperature control A Press the water temperature button and LED display will change so you can select your eral desired water temperature You can set the water temperature while using water Brea water temperature dp Low High m m m m Low High Low High Low High Low High Room temperature off 93 2 F 98 6 F 104 F m Massage i During the Front wash Back wash or Turbo wash function push the Turbo wash Massage button to start the Massage function When massage function is working push the turbo massage button to stop the function Auto massage function The massage function is automatically activated when using each wash function Front Back
5. Trouble shooting Factors to check Specification TH 0111 Power rating 120V 60Hz 1400W l nae Type Direct inlet Flow Type Low Tank Check if the water tank is filled l ae l The water does not spray See if the water valve is open Mtii Water inlet pressure 1 0 7 0 kgf am 14 2psi 99 6 psi Check if the water filter strainer is clogged Max 700cc 150cc min Max 700cc 150cc min Check if the power cord is connected Water pressure adjustments 1 5 levels a See if the power is turned off from the main unit Wash devi The unit is not operatin eee p g Make sure that the Skin sensor on the seat touches your skin when Warm water temperature Room Temp 93 2 F 98 6 F 104 F you sit on the seat control i i on Water is leakin Ensure plumbing is properly connected If water is leaking from the main unit EN PAEA ETAS cone ae g disconnect and contact service personnel rr Temperature control Room Temp 93 2 F 98 6 F 104 F w Seat i Safety device Thermal fuse temperature sensor in seat Prevent low temp burning Water pressure is weak Check if the water pressure Is set to low Room temp 113 F 5 levels Warm Air 00 Dryer Device Safety device Thermal fuse Seat water and See if seat temperature is set to low Se Turbo wash function O See if the water temperature is set to low ELB 7 dryer is not warm mO See if the dryer temperature is set to low Economy mode O Deodorizer O When the
6. for 3 seconds the function is cancelled After setting deodorizer function it is automatically activated when sensing person Deodorizer button Deodonzer button Press 3 4 Press 3 4 Select Single Chime Q a ee C P Cancel Double Chime amp Single chime a Double chime Deodorizer function automatically stops after approximately 1 minute Reference Deodorizer function stops while dryer is selected After dryer function completes deodorizer automatically activates ROYAL LINE m Battery Replacement If LED light on main unit does not go on when pressing button on the remote control change battery LED light turns on with initial push of desired button press again to activate function After 10 minutes unit goes into energy saver mode You will need to reset functions after changing batteries Be careful polarity 1 1 real size 1 5V Alkaline AAA battery Please insert batteries into remote Closed battery cover Replace batteries Z m Change batteries when LED is flashing PA A Installation Manual and Operating Instructions Ho D Sa Q oF O gt 19 Draining water from tank Loosen the nut on the hose that is connected to the unit and then separate the electronic toilet seat from the toilet in the following order as illustrated a Disconnect the power plug 2 Shut the valve by turning it to the right JN Do not t
7. immediately hazardous situation A N Caution Indicates potentially hazardous situation and if not avoided may result in minor or moderate injury or damage to the unit Prohibited Emphasis on what not to do Instructions How to operate and install unit A Safety Warning S Do not plug in the power cord before connecting Do not plug in the power cord before connecting the water supply hose the water supply hose May result in fire or damage to the unit This product is only for 120V AN This unit requires a dedicated outlet oxidized products sink products toilet cleaning products and any type of stain remover on the external surface of the electronic toilet seat Also do not spray air fresheners onto dryer seat as the unit has a deodorizer Children elderly patients and those who When cleaning the product do not use detergent are physically limited should use the low temperature setting for the seat water and After using the unit at high temperatures the temperature should be readjusted to Low for the elderly children and those with o A sensitive skin produ ml products products Using cleaning detergents or air fresheners can change the color of the external Surface and can also cause problems with function of the seat Connect the product to cold water supply Q The product must be connected to a 120V power source Do not plug the unit into a loose electrical outlet M
8. nozzle doesn t i i ae Inlet water temperature 41 F 93 2 F recommended 54 F 93 2 F ee Make sure skin is touching Skin sensor Renee OE ne Dimensions W 415mm 16 34inch L 695mm 27 36inch H 145mm 5 71 inch Weight 43 74kg 96 43 lbs China bowl 38kq 83 78lbs Bidet 5 74kg 12 66lbs When water is cold or warm Adjust the temperature Recommended water pressure is 1 0 7 0 kgf cm Body unit shakes Tighten the bolts do not over tighten Dryer does not work Make sure skin is in contact with skin sensor Installation Manual and Operating Instructions 29 Information to the user This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one more of the following measures Reorient or relocate the receiving antenna Increase the distance
9. or Turbo wash How to set auto massage function After using each wash function Front Back or Turbo wash push stop button and then push massage button Hold for 3 seconds to set massage level Unit will beep when set Push the button again for 3 seconds to cancel massage setting Unit will beep twice when cancelled After auto massage function is set for each wash function Front wash Back wash or Turbo wash massage function will be operated automatically during each function even If user did not put the massage button waseige Hold for 3 seconds to set josse Hold for 3 seconds to cancel massage When selected Beep massage level O setting Unit will Beep twice when when canceled Beep beep Unit will Beep when set N deactivated E Oscillating Oscillating O Ho a D 2 Fa H ok O gt Auto oscillation function Even if user does not push oscillation button when user uses each wash function Front wash Back wash or Turbo wash oscillation is set to operate automatically How to set or cancel the automatic oscillation function After using each wash function Front wash Back wash or Turbo wash push stop button and then push oscillate button for 3 seconds then auto oscillate function will be set up with beep sound Push the button one more time for 3 seconds and it will cancel the oscillation function Unit will beep twice when cancelled After auto oscillatio
10. or not be supplied When the following people sit down on the seat a guardian should pay extra attention so that they will not fall when sitting may cause damage to the soft closing feature S Do not use a broken product Prevent children from putting foreign substances or inserting their hand into the dryer outlet or onto the nozzle Can cause burns Can cause product failure Constant direct sunlight may cause discoloration of unit May cause discoloration on the toilet seat or standing up from it Children elderly or those who cannot independently sit or stand on the seat D 9S ROYAL LINE A N General caution Never put the product in water May cause electric shock or damage the product A guardian should be present when the seat is in use by a child May cause Injury Do not let urine contact the dryer outlet or nozzle area May cause failure If nozzle is clogged please clean with a soft brush When cleaning power cord please clean with dry cloth Do not push the control button if not using the product control When cleaning or not using the product over a long period of time be sure to unplug the unit Refer to page 27 May cause electric shock Sitting on seat or using dryer for a long time may cause low temperature burns Those who cannot adjust the temperature or those who hav
11. then water will begin to flow into unit FLUSH OCCUPIED ENERGY SAVER eA 4 While sitting on the unit please check each function by following user manual This product only works when user sits on the seat Please be aware that your skin must be in contact with the skin sensor to initiate functions When the seat LED turns off RF type remote control and main unit are synchronized Be a Installation Manual and Operating Instructions Checklist before use 4 Only use a grounded 120V 60Hz outlet for this unit To operate properly this product needs to be plugged in Checklist after installation 2 Open the water valve and determine if there are any leaks To operate properly water has to be supplied 3 Please sit on center of seat If baby seat is installed on seat the product will not operate properly Skin sensor will not detect baby seat Before use of this product please remove the skin sensor sticker 4 If water pressure is weak During flushing water pressure may be slightly diminished You may experience delayed nominal nozzle function if water pressure is low 5 Cleaning the body unit Beware not to use any bathroom cleaning detergents such as benzene acid chemical detergent on the seat exterior Using any type of chemical products or rough scrubbers on the electronic toilet seat surface which is made out of plastic material can either damage or change its color
12. your warranty protections you must complete and return this card SEND with a copy of your receipt to Royal Line within 15 days after date of TO purchase to validate your warranty Model Serial Number Purchaser Company Address Zip code City Country Phone Fax Dealer Company Dealer Code Address The serial number is located in the lid of the unit Attn Warranty Dept Royal Line LLC PO BOX 1313 Seaford NY 11783 Service Department Inquiries and support Email customerservice royallinellc com Phone 800 516 7450 Installation Manual and Operating Instructions
13. AL SCREW Grounding Screw A OUTLET BOX B C 5 Never block the air openings of the product or place it on a soft surface such as a bed or couch i Figure 1 where the air openings may be blocked Keep the air openings free of lint hair and the like 6 Do not use the unit if you are sleeping or tired to the point of being drowsy 7 Never drop or insert any object into any opening or hose Improper grounding can result in electric shock Electric wiring has to be done 8 Do not use outdoors or operate where aerosol spray or oxidated products are being used j spray P J A D ANGER in accordance with all local codes or in the absence of local codes 9 Unplug this product before filling Fill reservoir with water Do not overfill or specify filling instructions with National Electrical Codes The use of an extension cord is not recommended or advised If it is necessary to use an extension cord use only a three prong extension cord one to one and a three slot built in GFCI receptacle that will accept the plug for this product The marked rating of the SAVE THESE INSTRUCTIONS extension cord should be equal to or greater than the electrical rating of the unit 10amp Consult a licensed electrician if you are not sure whether it is properly grounded Installation Manual and Operating Instructions 49 General Cautions The following terms are used in this manual to indicate hazards A Da nger Indicates an
14. Do not spray water directly or use a shower hose on the main body unit Can cause fire or damage to the unit When cleaning the power cord must be unplugged from the power outlet and make sure water does not contact the cord and or outlet After cleaning use a soft cloth to dry the unit JN Do not use any cleaning products such as Oxy Clean How to use Summary LINE If skin sensor is not working the control button may not work 4 Sit on the seat If user s skin is not in direct contact with the skin sensor If baby seat is installed on the product Please have full contact with the skin sensor when sitting on the seat If the skin sensor cannot detect the skin back wash front wash turbo wash and or dryer function may not work Push front wash back wash or turbo wash button Can use front wash back wash or turbo wash functions Each function operates for approximately 2 minutes and stops automatically Push the button again for continued use Push the dryer button Dryer function operates while the LED light water pressure dry temperature on remote control is on The dryer function works approximately 3 minutes and stops automatically Push the dryer button again for more drying Push the auto flush button Change auto flush to manual flush by holding button for 3 seconds 5 Push the stop button All functions will immediately stop Back wash turbo wash front wash
15. R To reduce the risk of electrocution This unit is for use with a 120V circuit and has a grounding plug see sketch A in Figure 1 If a properly grounded 1 Do not place or store product where it can fall or be pulled into a tub or sink a outlet is not available a temporary adapter see sketch B and C may be used to connect plug to a 2 pole 2 Do not place in or drop into water or other liquid receptacle The temporary adapter should be plugged into a properly grounded outlet sketch A and should be 3 If unit falls into water unplug unit and remove trom water Ei o installed by a licensed electrician The green colored rigid ear and lug extending from the adapter must be connected to a permanent ground A N CAUTION To reduce the risk of burns electrocution fire or injury to persons 1 Close supervision is necessary when this unit is used by children elderly or disabled 2 Use this product only for its intended use as described in this manual AEE Ait ONEEN LEMP Ora Connection Do not use attachments not recommended by the manufacturer ee GROUNDED 3 Never operate this product if it has a damaged cord or plug or if it is not working properly OUTLET ADAPTER 29 A N jer ADAPTER if tt has been dropped or damaged or dropped into water Return the product to a service center for examination and repair TAB for GROUNDING PIN l 4 Keep the cord away from heated surfaces GROUNDED MET
16. THIS PRODUCT MUST BE PLUGGED into a 120V grounded GFCI outlet North America 120V ac 60HZ The rated power consumption is 1400W In locations where only a standard two prong outlet is available it is the responsibility of the user to install a grounded The following terms are used in this manual to indicate hazards three prong outlet Using high voltage is dangerous and may result in a fire other accident or damage to the unit Manufacturer is not responsible for damage resulting from high voltage or operating without proper grounding A Da nger Indicates an immediately hazardous situation This product should be on its own circuit Sharing a circuit could cause the A N CAUTION branch circuit fuse to blow or the circuit breaker to trip Continuous usage Indicates potentially hazardous situation and if not avoided may result in minor or AN Caution y y moderate injury or damage to the unit i ae under these conditions may result in fire or damage to the unit o Bo ks ae O TA R a D oF O 33 Q Prohibited Emphasis on what not to do Instructions How to operate and install unit GROUND INSTRUCTIONS This appliance has to be grounded This unit must be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock This unit is equipped with a cord having a grounding wire with a grounding plug The plug must be plugged into an outlet that is properly grounded A DANGE
17. ay cause fire or electric shock A Do not separate disassemble or repair the unit RG Do not connect power cord if the cord is damaged or broken ROYAL LINE A Safety Warning Do not splash water on the main unit or power cord and do not utilize it in areas of or allow foreign substances inside the unit oN high levels of humidity Only qualified service personnel should repair this product and plugged into an AC120V 60Hz power wet hands outlet Please ground to prevent from electric shock This product must be grounded before usage N Do not plug or unplug the power cord with It can cause electric shock or bodily injury Keep the cord away from flammable substances May cause an electric shock or damage to the unit if not properly grounded Unplug the power cord when cleaning the product Turn off power to outlet prior to installing unit May cause failure or electric shock Installation Manual and Operating Instructions ar La fog a O O O 2o OQ oh O Te 49 General Cautions A N General caution Do not stand on seat or seat cover Do not sit on closed seat cover Do not stand on top of the seat cover seat or main body unit This can damage or break the unit Do not slam or close the seat cover forcefully O Can damage the product Do not pull the connecting hose forcefully or bend it Water may leak
18. between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING Any changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment and limited warranty Warranty ONE YEAR WARRANTY VALID ONLY WITH ORIGINAL PURCHASE RECEIPT Warranty Royal Line LLC warrants this product against defects in any parts or workmanship for a period of 1 year from the original purchase date This product is for residential use only It is not intended to be used in commercial or industrial settings This product warranty covers only the original consumer purchaser of the product Warranty Coverage This warranty is void if the product has been damaged by accident neglect improper handling or operation shipping damage abuse misuse unauthorized repairs made or attempted alterations improper assembly installation or maintenance commercial use or other causes no arising out of defect in materials or workmanship This warranty does not extend to any units which have been altered or modified or to damage to product or parts there of which have had the serial numbers removed altered defaced or rendered illegible Implied Warranties Any implied warranties which the purchaser may have are limited in duration to 1 year from the date of purc
19. e sensitive skin should take special precautions Installation Manual and Operating Instructions fog a a O 2o OQ oh o D A Product Components UNE E Main unit Back wash E Remote control PD uoljeiedald Turbo wash Remote control Nozzle wash Energy saver Water pressure Water Seat Massage Qscillate Deodorizer Nozzle Position Air dryer temp temp temp Lid Caution label Front wash Remote control front eran SEAT OOO water J 0 0 water prver 0 O Remote control receiver Main function Power plug Main unit s Stop all operation lt Turbo wash Nozzle Manual Flush refer above DRY l Back wash Dry washed area Simple Control Skin sensor embedded in seat FRONT Fee Water supply hose Heated Seat we Front wash Flush the toilet for bidet amp ee Toilet bowl eve ranch Water supply hose ra runction for toilet flush water tank y When selected during wash function it starts massage wash m To stop function push the button one more time Nozzle ities pesenaa nr ane eereneas ie When selected during wash function nozzle oscillates automatically for wash a wider wash To stop oscillating function push the button again Energy With automatic energy function the seat temperature will stay at 89 6 F If no one is using bidet it returns to sleep mode saver The automatic sleep mode can be adjusted by pressing energy safe but
20. hase This limited warranty is in lieu of all other warranties expressed or implied including warranties or merchantability and fitness for a particular purpose and excludes all liability for incidental or consequential damages for any cause whatsoever Warranty Performance During the above 1 year warranty period a product with a defect will be replaced when the product is returned to an authorized dealer The replacement part will be in warranty for the balance of the 1 year period and an additional one month period No charge will be made for such replacement This Warranty does not cover the following 1 Defects and or malfunctions from failure to properly install operate and or maintain the unit in accordance with the installation manual Damage from abuse fire flood freeze and any other acts of nature Damage resulting from unauthorized alterations attachments and or repairs Damage to the unit by animals mice or insects Damage caused by excess moisture or from water flooding the bathroom 2 3 4 If the product was not installed properly 5 6 7 Damage from not being installed in accordance with all applicable local codes ordinances and good trade practices 8 Color fading due to use in wrong environment 9 Damage from exposure to chemicals and cleaners 10 The warranty will not be covered without providing the date of purchase with original receipt WARRANTY REGISTRATION PLEASE To ensure
21. l please push the same button on the remote control one more time and push the oscillate or massage button m Automatic self cleaning nozzle function i Without sitting on the seat water flows automatically Nozzle moves for about 20 seconds to wash entire nozzle and then automatically retracts shes tye ae Oscillat m O xX Li ROYAL LINE m Seat temperature control l f seat temperature button is selected LED display will show selected temperature seat temperature daD D D 0D Low High Low High Room temperature off Reference Please close the seat cover when the product is not used It will keep seat warm and save electricity Low temperature safe mode Low High Low High Low High 93 2 F 98 6 F 104 F After 15 minutes sitting on the seat maximum seat temperature will be reduced gradually in 5 minute increments for 30 minutes E Nozzle position control l To set the nozzle position please push the nozzle position button back or front while using front wash back wash or turbo wash Nozzle position which was previously set is saved Nozzle position can be adjusted by 5 levels warer orver 0 0 000 T on a e 1 Nozzle Positiorw N m Air Dryer temperature control l Push water pressure dryer temperature High or Low to set air dryer temperature Dryer temperature which was previously set is saved
22. n function is set for each wash function Front wash Back wash or Turbo wash oscillation function will operate automatically during each function even if user did not push the oscillation button ee Hold for 3 seconds to set Oscillate Nozzle wash Hold for 3 seconds to cancel Oscillate When selected Beep when canceled Beep beep Even if the power is out or reboot it auto move function setting will remain auto oscillation level and oscillation setting unit will Beep when set Beep beep will sound Installation Manual and Operating Instructions 8 sy 11 Operation Detail m Energy saver e e OFF ON Flashing m Saver On Off State State State When pressing the energy saver LED on the main unit will turn on Energy saver mode automatically maintains water and seat temperature of 89 6 F 32 C OCCUPIED ENERGY SAVER POWER In energy saver mode the seat heating temperature could appear to be lower than the actual temperature setting Other energy saver tips In order to save energy please abide by the following instructions Keep seat cover closed when not in use to prevent heat from being lost Keep temperature set to low Please unplug the power cord if you do not plan to use the unit for a long period of time E Deodorizer m Deodorizer ON Off initial setting is Off Please press button for 3 seconds press button again
23. n on slim key side button seat unoccupied for about 3 seconds the ball chain will begin turning 3 Insert ball chain to the ball chain connector as photo below X Make sure that the ball chain is inserted properly and place the bidet on the toilet bowl X After checking ball chain place the bidet on the toilet bowl 4 After installing from mounting bolts 5 and rear mounting bolts 6 Mounting bolt en press Front wash button on slim key for about 3 seconds to initialize Bolt case Base plate Toilet mounting holes Mounting packing Mounting Nut Front wash button U aa D O J 8 Connect the flexible tube Connect the flexible tube with T valve and turn water supply valve to allow water to flow Installing rear mounting bolts e Please turn mounting bolts gently with hand Do not use power tools or driver _ water inlet hose water inlet hose for toilet bow ___Rubber cap ffor bidet Mounting bolts Too long X Suitable O Too short X Adjust the length of ball chain by examining the functioning state of plug lt gt N SS water supply valve eee eee Qu ee eres er es seers esses sss a e e e e e e e e mm m o e e ee ee ee ee ee ee ee ee eee ee ee eee ee 2 Make sure there is no water leakage Do not use power tools or screw driver the ball chain to toilet lever and siphon cover Installation Manual and Operati
24. ng Instructions B Setting up and using the remote control Initial operation ROYA m Setting up remote control l Remote control holder should be installed in an area that will not be exposed to water Turn to the left to open the inlet valve and check to make sure there are no leaks in the hose connection Make sure that the selected spot will not be exposed to water and the area where you intend to affix the holder is clean and dry Place remote control holder in convenient spot near the toilet bowl Place 2 AAA type batteries into remote control Please consider the right polarity for toilet flush water tank Z Back side of double sided tape D it i Skin sensor water supply hose l for bidet 7 A oF water supply hose D O e water supply valve m Initial setting for RF transmission remote control a OFF ON Flashi Without sitting on the unit push and hold the top and front wash button for 5 seconds on the Gaps Ge ce simple control until the seat LED turns on 2 Connect power plug to 120V outlet If LED light is not working after plugging in outlet push the back wash or front wash button on the simple control FLUSH Remember this control pad is located on the side of the bidet top It will make beep sound if water begins to flow into the unit 7 ENERGY SAVER Power l O OCCUPIED Push back wash or front wash Q
25. ton Back wash turbo wash front wash or dryer function will stop m Automatic self cleaning nozzle i Before and after any wash function the nozzle will automatically clean itself It is normal to see water spraying E How to clean the nozzle l Without sitting on the seat Push the ES Back wash button for 3 seconds on simple control side controls on seat The nozzle will come out and stop Brush the nozzle with a soft bristled brush After cleaning press the Stop button and the nozzle will perform tts self cleaning function Even if the stop button is not pushed nozzle cleaning function runs approximately for 2 minutes and will automatically stop m Nozzle Change l Nozzle Seperation Nozzle Combination A J a O O D Sa gt a D TOER O gt Installation Manual and Operating Instructions 19 Operation Basic E Manual Control l X Manual controls can be used if there is a power outage or remote control is damaged or lost Front wash Stop button button Manual controls include manual flush front wash back wash and stop button Manual flush Back wash power outages button button Water pressure and nozzle position of front and back wash can be adjusted by 5 levels Remote control cannot be used if front wash back wash oscillate or massage function are being operated manually To use oscillate or massage function after using simple contro
26. ton On Off Product components __ After user stands up trom seat it works approximately one more minute and then automatically turns off When the dryer function is Bae selected deodorization stops After dryer function stops deodorization starts again normal operational conditions Deodorizer starts again For plumbing For product fixation For remote control Installation instructions when user sits on the seat Water The water pressure and dryer temperature Nozzle The nozzle position can be adjusted 5 levels Dryer can be adjusted 5 levels Position uJ o U h be adjusted h be adjusted 4 level The water temperature can be adjuste The seat temperature can be adjusted 4 levels T valve Front packing and bolt 2pcs Water seat f p J 2pcs 4 levels off low middle high and can be off low middle high and can be checked by LED light OO ee Remote control 1 5v AAA type checked by LED light Water supply hose Holder Battery 2pcs for toilet flush water tank Side packing and bolt 2pcs User manual Quick Guide Installation Manual and Operating Instructions g Setting up bidet onto toilet and using the auto flush INE X Bidet and contents can be found in box labeled 2 of 2 4 Install base plate 2 Fixed hinge install 5 Connecting water flush ball chain 6 Installing front mounting bolts Please make sure to tighten bolts and nuts o 1 Plug in power and unit will beep 2 Press Front wash butto
27. urn the seat upside down This can cause damage to the unit as well as fire hazard X Raise main unit of bidet after separated Fix Cap arrow indicated amp fixed bolt 5 Disconnect the T valve from the water supply Refer to page 13 6 Separate bidet after disconnecting bidet and toilet hose Connect the water hose to the toilet which was disassembled while installing the electronic toilet seat and turn the water valve to the left to open it See if there is any leaking from the water hose connection 13 Separation of unit from the toilet bowl F F Maintenance for winter season Please follow the instructions below when moving or separating the unit from the toilet for cleaning purposes Ho o gt a Q or O gt 4 Check if the power cord is plugged in securely FIUSH power is connected led is lighten OCCUPIED ENERGY SAVER 4 Disconnect the power plug POWER Adjust the Fii button to low to prevent water Gag from freezing 2 Shut the water supply valve 3 If the product is not used for a long period of time please disconnect the power cord and drain the water from the internal unit 3 Push and hold the drain button in the center of the bidet top to completely drain the water from the internal unit 228 _ Installation Manual and Operating Instructions Specifications ova 15 Trouble shooting X Please be sure to check the following aspects before asking for help
Download Pdf Manuals
Related Search