RC T2020 - RC Electronics
Contents
1. 3 Initial release of user manual RC T2020 Telemetry system Page 132. ED is off Note Although the unit has sophisticated charger it is strongly advised to disconnect the USB cable when charging is complete This way the battery lifespan will remain longer and the battery healthier It is also important to check the unit s battery and recharge it if needed If battery gets discharged too much it may become unusable In such case the unit must be sent to service center for battery replacement Firmware update e Download the latest firmware for the RC T2020 unit from our web site Firmware should start with name RC T2020 vXXX bin XXX is version number 101 means v1 01 e Connect the unit with a USB A to mini B cable to PC e Press right OFF button and hold it pressed When OFF button is pressed press and hold down left ON button See figure 6 e You can release OFF button but ON button must be held pressed until the end of the firmware update e Wait for around 15 s and new disk drive figure 7 will appear with firmware bin file on it e Delete firmware bin file and copy latest firmware file to this disk drive e When you see new FW file on this disk you release the ON button and update is finished e Turn ON device and update is finished RC T2020 Telemetry system Page 12 RIGHT OFF Button Right Left Enter ON RC T2020 ANRC Ki Electronics www rc electronics org Figure 7 New disk drive Figure 6 Left and Right buttons Revision history January 201
3. EFT RIGHT al or p Set Multi 2 channel 1 to 69 Set altitude cut off from 30 to 900m in 5m Steps Or set to OFF Set motor run time from 5 to 120 seconds in 1 sec steps Or set to OFF Send new settings to RC Multi 2 module Request sent waiting for confirmation OR Confirmation received new settings sent to RC Multi 2 Page 10 Error check for communication between modules and try again LEFT RIGHT Exit Multi 2 settings menu LEFT RIGHT Exit Settings menu Note 1 To make value changes where available press Enter Arrows appear on both sides of the value Set the desired value using Left and Right buttons and confirm with Enter Note 2 If there is no RF link on the current channel related values will be replaced by dashes With no unit connected and no user interaction the RC T2020 will turn off after 2 minutes battery saver function RC T2020 Telemetry system Page 11 Turning the RC T2020 OFF To turn the RC T2020 unit OFF the RIGHT OFF button needs to be pressed for approximately 4 seconds Charging Charging of the RC T2020 is very simple and convenient as it can be charged using a common A to mini B USB cable Because of well designed built in charger there is no fear of overcharging the battery Upon charging the red LED near the mini USB connector on the bottom side of the RC T2020 housing is on When fully charged the L
4. RC 12020 Telemetry system Left Enter Right ON OFF RC T2020 A Electroni Electronics rc electronics org www Manual version 1 0 RC Electronics support rc electronics org http www rc electronics org Contents RCE GUCCI OW PETER 3 RO TS ia cscs Secs eet usu ei eue aDIIM EE LM MINIME UU c Pus d dM I CIIM 3 SPECON sioe eee UMS MEM MEUM M MEME RUE UM 3 PIUSIEgLDUBTVIB esce n RRVERERSSCHBENNRERNOKESERERIUREREAEMNKENI NI CEPI SSUENUEN RERO SEDNERIRPUXRANKIERSUNN MER REESE L aei MT H 4 BOLOM VEW ND t 4 Operating WS CIC COM anitcevecssacenasescesscsseeuce opecanvacweadosaanvansesseusaxenanceosessvanuecacweaneeneeevecesnvendess 5 ote guia dti 28 ON DA 040 Tr a E ae ee een ane re Oe ne eee 5 Menu amp functions OV BA ARS 5 WS ES RE 2020 OR E 12 TV NAS ER an sae eetow nt oseassauctdenctyessaiaenoadewn aces ceastacersseann oetonncoeetatenesnieece wiecesa emcees 12 Firmware update NR liue eem 12 Revision history RNRERem 13 RC T2020 Telemetry system Page 2 Introduction The RC T2020 was designed as telemetry system It can receive the data transmitted by RC Multi 2 RC TRX30 system It is a telemetry system to track current altitude maximum altitude flight duration with integrated manual stopwatch function climbing descending speed vario and battery status of RC Multi 2 RC TRX30 sy
5. imum altitude reached in current flight transmitted to RC T2020 LEFT i RIGHT Current climbing descending speed vario LEFT t RIGHT The RC Multi 2 module voltage LEFT RIGHT RC T2020 Telemetry system Page 5 LEFT 4 RIGHT LEFT i RIGHT LEFT fron LEFT RIGHT LEFT t RIGHT REE EN LEFT RIGHT LEFT RIGHT RC T2020 Telemetry system Ground speed the number displayed in the top right corner is the number of visible satellites Available only when option GPS data is set to yes Distance between power up point of Multi 2 unit and current position of T2020 unit first coordinate detected with number of satellites in use Available only when option GPS data is set to yes Trip made in current flight with number of satellites in use Available only when option GPS data is set to yes Geographic coordinate of the Multi 2 amp GPS unit latitude Available only when option GPS data is set to yes Geographic coordinate of the Multi 2 amp GPS unit longitude Available only when option GPS data is set to yes ENTER Manual timer press enter to start resume or to pause timer press enter and hold for 3 seconds then release to zero timer Page 6 LEFT V Set maximum flight altitude to zero RF link must be established In combination with RC GPS module also distance and trip are set to zero LEFT RIGHT Een Request sent waiting for confirma
6. stem transmitter and RC T2020 ground unit all in real time In combination with RC GPS module system can also track distance between units transmitter and ground unit trip distance and geographic coordinates All flight data is displayed on high contrast LCD display Key features e Altimeter e Variometer with climbing descending indication e Stopwatch e Two way data communication at 69 channels possibility to monitor multiple RC Multi 2 RC TRX30 systems e Long range more than 1 km e Simple charging from USB port no special charger needed e Strong and durable casing Specifications Unit Dimensions 65 mm x 42 mm x 17 mm LEM Nl Specifications are taken from component ratings and system limits and may not have been tested to the full extent of the specified ranges RC T2020 Telemetry system Page 3 Physical overview Front view 5 p LI sd RIGHT OFF Button LEFT ON Left Button ON Enter Right Ore RC T2020 ARC Electronics www rc electronics org Bottom view USB CHARGING SOCKET 3 5 JACK SOCKET CHARGING LED INDICATOR RC T2020 Telemetry system Page 4 Operating instruction Starting the RC T2020 Turn the RC T2020 ON by pressing the LEFT ON button On start up unit model and firmware version are shown for 1 second Menu amp functions overview Current altitude of the model is shown LEFT t RIGHT Max
7. tion or ERROR Confirmation received values set to zero OR Confirmation NOT received check communication between modules and try again Note Stopwatch is not affected by this function because it runs on the RC T2020 It will however reset to zero if the RC T2020 is restarted LEFT RIGHT settinss RC T2020 and RC Multi 2 settings ENTER RC T2020 Telemetry system Page 7 V ENTER Change the RC T2020 channel from 1 to 69 LEFT RIGHT Change the RC T2020 volume level LEFT i RIGHT Switch between metric and imperial units LEFT t RIGHT Make GPS data visible in the main menu You need RC GPS module for this function LEFT o RIGHT Voltage level of RC T2020 Hand unit not configurable LEFT t RIGHT Set values for altitude or battery warnings LEFT RIGHT ENTER RC T2020 Telemetry system Page 8 ENTER Set an altitude value to receive a warning sound if altitude is exceeded LEFT RIGHT Set the Multi 2 battery supply low warning level LEFT RIGHT Exit Warnings menu LEFT RIGHT Change the RC Multi 2 settings ENTER LEFT RIGHT Request sent waiting for confirmation OK amo OR Confirmation NOT received check for good communication between modules and try again RC T2020 Telemetry system Page 9 RC T2020 Telemetry system i ENTER LEFT m LEFT RIGHT LEFT RIGHT ENTER L
Download Pdf Manuals
Related Search