Series 90-30 DSM Module IC693DSM302-AF IPI, GFK
Contents
1. Configuration NOTEQ Not Equal When a rack configuration containing a DSM302 module is stored downloaded to an IC693 PLC CPU with a firmware revision earlier than 8 10 the MS DOS based programmer status area will still show CONFIG NOTEQ even though the store operation completes successfully If the configuration is immediately loaded back into the MS DOS programming software the status area will then show the expected CONFIG EQUAL The status area will continue to show the correct CONFIG EQUAL setting until a new configuration is again stored to the PLC CPU PLC Q Bits PLC Q bits are by design RETENTIVE in nature These bits ONLY become NON RETENTIVE after the location is used programmed in a PLC program All motion causing Q bits such as Drive Enable Start Motion program Jog etc must be controlled from a programmed PLC coil reference for safe operation Grounding Bars and Clamps The DSM302 for IC693 PLCs User s Manual describes the I O cable grounding requirements necessary for a system to meet CE Mark installation guidelines These guidelines include the use of grounding bars and clamps both of 4 Important Product Information C693 DSM302 Module GFK 1465E which are available from your distributor The Grounding Bar may be ordered as part number 44B295864 001R02 and the Ground Clamp as part number A99L 0035 0001 Cables Five different cables are available for use with the DSM302 as described below Consult the f2. errors D3 D9 to be reported incorrectly These firmware errors were fixed in version 1 20 Documentation Issues in DSM302 for C693 PLCs User s Manual Resolved by Revision A May 1998 Release The following table outlines the previously identified documentation issues that have been resolved by the revision A release of GFK 1464 DSM302 for IC693 PLCs User s Manual Issues Resolved by Revision A May 1998 Release Documentation Issue Description Resolution PCR Connectors Mislabeled Chapter 2 Two different connector pin configurations for the emergency stop JX5 in Pin Configuration connector on the B Series servo amplifier were shown with the labels Diagrams HIROSE and HONDA incorrectly reversed The labels were switched Grounding Bars and Clamps Chapter 3 The I O Cable Grounding section did not specify the part numbers for the Need to Be Documented grounding bars and clamps needed for proper installation These have been added to the manual Not Documented axis were not documented These have been added to the manual Incorrect Part Numbers Listed Chapter 3 The incorrect part numbers were given for the Terminal Board Connection for Terminal Block cables The incorrect part numbers listed were IC800CBL324 and Connection Cables IC800CBL325 These part numbers should have been IC693CBL324 and 1C693CBL325 respectively and have been corrected Input IN4_C Wiring Not Chapter 3 The appropriate wiring for input IN4_C was n
3. inputs use faceplate inputs IN1 and IN2 which can be either single ended or differential In Analog mode the Axis 1 and 2 strobe inputs use faceplate inputs IOS and 106 which are single ended only Axis 3 always uses IO5 and IO6 as the strobe inputs Important Product Information C693 DSM302 Module 5 GFK 1465E NOTE The input circuits for IO5 and IO6 contain 4 7k pull up resistors to internal 5v If no signal is connected to these inputs the input will always appear to be ON Normally a single ended TTL or CMOS driver must be used to drive these circuits from the strobe sensor The strobe inputs are summarized in the table below Axis 1 Axis 2 Axis 3 Servo Type Strobe Inputs Strobe Inputs Strobe Inputs INI A IN2 A INI B IN2 B 105_C 106 C Single Ended Single Ended Single Ended or Differential or Differential Digital IO5_A IO6_A 105_B IO6_B 105_C 106_C Single Ended Single Ended Single Ended Problems Resolved by this Firmware Release 1 41 Drive Disable Delay DisDly timeout parameter functions incorrectly when configured to values less than 8ms The Drive Disable Delay parameter controls the time the motion controller performs regenerative braking versus dynamic braking Prior to the Drive Disable Delay timeout dictated by the parameter in question the control uses regenerative braking After the Drive Disable Delay timeout period expires the control switches modes to dynamic braking However in firm
4. to Follower mode operation Module Sometimes Halted Responding to COMMREQ Commands When the DSM module was receiving a high rate of COMMREQ commands from the PLC CPU and was simultaneously executing a series of short move commands the module would sometimes halt execution and flash a 6 count 7 count error code on its STAT LED see Appendix B of GFK 1464 DSM302 for IC693 PLCs User s Manual for details This timing problem was corrected in firmware version 1 10 8 Important Product Information C693 DSM302 Module GFK 1465E Features and Functionality Introduced in this Release 1 41 Release 1 41 has no new features The purpose of this release is to resolve the problem described in the section Problems Resolved by this Firmware Release 1 41 New Features and Functionality Introduced in Release 1 40 DSM Analog Mode The current DSM module is enhanced in firmware version 1 40 to provide an analog servo interface The controller provides a 10 volt analog velocity command interface signal The analog interface supports third party motor amplifier sets that support a 10 volt velocity command and a quadrature encoder position feedback interface The function is currently implemented in the APM product line and allows the DSM to support the same motors and amplifiers as the existing APM controller Enhanced Follower Accuracy The DSM follower feature accuracy is enhanced in DSM firmware version 1 4 In Follower mode the maste
5. version 1 41 Boot 44P725986 408B App 44S8750607 G01R06 Firmware Update Kit 44A732298 G05 firmware version 1 41 Applicable Documents DSM302 for IC693 PLCs User s Manual IC693PLC Axis Positioning Module APM Programmer s Manual Special Operational Notes 1C693 CPU Firmware Use of DSM302 firmware version 1 41 requires that the associated IC693 CPU be equipped with version 6 50 or higher of the CPU firmware Motion Programmer Motion programs 1 10 if required must be created edited with separate Motion Programmer software DSM302 firmware version 1 41 requires that version 1 50 or higher of the APM300 MS DOS Motion Programmer software be used Configuration Configuration Software Requirements The DSM302 firmware version 1 41 may be configured with any of the following software products Important Product Information C693 DSM302 Module 3 GFK 1465E e Version 8 02 or higher of the MS DOS Programming Software will allow basic configuration However version 9 00 or higher of the MS DOS Programming Software is required to fully configure the expanded A B ratio feature see the Expanded Follower A B Ratio subject in the Features and Functionality Introduced in Release 1 20 section later in this document e Any version of the Windows based programming configuration products Essential Configuration Parameters The following configuration parameters will not default to the settings required for m
6. February 2002 GFK 1465E IMPORTANT PRODUCT INFORMATION READ THIS INFORMATION FIRST Product 1C693 DSM Module DSM302 with Firmware Version 1 41 1C693DSM302 AF Introduction Some of the information in this document is not available elsewhere so we recommend you save it for future reference This document covers the following subjects e Basic features of the DSM302 module e Special Operational Notes e Problems resolved in the latest firmware release version 1 41 e Problems resolved and new features in previous firmware versions Basic Features of the DSM302 Product Description The DSM302 Module is a two axis motion control module which is highly integrated with the logic solving and communications functions of the IC693 PLC Two primary control loop configurations are provided Standard mode and Follower mode The basic capabilities of the DSM302 are described below Performance e Digital Signal Processor DSP provides vector control of GE Fanuc AC servos e Servo loop update Digital Mode 250 uSec torque 1 mSec velocity 2 mSec position Analog Mode 2 mSec position e Block processing time under 5 mSec e Velocity Feed Forward and Position Error Integrator to enhance tracking accuracy e High resolution of programming units Position 8 388 608 8 388 607 User Units Velocity 1 8 388 607 User Units sec Acceleration 1 134 217 727 User Units sec sec Ease of Use e Simple an
7. actory regarding custom length cables e C693CBL324 1 meter terminal board connection I O cable e 1C693CBL325 3 meter terminal board connection I O cable e IC800CBLO001 1 meter servo command cable e IC800CBL002 3 meter servo command cable e 1C693CBL316 Motion programmer communications cable The I O and command cables listed above are custom manufactured with special shielding and internal construction Substituting non approved cables may adversely affect the servo system Terminal Boards Two terminal boards for user I O connections are available for use with the DSM302 as described below e 1C693ACC335 Servo Axis terminal board e 1C693ACC336 Auxiliary terminal board These terminal boards provide screw terminal connections for I O signals such as Position Strobes Home Switches Limit Switches Analog Inputs and Analog Outputs For additional information refer to Chapter 3 and Appendix E of the DSM302 for IC693 PLCs User s Manual Caution The terminal blocks contain Metal Oxide Varistor MOV circuit protectors which prevent excessive electrical energy from affecting the DSM302 The maximum recommended input voltage for any of the 24v I O circuits is 30 VDC with respect to earth ground S terminal or circuit common Strobe Input Differences between Analog and Digital Mode The strobe input faceplate pins for Axis 1 and Axis 2 depend on the DSM servo mode Analog or Digital In Digital Mode the Axis 1 and 2 strobe
8. any applications and must be changed by the user Caution Fdback Type and Ctl Loop MUST be changed first Any change to either Fdback Type or Ctl Loop resets all other parameters to default values AI AQ Len Set according to the minimum requirements of your application Setting 40 6 can be used for Standard mode Follower mode requires at least setting 50 9 if Master Axis position and velocity are to be monitored by the PLC Setting 64 12 provides the maximum amount of analog I O references Fdback Type Must be changed to DIGITAL for digital servos or ENCODER for analog servos Feedback types LINEAR RESOLVR CUSTOMI and CUSTOM2 are not supported in this release of the firmware Cil Loop Select STANDARD for Standard control loop mode or FOLLOWER for Follower control loop mode CCL2 is reserved for special applications CCL1 is not supported in this release Servo Cmd Must be changed to DIGITAL or ANALOG DUAL mode is not supported in this release Motorl Type For Digital servos must be changed to the correct motor type Select type 0 if Motor2 Type either no servo is used or if ANALOG mode is used Pos Err Lim Change from default setting of 4096 to a typical value of 15000 30000 Pos Loop TC Change from default setting of 1000 ms to a typical value of 30 50 mSec Vel at 10v Must be changed to 139 820 User Units Counts for Digital servos Reference the DSM manual Revision B for correct Analog servo settings
9. d powerful instruction set e One axis or two axis motion programs with synchronized block start e Program support for a short motion program called Program Zero that can be created in the MS DOS programming software configuration function e Nonvolatile flash storage for 10 programs and 40 subroutines e User scaling of programming units in Standard mode only MS DOS and Windows are registered trademarks of Microsoft Corporation 2 Important Product Information C693 DSM302 Module GFK 1465E e Generic programming using command parameters as operands for Acceleration Velocity Move and Dwell commands e Configured with a variety of MS DOS or Windows configuration software e Automatic data transfer between PLC tables and the DSM302 without user programming e Fase of I O connection with factory cables and terminal blocks as well as a serial port for connecting programming devices Versatile I O e Control of Digital AC servos and Analog servos with 10v Velocity Command Interface e Home and overtravel switch inputs for each servo axis e Two position capture strobe inputs for each position feedback input e 5y 24v and analog I O for use by the PLC e Incremental quadrature encoder input for Follower mode master axis e 13 bit analog output for each auxiliary axis can be controlled by PLC or used as servo tuning monitor Product ID 1C693DSM302 AE Hardware ID AP3B1 44A737294 G01R03 or later Software ID Firmware
10. et Aux Axis 3 Position command was enhanced to execute regardless of the axis current velocity In firmware version 1 00 the command would be ignored and a 0X52 axis status error reported if the axis velocity exceeded 128 counts per second Restrictions and Open Problems Restriction Problem Axis Mode LINEAR may not operate correctly if Pos EOT Hi Limit or Neg EOT Lo Limit Axis Mode LINEAR should not be selected when Ctl Loop FOLLOWER MCON can be left enabled when aborting a Jog Return Data Selector does not work if Motor Type 0 Follower master velocity is not initialized during 6 ms after follower disabled If Axis Mode LINEAR the axis will stop at the configured Positive Negative End of Travel limits if these values equal the corresponding Hi Lo Count Limits However you may not be able to jog back off the EOT To avoid this problem when using Axis Mode LINEAR always set Pos EOT below to a lower value than the Hi Limit and Neg EOT above to a higher value than the Lo Limit For example if the Hi Limit was set to 1000 and the Low Limit to 1000 the Pos EOT could be set to 990 and the Neg EOT to 990 In Follower Mode if the Axis Mode is set to LINEAR the Pos EOT Neg EOT values are internally set to the corresponding Hi Lo Count Limits Because of the problem listed above a Jog or programmed Move may not work at the configured EOT limit In addition the EOT limits do not apply to
11. imeout Firmware version 1 30 was enhanced to internally limit the Jog Velocity to 1 000 000 count sec If the module is configured to a number greater than 1 000 000 counts sec the module uses the maximum jog velocity of 1 000 000 count sec Follower Deceleration Ramp Reentry after Drive off on In follower mode if follower is disabled and then the drive is disabled motion will stop However the module continues to calculate the deceleration ramp while the follower is disabled If the deceleration ramp has not reached zero prior to the drive being re enabled the module will issue a velocity command corresponding to the current deceleration ramp value and complete the deceleration ramp This was corrected in firmware version 1 30 such that the deceleration ramp is not re entered Problems Resolved by Firmware Release 1 20 Input IN4_C Does Not Function As Described The on off state of the IN4_C input see GFK 1464 DSM302 for IC693 PLCs User s Manual chapter 5 DSM302 to PLC Interface for details was inverted from what was documented This was corrected in firmware version 1 20 such that the on off state of the input matches the documentation Important Product Information IC693 DSM302 Module 7 GFK 1465E Firmware Reports D6 Error Sporadically during Normal Operation Previous firmware contains an error that causes a D6 error to be reported incorrectly during normal operation The nature of the firmware error also causes
12. ion loop resolution at the expense of maximum supported motor velocity was added to the product in firmware release 1 20 Prior to this release a non configurable position loop resolution of 8192 counts per encoder revolution was provided The table below describes the various selections now supported along with the maximum supported motor velocity for each setting Note that the configuration data is specified by entering a value of 1 to select parameter 1 in the Tuning Parl or Tuning Par2 field of the Axis 1 screen for axis 1 or Axis 2 screen for axis 2 The appropriate resolution setting value 0 3 is then entered in the corresponding Tuning Dat1 or Tuning Dat2 field in the Axis 1 screen for axis 1 or Axis 2 screen for axis 2 Enhanced Position Loop Resolution Selections Supported Encoder Resolution Maximum Motor Velocity Configuration Data in Counts per Revolution Revolutions per Minute 8192 cts rev 4400 rpm a eae a ee 16384 cts rev 3662 rpm 32768 cts rev 1831 rpm 65536 cts rev 915 rpm Default Setting 2 Some motors are restricted to a lower maximum rpm rating Features and Functionality Introduced in Release 1 10 HV Motors Support for the following three HV motors was added in firmware release 1 10 Motor Model Motor Type Code 012HV 3000 3 022HV 3000 030HV 3000 5 10 Important Product Information IC693 DSM302 Module GFK 1465E Set Aux Axis 3 Position Command Enhancement The S
13. motion generated by Follower Master Axis inputs Therefore Axis Mode LINEAR should not be selected for either servo axis when Ctl Loop FOLLOWER If the following sequence is followed exactly MCON will be left on in error following the cessation of all motion Begin a Jog operation turn on the abort bit to abort the jog turn off the jog bit wait for motion to completely stop then turn off the abort bit In digital mode with Motor Type 0 the User Selected Return Data for that axis no longer operates Thus with Motor Type 0 the user will not be able to view data such as the firmware revision number Follower axis may jump during the first cycle after the follower is disabled when configured for ACC RAMP This is due to a 6 ms delay in master velocity initialization in the master velocity smoothing algorithm
14. opriate warning error codes notify the user about abnormal operation see error table below Master a a greater than 0 8 velocity limit no distance compensation a Error in calculation Error in calculation during ramp up gt ramp up Axis Status Only Programmed makeup time is not long enough for trapezoidal correction of Axis the makeup distance ED Status Only Velocity limit violation during ramp Status Only Time limit violation during acceleration sector of the distance correction Important Product Information IC693 DSM302 Module 9 GFK 1465E The figure below shows the velocity profile during the follower ramp cycle Note The enhanced follower make up may affect existing applications that use the old follower make up feature max Vel 0 8 Vlim a an le eres Follower l Make up Disabled distance H correction gt l Velocity Features and Functionality Introduced in Release 1 20 Expanded Follower A B Ratio The A B slave master follower ratio has been expanded from the original range of 32 1 to 1 32 to a range that supports 32 1 to 1 10 000 Existing AQ command 2Dh can be used to specify an expanded range at runtime Specifying the expanded range ratio greater than 1 32 at configuration time requires release 9 0 or higher of the MS DOS Programming Software or Windows based Programming Software release 2 11 or higher l Time Enhanced Position Loop Resolution Enhanced posit
15. ot described The description Described has been added Final Home Velocity Valid Chapter 4 The Configuring the DSM302 section incorrectly specified the valid range Command Range Incorrectly as 1 8 388 607 The range is actually 1 65535 and has been corrected in the Specified manual Select Return Data Command Chapter 5 Section incorrectly stated that information is returned in the Commanded Incorrectly Described Position AI word for each axis Data is actually returned via the User Selected Data AI word for each axis Text has been corrected Wrong Graphic Used for Chapter 7 Figure Figure showed an expected velocity profile for a program example Velocity Profile describing hanging the DSM302 when distance runs out The incorrect graphic that was included has been replaced with the correct one Documented described as a find home while follower enabled error Wire Size Screw Torque and Appendix E The wire size screw torque and MOV descriptions for terminal block MOVs for Terminal Blocks assemblies IC693ACC335 and IC693ACC336 were not specified These Not Specified descriptions have been added Problems Resolved by Firmware Release 1 10 Encoder 3 Home Position During a Find Home cycle on the Aux 3 axis the Encoder 3 home position was not registered correctly in firmware version 1 00 when the encoder marker pulse was sensed This was corrected in firmware version 1 10 Note that this problem only pertained
16. r axis position is sampled 1 0 mSec to 1 5 mSec prior to using the data within the control This sampling delay causes the follower slave axis to have a measurable and predictable based upon motor velocity following error To address the delay a master axis position delay compensation has been added in release 1 4 The delay compensation uses the master axis velocity to correct the follower master position and eliminate the following error due to master axis sampling delay Features and Functionality Introduced in Release 1 30 Enhanced AI and oI Processing The internal DSM update rate for I data and AI data except for the Actual Velocity data has been increased from once every 10 milliseconds to once every 2 milliseconds Actual Velocity data is updated every 128 milliseconds Enhanced Follower Axis Ramp Control The Follower Axis Ramp Control Function is enhanced in DSM firmware release 1 30 The enhancement improves motion smoothness Prior to this release when the follower was active and the master in motion the acceleration deceleration control during the make up correction phase was not controlled by a velocity profile This could cause unwanted machine shock The enhanced method uses a trapezoidal velocity profile to address this problem During the entire make up correction phase the acceleration deceleration is limited to the jog acceleration value Also during the correction the velocity is not allowed to exceed the maximum Appr
17. sult was that if the DSM configuration used 6 or 9 AQ words the Force D A command for Axis 3 and Axis 4 operated incorrectly This has been corrected in firmware version 1 40 such that the error no longer occurs Problems Resolved by Firmware Release 1 30 AQ Command 30h Causes Module to Crash Issuing an AQ command of 30h Set Internal Master Velocity in Follower to a value larger that 32 767 999 generated a fatal error NMI generated watchdog timeout This was fixed in firmware version 1 30 Error checking was added to generate a warning when values outside the valid range 1 000 000 1 000 000 counts sec are entered If values outside the valid range are entered the command is ignored and error code01E9 for Axis 1 or 02E9 for Axis 2 is reported IPI for Release 1 20 Contained Inaccurate Encoder Position Resolution Data The description for the Enhanced Position Loop Resolution function description was not clear The description was improved in the IPI for release 1 30 Turn off CONFIG LED when Flashing Error Code A fatal error did not turn off the CONFIG LED when a fatal error code occurs Firmware version 1 30 was updated to turn off the CONFIG LED when a fatal error code is issued Jog Vel User Units Counts Configuration Value Causes Module to Crash Configuring the module for User Units to Counts ratio of greater than 1 3 and Jog Vel 8 388 607 caused a fatal error NMI generated watchdog t
18. ware versions prior to release 1 41 if the Drive Disable Delay time is set to a value less than 8ms the motion controller does not switch from the regenerative braking mode to the dynamic braking mode leaving the motion controller to stop the motor shaft by using only the regenerative braking mode While in this state if there is an external force applied to the static motor shaft motor current will flow in the motor amplifier set If enough force is applied for a sufficient period of time this can cause a failure in the regenerative power resistors on the amplifier This issue has been corrected in firmware release 1 41 With this release the controller will switch from the regenerative braking mode to the dynamic braking mode even if the Drive Disable Delay is set to a value less than Sms Caution Be aware that if you upgrade a DSM302 to release 1 41 in a system where the Drive Disable Delay parameter is already configured to less than 8ms the braking characteristic of the system will change This change is related to how the motor will stop since the DSM will now switch from the regenerative braking mode to the dynamic braking mode 6 Important Product Information IC693 DSM302 Module GFK 1465E Problems Resolved by Firmware Release 1 40 EN3 EN4 LEDs Flash when Performing Slow Jog Function When performing a slow jog LEDs EN3 and EN4 incorrectly flashed The problem was caused by an internal Axis 3 Axis 4 AQ processing error The re
Download Pdf Manuals
Related Search