Home

Heratherm AP Mechanical Oven Manual - Cole

1. 9 2012 Thermo Fisher Scientific Inc All rights reserved These operating instructions are protected by copyright Rights resulting thereof particularly reprint photomechanical or digital postprocessing or reproduction even in part are only allowed with the written consent of Thermo Electron LED GmbH This regulation does not apply to reproductions for in plant use The contents of this operating instructions manual may change at any time and without any prior notice In case of conflicting translations into foreign languages the German language version of these operating instructions shall be binding Trademarks Heratherm is a registered trademark of Thermo Scientific Thermo Scientific is a brand owned by Thermo Fisher Scientific Inc All other trademarks mentioned in the operating instructions are the exclusive property of the respective manufacturers Thermo Fisher Scientific Robert Bosch Strafse 1 D 63505 Langenselbold Germany Thermo Electron LED GmbH is an affiliate to Thermo Fisher Scientific Inc 81 Wyman Street Waltham MA 02454 USA Thermo Fisher Scientific Inc provides this document to its customers with a product purchase to use in the product operation This document is copyright protected and any reproduction of the whole or any part of this document is strictly prohibited except with the written authorization of Thermo Fisher Scientific Inc The contents of this document are subject to c
2. Preparing the manual wipe spray disinfection 9 2 Touching live electrical components may cause a lethal electric shock Before connecting the oven to the power supply check the plug and power cord for damage Do not use damaged cables for connecting the oven to the power source Heratherm Thermo Scientific Cleaning and Disinfection Wipe Spray Disinfection The surfaces of the work space may be contaminated Contact with contaminated cleaning liquids may cause infections Disinfectants may contain harmful substances When cleaning and disinfecting always observe the safety instructions and hygiene guidelines Wear safety gloves Wear safety goggles Wear mouth and respiratory system protection gear to protect your mucous membranes Observe the safety instructions of the disinfectant s manufacturer and the hygiene supervisor Predisinfection 1 Remove all samples from the work space and store them in a safe place 2 Spray disinfectant onto the surfaces of the work space and of the accessories or wipe the surfaces clean using disinfectant 3 Allow time for the disinfectant to act as specified by the manufacturer N Q TE oS in ng hard to reach Spray the sensor and other hard to reach components with disinfectant Thermo Scientific Heratherm 9 3 Cleaning and Disinfection Wipe Spray Disinfection 9 4 Heratherm Thermo Scientific LLL
3. message shown on dis play Sensor Error E113 Sample sensor damaged Audible alarm activated Call service The actual measured value message shown on dis is out of range play ADC Error E114 A D converter does not Audible alarm activated Call Service supply a plausible output message shown on dis Measurement across refer play All control circuits dis ence resistor R403 has abled failed ADC converter may be defective Watchdog error E115 Watchdog test failed on Audible alarm activated Call service Clearing should mute the audible alarm de energize the alarm relay and clear the message from the control panel display Thermo Scientific Heratherm 12 3 Error Codes 12 4 Heratherm Thermo Scientific ee 86h Technical Data The technical data are valid only for an empty device equipped with three shelves a spray painted outer enclosure and a power line voltage 120 V 60 Hz Table 13 1 and 208 240 V 60 Hz Table 13 2 Options may have an impact on the specified performance Table 13 1 Technical Data OGS and OMS Series 120 V Table top ovens Parameter Unit OGS60 OGS100 OGS180 OMS60 OMS100 OMS 180 Process Work Space Atmosphere Min C F 50 122 50 122 50 122 50 122 50 122 50 122 Max C F 250 482 250 482 250 482 250 482 250 482 250 482 Temperature deviation K 4 5 4 0 4 5 4 0 445 440 3 7 3 3 43 0 425 43 5 43 0 from set value at 150 C 302 F spatial Max value
4. 3 11 Installing the Anti tilt Anchor acier Ed anenai REN ia ane EE ado im tud 3 12 Floor stand HAE SA RT 3 14 Chapter 4 upldi oggnpe M 4 1 Heratherm OGS Series Oven Overview MEM n 4 1 Heratherm OMS Series Oven Overview viccsracasenssndalanavaonnsincancananedessanenesnoss annsasd aun beds avcannrasasuayeecarantnans 4 8 Safety Devices TUNER RUN 4 11 Work Space Atmosphere siess nesnsecienseiestaiawsgsaraisbicen ea ae E R DEEA E R 4 11 Thermo Scientific Heratherm i Contents Chapter 5 Chapter 6 Chapter 7 Chapter 8 Sensing and Control SYsEERTussistete taa peace oso n it Po anterius RUE NOR QUA E DOR Qu Pup Ropa PORE 4 11 Bata Communications Beo larin Interfaee us caste ies akc etia oto bao e ades oe or acida 4 12 RS 232 Interface aiat oda em Ren HB Ora Succ toma sad RD e DIR Re DAS SER UE E 4 12 AC Power SOCK Cte hash Gaisted iPod etr eia napi a leti la v OM EH on iv M Res HO aai 4 12 Jg E 4 13 Work Space C mpon ntS d oou rc ro ester meg I peret ia o ive de IE E SRM CIR Le n bte eda 4 13 Inner i harbor ene o deren te ent me dV 4 13 ACCESS DORD eire cote radi nd a isst feng a atod blo chic aide E A betont 4 13 MIDE ACCESS POLES P 4 15 APA UD occas ese i ieee et ce oh cece ac Pe caret Scat eden ete 5 1 Installing the Shelf System of the table top ovens alin err peo op nda la ths Madea hanaadendap
5. Handling and Control Settings Table 7 11 Entering the Calibration Reference Temperature Manually The word USEr appears in the display pane Press to confirm the selection In the settings dialog that appears set the temperature measured with the external reference sensor by using or and confirm your settings with The newly entered value will be stored and used to calibrate the internal temperature sensors with the value measured by the reference sensor The display returns to its default mode The Settings icon in the menu bar will go out Temperature Display Unit The Settings gt C F menu item allows for toggling the unit used for displaying temperatures between degrees Centigrade and Fahrenheit Note This setting does not have any impact on data logging via the RS 232 interface Any temperature data that is logged to a computer for operational parameter documentation purposes is handed over in C Table 7 12 Toggling the Temperature Display Unit Press to activate the menu bar then use 1223 or MENU to select the Settings icon and press to confirm Press to switch to the C F menu item The text C F is flashing in the display pane Thermo Scientific Heratherm 7 11 Handling and Control Settings Table 7 12 Toggling the Temperature Display Unit Press the button The currently unused temperature unit C or F is f
6. When taking the oven into operation for the first time allow some time for stabilization before switching on to avoid condensation forming on live parts Switching the Power Line Voltage The 240 V versions of Heratherm ovens are equipped with a wide range power supply unit that permits them to be operated on a 240 V or 208 V power source For optimum heating performance though the operating parameters of the built in controller can be customized in software to obtain the best performance on either line voltage 240 V or 208 V This is achieved by entering two specific configuration codes in the Settings gt Configuration dialog explained in Configuration on page 7 12 Table 5 1 Line Voltage Selection Codes Line Voltage Enter Code 208 V 0208 240 V 0240 Thermo Electron LED GmbH Heratherm 5 11 Start up Connecting the RS 232 Interface Connecting the RS 232 Interface Replacement should only be carried out by skilled and authorized qualified personnel of electrotechnology signal engineering The RS 232 data communication interface supports the querying of status information and temperature data from the oven by entering basic commands in a standard terminal window provided by your computer s operating system The interconnection requires a standard RS 232 cable with 9 pin connectors and a straight 1 1 pinout without any crossed wires which is not supplied with the oven Users may em
7. TE Benefits of using separate electrical feeders Although several devices may be operated on the same electrical feeder if the rated current is not exceeded we strongly recommended to provide one feeder with a dedicated upstream circuit breaker per oven to avoid the failure of multiple devices in case of an electrical fault Connection to the Power Supply Source l 5 10 Heratherm Before connecting the oven to the power source check to see if the power supply voltage corresponds with the specifications on the nameplate on the front of the oven If the voltage V and current A ratings given are not as required do not connect the oven to the power source Connect the IEC connector to the socket at the rear of the oven Route the power cord along a path that does not cross exhaust air piping or passageways With stacked devices keep the power cord away from hot spots on the other oven in the Connect the protection earthed plug of the power cord to a correctly protection earthed and earth leakage circuit breaker fused power socket Make sure the power cord is not subjected to tensile or compressive force Thermo Electron LED GmbH Start up Mains Connection Power outlets Make sure that power outlets remain freely accessible at all times Sample ECO Sensor not used RS 232 interface Alarm contact not used Power socket Figure 5 14 AC Power Supply Socket Condensation
8. Calibration on page 7 11 N Q TE Excessive Work Space Temperatures Excessive work space temperatures subsequent to a calibration run can be reduced by leaving the door open for approx 30 seconds Thermo Scientific Heratherm 10 3 Maintenance Replacing the Door Seal Replacing the Door Seal The door seal of the outer door is located in the retaining slot The door seal should be inspected for any signs embrittlement every six months when the oven has been used at maximum temperatures of up to 250 C 482 F No tools are required to replace the seal DOnanpnaagnmnmnu Figure 10 1 Door seal replacement example showing OMH Series oven 1 Pull the seal out of the guide slot 2 Starting on the hinge side of the door position the seam of the new seal at the location indicated by the arrow in figure 10 1 above 3 Gently press the seal into the slot working around the circumference of the door In doing so be careful not to stretch the seal 4 Make sure that the retaining rail taper is positioned correctly in the slot and that the seal is flush with the door frame Replacing the Power Cord When the device s power cord is damaged it must be replaced with an original spare part Using a standard power cord with a lower temperature withstand class is prohibited Returns for Repair Prior to returning any materials please contact our Customer Service Department for a Return Materials Au
9. Typical value Temperature deviation K 0 4 0 4 0 5 0 3 0 3 0 3 from set value at 150 C 302 F over time Max value Typical value Heat up time work space min 25 15 25 19 25 21 20 17 20 12 20 15 unoccupied from 25 C 77 F to 98 of set temperature of 150 C 302 F Max value Typical value Recovery time work min 9 8 9 8 9 8 5 3 5 3 5 4 space unoccupied door open for 30 s to set temperature Max value Typical value Heat dissipation to W 194 10 261 10 320 10 316 10 4594 10 51341096 environment at set temperature of 150 C 302 F and room temperature of 25 C 77 F Max air change at ni 19 16 18 33 61 31 150 C 302 F Overall dimensions Height mm in 720 820 920 720 820 920 28 3 32 3 36 2 28 3 32 3 36 2 Width mm in 530 640 640 530 640 640 20 8 25 2 25 2 20 8 25 2 25 2 Thermo Scientific Heratherm 13 1 Technical Data Table 13 1 Technical Data OGS and OMS Series 120 V Table top ovens Parameter Depth Overall weight Loading capacity Loading capacity per shelf Max overall loading capacity per device Electrical data Power rating Maximum current Earthing system e g 1 N PE Power line frequency Power line voltage 10 96 IP protection system Protection class Overvoltage category to IEC 60364 4 443 Device fusing building side Device fusing on PCB Environmental conditions Min ambient temperature Max ambient
10. 1 1 1 1 1 1 2 2 2 2 0 1 2 3 4 5 6 7 8 9 0 1 2 3 L CI c c cC wc G ia WD coc 4 6 Heratherm Heratherm OGS 750 Series Front View Outer door Door hook catch Unit caster Air baffle bottom Wire mesh shelf Door latch Temperature sensor Exhaust air tube Door hinge Air baffle side Thermo Scientific Figure 4 6 Heratherm OGS 750 Series Rear View Outer door XO O00 ON VA 4 Q2 Nae OO CS CS CCS c L C IO Cc c c cocci Thermo Scientific Unit caster Exhaust air tube Anti tilt anchor Electronics compartment Inlet air tube Hinge Handle Display Nameplate on sidewall Hinge Product Description Heratherm OGS Series Oven Overview Heratherm 4 7 Product Description Heratherm OMS Series Oven Overview Heratherm OMS Series Oven Overview Heratherm OMS Series OMS is brief for Oven with Mechanical convection for Standard laboratory applications general protocol fan convection ovens come equipped with the following features high precision work space temperature control adjustable in steps of one degree up to 250 C 482 F a fixed speed fan for optimizing temperature uniformity throughout the work space a mechanically operated damper for venting the work space equipped with an external slider rotary button control an On and Off timer two wire mesh shelves 4 8 Heratherm Thermo Scientific Product Description Herathe
11. 2 Technical Data OGS and OMS Series 208 240 V Table top ovens Parameter Unit kg lbs kg lbs Loading capacity per shelf Max overall loading capacity per device Electrical data Power rating Maximum current A Earthing system e g 1 N PE Power line frequency Hz Power line voltage V 10 IP protection system Protection class Overvoltage category to IEC 60364 4 443 Device fusing building A side Device fusing on PCB A Environmental conditions Min ambient temperature C F Max ambient temperature C F 96 r F 96 r H Max humidity in service non condensing Min storage temperature C F Max storage temperature C F r F 96 r H Max humidity in storage non condensing Post transport acclimation h time Noise level dB A Pollution degree to IEC EN 61010 1 Site conditions Maximum altitude above m y ASL sea level Minimum side clearance mm in Minimum front clearance mm in Minimum back wall mm in clearance Minimum bottom mm in clearance Minimum top clearance mm in 13 4 Heratherm OGS 100 OGS 180 25 55 50 110 75 165 3360 3360 14 0 14 0 1 N PE 1 N PE 60 208 240 IP 20 ll 16 2x16 18 65 32 90 80 on condensing 20 68 60 140 90 non condensing no inherent noise 2 2000 2187 50 2 690 27 2 80 3 2 814 32 200 8 300 12 OMS 100 OMS 180 25 55 50 110 75 165 3360 3360 14 0 14 0 1 N PE 1 N PE 60 208 240 IP 20 l
12. 3 0 4 0 3 0 0 5 35 31 60 53 lt 8 lt 6 lt 9 lt 7 520 10 795 10 20 8 1655 65 2 755 1215 29 7 47 8 770 30 3 136 300 182 401 40 88 75 165 150 330 2640 3240 11 0 13 5 1 N PE 1 N PE 60 208 240 IP 20 Heratherm 13 5 Technical Data Table 13 3 Technical Data OGS Series Floor stand ovens Parameter Unit Overvoltage category as per IEC 60364 4 443 Device fusing building side A Device fusing on PCB A Environmental conditions Min ambient temperature C F Max ambient temperature C F Max humidity in service non condensing r F 96 r H Min storage temperature C F Max storage temperature C F Max humidity in storage non condensing r F r H Post transport acclimation time h Noise level dB A Degree of pollution as per IEC EN 61010 1 Site conditions Maximum altitude above sea level m y ASL Minimum side clearance mm in Minimum front clearance mm in Minimum back wall clearance mm in Minimum top clearance mm in OGS 400 OGS 750 II 16 2x16 18 65 32 90 80 non condensing 20 68 60 140 90 non condensing 2 no inherent noise 2 2000 2187 120 4 7 810 31 9 120 5 9 200 8 670 26 4 1 Temperatures as low as ambient 10 C can be selected this requires open damper and no additional heat in unit 13 6 Heratherm Thermo Scientific LLL m Spare Parts and Accessories Material No Description 50073715 Fuses 5 0 A 250V T 6 3 X 32
13. 50127513 Kit fan system Heratherm OMS 60 230 V 50127514 Kit fan system Heratherm OMS 100 and OMS 180 230 V 50127515 Heating coils for Heratherm OMS 60 OMH 60 OMH S 60 at a voltage of 230V 50127519 Heating coils for Heratherm OMS 100 OMH 100 OMH S 100 OMS 180 OMH 180 OMH S 180 at a voltage between 208 and 240 V 50127532 Circulation fan OMH OMH S D 180 mm 7 1 inch H 28 mm 1 1 inch 50127544 Door window seal for Heratherm heating and drying ovens 50127555 Kit fan system Heratherm IMH 60 IMH S 60 OMH 60 and OMH S 60 IMH 100 IMH S 100 IMH 180 and OMH S 180 230 V 50127556 Kit fan system Heratherm OMH 100 OMH S 100 IMH 180 IMH S 100 and OMH 180 230 V 50127557 Mechanical air inlet slider for Heratherm OMS 60 and OGS 60 50127558 Mechanical air inlet slider for Heratherm OMS 100 OGS 100 OMS 180 and OGS 180 50127559 Kit electrical air flap Heratherm Advanced Protocol and Advanced Protocol Security ovens 50127566 Fresh air filter for OMH OGH OMH S OGH S 50127662 Fresh air filter OGH OGH S OMH OMH S 50127741 Support stand with castors for Heratherm 60L 50127742 Support stand with castors for Heratherm 100L 50127743 Support stand with castors for Heratherm 180L 50127761 Wire mesh shelf OGS 60 OGH 60 OGH S 60 including 2 shelf sup ports 50127762 Wire mesh shelf OGS 100 OGH 100 OGH
14. RUE 9 1 Wipe Spray Liste te Ete ic hia buen utei pieno alere bd eH a re osi clare ibiasesld casual actu da tebe 9 1 Preparing the manual wipe spray diste CtORL erede etna record eed eb rn ERU RR RP IDE Uit UE dE 9 2 Predisintection jo iai oai ce lota a oe abe LA ioco fun ei a ROO RUE 9 3 Chapter 10 cleri 10 1 Inspecuonsand Geeks iieri toisin as naka oi aE aaa An e E a Eea aa iaaa n ESA aa i Ra 10 1 Service TGtervalsusie enai areatan ceses ei ite RE Ce M Rep IRL HU Ene ERR Eeoa Sadete RR CAR sin EH RM TE aLi sha chacs 10 2 Preparing Temp ratur al tite ron i sonsevcixitecimuie aro bene toto er da lceeeg iib cidachdastenmuabtoceiaaseassansseubanagse 10 2 Comparison Measurement DrOCedeos ede eur tnna aem n ra en aunt evecta pete Dp DER Ibudsa 10 3 Temperature Calibration Procedure in vient tese p denti tectoe Db bt tact haine Va HUE UE DR URN IR M Ren Na Lad 10 3 Replacing the Door Seal actae dod Sa s rice a n e tei Epis 10 4 Replacing the Power Cord o4 o BA A mien HR done aar ae aA eaa RURAL I RUM ko abo MR abe ebd dut 10 4 Rerurnsdor Real apio ablatas BEG MeV Nn Hoa td fdisto Malt aC a EG aaci i ui MM uf Ua beati d 10 4 Chiaptet 11 DIsp sal ieri es ei eres Ferdi ee ie edu desertas enc P eun es Cui 11 1 Overview OF Materials Used iius e tp aftes i sati rue t eM ema tastes AER Epi Raie 11 1 Chapt r dime T See eovee 12 1 Ghapter 13 Technical Data 2 x ssc icece ts uc
15. Technical Support immediately AWARNING Risk of injury Should sharp edges have formed in damaged areas or elsewhere on the device take all necessary precautions to protect personnel handling the oven For example have them wear protective gloves and other personal protection equipment Thermo Scientific Heratherm 2 1 Delivery of the Oven Scope of Supply Scope of Supply Ovens Quantity of components supplied pieces OGS Series OMS Series Wire mesh shelf 2 2 Support rail for shelf for table top ovens only 0 2 Shelf support 4 4 Power cord 1 1 Clip springs for table top ovens only 0 2 Operating manual 1 1 Short reference guide 1 1 2 2 Heratherm Thermo Scientific MEN E Installation Ambient Conditions Location Requirements Built in units of incubators can heating and drying ovens must be operated with an air exhaust system and exhaust hose only original Thermo accessory should be used For safety reasons the installation space should be made of non combustible materials according to DIN 4102 During installation of built in units ensure that the N O TE escaping air will be safely discharged out of the installation space Use with Air Exhaust Systems For built in units a temperature resistant and corrosion proof exhaust hose only original Thermo accessory should be used which can be connected to the air exhaust port with a draft interrupter If seve
16. m Maintenance Regular maintenance is mission critical to avoid malfunctions due to ageing and wear Failure to perform maintenance on a regular basis may result in deviations in heating performance damage to samples loss of control over temperature distribution throughout the work space Inspections and Checks To ensure the operational performance and safety of the oven their functions and the components listed below must be checked at regular intervals Regular Checks Check the oven for overall cleanliness and remove any debris from previous processes To avoid operation without an appropriate fresh air supply check the air filter optional in the air inlet for contamination Monthly Inspection Check integrity and proper seating of the door seal Swap air filter cartridge optional in air inlet Perform functional check of the control panel and of the ovens built in controller Perform electrical safety check in accordance with the relevant national regulations N O TE Functional check If safety devices were removed or disabled for inspections the oven must not be operated before the safety devices have been reinstalled and checked for their correct function Thermo Scientific Heratherm 10 1 Maintenance Service Intervals A WARNING Spare Parts and User Modifications To avoid major malfunctions of the oven and associated safety hazards that may result in deat
17. or fire protection regulations Mark hot exhaust air piping with appropriate hot surface warning signs or restrict access to such piping altogether to avoid the risk of injury through contact with hot surfaces Draft breaker Air exhaust hose Air inlet pipe Fig 1 Fig 2 Thermo Scientific Heratherm 3 3 Installation Space Requirement Space Requirement For built in units following clearances should be kept Fig 3 A B C and D see Operating Instructions of the unit E mm inch F mm inch G mm inch H mm inch 100 4 50 2 80 3 2 30 1 2 Installation Built in Units IGS Clearances as fig 3 without exhaust hose IMH IMH S Clearances as fig 3 Close air port with plug supplied with the unit OGS OMS Clearances as fig 3 with additional space to operate to air slide with air exhaust system and exhaust hose 40 mm 1 58 in 1 5 m 59 in original Thermo accessory shortened to required length installed according to Fig 1 and 2 OGH OGH S Clearances as fig 3 with air exhaust system and exhaust hose 40 mm 1 58 OMH OMH S in 1 5 m 59 in original Thermo accessory shortened to required length installed according to fig 1 and 2 Operating temperature up to max 250 C 482 F After connecting the built in unit to the electrical 8 power supply avoid damaging the power cord then sliding into the installation position When installing the oven make sure th
18. restore communication with the control panel Alarm Response Audible alarm activated message shown on dis play Reset after 30 s Alarm Clearing Instructions Power cycle the device by unplugging then recon necting the power cord If this doesn t solve the prob lem call service Mirrored Parameter Loaded E003 The controller was unable to read the user specific settings and had to resort to an emergency parame ter set held in mirrored stor age Fallback to mirrored parameter storage Device continues to run without loss of functionality includ ing user specific settings Check the latest settings for example the set value Factory Parameter Loaded E004 The controller was unable to read the mirrored param eter set and had to resort to factory preset parameters Fallback to factory preset parameters Audible alarm activated message shown on display User specific settings may be lost for example the temperature display unit preference or user programs Acknowledge by pressing Co Re enter cus tomer specific settings Default Parameter Loaded E005 The controller was unable to read the factory preset parameters and had to resort to default settings Fallback to default parame ters User specific settings will be unavailable Audi ble alarm activated mes sage shown on display The device is completely inoperative Call service Power Down Error
19. with four 4 casters The lever for releasing the caster is located above the locking lever After positioning the unit in its installation location ensure that the locking levers are pressed down on the casters To ensure the degree of stability specified by safety requirements the front casters must be turned so that they are facing forward after the unit has been positioned in its installation location and the locking levers pressed down on these casters Danger of tipping when moving Before moving the unit ensure that it has been unplugged Move the Heratherm floor stand ovens with caution Quick starts and stops can result in tipping Always ensure that the doors are closed when moving the unit Thermo Scientific Heratherm 3 9 Installation Stacking Kit Stacking Kit The stacking adapter is available only for table top ovens Material Number Description 50126665 50126666 50126667 Stacking adapter Heratherm 60L Stacking adapter Heratherm 100L Stacking adapter Heratherm 180L Scope of Delivery 1 stacking adapter lanti tilt anchor plastic bag with 2 stacking feet and 2 M x16 Torx screws Required Tools Slotted screwdriver 5 5x100 or Torx screwdriver 20x100 Installing the Stacking Feet 1 Remove the left and right blank plugs at the top blank 2 Install the stacking feet with the enclosed screws using a slotted or Torx screwdriver 3 10 Heratherm Thermo Scientific
20. 10 8419 3588 Service Toll free 8008105118 Support Mobile 4006505118 or 86 10 8419 3588 India Sales 91 22 6716 2200 Service Toll free 1 800 22 8374 or 491 22 6716 2200 Japan Sales 81 45 453 9220 Service 81 45 453 9224 Enquiries from the Rest of Asia Australia New Zealand Sales 852 2885 4613 Service 65 6872 9720 Enquiries from Countries not listed Rest of EMEA Sales 49 6184 90 6940 or 33 2 2803 2000 Service 49 6184 90 6940 Thermo Scientific Heratherm 16 1 Contact 16 2 Enquiries from Europe Austria Sales 43 1 801 400 Service 43 1 801 400 Belgium Sales 32 53 73 4241 Service 32 53 73 4241 Finland Nordic Baltic countries Sales 4358 9 329 100 Service 358 9 329 100 France Sales 433 2 2803 2180 Service 33 825 800 119 Germany Postal Address Germany Thermo Electron LED GmbH Robert Bosch Strafse 1 D 63505 Langenselbold Phone Sales Toll free 0800 1 536 376 or 49 6184 90 6940 Service Toll free 0800 1 112110 or 49 6184 90 6940 E Mail info labequipment de thermofisher com Italy Sales 39 02 95059 341 Service 39 02 95059 250 Netherlands Sales 31 76 579 5555 Service 31 76 579 5639 Russia CIS Sales 7 812 703 4215 Service 7 812 703 4215 Spain Portugal Sales 34 93 223 0918 Service 34 93 223 0918 Switzerland 41 44 454 1212 Service 41 44 454 1212 UK Ireland Service 44 870 609 9203 Sales 44 870 609 9203 Heratherm Thermo Scientif
21. C 32 F press to confirm your settings The display returns to its default mode The actual temperature measured in the work space and shown in the temperature display area starts to drop showing the progress of the cool down process Heratherm Thermo Scientific Handling and Control Timer Timer The Timer feature from the menu bar enables the user to set a countdown type on or off timer that switches the oven on or off after a preset period of time Instructions for setting an off timer are given in table 7 6 see below while its use as an on timer is described in table 7 7 on page 7 7 Programming a turn on time causes the oven to shut down until it is scheduled to restart while a turn off time keeps it running before it shuts down at the user specified time The timer starts running immediately as soon as the user confirms his or her entries Table 7 6 Setting a Countdown type Off Timer Press to activate the menu bar then use QA to select the Timer icon and press to confirm The word OFF appears in the multifunctional display pane Choose the off timer with E gt Set the hours and minutes until the oven is supposed to shut down by pressing or B then press E to confirm The display returns to its default mode In the menu bar the Timer icon is illuminated and a is rotating on the icon s face Table 7 7 Setting a Countdown type On Timer Pr
22. Description This section describes Heratherm general protocol ovens for standard laboratory applications which are available in two versions distinguished by convection method e Heratherm OGS Series general protocol natural convection ovens see Heratherm OGS Series Oven Overview on page 4 1 Heratherm OMS Series general protocol mechanical convection ovens see Heratherm OMS Series Oven Overview on page 4 8 Heratherm OGS Series Oven Overview Heratherm OGS Series OGS is brief for Oven with Gravity convection for Standard laboratory applications general protocol natural convection ovens come equipped with the following features high precision work space temperature control adjustable in steps one degree up to 250 C 482 F a mechanically operated damper for venting the work space equipped with an external slider rotary button control an On and Off timer two wire mesh shelves Thermo Scientific Heratherm 4 1 Product Description Heratherm OGS Series Oven Overview The individual features of OGS Series ovens are shown in the figures below Figure 4 1 Heratherm OGS 60 OGS 100 OGS 180 Series Front View Outer door Door latch cutout Door latch and handle Door hinge lower Levelling foot Nameplate Air baffle bottom Air baffle side Door hook catch Wire mesh shelf Support rail for wire mesh shelf Door seal Stacking pad Temperature sensor Exhaust air tube 4 2 Herathe
23. E007 Power has been cut off power outage while the device was running Audible alarm activated message shown on dis play Check the power supply Power up then device then acknowledge the alarm by pressing c Fan Error E009 OMS Series only Fan speed out of range Audible alarm activated message shown on dis play Heater disabled by controller Acknowledge by pressing Co If this doesn t solve the problem call service Config Error E012 General device configura Audible alarm activated Call service tion error message shown on dis play The device is com pletely inoperative Thermo Scientific Heratherm Error Codes Table 12 1 Heratherm Oven Error Codes Error Message amp Code OTP error E013 Root Cause Klixon contact not closed Alarm Response Overtemperature Protec tion fault Audible alarm activated message shown on display Bridging across Klixon contact has failed Alarm Clearing Instructions Restart the device If this doesn t solve the problem call service Incorrect voltage E014 The applied voltage is too high Audible alarm activated error Apply the correct voltage as E101 exceeds permissible range The triac in the heater cir cuit may be defective vated control continues on set value Audible alarm activated E101 message shown on display or too low message shown on display indicated on the na
24. EOR EAR MUN ER ANE NGA ERES REIR EBERT RENE ISES 1 5 Intended use of the deyice M M M 1 5 Correct USE csere e e cs cas E E 1 5 lhteoscadU EE 1 5 Standards ang I IFeCtVves eie ee EE Ree EROR eR ERE a EXER PR RR en E rude eS CX Vend ES 1 6 Chapter2 Delivery of the OVEN ecriccuie np nad aras sou pndx 0E connu EE rana panna n RRNA NATAAN MANA n aR CER Ra URS MERE SEP PR RR 2 1 Packaging ssc ws tcc cba wa amt rb la xr cg aO C APR INR Unit b cendi ident n ats e pod uai 2 1 Acceptance Inspection ier iter rre torte Teo ebd qe o eei VR IER IE UP CH Ge A 2 1 Scope of SUN ARP 2 2 Chapters ECL m 3 1 Pb DENN MCN 3 1 Location REquireMenits 3 1 Use with Air Exhaust Systems oet RD RE URREXRRRENUR RR EN PEURIERI ERE ERE FIERI PRSE 3 1 lntermediat SOLACE T ii Em 3 2 Dori up M CC c 3 3 Use with Air Exhaust Systems RR UR te e REI E e E EE REESE RR eas eias 3 3 Space nidi Naa 3 4 Installatiog Built in Units terrent ree eet rr RE ERE EE ERU dba XE HEY RR ed RES ACER 3 4 NL up c e 3 5 Floor Stand OVENS T ante 3 6 bct OE 3 8 Stacking 4 MCN T T EESE 3 10 Installing the Stacking Peet MNA RR 3 10 Inst lline Te Seales Adapter M
25. F mm inch H mm inch mm inch 120 4 7 50 2 0 200 7 9 200 7 9 3 6 Heratherm Thermo Scientific Installation Space Requirement 750 liter units Figure 3 3 Floor stand ovens OGS 750 dimensions and required clearances Table 3 5 Oven Dimensions Model A mm inch B mm inch C mm inch D mm inch OGS 750 1215 47 8 770 30 3 1655 65 2 670 26 4 Depth of handle display 66 mm 2 6 in not included in overall depth specified Width of hinge 23 mm not included in overall width Table 3 6 Required Clearances E mm inch F mm inch H mm inch mm inch 120 4 7 50 2 0 200 7 9 350 13 8 Thermo Scientific Heratherm 3 7 Installation Transport Transport Table top ovens For transport do not lift the oven using the doors or components attached to the oven as lift points t Figure 3 4 Lift Points NCAUTION Heavy loads Lift with care To avoid injury through physical strain such as strain traumata and slipped discs do not attempt to lift the oven alone To avoid injury through dropped loads be sure to wear Personal Protection Equipment such as safety shoes when lifting the oven To avoid crushing your fingers or hands particularly in a closing door or damaging the oven do not use any other lift points than those indicated in the illustration above 3 8 Heratherm Thermo Scientific Installation Transport Floor stand ovens The floor stand ovens come equipped
26. Installation Installing the Stacking Adapter Installing the Stacking Adapter 1 Stacking adapter HTM 60 Stacking adapter HTM 100 Stacking adapter HTM 180 AJl N Anti tilt anchor Stack as follows when using a stacking adapter numbers denote oven volumes in liters e for 60 100 180 on 180 use stacking adapter Heratherm 180L e for 60 100 on 100 use stacking adapter Heratherm100L e for 60 on 60 use stacking adapter Heratherm 60L To prevent the top oven from slipping and dropping down the following requirements must be fulfilled before devices may be stacked Only two units may be stacked together When stacking devices with the same type of enclosure yet with a different footprint the device with the smaller footprint must be placed on top of the one with the larger footprint at all times The bottom device must be correctly levelled Besure to use the appropriate stacking adapter The levelling feet on the top device must be screwed in all the way Thelevelling feet of the top device must be aligned with and placed exactly on the stacking pads of the stacking adapter Theanti tilt anchor must be installed on the top device Thermo Scientific Heratherm 3 11 Installation Installing the Anti tilt Anchor Installing the Anti tilt Anchor Table top ovens The anti tilt anchor secures the top device in a stack to a solid part of a building The anti tilt anchor is to be mounted
27. OMS Series Installing the S RELI ois s maet api pachlei i an eqs nati Pap AV Hp i MR pao ROM a oM 5 2 Figure d Suppoxk Rail Try Shel LOI ssrin nesana Guba ated suldancie ten cn cd ka e o RD UA DR di unt 5 3 Figure 5 5 Installing the Bear Air Dallleiessimeeiseiutrbteup ttv tip ise bee Dei in eeco i din eo neat lae cule Rite de 5 4 Figure 5 6 Removing the Bottom Panel T M 5 5 Figure 5 7 Bottom Panel Removed sa adhere A nianna bandit aE EAEE EEE Uv e RU ERE 5 5 Figure 5 8 Removing the Lateral Air Battle ssccaiciescasaivanededsinantdvsnetdelonsntdennealbapeuitdebiacseeddnedtssennnddanmeniwineseduipregitinnies 5 6 Figure 5 9 Removing the bottom platezuissietiscstoise imb sesta id atia bibe la ux MEER pel GRAB a MEME Saen SNAKSTER TiNa 5 7 Figure 5 10 Removing the left and right support profiles dan cebat reda beide Poeti rd Vbcba te IR UNE RRA ERE UR RE ERIS Rie 5 7 Figure 5 11 Removing the rear air baffle OGS 400 750 seuss scovataininesed levadienccasantvarsnacessins eR rre dpe e Ie ERE Y PE SUBE Un 5 8 Figure 5 12 Shelf Support Bracket Installation gecesi seseiaoratelsasosaeseanronsed pio lasticula tis iul bad fa teli teda cn plc dt 5 9 Figure 5 13 Wiremesh Shell a odios dtr leta esaii ndi secus nd uta caged asltu aat PU E ee SUD cR ad 5 9 Figure 5 14 AC Power Supply Soe T 5 11 Figure 7 1 Control Panel for Heratherm OGS Series and OMS Series OVENS issssceniacascsinsesscsscnssennssanesvansstaranciiiannes 7 1 Figur
28. S 100 including 2 shelf sup ports 50127763 Wire mesh shelf OGS 180 OGH 180 OGH S 180 including 2 shelf sup ports 50127764 Wire mesh shelf OMS 60 100 180 OMH 60 100 180 OMH 60 100 180 S including 2 shelf supports 50127767 Sample sensor for OGH S 60 OGH S 100 OGH S 180 OMH S 60 OMH S 100 OMH S 180 50127773 Thermo Scientific Stainless steel perforated shelf IMH 60 IMH 60 S OMH 60 OMH 60 S OMS 60 100 180 including 2 shelf supports Heratherm 14 3 Spare Parts and Accessories 14 4 Material No Description 50127774 Stainless steel perforated shelf IMH 100 IMH 100 S OMH 100 OMH S 100 OMS 60 100 180 including 2 shelf supports 50127777 Stainless steel perforated shelf IMH 180 IMH 180 S OMH 180 OMH S 180 OMS 60 100 180 including 2 shelf supports 50127861 Retaining springs for Heratherm incubators and heating amp drying ovens 50127862 Support rail for Heratherm IGS 60 IMH 60 IMH S 60 OMS 60 OMH 60 OMH S 60 50127863 Support rail for Heratherm IGS 100 IMH 100 IMH S 100 OMS 100 OMH 100 OMH S 100 50127864 Support rail for Heratherm IGS 180 IMH 180 IMH S 180 OMS 180 OMH 180 OMH S 180 50127914 Stainless steel perforated shelf OGS 60 OGH 60 OGH S 60 including 2 shelf supports 50127925 Stainless steel perforated shelf OGS 100 OGH 100 OGH S 100 includ ing 2 shelf suppo
29. S 750 Series Front View escaiaqene i pacti an raso nati Pap Hp i MR pulo Ra oO a ou 4 6 Figure 4 6 Heratherm OGS 750 Series Rear View scessincciassssnsisasedanen sede dude UU UA NR UU B Fan EU PE UU ERU i bidE 4 7 Figure 4 7 Heratherm OMS Series Front VJESIGouceseteisesernuenaimtieai pe teiieei ie ro pner dil pere es d pu ER PRESE INE 4 9 Figure 4 8 Heratherm OMS Senes Rear View sisdessnsuncanssanlalsnendacsnnionoasspsascanbiasancyradnics in Pad aerei coc tuno o 4 10 Figure 4 9 Sensor Mounting Location OGS Series and OMS Series Table top ovens sss 4 11 Figure 4 10 Sensor Mounting Location OGS Series and OMS Series Floor stand ovens sss 4 11 Figure 4 11 Signal Interfaces and Power Socket un uendebetdbndecsumieisiasnio uaaeb iG tes Motel apaga Rp ces f Dur tu t Ap Quads 4 12 Figure 4 12 Shelf System OGS Series Oven Table top ovens eee eee eeiseee tatnen than tha teta tnotan 4 14 Figure 4 13 Shelf System OMS Series Oven Table top ovens ccccssssessssssssscsessocssscsesssssccsanensesceatossscoeasentossees 4 15 Figure4 14 Tube Access D OPIA oae setenta mini qo trap lube tenia Basta duit tan dae put opa td qua buio du abo idi 4 16 Figure 5 1 Sliding the Retaining Spring into the Support Rallies rtdta expen Robert b toU Re RU eU RR LM E eas 5 1 Figure 5 2 OGS Series Installing the Shelving oesss cescepare ti teh siint een e Ipse c rl uNN Papae ti UR Oa a PV gea 5 2 Figure 5 5
30. arance Minimum top clearance mmyin 300 12 300 12 1 Temperatures as low as ambient 10 C can be selected this requires open damper and no additional heat in unit Table 13 2 Technical Data OGS and OMS Series 208 240 V Table top ovens Parameter Unit OGS 100 OGS 180 OMS 100 OMS 180 Process Work Space Atmosphere Min C F 50 122 50 122 50 122 50 122 Max C F 250 482 250 482 250 482 250 482 Temperature deviation K 4 5 4 0 4 5 4 0 3 0 2 5 43 5 3 0 from set value at 150 C 302 F spatial Max value Typical value Temperature deviation K 0 4 0 5 0 4 0 3 0 3 from set value at 150 C 302 F over time Max value Typical value Heat up time work space min 25 25 20 20 unoccupied from 25 C 77 F to 98 of set temperature of 150 C 302 F Recovery time work min 10 6 9 6 7 6 8 6 space unoccupied door open for 30 s to set temperature Max value Typical value Heat dissipation to Ww 26121096 32021096 459 10 513 10 environment at set temperature of 150 C 302 F and room temperature of 25 C 77 F Max air change at n 16 18 61 31 150 C 302 F Overall dimensions Height mm in 820 920 820 920 32 3 36 2 323 962 mm in 640 640 640 640 igi 252 252 252 252 Depth mm in 565 738 565 738 252 29 1 252 291 Overall weight kg lbs 53 117 66 146 53 117 66 146 Loading capacity Thermo Scientific Heratherm 13 3 Technical Data Table 13
31. at the installation and supply connections remain freely accessible The specified side clearances represent minimum distances 3 4 Heratherm Thermo Scientific Installation Space Requirement Table top ovens Figure 3 1 Table top ovens OGS 60 OGS 100 OGS 180 dimensions and required clearances Table 3 1 Heratherm Oven Dimensions Type A mm inch B mm inch OGS 60 OMS 60 530 20 8 OGS 100 OMS 100 640 25 2 OGS 180 OMS 180 640 25 2 C mm inch D mm inch 565 25 2 720 28 3 540 21 3 565 25 2 820 32 3 650 25 6 738 29 1 920 36 2 650 25 6 Dimensions in inches are rounded equivalents specified for information only Depth of handle display 66 mm 2 6 in not included in overall depth specified height of adjustable feet 36 mm 1 4 in not included in overall height specified Table 3 2 Required Clearances E mm inch F mm inch G mm inch H mm inch 80 3 2 50 2 300 12 300 12 Thermo Scientific Heratherm 3 5 Installation Space Requirement Floor Stand Ovens 400 liter units Figure 3 2 Floor stand ovens OGS 400 dimensions and required clearances Table 3 3 Oven Dimensions Model A mm inch B mm inch C mm inch D mm inch OGS 400 755 29 7 770 30 3 1655 65 2 810 31 9 e Depth of handle display 66 mm 2 6 in not included in overall depth specified Width of hinge 23 mm not included in overall width Table 3 4 Required Clearances E mm inch
32. ators and heating amp drying oven 50127477 Temperatur limiter for OMH OMH S OGH OGH S 50127480 Door hook catch for Heratherm incubators and heating amp drying ovens with a door stop on the right side 50127481 Door hook catch for Heratherm incubators and heating amp drying ovens with a door stop on the left side 50127482 Magnetic door hook catch for Heratherm incubators and heating amp drying ovens with a door stop on the right side 50127483 Magnetic door hook catch for Heratherm incubators and heating amp drying ovens with a door stop on the left sid 50127499 Heating coils for Heratherm OGS 60 OGH 60 OGH S 60 at a voltage of 120V 50127500 Heating coils for Heratherm OGS 60 OGH 60 OGH S 60 at a voltage of 230V 50127502 Heating coils for Heratherm OGS 100 OGH 100 OGH S 100 at a voltage between 208 and 240 V 50127503 Heating coils for Heratherm OGS 180 OGH 180 OGH S 180 at a voltage between 208 and 240 V 50127504 Heating coils for Heratherm OMS 60 OMH 60 OMH S 60 at a voltage of 120V 50127509 Kit fan system Heratherm OMS 60 120 V 50127510 Kit fan system Heratherm OMS 100 and OMS 180 208 240 V Heratherm Thermo Scientific Material No 50127511 Spare Parts and Accessories Description Kit fan system Heratherm IMH 60 IMH S 60 OMH 60 and OMH S 60 IMH 100 IMH S 100 IMH 180 and OMH S 180 120 V 50127512 Kit fan system Heratherm OMH 100 OMH S 100 IMH 180 IMH S 100 and OMH 180 208 240 V
33. castors 400 750 HTM 50134334 Kit shelf rack set cpl HTM 400 750 50135043 Kit electric insert cpl HTM H floorstand 50135044 Kit electric insert cpl HTM S floorstand 50135055 Kit electric insert cpl HTM 3 PH floor 50135058 Kit door lock 750 left cpl HTM 50135059 Kit door lock 750 right cpl HTM 50135060 Door outer casing left HTM 400 50135061 Door outer casing right HTM 400 50135062 Door outer casing left HTM 750 50135063 Door outer casing right HTM 750 30135151 Kit temperature sensor cpl HTM ovens floor 50135152 Kit overtemperature cut off HTM ovens 350 floor 50135153 Kit door lock 400 right cpl HTM 50135154 Kit door lock 400 left cpl HTM Thermo Scientific Heratherm 14 5 Spare Parts and Accessories 14 6 Heratherm Thermo Scientific Mm Device Log Oven type Part number Serial number Service number Location Operator s note Work carried out Notes Date Signature Thermo Scientific Heratherm 15 1 Device Log 15 2 Heratherm Thermo Scientific LLL Em Contact Overview of Thermo Fisher International Sales Organization Postal address USA Thermo Scientific 275 Aiken Road Asheville NC 28804 USA Enquiries from USA Canada Sales 1 866 984 3766 Service 1 800 438 4851 Enquiries from Latin America Sales 1 866 984 3766 Service 1 866 984 3766 Enquiries from Asia China Sales 86
34. de wall so that the rail is positioned over the two embossings at 5 and 2 Thermo Electron LED GmbH Heratherm 5 3 Start up Table top ovens 2 Clamp the retaining spring 3 behind the upper embossing 1 3 To remove the support rails pull the retaining spring tab down out of the embossing and remove the support rail assembly Installing and Uninstalling the Rear Air Baffle OMS Series only Heratherm OMS Series ovens are shipped from the factory with an air baffle readily pre installed at the back wall of the work space while OGS Series ovens do not have this feature Before the air baffle can be removed from the back wall the support rails need to be uninstalled as explained further above D000000000 Figure 5 5 Installing the Rear Air Baffle 1 Losen the two screws 1 that hold the air baffle to the back wall of the work space wanNING Risk of damage to sensor To prevent accidental damage be sure to avoid collision with the sensor when installing or uninstalling panels in the oven s workspace 2 Grab the two retaining springs 2 at their tabs and pull them downwards out of the embossings then pull off the rear air baffle 3 For the rear air baffle to install correctly the two retaining springs 2 must be facing upwards Place the air baffle on the lower embossings and tilt it upwards against the back wall of the work space 4 Clamp the two retaining springs 2 into the upper embo
35. drying ovens 50127448 Temperature sensor for Heratherm heating amp drying ovens 50127450 Upper door hinge for Heratherm incubators and heating amp drying ovens 50127451 Lower door hinge for Heratherm incubators and heating amp drying ovens Thermo Scientific Heratherm 14 1 Spare Parts and Accessories 14 2 Material No Description 50127455 Outer door for Heratherm IGS 100 IMH 100 IMH S 100 OMS 100 OMH 100 OMH S 100 OGS 100 OGH 100 and OGH S 100 with a door stop on the right side 50127456 Outer door for Heratherm IGS 180 IMH 180 IMH S 180 OMS 180 OMH 180 OMH S 180 OGS 180 OGH 180 and OGH S 180 with a door stop on the right side 50127457 Kit operating panel Heratherm General Protocol incubators and heating amp drying ovens 50127458 Kit operating panel Heratherm Advanced Protocol and Advanced Protocol Security incubators and heating amp drying ovens 50127461 Kit electronic insert Heratherm General Protocol incubators and heating amp drying ovens without main board fan 50127462 Kit electronic insert Heratherm Advanced Protocol and Advanced Protocol Security incubators and heating amp drying ovens without main board fan 50127463 Mainboard cable for Heratherm incubators and heating amp drying ovens 50127469 Door switch for the right side of Heratherm incubators and heating amp drying ovens 50127470 Door switch for the left side of Heratherm incub
36. e 10 1 Door seal replacement example showing OMH Series oven sse 10 4 Thermo Scientific Heratherm i List of Figures ii Heratherm Thermo Scientific ow Safety Notes Basic Operating Precautions These operating instructions describe Heratherm ovens Heratherm ovens have been manufactured to the latest state of the art and been tested thoroughly for flawless functioning prior to shipping However the oven may present potential hazards particularly if it is operated by inadequately trained personnel or if it is not used in accordance with the intended purpose Therefore the following must be observed for the sake of accident prevention Heratherm ovens must be operated by adequately trained and authorized professional personnel Heratherm ovens must not be operated unless these operating instructions have been fully read and understood The present operating instructions applicable safety data sheets plant hygiene guidelines and the corresponding technical rules issued by the operator shall be used to create written procedures targeted at personnel working with the subject matter device detailing the safety precautions to be taken when processing specific agents the measures to be taken in case of accidents Repair work on the oven must be carried out only by trained and authorized expert personnel The contents of these operating instructions are subject to change at any time withou
37. er 3 de eee voi ende dee leer diei ecabaneadebantes 5 12 COSTAE I ears cea RL et cata a cated ces meddle ea dae 6 1 Preparing the venas desee ada aesti apu este folebat pas Nereus 6 1 Starting Operation eedem ee Rete eH OR BIA nE He eei OR EE 6 1 Handling and GoHltrol zeit rice ee dae ashi oro npo cea ees secu na nie iU ee celeste eam 7 1 Powering lUpi is etie auetoritate S 7 5 Switching the Oven Off Powering DOS fs topi ait ctiaclit dona i Ded aed Aat ute eibtr iul iva tud ecd ti sepd 7 5 Temperature Set Vli cura dee cQ biet apt te wot es ane dig ther i etd tn i a 7 6 Merl EUN 7 7 Stopping a T3meto aon o ee OUR ROI Gp a aaa 7 8 SD EUREN 7 9 EEOP L99 3er arbe ib enu ui eus 7 9 Cali DEAUOTIssuottenat tU deti ole teh borde loca Met dd te UMS D MEE 7 10 Temperature Display Unitas akesi eaae orrore aeree uico theses cHap uides Ra A sa dud above n lua pian 7 11 Configura ON s oreet oed Aci ipia ati beu p bets PED oL Oe DM UR Doc ales Dres gts eor eanit Siak 7 12 Jine uem 8 1 Shutting th Oven DOWN sssi sessie rin een entities hides Bak e E S EO eL earr ees ind px ide Lau 8 1 ii Heratherm Thermo Scientific Contents Chapter 9 Cleaning and Disinfection eeeeeeeeeeeeeeeeeeeeeee eene nennen nnne n nnnm nnmnnn nnna 9 1 CNS UG A oantacibu c s E ai pacte cab eb pla epus lees dios o aue toc oa in lace ande pacd 9 1 Cleaning exterior SUutfaees toto opt e eete coeleste eE ae neue Ul ur Celia Qe P Duen GE RO enta derau RN RIVA UR
38. ersonnel only The connection to the building must be carried out with appropriate screws and dowels according to the consistence of the building part Thermo Scientific Heratherm 3 13 Installation Floor stand unit spacers Additionally the following caution notes must be heeded at all times A CAUTION Risk of overheating with stacked devices To avoid the risk of electrical components and the outer enclosure overheating or temperature control failing due to insufficient ventilation do not exceed the specified stacking height A CAUTION Risk of tipping and dropping of stacked devices You should be aware at all times that stacked devices do not form a stable unit even when the stacking pads and frames are used correctly The top device may tip over and drop down when being transported in a stack To avoid injury to persons and damage to equipment do not attempt to move stacked devices as a unit Separate and move each device one by one then restack them Thermo Scientific accepts no responsibility or liability whatsoever with regard to stacked third party devices this is at the user s own risk Floor stand unit spacers The spacer on the electrical module must be pulled out and fixed in place before installing the floor stand unit at its installation location 1 Loosen the 2 screws 2 Pull out the spacer and slide the screws into the recesses 3 Tighten the two screws 3 14 Heratherm Thermo Scientific o Product
39. esh Shelves Figure 5 13 Wire mesh shelf 1 Push the wire mesh shelf onto the shelf support brackets with the tilt protection devices 1 facing the rear panel of the oven The tilt protection devices 1 also serve as guides for the wire mesh shelves 2 Slightly raise the wire mesh shelf so that the pull out stops 2 can slide over the shelf support brackets 3 Make sure that the shelves and both of their tilt protection devices are free to move over the shelf support brackets Levelling the Table top ovens 1 Position a bubble level onto the center shelf 2 Manually adjust the levelling feet until the wire mesh shelf is horizontally aligned in all directions Perform the adjustment of the levelling feet from left to right and from rear to front Thermo Electron LED GmbH Heratherm 5 9 Start up Mains Connection Mains Connection Contact with live electrical components may cause a lethal electric shock Before connecting the oven to the power supply check the power cord and the plug for damage Do not use damaged cables for connecting the oven to the power supply The oven has a class I protection earthed enclosure To minimize the risk of electrical shock use the AC power cord supplied to connect the oven to a correctly installed and protection earthed power supply source with the following features in place for each oven T 16 A slow blow fusing e B 16 circuit breaker N
40. ess to activate the menu bar then use 122 to select the Timer icon and press to confirm The word Off appears in the multifunctional display pane Thermo Scientific Heratherm 7 7 Handling and Control Timer Table 7 7 Setting a Countdown type On Timer Press to select the On timer option and confirm the selection with C23 Set the hours and minutes until the oven is supposed to turn on by pressing 22 or B then press to confirm The oven switches off The display goes out the Timer icon is illuminated in the menu bar with a hand rotating on its face Additionally the readiness indicator icon is illuminated Stopping a Timer Table 7 8 Stopping an Off Timer Before It Expires Press to activate the menu bar then use 122 to select the Timer icon and press to confirm Confirm the OFF by pressing then press E to return to the main menu In the menu bar the Timer icon g will go out The display returns to its default mode Table 7 9 Stopping an On Timer Before It Expires To cancel a pre programmed on timer while the oven is switched off hold the On Off button depressed for a few seconds In the menu bar the Timer icon ol will go out The display returns to its default mode 7 8 Heratherm Thermo Scientific Handling and Control Settings Settings The Settings menu item opens a submenu populated with variou
41. everal devices are to be placed in the same room additional ventilation may have to be provided as necessary To avoid any impact of the heat dissipated by the oven on the ambient climate the room must be vented by means of a laboratory grade ventilation system that complies with applicable local and national health and safety regulations and has sufficient capacity f excessive temperatures tend to occur in the operating room be sure to provide a thermal protection means that cuts out the power supply to mitigate the impact of overtemperature scenarios Use with Air Exhaust Systems When the oven is connected to an air exhaust system be sure to adjust its air flow so the temperature distribution pattern throughout the oven s workspace remains unchanged and precision temperature control is maintained Also be sure to interlock the oven and its exhaust system so both start and run at the same time The oven may be unable to overcome the extra flow resistance introduced by the idle air exhaust system which may cause the exhaust air to be vented into the surrounding lab room Before using existing piping in the building to exhaust hot air from the oven be sure that such exhaust piping is made of heat resistant material so it will not overheat melt and or cause a fire The ovens outer surfaces and its air exhaust piping may become hot so be sure to maintain the proper spacing from walls and ceilings specified by local building codes and
42. explosion or fire Ts refrain from loading the oven with any of the substances listed in the section Incorrect Use on page 1 5 make sure that the ambient air is free of any solvents do not operate the oven in areas with an explosion hazard 4 Load the work space with samples Risk of overloading Overloading may damage the shelves or cause the shelves and or the oven to tilt when the shelves are being drawn out ultimately destroying the samples To avoid overloading the oven or its shelving be sure to observe the sample weight limits specified in see Technical Data on page 13 1 Hot surfaces After opening the door this may swing back automatically The interior panel of the outer door as well as the surfaces of the outer housing the shelving and the work space become extremely hot while the oven runs through its heating cycles When removing samples from a running or recently completed heating cycle always wear safety gloves and other appropriate personal protection equipment to avoid burns on hot surfaces NO TE Proper loading To ensure sufficient air circulation and uniform heating of the samples do not use more than 70 of the maximum surface area of the work space Bulky objects in the work space that dissipate heat may impair heat distribution 6 2 Heratherm Thermo Scientific MEN UN Handling and Control Heratherm OGS Series and OMS Series ove
43. g and Control Settings Table 7 10 Reading the Error Log Press to go to the next entry or to go back to the previous one After reaching the entry numbered 22 the display wraps and returns to the beginning of the error log that is to entry number E01 To exit from the error log and return to normal display mode press J twice The Settings icon in the menu bar will go out Calibration The Settings gt Calibration menu item enables the user to initiate a temperature calibration routine for the built in temperature sensors and choose whether calibration should be accomplished manually or automatically The Manual option allows for entering an absolute temperature directly as measured for example using an external reference sensor N Q TE Calibration Prerequisites Maintain the ambient conditions within the specified limits of the oven and make sure that the damper is fully closed before launching calibration Varying ambient conditions and or an open damper may impact the result of the calibration routine which may lead to misadjustment of the controller and unreliable temperature control operation Table 7 11 Entering the Calibration Reference Temperature Manually Press to activate the menu bar then use or to select the Settings icon and press ES io confirm Press to switch to the CAL ibration menu item 7 10 Heratherm Thermo Scientific
44. ght Devices that produce excessive amounts of heat must not be placed near the oven To avoid drying operation without an appropriate fresh air supply make sure that the air inlet which may be equipped with an optional fresh air filter is not obstructed or blocked by any adjacent objects Power line voltage variations must not exceed 10 of the nominal voltage Transient overvoltages must not exceed the values usually encountered throughout the power supply network The nominal transient overvoltage level shall be the surge withstand voltage according to overvoltage category II of IEC 60364 4 443 Place the oven on a floor stand option to be ordered separately never on the lab floor Consider installing one dedicated upstream circuit breaker per oven to avoid multiple device failures in case of an electrical fault Intermediate Storage When the oven is placed in intermediate storage which is permissible for a maximum of four weeks make sure that the ambient temperature is between 20 C to 60 C 68 F to 140 F and the maximum relative humidity does not exceed 90 non condensing 3 2 Heratherm Thermo Scientific Installation Room Ventilation Room Ventilation Heat dissipating from the oven during continuous operation may cause a change in the room climate Therefore the oven must only be installed in rooms with sufficient ventilation Do not install the oven in room recesses without ventilation When s
45. h serious injuries or damage to the oven and other equipment use spare parts approved by Thermo Electron LED GmbH only Third party spares without approval void the limited warranty Do not modify the oven in any way without obtaining the prior written authorization from Thermo Electron LED GmbH Unauthorized modifications may compromise operational safety and give rise to hazards that may result in death serious injuries or damage to the oven and other equipment Service Intervals During ongoing operation the following service work must be performed Annual service Have the oven inspected and serviced by an authorized Technical Service agent N TE Service contract Thermo Electron LED GmbH offer a product specific service contract comprising all necessary tests and service work Preparing Temperature Calibration To determine the exact measured value of the oven s integral temperature sensor a temperature comparison measurement must be performed every three months If a major temperature deviation is found during this check temperature calibration is required During this process the temperature controller of the oven is set to the value measured during the temperature comparison measurement Use a calibrated measuring instrument with an accuracy of 1 C 1 7 F for this test 10 2 Heratherm Thermo Scientific Maintenance Comparison Measurement Procedure To minimize temperature va
46. hange without notice All technical information in this document is for reference purposes only System configurations and specifications in this document supersede all previous information received by the purchaser Thermo Fisher Scientific Inc makes no representations that this document is complete accurate or error free and assumes no responsibility and will not be liable for any errors omissions damage or loss that might result from any use of this document even if the information in the document is followed properly This document is not part of any sales contract between Thermo Fisher Scientific Inc and a purchaser This document shall in no way govern or modify any Terms and Conditions of Sale which Terms and Conditions of Sale shall govern all conflicting information between the two documents Oo M Contents Chapter 1 Safety 1 1 Basic Operating Precautions vies orn e br i e e D di a ne re er ii RE 1 1 Op r tional Safety Rules P nXe 1 2 huc E EEE TEE T m 1 2 Explanation of Safety Information and Symbols s sssssesseeesesesseseersrrssrsrsrsresrsrsrsrestsrsrsretsersrsrereseeeess 1 3 Safety Notes and Symbols Used Throughout These Operating Instructions eee 1 3 Additional Symbols for Safety Lita ia OB aiio testes br quado a cue ticis Pap tip abed en luce a M obit 1 4 Symbols on the Oven gos cete eoe per a R
47. i cece came M et Seca ci ein SD Cdi Sorte Boss ue Uode ace 13 1 Chapter 14 Spare Parts and Accessories eeeeeeeeeeseeeeeeeeeeeee eene nennen nnne nnne nnne nnne 14 1 Chapter 15 Device Log osito iii tiat ribus Qvae vtta tu MIU vae Loi Ca CLE CAR ENA dri i Did tea aa dude Ue dva CA 15 1 Chapter 16 ere ojric mem daai 16 1 Thermo Scientific Heratherm iii Contents iv Heratherm Thermo Scientific o List of Figures Figure 3 1 Table top ovens OGS 60 OGS 100 OGS 180 dimensions and required clearances 3 5 Figure 3 2 Floor stand ovens OGS 400 dimensions and required clearances sss 3 6 Figure 3 3 Floor stand ovens OGS 750 dimensions and required clearances sess 3 7 Figure 3 4 Lift DOES as medici terii hace hme sa EEE xc sinat ci cmn wa uas roses xc Ges out defen en Rubi B EE buta 3 8 Figure 4 1 Heratherm OGS 60 OGS 100 OGS 180 Series Front View seeeeeeeeeeeeeeenen 4 2 Figure 4 2 Heratherm OGS 60 OGS 100 OGS 180 Series Rear View sscccssncssessssussteanesosstsnssnsiacynausencuaniesstones 4 3 Figure 4 3 Heratherm OGS 400 Series Front View pats axes eairinied eund piv RE D D p dpra as eiiim aUis duod pa 4 4 Figure 4 4 Heratherm OGS 400 Series Rear VIEN uscire pr reirkgost ier iR UI TR hei Y Me nsa e Rer vei p M Re rpa vU PU gh 4 5 Figure 4 5 Heratherm OG
48. ic Contact Thermo Scientific Heratherm 16 3 Part of Thermo Fisher Scientific SCIENTIFIC
49. ing cap for side panel mounted tube access port Once the cables tubes or other conduits have been inserted the tube access ports must be padded with the heat resistant fiber pads shipped with the device and the cap must be mounted to seal the port as far as possible A WARNING Risk of Burning on Hot Surface The surface around the tube access ports may become extremely hot 4 16 Heratherm Thermo Scientific LLL m Start up Installing the Shelf System of the table top ovens The installation of the shelf system does not require any tools The support rails are secured in place by spring action Once the shelf support brackets have been inserted into the rails the wire mesh shelves can be simply pushed onto their support hooks to complete the installation The support rails of the floor stand ovens cannot be removed Initial installation Heratherm OGS Series ovens have the shelving support rails integrated with the air baffles which are readily pre installed when the devices are shipped from the factory Heratherm OMS Series ovens come with separate support rails which need to be installed as follows 1 Peel off the protective foil from the support rails 2 Push the retaining spring 1 into the guide on the support rail 2 making sure that the locking nub 3 on the retaining spring safely engages with the matching hole in the support rail i Figure 5 1 Sliding the Retai
50. ivated message shown on dis play Overheat protection activated to prevent destruction of the samples Audible alarm returns upon acknowledgement Switch off the device and call service Temperature Too High E111 The actual measured value exceeds the upper limit of the permissible error range May occur when the user lowers the set point tem perature on a hot oven but leaves the door closed Audible alarm activated message shown on dis play Heater turned off until upper limit of hysteresis is recovered Servo control operations continue Alarm can be acknowledged and goes away when the differ ence between the actual and set values ceases to exist Note This error does not indicate a defective triac Open the door to speed up cool down Check whether the device was loaded with a hot object if so remove Ensure that the equipment was operated with at least one perforated shelve and with the door not opened longer than 10 min If this doesn t solve the problem call service Sensor Error E112 Unsuitable sample load or possible damage to refer ence sensor The mea sured actual value is out of range Audible alarm activated message shown on dis play Control continues on process sensor If both sensors are defective all control circuits will be dis abled Check whether device was loaded with an unsuitable object If error does not go away call service power up
51. l 16 2x16 18 65 32 90 80 non condensing 20 68 60 140 90 non condensing 52 52 2000 2187 50 2 690 27 2 80 3 2 814 32 200 8 300 12 Thermo Scientific Technical Data 1 Temperatures as low as ambient 10 C can be selected this requires open damper and no additional heat in unit Table 13 3 Technical Data OGS Series Floor stand ovens Parameter Process Work Space Atmosphere Min Max Temperature deviation from set value at 150 C 302 F spatial Max value Typical value Temperature deviation from set value at 150 C 302 F over time Heat up time work space unoccupied from 25 C 77 F to 98 of set temperature of 150 C 302 F Recovery time work space unoccupied door open for 30 s to set temperature Max value Typical value Heat dissipation to environment at set temperature of 150 C 302 F and room temperature of 25 C 77 F Max air changes at 150 C 302 F Overall dimensions Height with casters Width Depth Overall weight Loading capacity per shelf Max overall loading capacity per device Electrical data Power rating Max Current Earthing system e g 1 N PE Power line frequency Power line voltage 10 96 IP protection system Protection class Thermo Scientific Unit CIF CIF min min m mmin mmin mmp in kg lbs kg lbs kg lbs Hz OGS 400 OGS 750 50 C 122 F 250 C 482 F 3 0
52. lashing in the display pane The factory default setting is F Press or to switch to the desired temperature unit and confirm the selection with ee The temperature unit to the right of the temperature display field item D1 in figure 7 1 on page 7 1 has changed according to your selection The display returns to its default mode The Settings icon in the menu bar will go out Configuration The Settings gt Configuration menu item enables the user to enter a four digit code that loads a specific set of operating parameters for the oven for example in order to make the voltage selection described in the section Connecting the RS 232 Interface on page 5 12 only for 100 and 180 liter units Table 7 13 Entering the Four digit Code Press to activate the menu bar then use 2 or ENU to select the Settings icon and press to confirm gt D uu Leo Press to switch to the ConF iguration menu item The word ConF will be flashing in the multifunctional display pane Press the button 7 12 Heratherm Thermo Scientific Handling and Control Settings Table 7 13 Entering the Four digit Code The multifunctional display pane will present a prompt similar to the example shown at left with the first digit of the four digit configuration code flashing Set the first digit of the configuration code using or 1223 and confirm your setting with ca Set
53. mation regarding the application Thermo Electron LED GmbH Heratherm 1 3 Safety Notes Explanation of Safety Information and Symbols Additional Symbols for Safety Information 1 4 Wear safety gloves Wear safety goggles Harmful liquids Electric shock Hot surfaces Fire hazard Explosion hazard Suffocation hazard P 9 i e ie Er D n Danger of tipping Heratherm Thermo Electron LED GmbH Safety Notes Intended use of the device Symbols on the Oven A Observe operating instructions p Mark of conformity USA Canada C US 120 Volts AC power socket 60 devices only Intended use of the device Correct Use Heratherm ovens are laboratory devices for heating applications equipped with precision temperature control They are designed for heat treating samples or materials at operating temperatures between 50 C 122 F and 250 C 482 F including for example drying ageing analyzing decomposing burn in oxidizing reducing and preheating Heratherm ovens have been designed for installation and operation in the following environments heat treatment drying of material Incorrect Use To avoid the risk of explosion do not load the oven with tissue material or liquids that are easily flammable or explosive release vapor or dust that forms combustible or explosive mixtures when exposed to air
54. meplate and acknowledge the error Sensor Error E100 Process sensor damaged Audible alarm activated Call service The actual measured value message shown on dis is out of range play Control transferred to reference sensor If both sensors are defective dis able all control circuits Temperature Too High Actual measured value Process protection acti Call service Temperature Not Plau sible E103 The difference between the control and reference sen sors exceeds the maximum permissible deviation ren dering the measurement implausible Device uses the sensor that indicates the higher temperature for servo con trol Audible alarm acti vated message shown on display Error can be acknowledged and doesn t reset If the problem does not go away call service Calibration Value Too High E104 The calibration reference value calculated on the basis of the user input falls short of the upper limit for calibration references Fallback to previous cali bration reference Audible alarm activated message shown on display Check the external refer ence sensor for proper function and replace if necessary If this does not solve the problem call ser vice Calibration Value Too low E105 The calibration reference value calculated on the basis of the user input exceeds the lower limit for calibration references Fall back to previous cali bration reference Audible alarm activated mes
55. minal Commands for Querying Data Command Syntax Response Example Temperature Set Value T1 Current Work Space Temperature T2 Reference Temperature T3 Sample Sensor Temperature T4 3010 00 c2 1 3010 1f 125 00 124 96 000 000 000 00 b0 T1 T2 T3 T4 5 14 Heratherm Thermo Electron LED GmbH EN BE Operation Preparing the Oven The oven must not be released for operation before all major start up activities have been completed see Start up on page 5 1 Device Check Prior to starting operation the following oven components must be checked for their correct function The door seal in the front frame must not be damaged The shelving components must be installed safely Disinfecting the Oven s Work Space Disinfect the work space according to the operator specified hygiene guidelines Starting Operation 1 Turn the oven on using the control panel 2 Adjust the temperature set value on the control panel 3 The temperature controller starts adjusting the work space to the user specified temperature set value now Upon initial installation and subsequent heat up this appliance may produce an odor and trace evolution of non toxic vapor that results from brake out of the insulation binder This condition is normal for factory new products and will diminish with continued operation Thermo Scientific Heratherm 6 1 Operation Starting Operation y To avoid any risk of
56. mm 50126665 Stacking adapter Heratherm 60L 50126666 Stacking adapter Heratherm 100L 50126667 Stacking adapter Heratherm 180L 50127431 Outer door for Heratherm IGS 60 IMH 60 IMH S 60 OMS 60 OMH 60 OMH S 60 OGS 60 OGH 60 and OGH S 60 with a door stop on the left side 50127432 Outer door for Heratherm IGS 100 IMH 100 IMH S 100 OMS 100 OMH 100 OMH S 100 OGS 100 OGH 100 and OGH S 100 with a door stop on the left side 50127433 Outer door for Heratherm IGS 180 IMH 180 IMH S 180 OMS 180 OMH 180 OMH S 180 OGS 180 OGH 180 and OGH S 180 with a door stop on the left side 50127434 Outer door for Heratherm IGS 60 IMH 60 IMH S 60 OMS 60 OMH 60 OMH S 60 OGS 60 OGH 60 and OGH S 60 with a door stop on the right side 50127435 Staple feet Heratherm incubators and heating amp drying ovens 50127436 Kit door seal for Heratherm 60L 50127437 Kit door seal for Heratherm 100L 50127438 Kit door seal for Heratherm 180L 50127439 Kit door clips for Heratherm 60L 100L 180 L 50127443 Levelling feet for Heratherm incubators and heating amp drying ovens 50127444 Kit door handle right Heratherm incubators and heating amp drying ovens 50127445 Kit door handle left Heratherm incubators and heating amp drying ovens 50127446 Kit door handle with lock right Heratherm incubators and heating amp drying ovens 50127447 Kit door handle with lock left Heratherm incubators and heating amp
57. mmunication has been established successfully enter any of the commands listed in table 5 2 below depending on what type of information you want to query 8 Use the following generic command syntax aaaa bb cc lt CR gt where identifies the command line as a query aaaa is the parameter address bb is a query that must be left at 00 for technical reasons cc is for a command specific checksum listed in the table below CR is for carriage return You will receive a response of the following general format aaaa bb XXXXX cc lt CR gt where t identifies the line as a response to a query aaaa is the parameter address entered with the query bb is the number of payload bytes in hexadecimal code for example 1F for the decimal value 31 XXXXXX is the significant status information queried cc is a check sum technically an inverted XOR of all bytes returned excluding the check sum bytes and the CR character CRo is for carriage return Table 5 2 Terminal Commands for Querying Data Command Syntax Combined Date and Time Response Example 0010 00 c1 1 0010 11 31 07 10 01 02 23 e2 Date Time Date only 0011 00 c0 1 0011 08 31 07 10 d2 Date Time only 0012 00 c3 1 0012 08 01 02 23 dc Time Thermo Electron LED GmbH Heratherm 5 13 Start up Connecting the RS 232 Interface Table 5 2 Ter
58. mperature too high appears in the display window and an audible alarm is sounded When the user acknowledges the error message the red alarm icon D3 in figure 7 1 on page 7 1 is illuminated and the Temperature Set Value icon see table 7 3 on page 7 3 is highlighted by a red border to indicate that thermal protection has kicked in Data Communications amp Alarm Interface All signal connections are installed in the electrical interface panel at the rear of the oven RS 232 Interface The RS 232 interface left in figure 4 11 below may be used to connect ovens to the serial interface port of a computer to allow for the computer aided acquisition and documentation of major operating parameters temperature error codes etc Figure 4 11 Signal Interfaces and Power Socket AC Power Socket The oven is connected to the AC supply mains via the socket at right in figure 4 11 above which accepts a power cord with an IEC standard plug 9 4 12 Heratherm Thermo Scientific Product Description Work Space Components Fuses Two 16 A slow blow fuses mounted on the oven s main electronic circuit board protect internal circuitry from the impact of excessive power consumption Replacement should only be carried out by skilled and authorized qualified personnel of electrotechnology signal engineering N O E Fuse replacement The device fuses are not user serviceable When the oven exhibits the typical signs of a blown fuse no
59. n 30 seconds in any selected menu item the display exits from the selected screen and returns to default display mode 7 4 Heratherm Thermo Scientific Handling and Control Powering Up Powering Up 1 Plug the power plug of the oven into a suitable protection earthed AC power outlet In the display window on the front panel the readiness indicator icon top right item at D3 in figure 7 1 on page 7 1 is illuminated Keep the On Off button depressed for two seconds An initialization routine will be run after the oven has been powered up Once initialization has been completed the display will light up and the current work space temperature will appear in the temperature display pane item D1 in figure 7 1 on page 7 1 The oven is ready for use now Switching the Oven Off Powering Down Thermo Scientific 1 Keep the On Off button depressed for two seconds The display window goes out except for the readiness indicator icon rightmost icon in the top right item at D3 in figure 7 1 on page 7 1 and a residual heat temperature readout in case the work space temperature is still higher than 50 C 122 F The oven is switched off now 2 If required unplug the AC power plug to power down the oven completely Heratherm 7 5 Handling and Control Temperature Set Value 7 6 Temperature Set Value Heratherm ovens allow for setting the desired work space temperature directly using only a few b
60. ning Spring into the Support Rail Thermo Electron LED GmbH Heratherm 5 1 Start up Installing the Shelving Installing the Shelving The illustrations below show the placement of the shelf system elements R E f 0 i j i i Retaining spring Air baffle lateral Shelf support Wire mesh shelf Air baffle bottom Figure 5 2 OGS Series Installing the Shelving Retaining spring Air baffle rear Wire mesh shelf Support Rail igure 5 3 OMS Series Installing the Shelving 1 2 3 Shelf support 4 5 mn 5 2 Heratherm Thermo Electron LED GmbH Start up Preparing the Work Space Preparing the Work Space The following work space components should be checked for cleanliness and cleaned prior to use shelf support brackets wire mesh shelves work space surfaces work space seals and gaskets For details about the cleaning of the oven please refer to the section Cleaning on page 9 1 Table top ovens Installation or Removal of the Support Rails OMS Series only Figure 5 4 Support Rail Installation The embossings at 2 and 5 act as lateral guides for the support rails while the embossings at 1 and 6 secure the support rails in place For the support rails to install correctly the retaining spring 3 must be facing upwards 1 Place the support rail 4 on the lower embossing 6 and tilt it upwards against the work space si
61. ns come with a front panel mounted control unit consisting of a multifunctional display four control buttons and an on off button The four control buttons interact with the display window to let users access all of the user control functions and adjustments of the oven including for example the temperature set value timer as well as a variety of other functions Under normal operating conditions the display presents user with the work space temperature The display returns to its default mode upon completion of the adjustments or whenever no entries have been made for a period of 30 seconds The graphic below shows the Heratherm OGS 60 100 180 400 750 and Heratherm OMS 60 100 180 control panel with all of its visualization elements and controls Figure 7 1 Control Panel for Heratherm OGS Series and OMS Series ovens D3 D1 D2 K1 K2 K4 K3 K5 The table below contains brief descriptions of the buttons on the control panel items K1 through K5 in figure 7 1 Thermo Scientific Heratherm 7 1 Handling and Control 7 2 Table 7 1 Control Buttons Icon Item Function Tem K1 Menu Enter button First key press Activates the menu highlighting the first menu item with a red border Second key press Selects the currently activated menu item as highlighted by the red border At the same time pressing this button enables entries with item D1 Third key press once a setting has been changed Confirms a previous entry o
62. on Temperature Set Value Allows for changing the temperature set value within the permissible tem perature range The set value can be changed by pressing the Left and Right item K2 or K4 and you can after confirming your changes with the Menu Enter button item K1 track the impact on the actual tempera ture in the display pane at DI Instructions Temperature Set Value on page 7 6 Timer Allows for having the oven turn on and or off upon expiry of a user speci fied countdown period When the user enables an on timer the oven goes out A rotating in the Timer icon and the illuminated readiness indi cator icon in the status display area indicates that the timer is running Instructions Timer on page 7 7 Settings Invokes a submenu with the following functions Read access to error log Calibrating the oven Toggling the temperature display unit between C and F Entering a configuration control code Instructions Settings on page 7 9 Thermo Scientific Heratherm 7 3 Handling and Control Table 7 3 Menu Bar Icons Icon Function Readiness Indicator Illuminated when the oven has been switched off using the On Off button item K3 in figure 7 1 Unlike other menu items this icon cannot be selected Instructions Switching the Oven Off Powering Down on page 7 5 N TE Button Inactivity Monitoring When no button is pressed for more tha
63. on the side opposite of the door hinges Bend the fixing tabs of the anti tilt anchor up on one side and down on the other by an angle of approx 90 1 Do not use this position if the door is hinged on this side Right hand hinges represent the standard configuration 2 Preferred position 3 Alternative position Do not use if the door is hinged on this side Remove the bracket screws Use the preferred position if possible Fix the anti tilt anchor with the bracket side down to the unit Position the unit with the anti tilt anchor to in an angle of approx 90 20 Take care that the stacking feet of the unit are still in correct place on the lower unit or on the stacking adapter Fix the anti tilt anchor to a solid part of the building 3 12 Heratherm Thermo Scientific Installation Installing the Anti tilt Anchor Floor stand ovens Anti tilt anchors Heratherm floor stand ovens must always be attached to the wall using two 2 retaining brackets on the outer left and right side on the back of the unit Remove the screws Attach the end of the retaining bracket that is facing downward to the unit Align the device at roughly 90 20 to the retaining bracket Affix the retaining bracket to the wall NCAUTION Unsafe part of the building Install the anti tilt anchor to a solid part of the building which is able for shoring loads The installation has to be carried out by qualified p
64. ool Printed circuit boards Coated electrical components contain various plastics materials Components mounted on circuit boards containing epoxy resin bonder Plastic components general see material labelling Exterior housing Galvanized steel sheet painted Oven rear panel Galvanized steel sheet Outer door Galvanized steel sheet painted Door inner panel OMS and OGS stainless steel 1 4016 Control panel and display window protective foil Polyethylene Heater Thermo Scientific Stainless steel sheathed resistance heater wires Heratherm 11 1 Disposal Overview of Materials Used 11 2 Component Interior containers installed compo nents and shelves Material Stainless steel 1 4016 and galvanized steel shelves are chrome plated Door frame seal Silicone Fan wheel Stainless steel 1 4016 OMS Series only Cables Plastic sheathed stranded copper wire Heratherm Packaging Corrugated board polyethylene film and styrofoam chemically untreated wood Thermo Scientific 12 Error Codes Table 12 1 below lists the error messages that may appear in the control panel display window see Error Log on page 7 9 and provides instructions for clearing such alarms Table 12 1 Heratherm Oven Error Codes Error Message amp Code Display Error E002 Root Cause Display communication error The built in control ler was unable to
65. ough K4 refer to the buttons shown in that figure Heratherm Thermo Scientific Handling and Control Table 7 2 Display Features Feature Item Function D1 Display pane showing a permanent readout of the actual tem perature in the work space either in C or F depending on the user s preferences see Toggling the Temperature Display Unit on page 7 11 A flashing time entry prompt of the general format hh mm hours minutes both with two digits appears in this place while the user is setting up a timer Upon occurrence of an error condition the current error code flashes in this area Additionally the red alarm icon at D3 flashes Menu bar with iconized representations of adjustable parame ters A red border is used to highlight the current menu item as selected using the Menu K1 and arrow buttons Left K2 and Right K4 Brief descriptions of the individual menu items are given in table 7 3 below Note Ifa menu item cannot be selected then the function it represents is not part of the equipment configuration of your unit D3 Alarm icon Upon occurence of an error condition the red alarm icon will be illuminated At the same time the current error code will flash in the display pane D1 The alarm may be acknowl edged by pressing the co button The table below contains brief descriptions of the menu bar icons item D2 in figure 7 1 Table 7 3 Menu Bar Icons Icon Functi
66. ploy the RS 232 command inventory listed in table 5 2 below for automating process data logging for example by embedding these commands in scripts that run on a remote computer NCAUTION RS 232 interface compatibility To avoid overloading and damaging the RS 232 interface check the interfacing parameters against the pin out description given above and make sure that computer s interface port works with a signal level of 5V DC Interconnecting the Oven with a Computer 1 Turn the computer off 2 Route the serial interface cable along a path that does not cross hot exhaust air piping tables aisles or passageways With stacked devices keep the serial interface cable away from hot spots on the other oven in the stack 3 Connect one connector of the serial interface cable cable length 5 to max 10 m not supplied as a standard item to the socket labeled RS 232 in the electrical interfaces section at the rear of the oven see Signal Interfaces and Power Socket on page 4 12 4 Connect the second connector to an unused COM 1 COM 2 or other serial port on the computer 5 Boot the computer 6 Launch our standard terminal rogram and set u the connection with the followin y prog p 8 parameters 57600 bits per second 8 data bits 5 12 Heratherm Thermo Electron LED GmbH stop bit No Parity Start up Connecting the RS 232 Interface 7 Once your terminal indicates that serial co
67. r selection K2 Left button After the first press of the Menu Enter button Moves the selection in the menu see item D2 to the next icon on the left Once a menu item has been selected Decreases an adjustable parameter value for example the temperature set value in D1 Holding this button depressed for a few seconds changes the selected value in quick run mode K3 On Off button Holding this button depressed for 2 seconds switches the oven off The display window goes out except for the readiness indi cator icon in the status display area at item D3 The temperature display pane D1 provides as dimmed readout of the work space temperature provided that the temperature exceeds 50 C 122 F SAT K4 Right button After the first press of Menu Enter button Moves the selection in the menu see item D2 to the next icon on the right Once a menu item has been selected Increases an adjustable parameter value for example the temperature set value in D1 Holding this button depressed for a few seconds changes the selected value in quick run mode K5 Escape button Returns to the previous level of the menu or standard display Upon exiting from the current menu item the user may be prompted to save any previously made settings The table below contains brief descriptions of the display features of the control panel items D1 through D3 in figure 7 1 the identifiers K1 thr
68. ral built in units in a row are connected to a central air exhaust system see illustration a draft interrupter should be installed Draft breaker N Air exhaust hose Air inlet pipe Fig 1 Fig 2 Thermo Scientific Heratherm 3 1 Installation Intermediate Storage The oven must only be operated in a location that meets all of the ambient condition requirements listed below Draft free and dry indoor location The dust burden may not exceed the contamination category 2 based on EN 61010 1 Using the oven in an atmosphere with electrically conductive dust is prohibited The minimal distance to adjacent surfaces must be observed on all sides see section Space Requirement on page 3 4 The operating room must be equipped with appropriate ventilation Solid level fire proof surface and no flammable materials opposite to the rear panel of the oven Vibration proof substructure floor stand lab table capable of bearing the dead weight of the oven and its accessories particularly if two devices are stacked The ovens have been designed for an operating height of up to 2000 m above sea level Ambient temperature range from 18 C to 32 C 64 4 F to 89 6 F Relative humidity up to 8096 maximum preferably 60 7096 non condensing Should condensation exist wait until the moisture has evaporated completely before connecting the oven to a power source and powering up Avoid direct exposure to sunli
69. release poisons create a humid atmosphere release dust exhibit exothermic reactions are pyrotechnical substances exceed the specified hurdle load Thermo Electron LED GmbH Heratherm 1 5 1 6 Safety Notes Standards and Directives Standards and Directives The oven complies with the following standards and guidelines EC EN 61010 1 IEC EN 61010 2 010 Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC Additionally the oven is in compliance with many other international standards regulations and directives not listed here Should you have any questions regarding compliance with national standards regulations and directives applicable for your country please contact your Thermo Fisher Scientific sales organization Heratherm Thermo Electron LED GmbH EN E Delivery of the Oven Packaging Heratherm ovens are delivered in a rugged packaging box All packaging materials can be separated and are reusable Packaging materials Packaging carton Recycled paper Foam elements Styrofoam CFC free Pallet Chemically untreated wood Packaging film Polyethylene Packaging ribbons Polypropylene Acceptance Inspection After the oven has been delivered check the delivery immediately for completeness possible damage If components are missing or damage is found on the oven or the packaging in particular damage caused by humidity and or water please notify the carrier as well as
70. response to pressing the On Off button control panel remains extinguished no heating operation call Customer Service to have the fuses replaced Work Space Components Inner Chamber All components of the work space are made of corrosion resistant galvanized steel and have an absolutely smooth and easy to clean surface Any embossings have a large radius Access port A re sealable capped access port can be closed off using the plugs delivered with the unit allows cables hoses or additional sensor leads to be routed into the work space of the oven The access port 2 of the Heratherm OGS 60 100 180 400 750 has a diameter of 42 mm NOTE Operating conditions When accessories are to be operated in the work space of the oven the ambient condition requirements must be observed see table below The energy introduced into the work space has an impact on the lower end of the temperature control range When additional heating sources are introduced into the work space temperature control may be adversely affected Thermo Scientific Heratherm 4 13 Product Description Work Space Components Shelf System The oven is supplied with two wire mesh shelves The shelf support rails have an alternating pattern of oblong and round perforations spaced evenly at 30 mm allowing the shelf support brackets to be inserted without any room for error yet in a very flexible way to accommodate differen
71. riations during the measurement put the measuring sensor in an isothermal container such as a bowl filled with glycerol before placing it in the work space Use the center of the work space as the reference location for the comparison measurement N Q TE Isothermal Container Do not use a container filled with water as an isothermal container because the evaporation of water will result in a lower temperature reading N O TE Excessive Work Space Temperatures Excessive work space temperatures subsequent to a calibration run can be reduced by leaving the door open for approx 30 seconds Comparison Measurement Procedure 1 Turn the oven on using the power switch 2 Set the temperature set value and allow the oven to stabilize This may take several hours 3 Place the measuring device in the center area of the work space Alternatively a temperature sensor may be positioned in this location Route the connecting cable between the glass panel and the interior tank 4 Close the doors 5 Wait until the temperature value displayed on the measuring instrument has stabilized 6 Use the temperature reading from the measuring device to calibrate temperature control manually as explained Entering the Calibration Reference Temperature Manually on page 7 11 Temperature Calibration Procedure For detailed instructions on how to perform a manual temperature calibration please refer to the instructions in the section
72. rm OMS Series Oven Overview The individual features of OMS Series ovens are shown in the figures below Q4 0000000 Temperature sensor Exhaust air tube Figure 4 7 Heratherm OMS Series Front View 1 Outer door 2 Door latch cutout 3 Door latch and handle 4 Door hinge lower 5 Levelling foot 6 Nameplate 7 Air baffle top piece 8 Support rail for wire mesh shelf 9 Shelf support 10 Fan cover integrated into air baffle 11 Door hook catch 12 Air baffle 13 Door seal 14 Stacking pad 15 Spring for air baffle 16 17 Thermo Scientific Heratherm 4 9 Product Description Heratherm OMS Series Oven Overview 4 10 Figure 4 8 Heratherm OMS Series Rear View Ko 1 2 3 4 5 6 7 8 9 10 11 12 Sea ee e n e e ea e ee eee Heratherm Door latch and handle Control panel Stacking pad Spacer Exhaust air tube Mechanical air inlet slider Electronics compartment Levelling foot Thermo Scientific Product Description Safety Devices Safety Devices The oven is equipped with the following safety features asample protection feature that safeguards the samples against destruction through overheating in case of contoller failure an overheat protection cut out feature that shuts down the oven completely when excessive temperatures occur in the workspace dual fuses rated at 16 amperes Work Space Atmosphere To ensure undisturbed opera
73. rm Thermo Scientific Product Description Heratherm OGS Series Oven Overview Figure 4 2 Heratherm OGS 60 OGS 100 OGS 180 Series Rear View Door latch and handle Control panel Stacking pad Spacer Mechanical air inlet slider Electronics compartment 1 2 3 4 5 6 ri 8 9 1 1 12 Levelling foot 2 3 4 5 6 7 8 9 10 11 12 Thermo Scientific Heratherm 4 3 Product Description Heratherm OGS Series Oven Overview 4 4 ee SSS eS SS e Figure 4 3 Heratherm OGS 400 Series Front View 1 2 3 4 5 6 7 8 9 1 1 1 1 1 1 1 1 1 1 2 2 2 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 a CI c C cC a E S E iaaa Heratherm Outer door Door latch Unit caster Air baffle bottom Wire mesh shelf Door hook catch Temperature sensor Exhaust air tube Air baffle side Thermo Scientific Product Description Heratherm OGS Series Oven Overview Figure 4 4 Heratherm OGS 400 Series Rear View Outer door Unit caster Exhaust air tube Anti tilt anchor Electronics compartment Inlet air tube Hinge Handle Display Nameplate on sidewall ONAN iX Q2 l2 i CQ c c Cc C CC Aa A 2 CL ccc coa2c Thermo Scientific Heratherm 4 5 Product Description Heratherm OGS Series Oven Overview Figure 4 5 1 2 3 4 5 6 7 8 9 1 1 1 1
74. rts 50127926 Stainless steel perforated shelf OGS 180 OGH 180 OGH S 180 includ ing 2 shelf supports 50128182 Main board cooling fan Heratherm Advanced Protocol and Advanced Pro tocol Security heating amp drying ovens 50128184 Sample sensor connection for Heratherm incubators and heating amp drying ovens 50128186 Kit window bulbs Heratherm heating amp drying ovens 50128237 Kit Key for door handle with lock Heratherm 50128880 Reinforced wire mesh shelf OGS 180 OGH 180 OGH 180 S 50128881 Reinforced wire mesh shelf OMS 180 OMH 180 OMH 180 S 50128887 Kit hot air flexible tube for Heratherm built in units 50130347 Fibre glass pads 20 mm 0 8 inch 50130348 Fibre glass pads 50 mm 2 inch 50130657 Kit Viton door seal 60 L Heratherm 50130658 Kit Viton door seal 100 L Heratherm 50130659 Kit Viton door seal 180 L Heratherm 50134094 Kit heating coil OGS 750 230 V 50134115 Kit heating coil OGS 400 750 230 V 50134118 Kit heating coil OMH 750 230 V 50134119 Kit heating coil OMH 750 3 Ph N 50134124 Kit heating coil OGS 750 3 Ph 50134125 Kit heating coil OGS 750 3 Ph Heratherm Thermo Scientific Spare Parts and Accessories Material No Description 50134315 Kit DS bus cable cpl 400 750 50134326 Door gasket 400 L HTM 50134327 Door gasket 750 L HTM 50134328 Kit profile gasket 750 L HTM 50134329 Kit door conn clips 400 750 HTM 50134333 Kit
75. s commands for viewin P pop 8 general status information on the unit and setting preferences for the operation of the oven or its display window Read access to error log e Calibrating the oven Toggling the temperature display unit between C and F Toggling process protection on and off Entering a configuration control code Instructions for using these features are given in the following Error Log Users calling customer service for support may be asked by the agent to supply information from the error log of the oven It enables the user to browse through the most recent 22 alarm messages that were caused by hardware or control loop errors Each error is displayed with an internal error code Error codes and instructions for clearing alarm conditions appear in the section Error Codes on page 12 1 Table 7 10 Reading the Error Log Press to activate the menu bar then use 1223 or to select the Settings icon and press to confirm The word Err appears in the display pane to indicate that the error log has been selected Use the button to select the first entry in the error log numbered E01 Error 01 This entry represents the most recently registered error After a few seconds the display pane automatically switches to the internal error code for example 109 E01 shows the latest fault E22 shows the oldest fault Thermo Scientific Heratherm 7 9 Handlin
76. sabunaPepuatass 5 1 Inialanscillationooate Sen oo pend derer Dutton utei rum de 5 1 Tust llime the SM el vingt etre pnt e dla novae ente covnd bu sasdsaensncitants tatu ces Mese odere LS us 5 2 Pr paring the Wo tk Space roisse mid uo ida tei ch cuia cat eei ep E ERR IE I eio aus QA MD EAR 5 3 BU ILI Hn T 5 3 Installation or Removal of the Support Rails OMS Series only eee 5 3 Installing and Uninstalling the Rear Air Baffle OMS Series only eee 5 4 Installing and Uninstalling the Air Baffles OGS Series only eer 5 5 Commissioning of floor stand Ovens audies ales Qus dee Ue sepa ceat P pR pesca suden ed esa ded REIS 5 7 Installing Removing air baffles OGS Series suadeat pne ictor eddie iactu xck ia well gauss 5 7 Gommissi ning general ise aas disp RE Oed Bleed io en UA ERES Dn E eM aU Diae id apad Mati iaa 5 8 Insel the Shel b Support Brackets 2uniasGrieltatie piesdtuscl tisssdd itio estat ode foam omo ie Hia steaks 5 8 Installing the Witenes Ve VES dit nad e ea tion ene aese tbc ia ius epe bite dire ud 5 9 Levelling the Table top ov6nsuna etes sn aene tor gre i tost te petu uates e fu Ao ES oput 5 9 Maius COME CTI ON ceret duce eidem demde E acque dua P o Pede 5 10 Connection to the Power Supply SQUECe d uai dete etis br gene arai ande titeo Eon deti eus 5 10 Connecting the R 8 732 InEekf368 tierie acad e dust ui Gb a optet aped ia roten dd 5 12 Interconnecting the Oven with a Comput
77. sage shown on display Check the external refer ence sensor for proper function and replace if necessary If this does not solve the problem call ser vice Sensor Signal E107 of the A D converter out put for the reference sen sor has changed over a specific time period cess sensor audible alarm activated message shown on display If both sensors are defective all control cir cuits will be disabled Constant Sensor Sig None of the decimal places Control transferred to refer Call service nal E106 of the A D converter out ence sensor audible alarm put for the process sensor activated message shown has changed over a spe on display If both sensors cific time period are defective all control cir cuits will be disabled Constant Reference None of the decimal places Control continues on pro Call service 12 2 Heratherm Thermo Scientific Table 12 1 Heratherm Oven Error Codes Error Message amp Code Heating Relay Error E109 Root Cause The voltage measurement has indicated a defect in the heater circuit relay Alarm Response Device completely inopera tive audible alarm acti vated message shown on display Error Codes Alarm Clearing Instructions Be sure to pull the power plug and disconnect the device from the AC mains Call service Heating Triac Error E110 The voltage measurement has indicated a defect in the triac Audible alarm act
78. ssings 5 Secure the air baffle to the work space back wall by fastening the two screws at 1 5 4 Heratherm Thermo Electron LED GmbH Start up Table top ovens Installing and Uninstalling the Air Baffles OGS Series only The following section describes the installation and removal of the air baffles Figure 5 6 Removing the Bottom Panel 1 Losen the two screws 1 in the bottom panel then remove the entire bottom panel by lifting it out of its two embossings Figure 5 7 Bottom Panel Removed 2 Grab the two retaining springs 1 at their tabs and pull them downwards out of the embossings then pull off the lateral air baffle A WARNING Risk of damage to sensor To prevent accidental damage be sure to avoid collision with the sensor when installing or uninstalling panels in the oven s workspace Thermo Electron LED GmbH Heratherm 5 5 Start up Table top ovens Figure 5 8 Removing the Lateral Air Baffle 3 For the lateral air baffles to install correctly the two retaining springs 1 must be facing upwards Place the lateral air baffle on the lower embossings and tilt it upwards against the side wall of the work space 4 Clamp the two retaining springs 1 into the upper embossings 5 Replace the bottom panel into the embossings and secure it by fastening the two screws at 1 5 6 Heratherm Thermo Electron LED GmbH Start up Commissioning of floor stand ovens Commi
79. ssioning of floor stand ovens Installing Removing air baffles OGS Series The section below describes how to install remove the bottom plate Figure 5 9 Removing the bottom plate 1 Loosen and remove the four 4 screws in the bottom plate and then remove the bottom plate completely Figure 5 10 Removing the left and right support profiles Loosen and remove the eight 8 screws for the left and right support profiles and then take out the lateral air baffles Thermo Electron LED GmbH Heratherm 5 7 Start up Commissioning of floor stand ovens Figure 5 11 Removing the rear air baffle OGS 400 750 On the OGS 400 750 model remove the ten 10 screws for the rear air baffle and then remove the air baffle Commissioning general Installing the Shelf Support Brackets 1 Insert the shelf support brackets 3 into the perforations 1 of the support rail and air baffle and tilt them downwards 2 Make sure that the two vertical elements 2 of the shelf support bracket butt against the support rail and air baffle NO TE Horizontal position of support rails Please note the alternating sequence of round and oblong holes Be sure to use the correct pair of opposite holes so the support rails are truly horizontal 5 8 Heratherm Thermo Electron LED GmbH Start up Commissioning of floor stand ovens 0 Sc Tik Figure 5 12 Shelf Support Bracket Installation Installing the Wire m
80. t further notice Concerning translations into foreign languages the German version of these operating instructions is binding Keep these operating instructions close to the oven so that safety instructions and important information are always accessible Should you encounter problems that are not detailed adequately in these operating instructions please contact Thermo Electron LED GmbH immediately for your own safety Thermo Electron LED GmbH Heratherm 1 1 Safety Notes Operational Safety Rules Operational Safety Rules The following rules must be heeded when working with Heratherm ovens Warranty Observe the sample weight limits specified for your Heratherm oven as a whole and its shelving in particular see Technical Data on page 13 1 Do not load the bottom of the interior workspace to avoid the risk of overheating any samples placed there Arrange the samples evenly throughout the work space making sure not to place them too closely to the interior walls to ensure a uniform temperature distribution Do not load your Heratherm oven with substances that exceed the capabilities of the available lab apparatus and Personal Protection Equipment to provide sufficient degrees of protection to users and third parties Check the door seal once a month for proper sealing performance and possible damage Do not process any samples containing hazardous chemical substances that may be released into the ambient air thro
81. t heights of sample containers The shelves have an integrated tilt protection and withdrawal stop For details on using the shelf system see the section Start up on page 5 1 Retaining spring Air baffle lateral Support rails Wire mesh shelf Air baffle bottom 1 2 3 4 5 Figure 4 12 Shelf System OGS Series Oven Table top ovens 4 14 Heratherm Thermo Scientific Product Description Tube Access Ports d i 1 I y V I L L XDC E P I 7 1 Retaining spring 2 Air baffle rear 3 Shelf support 4 Wire mesh shelf 5 Support rail for shelf Figure 4 13 Shelf System OMS Series Oven Table top ovens Tube Access Ports Heratherm heating and drying ovens may be equipped with additional tube access ports in the side and top panels Available tube access port options are listed in table 4 1 below Tabelle 4 1 Tube Access Ports for Heratherm Heating and Drying Ovens Option Side Panel Mounted Port Top Panel Mounted Port Model dia in mm inch dia in mm inch OGS 19 0 75 or 53 2 09 24 0 95 or 58 2 28 OMS 24 0 95 or 58 2 28 24 0 95 or 58 2 28 The tube access ports are mounted in fixed locations in the side and top panels see figure 4 14 Thermo Scientific Heratherm 4 15 Product Description Tube Access Ports iss Figure 4 14 Tube Access Ports 1 Top panel mounted tube access port 2 Side panel mounted tube access port 3 Seal
82. temperature Max humidity in service non condensing Min storage temperature Max storage temperature Max humidity in storage non condensing Post transport acclimation time Noise level Pollution degree to IEC EN 61010 1 Site conditions Maximum altitude above sea level Minimum side clearance Minimum front clearance Minimum back wall clearance Heratherm Unit mm in kg lbs kg lbs kg lbs Hz C F C F r F 96 r H C F C F 96 r F 96 r H h dB A m y ASL mm in mm in mm in OGS60 OGS100 OGS180 565 565 738 25 2 25 2 29 1 42 93 53 117 66 146 25 55 50 110 50 110 75 165 1730 1680 1680 14 4 14 0 14 0 1 N PE 1 N PE 1 N PE 60 60 120 120 IP 20 l II 16 2x16 18 65 32 90 80 non condensing 20 68 60 140 90 non condensing no inherent noise 2 2000 2187 50 2 590 23 2 690 27 2 814 32 80 3 2 OMS 60 OMS100 OMS 180 565 565 738 25 2 25 2 29 1 42 93 53 117 66 146 25 55 50 110 50 110 75 165 1440 1660 1660 12 0 13 8 13 8 1 N PE 1 N PE 1 N PE 60 60 120 120 IP 20 Il 16 2x16 18 65 32 90 80 non condensing 20 68 60 140 90 non condensing 45 52 52 2000 2187 50 2 690 27 2 80 3 2 590 23 2 814 32 Thermo Scientific Technical Data Table 13 1 Technical Data OGS and OMS Series 120 V Table top ovens Parameter Unit OGS 60 OGS100 OGS180 OMS 60 OMS 100 OMS 180 Minimum bottom mm in 200 8 200 8 cle
83. the remaining three digits exactly as described above Enter code 1234 to reset the user calibration By confirming your entry for the last digit with ES the new configuration is activated immediately The display returns to its default mode The Settings icon in the menu bar will go out Thermo Scientific Heratherm 7 13 Handling and Control Settings 7 14 Heratherm Thermo Scientific MENS E Shut down This chapter provides instructions for shutting the oven down for prolonged periods of time that is at least for several days in a row Shutting the Oven Down 1 Remove the containers with the samples and all accessories from the work space 2 Turn the oven off using the control panel 3 Unplug the power cord and secure it against accidental reconnection 4 Until the oven is shut down the work space must be continuously ventilated Leave the door open and secure it against accidental closure Thermo Scientific Heratherm 8 1 Shut down Shutting the Oven Down 8 2 Heratherm Thermo Scientific LLL Cleaning and Disinfection Cleaning Some oven components are made of plastics Solvents may attack plastics Strong acids or alkaline solutions may cause embrittlement of plastics NCAUTION Moisture sensitive components Do not spray cleaning agent onto the control panel and the control box at the rear of the oven When wiping the oven clean always make sure that no moisture enters in
84. thorization number RMA 10 4 Heratherm Thermo Scientific Maintenance Returns for Repair Material returned without an RMA number will be refused NWARNING Contamination hazard The oven may have been used for treating and processing infectious substances which may have caused contamination of the oven and its components Prior to return shipment it is therefore mandatory that all oven components be properly decontaminated Clean the oven components thoroughly then disinfect or decontaminate them depending on application Fill in and attach a safety declaration with details on decontamination activities performed to the items that are to be repaired Thermo Scientific Heratherm 10 5 Maintenance Returns for Repair 10 6 Heratherm Thermo Scientific es i Disposal NwARNING Contamination hazard The oven may have been used for treating and processing infectious substances which may have caused contamination of the oven and its components Prior to disposal it is therefore mandatory that all oven components be disposed of properly decontaminated Clean the oven components thoroughly then disinfect or decontaminate them depending on application Attach a declaration of decontamination with details on decontamination activities performed to the items that are to be Overview of Materials Used Component Thermal insulation components Material Glass w
85. tion the ambient temperature in the operating room must be at least 18 C 64 4 F The heating system controls the temperature in the oven s workspace of 50 C 122 F up to the maximum of 250 C 482 F Sensing and Control System The PT 100 type sensor for the control of the work space temperature and for the thermal protection 1 is mounted in the top panel of the work space compartment Figure 4 9 Sensor Mounting Location OGS Series and OMS Series Table top ovens Figure 4 10 Sensor Mounting Location OGS Series and OMS Series Floor stand ovens Thermo Scientific Heratherm 4 11 Product Description Data Communications amp Alarm Interface The work space temperature sensor provides the inputs to the oven s built in controller which continuously compares the measured values to the user specified set value and adjusts the heaters according to the result Protect the sensor from mechanical damage The unit features a thermal protection function that is factory preprogrammed and not adjustable It protects the samples in the work space from overheating Thermal protection kicks in on a brief violation of the upper limit based on the user selected temperature set value automatically reducing the work space temperature to the user specified set value and allowing the heating process to continue even in case of a controller malfunction If the thermal protection is activated the error message E111 Te
86. to these components Wipe the display window down with a slightly dampened cloth then wipe dry with a rag made of 10096 microfiber Cleaning exterior surfaces Remove dirt residues and depositions thoroughly using a solution of lukewarm water and commercial detergent Wipe the surfaces clean using a clean cloth and clear water Then wipe the surfaces dry using a clean cloth Wipe Spray Disinfection The manual wipe and spray disinfection is the following process predisinfection Cleaning as appropriate for the current application Thermo Scientific Heratherm 9 1 Cleaning and Disinfection Wipe Spray Disinfection NCAUTION Alcoholic disinfectants Disinfectants having an alcohol content of more than 1096 may form in combination with air easily combustible and explosive gas mixtures When using such disinfectants avoid open flames or exposure to excessive heat during the entire disinfection process Use such disinfectants only in adequately ventilated rooms After the disinfectant has been allowed to react wipe the cleaned oven components thoroughly dry Observe safety regulations to avoid fire and or explosion hazard caused by alcohol containing disinfectants Chloride containing disinfectants Chloride containing disinfectants can corrode stainless steel and galvanized metal surfaces Use only disinfectants that do not affect stainless steel and galvanized metal surfaces
87. ugh defective seals or may cause corrosion or other defects on parts of the Heratherm oven Thermo Electron LED GmbH warrants the operational safety and functions of the Heratherm ovens only under the condition that the oven is operated and serviced exclusively in accordance with its intended purpose and as described in these operating instructions the oven is not modified only original spare parts and accessories that have been approved by Thermo Electron LED GmbH are used third party spares without Thermo Electron LED GmbH approval void the limited warranty inspections and maintenance are performed at the specified intervals an installation verification test is performed on commissioning the oven for the first time and repeated after each inspection and repair activity The warranty is valid from the date of delivery of the oven to the customer 1 2 Heratherm Thermo Electron LED GmbH Safety Notes Explanation of Safety Information and Symbols Explanation of Safety Information and Symbols Safety Notes and Symbols Used Throughout These Operating Instructions Indicates a hazardous situation which if not avoided will result in death or serious injuries Indicates a hazardous situation which if not avoided could result in death or serious injuries Indicates a situation which if not avoided could result in damage to equipment or property NOTE Is used for useful hints and infor
88. utton presses After confirming the new temperature set value you may trace the resulting temperature change in the temperature display pane item D1 in figure 7 1 on page 7 1 You can also use the temperature set value to speed up cool down subsequent to a drying or heating process Temperatures as low as ambient 10 C can be selected this requires open damper and no additional heat in unit You can set the oven to a set temperature of 0 C 32 F though to speed up cool down This is achieved in one single step as described further below Table 7 4 Adjusting the Temperature Set Value Press to activate the menu bar then use to select the Temperature icon and press to confirm In the temperature display pane press or Mj to MENU adjust a new temperature set value then press E to confirm your settings The display returns to its default mode The actual temperature measured in the work space and shown in the temperature display area starts to change until it reaches the newly adjusted set value Table 7 5 Using the Temperature Set Value to Speed Up Cool Down At the end of the drying or heating process press to activate the menu bar then use to select the Temperature icon and press to confirm In the temperature display pane press to lower the temperature set value to 50 C 122 F then on to 0 C 32 F in one additional step When the display reads 0

Heratherm AP Mechanical Oven Manual - Cole

Contents

Download Pdf Manuals

Related Search

Related Contents