AD-960H & D-960H
Contents
1. Analog Camera User s Manual AD 960H amp D 960H Important Safeguards and Warnings 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 12V DC 24V AC in the IEC60950 1 We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation 2 Transportation security Heavy stress violent vibration or water splash are not allowed during transportation storage and installation 3 Installation Do not apply power to the camera before completing installation Please install the proper power cut off device during the installation connection Always follow the instruction guide the manufacturer recommended If this product is installed in the ceiling please make sure the installation position can sustain the min 50N 4 Qualified engineers needed All the examination and repair work should be done by the qualified service engineers We are not liable for any problems caused by unauthorized modifications or attempted repair 5 Environment This series camera should be installed in a cool dry place away from direct sunlight or strong light inflammable explosive substances and etc The working temperature ranges from 10 C to 60 C Please keep it away from the electromagnetic radi2. THE 1 dun eee 2 MENU m THE 1 MENU 2 MENU Lucida ERAN AUTO TYPE DC VIDEO puram ANCE MIDDLE HIGH MODE OFF SPEED LL HIGH nee LUMINANCE ENS MODE SHUTTER AUTO BSA ide o AUTO IRIS Lg SHUTTER MONIT OR OFF MOTION ON ABER BRIGHTNESS 0 255 DETECT AREA 1 4 1 4 SHUTTER SEL AGC LOW 000 288 Eas 1 3 ee MODE AUTO GAIN BOTTO 000 288 OFF M BRIGHTNESS LEFT 000 288 MANUAL MODE SHUTTER AGC oe et 288 SHUTTER 1 50 1 10 000 AGC 6 00 44 80 OFF m 4 4 SEL prop mS BALANCE R GAIN 0 255 indi USER2 B GAIN 0 255 PRIVACY RIGHT 000 468 R GAIN 0 255 MASK COLOR 1 8 ANTI CR MEME PAREN 1 00 EUN PUSH LOCK el SPEED 0 255 MANUAL LEVEL 018 040 d nal DELAY CNT 0 255 PUSH ATW FRAME x0 50 x2 00 DAY NIG AUTO 48 16 S j WAT OUTDOOR EMEN ZEN REN em BRIGHTNESS 0 255 COLOR CONTRAST 0 255 NR x YIC Y MODE m Z d FF I PICT ADJUST SHARPNESS 0 255 GAIN 0 255 SNe CAMERA CAMERA RESET 3 4 Main Interface Press the menu button for 2 seconds you can see the OSD menu appear in the monitor pe E PINT LENS PRIVACY MASK OFF SHUTTERAGC DAY NIGHT AUTO WHITE BALANCE NR zi BACKLIGHT CAMERA ID OFF PICT ADJUST SYNC INT ATR LANGUAGE ENGLISH MOTION DETECT CAMERA RESET NEXT BACK EXIT SAVE ALL EXIT SAVE ALL 17 3 5 Detailed Op
3. and impressive video The auto electronic shutter is suitable for various surveillance environments e Support auto electronic gain control self adaptive brightness Auto exposure function e Support IR function For IR series product only Advanced X Y Z axis structure support the 355 degrees rotation For dome camera series product only 1 3 Functions Day night mode Color and black white switch This function allows the camera to display the color video in the daytime while the black and white video at the night It is to enhance camera sensitivity and definition ICR The IR cut removal is to filter the IR light in the daytime and then auto switch to the general fitter at night This function allows the camera to output the high sensitivity and clear video Auto gain function To output the standard video signal in the different illumination environments the amplifier needs to adjust in a wide range The system can enhance the camera sensitivity in low illumination and enhance the video signal output to get the clear and high definition video SNR It is the ratio value between the signal voltage and the noise voltage The higher the SNR value the lower the adverse effect It is to guarantee the clear video Auto White Balance The white balance refers to the camera to restore the white object color It allows the camera to automatically adjust the color temperature in indoor and outdoor environment just like our human
4. right button to select the item 1 The 6 pin socket of the circuit board of the X Y Z rotation module A 6 pin 1 25 space winding displacement 200mm KW fa f The 6 pin socket of z gt A Eis the key board CSI Left lol 6 Right E eil j Confirm Down Figure 3 12 24 Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Circuit Board Component Device Construction Material Packing Components Accessories _ O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard Note e This manual is for reference only Slight difference may be found in the user interface e All the designs and software here are subject to change without prior written notice lf there is any uncertainty or controversy please refer to the final explanation of us e Please visit our website or contact your local service engineer for more information 29
5. then draw the cable through the cable exit you just dug in the ceiling wall Line up the four screw holes in the device pedestal to the four plastic expansion bolt holes in the installation position Put the four self tapping screws in the four plastic expansion bolts firmly 13 Step 5 Adjust the device position and then line up the three inner hexagon screws of the device to the three holes in the installation ceiling wall Put the three inner hexagon screws to the screw holes of the device pedestal and then use the inner hexagonal wrench to secure firmly C1 Ceiling or Wall p Expansion Bolt C3 Self tapping Screw C 4 Inner Hexagon Screw t CH Inner Hexagonal Wrench Figure 3 8 Step 6 Push the two sides of the inside enclosure of the dome to remove the tab D2 Loose the fixed screws D4 and then turn the X Y Z rotation module D3 to adjust the camera lens to the proper monitor angle See Figure 3 9 4 Fixed Screw 3 X Y Z Rotation Module Tab Dome Inside Enclosure Figure 3 9 14 Step 7 Put the done inside enclosure back and then put the dome cover back Line up the three inner hexagon screws to the holes of the device Use the inner hexagonal wrench to secure the screws to complete the installation See Figure 3 10 A Inner Hexagon Screw F 3 Dome Cover 7 Dome Inside Enclosure Inner Hexagonal Wrench Figure 3 10 3 2 Fixed Camera Here we take the 50M IR wat
6. to modify the following three digit code Select the character and then click the CLR click the confirm button to remove the specified character Please change the initial mark code 1 as 0 Now you have completed the camera ID mark code Use the direction buttons to select POS J and then click the confirm button you can go to the position setup interface Please click the direction buttons to set the camera ID overlay position on the screen Click the confirm button to exit 3 5 12 SYNC MODE The system supports INT setup 3 5 13 LANGUAGE The parameter includes English Japanese and etc The default setup is English 3 5 14 CAMERA RESET Please select the reset item and then click the confirm button to restore the factory default setup 23 3 5 15 OTHERS Next Click it to go to the sub menu Back click it to return to the previous menu Return click it to exit the menu setup interface SAVE ALL Click it to save current setup Important After you completed the setup please click the SAVE ALL button to save current setup and then exit the menu It is to guarantee the camera setup after the power failure 3 6 Menu Keys Operation Please refer to the following figure to operate the keys to set the OSD menu See Figure 3 12 Here you can see the camera menu keys Press the key in the middle for 2 seconds you can call the menu And then you can click the up down button to move the cursor and then use the left
7. 2 6 Figure 2 6 For the dome camera Figure 2 6 Dome camera pedestal please turn the device upside down to see the pedestal Connect to the DC 12V power to 5 Power input port input the power BNC port is to output analog video Video output port o l You can connect to the devices such as the DVR or the NVR It is to control the IR light on off T Photosensitive component status according to the environment illumination It is to send out the IR IR light compensation light to enhance the night vision Important For the dome camera there are two cable exits one is at the bottom and one is at the side Please use the rubber dustproof plug to secure the idle exit The power cable and the video output cable both pull through the cable exit Figure 2 7 2 2 3 Day Night High Resolution Dome Camera AD 960H Please refer to the following figure for detailed information See Figure 2 8 Figure 2 8 Please refer to the following sheet for detailed information Name Installation pedestal Connect to the DC 12 power to Power input port l input the power BNC port It is to output analog video signal Power output port You can connect to the devices such as the DVR or the NVR 3 Installation 3 1 Dome Camera The dome camera usually mainly uses the in ceiling installation Here we take the IR vandal proof dome camera as an example For other series dome camera please refer to the similar installation s
8. ER AGC SHUTTER 150 AGC 6 00 RETURN e Shutter The parameter includes 1 50 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10 000 Auto gain The parameter includes 6 00 12 00 18 00 24 00 30 00 36 00 42 00 and 44 80 3 5 3 WHITE BALANCE WB The parameter includes manual anti cr push lock user user2 ATW Manual MANUAL WB LEVEL UP LEVEL DOWN PRESET RETURN User1 USER1 WB B GAIN R GAIN B gain It is to adjust the blue gain Please use the left right button to set The value ranges from 0 to 255 e R gain Itis to adjust the red gain Please use the left right button to set The value ranges from 0 to 255 Note The user2 setup is the same with the user1 ATW ATW SPEED 239 DELAY CNT 003 ATW FRAME x1 00 ENVIRONMENT INDOOR RETURN ATW It is the auto trace white balance The camera can adjust the color temperature according to the actual color hue environments Speed The value ranges from 0 to 255 Please use the left right button to set e Delay control The value ranges from 0 to 255 Please use the left right button to set ATW frame The parameter includes x0 50 x1 00 x1 50 x2 00 e Environment The parameter includes indoor outdoor Please use the left right button to set 19 Push lock It is to click the OK button to lock the white balance Anti color roll ANTI CR Click it to enable the color roll control function 3 5 4 HLC BLC The backlight compens
9. ation object and environment Please keep the sound ventilation Do not allow the water and other liquid falling into the camera 6 Accessories Be sure to use all the accessories recommended by manufacturer Before installation please open the package and check all the components are included Contact your local retailer ASAP if something is broken in your package 7 Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work Use the dry soft cloth to clean the device If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device Please put the dustproof cap to protect the CCD CMOS component when you do not use the camera 1 General Introduction 1 1 Overview This series analog camera adopts the high sensitivity CCD and advanced circuit design It is featuring the high quality video the lowest distortion low noise and etc This series product is suitable to be used in surveillance system and video process system 1 2 Features e High performance SONY CCD high resolution vivid and impressive video e Support auto day night mode switch to realize the monitor both in the daytime and at night e Support backlight compensation function BLC e Support auto white balance function Restore high definition and more reliable video e High signal to noise ratio SNR clear
10. ation parameter includes OFF BLC HLC e BLC This function allows you to see the vivid video in the backlight environment e HLC This function allows you to see the vivid video in the highlight environment 3 5 5 PICTURE ADJUST Click the confirm button to go to the sub menu PICT ADJUST MIRROR BRIGHTNESS CONTRAST SHARPNESS HUE GAIN RETURN Mirror It is to set the horizontal mirror The parameter includes on off Brightness The value ranges from 0 to 255 Please use the left right button to set Contrast The value ranges from 0 to 255 Please use the left right button to set Sharpness The value ranges from 0 to 255 Please use the left right button to set Hue The value ranges from 0 to 255 Please use the left right button to set Gain The value ranges from O to 255 Please use the left right button to set Note It is the color gain 3 5 6 ATR ATR EX The parameter includes on offa Select the on button and then click the confirm button to go to the sub menu ATR LUMINANCE CONTRAST RETURN Luminance The parameter includes low middle high e Contrast The parameter includes low middle low middle middle high high 20 3 5 7 MOTION DETECT The parameter includes on offad Select the on button and then click the confirm button you can go to the sub menu MOTION DETECT DETECT SENSE BLOCK DISP DETECT AREA MONITOR AREA AREA SEL TOP BOTTOM LEFT RIGHT RETURN Detect sensitiv
11. dome camera external enclosure counter clockwise and the remove Push the two sides of the dome camera internal enclosure Please refer to C6 in Figure 3 3 so that the hook drops from the X Y Z axis module Remove the dome camera internal enclosure Please refer to Figure 3 3 Step 3 Use the proper tool to open the cable exit side hole in the pedestal Please refer to B2 in Figure 3 2 and then draw the cable from the cable exit Please refer to B2 in Figure 3 2 and fix the cable in the pedestal cable channel Draw the cable port out of the cable channel side hole of the pedestal Please refer to the B2 in Figure 3 2 Step 4 Line up the four screw holes in the pedestal to the holes you just dug in the ceiling wall then input the four secure screws in the pedestal screw secure holes Fix the screws firmly to secure the dome camera in the ceiling wall Step 5 Turn the lens or the ring to adjust the camera to the proper direction Adjust the X Y Z axis to turn the camera lens to the proper monitor angle Please refer to the Figure 3 4 Step 6 Push the hooks Please refer to C4 in Figure 3 3 of two sides of the internal enclosure to the slot Please refer to C5 in Figure 3 3 of the X Y Z axis to make the internal enclosure perfectly fit the X Y Z axis After the installation please make sure the lens port of the internal enclosure is fit the camera lens Please refer to Figure 3 5 for proper adjustment if necessary Step 7 Turn dome ca
12. er proof fixed camera as an example For other series fixed camera please refer to the similar installation steps too Important Please make sure the installation surface can min support the 3X weight of the camera and the bracket Please refer to the steps listed below for installation information Step 1 Line up the two installation holes at the bottom of the device shell to the two installation holes of the pendant bracket in the front Insert the screws and then secure firmly Now you have fastened the device in the bracket Figure 3 11 Step 2 Dig four holes in the wall or ceiling and then insert the four expansion bolts into the holes Fix these bolts Step 3 Line up the four screw holes at the bottom of the pendant bracket to the four installation holes you just dug in the wall or ceiling Insert the four screws into the four holes of the bracket at the bottom Finally you can secure the bracket in the wall or ceiling 15 tep 4 Connect the device video output port to the terminal devices such as the DVR NVS and etc Then connect the power cable to the device Now you have completed the device installation and cable connection You can use the terminal devices such as the DVR NVS and etc to view the monitor video 3 3 Main Menu Please note this function is for mini dome camera high resolution dome camera and the vandal proof dome camera only Please refer to the following sheet for menu information
13. eration Use the up down button to move the cursor to the 1 MENU Use the left right button to set the corresponding parameter You can click the confirm button to go to the sub menu if current parameter checked with Select the BACK to go back to previous menu 3 5 1 LENS AUTO IRIS TYPE DC MODE AUTO SPEED 080 RETURN Auto e Mode The parameter includes DC VIDEO lt The DC is the DC auto iris and the VIDEO is video drive lens lt Please connect to the auto iris port when you select the auto iris lens e Mode It includes auto on off Speed Click the left right button to set the value The value ranges from 0 to 255 Manual It is the manual iris lens Important The different cameras support various lens type please refer to the specifications sheet for detailed information 3 5 2 SHUTTER GAIN The parameter includes auto manual AUTO AUTO SETUP HIGH LUMINANCE MODE SHUTTER AUTO IRIS BRIGHTNESS 028 LOW LUMINANCE MODE AGC BRIGHTNESS x1 00 RETURN e High luminance low luminance It is the high brightness low brightness e Mode The high luminance parameter includes shutter auto iris auto iris and shutter The low luminance parameter includes auto gain control AGC off Brightness The high luminance parameter ranges from 0 to 255 Please use the left right button to set The low luminance parameter includes x0 25 x0 50 x0 75 x1 00 18 Manual al MANUAL SETUP MODE SHUTT
14. et Color The value ranges from 1 to 8 Please use the left right button to set Transparent The parameter includes 0 00 0 50 0 75 and 1 00 Mosaic The parameter includes on off 21 3 5 9 DAY NIGHT The parameter includes autos color black and white Auto DAY NIGHT MODE BURST DEALY CNT DAY NIGHT NIGHT DAY RETURN Burst The parameter includes on off Delay control The value ranges from 000 to 255 Please use the left right button to set e Day night It is to set the minimum parameter to switch from the day mode to the night mode The value ranges from 000 to 255 Please use the left right button to set Night day It is to set the maximum parameter to switch from the night mode to the day mode The value ranges from 000 to 255 Please use the left right button to set Note In day night mode the smaller the value and the hard for the camera to switch to the black and white mode In night day mode the larger the value and the hard for the camera to switch to the color Here we recommend the default value If the system switches back and forth when you are using please set the value in night day mode larger and the value in the day night mode smaller Black and white B W BURST RETURN Burst The parameter includes on off 3 5 10 NR NOISE REDUCE DE NOISE Click the confirm button to go to the sub menu Select the on button and then click the confirm button you can go to
15. eyes does Auto exposure System can automatically set shutter speed and iris value according to the snapshot video exposure condition Auto electronic shutter The system can automatically adjust the electronic shutter when the environment light changes Waterproof This series construction shell waterproof level reaches the considerable requirement It can be installed in the outdoor environment without other protection component IR night vision for the IR series product only In the night vision condition this series product can use the IR light to allow you to see the object or realize the monitor in the low illumination environment 1 4 Specifications 1 4 1 Mini Dome and Vandal Proof Dome Please refer to the following sheet for specification Model aoe D 960H AD 960H Video Processor 1 3 SONY EXview HAD Il CCD Video Format PAL NTSC PAL PAL 976 H x582 V 976 H x582 V Effective Pixel NTSC NTSC Resolution PAL 960x576 Min Illumination Color 0 1Lux F 1 2 Color 0 05lux F 1 4 Electronic Shutter PAL Auto 1 50s 1 100 000s Manual 1 50s 1 120s 1 2505 1 500 1 10005 1 20005 1 4000s 1 10 000s NTSC Auto 1 60s 1 100 000s Manual 1 60s 1 100s 1 250s 1 500 1 1000s 1 2000s 1 4000s 1 10 000s Lens Type Default model isq14 port auto Default model is 3 6mm 2 8mm 6mm 8mm is optional aperture lens 2 8 12mm Support ICR lens Day Night Switch Synchronization Mode INT Video O
16. ity The value ranges from 000 to 127 Please use the left right button to set Block display The parameter includes on off set l Click the set button you can use the direction buttons to set the area to display the block Monitor area The parameter includes on off Area selection The value ranges from 1 4 to 4 4 Please use the left right button to set System max supports 4 areas You can use the up down left right button to set Top The value ranges from 000 to 288 Please use the left right button to set Button The value ranges from 000 to 288 Please use the left right button to set Left The value ranges from 000 to 288 Please use the left right button to set Right The value ranges from 000 to 288 Please use the left right button to set 3 5 8 PRIVACY MASK The parameter includes on offa Select the on button and then click the confirm button you can go to the sub menu PRIVACY AREA SEL MODE POSITION COLOR TRANP MOSAIC RETURN Area selection The value ranges from 1 4 to 4 4 Please use the left right button to set System max supports 4 areas You can use the up down left right button to set Top The value ranges from 000 to 288 Please use the left right button to set Bottom The value ranges from 000 to 288 Please use the left right button to set Left The value ranges from 000 to 468 Please use the left right button to set Right The value ranges from 000 to 468 Please use the left right button to s
17. mera enclosure clockwise to fasten it on the pedestal Step 8 Connect the device video output port to the terminal devices such as the DVR NVS and etc Then connect the power cable to the device Now you have completed the dome camera installation and cable connection You can use the terminal devices such as the DVR NVS and etc to view the monitor video 3 1 2 Vandal Proof and Day Night High Resolution Dome Camera Installation Please note the following figures are based on the vandal proof dome camera Step 1 Use the inner hexagonal wrench provided to loose the three inner hexagon screws in the dome cover and then open the cover See Figure 3 6 12 A1 Inner Hexagonal Wrench A Inner Hexagon Screw Figure 3 6 Step 2 Use the inner hexagonal wrench provided to loose the three inner hexagon screws in the dome and then remove the device installation pedestal See Figure 3 7 M R Inner Hexagonal Wrench K 2 Inner Hexagon Screw Figure 3 7 Step 3 Take out the installation positioning map from the accessories bag and then paste it on the ceiling or the wall to identify the installation area Draw out the cable exit and four plastic expansion bolt holes in the installation position according to the device pedestal Dig the four plastic expansion bolt holes and cable exit Insert the four plastic expansion bolts into the screw holes Step 4 Adjust the device installation pedestal to the proper position and
18. teps too Important Please make sure the installation surface can min support the 3X weight of the camera and the bracket 3 1 1 Mini and Dome Camera Installation A Dome camera pedestal installation A2 Pedestal secure screw hole A5 Pedestal secure screw Figure 3 1 B B1 Pedestal cable exit hole B2 Pedestal secure screw hole wf gt n we SH E ca um nil ie gt i gt A B3 a 1i C Dome components C1 Dome pedestal C2 Dome internal enclosure C3 Dome external enclosure C4 Dome internal enclosure hooks On both sides C5 Dome internal enclosure slot On both sides Figure 3 3 D Turn the camera to the proper posiiton Figure 3 4 E Dome camera external enclosure and pedestal installation Push the dome camera internal enclosure to make it perfectly fit the X Y Z axis rotation module slot Figure 3 5 Important When you are turning the lens X Y Z axis please make sure you have not touch the lens otherwise it may result in the low performance E1 Dome camera internal enclosure E2 Dome camera external enclosure 11 Step1 Please take the installation position map in the accessories bag and then paste it on the ceiling or the wall you want to install the dome camera Dig four holes in the installation surface and then insert four expansion bolts in the hole Secure these four bolts firmly Step 2 Turn the
19. the sub menu NR NR MODE Y LEVEL C LEVEL RETURN NR mode The parameter includes off Y C Y C e Y level The value ranges from 000 to 015 Please use the left right button to set C level The value ranges from 000 to 015 Please use the left right button to set 22 3 5 11 CAMERA ID The parameter includes on off Select the on button and then click the confirm button you can go to the sub menu Please use the direction buttons to select the character or the function and then click the confirm button to select CAMERA ID 0001 ABCDEFGHIJKLMNOPQRSTUV WXYZ0123456789 90 9 MX Q x CHR2 4 CLR POS 1 RETURN Use the up down button to move the cursor to the mark position and then click the confirm button to set the mark position Please use the left right button to select the characters and then click the confirm button to select CHR1 Library 1 CHR2 Library 2 Select the character you want to modify CLR Clear current character POS Select it to go to the camera mask position interface Mark setup After you go to the camera ID setup interface use the direction buttons 1 to select the initial character of the mark code 0 Use the direction buttons to select the CHR1 and then use the direction buttons to select character 1 Click the confirm button to change the initial character 0 as 1 You can repeat the above steps
20. utput 1Vp p Composite Output 75 Ohm BNC Above 60 dB AGC OFF White Balance Auto Gain Control Auto BLC Auto OSD Menu Control Support SHUTTER AGC Auto Manual BACKLIGHT Off BLC HLC High light compensation BLC WHITE ATW ANTI CR manual push lock push user 1 user 2 DAY NIGHT Auto external trigger black and white color PICTURE Mirror brightness contrast sharpness hue gain MOTION Detect sensitivity block display area selection PRIVACY Area selection color transparent mosaic MASK Level Y level C level Character position English Japanese and etc Working Temperature 30 C 60 C DC12V 10 A series product support Power DC12V 10 AC24V 10 DC12V 10 Power Consumption 3w MAX Dimension mm 0105x86 3 160x118 5 Weight 350g 1000g 2 Framework 2 1 Dimensions Please note all the units in the following figures are mm 2 1 1 Mini Dome Camera D 960H Please refer to the following two figures for the dimension information See Figure 2 1 46 5 86 3 Figure 2 1 Figure 2 2 Figure 2 3 2 1 2 Day Night High Resolution Dome Camera AD 960H Please refer to the following figures for detailed information See Figure 2 4 Figure 2 4 2 2 Structure 2 2 1 Mini Dome D 960H Please refer to the following figure for detailed information See Figure 2 5 Figure 2 5 2 2 2 Dome Camera Please refer to the following figure for detailed information See Figure
Download Pdf Manuals
Related Search