USER MANUAL - SIRS-E
Contents
1. LED not light the transformer has power out Check if the power input of the board is normal Check if the cable connect to the display loose Change the main board to see if it is normal Chang the display LED is connect by leds in series first then connect parallel so please check if the leds is loose Some of the LED not Use the multimeter to check if the led is bright or not of not light please change the led check whether current limiting resistor is normal or not Check constant current IC is normal or not compared with the normal IC Single color leds Check the switch of this color is normal or not always bright not Change the IC control board bright Noted only professional persons can do as above 12 Technical Specification Input voltage AC 100V 264V 50 60HZ e Consume 30W e Lamp Type LED 5 e Lamp Spec red 128PCS green 128 5 128PCS e Life span 50000 100000 hours e Control mode stand alone master and slaver e Channel 3CH 4 7 10CH 16 24CH 28CH Beam Angle 25 Anti electricity intension 1 5KV Insulation Resistance gt 2MQ Size 965 65 80mm Net Weight 2 6KG sirs e 6101 N 23rd Street Suite K McAllen TX 78504 USA e mail info sirs e com Phone 956 522 2006 Fax 956 686 7380 142. be set in DMX mode and the address code should be 001 to assure receive the master s signals correctly Only one light can be set as a Master and others are slaves Note This product uses input and output power cord 0 75 m m copper core wire power line in series when 220V AC should less than 30 lights and 110V AC less than 20 lights 9 XLR cable connecting gt cable The stand connection way of the XRL is one end connect to the male plug and the other connect to the female XRMadeSoket XLRFemalesocket 1 xLR Pin Configuration 1 Ground 2 Cold Pin 1 Ground Pin 2 Data Compliment negative 3 Hot Pin 3 Data True positive COMMON p Noted In order to avoid failures and interference signal transmission we connect a resistance1200 1 4W at the end of the DMX connecting as below Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture gt The Conversion between 3pin and 5 pin XLR If the output cable of DMX512 controller is the 5PIN please use 1pc 5PIN to 3PIN cable 3 Pin XLR 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Data Compliment signal Pin 2 ____ 10 Connecting picture Light connecting picture DMX SLAV MAS
3. current menu options DMX mode will be stored automatically and the screen will stop glinting gt CHnd DMX channel 1 Press MENU go back to the initial setting Press UP DOWN until 2 Press ENTER then shows the 3CH 28CH and glinting press UP DOWN to choose the number of receiving channel 3 Press ENTER about 2 seconds then automatically return to A001 and saved the same as glinting for 4 seconds gt SLAV slave receiving mode 1 Press MENU go back to the initial setting Press UP DOWN until SLAV 2 Press ENTER to confirm at this time will shows the SLAV and glinting then confirm again parameter save stop glinting Slave indicator lighting gt SHnd built in mode 1 Press MENU go back to the initial setting Press UP DOWN until 5 2 Press ENTER if FAFE as the gradual state if SH 1 SH 8 built in 8 kinds of programs press UP DOWN to select the program change 3 The second ENTER will show SP 1 SP 8 press UP DOWN to change speed of the current program 4 Third ENTER to return to the current program to stop glinting the parameter is automatically saved Host indicator lighting AUTO auto run mode 1 Press MENU go back to the initial setting Press UP DOWN until AUTO 2 Press ENTER at this time will show SUTO And glinting and then press ENTEN to confirm parameter save stop glinting Host indicator lighting gt Soun sound activated 1 Press MENU go ba
4. 0926 after 4CH functional control as well 4 as 7CH dd co 10 12CH 10 12CH 7 9 7 9 4 6CH 4 6CH 1 3CH 1 3CH Separated into four parts each composed by the RGB accounting for 3CH respectively the former 4CH adjust the RBG brightness 0 100 after 4CH functional control as well as 7CH m Q O OO SS 22 24CH 19 21CH 16 18CH 13 15CH 10 12CH 7 9CH 4 6CH 1 3CH Separated into eight parts each composed by the RGB accounting for respectively adjust the RBG brightness 0 100926 28 Separated into eight parts each composed by the RGB accounting for 3CH respectively the former 24CH adjust the RBG brightness 0 100 after 4CH functional control as well as 7CH 6 Display Operation DMX SLAV MASTER SOUND O O Q DMX our DMXIN FUSE Ls OUT POWER IN MENU ENTER UP DOWN gt access the menu or return to a previous menu option gt ENTER select the current menu option gt UP menu selection or parameter increments 5 DOWN menu selection or parameters decrease 7 Menu Instruction mE J 8 CE wee CE So 1 gt So 8 R0 255 1 B0 255 8 Co 8 gt DMX mode 1 Press MENU go back to the initial setting Press UP DOWN until Addr 2 Press ENTER to choose the display will glinting at this moment Press UP DOWN to choose the receiving address 3 Press ENTER to confirm store the
5. C RoHS USER MANUAL Ultra bright LED BAR RGB 384 LEDS LED BAR 384 1 safety instruction 1 Size eM P 2 main function M 3 DMX controller function m 3 Display operation instruction ee 5 TASTE CLIO esu 6 Operating control instruction ee 8 connection Instruction sick issessecsssssenssecsssessaseusvsssesssnssssovsnscndsssusdsscssviesdebonsisseeseses 9 Connection 10 Problem analysis 11 Technical Specification UTR 12 1 Summarize gt Summarize Thank you for purchasing our LED wall wash lighting Please read these instructions carefully before begin and operate the fixtures according to these instructions to avoid any possible damages and accidents causes by misusage Products introduce This led wall washer color changing projecting light is covered by tensile aluminum designed in a fashion of hydrodynamic form It takes uses high power R G B 3 kinds LED Each kind of LED can be independently dimmer color temperature from 1000K to 6000K It uses power switch performs low weight and consumption stable capability and long life The built in program includes dimmer strobe gradual change fading and s
6. TER _ SOUND O O DMX our DMXIN FUSE Ld OUT POWER IN MENU ENTER UP DOWN DMX SLAV master o Jo o O O O DMXOUT DMXIN FUSE Eu OUT POWER IN MENU ENTER UP DOWN DMX SLAV so o0 0 0 O SENSITIVITY DMXOUT DMXIN FUSE POWEROUT POWER IN MENU ENTER UP DOWN 11 Lu oooooooo wc Any DMX controller DMIX 512616 f 000000 0000 0000000 11 Problem Analysis Problem Checking way Can not tu rn on the light Check the power source plug is in normal or not Check the switch of the lights is off or on Check the fuse if in normal DMX can not control it Check the DMX cable is connect to the lights or not Check the DMX512 controller work in normal or not Check the DMX cable is normal or not Check if the lights is in DMX mode A001 Display n ot bright When connect to the electricity did the led flash one time If so the power source is normal If not please check if the switch and the transformer has power out Check if the power input of the IC board is normal Check if the cable connect to the display loose Change the main board to see if it is normal Chang the display When connect to the electricity did the led flash one time If so 12 the power source is normal If not please check if the switch and
7. ck to the initial setting Press UP DOWN until Soun 2 Press ENTER if FAFE as the gradual state if So 1 So 8 built in 8 kinds of sound control programs Host indicator lighting 3 Press to confirm the parameter is automatically saved sound indicator lighting gt CoLo color selection 1 Press MENU go back to the initial setting Press UP DOWN until CoLo 2 Press ENTER if it shows nanu Manual for the RGB dimmer state and then ENTER key separately adjust the r000 9000 5000 brightness when once again returned to nanu the parameters are stored and stop glinting If the show Co 1 Co 8 built in 8 kinds of colors press UP DOWN to select then press ENTER parameter save stop glinting gt bLnd close the light 1 Press MENU go back to the initial setting Press UP DOWN until bInd 2 Press ENTER will show ON or OFF the press UP DOWN to select 3 Press ENTER parameter save stop glinting note when choose ON is close the light 8 Operating Control Instruction Master Slave Master The master should always working as a master as long as it is not set in a DMX mode whatever other modes itis And it send out the signal so that the slave synchronous with it To avoid the host signal and DMX512 signals interfere with each other should cut off the DMX512 signals The signal lines are longer than 60 meters 20 lamps should increase a signal amplifier Slave the Slave must
8. in 8 pixels auto run sound activated master slave interconnected multi machine control using switching power supply to protect the LED to work well protection rating IP20 DMX512 channels 3 4 7 10 16 24channels 5 DMX Control Function 3CH Channel DMX Value Control Function 1CH 0 255 red diming0 100 2CH 0 255 green dimingO 10096 3CH 0 255 blue dimming 0 100 4CH Channel DMX Value Control Function 1CH 0 255 Red dimming 0 100 2CH 0 255 Green dimming 0 100 3CH 0 255 Blue dimming 0 100 4CH 0 255 General control 7CH Channel DMX Value Control Function priority 1CH 0 255 Red dimming 0 100 0 2CH 0 255 Green dimming 0 100 0 3CH 0 255 Blue dimming 0 100 0 0 26 invalid 27 53 Mode 1 54 80 Mode 2 81 107 Mode 3 108 134 Mode 4 135 161 Mode 5 4CH 3 162 188 Mode 6 189 215 Mode 7 216 242 Mode 8 243 255 Comprehensive mode 1 8 SCH 0 255 Speed adjustment 255 is the 1 fastest 0 15 invalid 6CH 1 16 255 strobe 255 is the fastest 0 15 invalid 7CH 2 16 242 Gradual change 242 is the fastest 243 255 Random sound control ems Te I EON COPS 4 6CH 4 6CH 46CH 4 6CH 1 3CH 1 3CH 1 3CH 1 3CH Separated into two parts each composed by the RGB accounting for 3CH respectively the former 6CH adjust the RBG brightness 0 10
9. o on International standard DMX 512 signal is requested Packing list e LED BAR 384 light 1PC bracket 2 pcs The use manual Warranty Card 2 Safety Information gt Safety Notes Enquire the skilled people before any repair Always make sure disconnect from the power source before setting up serving and moving Avoid direct eye exposure to the fixture when it is on A Safety instruction e Make sure the power supply voltage are consistent with this lights Ensure the use of voltage is in the range of the request technical parameter ebefore the installation please check the light s fasteners and mechanical structure have been received in good condition and appear no damage eThis light is designed for indoor use working temperature is lower than 40 degree eThe fixtures maybe mounted in any position provided there is adequate room for ventilation Make sure there are no inflammable and explosive items ornaments in 0 5 meters away eYellow green cabling earthling safety no flicker when the fixture is working on 3 Outside Size Picture 4 Main Function high quality LED low consumption high brightness stable capability and long life each color of LED with 256 dimming RGB can make over 16 7 million colors gt dim0 100 Strobe gradual change jumping change gt DMX512 Controller 3 button set DMX ID address with led display each pixel with 48 LEDS and total
Download Pdf Manuals
Related Search