LNS Plug-In configuration software -User manual
Contents
1. SCPT type SCPT_sndDelta Function Output tolerance when volume flow changes Trox Netcom LON WA5 B Plug In User manual SCPTmaxRnge nvoAl2_ Voltage SCPT type SCPT_ maxRnge Function Maximum voltage at analogue input 2 SCPTminRnge nvoAl2_ Voltage SCPT type SCPT_minRnge Function Minimum voltage at analogue input 2 Configuration of analogue output SCPTmaxFlow nvoAO_FlowSetPt SCPT type SCPT_maxFlow Function Maximum tolerance of the volume flow set point command variable upper limit of operating range SCPTmaxRnge nvoAO_FlowSeiPt SCPT type SCPT_maxRnge Function Volume flow that should be controlled at the defined maximum voltage SCPTmaxRnge nvoAO_ Voltage SCPTmaxSendTime nvoAO_FlowSetPt SCPT type SCPT_maxSendTime Function Time interval after which the volume flow set point is re sent SCPTminFlow nvoAO_FlowSetPt SCPT type SCPT_minFlow Function Minimum tolerance of the volume flow set point command variable lower limit of operating range SCPTminRnge nvoAO_FlowSetPt SCPT type SCPT_minRnge Function Volume flow that should be controlled at the defined minimum voltage SCPTminRnge nvoAO_ Voltage SCPTsndDelta nvoAO_FlowSetPt SCPT type SCPT_sndDelta Function Output tolerance when volume flow changes SCPTmaxRnge nvoAO_Voltage SCPT type SCPT_ maxRnge Function Maximum voltage of analogue output SCPTminRnge nvoAO_ Voltage SCPT type2. Microsoft and Windows are trademarks of Microsoft Corporation In the interest of readability these and other trademarks are not further marked as such in the text Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 Fax 49 0 2845 202 265 http www trox de e mail trox trox de 2 Plug in Installation The system requirements and step by step installation instructions are described below 2 1 System Requirements The Trox WA5B01 plug in is an LNS enabled plug in based on the standard of the network management tool Lonmaker 3 Before installing the plug in on your PC please check for the following system requirements e PC Recommended Pentium III 1 GHz or faster e Operating system Microsoft Windows 2000 Microsoft Windows XP e RAM At least 256 MB e Hard disk space At least 30 MB e Monitor Super VGA 1024x768 e LNS Version 3 with Service Pack 8 or higher 2 2 Installing the Plug In Check the Device Resource Files before running the installation 2 2 1 Device Resource Files DRF The definitions of the various network variable types are stored in the resource files Only standard network variables were used for the LON WAS B application so there are no manufacturer specific definitions to import The current LonMark Device Resource Files data version 12 0 or higher must be installed on the PC however 2 2 2 Installation To install the plug in l
3. e mail trox trox de 4 2 4 FlowSetPoint Tab The FlowSetPoint tab shows the set point which based on the selected operation mode and the current configurations is output to the volume flow controller through the analogue output The arrows in front of the drop down list boxes indicate which set point setting is currently valid item 1 FlowSetPoint configuration e operation mode Displays the current operation mode e variable boxflow Displays the volume flow set point of the nviBoxFlow set via the LON input The input is active only when the Variable operation mode is set e Vmin Displays the minimum tolerance of the volume flow set point command variable lower limit of operating range e V max Displays the maximum tolerance of the volume flow set point command variable upper limit of operating range X TROX LON WA5B01 ioj xj Alt Aiz AO Mode Network Traffic operation mode variable boxflow pit vs offset 0 Ws Y min gt 3 Is Ymax gt 350 Is 3 ManO veride flowvalue gt Vs flowpercent gt 0 X Trox Netcom LON WA5 B Plug In User manual e ManOveride The LON input nviManOverride includes three fields state flow percent used to set a volume flow set point The areas shown display the values set for flowvalue and flowpercent e ManOveride flow value Displays the volume flow set point set via flowvalue relative to the def
4. 0 Variable inactive active 1 Min DIB inactive active 2 Max inactive active 3 Close inactive active SCPTmaxSendTime nvoDI3_ State SCPT type SCPT_maxSendTime Function Time interval after that the DI3 status is transmitted again Trox Netcom LON WA5 B Plug In User manual SCPTdirection nvoDI4_State SCPT type SCPT_direction Function Configuration of the operating mode which is to be carried out through the digital input 4 Bit Operating mode Adjustment 0 1 0 Variable inactive active 1 Min bia inactive active 2 Max inactive active 3 Close inactive active SCPTmaxSendTime nvoDI4_ State SCPT type SCPT_maxSendTime Function Time interval after that the Dl4 status is transmitted again T ROZ Technik Automation und Systemtechnik 4 Plug in Description The interface of the WA5B01 plug in consists of six tabs Chapter 4 2 describes the contents of each tab in detail 4 1 Starting the Plug In The plug in is started through the respective device in the network management tool Lonmaker Click to select the node then right click and select Configure The plug in is restarted for each individual LON node that is the plug in enables access to the current node Delete Properties Browse Change Subsystem C
5. respective controller The applicable operating range of the command variable can then be selected within the minimum and maximum tolerances item 1 AO configuration e value min Volume flow that should be controlled at the defined minimum voltage volt min of the volume flow controller lower limit of characteristic line e value max Volume flow that should be controlled at the defined maximum voltage volt max of the volume flow controller upper limit of characteristic line e flow Setpoint Displays the actual volume flow set point based on the selected operation mode and the defined operating range Trox Netcom LON WA5 B Plug In User manual e Vmin Minimum tolerance of the volume flow set point command variable lower limit of operating range e Vmax Maximum tolerance of the volume flow set point command variable upper limit of operating range e volt min Minimum voltage of analogue output 0 or 2 VDC e volt max Maximum voltage of analogue output 10 VDC e output box flow Displays the command variable set output voltage for the connected volume flow controller 2 TROX LON WASBO1 5 xi Al alz U voltage volt max Made FlowSetPaint Network Traffic 10 0 output box flow volt min O 20 volumeflow gt VV l s value min 50 flow Setpoint value max 714 405 LON_WA5B LON_WAS5B Subsystem 1W
6. A5B 10 Chfg Online Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 Fax 49 0 2845 202 265 http www trox de e mail trox trox de 4 2 3 Mode Tab It is possible through the LON WA5 B to set various operation modes for the analogue volume flow controller The available modes are Variable mode Min mode Max mode and Close The Mode tab shows the operation mode derived from the respective volume flow controller setting The order of the input options on the tab reflects the priority of the various operation mode settings In the default setting the digital inputs have priority over the LON inputs and DI 1 has the highest priority The LON inputs as illustrated have the following relative priority nviManOverride SNVT_hvac_overid nviOccCmd SNVT_occupancy nviMode SNVT_state As soon as a valid setting is obtained via a LON input the subsequent inputs are ignored In the default state the Day mode is active The arrows in front of the drop down list boxes indicate which input is currently connected item 1 configuration mode e digital inputs DI 1 DI 4 One operation mode can be set through each of the four digital inputs Use the drop down list box to select the desired operation mode for each input amp 3 TROX LON WASBO1 ali aiz ao gt close digital inputs DI 1 gt close Alp sa DI2 By min priority DI3 gt
7. Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 Fax 49 0 2845 202 265 http www trox de e mail trox trox de 1 introduction This manual provides detailed documentation for installing and operating the LNS based plug in Trox WA5B01 for the LON coupling module LON WA5 B The applicable network variables and configuration parameters of the LON object are also described The LON WA5 B functions as a coupling module between LonWorks technology and analogue technology enabling the integration of analogue volume flow controllers into a LonWorks network The module doesn t have any project specific parameters at the delivery and must be configured on site by customer The plug in allows simple and user friendly setting of the necessary configurations for the coupling module The plug in for the LON WA5 B and the available applications xif apb file can be requested from the Internet For all the latest information please visit us on the Web at http www trox de Trox Netcom LON WA5 B Plug In User manual Copyrights Copyright 2005 Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn www trox de Issue Trox WA5B01 Updated August 2005 All rights reserved Subject to change Echelon LON LonWorks and LonMark are trademarks of Echelon Corporation registered in the USA and other countries Lonmaker and LNS are trademarks of Echelon Corporation
8. GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 Fax 49 0 2845 202 265 http www trox de e mail trox trox de Configuration of analogue input 1 SCPTmaxRnge nvoAl1_BoxFlow SCPT type SCPT_maxRnge Function Volume flow corresponding to the maximum voltage SCPTmaxRnge nvoAl1_ Voltage SCPTmaxSendTime nvoAl1_BoxFlow SCPT type SCPT_maxSendTime Function Time interval after which the actual volume flow value is re sent SCPTminRnge nvoAl1_BoxFlow SCPT type SCPT_minRnge Function Volume flow corresponding to the minimum voltage SCPTminRnge nvoAl1_ Voltage SCPTsndDelta nvoAl1_BoxFlow SCPT type SCPT_sndDelta Function Output tolerance when volume flow changes SCPTmaxRnge nvoAl1_ Voltage SCPT type SCPT_ maxRnge Function Maximum voltage at analogue input 1 SCPTminRnge nvoAl1_ Voltage SCPT type SCPT_minRnge Function Minimum voltage at analogue input 1 Configuration of analogue input 2 SCPTmaxRnge nvoAl2_BoxFlow SCPT type SCPT_maxRnge Function Volume flow corresponding to the maximum voltage SCPTmaxRnge nvoAl2_Voltage SCPTmaxSendTime nvoAl2_BoxFlow SCPT type SCPT_maxSendTime Function Time interval after which the actual volume flow value is re sent SCPTminRnge nvoAl2_BoxFlow SCPT type SCPT_minRnge Function Volume flow corresponding to the minimum voltage SCPTminRnge nvoAl2_ Voltage SCPTsndDelta nvoAl2_BoxFlow
9. SCPT_minRnge Function Minimum voltage of analogue output Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 49 0 2845 202 265 http www trox de e mail trox trox de Fax Configuration of digital inputs SCPTdirection nvoDI1_ State SCPT type Function Configuration of the operating mode which is to be carried out through the digital input 1 SCPT_direction Bit Operating mode Adjustment 0 1 0 Variable inactive active 1 Min DH inactive active 2 Max inactive active 3 Close inactive active SCPTmaxSendTime nvoDI1_ State SCPT type SCPT_maxSendTime Function Time interval after that the DI1 status is transmitted again SCPTdirection nvoDI2_State SCPT type SCPT_direction Function Configuration of the operating mode which is to be carried out through the digital input 2 Bit Operating mode Adjustment 0 1 0 Variable inactive active 1 Min DI2 inactive active 2 Max inactive active 3 Close inactive active SCPTmaxSendTime nvoDI2_ State SCPT type SCPT_maxSendTime Function Time interval after that the DI2 status is transmitted again SCPTdirection nvoDI3_ State SCPT type SCPT_direction Function Configuration of the operating mode which is to be carried out through the digital input 3 Bit Operating mode Adjustment 0 1
10. V max operation mode DI 4 gt variable z o D Vvaisble DI y y nadie ManO verride a OccCmd Occupied gt Y max bal era Unoccupied gt Y min ea cee Bypass gt Nothing hA eg Standby gt V min pA Mode Day gt v variable 7 j Reduced gt Y min sd Deas Emergency gt V max i Close gt z FlowSetPoint Network Traffic Trox Netcom LON WA5 B Plug In User manual e ManOverride Displays the operation mode set via the LON input nviManOverride SNVT_hvac_overid e OccCmd The settings Occupied Unoccupied Bypass and Standby can be defined via the LON input nviOccCmd SNVT_occupancy Use the drop down list box to assign an operation mode to each setting This operation mode will run when the corresponding setting is defined e Mode The functions Day Reduced Emergency and Close can be set via the LON input nviMode SNVT_state Use the drop down list box to assign an operation mode to each setting This operation mode will run when the corresponding setting is defined e priority Displays the current priority for the operation setting DI LON e operation mode Displays the current operation mode setting for the volume flow controller Cancel Apply LON_WA5B LON_WASB Subsystem 1 WA5B 11 Cnfg Online Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 Fax 49 0 2845 202 265 http www trox de
11. aton SNVT_flow nviMode ENVT state rene oas SNVT_volt iPade SNVT_switch AO FNS SNVT_flow I nvoAO_Voltage SNVT_volt nvoDI1_State SNVT_switch nvoDI2_State SNVT_switch nvoDI3_State SNVT_switch nvoDl4_State SNVT_switch I nvoState SNVT_state nviManOverride SNVT type SNVT_hvac_overid Function A volume flow set point or a defined operating mode of the volume flow rate controller can be set through this input The variable contains the fields state percent flow The following settings are supported Valid values status HVO_ Off no function HVO_Flow_Value Sets the set value to the flow field value based on the adjusted operating range VMin VMax HVO_Flow_Percent Sets the set value to the percent field value based on the adjusted operating range VMin VMax HVO_Close The output is set to 0 V and both relays are activated in order to force the damper blade in the full shut off position Trox Netcom LON WA5 B Plug In User manual HVO_Minimum The volume flow rate controller controls Vmin HVO_Maximum The volume flow rate controller controls Vmax Note To ensure a perfect functioning of the nviManOverride variable through the Change Format the format of SNVT_hvac_overid SI must be changed to SNVT_hvac_overid SI_LO nviOccCmd SNVT type SNVT_occupancy Function The four possible operating modes of the v
12. aunch the set up programme Setup Follow the on screen instructions The set up program automatically installs the necessary data on your PC and creates the program folder Windows Start gt Programs gt TROX LNS Plugins Accept the default installation paths Trox Netcom LON WA5 B Plug In User manual 2 2 3 Registration A one time registration of the plug in on the PC is required If registration is not run as part of the installation process it can be run later by selecting Windows Start gt Programs gt TROX LNS Plugins gt WA5B01 exe Follow the instructions to complete the registration process Registration is required for the plug in to be available in the network management tool Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 Fax 49 0 2845 202 265 http www trox de e mail trox trox de 3 Description of the function object The LON node consists of a node object and a virtual functional block The virtual functional block consists of network variable and configuration parameters All variables and parameters are based on standard network variables SNVT so that a simple integration of the LON WA5 B is ensured into the LonWorks network 3 1 Network variables LON WAS B Network Variables nviManOverride SNVT_hvac_overid nvoAl1_BoxFlow SNVT_flow nviOccCmd noe TEE SNVT_volt neni SNVT_flow Woke B
13. current input voltage at analogue input actual value of connected volume flow controller e value min Volume flow corresponding to minimum voltage voltage min Default setting should be 0 l s since the volume flow controller is factory set at O Vnominal e value max Volume flow corresponding to maximum voltage voltage max Default setting should be Vnominal of the corresponding volume flow controller since the controller is factory set at 0 Vnominal e box flow Displays actual volume flow in l s voltage gt UM i i i A i i voltage min 2 0 voltage max 10 0 input voltage 0 0 LON_WA5B LON_WAS5B Subsystem 1 WA5B Crfg Online Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 Fax 49 0 2845 202 265 http www trox de e mail trox trox de 4 2 2 AO Tab The analogue output configuration is defined on the AO tab Here it is possible to indicate the characteristic line of the volume flow controller and to define an operating range for the command variable Accordning to this it is possible when the appropriate volume flow controller setting is given to control any set point in the operating range via the LON For this reason the volume flow controller is always factory set at 0 l s Vnominai SO that the characteristic line extends across the entire volume flow range of the
14. e able to define the variable setpoint either the nviOccCmd or nviMode input in the variable operating mode must be configured SNVT_Flow nviPrioDigLon SNVT type Function Determines the priority for the operating mode change over via LON or the digital input SNVT_switch Value State Function 0 0 0 Priority DI gt 0 0 1 Priority LON In the default setting the digital inputs have priority over the LON inputs The DI 1 has thereby the highest priority The LON inputs have the following priority among themselves nviManOverride nviOccCmd nviMode As soon as a valid value is set through an input the following inputs are ignored nvoAl1_BoxFlow SNVT type SNVT_flow Function Output actual volume flow rate analogue input Al1 nvoAl1_ Voltage SNVT type Function Output analogue input voltage Al1 SNVT_volt nvoAl2_BoxFlow SNVT type SNVT_flow Function Output actual volume flow rate analogue input Al2 nvoAl2_Voltage SNVT type Function Output analogue input voltage Al2 SNVT_volt nvoAO_FlowSetPt SNVT type SNVT_flow Function Output volume flow set point analogue output nvoAO_ Voltage SNVT type Function Output analogue output voltage nvoDl1_State Trox Netcom LON WA5 B Plug In User manual SNVT_volt SNVT type SNVT_switch Function Status digital input DI1 Val
15. hange Channel i Plug Ins LON Commission o ee Decommission Replace ss Load pj Resync CPs n Cut Copy Paste a Only one plug in may be open at a time Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 Fax 49 0 2845 202 265 http www trox de e mail trox trox de 4 2 Description of the Tabs The individual tabs and their function are described in detail in the following sections 4 2 1 Al1 and Al 2 Tabs The necessary settings for the analogue inputs are made on the Al 1 and Al 2 tabs The LON WAS5 B has two analogue inputs for integrating up to two actual values of volume flow controllers into the LonWorks network The characteristic line of the analogue input actual signal of the volume flow controller derives from the minimum and maximum volume flow and the defined voltage range of the volume flow controller The following analogue input parameters can be defined item 1 Al configuration e voltage min Minimum voltage of volume flow controller 0 or 2 VDC e voltage max Maximum voltage of volume flow controller 10 VDC x TROX LON WASBO1 E Jaz aol Mode FlowSetPaint Network Traffic Y l s volumeflow A value max 405 box flow value min 50 Trox Netcom LON WA5 B Plug In User manual e input voltage Displays
16. ined operating range VMin VMax e ManOveride flowpercent Displays the volume flow set point set via flowpercent relative to the defined operating range VMin VMax e offset Offset volume flow that can be added to the volume flow set point plus sign or subtracted from it minus sign e flowsetpoint Displays current volume flow set point flowsetpoint 111 Ms Cancel Apply LON_WA5B LON_WA5B Subsystem 1 WA5B 12 Li ROZ Technik Automation und Systemtechnik 4 2 5 Network Traffic Tab The settings for data transmission to the LonWorks network can be defined on the Network Traffic tab item 1 maxSendTime configuration e nvoAl1_BoxFlow nvoDl4_state Time intervals can be configured for each existing output variable The values are re sent to the network at the set intervals This makes it possible to adapt the LON WA5 B to an existing bus load item 2 sndDelta configuration e nvoAl1_BoxFlow nvoAl2_BoxFlow nvoAO_FlowSetPt In addition to the time intervals output tolerances for a volume flow change can be defined for the three output variables If there is a volume flow change greater than the defined value the new volume flow is sent to the network lt S TROX LON WA5B01 an aiz aol Li ROZ tecunik
17. oAl2_BoxFlow SCPTmaxSendTime nvoAl2_BoxFlow SCPTminRnge nvoAl2_BoxFlow SCPTsndDelta nvoAl2_BoxFlow SCPTmaxRnge nvoAl2_Voltage SCPTminRnge nvoAl2_Voltage SCPTmaxFlow nvoAO_FlowSetPt SCPTmaxRnge nvoAO_FlowSetPt SCPTmaxSendTime nvoAO_FlowSetPt SCPTminFlow nvoAO_FlowSetPt SCPTminRnge nvoAO_FlowSetPt SCPTsndDelta nvoAO_FlowSetPt SCPTmaxRnge nvoAO_ Voltage SCPTminRnge nvoAO_Voltage SCPTdirection nvoDI1_ State SCPTmaxSendTime nvoDI1_ State SCPTdirection nvoDI2_State SCPTmaxSendTime nvoDI2_ State SCPTdirection nvoDI3_ State SCPTmaxSendTime nvoDI3_ State SCPTdirection nvoDI4_ State SCPTmaxSendTime nvoDI4_ State SCPToffsetFlow nviBoxFlow SCPT type SCPT_offsetFlow Function Through the configuration parameter it is possible to input an offset volume flow rate which can be added or subtracted from the volume flow set point This configuration allows the connection of a master slave circuit between two volume flow rate controllers with LON WAS5 B and with a constant volume flow difference Trox Netcom LON WA5 B Plug In User manual SCPTdirection nviMode SCPT type SCPT_direction Function Configuration of the operating mode which is to be carried out with the respective setting of the nvi_mode input variable Bit Operati
18. olume flow rate controller can be set through this input It can be configured freely with the aid of the appropriate SCPTdirection nviOccCmd configuration parameter at which predefined setting which operation mode is executed Default setting OC_Nul no function OC_Occupied The volume flow rate controller controls Vmax OC_Unoccupied The volume flow rate controller controls Vmin OC_Bypass no function OC_Standby The volume flow rate controller controls Vmin nviMode SNVT type SNVT_state Function Determines the function of the volume flow rate controller Bit Function 0 1 1 Day operation inactive active 2 Reduced operation inactive active 3 Emergency operation inactive active 4 Close inactive active 12 Close inactive active 13 Emergency operation inactive active 14 Reduced operation inactive active 15 Day operation inactive active It can be configured freely with the aid of the appropriate SCPTdirection nviMode configuration parameter at which predefined setting which operation mode is executed Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 Fax 49 0 2845 202 265 http www trox de e mail trox trox de nviBoxFlow SNVT type Function The volume flow rate controller can set a variable volume flow setpoint within the limits of the specified operating range through the BoxFlow In order to b
19. on mode Setting 0 1 0 Variable inactive active 1 Min Day inactive active 2 Max operation inactive active 3 Close inactive active 4 Variable inactive active 5 Min Reduced inactive active 6 Max operation inactive active 7 Close inactive active 8 Variable inactive active 9 Min Emergency inactive active 10 Max operation inactive active 11 Close inactive active 12 Variable inactive active 13 Min inactive active 14 Max Close inactive active 15 Close inactive active Note Per each setting possibility only one operating mode may be selected SCPTdirection nviOccCmd SCPT type SCPT_direction Function Configuration of the operating mode which is to be carried out with the respective setting of the nvi_OccCmd input variable Bit Operating mode Setting 0 1 0 Variable inactive active 1 Min Occupied inactive active 2 Max inactive active 3 Close inactive active 4 Variable inactive active 5 Min Un inactive active 6 Max occupied inactive active 7 Close inactive active 8 Variable inactive active 9 Min B inactive active 10 Max ypass inactive active 11 Close inactive active 12 Variable inactive active 13 Min inactive active 14 Max Standby inactive active 15 Close inactive active Note Per each setting possibility only one operating mode may be selected Gebr der Trox
20. ue State Function 0 0 0 inactive 100 0 1 active nvoDIl2_State SNVT type SNVT_switch Function Status digital input DI2 Value State Function 0 0 0 inactive 100 0 1 active nvoDI3_ State SNVT type SNVT_switch Function Status digital input DIS Value State Function 0 0 0 inactive 100 0 1 active nvoDl4_State SNVT type SNVT_switch Function Status digital input D14 Value State Function 0 0 0 inactive 100 0 1 active nvoState SNVT type SNVT_state Function Output of actual operating mode and DI DO status Bit Operating mode 0 1 0 Variable inactive active 1 Min inactive active 2 Max inactive active 3 Close inactive active 4 Flow_value nviManOverride inactive active 5 Flow_percent nviManOverride inactive active 10 Relais 2 inactive active 11 Relais 1 inactive active 12 DI4 inactive active 13 DI3 inactive active 14 DI2 inactive active 15 DI1 inactive active Gebr der Trox GmbH Heinrich Trox Platz 47504 Neukirchen Vluyn Phone 49 0 2845 202 0 Fax 49 0 2845 202 265 http www trox de e mail trox trox de 3 2 Configuration parameters LON WA5 B Configuration Properties SCPToffsetFlow nviBoxFlow SCPTdirection nviMode SCPTdirection nviOccCmd SCPTmaxRnge nvoAl1_BoxFlow SCPTmaxSendTime nvoAl1_BoxFlow SCPTminRnge nvoAl1_BoxFlow SCPTsndDelta nvoAl1_BoxFlow SCPTmaxRnge nvoAl1_ Voltage SCPTminRnge nvoAl1_ Voltage SCPTmaxRnge nv
Download Pdf Manuals
Related Search