LC-004-302 User Manual wDALI MC Switch Input Modul
Contents
1. 15 mm 5 Safety warnings 5 1 To avoid installed the product in minefield strong magnetic field and high voltage area 5 2 To ensure the wiring is correct and firm avoiding short circuit damages to components and cause fire 5 3 Please install the product in a well ventilated area to ensure appropriate temperature environment 5 4 The product must be worked with DC constant voltage power supply Please check the consistence of input power with the product if the output voltage of the power comply with that of the product 5 5 Connect the wire with the power on is forbidden Ensure proper wiring first then check to ensure no short circuit then power on 5 6 Don t repair it by yourself whenever an error occur Contact the supplier for any inquiry 6 Wiring Diagram Installation The receiver of the wDALI MC is connected to the DALI line and powered directly via the DALI signal line A typical value of the wDALI MC current consumption is 3 8mA For DALI bus supply the DALI PS can be used The connection to the DALI line is polarity free and protected against overvoltage of up to 270Vac The sender of the wDALI MC can be placed in a flush mounted socket or anywhere in the radius of the receiver The frequency range is depending on structural conditions building construction in open air the frequency reaches a distance of 300m t oe TASTER rs CoM am aster ey T4 Eing nge Button To2. A 8 T3 ini wDALI MC puts TASTER GND e Lo T2 Tastereingangsmodul Sender BUTTON len Button Input Module Transmitter LC 004 302 1 2 oe x TASTER GND E po i o 4 DALI TASTER GND I DA OUTPUT wDALI MC BUTTON Tastereingangsmodul Empf nger rs DA Button Input Module Receiver LC 004 302 2 2 Hee 5 DALI DALI puen OUT DALI f paa ee DA AKTOR 230mA DALI bal ca 16V DALI DALI PS1 Bus Stromversorgung N a o DA DALI Deckeneinwurf Bus Power Supply POWER N le Da ATOR In Ceiling Void BN L H KO L Max 64 DALI Aktoren ne Max 64 DALI Actuat ax ctuators fe 7 pr 230V maa ee pe S DALI foke AKTOR DA G4
3. COOLER and STEP WARMER are used for colour temperature control Operating modes The wDALI MC supports 3 operating modes available from firmware version V1 5 Master Mode Default In this operating mode the wDALI MC works as a control unit and sends DALI commands to the loads according to the configuration settings In combination with an other central control device this default setting should be changed to one of the other operating modes Event Message Mode If an event occurs at the input a command is sent to the target address as an event indicator this hap pens within the scope of the proprietary protocol extension This message contains information about the type of action short push long push or the end of a long push Additionally the master module can retrieve the origin of the event switch number In this operating mode the wDALI MC does not control DALI loads Slave Mode The salve mode is a passive operating mode The wDALI MC is not automatically active it only replies on request For information retrieves a set of commands can be used provided within the scope of the proprietary protocol extension or the wDALI MC can be given an address and information can be retrieved via scene retrieval The operating mode can be set within the DALI cockpit 4 Dimensions 58 5 mm wDALI Transceiver NN 33 1 mm LL 39 7 mm cE Hari 28 0 mm 14 2 mm 32 5 mm
4. LED wDALI MC Switch Input Modul Set User Manual Button modul Transmitter Receive modul Receiver Item No LC 004 302 1 Product Description The wDALI MC Switch Input Modul Set is a compact wireless Multi Control module with 4 freely pro grammable switching inpuls potential free closing contacts The module can be used in a flush box direcly behind a light switch The supply of the module directly via the DALI Line 2 Specifications supply receiver via DALI Bus typ current consumption 3 8 MA output DALI frequency 2 4Ghz frequency range upto 300m Connecting wire cross section 0 5 1 5 mm2 estimated battery lifetime 6 years Dimensions Transmitter LxWxH inmm_ 40x28x15 mm Dimensions Receiver LxWxH in mm 59x33x15mm weight 10g Transmitter 25g Receiver 3 Description 1 DALI control module with 4 general purpose inputs 2 The wDALI MC can control a DALI circuit wirelessly 3 The wDALI MC consist of two components the user interface which can be placed anywhere sen der and a transceiver which has to be connected to the DALI signal line 4 The wDALI MC can be used without any configuration effort by using the factory settings 5 Configuration via DALI line and the free software package DALI Cockpit 6 Destination address switching mode and DALI command can be assigned to each pushbutton 7 Individual addresses 0 63 group addresses 0 15
5. alter nate between sending commands X and Y lighting based If the light was previously switched off gt command X If the light was previously switched on gt command Y Briefly pressing the push button will alter nate between sending commands X and Y lighting based If the light was previously switched off gt command X If the light was previously switched on gt command Y Holding down the dimmer switch dims or brightens the lighting If the pushbutton is pressed command X is sent and the runon time starts Once the run on time elapsed command Y is sent Briefly pressing the push button and release will send command X Holding down the push button will send command Y repeated Pressing the pushbutton will send command X and then command Y repeated without long button press delay Besides the switch functions the reactions resulting behaviour has to be defined The devices that should receive DALI commands should be registered It is possible to use single de vice addresses groups or broadcast Each input can be assigned 4 addresses In the next step the DALI commands that should be send to these addresses or groups have to be defined The available set of commands is listed below command command Function number name DIRECT ARC direct arc power Level in POWER i pown ch i AND OFF switch off go to scene 0 15 Besides the recall of commands pressing a push button can also recall a DALI macro T
6. defined macros are described in the user manual of the configuration software DALI cockpit Another configurable feature is the powerup function This is a user defined reaction on a power up The following options are available for the DALI Switch Cross no action OFF go to scene 0 15 To take the startup time of DALI ballasts into account a delay time can be configured between power up and the start of transmission of the selected command This functionality of the wDALI MC can thus be interpreted as an extension for DALI control gears Although those ballasts have a POWER ON LEVEL for mains power up they don t have a predefined dim level for bus voltage return With the help of this feature the SYSTEM FAILURE LEVEL which is set at a bus voltage loss can be overruled The wDALI MC will turn to the last set light value after restarting With the described configuration settings it is possible to set complex but also very flexible light appli cations in a rather easy way DALI Instruction Set The wDALI MC operates as control device on the DALI line and transmits the predefined DALI com mands whenever the push button is being pressed It is based on the standard for DALI Control Gears IEC 62386 102 In addition to the above mentioned DALI commands there are special commands implemented for writing data transfer registers DTR and command 47 STORE DTR AS FADE RATE Furthermore the ACTIVATE command and the DT8 commands STEP
7. hese macros can be used for predefined processes for example a sequential recall of scenes cyclic Scene switch or any other sequence of user defined DALI commands DOWN dim down using fade rate The available set of macros is listed below macro required memory Go Home 2 Byte Light dims down to DAP 0 with predefined fade time then fade time is set back to a programmable value Sequential Scenes 3 Byte Selectable scenes or OFF will be sent sequentially with each button press Dynamic Scenes 33 Byte Dynamic sequence of up to 16 selectable scenes fadetimes and delays stops with next button press DALI Reset 1 Byte Sends DALI Reset address can be deleted optionally user defined cmds 5 bytes per A user defined macro file can be loaded to the switch command 19 commands max DT8 Cooler 3x 0 Byte Activates DT8 and sends STEP COOLER command 3x DT8 Warmer 3x 0 Byte Activates DT8 and sends STEP WARMER command 3x Switch On 3 Byte Switches to last recent level works only in combination with Switch Off Switch Off 2 Byte Stores last recent level and switches off Dim Up after Switch Off 2 Byte Allows to Dim Up from Off State to MAXLEVEL when having used Switch Off before For each button there are 96 byte macro memory which can be divided freely on macros for com mand X and command Y The total amount should not succeed 96bytes Detailed information on predefined macros and the setting of user
8. ion The DALI Cockpit software is a free configuration tool for DALI systems Standard DALI ballasts can be addressed and configured as well as the wDALI MC DALI Cockpit and DALI USB Interface are required for configuration only and can be removed for standard operation For simple applications the factory settings can be sufficient dim amp switch function In this case there is no need for a DALI USB interface and configuration tool With the factory settings the following commands can be retrieved the necessary commands are sent to the entire DALI circuit Broadcast factory setting Switch amp Dim T1 Macro Switch On switch on last set level T2 Dim Up T3 Makro Switch Off safe set level and turn off T4 Dim Down Info Please note that after turning off with the macro Switch OFF the macro Switch ON has to be used to for turning on This is especially important if multiple devices are in use Adjustable Functionality With the DALI Cockpit software the 4 inputs of the wDALI MC can be configured By pressing the device connected to the wDALI MC DALI commands can be sent to one or more target addresses and groups The available parameters allow very flexible and individual solutions The first settings regard the switching modalities the functionality of the switching module connected to the wDALI MC Practical examples would be A switch where brief and long pressing duration results in different DALI commands or a switching
9. key which sends commands depending on the lighting status or its deployment as automatic staircase device with configurable delay between two commands A complete list of all functions are listed in the table below rencton eeton e 1 Push Button short long 1 command X Briefly pressing or holding down the push button will send command X once 2 Push Button short 1 command X long 1 command X then 1 command Y 3 Push Button short 1 command X long 1 command X then repeatedly command Y Briefly pressing or holding down the push button will send command X one time Holding down the push button will send command X once and then command Y once Briefly pressing or holding down the push button will send command X one time Holding down the push button will send command X once and then command Y repeatedly 4 Push Button short toggle between Briefly pressing the push button will alterna Toggle command X and Y te between sending commands X and Y Push Button Toggle short toggle between command X and Y lighting status based short toggle between command X and Y lighting status based long dimming lighting status based Stairwell Function short long command X after run on time command Y Push Button short 1 command X on release long command Y repeated Push Button 1 command X then command Y repeated without long button delay Push Button Dimming Key Briefly pressing the push button will
10. or broadcast can be set as destination address 8 Various switching modes short long press toggle etc can be assigned to each pushbutton 9 The following functions are available up down off recall min max goto scene 0 15 direct arc power in as well as macros 10 DALI DT8 support for adjustable white luminaires with the help of special macros 11 The module also has an adjustable power up function In other words a user defined command can be sent on power up e g after power failure 12 Multiple wDALI MC can be used on the same DALI signal line 13 The sender module of the wDALI MC can be placed in a flush mounted socket anywhere in the radio receiver range of the transceiver module up to 300m 14 The sender module is battery powered lifetime about 6 years at typical use 15 The receiver module of wDALI MC is directly supplied with power via the DALI signal line and does not need an additional connection to the mains Addressing and Configuration Factory Settings With the help of a DALI USB interface the DALI Cockpit software tool can communicate with the wDALI MC This way the desired functionality can be configured easily on PC During the addressing process with the PC Software you will be asked to press any button of the cont rol module attached to the wDALI MC Afterwards the module will be registered and listed in the DALI Cockpit If multiple wDALI MCs are in use the order of activation will define allocat
Download Pdf Manuals
Related Search