Home
User Manual
Contents
1. safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow s
2. Press Menu to Back Smee DMX512 Poole Press Menu to Back Slave Press Menu to Back Slave Mode Sz Press Menu to Back Enter E o Press Menu to Back Enter Enter Up Dow Enter Up Down EJ Manuari Manual Operate CH XX Sasan name DA T Axx Number of Controlled Reset Enter Vere Enter All the motor reset Enter Factory All the data change to original The display will close after 30 seconds without operations 6 DMX Channels ewe eas paoe fe fencer omass cemnsineronamown rewire oos witeanmeronont SHUTTER 000 006 No function 007 065 Slow to fast strobe 066 069 No function 070 128 Pulse strobe from slow to fast 129 132 No function 133 191 Strobe fading in from slow to fast 192 195 No function 196 255 Strobe fading out from slow to fast DIMMER 000 255 Master dimming from Off to Full on 11 COLOR 000 004 No function MARCO 005 008 Static Color Red 009 012 Static color Amber 013 016 Static color color yellow 017 020 Static Color Green 021 024 Static Color Cyan 025 028 Static Color Blue 029 033 Static Color Magenta 033 036 7200K 037 040 3200K
3. any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 7 DMX 512 control connections Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 1 Ground 2 Signal 3 Signal ites Cl y i DMX controse Sta 120 Ohms DMX512 Address 26 Address13 Address 1 DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise P T SPEED ZOOM CONTROL 041 044 050 094 095 099 100 149 150 154 155 166 167 178 179 190 191 202 203 214 215 226 227 238 239 250 251 255 000 127 128 240 241 245 246 250 251 255 5600K Eight color step a
4. 10 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly g S e r MI a Nn U a connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed a CAUTION o gt Disconnect from mains before starting In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust 2 Clean the fan each week 3 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating 360W L E D M m 7 We recommend a frequent cleaning of the device Please use a moist lint free cloth OVI n g oom Never use alcohol or solvents 36pcs10W 4 in 1 RGBW LEDs There are no serviceable parts inside the devic
5. e Please refer to the instructions under Installation instructions KEEP THIS MANUAL FOR FUTURE NEEDS Should you need any spare parts please order genuine parts from your local dealer 1 Dispacking Thank you for choosing our moving head For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs Color Imagination s moving wash is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos adopts powerful LED lamps which features high brightness and stability Please carefully dispack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box 9 Wave Beam Red color Beam opening m Beam opening m Beam opening m Distance m DMX terminator is simply an XLR plug with a 120 resistor connected between pins 2 and 3 which is then plugged
6. into the output XLR socket of the last fixture in the chain Please see illustrations below 1200 4 gt PINS _ _ PIN 2 8 Technical Specifications 36PCS 10W Edison RGBW Quad high power LEDs 50 000 hours lifespan and low power consumption 8 bit smooth and 16 Bit precise resolution for PAN TILT movement 540 630 pan and 265 tilt movement Scan position memory auto reposition after unexpected movement RGBW color mixing system LED shutter LED dimming LED rainbow effect Macros effect Strobe effect with 18 flashes per second and pulse effect General dimming and blackout for all four colors 14 DMX channels DIM4 technology 4096 step linearity dimmer DMX512 master slave and sound activated controllable or auto operation Blue background LCD display Input Voltage AC110 240V 50 60Hz LED Quantities 36pcs 10W 4 in 1 RGBW LEDs Control Signal DMX512 master slave and sound activated or auto operation Control Channel 14 DMX Channels Power Consumption 360W 380W max Dimensions 350x260x350mm Packing Dimensions 395x320x460mm Net Weight 9kgs Gross Weight 11kgs 2 Safety Instructions CAUTION AN Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the
7. o there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazer 3 Operation Instructions The moving head is an LED wash light for onsite decoration purpose Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using Keep the original packages if
8. t 9 speeds No function Eight color fade at 5 speeds No function Red Green from dark to bright Green Red from bright to dark Green Blue from dark to bright Blue Green from bright to dark Blue Red from dark to bright Red Blue from bright to dark RGB from dark to bright Blue Red from dark to bright at the same time green from bright to dark Output 100 at the same time 000 255 to be from narrow beam to wide beam 000 255 Pan Tilt Motor Speed from fastest to slowest No function auto programs put a no function value between the front and end of the reset value to reset once channel is held at this value for 3 seconds put a no function value between the front and end of the reset value 4 Installation via clamp Please refer to the picture below Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise Install the second Omega holder Pull the safety rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carbine and tighten the safety screw 5 LCD Display Operations Enter DXM addre nter Up Down RATE 001 512 Press Menu to Back Address Code Pan Invert ETES 4 OR NO pu Press Menu to Back Py sine 7 Enter gt Press Menu to Back Tilt Invert cco YES O NO poe
Download Pdf Manuals
Related Search
Related Contents
GFX180 INSTRUCTION MANUAL Philips Digital Photo Album SPH8428 ViewSonic VS11964 User's Manual INSTRUCTIONS: MODE D`EMPLOI : Phihong Midspan User Manual Rev. 3.2 - Digi-Key Manual del usuario Servicio de Sello Electrónico y Copia Electrónica Trait d`union N° 56 Maroo Woodland Blue Surface 3 Copyright © All rights reserved.
Failed to retrieve file