VA5000 Alarm panel INSTALLATION & USER manual
Contents
1. iv Note Enter the access code 4 numbers Display will show GO Push the activation deactivation zone button Display will show Zone Push the appropriate zone number on the control panel i e 1 2 3or 4 Display will not change zone wili turn ON or OFF Push O K button push Cancel button The remote arm disarm function is only used in conjunction with the optional radio remote control This radio remote control requires the VA6000 radio wireless master control unit The automatic mode can be selected by pressing the Auto Manual button under the lift up flap D PROGRAMMING OF CONTROL UNITS 1 PRE PROGRAMMED SETTING The VA5000 control unit has been designed such that as soon as the battery is connected and the power turned on the unit will automatically program itself as follows N B Battery is to be connected before power turned on i Access Code 1 2 3and4 ii Clock Time 00 00 iii Horn Duration 10 Minutes ivy Zoning All detectors connected to Zone 1 and Zone 1 activated v Delay Exit delay 20 seconds Entry delay 20 seconds All detectors included in the exit entry delay path vi Automatic Mode Setto Manual All of the above functions can be altered to suit your specific needs by following the procedure detailed below PROGRAMMING INSTRUCTIONS The 5000 Control Panel has been programmed such2. i e No delay Pre Programming The system has initially been programmed to provide you with a 20 second entry delay and a 20 second exit delay and in addition all stations detectors have been programmed to be covered by these entry exit delays Programming The procedure for changing the entry exit delay times and or the entry exit delay path is as follows Enter access code Display will show GO Press exit entry button under lift up flap Display will show IN Enter required entry delay time e g 30 seconds Display will show 0030 Press O K button to lock in entry delay Display will show OUT Enter required exit delay time e g 30 seconds Display will show 0030 Press O K button to lock in exit delay Display will show EE 7 The EE is the symbol for the entry exit delay path i e The detectors that you wish to be covered by the above delays 8 Enter stations groups of detectors that you require to be on the entry exit delay path e g Enter number 1 for station number 1 Display will show EE 1 Push O K button Display will show 9 Enter any additional stations i e 2 3 or 4 that you wish to be included in the entry exit delay path 10 After entering the required stations groups of detec tors in the entry exit delay path press cancel button to restore time of day me X qu vi d Clearing Detec
3. the system will display the time of the last alarm together with the circuit that caused the alarm The alarm memory can be cleared by 1 Entering the access code Display will show GO 2 Push alarm activation button under control flap Display will show details of alarm 3 Push clear button followed by O K button 4 Push cancel button to restore time of day The symbols for each of the various circuits are as follows AL 1 Station 1 AL 2 Station2 AL 3 Station 3 AL 4 Station 4 ALP Panic Button ALH Horn cables have been tampered with ALA More than 3 incorrect attempts have been made to enter the access code on the Master Control Panel ALL Keypad Tamper ALt Battery Cover Tamper Horn Cover Tamper REMOTE KEYPAD The VA5000 system includes a remote keypad which can be used to arm and disarm the system The remote keypad is normally located inside the home but adjacent to the front or back door The remote keypad also incorporates a panic button facility and can also be located in a bedroom and used to arm and disarm the system as well as act as a panic facility To activate the panic button from the keyboard push two blue buttons simultaneously The remote keypad is operated by a four 4 digit code which can be selected and changed as follows REFER KEY PAD WIRING DIAGRAM FOR CODING 11 TELEPHONE DIALLER Optional A
4. Zn Example press 2 on the keypad Display will show Zn 2 indicating Zone 2 Enter the stations detectors that you wish to place in Zone 2 e g if you wish to include station 1 in Zone 2 push button 1 Display will show Zn 2 1 Push O K button Display will show Zn 2 Push button 2 to enter station 2 into Zone 2 Display will show Zn 22 Push O K button Display will show Zn 2 Repeat procedure to enter the various stations groups of detectors that you require to be entered into Zones Push cancel button time of day will be displayed You can check your programmed Zoning by pushing the station set button underneath the control flap followed by number 1 for Zone 1 number 2 for Zone 2 number 3 for Zone 3 number 4 for Zone 4 The stations programmed into the various zones will be displayed v ENTRY EXIT TIME DELAY a b c General The system allows you to determine the length of time that you require in order to leave the home after arming the system and enter the home prior to disarming the system i e An exit delay of 45 seconds will allow 45 seconds in which to leave the home without causing an alarm In addition you can select which stations groups of detectors you would like to be covered by the entry exit delay entry exit delay path as distinct from those stations groups of detectors that you would prefer to be on instant
5. attached to pin 9 Attach the remaining six 6 joined wires to the remaining pins 2995
6. telephone dialler can be added to the basic VA5000 such that the system will upon activation of an alarm automatically dial up to three telephone numbers You can enter and change these telephone numbers at any time The system will make six attempts in total at dialling the three telephone numbers in sequence The telephone dialler can be used to either telephone a friend e g neighbour or family your office a pager ora security organisation A unique telephone code can be used so that a Security Agency can identify the source of a telephone alarm This code will generally be issued by the Security Agency and may comprise up to six digits Please note There are several alternative coding systems and the equipment used by some Security Agencies may not be compatible with the Valet system To program telephone numbers i Enter access code 4 numbers Display will show GO ii Press Phone No button behind flap Display will show Ph iii Press 1 the keypad for Phone No 1 iv Press the numbers on the keypad for required telephone number e g 5613722 Press button display will show GO v To enter a second telephone number press Phone No button and number 2 and then enter the required telephone number as above vi Repeat for third telephone number Note In order to enter a STD number a hyphen must be inserted after the STD Area Code e g 02 64
7. 84488 12 RADIO REMOTE CONTROL A radio wireless system is available as an alternative to the standard VA5000 system This VA6000 system allows you the following feature The system can be armed and disarmed by the use of a Hand Held Remote Control Unit that can be carried in a handbag brief case or in the car The system can be armed and disarmed from outside your home and as such you do not require any exit entry delay and all detectors can be on instant alarm In addition you do not have to enter your access code each time you wish to arm or disarm the system The Hand Held Remote Control also includes a panic button that enables you to activate an alarm by the push of a button The Radio Remote Control feature incorporates digital coding 13 1 2 GENERAL NOTES 1 Access Code No function can be changed without first entering your selected access code Keypad The keypad is used to enter information into the system Cancel Key The cancel key must always be pressed after information has been entered and to remove the system from access mode i e to make the system inoperable without entry of the access code Clear Key The clear key is used when incorrect information has been entered Key The O K key is used to lock in information that has been entered displayed When pressed the display will show GO
8. M SYSTEM CONNECTION TERMINATION OF ALL WIRING Having completed all necessary wiring as per schematic Diagram 1 the next step is to terminate those wires at the Master Unit detection devices sound alarms and options FOR CONNECTION AT MASTER UNIT PROCEED AS FOLLOWS 1 2 30 For Detectors Connect as shown on Diagram 2 For Internal Horn Connect wire as per Diagram 2 to terminals 21 and 22 and to horn as shown For the External Hom with Horn cover and Tamper Switch Firstly remove the resistor from terminals 3 and 4 by loosening screws Connect the WHITE and BLUE wires to these terminals i e 3 and 4 and the RED and BLACK wires to terminals 19 and 20 At the Horn Connect the RED and BLACK wires to the two 2 leads coming from the horn and the BLUE and WHITE wires to the two 2 terminals of the tamper switch For the Strobe Connect as shown as Diagram 2 to terminals 5 and 6 For the Key Pad Connect as shown on Diagram 4 For the Battery Firstly remove the battery cover from the Master Unit as shown on Diagram Connect the REDIead inside the Master to the RED terminal on the battery Connect the BLACK lead inside the Master to theBLACK terminal on the battery Place battery inside the Master and replace cover For Power into the Master Connect the four 4 coloured wires from the Transformer to the AC Terminals as shown on Diagram 2 Do not turn power on at this time For Connection at
9. VA5000 VALET Burglar Alarm Installation and Operation Manual A B D F G H 1 J INDEX INTRODUCTION FEATURES OF THE VA5000 CONTROL UNIT DAILY OPERATING PROCEDURE PROGRAMMING OF CONTROL UNITS ACCESS CODE CLOCK HORN DURATION ZONING ENTRY EXIT TIME DELAY AUTO MODE ALARM ACTIVATION RECALL REMOTE KEYPAD TELEPHONE DIALLER RADIO REMOTE CONTROL GENERAL NOTES TROUBLE SHOOTING WIRING INSTRUCTIONS Page No oo a N fo ao 11 12 13 14 16 17 A INTRODUCTION The Valet VA5000 is a versatile highly sophisticated Burglar Alarm System designed for ease of use and maximum efficiency These operating instructions describe the method of setting up and operating the System The System is controlled by the Master Control Unit which is used to display the current state of the system and is also used to enter and change information Information is entered on the Master Control Unit and checked on the display The various features of the VA5000 are as follows Micro Processor based control unit with memory analysis 4 Digit Code Access Remote Keypad for the Front Door Zoning ability to segregate different areas Zones so that parts of a home can have detectors switched on while other areas are switched off Variable Entry Exit Delay Variable Horn Time Options Remote Control An optional Hand Held Remote Control Unit is used to remot
10. WITCH EXTERNAL HOR HORN 1 INTERNAL HORN BLACK BLUE HORN 2 ow oom D a o TOTS SSH 4 0 9 DEFOE UCM re PO300 VALET Fensnserr eate tro OED 9 IMPORTANT Any excess wiring other than the red black white or blue wires must be trimmed back so as to avoid contact with other wiring 20 P I R DETECTOR WIRING DIAGRAM 3 ex RESISTOR Cut OFF ALL J EXCESS SHIELO WARING amp CORE SHIELDED CABLE PRIOR TO WIRING DETECTOR PUNCH HOLE THROUGH BACK OF DETECTOR SYSTEMS WITH FROM FIVE 5 TO EIGHT 8 P I R DETECTORS When wiring in the 5th detector at the Control Panel to STATION 1 terminate a the red wire onto terminal 1 b the black wire onto terminal 2 c the blue wire onto terminal 8 d the white wire onto terminal 9 REMOVE THE 4K7 RESISTOR FROM TERMINALS 8 and 9 ONLY When installing additional detectors six 6 to eight 8 repeat the wiring procedure as for detectors two 2 to four 8 eg Detector 6 in series with detector two 2 on STATION 2 terminating the red wire onto terminal 1 b the black wire onto terminal 2 c the blue wire onto TERMINAL 11 d the white wire onto terminal 12 and remove the 4K7 resistor from terminals 11 6 12 SYSTEMS WITH MORE THAN EIGHT 8 P I R DETECTORS Consult your authorised Valet dealer for special wiring ins
11. alarm has been set off The control unit has initially been programmed such that the horns will sound for 10 minutes The horn duration time can be changed as follows a Enter access code Display will show GO 5 Press Horn Duration button behind lift up flap Display will show Hd c Enter length of time by pressing the appropriate numbers on the keypad e g to enter 6 minutes and 25 seconds push the numbers 625 d X Press O K button to lock in horn duration time Display will show GO e Press cancel button time of day will be displayed Note You can check your programmed horn duration time by pushing the horn duration button underneath the control flap iv ZONING a b General The detectors can connected to any one of the 4 alternative connection points at the rear of the control panel These four alternative connection points are called stations and are numbered 1 2 3 and 4 The detector or detectors connected to each one of these stations can be programmed into one or all of the 4 alternative zones displayed on the front of the control panel We would suggest that al detectors should be included in Zone 1 and that this Zone is then used when you require the whole house to be armed The remaining zones can be used in circumstances in which you wish to have part of the home armed while other parts of the home are disarmed e g At night you may wis
12. as well as the time you require to enter the home and disarm the system In addition you can determine which detectors you wish to be controlled by these delays as distinct from the detectors that you wish to be left programmed on instant Automatic Mode While the system is normally armed and disarmed by entering a code at either the Master Panel or the Push Button Keypad the system can be programmed to automatically turn itself ON and OFF at pre set times each day Telephone Dialler The optional Telephone Dialler can be programmed to ring up to three 3 telephone numbers after activation of an alarm The system will make six 6 attempts in total at ringing in sequence three 3 telephone numbers These functions are selected by using the Push Buttons beneath the control flap DAILY OPERATING PROCEDURES There are only two controls which are normally used on a day to day basis Arm Disarm The system can be armed or disarmed from either the remote keypad or alternatively the VA5000 system control panel i D i ii Remote Keypad Enter the selected code 4 numbers To arm or disarm simply enter the four 4 digit code and the system will change from arm to disarm or vice versa Control Panel Enter the four 4 digit code and push the arm disarm blue button Zone Activation Deactivation If you wish to change the zones that are activated deactivated i ii iii
13. be set to the code 1234 In order to change your code Enterthecurrent code 1234 Display will show GO b Push change code button behind control flap A Display will show C C c Enter your own access code by choosing 4 numbers and then press the appropriate numbers on the keypad Code will be shown on the display d Press O K button to lock in your selected code Display will show GO e You can now either press the cancel button and take yourself out of access mode or alternatively proceed to enter additional information i e Time etc Note If you press the cancel button you will need to re enter your access code prigi to entering any further information Note If you wish to change your code at any time simply enter your current code and follow the above procedure CLOCK The control unit will initially display the time 00 00 The procedure to set the time is as follows a Enter access code Display will show GO D Liftflapand press Time of Day button Display will show t c Enter time by pressing appropriate numbers on keypad e g if the time is 2 30 p m press keys 1430 or if the time is 7 30 a m press keys 730 d Press button Display will show GO e Press cancel button time of day will be displayed HORN DURATION The Horn Duration time is the length of time that you wish the horns to sound after an
14. ely switch the VA5000 ON or OFF This unit has the added feature of a PANIC button which will set off an alarm immediately Telephone D aller An optional telephone dialler that will automatically dial three separate user selected telephone numbers in the event of an alarm B FEATURES OF THE VA5000 CONTROL UNIT The VA5000 Control Panel is designed such that you can select and program into the System the following information 1 Your own Access Code You can choose and enter your own four 4 digit access code The code can be changed at any time after first entering the initial access code Clock The System incorporates a clock which displays the time of day and is used to i Record the time of an alarm ii Automatically turns the system ON or OFF if used in the auto mode Horn Duration You can select the length of time that the horns will sound after the triggering of an alarm Please note horn duration time is subject to local E P A and local By Laws Zoning The system allows for the use of up to four 4 separate zones such that you can select which zones or areas of the house you wish to be activated when you arm the system Each detector can be programmed into one or several zones 10 provide total flexibility with respect to the areas you wish to be covered Entry Exit Time Delay The system allows you to select the length of time that you require in orderto leave the home after arming the system
15. enabling you to enter further functions or push cancel to revert back to the time of day Hyphen Key The is used when entering STD telephone numbers Error the display shows the word error this means that an incorrect entry has been made simply press the cancel key and the display will revert to GO You can either continue with programming or press cancel button to revert to time of day Forgotten Access Code If you forget your access code a Disconnect telephone plug if telephone dialler is installed b Turn off power at the power point and remove the 240V 3 pin plug c Open battery cover and disconnect battery note horns will sound after battery cover has been opened and before battery has been disconnected d Wait 30 seconds then re connect battery e Re connect telephone if f Turn power back g Display will show 00 00 h Re enter all information into the memory as per the operating instructions remembering that access code 1234 wil be automatically in the memory 14 Changing the Battery The internal battery used to power the system during a power failure slowly loses capacity and should be replaced every two or three years To replace the battery the battery cover must be removed and this will set off the alarm To reduce the inconvenience caused by the alarm e g to stop the horn sounding firstly disconnect the power supply
16. h to have the bedroom area disarmed while the living areas are armed You can select which detector or groups of detectors are included in the various zones Pre Programming The control panel has initially been programmed such that all stations groups of detectors are set into Zone 1 and Zone 1 is activated Programming In view of the fact that the system has automatically been programmed as above it will be necessary to remove from Zone 1 any stations that are not connected to detectors Unless these stations are removed from Zone 1 alarm condition will result To remove from Zone 1 the stations that are not connected to a detector proceed as follows 1 Enter Access Code Display will show GO 2 Press Station Set key behind control flap Display will show Zn 3 Press 1 on the keypad display will show Zn1 indicating Zone 1 4 The display will then show the stations detectors that are included in Zone 1 i e Zn 11 Zn 12 Zn 13 Zn1 4 5 To remove the stations not connected to a detector push the clear button followed by the O K button at the time that the relevant station number is being displayed In order to alteror change the programming of detectors into the various zones proceed as follows a b c d e f g h i Enter access code Display will show GO Press Station Set key behind control flap Display will show
17. s Time ON OFF button behind lift up flap Display will show Tn Using the keypad enter the time you wish the system to turn on arm itself e g if the system is to be armed at 9 30 a m the numbers 930 should be pressed Display will show Tn 930 Press O K button Display will show for time off Enter the time that you require the system to turn off disarm automatically e g if you wish the system to be disarmed at 4 30 p m enter the numbers 1630 Display will show Tf 1630 Press O K button Display will show GO Push cancel button time of day will be displayed The turn on arm and turn off disarm times have now been set The automatic mode can be selected by entering your access code and pressing the Auto Manual button under the lift up flap ALARM ACTIVATION RECALL The system will record the time of day that an alarm was activated together with the station number that initiated the alarm Following an alarm the display will indicate the station detector or circuit e g panic circuit that has caused the alarm This will be displayed on the fluorescent display until the system has been disarmed Once disarmed the display will again indicate the normal time of day but the time of the alarm together with the cause of the alarm can be recalled by simply pushing the alarm activation button behind the control flap On the pushing of this button
18. stallation procedure ii Detector is operating correctly see Installation procedure iv Allstations are in correct zones AL L Alarm Check keypad tamper switch Alarm will not Operate Check the following 1 2 3 4 5 6 7 8 Horn duration is not set to zero All stations are in correct zones All radio linked detectors are set up to correct station number Detectors are operating correctly If telephone dialler option is fitted check that telephone numbers are correct and that telephone plug is installed Master control unit is set to armed Zones are activated Flashing Zone lights probable error in zone station programming e g could be caused by programming into a zone station that is not connected to a detector 16 WIRING SCHEMATIC FOR MODEL VA 5000 BURGLAR ALARM SYSTEM Diagram 1 VA 5000 SECURITY CONTROL BOK Transtormer 3 Pin Plug Were 240 volt EDD 2 External Siren In Siren Cover and Tamper Switch Passive Infra red Dus D Strobe Light j jo Passive Infra red eo Detector Coded Key Pad Option s Reed switches remote panic switches smoke and breaking glass detectors Optional Telephone Dialler to Telecom 611 Mode 3 socket see page 12 for details 1L 4 4 core shielded security cable 3 par telephone cable 2 metres of cable and socket are provided with the master station 17 VA5000 BURGLAR ALAR
19. that the initial code is 4234 Prior to entering or changing any of the program functions it is necessary to first enter the selected four 4 digit code After entering the access code the control panel will display the word GO which is an indication that you can proceed to change or enter any of the functions or alternatively arm or disarm the system The procedure for entering any of the program functions is to push the relevant button behind the control flap enter the information by use of the keypad and then push the O K button to lock the information into memory The clear button is used for removing information from the display or memory The cancel button takes you out of the access mode which means that no further information can be entered or changed without once again entering your 4 digit code After pushing the cancel button the time will once again be displayed Note It is important that the re chargeable battery is fully charged In this regard the system should not be armed until 90 minutes after the unit has been powered up i e Connected to the power supply If you have trouble in the programming of any function itis suggested that you push the cancel button and start again Simply re enter your access code and recommence the entering of information as per these instructions 1 ii iii ACCESS CODE After turning on the power unit for the first time the unit will
20. the P I R Detectors Connect the Security cable as shown on Diagram 3 Insert pin plug from Transformer into power point OPTIONS Reed Switches Remote Panic Buttons Smoke and Breaking Glass Detectors Consult your authorised Valet Distributor for the necessary connection diagrams ANY DETECTORS OTHER THAN THOSE SUPPLIED BY VALET REQUIRE Pong AION BEFORE BEING COMPATIBLE WITH THE VAS000 CONTROL 18 PRIOR TO CONNECTING ANY WIRING TO THE CONTROL PANEL DETECTORS KEYPADS HORNS STROBE LIGHT ETC ENSURE THAT THE POWER IS TURNED OFF AND THE BATTERY DISCONNECTED FAILURE TO DO SO WILL CAUSE DAMAGE TO YOUR SYSTEM AND VOID THE WARRANT Y BEFORE TURNING THE SYSTEM ON 1 CONNECT THE BATTERY FIRST REPLACE THE BATTERY COVER AND 2 TURN THE POWER ON AT THE POWER POINT IT IS ESSENTIAL THAT THIS SEQUENCE BE FOLLOWED WHENEVER ALL POWER IS REMOVED FROM THE SYSTEM FOR WHATEVER REASON VALET VA5000 BURGLAR ALARM WIRING DIAGRAM DIAGRAM 2 TO CONTROL UNIT CONNECTOR ewes eS SES eee ee Serer wee eek Fa kaa h See a Se ae ee FS 4 12 Battery Z Nc lt WHITE PANIC M BLU RE PIR DETECTOR gt BLACK ababaka RED i STROBE EN RED i BLACK WHIT n WHIT i STATION 1 STROBE n uk7 LIGHT M RESISTOR STATION 2 3LUE WHITE STATION 3 seossentra 2 mA yu S WHITE nae 4 Fst cress TE HORN COVER WITH STATION 4 TAMPER S
21. tors from Entry Exit Delay Path If you wish to remove some of the stations groups of detectors from the entry exit delay path proceed as follows Enter access code Display will show GO Press entry exit button under lift up flap Display will show the time Push O K button Display will show OUT Push O K button Display will show the various stations groups of detectors in the delay path To remove stations simply push the clear button followed by the O K button while the station is displayed 6 Push O K button to restore the time of day Note You can check your programmed entry exit delay path by pushing entry exit delay button underneath the control flap nN AO Push O K button Display will show IN Push O K button Display will show OUT Push O K button Display will show EE 1 e g Station 1 Display will show in turn the entry delay exit delay and the stations included in the entry exit delay path AUTOMATIC MODE The Automatic Mode enables you to program the system such that it automatically arms and disarms itself at pre set times e g if all the family are away from the home fora set period each day the automatic mode can be used to automatically arm and disarm the system at pre set times on a daily basis a b c d e f 9 Enter access code Display will show GO Pres
22. transformer and then the telephone plug if attached should be removed and the horn duration set to zero To change the internal battery the following procedure should be adopted a b c d e f g h i j Enter Access Code Set horn duration time to Zero by pressing Horn Duration button and Zero time Press O K If a telephone dialler is fitted remove telephone plug from socket Turn off power Disconnect the power supply Open battery cover and replace battery making sure that the RED wire is connected to battery ve terminal Close battery cover Re connect telephone dialler plug Re connect power supply Refer to programming functions for re programming J TROUBLE SHOOTING During normal operation and in setting up the system a few problems can arise which may cause you to think the system is faulty Below is listed a number of common problems which may occur and which can be easily fixed False Alarms False alarms can be caused in a number of ways and can be broken up into groups First check the display to see what type of alarm it is 1 2 3 4 AL H Alarm Check the following Horn wires shorted cut or broken AL t Alarm Check battery cover tamper switch and horn cover tamper switch AL 1 to AL 4 Alarm Wired Detectors Check the following i Wires to detectors are shorted cut or broken ii Detector has terminating resistor see In
23. tructions SYSTEMS WHERE NO KEY PAD IS TO BE INSTALLED A link must be inserted between terminals 24 and 26 which can be found in the kit spia KEY PAD WIRING DIAGRAM DIAGRAM scil mi nr d Anoa on m m m eum Sem Uu Une A STATION 4 rrr woe wl HORN 1 N ta MN lini 1 t Should your system have a link between terminals 24 and 26 it should be i removed if key pad is to be installed with the system HORN 2 gt ww me n ti GR wu 49 USO P o wow P X wet P EREE ER RED 714 BLACK 4 2 3 TA ja Pa ARATE BA ea seat Ko UO D Ap 0 p 99 an UP oU DP m ae poro me om BLUE WHITE CODED WIRES KEY PAD Ca NUN as JOINED SIX WIRES CODING THE KEY PAD Remove the ten 10 wires from the key pad pins Select the code you require but remember you cannot use the same number twice i e 1241 or 5857 will not work NOTE It is not essential to have the same code number on the key pad as on the control panel since the control panel code can have all four 4 numbers the same i e 7777 if required Attach the colour coded wire A on the key pad to the pin that relates to the first number of the chosen access code i e if access code selected is 4579 then coded wire A is attached to pin 4 The colour coded wire B is attached to pin 5 The colour coded wire C is attached to pin 7 The colour coded wire D is
Download Pdf Manuals
Related Search