to Great GPS Tracker User Manual
Contents
1. If you want to cut off restore the engine by SMS command you will firstly have to set a center main number Only the center number can send the cut off restore the engine command to the device You can set your own mobile number as the center number The command format for setting the center number is CENTER A mobile number For example CENTER A 07900000001 If set successfully you will receive an OK message in reply Note Only an SOS phone number can send the command to successfully set itself as a center number Only one center number can be set 6 6 Delete the center number Command the device via SMS to delete the center number The command format is CENTER D If set successfully you will receive an OK reply via SMS NOTE Only an SOS number can be used to delete center number successfully 6 7 GPRS time interval The default GPRS time sending interval is 10s which means the device will upload positioning data to the platform server every 10s Users can modify the GPRS sending time interval via SMS by sending TIMER time seconds f The time ranges from 10 1800 seconds For example TIMER 10 This would mean the device will upload data to the server every 10seconds NOTE To turn off GPRS function just SMS TIMER 0 6 8 Sensor alarm time setting When the vehicle power is off and ACC is at a low level if the ACC is off for over 10 minutes the device will enter sensor alarm state In t2. an auto electrician for installation Under rear windshield NOTE 4 2 1 To prevent theft of the device it should be installed as covertly as possible 4 2 2 Avoid placing the device close to higher power electrical devices such as parking sensors an anti theft device or other vehicle communication equipment 4 2 3 The device should be fixed into position with cable ties or wide double side tape 4 2 4 The device has a built in GSM antenna and GPS antenna During installation please make sure the receiving side is face up with no metal object above the device to interfere with GPS reception The following places are suggested for installation shelter in the decorated board below the front windscreen shelter around the front instrument panel non metallic material face in the decorated board below back windscreen Notice if the windscreen is coated with metal thermal protective coating or heating coating It may affect the signal In this case please change the place of installation 4 3 Device outlet specification Specification Instruction MIC MIC Connectto relay control line 6 ACC white Connect to ACC ignition Black thick Vehicle 12V 24V negative 8 V storage battery Red thick Vehicle 12V 24V positive storage battery Notes for relay wiring The relay wiring of pump oil connectors of both ends are a fine white line 85 and a fine yellow line
3. at the most In the meantime the device will upload SOS alarm data to the server and will send Main Power has been cut off Alarm Date Time 13 08 22 23 42 51 http maps google com maps q N22 571490 E113 877103 You can also send the command CALLALARM ON to open phone call alarm function and send the command CALLALARM OFF to close it Note Normally we don t suggest to open phone call alarm function The specific numbers should be preset please refer to 6 3 9 3 Low battery alarm When the device is only working with battery once the internal voltage of battery is less than 3 7V device will send a low battery alarm SMS to a specific number and alarm on the platform Low battery alarm SMS example Battery low Alarm Date Time 13 08 22 23 42 51 http maps google com maps q N22 571490 E113 877103 This means the battery is too Low and informs the user to charge it as soon as possible Note The specific numbers should be preset please refer to 6 3 9 4 Vibration alarm When the vehicle power is off and ACC status is also low and if the amount of time the ACC is low exceeds 10 minutes this time setting can be changed the device will activate a security alarm When the security alarm is on once the vehicle vibrates several times the alarm will be activated if 3 minutes later the vehicle power is still off ACC status is low the device will start the alarm At this time it will send an alar
4. located Continuously dark GPS not located 2 4 Ignition detection indication Three blue red green LEDs are flashing in a cycle 3 Interface introduction Power on off SIM card slot MIC interface H OFF Tele cutoff SOS interface Powerinterface Petrol electricity ACC interface interface L J GPS Tracker E Power working status LED GSM status LED GPS status LED 4 Method of installation 4 1 Preparation before installation 4 1 1 Open box to check whether the type of device is correct and whether the accessories are included if not please contact your distributor 4 1 2 Choose a SIM card each device needs a GSM SIM card inserted Please refer to the distributor s suggestions to choose the SIM card 4 1 3 Installing the SIM card The SIM card slot is on the right side of device Open the SIM card silicon seal then insert the SIM card into the slot do not insert the SIM card backwards When the SIM card is ready you will hear a click If not please insert again and then replace the silicon seal Note Please use a GSM network SIM card Power off before installing or removing the SIM card The SIM card used should be enabled for GPRS The SIM card used should be enabled for caller ID If the password or the pin is enabled please disable it Ensure the SIM card can send and receive SMS 4 2 Installation Device installation is covert Please refer to
5. 86 The fine white line 85 is connected to vehicle positive power 12V The fine yellow line is connected to the device relay control line Cut off the positive connection line of the pump then connect in series to the relay N C contact thick green line 87a and the other end to relay COM contact thick green line 30 Note The standard relay is 12V and only suits the 12V car battery Please choose 24V relay if itis 24V car battery 4 4 Device wiring diagram i i 2A FU FUSE p fuse box i Lat 12V or 24V D H Yello line White line Storage batter ry EA ON START Connectto ACC id SOS button orp D por dango Relay TU j a o o NO Do va Connectto microphone de Ee 5 Cautions of device wiring 5 1 Power ACC Tele cut off petrol electricity control line 4 pin 5 1 1 Standard voltage is 9V 48VDC Please use the power line which is provided by the manufacturer The red line is the positive The black line is the negative The negative should earth alone or link iron during installing Do not connect it to another ground wire 5 1 2 ACC line white is connected to the ACC switch of the vehicle Please make sure to connect the ACC line The tracker will decide whether to enter ignition detection according to ACC status If you do not connect to ACC line the device will enter ignition detection status If the vehicle vibrates when
6. GPS Vehicle tracker GPS GSM SMS GPRS User Manual Please read this manual carefully before attempting installation Pictures are for indication and illustration purposes only 1 Accessories KJ power cord standard Relay standard SOS Alarm button Microphone standard standard Please check the accessories before using Pictures are for indication and illustration purposes only 2 Features e GSM 850 900 1800 1900 Quad band e Easy voice instructing function eWide for voltage input range 9 48 vDC 90mA e GPS continuous positioning GPRS timing interval e Check location via SMS e Built in vibration sensor theft proof e ACC ignition detection e Tele cut off petrol electricity function e Three SOS numbers in maximum e SOS alarm and burglar alarm e Voice monitor function e Alarm when the power supply is disconnected intentionally with back up battery e Compatible with external connection through serial port 2 1 Red LED power working status LED Status Meaning Continuously bright Charging Continuously dark Low battery power off 2 2 Green LED GSM status indicator LED Status Meaning Quick flashing GSM initialization Continuously bright GSM conversation Start GPRS Continuously dark No GSM signal 2 3 Blue LED GPS status indicator LED Status Meaning Flashing Searching GPS signal Continuously bright GPS
7. S APN 0 APN command format Examples Text APN APN s Name IP PORT Here the IP and PORT is the SIM card s IP and PORT For 02 sim card APN payandgo 02 co uk 0 0 0 0 0 payandgo payandgof The device will reply APN has been set APN is payandgo 02 co uk 0 0 0 0 0 payandgo payandgof For T mobile sim card APN mobile o2 co uk 1 0 0 0 172 80 mobile o2 co uk is the APN of the carrier the APN varies with your mobile network provider The device will reply APN has been set APN is mobile o2 co uk 10 0 0 1 72 80 if set successfully 6 1 2 To clear APN setting please SMS APN 0 Note The APN of some countries have a user name and password you may need to send the SMS command as follows APN APN name IP PORT user name password E g APN CMWAP 10 0 0 172 80 CLIENTE AMENA 6 2 DNS setting The tracker is connected as default to the platform www gpsgreat com To connect to another platform please send the SMS command below to change the settings 6 2 1 Via DNS SERVER 0 DNS Port 0 Eg SERVER 0 www gpsgreat com 88 0 If set successfully you will receive the reply IP www gpsgreat com Port 88 6 2 2 Via IP SERVER 0 IP Port 0 Eg SERVER 0 58 64 200 64 88 0 If set successfully you will receive the reply IP 58 64 200 64 Port 88 6 3 Add specific number To set an SOS number you will need to set up the device via SMS Please send the following SMS SOS A No 1 No 2 No 3 A
8. e to the SOS number Eg Go out Fence Alarm Date Time 10 11 23 23 42 51 http maps google com maps q N23 E114 To set the vehicle s current position as the center of the fence please send command in this form FENCE ON 0 0 0 radius IN OUT H To close fence alarm function SMS FENCE OFF Note You can also set the Fence on the platform but only the platform will get the alarm message 10 Web based tracking The GPRS web based tracking platform allows real time tracking with the latest Google maps There is also a playback feature which allows you to view where the vehicle has been for the last 60 days making it ideal for fleet management 11 Trouble shooting 11 1 If after the first installation the device cannot connect to the platform server it will be shown as logged off on the platform Please check the installation of the tracker 1 Check whether the connection of power line is correct please do not connect it with the car control line 2 Check whether the SIM card is installed correctly please refer to the installation manual 3 Check whether the power switch is toggled to ON 4 Check whether ACC ignition cable is connected please turn on the ACC with your key after it is connected 5 Check the LEDs status If working the red LED is solid on the green LED and blue LED are also both solid on 6 Check whether GPS is located if not please drive to open areas for pos
9. ehicle is stationary 8 5 Restoring power Engine 8 5 1 Via phone Dial the number of the tracker via your land line telephone or mobile and press 4 in accordance with the voice instructions The power engine will be restored automatically 8 5 2 Via platform When the alarm is off send a power restoration command manually The tracker will restore the fuel supply and vehicle will work normally again A platform account and password is needed when sending a power cut off command 8 5 3 Via SMS Only a center number can send the command to the device to restore power The command is RELAY 0 After the command is carried out you will receive the SMS restore fuel supply success 9 Device alarms 9 1 SOS alarm In an emergency press SOS for 3 seconds to activate the SOS alarm The device will then send an SOS SMS to the specific preset numbers and then dial the numbers repeatedly until the call is through In the meantime the device will upload SOS alarm data to the server it will send SOS Alarm Date Time 13 08 22 23 42 51 http maps google com maps q N22 571490 E113 877103 Note The specific numbers should be preset please refer to 6 3 9 2 Wire cut off alarm When the electricity supply of device is cut off it will activate the cut off alarm In this case the device will send a related SMS to the specific numbers and dial the numbers repeatedly If nobody answers the call will loop 3 times
10. f your choice via your phone keypad Note Only SOS number can dial the number of device 8 1 Power on Power off Power on Having inserted a valid SIM card and connected all the wires turn on the device the Power LED will flash first whilst searching for signal the GSM and GPS LED will flash Once the GPS LED stays solid it means the device has been located and will start to work Power off Just turn off the power switch 8 2 Check location 8 2 1 Via phone Dial the number of the device via your land line telephone or mobile and press 2 according to the voice instructions the device will send a location message automatically Note The location SMS from device will only send to a mobile phone or telephone with SMS function It cannot be sent to a land line telephone without SMS capabilities 8 2 2 Via SMS 8 2 2 1 SMS WHERE to the SIM number of tracker The device will send a location message automatically You can get the coordinates Example Lat N22 571285 Lon E1 13 8771 15 Course 42 20 Speed 0 0740 DateTime 10 11 23 22 28 51 8 2 2 2 SMS URL to the SIM number of the tracker The device will send a location Google Map link Example lt Date Time 10 11 23 23 42 51 gt _http maps google com maps q N22 571490 E113 877103 8 2 3 Via platform Go to the platform website to check your vehicle location 8 3 Voice monitoring 8 3 1 Via Phone Dial the number of the tracker via your land line te
11. his case if the vehicle vibrates a few times it will activate the vibration alarm system If the vehicle battery is still not on ACC is at a low level after 3 minutes the device will start the vibration alarm SMS format DEFENSE TIME minutes The time ranges from 1 to 60 mins For example DEFENSE 15 This means that when ACC is at a low level for 15mins it will enter sensor alarm status vehicle power is off NOTE 1 Preset SOS numbers when sending SMS alarm messages 2 If there is no need for a vibration alarm please SMS SENSORSET 0 to stop it 6 9 Sensor detecting time and alarm delaying time setting For setting sensor detecting time and alarm delaying time please send command in this form SENSOR detecting time delaying time The range is 1 999s 10 300s For example If you send the command SENSOR 10 180 it will reply Sensor time interval 10 180 which means that once the device vibrates for 10s it will activate the vibration alarm unless the ACC is turned on in 180s 6 10 Restore to factory settings SMS command FACTORY to set all parameters to default factory settings You will receive an OK message via SMS if factory reset is successful 6 11 Reboot device When there is something wrong with the link of GPRS e g The parameter settings of the device are correct but you can t track the car on the platform You can send a command to the device to reboot The command
12. is RESET After receiving this command the device will reboot after 30 seconds 7 Parameter Checking 7 1 Check parameter settings Command the device via SMS to check the device settings Command format PARAM e g PARAM Reply information IMEI 500050300009180 IMEI number of the device GPRS Interval 10 GPS data uploading Interval the time ranges from 10 18000s default as 10s TIMESET 20 the GPS working time when ACC is OFF the time range from 1 999mins default as 20 min SOS Number 1 079xxxxxxxx 2 079xxxxxxxx 3 079xxxxxxxx a maximum three SOS numbers used for alarm Center Number 079xxxxxxxx only one center number used for cutting off and restoring oil command Sensor time interval 10 180 sensor detecting time default as 10s vibration alarm delay default as 180s the time ranges from10 300s Sensor alarm time interval 10 sensor alarm time interval the time ranges from 1 60mins default as 1Omins TimeZone E 8 set time zone default as E8 The SMS will be ordered as follows IMEInumber GPRSInterval TIMESET SOS CENTERnumber Sensortimeinter val Sensor alarm time Interval TimeZone 7 2 Check GPRS parameters SMS command format GPRSSET eg GPRSSET Reply message format GPRS ON GPRS on off status APN mobile o2 co uk 0 0 0 0 0 APN setting information Server www gpsgreat com 88 platform information URL http maps google com maps q preset web link setting information Overspeed 60 0 o
13. itioning 11 2 If it is offline on the platform First of all check the three LEDs status If these are not convenient to check please check the SIM card status 1 Call the SIM card number of the device to check whether you can get through 2 Check whether the vehicle is in a no GSM area such as a basement 3 Check the GSM GPS connection area and whether all other devices or a few of them are disconnected to make sure whether it is the fault of the mobile operator s connection 4 Check whether your SIM card needs topping up 5 Check whether the SIM card supports GPRS 6 Check the parameters setup whether the device IMEI number GPRS sending interval is correct 11 3 If the tracker s GPS function is normal but cannot be located for a long time please check whether the tracker has been installed correctly 1 Please make sure the GPS antenna is face up 2 Please make sure there is no electromagnetic wave absorbent object metal above the device especially thermal protective coating on the windscreen as this may affect the GPS reception of the device 11 4 If the GPS cannot receive signal normally e g there are high buildings around to interfere with GPS reception please drive to open areas for positioning Generally it needs 3 5 minutes to receive the first coordinates 11 5 If the GSM cannot receive the signal normally please check whether the SIM card is installed correctly or if there is GSM signa
14. l at the location you are e g basement parking please drive to a place with GSM signal reception 11 6 When an SOS mobile receives a tele cut off alarm SMS please check whether it is an illegal wire cut off or the FUSE on power line is blown If the FUSE in it is blown please contact your distributor to exchange with the same model FUSE Additional information There are many functions you can use on your web portal There is a playback feature which allows you to view where the vehicle has been for the last 60 days The Show LBS function on the top right corner of your portal tracks via the GSM base station This can be used when there is no GPS signal but when there is likely to be GPRS signal for example when the vehicle is in a garage or in a covered car park The tracker will be tracked by LBS sim card S means start P means parking Si Hill A fi Warranty card of GPS Vehicle tracker Special statement Specifications of this product subject to change without further notice Any change about the appearance and color is subject to the real object 1 2 3 Warranty card applies to the product with the IMEI number listed below 4 Please keep this card safely for after sale service as well as your receipt 5 Refer to the table below for the warranty reference This card is the basic certificate for warranty please fill it carefully and keep it safely CustomerName Phonemumber Cwtomeradares
15. lephone or mobile and press 1 in accordance with the voice instructions You will hear the voice around the device automatically Note The SIM card put into the device should have caller identification enabled 8 3 2 Via SMS After successfully receiving the message LISTEN the device will call back within a few minutes Just answer the phone and you will enter the voice monitoring state directly 8 4 Power Engine cut off 8 4 1 Via phone Dial the number of the tracker via your land line telephone or mobile and press 3 in accordance with the voice instructions The engine will be cut off automatically 8 4 2 Via platform Send an oil cut off command from the platform The tracker can only command to cut off oil when there is a valid GPS position You will need a platform account username and password to send an oil cut off command 8 4 3 Via SMS Firstly you should set a center number Only a center number can send the command to the device to cut off and restore oil The format is RELAY 1 After the command is carried out it will reply Cut off the fuel supply Success If the command was unsuccessful it will reply with the reason Notice After cutting off power the vehicle will be partly out of control so be more careful when using this function The engine can only be cut off if the speed of your vehicle is under 30km h and in safe position We advise that this function should only be used when the v
16. m SMS to the SOS number and dial the SOS numbers repeatedly until through If nobody answers the call will loop 3 times The tracking platform will also receive a vibration alarm message e g Vibrate Alarm Date Time 13 08 22 23 42 51 http maps google com maps q N22 571490 E113 877103 Note The specific numbers should be preset please refer to 6 3 SMS SENSORSET 0 to turn off the vibration alarm 9 5 Set speed alarm warning To set speed alarm function please send the following command to the device SPEED time speed the range of time is 1 10mins the unit of the speed is km h For example If you send the command SPEED 3 60 it will reply Over speed 60km h duration is 3min which means if the speed of the vehicle is over 60km h for more than 3mins it will send alarm message to SOS specific number Eg Over speed Alarm Date Time 13 08 22 23 42 51 http maps google com maps q N22 57 1490 E113 877103 To close the over set speed alarm function SMS SPEED 0 0 9 6 Fence alarm To set a fence alarm function please send the following command FENCE ON 0 latitude longitude radius IN OUT the unit of the radius is km For example If you send the command FENCE ON 0 23 114 10 OUT it will reply fence 23 114 radius 10km Out which means if the vehicle moves outside of the circle of which center is N23 E114 and the radius is 10km it will send alarm messag
17. means to add new numbers for example SOS A 07900000001 07900000002 07900000003 If there is only one SOS number you can appoint a specific number as SOS number The hash tag means that no number will be further added For example SOS A 07900000001 means to set the first number as SOS number SOS A 07900000002 means to set the second number as SOS number SOS A 07900000003 means to set the third number as SOS number If set successfully you will receive the following reply via SMS SOSnumber 07900000001 07900000002 07900000003 6 4 Delete specific number Before deleting a specific number please check its corresponding code For the code please send the following SMS PARAM to the device You will then be able to command the device to delete the number D means to delete the number for example SOS D 1 means to delete the first number SOS D 3 means to delete the third number If you want to delete more than one number you can send this command SOS D 1 3 means to delete the first and third numbers If you forgot the serial number of the mobile number you want to delete you can send this command SOS D mobile number and this will delete the mobile number directly For example SOS D 07900000001 means to delete the number 07900000001 directly After deleting the SOS number you will receive an ok message in reply having successfully deleted the specific number 6 5 Set the center number
18. moving it will activate the vibration alarm If there is no need for the theft proof function connect the ACC line to the positive in parallel and keep high level 5 1 3 Tele cut off petrol electricity control line yellow is connected to pin 86 of the Tele cut off petrol electricity relay equal to the yellow line of the relay socket 5 2 MIC line 2 pin Externally connect to microphone for voice monitor function 5 3 SOS line 2 pin Externally connect to SOS switch for SOS function 6 Parameter setting The SMS command format is not case sensitive and is divided by a comma You should receive a reply SMS after sending the command If set successfully there will be a corresponding reply SMS if not please set it again Any phone number can send an SMS command to the device as default 6 1 APN setting 6 1 1 Normally the device can search and set the APN automatically or it can be set manually The APN of many countries mobile networks are stored on the tracker for example For the UK we have included the APN of o2 VODAFONE and ORANGE If you choose to use one of these networks you do not need to set the APN manually When the sim card is inserted the device will recognise the network sim card and set the APN automatically If you wish to change your network and have a pre set APN you will first need to delete this before a different network sim card can be used To clear the current APN setting please SM
19. s Model Number Memme Date of Purchase mwoicemmber D C 1 The tracking device is guaranteed for one year for any manufacture fault 2 The below are not within the scope of the warranty 1 disassemble or maintain without authorisation 2 immersion break or burn of circuit board 3 damages from improper installation use maintenance or storage 4 damage of shell lens or internal antenna 6 IMEI number is torn or faded 7 warranty certificate is inconsistent with product model or the certificate is altered 8 damages due to force majeure Terms and Conditions for Sale of Goods of Knowledge Master UK Ltd applies Please visit our website www navigationmaster com Maintenance records Record one Mime ae o DO Maintenance status Record two j Minenanceunit me Fault description T DO
20. ver speed alarm setting information Fence Disable fence alarm setting information Call alarm Disable call alarm switch information 7 3 Check the mileage clear the mileage To check the mileage you can send this command GETMILEAGE You will receive a reply e g The total mileage is 252km which means the car has already been driven for 252km To clear the mileage you can send this command CMILEAGE You will receive the reply The total mileage is 0km 7 4 Check version To check the version of the device s software send this command VERSION You will receive a reply e g lt Version gt TRO6N V2 0 8 2013 7 30 7 5 Check the status To check the device s status you can send this command STATUS You will receive a reply e g Battery FULL GPRS Link up GSM Signal Level Strong GPS Successful Positioning ACC ON Defense OFF OilPowerControl ON Sensitivity of vibration 5 8 Operation of device New voice instructions for controlling main functions Use the SOS number to dial the number of the SIM card which is inserted in the device you will enable voice monitoring mode and will hear the following instructions for voice monitoring press 1 for track location message press 2 for cutting off the power engine and electric press 3 for restoring the power and electric press 4 for repeating the current directory press 0 to finish please hang up thank you Select the option o
Download Pdf Manuals
Related Search