Installation Instructions
Contents
1. switch from stream to spray E Press and hold PAUSE BUTTON 5 to temporarily stop flow from SPRAY 3 Release PAUSE BUTTON 5 to resume flow from 3 SPRAY 3 k a lt 1 J 5 ZF STREAM AERATOR 4 M965036 Rev 1 2 CHECK CONNECTIONS FOR LEAKS Move HANDLE down into off position Turn on water supplies and check connections for leaks m Operate HANDLE 2 up and down left and right to flush water lines thoroughly Operate HAND SPRAY and check connections for leaks 1 CHECK CONNECTIONS FOR LEAKS m m f faucet drips operate HANDLE several times from off to on Do not apply excessive force E Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then m Remove INDEX BUTTON 1 loosen HANDLE SCREW 2 and remove HANDLE 3 m Unthread the ESCUTCHEON CAP 4 Unthread three MOUNTING SCREWS 5 E Lift CARTRIDGE 6 off MANIFOLD 7 and remove CARTRIDGE SEALS 8 m Clean MANIFOLD 7 CARTRIDGE 6 ports and SEALS 8 m Place SEALS 8 into CARTRIDGE PORTS 6a m Place CARTRIDGE 6 onto MANIFOLD 7 and tighten MOUNTING SCREWS 5 alternately m Replace ESCUTCHEON CAP 4 HANDLE 3 tighten HANDLE SCREW 1 and install INDEX BUTTON 2 DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE2. Amirim Standard Installation Instructions COLONY SOFT 4175 300 Series SINGLE CONTROL KITCHEN PULL DOWN FAUCET Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly H H H Certified t ly with ANSI A112 18 1M please read these instructions carefully before you begin See OEE 036 Aey 4 2 RECOMMENDED TOOLS Regular Screwdriver Phillips Screwdriver Adjustable Wrench Plumbers Putty or Caulking INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON BAN or e A Installation with ESCUTCHEON 1 Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE 1 Insert SUPPLY HOSES 2 SPRAY HOSE 9 and SHANK 3 through hole of ESCUTCHEON with PUTTY PLATE 1 and mounting surface Follow mounting instructions below to secure faucet to mounting surface B Installation less ESCUTCHEOW 1 Discard ESCUTCHEON with PUTTY PLATE 1 Insert supply HOSES 2 SPRAY HOSE 9 and SHANK 3 through mounting hole and seat SPOUT BASE onto sink or mounting surface Do not use putty Insert HOSES 2 through RUBBER WASHER 4 BRASS WASHER 5 and threaded LOCKNUT 6 Assemble RUBBER WASHER 4 BRASS WASHER 5 and threaded LOCKNUT 6 onto SHANK 3 from underside of sink or mounting surface Hand tighten LOCKNUT 6 Use a screwdriver to tighten SCREWS 8 on LOCKNUT 6 Work your way around LO
3. CKNUT 6 tightening the screws slightly each time until all are snug to ensure even pressure SPOUT BASE _ o o SPOUT BASE _ dBS NA lt gt SINK OR MOUNTING SURFACE 2 MAKE WATER SUPPLY CONNECTIONS Turn off hot and cold water supplies before beginning Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left supply Marked with a Red Stripe to Hot and right supply Marked with Blue Stripe to Cold wall supply Use adjustable wrench to tighten connections Do not over tighten Faucet supplies are 21 long from faucet base Note If additional supply length is required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are too long loop as illustrated to avoid kinking INSTALL WEIGHTS With HAND SPRAY 1 seated in SPOUT 2 install two sets of WEIGHTS 4 onto HOSE 3 using two SCREWS 5 Locate the WEIGHTS 4 16 inches from the underside of the sink deck Tighten SCREWS 5 firmly 4 TEST INSTALLED FAUCET m Move HANDLE 1 into off m With HANDLE 1 in off position position unthread SPRAY 3 from HOSE 2 m Turn on water supplies Operate handle back to front in COLD and HOT positions to flush water lines m Check connections for leaks thoroughly See Section 5 E Replace SPRAY 3 onto HOSE 2 SPRAY OPERATION m With FAUCET on press TOGGLE BUTTON 4 on SPRAY 3 to
4. SURFACE M965036 Rev 1 2
Download Pdf Manuals
Related Search