User Manual
Contents
1. Crane Scale C A STO N III OWNER S MANUAL 9007 CT3 0033 1 2004 5 PRECAUTIONS hh 4 PREFACE 7 7 ee 9 OPERATION a 10 FUNCTIONS amp DESCRIPTIONS 10 1 ZERO FUNCTION 10 2 TARE FUNCTION 10 3 HOLD FUNCTION 11 4 FUNCTION OF REMOTE CONTROL 11 USE OF BATTERY CHARGER 12 SPECIFICATIONG 12 PRECAUTIONS To installate safety pin in hook should be fixed to prevent dropping out eye bolt ZN Warning Do not overload beyond the maximum Scale must be grounded to minimize electricity static This will minimize defect or electric shock Do not disassemble the scale When any damage or defect occurs contact your CAS authorized dealer immediately for Do not pull the plug by its cord when To prevent from fire occurring Do not To reduce electric shock or incorrect unplugging Damaged cord could cause place or use the scale near reading Do not spill water on the scale electric shock or fire flammable or corrosive or place it in humid condition Avoid placing the scale near heater Use proper Adapter Incorrect adapter Insert plug firmly to wall outlet to or in direct sunlight could damage the scale prevent electric shock Do not stand under the scale while weighing the load and you should be careful to provide against safety accident A Attention For consistent and accu2. before shipping m Insert charger A C cord into the power source and connect the discharged battery to the connector m Turn ON the switch on the battery charger charging will start with RED lamp CHARG turn on m When the charging is complated GREEN lamp FULL turns on Estimated time for charging is 8 hours Charging time can be vary according to the battery condition SPECIHCATIONS MODEL CASTON REMOTE CONTROL POWER 3V 1 5V AMM 2 CASTON SIZE GO TON 50 TON DA I A UNIT mm MODEL MAX CAPA DIVISION A B C F WEIGHT zomo zoron 10g 725 so orzo sm e0 rogo Notice S pecifications are subject to change for improvement without notice
3. g display m ZERO Same as keyboard m TARE Same as keyboard m HOLD Same as keyboard mSET CLEAR Used to clear previously added weight m SUM Used to add weight JENN MAX 50069 CAPACITY S000XEks MIN 200kg D p NOTE To cut power completely from scale you must use main power switch on rear of scale m DISPLAY WEIGHT DISPLAY Displays weight or messages ZERO LAMP Indicates that scale is stable and at zero m Open the battery lid located in back of the scale and turn main power switch off TARE LAMP Indicates that scale is currently using a tare m Separate the battery connector and take out the discharged battery HOLD LAMP Indicates that the HOLD feature has been activated m Put a charged battery in rear and connect the battery connector LOW BATTERY LAMP Indicates that battery is low and must be changed soon Turn main power switch on and cover the battery lid m KEY FUNCTIONS BATTERY CONNECTOP KEYS FUNCTIONS Used to tum the scale ON Used to turn the scale OFF BATTERY BOLT A HP EERE 7 lt gt W Resets scale to zero FIG 1 CLOSE STATE FIG 2 OPEN STATE OPERATION m Press the ON key located in front of the scale The scale will perform self test on the WEIGHT DISPLAY and will be ready for weighing when zero lamp is on While the power is off the ON OFF key on the remote control wo
4. rate reading Avoid sudden shock to the scale Take the battery out when scale is not in maintain periodical check by your Internal mechanism could be damaged use for long time Leakage from the CAS authorized dealer batteries is hazardous 9 U Place the scale on firm and temperature Keep the scale away from other consistent environment electromagnetic generating devices This may interfere with accurate reading If you don t use the scale for a long tine you should tum off POWER SAW on the rare panel WARNING The load which hang on the hook should be WARNING a vertical load Refer to the next features m The load which hang on the hook should be a vertical load PREFACE We greatly appreciate your purchase of the CASTON These goods perform excellently and exhibit splendid properties through strike tests The CASTON is delicately designed to coincide with the special requirements of several industrial fields and includes many functions and various external interfaces Also it 1s programmed for the user s convenience and contains display functions that are easily accessible Before using The CASTON it is recommended that you read this manual carefully so you may use this device to its full potential LIFT EYE DISPLAY LOW BATTERY LAMP KEYBOARD DISPLAY amp KEYBOARD Remote Control m ON OFF Does not turn scale OFF only saves power by pausin
5. rn on m If you weigh unstable things in Auto hold mode Hat will display on the Weight Display And then the average value of the weight fluctuation will display m The weight will remain on display even if the weight 1s removed To delete holded value press the HOLD key again m escape from Auto hold mode press the HOLD key when the hook is empty The message HEI d will be displayed and HOLD lamp turning off Manual Hold Function Execute when you press HOLD key m Press the HOLD key while weighing an unstable item hang will display and then the average value of the weight fluctuation will display on the Weight Display m Toescape from this mode press the HOLD key again Then the scale changes from Hold mode to Normal mode 4 FUNCTION OF REMOTE CONTROL m Key functions of remote control are the same as those of the scale key board m SUM FUNCTION Press SUM key when a thing is hang on the hook in weighing mode Then the scale will change weighing mode to sum mode and will add old and new weights This added weighing value will be memorized and displayed on the WEIGHT DISPLAY m To clear the added weights press SUM key in weighing mode and the scale will change to sum mode m Press SET CLEAR key and then the scale will clear the added weights m To escape from this sum mode press SUM key again USE OF BATTERY CHARGER m Check the voltage of battery charger before use It is fixed to 220V
6. uldn t operate m Use the ON OFF key on the remote controller when the power is on Hook should be empty FUNCTIONS amp DESCRIPTIONS 1 ZERO FUNCTION Used to correct drifted zero value when the scale 15 unloaded You can adjust the zero up to 2 of the maximum capacity and motion is not detected m The function works when ZERO key is pressed and the ZERO LAMP is on m Example If the weight has drifted you can press ZERO key to bring back to the zero 20kg on weight display will go to Okg when you press the ZERO key 2 TARE FUNCTION m Tare is the weight of container being used for a commodity The TARE key subtracts the weight of the container m After hanging a weight to be tared on the HOOK press the TARE key Then the scale will memorize the weight of the tare and will display zero value 0 The TARE lamp will be on m If you weigh items you will see the net weight To release this function remove everything from the hook and press the TARE key Then the TARE LAMP will turn off and this function is terminated NOTE The weight including TARE weight can t exceed the maximum capacity 3 HOLD FUNCTION Automatic Hold Function This function is performed whenever you weigh an item m Press the HOLD key when the hook is empty In zero value condition m The Weight Display will display HE w sequentially m The scale will change from the Normal mode to Auto hold mode and HOLD lamp will tu
Download Pdf Manuals
Related Search