Mirage™ FX for Her User Manual
Contents
1. Manufacturer ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia Distributed by ResMed Corp 9001 Spectrum Center Boulevard San Dieago CA 92123 USA ResMed UK Ltd 96 Milton Park Abingdon Oxfordshire 0X14 4RY UK See www resmed com for other ResMed locations worldwide irage FX Protected by patents AU 785376 DE 20122844 0 EP 1314445 EP 1582230 HK 1057714 JP 4354664 US 6581594 US 6823865 US 7159587 Other patents pending Design registrations pending irage is a trademark of ResMed Ltd and is registered in U S Patent and Trademark Office 2010 ResMed Ltd 628013 1 2010 12 MIRAGE FX for HER USER DRM AMER ENG Reno Global leaders in sleep and respiratory medicine www resmed com2. fitting illustrations section in this user guide show the sequence for obtaining the best fit and comfort when using your mask Fitting steps Prior to fitting your mask remove the elbow from the mask by pressing the side tabs Connect the elbow to your device air tubing 1 With both lower headgear straps released hold the mask against your face and pull the headgear over your head Bringing the lower straps below your ears loop the headgear into the lower hooks on the mask frame Unfasten the Velcro pull the upper headgear straps evenly until they are comfortable and reattach the Velcro Repeat step 3 with the lower headgear straps Attach the combined elbow assembly and air tubing to the mask by pressing the side tabs and pushing into mask frame Your mask and headgear should be positioned as shown Ensure the headgear label is facing outwards Removing the mask Refer to the removal illustrations section in this user guide To remove your mask disconnect one of the lower headgear hooks and pull the mask and headgear up over your head Disassembly Refer to the disassembly illustrations in this user guide Disassembly steps 1 Unhook the upper headgear straps from the mask frame there is no need to undo the Velcro Remove the combined elbow assembly and air tubing from the mask by pressing the side tabs and pulling away from the mask frame Remove the elbow assembly from the air tubing Gently
3. to the reassembly instructions Weekly Handwash the headgear English A WARNING Do not use aromatic based solutions or scented oils eg eucalyptus or essential oils bleach alcohol or products that smell strongly eg citrus to clean any of the mask components Residual vapours from these solutions can be inhaled if not rinsed thoroughly They may also damage the mask A CAUTION If any visible deterioration of a system component is apparent cracking crazing tears etc or if after cleaning any component remains unclean the component should be discarded and replaced Reprocessing the mask between patients This mask should be reprocessed when used between patients Cleaning disinfection and sterilization instructions are available from the ResMed website www resmed com masks sterilization americas If you do not have internet access please contact your ResMed representative Troubleshooting Problem possible cause Solution Mask is too noisy Vent is blocked or partially blocked If the vent requires cleaning use a soft bristle brush Elbow incorrectly inserted Remove the elbow from the mask and then reassemble according to the instructions Mask leaks around the face Mask not positioned correctly Gently pull the cushion away from the face to reinflate Reposition your mask according to the instructions Air leaking around the bridge of the nose Mask is not tightened correctly Tighten top headgear
4. RESMED Mirage FX for Her NASAL MASK User Guide English RESMED Mirage FX for Her KX only NASAL MASK Fitting Ajustement Colocaci n Coloca o e ajuste 1 a M 2 Removal Retrait Remoci n Remo o Reassembly Remontage Montaje Remontagem 1 Mirage FX for Her A Mask components Composants du masque Piezas de la mascarilla Componentes da mascara Item Article Art culo Item 1 Description Description Descripci n Descri o Mask frame Entourage rigide Armaz n de la mascarilla Arma o da m scara Forehead support Support frontal Apoyo para la frente Suporte para a testa Cushion Bulle Almohadilla Almofada Vent Orifice de ventilation Ventilaci n Respiradouro Headgear Harnais Arn s Arn s Elbow assembly Ensemble coude Conjunto del codo Conjunto do cotovelo Elbow side tabs Pattes d attache lat rales coude Leng etas laterales del codo Abas laterais do cotovelo Complete system Syst me complet Sistema completo Sistema completo Frame system Entourage complet Sistema de armaz n Sistema da arma o Part number Code produit N mero de pieza N mero da pe a 62111 62129 62128 62112 Mirage FX for Her NASAL MASK Thank you for choosing the Mirage FX fo
5. conditions of normal use ResMed will repair or replace at its option the defective product or any of its components This limited warranty does not cover a any damage caused as a result of improper use abuse modification or alteration of the product b repairs carried out by any service organization that has not been expressly authorized by ResMed to perform such repairs and c any damage or contamination due to cigarette pipe cigar or other smoke Warranty is void on product sold or resold outside the region of original purchase Warranty claims on defective product must be made by the initial consumer at the point of purchase This warranty replaces all other expressed or implied warranties including any implied warranty of merchantability or fitness for a particular purpose Some regions or states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you ResMed shall not be responsible for any incidental or consequential damages claimed to have resulted from the sale installation or use of any ResMed product Some regions or states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from region to region For further information on your warranty rights contact your local ResMed dealer or ResMed office inal
6. his product does not contain natural rubber latex e The manufacturer reserves the right to change these specifications without notice Storage Ensure that the mask is thoroughly clean and dry before storing it for any length of time Store the mask in a dry place out of direct sunlight Disposal This mask does not contain any hazardous substances and may be disposed of with your normal household refuse Symbols The following symbols may appear on your product or packaging A Caution consult accompanying documents LoT Lot number R m F Part number a Temperature limitation S Humidity limitation amp Does not contain natural rubber latex qual Manufacturer Indicates a Warning or Caution and alerts you to a possible injury or explains special measures for the safe and effective use of the device a Keep away from rain tt This way up 5 Fragile handle with care kR Prescription only In the US Federal law restricts these devices to sale by or on the order of a physician English Limited warranty ResMed Ltd hereafter ResMed warrants that your ResMed mask system including mask frame cushion headgear and tubing shall be free from defects in material and workmanship from the date of purchase for the period of 90 days or in the case of disposable masks the maximum use period This warranty is only available to the initial consumer It is not transferable If the product fails under
7. or details on settings and operational information e Ata fixed rate of supplemental oxygen flow the inhaled oxygen concentration varies depending on the pressure settings patient breathing pattern mask point of application and leak rate Technical specifications Pressure flow curve The mask contains passive venting to protect against rebreathing As a result of manufacturing variations the vent flow rate may vary Pressure Flow E cm H O L min E a 4 19 e g 8 28 3 E 12 34 o a 16 40 Mask pressure cm H 0 20 45 Dead space Physical dead space is the empty volume of the mask information to the end of the swivel It is 93 mL Therapy 4 to 20 cm H O pressure Resistance Drop in pressure measured nominal Environmental conditions Gross dimensions at 50 L min 0 2 cm H O at 100 L min 1 0 cm H O Operating temperature 41 F to 104 F 5 C to 40 C Operating humidity 15 to 95 non condensing Storage and transport 4 F to 140 F 20 C to 60 C Storage and transport humidity up to 95 non condensing Mask fully assembled with elbow assembly no headgear 5 43 H x 3 38 W x 3 46 D 138 mm H x 86 mm W x 88 mm D Mask setting For S9 Select NASAL options For other devices Select STANDARD otherwise select VISTA as the mask option Notes e The mask system does not contain PVC DEHP or phthalates e T
8. r Her Please read the entire manual before use Intended use The Mirage FX for Her channels airflow noninvasively to a patient from a continuous positive airway pressure CPAP or bilevel device The Mirage FX for Her is e to be used by patients gt 66 Ib 30 kg for whom positive airway pressure has been prescribed e intended for single patient re use in the home environment and multipatient re use in the hospital institutional environment Ax WARNING The vent holes must be kept clear e The mask should not be used unless the device is turned on Once the mask is fitted ensure the device is blowing air e Follow all precautions when using supplemental oxygen e Oxygen flow must be turned off when the CPAP or bilevel device is not operating so that unused oxygen does not accumulate within the device enclosure and create a risk of fire e Remove all packaging before using the mask Using your mask When using your mask with ResMed CPAP or bilevel devices that have mask setting options refer to the Technical specifications section in this user guide for mask setting options For a full list of compatible devices for this mask see the Mask Device Compatibility List on www resmed com on the Products page under Service amp Support If you do not have internet access please contact your ResMed representative Note If you experience nasal dryness or irritation using a humidifier is recommended English Fitting The
9. separate the cushion from the mask frame Reassembly Refer to the reassembly illustrations in this user guide Reassembly steps 1 Ensure the cushion is oriented correctly by aligning the top cushion tab with the recess in the top of the mask Gently pull the cushion through the front of the mask frame until the cushion locks securely into the mask frame The tabs on either side of the cushion should be sitting against the mask frame Ensure the cushion is not twisted or distorted Attach the top headgear straps to the mask frame by looping onto each of the upper headgear hooks Replace the elbow assembly into the air tubing and attach the combined elbow assembly and air tubing to the mask by pressing the side tabs and pushing into the mask Cleaning your mask in the home Your mask and headgear should only be gently handwashed Daily After each use Disassemble the mask components according to the disassembly instructions Thoroughly clean the separated mask components excluding headgear by gently rubbing in warm approximately 86 F 30 C water using mild soap To optimize the mask seal facial oils should be removed from the cushion after use Use a soft bristle brush to clean the vent Inspect each component and if required repeat washing until visually clean Rinse all components well with drinking quality water and allow to air dry out of direct sunlight When all components are dry reassemble according
10. straps 4 Air leaking around the sides of the nose Mask is not tightened correctly Tighten both upper and lower headgear straps Turn off the CPAP or bilevel device and remove mask Refit the mask according to the instructions Ensure you position the cushion correctly on the face before pulling headgear over the head Do not slide mask down the face during fitting as this may lead to folding or curling of the cushion The mask does not fit properly Mask is incorrectly assembled Disassemble the mask then reassemble according to the instructions Cushion may be dirty Clean cushion according to the instructions A WARNING The technical specifications of the mask are provided for your clinician to check that they are compatible with the CPAP or bilevel device If used outside specification or if used with incompatible devices the seal and comfort of the mask may not be effective optimum therapy may not be achieved and leak or variation in the rate of leak may affect the CPAP or bilevel device function Discontinue using this mask if you have ANY adverse reaction to the use of the mask and consult your physician or sleep therapist Using a mask may cause tooth gum or jaw soreness or aggravate an existing dental condition If symptoms occur consult your physician or dentist As with all masks some rebreathing may occur at low CPAP pressures English e Refer to your CPAP or bilevel device manual f
Download Pdf Manuals
Related Search