Home

VersiVision

1. www versitron com FVCM12 Back Circuit Board The back circuit board of the chassis is solely designed for the purpose of distributing voltage to each plug in module A 32 pin female connector is provided from the backboard for each slot in the chassis supplying the 12 VAC power source This is the only electrical connection from the back circuit board to the unit Plug In Modules Plug in modules are installed by sliding the module into a pair of top and bottom card guides in any available slot in the chassis The module should be pushed in completely so that 32 pin male connector on the rear of the chassis engages the 32 pin female connector on the back plane In addition the plug in module is fastened into place by tightening the two captive panel screws into the appropriate mating sockets with a small flat blade screwdriver Each plug in module is equipped with a red LED which will illuminate when power is correctly supplied to the module The failure of any module in the chassis will not disable the entire chassis Troubleshooting If the power lamp on the back panel fails to light please check whether the line cord is properly connected If there is power on the line cord check the fuse located in the fuse container under the red lamp button on the back panel of the unit As a final solution replace the power supply If the power LED indicator on all plug in modules fails to light check the unit using the following steps 1
2. V veRsITRON Your Copper to Fiber Connection VersiVision FVCM12 12 SLOT RACK MOUNT CHASSIS USER S MANUAL Revision B February 2006 VERSITRON Inc 83 Albe Drive Suite C Newark DE 19702 FVCM12 PROPRIETARY DATA All data in this manual is proprietary and may not be disclosed used or duplicated for procurement or manufacturing purposes without prior written permission by VERSITRON WARRANTY All VERSITRON products purchased after January 2001 carry a limited lifetime warranty against defects in materials and workmanship for the lifetime of the product Purchases made prior to January 2001 are warranted for a period of one year from date of delivery VERSITRON reserves the right to repair or at our option replace parts which during normal usage prove to be defective during the warranty period provided that 1 You call VERSITRON at 302 894 0699 or 800 537 2296 and obtain a RMA Return Authorization Number Please reference your RMA number on the outside of the box in which the item is returned 2 Shipping charges are pre paid No other warranty is expressed or implied and we are not liable for consequential damages For repairs outside of the warranty period the same procedure must be followed www versitron com FVCM12 Introduction The VERSITRON VersiVision FVCM12 Rack Mount Chassis can fully accommodate the combination of up to twelve 2 channel or 4 channel video and or video data modules The
3. chassis employs a 110 VAC Switch Mode Power Supply SMPS design reducing the possibility of a single point of failure that can cause a complete shutdown or a major fault of other modules within the chassis rack The high stability of the system ensures that if only one module shuts down the operation of the other modules remains unimpaired Two air cooling fans are installed inside to further strengthen the long reliability of the system and eliminate the necessity of periodic maintenance In addition all the modules inserted in the chassis are hot swappable As a result it is unnecessary for the users to power down the chassis when removing or replacing a module Technical Specifications e Input Voltage 110VAC e Power Supply 12VAC 500mA e Filter Form AC DC Filtering e Slots 12 e Size 18 97 x 11 81 x 7 09 Inches e Air Cooling Fan Two e Fan Power Supply 12VDC 0 23A e Power Consumption 3W e Construction Aluminum e Finish Black Paint e Operating Temperature 30 C to 50 C e Storage Temperature 40 C to 85 C Power Supply The standard power supply for FVCM12 is 110VAC which is connected through an attached line cord A standard 32 pin connector supplies the power to each module in the chassis The connector is installed such that the notch matches with the 32 pin female connector on the back plane The red input lamp on the back panel illuminates when the power supply is properly connected to the unit
4. The power lamp button on the rear panel lights 2 The 32 pin male connector on the rear of each module is firmly connected to its mating connector on the back plane If the unit still fails to work normally after confirming the above steps the chassis should be replaced If the power LED on an individual plug in module fails to light check the unit using the following steps 1 The plug in module should be firmly seated into the female connector on the back circuit board 2 The fuses in the fuse container under the red lamp button should be intact If not return the module for maintenance www versitron com FVCM12

VersiVision

Contents

Download Pdf Manuals

Related Search

Related Contents