USER MANUAL
Contents
1. Viscosity Grade ISO VG 22 Oil vibration element SAE 10W 30 Hydraulic Oil Level Check Check every day that the hydraulic connections do not leak or wear during operation Check the oil level with the dipstick on the top of the tank The level must be between MIN and MAX Fill up when reguired spac101 FB165 FB 225 FB 250 AN spac103 Oil level Engine power switch Closed Open Full RPM Idle Fuel cock Choke Throttle lever FB 225 Throttle lever FB 165 BEFORE STARTING AFTER STARTING See Daily Checks on page 8 Switch the throttle lever to idle STARTING Petrol Engine FB 225 Oper tie choke eraually Run the engine warm for around 5 minutes Switch the engine power switch to 1 Open the fuel cock STOPPING piel merely Leven MIN Switch the engine to idle and let it run for a few Adjust the choke If the engine is cold close the choke Gantan completely Do not use the choke ifthe engine is warm er itch th i itch to 0 or if the air temperature is high eile IR EEE Dower neo Start by pulling the Close the fuel cock starting handle Pull it first until the mecha nism engages Then pull it hard and fast Dok 101489B GB 0925 10 Swe moc INTERNATIONAL AB Dok 101489B GB 0925 FB 165 FB 225 FB 250 spac104 spac108 Charging lamp and Fuel cock2. The machine consists of a base plate with a vibration element and an upper part cushioned from the base plate The cushioning between the base plate and the upper part consists of rubber dampers The power is transmitted from the engine to the vibration element via a V belt which can be adjusted with a belt tensioner The engine V belt pulley is fitted with an integrated centrifugal clutch which allows the engine to be started and run idle without the vibrator being connected The engine is well protected against damage in connection with use and transportation by a sturdy protective frame with a protective panel Dok 101489B GB 0925 Dok 101489B GB 0925 TECHNICAL DESCRIPTION FB 165 FB 225 FB 165 FB 225 FB 250 2 A DARAS pS Ea a BOY AR PIN NO HyS SWEPRODC INTERNATIONAL AB Control handle Forward reverse control Lifting eye Centrifugal clutch V belt Vibration element Base plate Rubber damper Engine plate Petrol engine Transport locking device Throttle lever Control handle Forward reverse control Lifting eye Centrifugal clutch V belt Vibration element Base plate Rubber damper Engine plate Diesel engine Transport locking device Throttle lever FB165 FB 225 FB 250 DAILY CHECKS Air Filter Check The air filter must be checked at least once every Fuel Check working week When working in dusty conditions Check that there is fuel in the tank Top up if necessary ch
3. increased comfort i o Push the button 1 to activate the heated handle The machine has a lifting eye that can be used for a hook or hawser spac109 Check before lifting that the lifting eye and its mounting on the machine are undamaged Check also that the base plate s rubber dampers are undamaged Polyuretan Pad and firmly attached A polyuretan pad is used for stone paving work to protect against stones and ground clinker For transportation by vehicle the handle must be folded forwards and locked with the transport locking device The machine must then be secured with for example approved straps Note Secure it by the base plate and not the rubber cushioned upper part 14 Swe moc INTERNATIONAL AB Dok 101489B GB 0925 Dok 101489B GB 0925 FB 165 FB 225 FB 250 SWERODC INTERNATIONAL AB SWEeERNOC INTERNATIONAL AB SWEPAC INTERNATIONAL AB Address Box 132 341 23 Ljungby Sweden tel 46 0 372 156 00 fax 46 0 372 837 41 E mail mail swepac se
4. M Then let It go Charging lamp and engine start switch spac105 Charging lamp and engine start switch key spac106 Manual start STOPPING Switch the engine to the idle position idle let it run for a few minutes then switch it to stop Yanmar Never switch the engine off with the decompression handle Switch the engine power switch to 0 Close the fuel cock HATZ Turn the key A whistlesignal is heard if the key is in the ignition position 12 SWEPRODC INTERNATIONAL AB Dok 101489B GB 0925 Dok 101489B GB 0925 FB 165 FB 225 FB 250 OPERATING INSTRUCTIONS The machine s vibration elements start when the throttle is increased The best packing is achieved at full engine RPM Avoid running the engine at other RPM The machine s vibration element stops when the throttle lever is switched to stop To move forwards do not touch the forward reverse control To reverse pull the hoop towards the control handle Reversing The machine is only designed to be used outdoors Work with the machine in daylight or other adequate lighting Ballast must be wetted or naturally damp All other use is discouraged NOTE When moving up a slope the machine should be reversed The machine may not incline more than 20 when in use or parked spac110b spac110a SWERDC 13 INTERNATIONAL AB FB165 FB 225 FB 250 Handle heater TRANSPORTATION FB 250 has a heated handle for
5. SuWURPOC FB 165 FB 225 INTERNATIONAL AB FB 250 USER MANUAL Dok 101489B GB 0925 FB165 FB 225 FB 250 SWERODC INTERNATIONAL AB Dok 101489B GB 0925 Dok 101489B GB 0925 FB 165 FB 225 FB 250 USE SWEPAC FB165 FB 225 FB 250 are used to pack ballast under foundations in connection with road building in trenches etc On account of the forward reverse function the machine is very suitable for packing in tight spaces and as a complement to larger packing equipment in places with poor access CONTENTS USE T 3 SAFETY INSTRUCTIONS 4 STANDARDS nennen 4 SIGNS een 5 TECHNICAL DATA aan 6 METHOD OF OPERATION 6 TECHNICAL DESCRIPTION usa 7 DAILY CHECKS css 8 BEFORE STARTING eee 10 STARTING petrol engine rad 10 AFTER S PAR TEINI sees ee eenn 10 STOPPING aaa 10 BEFORE STARTING nee 11 STARTING diesel engine sushi 11 MANUAL STAR Tol rias 12 STOPPING escarnio bado alaban uds 12 OPERATING INSTRUCTIONS sese 13 TRANSPORTATION aussen 14 SWERDC INTERNATIONAL AB FB165 FB 225 FB 250 SAFETY INSTRUCTIONS e Before using the machine the operator must be in formed of the manufacturer s safety instructions and instructions for use The machine may only be used outdoors The machine may not be used if protection and sa fety devices are not present or not working The operator may not leave the machine unattended when the engine is on When the vibrator is con
6. ax engine power 7 Max weight 8 Serial number Engine and silencer to avoid burns or discomfort do not touch hot engine parts when the engine is on or when the machine has recently been used Belt drive Keep hands tools and other objects away from the belt drive when the machine is on to avoid injury and damage See the safety instructions in the manual As the sound pressure level at the operator s ears exceeds 85 dB A ear protectors must be used when working with the machine to prevent hearing damage SWERODC INTERNATIONAL AB FB165 FB 225 FB 250 TECHNICAL DATA FB 165 Net Weight iwsitsssasvsitasesus taasta 160 kg Base plate w x 430 x 720 mm PSO een rieleele approximately 25 m min Permitted inclination 20 Centrifugal force 32 000 N Vibration frequency 82 Hz Drive engine Honda GX 200 Engine power 4 9 kW Engine RPM cenee 3300 RPM Fuel tank volume 3 6 liter UCL AY PC arst H Unleaded petrol 95 98 octane Oil quantity crankcase 0 6 liter Oil quantity vibration element 0 4 liter FB 250 Yanmar ESA 265 kg Base plate W x 1 550 x 790 mm ele nen es kukeks kaka approximately 25 m min Permitted inclination 20 Centrifugal force 40 000 N Vibration frequency 80 Hz Di
7. eck daily Engine Oil Level Check Check the oil level in the crankcase every day The RA i Honda oil must reach the edge of the filling hole when the machine is on a level surface Y aas MO wis 1 Paper element 2 Foam plastic element Oil Fuel Leakage Check every day that the engine is not leaking oil or fuel If a leak is discovered the machine may not be operated until the fault has been remedied avhj lpts Yanmar A spac102 Cleaning 1 Remove the foam plastic element and the paper ele ment and check that they are undamaged Replace damaged parts 2 Wash the foam plastic element in liquid with a high flashpoint and let it dry properly Dip in engine oil and squeeze dry 3 Strike the paper element against a hard object a few times to loosen any dirt 8 SWEPRODC INTERNATIONAL AB Dok 101489B GB 0925 Dok 101489B GB 0925 V belt Drive Check the tension and condition of the V belt regularly FB 165 FB 225 FB 250 Replace a damaged V belt with the new type B 35 for FB 225 FB250Yanmar B34 for FB250Hatz and B33 for FB165 Rubber Dampers Check the condition of the rubber dampers regularly Replace damaged dampers SWEPRODC INTERNATIONAL AB Fuel and oil recommendations Fuel petrol engine Unleaded petrol or alkylate Fuel diesel engine Diesel Engine Ol veria taras SAE 10W 30 Hydraulic oil
8. engine start switch spac105 spac107 Throttle lever Charging lamp and engine start switch key BEFORE STARTING FB 250 Yanmar See Daily Checks on page 8 Note Never run the starter motor for longer than 10 seconds at a time Ifthe engine does not start wait 15 seconds before trying to start it again Open the fuel cock Switch the engine power switch to 1 Switch the engine to the idle position idle Push the start button STARTING FB 250 HATZ Electrical Starter Switch the throttle lever to MIN A whistle signal is heard when the key is turned to the ignition position Indicator light for battery charging lights up Push in the key and turn it The key springs back after starting SWEPROC INTERNATIONAL AB FB165 FB 225 FB 250 spac104 spac107 Throttle lever Decompression handle Handstart HATZ Turn the key to the ignition position Pull the starter cord as far as it will go Letthe cord go back in Handstart Yanmar Press the decompression handle down The handle must remain in the depressed position Switch the engine power switch to 1 Take hold of the starter cord with both hands and pull hard In very cold weather or if the battery capacity is low for a different reason starting can be facilitated using the decompression device in connection with the valve housing Press the lever down and hold it down until the flywheel has reached its maximum RP
9. level Lu Guaranteed 105 dB A 108dB A 108 dB A 108 dB A sound power level L As the sound pressure level at the operator s ears exceeds 85 dB A ear protectors must be used during operation Hand arm vibrations The vibration acceleration was measured in accordance with the ISO 5349 standard during operation on a surface of macadam The measurement values were translated into the maximum daily exposure time for regular usage For additional information about vibrations please confer the regulation AFS 2005 15 from the Swedish Work Environment Authority FB 250 FB 250 Hatz Yanmar The maximum daily exposure time Exhaust Emissions The FB165 FB 225 meet the requirements for exhaust emissions in accordance with EU Directive 2002 88EC stage 2 The FB 250 meet the requirements for exhaust emissions in accordance with US CARB stage 1 Dok 101489B GB 0925 4 SURPOC INTERNATIONAL AB Dok 101489B GB 0925 FB 165 FB 225 FB 250 SIGNS Warning Signs Machine Signs SWEACIC wunesy SWEDEN 8 INTERNATIONAL AB MODEL SERIAL NO MANUFACTURED Before use carefully read the manual and its safety ki A instructions so that you can handle the machine safely Ensure that the manual is always accessible 7 6 1 Manufacturer 2 Place country of manufacture AA WARNING 3 CE mark 4 Model name 5 Year of manufacture 6 M
10. nected the operator must be able to control the mo vement of the machine using the control handle and the start stop controls The machine may be operated only by a trained operator e During maintenance work or other interventions in the machine the engine must always be off e Switch the engine off before adding fuel Avoid fuel spillage and immediately wipe off any spilled fuel Add fuel only in well ventilated areas e Avoid touching hot engine parts for example the silencer e Before lifting the machine check that the lifting de vice and its mounting are not damaged and that the rubber dampers on the base plate are undamaged and tightened During transportation and storage the fuel tank should be empty and the fuel cock switched off e When the machine is parked ensure that it cannot tip over The machine may not incline more than 20 The operator must use ear protectors when working with the machine The operator must ensure that no unauthorised per sons are in the immediate vicinity ofthe machine STANDARDS Noise Measurement in accordance with the standard EN 500 4 Rev 1 1998 Annex C In accordance with the conditions in Directive 2000 14 EC Annex VI the following values are reported FB 250 FB 250 Hatz Yanmar Sound 91 dB A 95dB A 95 dB A 95 dB A pressure level at the operator s ears LpA Permitted 108 dB A 108 dB A 108 dB A 108 dB A sound power
11. ye engine onasan Yanmar L70N Engine poWer 4 5 kW Engine RPM nenne 3200 RPM Fuel tank volume 3 5 liter Fuel type ana Diesel MK1 Oil quantity crankcase 1 1 liter Oil quantity vibration element 0 5 liter Battery 12V 40Ah FB 250 HATZ Net wWerghtgi ssni nannies 265 kg Base plate w x 1 550 x 790 mm Speed srian sten approximately 25 m min Permitted inclination 20 Centrifugal force 40 000 N Vibration frequency 80 Hz IST HATZ 1B30 Engine poWer 4 8 kW Engine KPN aaezi eee 3200 RPM Fuel tank volume 3 5 liter Fuel types eesel Diesel MK1 Oil quantity crankcase 1 1 liter Oil quantity vibration element 0 5 liter Battery 12V 40Ah 6 SWEPRODC INTERNATIONAL AB FB 225 Net weight 240 kg Base plate w x 1 550 x 790 mm Speed near approximately 25 m min Permitted inclination 20 Centrifugal force 40 000 N Vibration frequency 80 Hz Drive engine Honda GX 270 Engine power 6 0 kW Engine RPM nenne 3200 RPM Fuel tank volume 6 liter Fuel ty eT Unleaded petrol 95 98 octane Oil quantity crankcase 1 1 liter Oil quantity vibration element 0 5 liter METHOD OF OPERATION
Download Pdf Manuals
Related Search