Rexroth Hydraulic Pump A10VO Series User Manual
Contents
1. Quy AN ENT re INC PAINESVILLE OH Rexroth Hydraulic Pump A10VO Series User Manual Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 1 of 12 Concord Road Equipment Mfg Inc Functional Purpose This pump is preferred over a fixed displacement gear pump for many reasons A fixed displacement pump delivers a set volume of oil for each revolution of its drive shaft Any of this fluid flow that is not required by the hydraulic system is sent back to the oil reservoir over a restriction This oil flow times the pressure difference between the system and the reservoir is power that has been drawn from the engine and turned into heat The heat generated is a direct indication of fuel wasted and of unnecessary wear and tear on the hydraulic fluid and thus on the hydraulic system s mechanical components On the other hand this variable displacement pump monitors Senses by way of a small hydraulic line connecting it to the control valves the power requirement load on your hydraulic system and provides just enough fluid flow and pressure to meet your system s immediate need This means that the pump can be left running constantly and as your system s requirement changes the pump will simply adjust itself accordingly By doing this energy is not wasted away in the form of heat translating into fuel savings for you and less wear and tear in your hydraulic system An adjustable pressure limit is also built2. onto the pump It operates by reducing the output flow all the way to zero if necessary keeping the pressure supply to your hydraulic system from ever going too high Different maximum displacements sizes with standard mounting flanges are available to match the needs of your system Also various combinations of drive shafts splined or keyed rotation directions left hand or right hand and port locations rear or side can be chosen to facilitate your particular installation requirements Direct engine mounting as well as transmission power take off mounting can be accommodated Contact Concord Road Equipment for any application or system questions you may have Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 2 of 12 Concord Road Equipment Mfg Inc Variable displacement swash plate design axial piston pump 1 Housing 2 Control Piston 3 Input Shaft 4 Swash Plate 5 Control Valve Assembly 6 Pistons x7 Axial piston pumps model A10V0 are swash plate Vee design variable displacement pumps As illustrated Y woe ww WE by the picture under functional purpose they basically consist of a housing 1 control pistons 2 located inside cylinder barrel drive shaft 3 swash plate 4 a control valve assembly 5 and pistons 6 This piston pump smoothly and continuously varies its displacement volumetric output size by altering the angle of its swash plate As your system operates valves m
3. 350 to 400 PSI Then lock the jam nut and double check that the setting did not change 19 Run the system under load until oil reaches operating temperature Should not exceed 140 F and check all functions for leaks 20 Ensure there is still a sufficient quantity of oil in the reservoir now that all lines are full IMPORTANT NOTE Erratic operation may indicate there is still air trapped in the system By working control valves both ways the remaining air can be eliminated The system is free of air when all functions can be operated smoothly and the oil in the reservoir shows no foam on the surface Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 12 of 12 Concord Road Equipment Mfg Inc
4. Filtration required Inlet 100 mesh screen Return 10 micron absolute return filter Calculated specifications Volume output at 1000 rom nominal pressure 18 75 gallons per minute Connection portino Inlet connection port SAE 2 flange code 61 side facing max torque 45 ft lbs Outlet connection port SAE 1 flange code 61 side facing max torque 95 ft lbs max torque 30 ft lbs max torque 175 ft lbs Recommended Hose Sizes SAE 32R4 2 wire reinforced SAE 100R16 1 hose for pressures up to 2000 psi SAE 100R12 1 hose for pressures above 2000 psi Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 7 of 12 Concord Road Equipment Mfg Inc Specifications of standard variable axial piston pumps continued A10V071DFR 31R PKC91NOO Standard application PTO driven remote mount with drive shaft 149312 Part number General specifications Weight Displacement 73 Ibs 4 33 C I 71 CC per revolution Nominal pressure 4000 psi Peak pressure 5000 psi Maximum speed at max nominal pressure 2200 RPM Clockwise 1 1 4 shaft with 5 16 key SAE C 2 bolt 20 to 160 degrees Fahrenheit Rotation viewed from shaft end Input shaft Mount Operating temperature Filtration required Inlet 100 mesh screen Return 10 micron absolute return filter Calculated specifications Volume output at 1000 rom nominal pressure 18 75 gallons per minute Connection portino Inlet connecti
5. d familiarize yourself with the equipment before operating or attempting repairs or service Observe all caution and warning statements in the applicable manual and on the equipment Always use extreme caution when working with any pressurized system Always be aware of other persons and or equipment in the immediate area and the hazards involved Be prepared to immediately shut down the truck and or hydraulic system if required especially during initial startup and testing The equipment must be assembled and serviced by a trained mechanic or technician Ensure only properly trained individuals should operate the equipment Always use personal protection equipment such as eye and ear protection when indicated by the instructions or by the work environment Always operate equipment safely and within its rated capacity and performance range Hydraulic fluid in the human bloodstream can be fatal If hydraulic fluid penetrates the skin under pressure seek medical attention immediately Hydraulic oil solvents and pipe sealers may cause skin irritation and rashes Avoid lengthy exposure to these materials Wash your hands thoroughly after contact with oils solvents and other chemicals Remove clothing that is saturated with oil Do not operate equipment that is damaged or in need of maintenance Repair equipment as soon as problems are identified A component supported by an actuator will drop if the actuator or its pressure supply fai
6. gage pump PTO If applicable 11 Allow pump to run for a few moments and fully prime 12 Shut the system down re assemble any hoses or connection changed during step 9 13 Using a 3mm hexagonal key turn the standby pressure adjustment screw on the pump compensator counter clockwise as far as possible 14 Re start truck and engage pump PTO If applicable Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 11 of 12 Concord Road Equipment Mfg Inc HYDRAULIC PUMP COMMISSIONING INSTRUCTIONS Continued from previous page 15 Using a 3mm hexagonal key turn the standby pressure adjustment screw on the pump compensator clockwise as far as possible 16 Observe the gauge reading while using a 3mm hexagonal key to turn the maximum pressure adjustment screw clockwise slowly If gauge reading does not change within the first few rotations stop and start the process from step 1 again 17 Turn the maximum pressure adjustment screw clockwise slowly until the gauge reads the correct setting for maximum system pressure Then lock the jam nut and double check that the setting did not change IMPORTANT NOTE If you do not know the proper setting for maximum system pressure contact technical support at Concord Road Equipment 18 Turn the standby pressure adjustment screw counter clockwise while observing the pressure gauge The pressure reading will drop off rapidly at first then slowly Adjust the pressure to between
7. ls or if the actuator control is accidentally engaged If you are under the component when it drops you will be killed or seriously injured Always return an actuated component to its rest position or support it by other means before working under the component If an actuated component such as a dump box or plow must be raised for service it must be supported by some means other than the actuator Use body props blocks or stands to support the component Never attempt to support a loaded dump body for service The body must be empty Use tools that are suited to the task and keep your tools in good repair Use proper lifting equipment when moving or installing heavy components Keep your work area clean and safe Always clean up any spills immediately and properly dispose of the material in the designated refuse container Always shut off the vehicle engine and disconnect pump electrical power before working on the hydraulic system Concord Road Equipment Mfg Inc is not responsible or liable for injury damage or loss caused by improper installation by the end user misuse of the equipment lack of maintenance accidents or failure to follow instructions In cases where equipment application was determined by the end user Concord Road Equipment Mfg Inc is not responsible or liable for injury damage or loss caused by misapplication of this equipment Specifications parts descriptions illustrations and instructions in thi
8. need 7 Remove both caps if applicable and loosen both jam nuts on the compensator adjustment screws Use a 17mm wrench if your compensator has caps on the adjustments screws or a 13mm wrench if your compensator does not have caps over the adjustment screws 8 Using a 3mm hexagonal key turn the maximum pressure adjustment screw on the pump compensator counter clockwise as far as possible IMPORTANT NOTE New and rebuilt pumps are tested for performance at very high pressure failure to adjust this pressure to match your system requirements may cause component failure hoses to rupture and personal bodily injury 9 Since air has been introduced into the suction side of the hydraulic system either because this is the first time starting or because of replacing the pump the air must be bled off to allow pump fluid to be pumped Air will not automatically flow through because the valve has a closed center design meaning that no fluid flows unless a function is activated Bleeding air can be accomplished in a number of different ways either by directing the main pressure line back to the reservoir by loosening the main pressure line fitting until pump fully primes or by activating a free flowing spreader function like the spinner circuit IMPORTANT NOTE Loose connections or lines can be extremely dangerous as can be hydraulic fluid under pressure Take extreme caution to prevent injuries during this process 10 Start truck and en
9. on port SAE 2 flange code 61 side facing max torque 45 ft lbs Outlet connection port SAE 1 flange code 61 side facing max torque 95 ft lbs SAE 4 7 8 14UNF 2B max torque 30 ft lbs Case drain connection port SAE 10 7 16 20UNF 2B max torque 175 ft lbs Load sense connection port Recommended Hose Sizes Inlet SAE 32R4 2 wire reinforced Outlet SAE 100R16 1 hose for pressures up to 2000 psi SAE 100R12 1 hose for pressures above 2000 psi Case Drain SAE 100R16 4 hose Load Sense SAE 100R16 3 8 hose Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 8 of 12 Concord Road Equipment Mfg Inc Specifications of standard variable axial piston pumps continued Rotation viewed from shaft end Counter Clockwise Input shaft 1 1 4 shaft with 5 16 key Filtration required Inlet 100 mesh screen Return 10 micron absolute return filter Calculated specifications Volume output at 1000 rom nominal pressure 19 54 gallons per minute Connection portino Inlet connection port SAE 2 flange code 61 side facing max torque 45 ft lbs Outlet connection port SAE 1 flange code 61 side facing max torque 95 ft lbs max torque 30 ft lbs max torque 175 ft lbs Recommended Hose Sizes SAE 32R4 2 wire reinforced SAE 100R16 1 hose for pressures up to 2000 psi SAE 100R12 1 hose for pressures above 2000 psi Rexroth Hydraulic pump A10VO Series User Manual Revi
10. onitor the load pressures on the system s cylinders and or motors and control the swash plate accordingly The greater the angle of the swash plate relative to the drive shaft the further the pistons stroke in and out creating greater fluid flow There are two control valves located in a removable housing bolted to the pump The standard type of control used Is referred as flow and pressure compensator type DFR The flow and pressure compensator matches pump output flow and pressure to system demand This control will automatically regulate the pump displacement to deliver the flow required to maintain a constant pressure drop across a valve spool or other flow limiting device When there is no system demand the pump stands by at zero flow and low pressure When the system demands flow the pump delivers only the flow required by the system at a pressure required to move the load To protect the system from infinite load pressures the pressure compensator section of the control will cause the pump to automatically de stroke when the pre adjusted maximum system pressure is reached Flow and pressure compensator valve 1 Standby pressure adjustment screw 2 Maximum pressure adjustment screw 3 Gauge test port 4 Connections to pump control piston Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 3 of 12 Concord Road Equipment Mfg Inc Cautions and Warnings Always read all instructions thoroughly an
11. or pressures up to 2000 psi SAE 100R12 1 hose for pressures above 2000 psi Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 5 of 12 Concord Road Equipment Mfg Inc Specifications of standard variable axial piston pumps continued Rotation viewed from shaft end Counter Clockwise Input shaft 1 1 4 keyed shaft Mount SAE B 2 bolt Operating temperature 20 to 160 degrees Fahrenheit Filtration required Inlet 100 mesh screen Return 10 micron absolute return filter Calculated specifications Volume output at 1000 rom nominal pressure 15 8 gallons per minute Volume output at 1300 rom nominal pressure 20 6 gallons per minute Connection porting Inlet connection port SAE 2 flange code 61 side facing max torque 45 ft lbs max torque 95 ft lbs max torque 30 ft lbs max torque 175 ft lbs Recommended Hose Sizes Recommended Hose Sizes SAE 32R4 2 wire reinforced Outlet SAE 100R16 1 hose for pressures up to 2000 psi SAE 100R12 1 hose for pressures above 2000 psi SAE 100R16 hose SAE 100R16 3 8 hose Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 6 of 12 Concord Road Equipment Mfg Inc Specifications of standard variable axial piston pumps continued 103616 Rotation viewed from shaft end Counter Clockwise Input shaft 1 1 4 shaft with 5 16 key Mount SAE C 2 bolt Operating temperature 20 to 160 degrees Fahrenheit
12. s manual were accurate at the time of publication Concord Road Equipment Mfg Inc reserves the right to discontinue products and to change specifications and or designs at any time without notice and without incurring any obligation Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 4 of 12 Concord Road Equipment Mfg Inc Specifications of standard variable axial piston pumps A10VO60DFR 52R PUC61NOO Standard application PTO driven direct mount usually driven at 130 of engine speed 139175 Part number General specifications Weight 50 Ibs Displacement 3 66 C I 60 CC per revolution Nominal pressure 3600 psi 4500 psi Maximum speed at max nominal pressure 2700 RPM Peak pressure Clockwise 1 15T splined shaft SAE BB Mount SAE B 2 bolt Operating temperature 20 to 160 degrees Fahrenheit Filtration required Inlet 100 mesh screen Return 10 micron absolute return filter Calculated specifications Volume output at 1000 rom nominal pressure 15 8 gallons per minute Volume output at 1300 rom nominal pressure 20 6 gallons per minute Rotation viewed from shaft end Input shaft Connection portino Inlet connection port SAE 2 flange code 61 rear facing Outlet connection port SAE 1 flange code 61 rear facing Load sense connection port SAE 4 Case drain connection port SAE 10 Recommended Hose Sizes Recommended Hose Sizes SAE 100R16 1 hose f
13. sed 5 1 2009 Page 9 of 12 Concord Road Equipment Mfg Inc Specifications of standard variable axial piston pumps continued A10VO100DFR 31L PKC62N00 Standard application Front engine driven with drive shaft off of engine crankshaft adaptor 130924 Part number General specifications Weight Displacement 100 Ibs 6 1 C I 100 CC per revolution Nominal pressure 4000 psi Peak pressure 5000 psi Maximum speed at max nominal pressure 2000 RPM Rotation viewed from shaft end Counter Clockwise Input shaft 1 1 2 shaft with 3 8 key SAE C 2 bolt Operating temperature 20 to 160 degrees Fahrenheit Filtration required Inlet 100 mesh screen Return 10 micron absolute return filter Calculated specifications Volume output at 1000 rom nominal pressure Outlet connection port SAE 1 1 4 flange code 62 side facing Load sense connection port SAE 4 SAE 12 Inlet connection port Case drain connection port Recommended Hose Sizes Inlet Minimum SAE 32R4 2 wire reinforced Outlet Minimum SAE 100R16 1 hose for pressures up to 2000 psi SAE 100R12 1 hose for pressures above 2000 psi Case Drain SAE 100R16 34 hose Load Sense SAE 100R16 3 8 hose Rexroth Hydraulic pump A10VO Series User Manual Revised 5 1 2009 Page 10 of 12 Concord Road Equipment Mfg Inc HYDRAULIC PUMP COMMISSIONING INSTRUCTIONS 1 Ensure all components are flushed clean and free of gri
14. t and dirt 2 Fill the hydraulic oil reservoir and pump through a filter to avoid adding contamination to the hydraulic system IMPORTANT NOTE Fill the pump case to the highest case drain or vent port Use clean filtered fluid A pump of this construction relies on the oil it is pumping to provide lubrication for its moving parts Never run an A10VO series pump dry it will be instantly damaged 3 Ensure all hoses fittings and couplers are tightened correctly 4 Ifthe system is equipped with a cartridge style shut off in the main pressure line from the hydraulic pump to the valve remove the shutdown coil and cartridge and install a SAE o ring seal plug in its place 5 Ifthe system is equipped with shutoff valves in the suction pressure or return circuits check and be sure that all are open for flow 6 Install a pressure gauge in the pressure line from the pump this can be easily accomplished by installing a gauge into the test port in the bottom of the compensator See compensator figure for test port location Some valves may be equipped with a gauge port for this purpose contact Concord Road Equipment for details about the equipment you are working on A IMPORTANT NOTE Failure to use proper adaptors or properly rated test equipment can cause component failure or personal bodily injury Contact Concord Road Equipment for the proper adaptor to install a gauge in the compensator or any other hydraulic test equipment you might
Download Pdf Manuals
Related Search