Explorer 575 Wash - Enlightenment Entertainment Technology
Contents
1. Fig 5 1 0 8 0 6 0 4 0 2 0 0 2 0 4 0 6 0 1m Diameter Set Up and Operation Follow the directions below as they pertain to your preferred operation mode Before plugging the unit in always make sure that the power supply matches the product specification voltage Do not attempt to operate a 120V specification product on 230V power or vice versa One Explorer 1 Fasten the moving head onto firm trussing Use a 30 kg rated or stronger C clamp fastened onto the Explorer Leave at least 1 meter on all sides for air circulation 2 Plug one end of the electric mains power cord into the IEC socket on the unit Then plug the other end of the cord into a proper electric power supply socket 3 Use the Mode button to set the fixture to RUN and choose PRG1 The Explorer will now play its built in program Multiple Explorers 1 Fasten the effect light onto firm trussing Use a 30 kg rated or stronger C clamp fastened onto the Explorer Leave at least 1 meter on all sides for air circulation 2 Use a 3 p XLR cable to connect the Explorers and other devices Occupation of the XLR connection DMX OUTPUT DM X input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal The transformation of the controller line of 3 pins and 5 pins plug and socket 5 Pins canon socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal2. Pin 4 N C Pin 5 N C 3 Pins canon plug Pin 1 GND screen Pin 2 Signal Pin 3 Signal 5 Pins canon plug Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 N C 3 Pins canon socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal 3 Link the units as shown in figure 6 Connect a DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this process to link the second third and fourth units 4 Supply electric power Plug electric mains power cords into each unit s IEC socket then plug the other end of the mains power cord into proper electric power supply sockets starting with the first unit Do not supply power before the whole system is set up and connected properly 10 DMX Set up Fig 6 Note Link all cables before connecting electric power DMX Protocol Channel 1 Horizontal movement Pan Push the slider up in order to move head horizontally PAN Gradual head adjustment from one end of the slider to the other 0 255 128 center The head can be turned by 540 and stopped at any position you wish Channel 2 Vertical movement Tilt Push the slider up in order to move head vertically TILT Gradual head adjustment from one end of the slider to the other 0 255 128 center The head can be turned by 280 and stopped at any position you wish Channel 3
3. Explorer 575 Wash ORDERCODE 40192 SHOWELECTRONICES FOR PROFESSIONALS Congratulations You have bought a great innovative product from Showtec The Showtec Explorer 575 brings excitement to any venue Whether you want simple plug amp play action or a sophisticated DMX show this product provides the effect you need You can rely on Showtec for more excellent lighting products We design and manufacture professional light equipment for the entertainment industry New products are being launched regularly We work hard to keep you our customer satisfied For more information iwant showtec info You can get some of the best quality best priced products on the market from Showtec So next time turn to Showtec for more great lighting equipment Always get the best with Showtec Thank you Showtec Showtec Explorer 575 Product Guide Ne E E Sr a 140 ARBERREERSDERDPRREFRFEPEREPFREFEFFOALPRPERFERTHELENTERNEREEBEUHERFEETEERERIFETEERERREUEEREFETTERPRETEDELER Operating Determinations Description Features and Overview Backside INSTALL de en ee ee eee ee Installing the Lamp Lamp Adjustment PN Set Up 5 49 015 2 DMX Protocol Control Panel Control Mode DMX addressing Stand alone mode Functions control pa
4. Pan fine 16 bit Channel 4 Tilt fine 16 bit Channel 5 Scan Speed Adjustment 0 255 Gradual adjustment Scan Speed from fast to slow Channel 6 Keep 0 255 Keep this Color setting Channel 7 Color wheel 25 49 RED 11 Channel 8 CYAN 0 255 Gradual adjustment Cyan from 0 100 Channel 9 MAGENTA 0 255 Gradual adjustment Magenta from 0 100 Channel 10 YELLOW 0 255 Gradual adjustment Yellow from 0 100 Channel 11 CMY color change speed 0 255 Gradual adjustment color change speed from fast to slow Channel 12 CMY Color Effect wheel Channel 13 Effect wheel Channel 14 Zoom 0 255 Gradual adjustment Zoom from 7 to 28 Channel 15 Shutter strobe 0 9 Shutter 10 40 41 250 Strobe effect from slow to fast 251 255 Channel 16 Dimmer intensity 0 255 Gradual adjustment dimmer intensity from 0 100 Control Panel When the indicator light is on means the Explorer is working Fig 7 A LED D ENTER Button B Display E Up Button C MODE Button F Down Button Control Mode The fixtures are individually addressed Hit ton a data link and connected to the controller The fixtures respond to the DMX signal from the controller When you select the DMX address and save it the controller will display the saved DMX address the next time DMX Addressing The control panel on the front side of the base allows you to assign the DMX fixture ad
5. Do not attempt the installation yourself Always let the installation be carried out by an authorized dealer Procedure e If the projector is lowered from the ceiling or high joists professional trussing systems have to be used e Use a clamp to mount the projector with the mounting bracket to the trussing system The projector must never be fixed swinging freely in the room The installation must always be secured with a safety attachment e g an appropriate safety net safety cable When rigging derigging or servicing the projector always make sure that the area below the installation place is blocked and staying in the area is forbidden ITXXAX a CHE The Explorer can be placed on a flat stage floor or mounted to any kind of truss by a clamp Mounting a clamp to the underside of the Explorer moving head T lt Clamp Safety cable Eye bolt Mounting plate 7 ft rt 1 2 3 A Improper installation can cause serious damage to people and property Connection with the mains Connect the device to the mains with the power plug Always pay attention that the right color cable is connected to the right place Cable Pin internationa BROWN FASE BLUE YELLOW GREEN EARTH Make sure that the device is always connected properly to the earth 5 Description of the device Features The Showtec Explorer 575 Wash is a movi
6. Does the controller operate properly with other DMX products If not take the controller in for repair If so take the DMX cable and the light effect to a qualified technician See next page for more problem solving 17 Probable cause s No power to the fixture Check that power is switched on and One or more cables are plugged in fixtures are completely dead Primary fuse blown Replace fuse Fixtures reset The controller is not connected Connect controller correctly but all 3 pin XLR Out of the controller Install a phase reversing cable respond does not match XLR Out of the between the controller and the first erratically or not first fixture on the link i e signal is fixture on the link at all to the reversed controller Check data quality If much lower than 100 percent the problem may be a bad data link connection poor Poor data quality quality or broken cables missing termination plug or a defective fixture disturbing the link Inspect connections and cables Bad data link connection Correct poor connections Repair or replace damaged cables Data link not terminated with 120 Insert termination plug in output jack Fixtures reset Ohm termination plug of the last fixture on the link correctly but Incorrect addressing of the Check address setting some respond fixtures erratically or not Bypass one fixture at a time until at all to the normal operation is rega
7. fixture s light output will be significantly reduced Disconnect the mains power supply and then wipe the cover with a damp cloth Do not immerse in liquid Wipe lens clean with glass cleaner and a soft cloth Do not use alcohol or solvents The front PC lens will require weekly cleaning as smoke fluid tends to build up residues reducing the light output very quickly The cooling fans dichroic colour filters the gobo wheels the gobos and the internal lenses should be cleaned monthly with a soft brush To ensure proper functioning of the gobowheel we recommend lubricating the wheel every 6 months The quantity of oil must not be excessive Please clean internal components once a year with a light brush and vacuum cleaner Keep connections clean Disconnect electric power and then wipe the DMX and audio connections with a damp cloth Make sure connections are thoroughly dry before linking equipment or supplying electric power Changing the Lamp 1 Disconnect mains power supply Loosen the 3 screws X Y Z on the backside of the lamp cover See Backpanel Fig 4 2 Gently pull out the lamp board 3 Follow directions for installing a new lamp page 8 Replacing a Fuse Power surges short circuit or inappropriate electrical power supply may cause a fuse to burn out If the fuse burns out the product will not function whatsoever If this happens follow the directions below to do so 1 Unplug the unit from electric power source
8. functions Colour wheel The Explorer contains a colour wheel with 4 colored gobos 2 color Temp filters 1 UV filter and one white Shutter Dimmer Strobe The dimming 0 100 is provided by a simple mechanical shutter unit This unit may also be used for strobe effect 1 10 flashes per second Stand alone Mode The fixture can execute 1 pre set program Use the Mode button to set the fixture to RUN and choose PRG1 The Explorer will now play its built in program For synchronous operation of multiple fixtures the fixtures must all be connected on a data link Note Disconnect the fixtures from the DMX controller before operating otherwise data collisions can occur and the fixtures will not work properly It s necessary to insert the XLR termination plug with 120 Ohm into the input of the first fixture and into the output of the last fixture in the data link in order to ensure proper transmission on the data link Addressing With this menu you can set the DMX address or address a fixture as a master slave OnI DMX addressing 1 Press until the display shows 2 Press 4 to confirm the display will show HS S with actually stored address And press A and Y to select the required address ALL Ho press 4 to confirm A 3 Press the chosen address is shown the display 14 Function Table Mode Function Condition Pan movement in positive or negative directio
9. 2 Insert a screwdriver into the slot in the fuse cover Turn the screwdriver to the left at the same time gently push a bit Turn and Push The fuse will come out 3 Remove the used fuse If brown or unclear it is burned out 4 Insert the replacement fuse into the holder where the old fuse was Reinsert the fuse cover Be sure to use a fuse of the same type and specification See the product specification label for details 16 Troubleshooting No Light No Movement All Products This troubleshooting guide is meant to help solve simple problems If a problem occurs carry out the steps below in sequence until a solution is found Once the unit operates properly do not carry out following steps If the light effect does not operate properly refer servicing to a technician Response Suspect three potential problem areas the power supply the lamp the fuse 1 Power supply Check that the unit is plugged into an appropriate power supply 2 The lamp Replace the old lamp with a new one with the same specifications See page 8 for replacing lamps 3 The fuse Replace the fuse See page 16 for replacing the fuse No Response to DMX Response Suspect the DMX cable or connectors a controller malfunction a light effect DMX card malfunction 1 Check the DMX cable Unplug the unit change the DMX cable then reconnect to electrical power Try your DMX control again 2 Determine whether the controller or light effect is at fault
10. 3 pin XLR male Signal output 3 pin XLR female Lamp Allowed lamp models Philips MSR 575 1000 hr 6000K ordercode 80915 Osram HSR 575 2 750 hr ordercode 809150 Philips MSR 575 1000 hr 7200K ordercode 80923 Control Automatic and DMX remote ON OFF Electro mechanical effects Colors 7 colors plus white All lenses are anti reflection coated High luminous efficiency parabolic system Strobe effect with variable speed 1 flash 10 flashes sec DMX control via standard DMX controller Pan 0 530 Tilt 0 280 Automatic Pan Tilt position correction Wheel control auto electronic reset Beam Angles 7 28 Max ambient temperature t 40 C Max housing temperature tg 80 C Fresnel lens 200mm diameter Minimum distance Minimum distance from flammable surfaces 0 5m Minimum distance to lighted object 2m Versions for other lamps may be produced Please check the specification label on your product Design and product specifications are subject to change without prior notice 19 2006 Showtec
11. dress which is the first channel from which the Explorer will respond to the controller Please note when you use the controller the unit has 16 channels When using multiple Explorers make sure you set the DMX addresses right Therefore the DMX address of the first Explorer should be 1 A001 the DMX address of the second Explorer should be 1 16 17 A017 the DMX address of the third Explorer should be 17 16 33 A033 etc Please be sure that you don t have any overlapping channels in order to control each Explorer correctly lf two or more Explorers are addressed similarly they will work similarly For address settings please refer to the instructions under Addressing menu Controlling After having addressed all Explorer fixtures you may now start operating these via your lighting controller Note After switching on the Explorer will automatically detect whether DMX 512 data is received or not If there is data received at the DMX input the LED on the control panel will not flash The problem may be The XLR cable from the controller is not connected with the input of the Explorer The controller is switched off or defective the cable or connector is detective or the signal wires are swapped in the input connector Note It s necessary to insert a XLR termination plug with 120 Ohm in the last fixture in order to ensure proper transmission on the DMX data link 13 Remotely controllable
12. each of children Never leave the unit running unattended For replacement use lamps and fuses of same type and rating only Allow time to cool down before replacing lamp This device falls under protection class Therefore it is essential to connect the yellow green conductor to earth During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective Repairs servicing and electric connection must be carried out by a qualified technician WARRANTY Till one year after date of purchase CAUTION EYEDAMAGES IN Avoid looking directly into the light source meant especially for epileptics OPERATING DETERMINATIONS This device is not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects The minimum distance between light output and the illuminated surface must be more than 2 meters The maximum ambient temperature must never be exceeded If this device is operated in any other way than the one described in this manual the product may suffer damages and the warranty becomes void Any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash etc You endanger your own safety and the safety of others 3 Rigging Please follow the European and national guidelines concerning rigging trussing and all other safety issues
13. flammable liquids or gases Always replace the lamp when it is damaged or deformed due to the heat Always keep case closed while operating Always allow free air space of at least 50 cm around the unit for ventilation Always disconnect power from the mains when device is not used before cleaning or when replacing lamp Only handle the power cord by the plug Never pull out the plug by tugging the power cord Make sure that the device is not exposed to extreme heat moisture or dust Make sure that the available voltage is not higher than stated on the rear panel Make sure that the power cord is never crimped or damaged Check the device and the power cord from time to time If the lens is obviously damaged it has to be replaced So that its functions are not impaired due to cracks or deep scratches If device is dropped or struck disconnect mains power supply immediately Have a qualified engineer inspect for safety before operating If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature If your Showtec device fails to work properly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Showtec dealer for service For adult use only Movinghead must be installed out of the r
14. horized modification to the device Never let the power cord come into contact with other cables Handle power cord and all connections with the mains with particular caution Never remove warning or informative labels from the unit Never use anything to cover the ground contact Never run the device without lamp Never ignite the lamp if the objective lens or any housing cover is open as discharge lamps may expose and emit a high ultraviolet radiation which may cause burns e Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles Never look directly into the light source Never leave any cables lying around Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened Do not insert objects into air vents Do not connect this device to a dimmerpack Do not switch the device on and off in short intervals as this would reduce lamp s life Do not touch the device s housing bare handed during its operation housing becomes very hot Do not shake the device Avoid brute force when installing or operating the device Only use device indoor avoid contact with water or other liquids Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened Only operate the device after having familiarized with its functions Avoid flames and do not put close to
15. ined unplug One of the fixtures is defective both connectors and connect them and disturbs data transmission on directly together the link Have the defective fixture serviced by a qualified technician Install a phase reversing cable 3 pin XLR Out on the fixtures does between the fixtures or swap pin 2 not match pins 2 and 3 reversed and 3 in the fixture that behaves erratically Shutter closes The color wheel gobo wheel or a Contact a technician for servicing if suddenly gobo has lost its index position the problem persists and the fixture is resetting the effect The power supply settings do not Disconnect fixture Check settings No light match local AC voltage and page 8 and correct if necessary frequency Lamp missing or blown Disconnect fixture and replace lamp Allow fixture to cool Lamp cuts out Fixture is too hot Clean fan intermittently Make sure air vents at control panel and front lens are not blocked Turn up the air conditioning The power supply settings do not Disconnect fixture Check settings match local AC voltage and page 8 and correct if necessary frequency 18 Product Specification Model Showtec Explorer 575 Voltage 240V 50Hz CE Power 850W Fuse 10 250V Weight 35 5 kg Operation and Programming Signal pin OUT pin 1 earth pin 2 pin 3 Set Up and Addressing LED control panel DMX Channels 16 Signal input
16. mp and the lens was already set during the installation with screw A only the Hot Spot the brightest part of the ray of light must be centered Turn in addition screw and If the Hot Spot appears too bright you can weaken its intensity by moving the lamp closer to the reflector Turn in addition screw A until the light is evenly distributed If the light at the outside edge of the ray of light appears brighter as in the center the lamp is too close to the reflector In this case move the lamp away from the reflector until the light is evenly distributed and the ray of light appears bright enough 7 Beam Angle min zoom 2123 En 133 Foot candles 22850 1430 LUX 0 2 9 5 7 5 10 12 5 15 17 5 20m Distance 0 62 1 22 1 83 2 45 Diameter 577 64 Jen HHA HHR 36 Foot candles 390 LUX 5 7 5 10 12 5 15 17 5 20m Distance 2 49 4 99 7 47 9 97m Diameter Distance 5m nn N 7 radiation angle UN 1 4 4 DEN RENTE SRE 1 Foot candies LH HHH 1 gt h on 12000 ai tii an Rees 128 radiation u 1 6000 au 557 2 1 DD DE EN TR 134 Rw BBE EE ESS
17. n YES negative direction _ Vertical movement in positive LE or negative direction YES negative direction cr Address code set Reset YES reset Rainbow colorwheel change color linear or stepping YES linear DMX 512 mode E Working mode PB Automatic Mm Hr Lamp On UFF Lamp Off Lamp switch 40192 Explorer WASH 575 with Co Fixture settings 8 Colour Effect Beam out 15 Maintenance The operator has to make sure that safety relating and machine technical installations are to be inspected by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are to be inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded 2 There may not be any deformations on housings fixations and installation spots 3 Mechanically moving parts like axles eyes and others may not show any traces of wearing 4 The electric power supply cables must not show any damages or material fatigue The Showtec Explorer 575 requires almost no maintenance However you should keep the unit clean Otherwise the
18. nel Channel settings Maintenance me CaN er a a see ern ee ee ae eee eee ne eee RER INGE ee eee E E Troubleshooting No Light No Movement All Products POUCES D CORS ee en a ce ee NO RESPONSE NE ee nee ee WARNING CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP SAFETY INSTRUCTIONS Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires Before your initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device To maintain perfect condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Please consider that damages caused by manual modifications to the device are not subject to warranty This device contains no user serviceable parts Refer servicing to qualified technicians only IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unaut
19. ng head with high output and great effects 1 Color wheel with 4 colored gobos 2 color Temp filters 1 UV filter and open 1 CMY color Effect wheel e DMX control via standard DMX controller 16 DMX control channels required e Strobe effect with adjustable speed 1 10 flashes sec e Motorized zoom 7 28 Pan 0 530 e Tilt 0 280 e Lamp MSR 575 e Fuse T10A 250V Overview Fig 1 1 Lens 2 Display 3 Menu Select buttons Backside LIGHTING CONTROL PROTOCOL DR SERIALDATALINK OUT IM 4 9 4 DMX signal connector OUT 5 DMX signal connector IN 6 ON OFF 7 Fuse 7 Fig 2 Installation Installing the Lamp The Showtec Explorer 575 uses the MSR 575 ordercode 80915 809150 80923 bulb as manufactured by all popular manufacturers Use only the appropriate lamp for your unit Note that product versions that use other lamps may be offered in the future Check your product specification label for information Always disconnect from electric mains power supply before changing lamps The lamp has to be replaced when it is damaged or deformed due to the heat Do not install lamps with a higher wattage Lamps with a higher wattage generate temperatures the device was not designed for Damages caused by non observance are not subject to warranty Procedure 1 Loosen the 3 screws X Y Z on the backside of the lamp cover See Backpanel Fig 4 2 Gen
20. tly pull out the lamp board 3 Read lamp instructions Do not touch the lamp bulb glass See Figure 3 Oil on hands shortens the lamp life If you touch the bulb glass wipe off the glass with a clean lint free towel and rubbing alcohol 4 Insert the lamp pins into the small holes in the lamp socket You can adjust the distance between the lamp and the lens screw A on the back 5 Put the backpanel back and fasten the screws snugly gt Lamp board Lamp holder 1 2 3 4 Fig 3 Remove the screws and Z for re lamping Backside Lamp Board WARNING Disconnect the fixture from AC power before r amp lamping Lamp is hot Risk of fire Protect hands eyes Wait at least 15min before opening the covers and removing lamp from the fixtyre z Minimum distance from flammabl material d 0 5m Exterior surface T 80 Adjust lamp positiok Fig 4 3 adjustment screws A B C Lamp Adjustment You can adjust the lamp s position by turning the screws A B C The lamp position is set in the factory As the lamps which can be used differ from manufacturer to manufacturer it can be necessary to readjust the position The lamp must be readjusted e g if the light does not seem to be evenly distributed within the ray of light Ignite the lamp and focus the ray of light on an even surface wall As the optimal distance between the la
Download Pdf Manuals
Related Search