COBPAR100W
Contents
1. www destilan deutschland de2. INYO Bedienungsanleitung User manual COBPAR 100W www destilan deutschland de BCE Table of contents INTRODUCTION ee en nee 2 SAFETY INSTRUCTIONS wise u nee 2 OPERATING 3 DESCRIPTION OF THE DEVICE a nennt 4 INSTALLATION no enaa a ee OPERATION ua Stand alone Master slave Opera DMX controlled operatiOM ann 6 i aaa a EEE 6 Control Doard cre rrr 6 Protocol oraes aee EAEE ces AN SEN aa 7 TECHNICAL er 7 esse a sure ner 2 7 SSS 26 8 SS SS ee SSS oe eee ele eee CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initially start up Every person involved with installation operation and maintenance of this fixture has to be qualified follow the instruction of this manual consider this manual to be part of the total product Keep this manual for the entire service life of the product pas
3. an change the selection by pressing Up or Down Confirm every selection by pressing the Enter button You can leave every mode by pressing the Mode Esc button The functions provided are described in the following setting MENU MAP The device has two operation modes It can be operated in Stand Alone or in DMX controlled When in Master Slave Synchronization Mode only one 4 in 1 LED WASH in a series chain can be set as the master Menu STAT W 000 Adjust white from 0 255 DMX Adjust DMX value from 001 to 512 TEMP CURR show current fixture temperature Note output default setting address code is 001 pan is positive circumrotate tilt is positive circumrotate LED positively reveal Master slave mode auto running sound control This mode will allow you to link up 32 units together without a controller Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of t DMX protocol Channel Function Dimmer 0 100 dimmer Dimmer Optional 0 No function 4 1 250 Dimmer delay upon volume 251 255 Normally Dimmer Strobe 3 0 10 No strobe 11 255 Strobe with increasing TECHNICIAL SPECIFICATIONS Model COBPAR100W Voltage 110V 250V 50 60Hz Power consumption 120w LED 100w white COB led Gross Weight 2 9Kgs Dimensions 37 H x25 W x25 L mm 2809 266 05
4. hannel DMX 512 in optional gt Variable electronic strobe gt Variable electronic dimmer 0 100 and 4 type in optional gt Digital LED display gt Reset to factory settings option gt Color temperature setting gt Build in program with speed adjustment gt Fan cooled INSTALLATION Rigging The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation IMPORTANTIOVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including calculating working load limits installation material being used and periodic safety inspection of all installation material and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The projector had to be installed out of the reach of people DANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of min 0 5m DMX 512 connection connection between fixture The wires must not come into contact with each other otherwise the fixture will not work at all or properly Please note the starting address depends upon which controller is being used Only use a DMX cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture to another Occupa
5. leading to mortal electrical shock If the power plug or the power switch is not accessible the device must be the disconnected via the mains If the power plug or the device is dusty the device must be take out of operation disconnected and then be cleaned with a dry cloth Dust can reduce the insulation which may lead to mortal electrical shock More severe dirt in and at the device should only be removed by a specialist There must never enter any liquid into power outlets extension cords or any holes in the housing of the device If you suppose that also a minimal amount of liquid may have exerted the device it must immediately be disconnected This is also valid if the device was exposed to high humidity Also if the device is still running the device must be checking by a specialist if the liquid has reduced any insulation Reduced insulation can cause mortal electrical shock There must never be any objects entering into the device This is especially valid for metal parts If any metal parts like staples or coarse metal chips enter into the device the device must be taken out of operation and disconnected immediately Malfunction or short circuits caused by metal parts my cause mortal injuries Never look directly into the light source as sensitive persons may suffer an epileptic shock especially meant for epileptics Keep away children and amateurs Never leave this device running unattended DESCRIPTION OF THE DEVICE Features gt c
6. n the device Wrong voltages or power outlets can lead to the destruction of the device and mortal electrical shock Always plug in the power plug last The power plug must always be inserted without force Make sure that the plug is tightly connected with the outlet Never let the power cord come into contact with other cables Handle the power cord and all 2 connections with the mains with particular caution Never touch them with wet hands as this could lead to mortal electrical shock Never modify bend strain mechanically put pressure on pull or heat up the power cord Never operate next to sources of heat or cold Disregard can lead to power cord damages fire or mortal electrical shock The cable insert or the female part in the device must never be strained There must always be sufficient cable to the device Otherwise the cable may be damaged which may lead to mortal electrical shock Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time If extension cords are used make sure that the core diameter is sufficient for the required power consumption of the device All warnings concerning the power cords are also valid for possible extension cords Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord Otherwise the cable or plug can be damaged
7. s this manual to every future owner or use of the product INTRODUCTION Thank you for choosing our fixture if you follow up the instruction given in this manual we be sure that you will enjoy this product for a long period of time SAFETY INSTRUCTION CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires ob ses This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instruction and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject o warranty the dealer will not accept liability for any resulting defects of problem If the device had been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it had reached room temperature Please make sure that there are no obvious transport damages should you notice any damages on the AC connection cable or on the casing do not take the device into operation and immediately consult your local dealer The device falls under protection class The power plug must only be plugged into a protection class outlet The voltage and frequency must exactly be the same as stated o
8. tion of the XLR connection DMX output DMX input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal Connection with the mains The occupation of the connection cables is as follows Cable Pin __ International er fem The earth has to be connected The device must only be connected with an electric installation carried out in compliance with IEC standards OPERATION After you connected the effect to the mains The fixture starts running Stand Alone operation In the stand alone mode the fixture can be use without controller Master slave operation The master slave operation enables that several devices can be synchronized and controlled by one 4 master device DMX controlled operation You can control the projectors individually via your DMX controller Addressing The control board allows you to assign the DMX starting address Note it s necessary to insert the XLR termination plug with 120 in the last device in the link in order to ensure proper transmission on the DMX data link CONTROL BOARD The control board offer several features you can simple set the starting address run the pre programmed program or make a reset O MODE ESC UP DOWN ENTER he main menu is accessed by pressing the Mode Esc button Browse through the submenu by pressing Up or Down Press the Enter button in order to select the desired menu You c
Download Pdf Manuals
Related Search
COBPAR100W