USER MANUAL
Contents
1. of the UPS depend partially on the care taken by user Please observe the following precautions Do not disassemble the UPS Do not attempt to power the UPS from any receptacle except a 2 pole 3 wire grounding receptacle Do not place the UPS near water or in environment of excessive humidity Do not allow liquid or any foreign object to get inside the UPS Do not plug appliances such as hair dryers into the UPS receptacles Do not place the UPS under direct sunshine or close to heat emitting source The power socket should be installed near the equipment and be easily accessible To isolate from AC input disconnect the plug in the power cord The printer may best be connected directly to wall receptacle instead of UPS laser printer can t be connected to the UPS e The battery will discharge naturally If it is charged periodically its life time will be prolonged It will damage if long term no use which won t be covered in our warranty 1 2 System Description The UPS equipped with Boost up and Buck down features Accepts wide range input windows without using batteries It is your best choice for LAN and PC Built in RJ45 jacks protect your modem fax line thoroughly To enable user to start on the UPS without Utility Power It is also equipped with cold start function 2 INSTALLATION AND OPERATION 2 1 Unpacking and Inspection Examine the packing carton for damage Notify the carrier immediately if any damage occurs Retain2. the packing for future use 2 2 Installation Connect the power cord to a verified grounded 3 wire receptacle e Charge the batteries for ten 10 hours before use The UPS will recharge the batteries automatically whenever its power cord is plugged into a wall outlet You may use the UPS immediately without recharging but the backup time may be less than the rating Connect the power cord of your computer equipment to the Backup Outlets of the UPS Switch on the computer equipment Caution Do not plug laser printers into the Backup Outlets because they may draw too much power e Switch on the UPS by pressing the Main Switch The Mains LED will light on The UPS is now considered to be working proper If overload condition occurs the alarm will beep continuously it means you have connected too many devices Please proceed to unplug the least critical equipment from Backup Outlets e To test backup function you may disconnect the power cord of the UPS The Mains LED of the UPS will Light intermittently and the alarm will beep every 4 seconds 2 3 Storage Instruction For extended storage in moderate climates the batteries should be charged for 12 hours every 3 months by plugging the power cord into the wall receptacle Repeat it every 2 months in high temperature locations 3 OVERVIEW 1 Sockets protected from grid failures and power surges 2 Overload fault indicator 3 Battery mode indicato
3. Technical data Model 650 750 900 Technology Line Interactive Power VA 650 750 900 Power W 390 450 540 Input nominal voltage V 230 Input voltage range 25 Input nominal frequency Hz 50 60 Input frequency range 5 Surge protection J 175 EMI RMI filter MHz 30 1000 Output nominal voltage V 230 Output voltage range 10 Output frequency Hz 50 60 Transfer time ms 6 Battery Sealed lead acid without maintenance battery capacity Ah 7 7 9 Recharge time h 6 8 90 Backup time min 5 15 depend on loas Humidity 0 90 Temperature C 0 40 Dimensions D x W x H mm 260 x 170 x 80 Net Weight kg 6 6 5 ORVALDI Power Protection Sp z 0 0 Office Aleje Jerozolimskie 123 02 017 Warszawa Poland Internet www orvaldi com pl e mail orvaldi orvaldi com pl m 8 orvaldi Power Protection USER MANUAL ORVALDI 6350 750 900 SP ORVALDI Power Protection Sp z 0 0 Centre Logistics and Service 33D Wroctawska Str 55 090 Dlugoleka Poland www orvaldi com pl service orvaldi com 1 INTRODUCTION 1 1 Safety Instruction Caution e The UPS contains voltages which are potentially hazardous All repairs should be performed by qualified service personnel The UPS has its own internal energy source battery The output receptacles may be live even when the UPS is not connected to an AC supply For safe and continuous operation
4. me type and connect properly red to red 5 Put in the battery close the cover and screw in the screws
5. r 4 Normal mode 5 On off button press at least 4 seconds 6 Sockets protected from power surges 7 Circuit breaker protection from overloads 8 RJ11 RJ45 connectors protects a tel network line from power surges available in 750 900 SP 9 USB connector computer communication available in 750 900 SP 10 Power cord input 4 TROUBLESHOOTING The Troubleshooting chart covers most of the difficulties that you may encounter under normal working condition Should the UPS fails to operate properly please proceed the followings before calling for service Is the UPS plugged into an incorrect wall receptacle If AC input voltage out of windows When calling for service please offer_the following information Model No and Serial No Date of problem occur o Full description of the problem occur Including condition happened environment installed devices connected to the UPS etc 5 VISUAL amp AUDIBLE ALARMS Normal mode without any load connected diode no 4 is slowly flashing Normal mode with load connected diode no 4 is quickly flashing Battery mode 1 beep 3 sec Diode no 3 is slowly flashing Low battery 1 beep sec Diode no 3 is quickly flashing Exhausted battery Continuously beep 5 sec 6 BATTERY REPLACEMENT 1 Unplug the power cord from the socket 2 Unscrew two screws from battery cover slip out the cover 3 Take off and unplug the battery 4 Replace to battery this sa
Download Pdf Manuals
Related Search