Serial to TCP/IP Converter
Contents
1. eeeeeseseeees Hyper Terminal for TCP IP WinSock Hyper Terminal for COM Port eere Data Transmission eue seu Sagres Appendix FAQ cese Appendix B Pin Outs and Cable Wiring DC In Jack save sess B 2 RJ 45 Pin Assignment B 3 RS 232 Pin Assignment evonovnvnnnnnnnnvnnnnnnnnnnnnnnnener 4 RS 232 Wiring Diagram 5 RS 422 Pin Assignment eee eene B 6 RS 422 Wiring Diagram ee eeeeeee eene B 7 RS 485 Wiring Diagram eene 1 Introduction We provide new ways of connecting legacy serial devices to Local Area Network LAN or Wide Area Network WAN TCP IP converters are designed to operate serial ports over 100M bps Ethernet networks The data is transmitted via TCP IP protocol Therefore control is available via Ethernet Intranet and Internet EX 9132C 2 converter is packaged in a PVC material case well suited for industrial environments It provides two serial ports one is RS 232 and another is RS 232 422 485 Auto Detect All serial ports operate in common industrial configuration EX 9132C 2 converter is a low cost high performance design By carefully selecting high quality with competitive prices components in the world the products made network connectivity possible with affordable cost for virtual2. TCP Server 0 8 bd msec Server w 0 In 5 v 2 in 10 4 n 1 8 Figure 3 10 24 Parameter Setting Page Field Description IP Address The IP address of converter device 4 digits separated by Don t let it conflict with the other devices on the network If DHCP client mode is enabled and there s a DHCP server on the network this field will be assigned by DHCP server automatically Subnet mask Subnet mask of the converter device has connected to 255 255 255 0 is usually used for small network 255 255 0 0 for larger network 4 digits separated by If your IP address is provided by an ISP or the internal network administrator please inquire of them that information and type it correctly If DHCP client mode is enabled and there s a DHCP server on the network this field will be assigned by DHCP server automatically Gateway address Gateway or Router IP address Gateway is a device which connects local network to external network Ifyou need to communicate with other networks or your device owns a real IP address on the internet please inquire of them that information and type it correctly If there s no gateway on the network just leave it as 0 0 0 0 If DHCP client
3. Second use any point tip to push this button and hold it to turn on the power at the same time for 5 second All the parameters will be reset to the factory default LED Indicators PWR Red It is a power indicator When the power is on the LED will be on Tx Green Data transmitting indicator When data are sending to the network the LED will blink Rx Red Data received indicator When data are receiving by the network the LED will blink SYS Green It is a device statues indicator When EX 9132C 2 is operated in normal statues the LED will blink once per second Wiring Architecture RS 232 Wiring Architecture RS 232 Wiring 9132 2 Serial Device ii LAN Cable pe RN d fey X v d GND GND RS 232 RTS CTS Wiring EX 9132C 2 Serial Device TX RX J LAN Cable RX TX GND GND CTS RTS RIS S GIS RS 232 RTS CTS DTR DSR Wiring EX 9132C 2 Serial Device TX RX J hue LAN Cable TX GND GND CTS RTS RTS CTS DSR DTR DSR RS 422 RS 485 Wiring Architecture RS 422 Wiring EX 9132C 2 Serial Device h LAN Cable T Re dh free nr gt R T T RS 485 Wiring I 4 LAN Cable BR R R Te TE E 14 When you finish the
4. connecting the extension serial device Local Port Socket Mode Remote IP amp Port This converter devoice provides one socket connections port Port number socket port assigned for the serial port It s 16 bit numbers ranging from 1 to 65535 Because the numbers below 1000 are used for specific purposes e g 80 is for HTTP protocol we suggest you use the numbers larger than 1000 Generally the port number 4660 is used for the serial communication However you should specify different port number for each serial port Socket type TCP Server TCP protocol passive open to be connected from the TCP clients Client TCP protocol active open connect to TCP server UDP Client UDP protocol connectionless Remote IP address 26 The server IP address and socket port would be connected in TCP Server TCP Client and UDP Client mode for certain serial port Remote socket port The server socket port would be connected in TCP Client and UDP Client mode for certain serial port Interface of serial I O RS232 TxD RxD for data stream no flow control RS232 RTS CTS TxD RxD for data stream RTS CTS for flow control Baudrate Baud Rate 300 115 2K bps Parity Data bits Stop bit Parity None Even Odd Space Mark Data Bits 5 6 7 8 Stop Bit I or 2 Force off line time It is for setting the off line time period of device will be
5. Figure 3 3 EXBrowser Modify IP Modify IP gt Dialog Frame To click the device on the existing devices list in the EXBrowser table and then the function bar will be enable To press second icon of Modify IP on function bar and dialog frame table will be shown see Figure 3 4 18 EXBrowser V1 20 pum IP Address Subnet Mask MAC i EX 9132C 2 192 168 0 100 255 255 255 0 0000 00 01 94 90 0D 85 Dialog Frame Input IP Address 168 0 Input Subnet Mask 255 25531255 40 0 Input Gateway IP 420 ET Figure 3 4 Assign an IP Address with the same Subnet Mask of your computer avoiding any IP conflict with other network devices When you press Confirm button the IP address will be refreshed in 2 3 seconds EXBrowser V1 20 pm IP Address Subnet Mask MAC P EX 9132C 2 192 168 0 100 255 255 255 0 0000 00 01 94 90 0D 85 Dialog Frame r Input Password ET O Online 1 Figure 3 5 After click Confirm button and then Input Password reguest will be pop up on screen see Figure 3 5 Please simply press Confirm button and the new device s IP will be changed and save in table if you changed it EXBrowser 71 20 File View Help ADEL Bum IP Address A Subnet Mask Gateway IP MAC 192 168 0 101 255 255 255 0 00 01 94 90 0D 85 Figure 3 6 19 EXBrowser Modify MAC Modify MAC gt Dialo
6. If everything is ok you can close the browser now Note If the domain of the converter is different from that of the computer running the browser the login page won t appear unless the converter s Gateway Address has been correctly set 30 Factory Default Setting If you forget the setup password or have incorrect settings making the converter inoperable there are two ways to reset the setting and the following procedures can be used to reset all settings to factory default A 1 Please turn on the power and then use any point tip to push Reset button for 5 seconds The password will be reset to the factory default as empty 31 5 Setting Verification After complete the wiring and parameter setting we should verify if the setting is correct This chapter will introduce how to use a single computer to test if the converter behaves well The operating system can be Windows 95 98 ME XP 2000 Vista 7 The Hyper Terminal utility should be installed on your PC see Figure 6 1 It can be found in your Windows installation CD The wiring architecture is similar to RS 232 Wiring in chapter 3 and the Serial Device is replaced by the PC s COM 1 The same PC also plays the roll of the Remote Host The following topics are covered in this chapter Hyper Terminal for TCP IP WinSock Hyper Terminal for COM Port Data Transmission 32 Hyper Terminal fo
7. outs and Cable Wiring DC In Jack _ RJ 45 Pin Assignment RJ45 Port Pin Signal 1 Tx 2 Tx 3 Rx 6 Rx RS 232 Pin Assignment The pin assignment scheme for a 9 pin male connector on a DTE is given below PIN 1 N A PIN 2 RXD PIN 3 TXD PIN 4 DTR PIN 5 GND PIN 6 DSR PIN 7 RTS PIN 8 CTS PIN 9 N A 41 RS 232 Wiring Diagram Serial Device EX 9132C 2 2 RX 3 TX 3 TX 2 RX 5 GND 5 GND 7 RIS 8 CTS 8 CTS 7 RTS RS 422 Pin Assignment The pin assignment scheme for a 4 pin RS 422 is given below beers 0000 PIN 1 R PIN 2 R PIN 3 T PIN 4 T RS 422 Wiring Diagram Serial Device EX 9132C 2 R 3 T R 4 T T R 2 RS 485 Wiring Diagram Serial Device EX 9132C 2 D D D D 42
8. ss will start counting 36 My e 1 10 HyperTerminal Connected 0 00 24 ko detect Microsoft Shortcut to Bim bOpLO Hyper Terminal Figure 6 5 37 Hyper Terminal for COM Port Initiate another Hyper Terminal as COM Port Terminal in Figure 6 3 select COM 1 or other COM port instead of TCP IP Winsock Set the COM port Properties to be the same as those set for the Serial Port 1 of the converter Id Connect To To De peace in United States IM pm cdi Figure 6 3 38 Data Transmission When all steps described above are finished type any texts on the COM Port Terminal and check if the texts are also displayed on the TCP IP Winsock Terminal Alternatively check if the characters typed on the TCP IP Winsock Terminal are also displayed on the COM Port Terminal If yes then all settings are correct and the converter can operate properly 39 Appendix FAQ Why can t the EXBrowser exe detect the converter on the network A Please check if the power is properly plugged to the converter H3 ifthe network cable is properly connected between the converter and the Hub Please refer to the Hardware Installation steps in Chapter 3 Q Why can t I use IE to setup the converter A Please check if the network domain of your PC is the same as that of the converter 40 Appendix B Pin
9. the following chapters RS 232 485 422 Digital I O Through EX 9132C 2 D I O can transform the status of sensor into the TCP IP package data and send out by Ethernet Data Stream The EX 9132C 2 must indicate the IP address and COM Port or activate the indicated Digital output Remote WinSock must indicate the EX 9132C 2 Connect the data wires between the EX 9132C 2 and the RS 485 RS 422 device Follow the parameter setup procedures to configure the converter see the following chapters Left Side Power Supply EX 9132C 2 TCP IP converter device is powered by a single 9VDC inner positive outer negative power supply and 500mA of current A suitable power supply adapter is part of the packaging Connect the power line to the power jack at the left side of EX 9132C 2 TCP IP converter device and put the adapter into the socket If the power is properly supplied the PWR red color LED will be on DC In Power Outlet gt Ethernet LAN Port amp Reset Button gt Ethernet LAN Port The connector for network is the usual RJ45 Simply connect it to your network switch or Hub When the connection is made the LAN LED indicator will light up When data traffic occurs on the network red DATA LED indicator will blink during data transferring and receiving Reset Button If you forget the setup password or have incorrect settings which makes e Net TCP IP converter inoperable First turn off the power
10. AN Speed Support 10 100 Mbps Ethernet auto detected Server Client Dual Modes EX 9132C 2 converter device can be configured as network server or network client In the client mode it can be installed in network which is protected by NAT router or firewall without a real IP address Web based Setup Parameters setup is based on HTTP protocol by using standard browsers IE and Netscape No special software would be required Built in Security Control Security protect by login password to prevent intruders Remote Update Firmware can be updated directly via Ethernet network to keep up with latest network standards Product Specifications CPU ARM Cortex M3 32 bit processor SOMHz RAM 64K Bytes SRAM 256K Bytes Flash ROM Ethernet Port Type RJ 45 Connector Speed 10 100 M bps Auto Detect Protocol ARP IP ICMP UDP TCP HTTP DHCP ICMP e Mode Server Client UDP Client Virtual COM Pairing Setup HTTP Browser Setup IE amp Netscape Security Login Password e Protection Built in 1 5KV Magnetic Isolation Serial Port e No of Ports RS 232 1 Port and RS 232 422 485 Auto Detect 1 Port e Port Type DB9 male 1 and Terminal Block 7pin 1 e Speed 300 bps 115 2K bps e Parity None Odd Even Mark Space e Data Bit 5 6 7 8 e Stop Bit 1 2 e Port 1 e One RS 232 Signals Rx Tx GND RTS
11. CTS DTR DSR DCD e Port 2 e One RS 232 422 485 Port Auto Detect e RS232 Signals Rx Tx GND e RS 422 Signals Rx Rx Tx Tx Surge amp Over Current Protect e RS 485 Signals Data Data Surge amp Over Current Protection e Built in RS422 RS485 Pull High Low Resistor Digital I O Port Digital TTL I O 8 pins Socket Port Connection I Connection 15 ESD for all signal Watch Dog Function Virtual Support Windows 2000 2003 XP Vista 7 Firmware On line Updated Via Ethernet Power DC 9 24 V 500mA LED Lamp PWR Green DATA Red Blink during data transferring and receiving LAN Red for 10 Mbps Green for 100 Mbps SYS Red Blink Environment Operating Temperature 0 C 70 Storage Temperature 10 C 80 C Dimensions 115 90 27 mm W D H WEIGHT 140 gm RoHS Compliant with RoHS Regulatory Approvals FCC CE WARRANTYT 1 year EX 9132C 2 Description amp Installation Product Panel Views Top Side DC In Power Outlet Ethernet LAN Port Reset Button Serial I O Port RS 232 485 RS 422 o E PERT EX 9132c 2 2 10 100M 1 Port RS232 1 Port RS232 4221485 Over IP Adapter Serial I O Port RS 232 LED Indicators Right Side Serial I O Port of RS 232 and RS 232 422 485 Connect the serial data cable between the converter device and the serial devices Follow the parameter setup procedures to configure the converter see
12. Operation Manual of EX 9132C 2 Serial to TCP IP Converter Version 1 1 0 25th Jan 2010 1 Table of Contents Introduction te eerte Exe Sere Checklist Block ea petu Features ec D Product Specifications EX 9132C 2 Description Product Panel Views 22 442 Top Side varsel Right Side asa aa EROR VAR AT Rear sasa aaa aa se eiie Ea a a NG a a a LED Indicators 4 4 5361342455038 69838866 2E EE IEEE Eo ao e RA A CEPR ERU Bae Wiring Architecture RS 232 M RS 422 RS 485 jp Greske EX 9132C 2 Installation Power Supply Ethernet Port ir Eee KANE Serial Port sasana ae ea a a ag aan aaa a aa senker RS 485 RS 422 ss Dip Switch kaso aaa a a aa sses iros sisses cl 4 EX 9132C 2 Configuration Initial IP Configuration Device Management Utility of EXBrowser Menu View vaner ss eveE n NU ke CES Ak epus Menu Config ass gaga Web Console Configuration eene Controller Status saadan Controller Setup ussssssesvecess esso ag naa Na aaa GL Controller Updated eaaa ux Ex E aes eiue aaa Factory Default Setting 5 Setting Verification
13. ation will be required looking for technical support Serial number It is product serial number code in the converter device and has been provided by factory 22 Ethernet MAC Address Converter is unique MAC Media Access Control address used by Ethernet Password This field is the administration password for authentication Factory default is empty However it is not recommended to leave it empty in field operation If you could not login it means you have to key in the password If you do not know the password you can turn off the power and then use any point tip to push Reset button and hold it to turn on the power at the same time for 5 seconds The password will be reset to the factory default as empty Converter device uses the same password protection mechanism commonly used in Windows NT or UNIX If there are more than 3 consecutive failures in password check during login the login function will be disabled for 15 minutes During this 15 minutes period even if you supply correct password login will not proceed This prevents intruders from finding the password by computer generated program 23 Parameter Setting Page The Parameter Setting Page Type the correct password in the Password field and click the Confirm button in the Login Setting page then the Parameter Setting page will be shown see Figure 3 10 Note If you forget the password or can t lo
14. code density enabling smaller memories reducing pin count and low power consumption The central core of ARM Cortex M3 processor based on 3 stage pipeline Harvard bus architecture incorporates advanced features including single cycle multiply andhardware divideto deliver an outstanding efficiency of 1 25 DMIPS MHz The ARM Cortex M3 processor also implements the new Thumb 2 instruction set architecture which combined with features such as unaligned data storage and atomic bit manipulation delivers 32 bit performance at a cost equivalent to modern 8 and 16 bit devices Product Features Data Conversion between RS 232 and RS 422 485 and Ethernet EX 9132C 2 converter device RS 232 1 port RS 232 422 485 1 port data signal into the TCP IP package data signal and send them out with the Ethernet Data Stream or convert the TCP IP package data signal into serial device data signal Socket Communication EX 9132C 2 is provided one socket connection Digital I O Activating Optional EX 9132C 2 provides eight TTL of digital I O Convert the sensors statuses the sensors are connected to the converter into the TCP IP package data and send them out with the Ethernet Data Stream or use the TCP IP package data to activate deactivate the specified digital outputs Dynamic IP Configuration Support DHCP client mode simplifying network address configuration and management Dual L
15. etup process In the browser URL field set the IP address of device directly to enter the Login Setting page please follow the steps below Open your browser This chapter will use IE as an example In the browser URL field type the IP address of the converter directly and press ENTER The IP address is what you set using the Device Management Utility as EXBrowser To press fourth icon of Web Browser on function bar and a Login Setting Screen will be shown see Figure 3 9 to login into the device Alternatively if the IP address of the converter is already known you can connect to the converter directly by providing its IP address in the URL field 21 of browsers lod EGGENE 1 Edit View Favorites Tools Help CERISE ix A Jo Search S G Favorites A media B Address http 192 168 0 102 8 Ee Serial To Ethernet Converter Login setting System time elapsed Day Hour Min Sec 00244 Firmware version 6519 2009 01 55 57 Serial number wesn st4 00 Ethernet MAC address 00 01 94 90 00 72 Password Figure 3 9 Login Setting Page Field Description System time elapsed The time elapsed since start of this device in Day Hour Minute Second format This information can be useful in identifying the reliability of system Firmware version Converter firmware is identified by date code This inform
16. g Frame To click the device on the existing devices list in the EXBrowser table and then the function bar will be enabled To press Third icon of Modify MAC on function bar and a dialog frame table will be shown see Figure 3 7 EXBrowser 1 20 255 255 255 0 00 01 94 90 0D 85 Dialog Frame Input MAC 00 01 94 90 0D 85 Figure 3 7 Input Password gt Dialog Frame After click Confirm button and then Input Password request will be pop up on screen see Figure 3 8 Please simply press Confirm button and the new device s MAC will be changed and save in table if you changed it re EXBrowser V1 20 qu EX 9132C 2 192 168 0 101 255 255 255 0 00 01 94 90 0D 85 Dialog Frame Input Password ET Figure 3 8 20 Web Browser Configuration The following topics are covered in this chapter Serial To Ethernet Converter Setup e Login Setting e Login Setting Page Field Description e Parameter Setting e Parameter Setting Page Field Description Login Setting In addition to basic IP address and subnet mask specific device settings can be set through HTTP protocol with popular browsers e g Internet Explorer Netscape etc Setup of the converters is as easy as surfing on WWW no special software will be required Setup converter device is as easy as surfing on WWW no special software will be required Popular Browsers such as IE or Netscape can easily do the s
17. gin successfully please contact the manufacturer directly Parameter setting IP address 1192 168 0 102 Subnet mask 2552552550 Gateway IP fo 0 0 0 DHCP Client Disable Auto Reset No data input 0 Hours Device ID EX 9132C 2 Serial VO Port1 Local port Socket mode 100 TOP Server Remote IP Port TCP Client UDP 0 Interface RS232 vi Baudrate 9600 Parity Data bit Stop bit None 8 v Force off line time No data input 0 Minute Packet collect time Txo Rx mSec Serial NO Port 2 0 Local port Socket mode Remote IP Port TCP Client UDP 101 0000 Auto Detect 9600 rs TCP Server 0 w Serial Port 1 0 Local port Socket mode Remote IP Port TCP Client UDP Interface Baudrate Parity Data bit Stop bit Force off line time No data input Packet collect time 100 TCP Server v 0 0 0 0 0 R5232 v 9600 None 8 viii 0 Minute Tx 0 Rx 0 mSec Serial I O Port 2 Local port Socket mode Remote TCP Client UDP Interface Baudrate Parity Data bit Stop bit Force off line time No data input Packet collect time Local port Socket mode Remote IP Port TCP Client UDP Configuration 101 0 0 0 0 Auto Detect 9600 None Minute RX 0
18. lient mode for certain serial port Interface of serial I O It provides an Auto Detect function and just depends on the connected serial device s interface as RS 422 or RS 485 Baudrate Baud Rate 300 115200 bps Parity Data bits Stop bit Parity None Even Odd Space Mark Data Bits 5 6 7 8 Stop Bit 1 or 2 Force off line time It is for setting the off line time period of device will be taken when there is no date input The parameter can be from 0 to 99 and the time unit is Minute Packet Collect Time It is for setting a packet collecting period of the device serial port s Tx and Rx The parameter can be from 0 to 999 and the time unit is mSec 28 Interface of serial I O RS 232 TxD RxD for data stream no flow control 8 232 RTS CTS TxD RxD for data stream RTS CTS for flow control 5 485 Half duplex Half duplex RS 485 interface RTS for driver enable disable o RS 422 Full duplex Full duplex RS 422 interface 29 Controller Updated Press Update Button after finish the detailed parameter setting The converter will save all parameters into internal non volatile memory and then reboot see Figure 5 3 It takes about 5 seconds to complete the whole process and a new login page will be presented see Figure 5 1 Controller updated Now restarting Figure 5 3 You can re login and check if all parameters have been correctly saved
19. ly all kinds of devices EX 9132C 2 is a full set converter device with two serial ports as one is a RS 232 port and another is a RS 232 422 485 Auto Detect and it provides one socket per connection port This operation manual will guide you step by step to learn the various functions of the EX 9132C 2 converter The following topics are covered in this chapter Overview Block Diagram Product Features Product Specifications Overview EX 9132C 2 converter is designed to make your industrial serial devices Internet ready instantly ARM Cortex M3 CPU of EX 9132C 2 converters makes them the ideal choice for connecting your RS 232 and RS 422 or RS 485 serial device such as PLCs meters and sensors to an IP based Ethernet LAN making it possible for your software to access serial devices anywhere and anytime over a local LAN or the Internet ARM Cortex M3 CPU Series converters ensure the compatibility of network software that uses a Standard network API Winsock or BSD Sockets by providing TCP Server Mode TCP Client Mode and UDP Mode Model EX 9132C 2 provides 1 socket connection for remote management ARM Cortex M3 CPU Series Virtual COM driver and software that works with COM port can be set up to work over a TCP IP network in no time This excellent feature preserves your software investment and let you enjoy the benefit of networking your serial devices instantly ARM Cortex M3 CPU series con
20. mode is enabled and there s a DHCP server on the network this field will be assigned by DHCP server automatically DHCP client DHCP client mode could be enabled disabled statues If DHCP is enabled there should be a DHCP server on the network If DHCP is disabled IP address Subnet mask and Gateway address should be manually assigned Auto Reset It is for resetting when the device has been disconnected or some reasons the data stop transmitting for a while You can prevent it and restart the device after waiting a while 1 99 hours as your settings 25 Device ID Report You may Enable or Disable to collect the device ID report and assigne ID number for the converter devices Available ID is 0 65535 In TCP mode if this parameter is enabled every time when the socket is connected e Net TCP IP converter will immediately report its device ID in the following formats Serial 1 nnnnnA LF CR Serial 2 nnnnnB LFJ CR Digital I O nnnnnC LF CR The total length is 8 bytes where nnnnn is a 5 digit device ID assigned by the user LF is decimal 10 CR is decimal 13 Login Password For security and management issues you may setup the Login Password This administration password uses to login converter parameter setting pages It may be empty or up to 15 characters long Serial Port 1 RS 232 This converter device model provides one serial port as RS 232 interface for
21. n one converter on the network please shut down or disconnect other converters Otherwise the EXBrowser exe can not detect the converter Due to the nature of broadcast UDP packets EXBrowser has following characteristics Broadcast packets are not limited by subnet Even if the IP address of the converters and the computer running EXBrowser that do not belong to the same subnet it still works fine Broadcast packets can not pass routers EXBrowser can only be used to monitor devices with computer running EXBrowser in the same segment of local area network 2 EXBrowser 1 20 EEK File View Help IP Address Subnet Mask 192 168 0 100 255 255 255 0 0 0 0 0 00 01 94 90 0D 85 Figure 3 1 17 EXBrowser View View gt Refresh There are two ways for refreshing the status of existing devices You may select the item View to refresh the status of existing devices on LAN Another is to click the icon as red color remark as below EXBrowser will send another query to get updated information see Figure 3 2 Note Always run the Refresh after any data change 58 EXBrowser V1 20 File View Help Subnet Mask 192 168 0 100 255 255 255 0 00 01 94 90 0D 85 Figure 3 2 File gt Exit Alt F4 Exit from the program see Figure 3 3 2 EXBrowser V1 20 File View Help 84 Device Name IP Address Subnet Mask EX 9132C 2 192 168 0 100 255 255 255 0 00 01 94 90 0D 85
22. r TCP IP WinSock Initiate Hyper Terminal from the Start Menu in Windows see Figure 6 1 give terminal name choose an icon and press button see Figure 6 2 accessb ty Entertanment E System Address Book Command Promer 8 notepad Fant E HyperTerminal Program Compatiblty Wd WS Network Connections ig Syneheonee f Network Setup Wizard Bl Neer Connection Wizard Mj Remote Desktop Connection Windows XP Professional Start Figure 6 1 33 rk erak Espiorer Microsoft Gutlook Shortcut bo Etm Figure 6 2 Select TCP IP Winsock option at the Connect using field see Figure 6 3 34 8 Counplegen Ured Sise 11 Area code Phonerumber p bopti HyperTerminal Figure 6 3 After OK button is pressed Figure 6 4 appears Enter the converter s IP address e g 192 168 123 10 at the Host address field and the Socket port number set for the Serial Port 1 at the Port number field e g 4660 The Socket type of the Serial Port 1 should be TCP Server 35 MAP connect Ta TJ Connecting Shorbcuk to im HyperTerminal Figure 6 4 After OK button is pressed Figure 6 5 appears If the Hyper Terminal connects with the converter successfully the time clock at the left lower corner Connected hh mm
23. steps mentioned above and the LED indicators are as shown in above diagram the converter is installed correctly You can use the Setup Tool EXBrowser exe to setup the IP Address To proceed the advanced parameter setup please use a web browser IE or Netscape to continue the detailed settings 15 EX 9132C 2 Converter Configuration Initial IP Configuration When sett up your converter for the first time the first thing you should do is to configure the IP address This chapter introduces the method to configure the device server s IP address For more details about network settings please see the Network Settings section in Chapter3 Web Console Configuration The following topics are covered in this chapter Device Management Utility EXBrowser View EXBrowser Modify IP EXBrowser Modify MAC Device Management Utility On PC we provide Device Management Utility named EXBrowser exe which is an executable program in Windows 32 bit environments EXBrowser setup tool is used to detect and setup the installed converters It uses UDP broadcast packets to query and configure converters on the network When you activate the tool it will detect the existence of the installed converters and depict the converters status such as IP address Subnet Mask MAC Address and Device ID see Figure 3 1 The Setup Tool only can setup one converter at a time Thus if there are more tha
24. taken when there is no date input The parameter can be from 0 to 99 and the time unit is Minute Packet Collect Time It is for setting a packet collecting period of the device serial port s Tx and Rx The parameter can be from 0 to 999 and the time unit is mSec Serial O Port 2 RS 232 422 485 This converter device model is provided second serial port as RS 232 422 485 Auto Detect interfaces for connecting the extension serial device Local Port Socket Mode Remote IP amp Port This converter device provides 1 socket connection port p Port number 27 socket port is assigned for the serial port It s 16 bit numbers ranging from I to 65535 Because the numbers below 1000 are used for specific purposes e g 80 is for HTTP protocol we suggest you use the numbers larger than 1000 Generally the port number 4660 is used for the serial communication However you should specify different port number for each serial port Socket type Server TCP protocol passive open to be connected from the TOP clients n Client TCP protocol active open connects to the TCP server UDP Client UDP protocol connectionless Remote IP address The server IP address and socket port would be connected in TCP Client and UDP Client mode for certain serial port Remote socket port The server socket port would be connected in TCP Server TCP Client and UDP C
25. verter supports manual configuration via the handy web browser console and many protocols including TCP IP UDP HTTP DHCP ICMP and ARP They are the best solution to network your serial devices Package Checklist ARM Cortex M3 CPU products are shipped with the following items 1 unit of EX 9132C 2 converter I unit of Power Adaptor 9V DC 500mA Optional Quick Installation Guide in Documentation amp Software CD NOTE Please notify your sales representative if any of the above items is missing or damaged Block Diagram Low cost devices usually are equipped with low speed processors and limited memories In reality they have neither the capability nor practicality to manage complicated network TCP IP protocols The ARM Cortex M3 32 bit processor has been specifically developed to provide a high performance low cost platform for a broad range of applications including microcontrollers automotive body systems and industrial control systems networking by converting data stream between network TCP IP and popular serial port signals Instead of processing TCP IP packets directly devices need only deal with those interface signals which greatly simplifies the complexity of TCP IP network in linkage The ARM Cortex M3 processor provides outstanding computational performance and exceptional system response to interrupt while meeting low cost requirements through small core footprint industry leading
Download Pdf Manuals
Related Search