Home

U S E R ` S M A N U A L

1. BM is a registered trademark of International Business Machines Corporation of the United States Macintosh is a registered trademark of Apple Computer Inc of the United States 48 REFERENCE CINEMA SCREEN DISPLAY LIMITED WARRANTY WHAT YOUR WARRANTY COVERS Any defect in materials or workmanship FoR HOW LONG AFTER YOUR PURCHASE One year for labor charges One year for parts The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm whichever comes first WHAT WE WILL DO Exchange your unit with a new or at our option refurbished unit How vou GET YOUR UNIT REPAIRED Call 1 800 433 8974 and have your unit s date of purchase and model serial number ready A representative will troubleshoot your problem over the phone f the representative determines that you should receive a replacement arrangements will be made to deliver a new or refurbished unit and pick up your defective display all in one trip at no cost to you WHAT YOUR WARRANTY DOES NOT COVER Customer instruction Your Owner s Manual clearly describes how to install adjust and operate your display Any additional information should be obtained from your dealer Signal reception problems not caused by your Cinema Screen display Damage from misuse or neglect Batteries A display purchased or serviced outside the U S A Acts of God such as but not limited to lightning damag
2. 0 The timer starts when the Sleep display turns off TO CHECK THE REMAINING TIME all Once the sleep timer has been set and the menu has turned off press the SLEEP button once The remaining time is displayed then disappears after a few seconds When five minutes remain the remaining time appears until it reaches zero CANCELLING THE SLEEP TIMER 1 2 40 Press the SLEEP button twice in a row The sleep timer is canceled NOTE After the power is turned off with the sleep timer a slight current is still supplied to the monitor If you do not plan to use the system for a long period of time turn the power off with the remote or on the unit REFERENCE TECHNICAL INFORMATION 1 SETUP AND This section contains technical reference information CONNECTIONS about your Cinema Screen monitor as well accessory and warranty information 2 THE MENU SYSTEM 3 REFERENCE 41 REFERENCE INSTALLING THE CINEMA SCREEN MONITOR IMPORTANT This device cannot stand on its own Be sure to use a stand or original mounting unit For correct installation and mounting it is strongly recommended to use a trained authorized Cinema Screen dealer Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer Product warranty does not cover damage caused by improper installation ATTACHING OPTIONAL MOUNTS OR STAND TO THE CINEMA SCREEN MONITOR The C
3. Y 3 REFERENCE 21 THE MENU SYSTEM Basic OPERATIONS POWER To turn the monitor on and off 1 2 Plug the power cord into an active AC power outlet Press the ON OFF button on the remote control or the unit The monitor s POWER STANDBY indicator turns green when the monitor is on Press the ON OFF button on the remote control or the unit to turn it off The monitor s POWER STANDBY indicator turns red and the standby mode is set only when turning off the unit with the remote control VOLUME To adjust the volume 1 Press and hold the VOL AW button on the remote control or the unit to increase to the desired level 2 Press and hold the VOL V button on the remote control or the unit to decrease to the desired level Note External speakers are required for sound MUTE Press the MUTE button on the remote control to reduce the sound to an inaudible level Press MUTE again to restore the sound 22 THE MENU SYSTEM NAVIGATING THE Menus You can adjust monitor options through the Cinema Screen monitor s menu system To access the main menu press the MENU button on the remote control or MENU OK on the front of the monitor There are a few things you need to know to navigate through the menu system The navigation buttons are the set of arrow shaped buttons in the middle of the remote See illustration on right Use the A and V buttons on the remote to move the menu highlight up and down
4. 3 REFERENCE SETUP AND CONNECTIONS CONTENTS OF THE PACKAGE Cinema Screen monitor Power cord RGB cable Mini D Sub 15 pin to Mini D Sub 15 pin connector Remote control unit with two AA batteries User s manual It is highly recommended that you have your Cinema Screen monitor installed by a professional If you are installing the monitor yourself refer to the Reference section NOTE If you are planning on attaching the floor stand to your Cinema Screen monitor and not the optional wall mount unit you may want to use the safety metal fittings provided to give your monitor extra stability The safety metal fittings attach to the back of the screen and can then be used to secure the monitor to the wall with strong wire Contact your trained authorized Cinema Screen dealer for professional installation SETUP AND CONNECTIONS Part NAMES AND FUNCTIONS FRONT ViEw VoiuMr Down Up irr Ricur Meny OK Menus OK If no menu is displayed brings up the menu If a menu is displayed press to select a highlighted option Votume Adjusts the volume When an on screen menu is being displayed moves highlight up and down A and VW Lert AND Ricur When Zoom mode is on press OK on the remote to turn ZOOM on and bring up the zoom icon press Right to enlarge the image or Left to reduce the image When a menu is being displayed used to navigate through menu q and y 6 PowER StAN
5. AUDIOS3 Connect audio here 11 CMPNT1 Connect Laser discs etc here Eo uomo OF SETUP AND CONNECTIONS BATTERY INSTALLATION Remove the battery compartment cover from the back of the remote control insert batteries Make sure the polarities and are aligned correctly Replace cover CONNECTING AN HD RECEIVER RCA and PROSCAN HD high definition receivers come equipped with an RGB output jack for optimum quality Using the RGB cable provided connect the HD MONITOR OUT jack on the back of your HD receiver to the RGB1 HD MONITOR INVAUDIO1 IN jack on the back of the Cinema Screen monitor If your HD receiver does not have the type of jack pictured on the right connect your HD receiver using the component video jacks and RCA cable For more information on HD receiver connections see your HD receiver user s manual THe Back or THE HD RECEIVER RGB cable NAC ACCESS CARD o R e DIGITALAUDIO YOR Launo VIDEO gt SVIDEO HOM OUTPUT CONTROL SATELLITE X IN PHONE JACK QUTTOTV ANTENNAS ANTENNA ii 0000000 000000 l loooo000 HD MONITOR OUT jack SETUP AND CONNECTIONS CONNECTING YouR VCR OR LAsERDISC PLAYER Use common RCA cables not provided to connect your VCR or laserdisc player to your Cinema Screen monitor To connect your VCR or Laserdisc player 1 Turn off the power to the monitor and VCR or laser disc player 2 Connect one e
6. Setting the Film Mode option to Auto will reduce flickering and improve the quality of video images AUTO The display will recognize and correct any flickering that occurs in an image ON All images are displayed in film mode OFF Film mode is off To turn FILM MODE to AUTO 1 From the main menu highlight and select FUNCTION The FUNCTION menu is displayed Highlight the FILM MODE option 3 Use the p gt button to scroll through the three modes until the AUTO is displayed 4 Press the button to return to the FUNCTION menu optons You can continue making adjustments within the FUNCTION menu return to the previous menu by pressing GO BACK or press CLEAR to exit the menu system RESETTING TO DEFAULT VALUES The RESET function allows you to reset al adjustments to the factory default settings Remember this will reset al adjustments you have made in all menus To reset to the factory default settings 1 From the main menu highlight and select OPTIONS The OPTIONS menu is displayed 2 Highlight the RESET function and press OK 3 The RESET screen is displayed 4 Use the A or V button to highlight the RESET option and press OK or MENU The RESET screen will display the message NOW RESETTING When the settings are restored to the factory default you are returned to the RESET screen When you are done press GO BACK to return to the FUNCTION menu or pres CLEAR to exit the menu system 34
7. This is the FUNCTION menu with the FILM MODE option highlighted These are the RESET screens Choose the RESET option if you want to reset ALL options in all menus back to the factory default THE MENU SYSTEM THE OPTIONS menu SETTING THE AUDIO INPUTS The Cinema Screen s audio sources are programmable to the each of the display s video sources For example you can program AUDIO source to work with the RGB2 video source This feature is generally used only for commercial applications 1 From the main menu highlight and select OPTIONS The OPTIONS menu is displayed 2 Highlight the one of the audio input options 3 Use the M button to scroll through the available video sources The modes scroll as follows r VIDEO1 VIDEO2 VIDEO3 HD DVD1 RGB1 RGB2 RGB3 4 When the desired mode is selected press the 4d button to return to the OPTIONS menu items You can continue making adjustments within the OPTION menu press GO BACK to return to the previous menu or press MENU or CLEAR to exit the menu system SETTING THE BNC CONNECTORS By default the BNC inputs are set to RGB1 or composite video If the component you are connecting to the BNC jacks doesn t have composite video jacks you can set the BNC inputs to act as component video 1 From the main menu highlight and select OPTIONS The OPTIONS menu is displayed 2 Highlight the BNC SELECT option 3 Usethe j gt
8. Use the lt q and p buttons to move the highlight and change settings Press the GO BACK button on the remote to return to a previous menu You can return the Cinema Screen monitor to the factory settings at any time by using the RESET option in the OPTIONS menu Remember if you choose to reset ALL settings will return to the factory settings On ScreEN MENU OPERATION To access the main menu press the MENU button on the remote The MAIN MENU is displayed on the screen The main menu contains a list of all the menus that control your monitor To select a menu use the up down arrow buttons on the remote to highlight the desired menu When the desired menu is highlighted press the OK or MENU button to select Note Different components use different types of input RGB video etc Some menu options apply to only one type of input so they only appear when they apply to the currently active input For example the COLOR and TINT options in the PICTURE QUALITY menu only appear when you are adjusting standard video input VIDEO1 VIDEO2 VIDEO3 cue SP Nro ONO Q Q MENU l CLEAR These are the buttons on the remote you use to navigate through the monitor 5 on screen menu system MAIN MENU This is the main menu with the PICTURE Quality option highlighted Press OK to bring up the highlighted menu 23 THE MENU SYSTEM THE PicTURE QuALITY MENU SETTING THE PicTurE MODE The Cinema Screen monitor has preset viewi
9. Changes the level of high frequency sound BALANCE Changes the balance of the left and right speakers MENU OPERATIONS To access the AUDIO menu 1 28 From the main menu highlight and select the AUDIO option The AUDIO menu is displayed Use the A and V arrow buttons on the remote to highlight an option for example BASS Use the lt q and p gt buttons to adjust to the desired setting You can continue adjusting audio settings press GO BACK to return to the main menu or press CLEAR to exit the menu system This is the AUDIO menu with the BASS option highlighted Press the rightarrow button to select it THE MENU SYSTEM THE SCREEN MENU The SCREEN menu allows you to set the monitor to automatically select the correct mode for viewing a particular movie and to change the positions of on screen menus SELECTING A VIEWING SIZE When viewing with a component other than your HD receiver you can set the screen mode to one of four screen sizes to suit the type of input you are watching Select the screen mode with the CINEMA button on the remote control The screen sizes are as follows FILL expands in both vertical and horizontal directions while the correct proportions are maintained The picture is not distorted just closer NORMAL displays a picture with a 4 3 aspect ratio standard video Because this mode fills the screen vertically but not horizontally black bars will appear on the right and left sid
10. Cinema Screen Monitor 36 3 H X 20 4 V inches Screen Size 921 H X 518 4 V mm diagonal 42 Aspect Ratio 16 9 Resolution 853 H X 480 V pixels Color Reproduction 256 levels 16 770 000 colors Input Signals RGB NTSC 3 584 43 PAL B G M N PAL6O RGB input terminals SECAM HD DVD DTV Visual 1 mini D sub 15 pin Visual 2 BNC R G B H CS V X1 Visual 3 DVI 29 pin X 1 Video input terminals Visual 1 RCA pin X 1 Visual 2 BNC X 1 Visual 3 S Video DIN 4 pin X 1 DVD HD DTV Visual RCA pin Y P C PR C Audio Stereo RCA X 3 External Control D sub 9 pin X1 RS 232C Sound Output 7W 7W at 6 to 8 ohm Power Supply AC120V 50 60Hz Current Rating 4 2A maximum Power Consumption 395W typical Dimensions WxDxD 1084 X 648 X 91mm w o stand 41 3 X 25 5 X 3 5 inches w o stand 1084 X 746 X 360mm with stand Net Weight 32 Kg 70 6 ibs w o stand Environmental Considerations 0 C to 40 C 32 F to 104 F Operating temperature 20 to 80 Humidity 0 to 1900m 0 to 6230 ft Altitude 10 C to 50 C 14 F to 122 F Storage temperature 10 to 90 Humidity 0 to 3000m 0 to 9840 ft Altitude Power on off Input source select Front Panel User Controls Volume up down OSM control Other Features Power Management plug and play DDCI DDC2b RGB3 DDC2b only Accessories Remote control with two AA batteries RGB cable Mini D sub 15 pin to Mini D sub 15 pin conne
11. NORMAL WARM PRO COOL f NOTE If you don t push the q or p button within 5 seconds the current setting is accepted and the previous screen reappears 4 Once the desired color temp is selected press OK or MENU If you choose the PRO setting the WHITE BALANCE screen appears It allows individual setting of white and dark balance for each color red green and blue GAIN This adjusts the color balance for light bright colors BIAS This adjusts the color balance for dark colors To change the white balance GAIN setting 1 Highlight the RED GREEN or BLUE GAIN option and press the J gt button The GAIN screen for that color appears 2 Adjust the balance using the qd and i keys NOTE If you don t push the lt or y button within 5 seconds the current setting is accepted and the previous screen reappears 3 When you have the desired setting press OK or MENU The GAIN is adjusted and you are returned to the WHITE BALANCE screen 4 When you completed all the desired white balance adjustments Press the GO BACK button to return to the PICTURE menu You can continue adjusting picture settings return to the main menu or press CLEAR to exit the menu system 26 COLOR TEMP UMPROE This is the COLOR TEMP screen with PRO as the current selection This is the WHITE BALANCE screen with the RED GAIN option highlighted This is the R GAIN red gain screen THE MENU SYSTEM REDUCING NOISE IN THE PIC
12. SXGA XGA SVGA VGA configuration If you need to install a new board see the manual that comes with your new graphics board for installation instructions 3 The Cinema Screen monitor provides signal compatibility with VESA 1280210249 60MHz SXGA However we recommend not using this resolution due to image readability on the monitor s 853 X 480 native pixel resolution panel 4 Use the signal cable that s supplied to connect your PC or Macintosh computer to the Cinema Screen monitor For Macintosh you will need a monitor adapter not supplied to connect to your computer s video port 5 Turn on the monitor and the computer 6 If the Cinema Screen monitor goes blank after a period of inactivity it may be caused by a screen saver installed on the computer you ve connected to the monitor When using a Macintosh with the Cinema Screen monitor the following three display standards are supported using the included Macintosh adapter 13 fixed mode 16 fixed mode and 19 fixed mode The 13 fixed mode is recommended for the Cinema Screen monitor Mini D suB 15 Pin VGA SIGNAL COMPOSITION Pin No Signal to be connected GREEN or sync on Green BLUE No connection GND RED GND GREEN GND BLUE GND Co P5 Qi No connection SYNC GND paai m pd No connection SDA ae a wih H Sync owe dx V sync SCL m Or 43 REFERENCE SPECIFICATIONS Product Name PSP42300
13. Screen monitor To autotune your components to the buttons on the remote 1 From the main menu highlight and select the AUTOTUNING SETUP option The AUTOTUNING SETUP menu is displayed 2 Highlight an option which corresponds to a component which you ve connected For example if you have a DVD player connected highlight the DVD BUTTON option This is the AUTOTUNE menu with the DVD BUTTON option highlighted 3 Use the gt button to scroll through the output choices Select the choice which corresponds to the jacks you used to connect the DVD player In the example illustration on the right the DVD button on the remote will operate the component connected to the CMPNT1 jacks the DVD player 4 When the desired option is displayed press the lt q button to return the the AUTOTUNING menu options You can continue making adjustments within the OPTIONS menu press GO BACK to return to the previous menu or press CLEAR to exit the menu system 39 THE MENU SYSTEM SLEEP TIMER The sleep timer is a feature that allows you to set the monitor to turn off after a prescribed amount of time It can be set to turn the power off after 30 60 90 or 120 minutes SETTING THE SLEEP TIMER 1 3 Press the SLEEP button on the remote to turn on the timer The default is 30 minutes Press the SLEEP button again to move to the next time increment Press the SLEEP button until you get to the desired time 30 60 90 120
14. and Polarities of Input Signals 38 Function menu 31 46 G Gain 26 Go back button 13 Gray level 33 Guide button 13 H HD select 37 HD RCVR button 14 HD Receiver Connecting 9 HD receiver 9 HD Receiver Mode 37 1080A 37 1080B 37 Info button 13 Input button 13 Input Go Back 7 Inserting batteries in the remote 15 Installation 6 42 Floor Stand 42 Speakers 42 Ventilation requirements 42 J Jacks 8 11 ACIN 8 External Speakers 8 50 External Control 8 Video in Audio in 8 L Language for the Menus 38 Laser Disc Player 10 M Macintosh computer connecting 43 Memory Mode 24 Menu button 14 Menu OK 7 Menu display position 31 Menu System 23 46 Mini D sub 15 Pin VGA Signal Compo sition 43 Monitor button 14 Mute 22 N Navigating the menus 22 Noise Reduction 27 Number buttons 14 O OK button 14 On Off button 14 On screen Menus 23 display position 31 Options menu 35 46 P Personal computer connecting 10 11 43 Picture Quality menu 24 46 Picture mode Bright 24 Memory 24 Normal 24 Preset 24 Soft 24 Picture position 30 31 PLE INVERSE 33 Power 22 Power cord 6 Power Saver 32 Power standby indicator 32 Programming the remote 15 Presets 24 R Reducing noise in the picture 27 Remote Control Automatic Code Search 16 Buttons 13 14 Codes 18 inserting batteries 15 Mute 22 Navigating the Menus 23 Programmable Codes 18 Programming the Remote 16 Resettin
15. black level and sharpness You can continue adjusting settings in the PICTURE QUALITY menu return to the main menu or exit the menu system To return to the main menu press the GO BACK button on the remote To exit the menu system press CLEAR 24 This is the PICTURE Quality menu with the PRESETS option highlighted PRESETS This is the PRESETS screen with SOFT as the current selection THE MENU SYSTEM ADJUSTING THE PICTURE SETTINGS IN MEMORY Mope In MEMORY mode you can set and save the following picture adjustments CONTRAST Changes the picture s contrast between light and dark BLACK LEVEL Makes the picture lighter or darker SHARPNESS Changes the picture s sharpness COLOR Changes color density video input only TINT Changes picture tint video input only COLOR TEMP Changes the color tone NOISE REDUCE noise reduction Removes extraneous information from the signal to make the picture clearer NOTE Only the contrast and brightness can be adjusted when a computer signal is used Once you have selected MEMORY mode you can adjust the picture settings For example to change the contrast setting 1 Use the A or V button to highlight the CONTRAST option Press the p gt button to select it The CONTRAST window appears Use lt q and p buttons to adjust the contrast NOTE if you don t push the lt q or p button within 5 seconds the current setting is accepted and th
16. internal heat build up Do not cover rear vents or install in a closed cabinet or shelves The unit is equipped with cooling fans If you install the unit in an enclosure be sure there is adequate space at the top of the unit to allow hot air to rise and escape If the monitor becomes too hot the overheat protector will be activated and the monitor will be turned off If this happens turn off the power to the monitor and un plug the power cord If the room where the monitor is installed is particularly hot move the monitor to a cooler location and wait for the monitor to cool for 60 minutes If the problem persists contact your Cinema Screen dealer for service 2 Do not use the power cord plug with extension cords or outlets unless all prongs can be completely inserted 3 Do not expose unit to water or moisture 4 Avoid damage to the power cord and do not attempt to modify the power cord 5 Unplug unit during electrical storms or if unit will not be used over a long period 6 Do not open the unit which has potentially dangerous high voltage components inside If the unit is damaged from opening the cabinet the warranty will be void Moreover there is a serious risk of electric shock 7 Do not attempt to service or repair the unit TCE is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the back cover Refer all service to authorized Cinema Screen Service Centers
17. is displayed 2 Use the A and V buttons to select the mode you want to change 3 When the desired mode is highlighted press the p gt button The selected mode screen will be displayed Use the arrow buttons to adjust the position of the picture NOTE If you don t push the an arrow button within 5 seconds the current setting is accepted and the previous screen reappears 4 When you ve adjusted to the desired setting press the GO BACK button on the remote to return to the SCREEN menu The V HEIGHT and H WIDTH options expand and contract the size of the picture to fill the screen For example if the picture is slightly wider than the screen you can use the H WIDTH option to shrink the picture horizontally Note These options are not available in STADIUM mode To adjust the screen size 1 Select the desired option from the screen menu and press the J gt button The selected mode window will be displayed 2 Usethe arrow buttons to adjust the size of the picture NOTE If you don t push an arrow button within 5 seconds the current setting is accepted and the previous screen reappears 3 When you ve adjusted to the desired setting press OK to select and return to the SCREEN menu Auro PICTURE The AUTO PICTURE function appears in the SCREEN menu only if you have a computer connected to the Cinema Screen display When this feature is turned on it automatically adjusts flickering and striped patterns in a computer i
18. menu system SELECTING THE LANGUAGE FOR THE Menus The menu display can be set to one of three lanuages English French or Spanish The default is English To change the default setting 1 From the main menu highlight and select the SETUP option The SETUP menu is displayed 2 Highlight the MENU LANGUAGE option The MENU LANGUAGE screen is displayed 3 Use the M button to scroll through the language choices The settings switch as follows ENGLISH FRANCAIS ESPANOL 4 When the desired language is highlighted press GO BACK to return to the SETUP menu You can continue making adjustments within the SETUP menu press GO BACK to return to the main menu or press CLEAR to exit the menu system SETTING THE VIDEO SIGNAL FORMAT The COLOR SYSTEM option is used to set the video signal format Different countries used different formats for video signals The AUTO option automatically detects the correct video signal and sets the correct format This setting should not be changed 38 This is the SETUP menu with the FREQUENCY option highlighted This is the FREQUENCY screen This is the MENU LANGUAGE screen with Spanish as the selected language THE MENU SYSTEM THe AUTOTUNING MENU AUTOTUNING THE COMPONENT BUTTONS ON THE COCRUNSFUNWESETUE REMOTE CONTROL T The AUTOTUNING feature lets you easily program the component buttons on the remote to operate the components hooked up to the Cinema
19. oe 2009 2014 2018 2054 2121 Gradiente 2026 2026 2009 Harley Davidson Harman Kardon Harwood 2061 Headquarter issiran aii 2011 Hitachi 2002 2055 2056 2057 2107 2111 2126 2122 HEQE iiic dien rneacier einen odes instant Replay JC Penney 2009 2010 2011 2013 2014 2021 2022 2055 2056 2058 2059 2060 2107 2118 2055 2056 2111 JVC 2009 2010 2011 2018 2058 2111 2123 Kenwood 2009 2010 2011 2016 2018 2058 2111 2123 KEH iau re eR EA em dd 2061 Kodak ecce iet 2014 2021 LIOVO eei quiete beg 2002 2026 Logik s 2061 LXI we 2014 Magnavox 2021 2022 2062 2063 2104 2108 2124 Ducem D 2013 Marantz 2009 2010 2011 2016 2018 2021 2058 2062 2064 MGN Technology secet 2013 Midland i2 eee rni ten ai na 2053 Minolta 2055 2056 2107 Mitsubishi 2029 2055 2056 2065 2066 2067 2069 2070 2071 2072 2073 2074 2106 2113 2123 Montgomery Ward ssssos 2075 2131 MOtOFOEA 1 osse eeepc 2021 2131 MTC 2002 2013 2026 Multitech 2002 2013 2016 2026 2053 2061 NEC uu 2009 2010 2011 2016 2018 2058 2064 2076 2078 2079 2111 2123 NiKKO ua cases EE 2014 Olympus Optimus Optonica Orion Panasonic 2021 2022 2109 2125 2126 2127 Pentax 2016 2055 2056 2107 2120 Pentex Research ess
20. option contains two features in one These features are level at 3 or 4 used principally for PC operation The PLE Peak Luminance Enhancement function sets the luminance level to a fixed mode to reduce the effects of phosphor aging The INVERSE function works in RGB mode only INVERSE inverts the video signal playing the image in a negative format PLE INVERSE has four options AUTO luminance level contrast is normal AUTO ON normal contrast with inverse activated LOCK dims picture to reduce phosphor aging LOCK ON dims picture to reduce phosphor aging with inverse activated The factory setting is AUTO Setting the PLE INVERSE option to LOCK dims the picture the contrast wiH be lower than normal To set the PLE level to LOCK This is the FUNCTION option with the 1 From the main menu highlight and select FUNCTION The PLE INVERSE option highlighted FUNCTION menu is displayed 2 Highlight the PLE INVERSE option Setting PLE INVERSE to LOCK is 3 Use the p gt button to select LOCK recommended if you are displaying 4 Press the lt q button to return to the FUNCTION menu options You stationary pictures can continue making adjustments within the FUNCTION menu return to the previous menu or press MENU or CLEAR to exit the menu system 33 THE MENU SYSTEM ADJUSTING FOR FLICKERING WITH Fitm MODE There is some amount of flickering that occurs in an image when it is transfered from film to video
21. AR to exit the menu system ADJUSTING THE POSITION or THE Menu Display The on screen menus can de displayed in different positions on the screen There are a total of nine possible positions shown in the grid on the right To adjust the position of the on screen menus 1 From the main menu highlight and select the FUNCTION option The FUNCTION menu is displayed 2 Highlight and select the MENU ADJUST option Use the p gt button to scroll through the menu positions As you press the p gt button the menu will move around to the different positions 3 When you have the menu in the desired position you can press the A or V arrow to select another option in the FUNCTION menu press GO BACK to return to the main menu or press CLEAR to exit the menu system peseecsesanmennscuasn Rmudaan naar uua umen Mam ma dad EE The number 2 position will display on screen menus in the top center of your screen 31 THE MENU SYSTEM SETTING THE POWER SAVER For COMPUTER IMAGES The POWER SAVER function can be used when the signal source to the monitor comes from a computer conforming to the VESA DPMS format This function automatically reduces the monitor s power consumption if no operation is performed for a certain amount of time POWER SAVER can be turned on or off If the computer s power isn t turned on or if the computer and selector tuner are not properly connected POWER SAVER is set to OFF For instructions on using th
22. DBY Inpur Go Back Input Go Back Switches the input in the following order r VIDEO1 VIDEO2 VIDEO3 CMPNT 14 RGB3 RGB2 RGB1 CMPNT2 Note You can set up CMPNT1 or RGB2 but not both When an on screen menu is being displayed returns you to the previous menu POWER STANDBY indicator When the power is on the light is green When the power is in Standby Mode the light is red ly Turns the monitor s power on and off SETUP AND CONNECTIONS Part NAMES AND FUNCTIONS Back VIEW 1 eT Se ros ea rs Ai oo ooo d 1 EXT SPEAKER L and R Connect speakers here 2 EXTERNAL CONTROL This terminai is used when the Cinema Screen monitor is controlled by external Q 2 3 equipment 4 REMOTE am ov Lore 3 REMOTE CONTROL This jack is for connecting a wired remote which is primarily for commercial applications The remote included with your monitor is wireless and doesn t require connection to the monitor 4 CONTROL LOCK When CONTROL LOCK is in the ON 8 position the buttons on the monitor s control panel don t function AC IN Connect the included power cord here RGB3 DVI 29pin Inputs a digital RGB signal RGB1 Connect HD receiver here BNC SELECT RGB2 inputs the analog RGB signal CMPNT2 Connect DVDs Laserdiscs etc here 9 VIDEO 01 2 3 Connect VCRs DVDs Laserdiscs etc here 10 AUDIO1 AUDIO2
23. E REMOTE There are two ways to program the remote control automatic code search and direct entry Usinc Automatic Cope SEARCH 1 16 Turn on the component you want the remote to operate VCR HD receiver etc Press and hold the component button that corresponds to the component you want the remote to operate VCR HD receiver etc While you hold down the component button press and hold ON OFF when the red light on the remote turns on release both buttons Press PLAY the red light on the remote starts flashing The remote is searching the first set of component codes there are several sets of codes If the component you want to operate doesn t turn off automatically after 5 seconds press PLAY again the red light starts flashing again as the remote searches through the next set of codes Continue pressing PLAY until the component turns off NOTE if the component doesn t turn off after you ve pressed the PLAY button 20 times the component can t be programmed Press REVERSE and wait 2 seconds Repeat this step until the component turns back on To finish press and hold the STOP button until the red light on the remote turns off ver ON OFF MONITOR DC DVD VCR2 AUX HDRCVR ALAA Component Buttons These are the buttons you program to operate another component SETUP AND CONNECTIONS Using Direct ENTRY 1 Turn on the component you want the remote to operate the red light on t
24. IMPORTANT TIPS CaniNG FOR YOUR CiNEMA ScREEN MONITOR TO AVOID DAMAGE AND PROLONG OPERATING LIFE 1 Useonly with 120V 50 60Hz AC power supply Continued operation at line voltages greater than 120 Volts AC will shorten the life of the unit and might cause a fire hazard 2 Handle the unit carefully when installing it Locate set away from heat excessive dust and direct sunlight 4 Protect the inside of the unit from liquids and small metal objects In case of accident unplug the unit and have it serviced by an authorized service center 5 Do not hit or scratch the panel surface as this causes flaws on the surface of the screen 6 For correct installation and mounting it is strongly recommended to use a trained authorized Cinema Screen dealer 7 Like ati phosphor based display devices Cinema Screen monitors can be susceptible to uneven phosphor aging under certain circumstances Certain operating conditions such as the continuous display of a static image over a prolonged period of time can result in uneven phosphor aging if proper precautions are not taken To protect your investment in this Cinema Screen monitor please adhere to the following guidelines and recommendations for minimizing the occurrence of uneven phosphor aging Always enable and use your computer s screen saver function during use with a computer input source Display a moving image whenever possible Always power down the monitor when yo
25. TING THE DisPLAv IN RGB3 INPur MODE If the picture is not stable in RGB3 mode use the RG ADJUST feature to adjust it 1 From the main menu highlight and select OPTIONS The OPTIONS menu is displayed 2 Highlight the RGB3 ADJUST option 3 Use the j gt button to select the desired adjustment 1 2 or 3 The choices scroll as follows pup crm 4 When the desired number is selected press the lt q button to return the the OPTIONS menu items You can continue making adjustments within the OPTIONS menu press GO BACK to return to the previous menu or press MENU or CLEAR to exit the menu system Note When AUTO PICTURE is on switch it off and back on again to return the display position to its original position This is the OPTIONS menu with the HD SELECT option highlighted This is the OPTIONS menu with the RBG3 ADI option highlighted 37 THE MENU SYSTEM THE SETUP MENU The SETUP menu controls the way your monitor communicates CONFIRMING THE FREQUENCIES AND POLARITIES OF INPUT SIGNALS The FREQUENCY function is used to confirm the frequencies and polarities of the signals coming from a computer To confirm frequencies and polarities 1 From the main menu highlight and select the SETUP option The SETUP menu is displayed 2 Highlight the FREQUENCY option and press OK 3 The FREQUENCY screen is displayed Press GO BACK to return to the INFORMATION menu or press CLEAR to exit the
26. TURE Noise is a term used to describe extraneous bits of information in the signal that affect the clearness of the picture You can use the Noise Reduction NOISE REDUCE setting if your reception is poor or when playing video tapes that have poor picture quality The NOISE REDUCE option has four settings including OFF The higher the setting the stronger the effect The settings switch as follows when the p gt button is pressed i OFF LOW MEDIUM HIGH 7 To change the noise reduction setting 1 From the PICTURE QUALITY menu highlight the NOISE REDUCE option and select it by pressing the p gt button The NOISE REDUCE SCREEN is displayed 2 Use the lt q and J gt buttons to select the desired noise reduction setting NOTE If you don t push the lt or p button within 5 seconds the current setting is accepted and the previous screen reappears 3 When the desired setting is displayed press OK to return to the PICTURE QUALITY menu You can continue adjusting picture settings return to the main menu or press CLEAR to exit the menu system This is the PICTURE QUALITY menu with the NOISE REDUCE noise reduction option highlighted This is the NOISE REDUCE noise reduction screen 21 THE MENU SYSTEM THe AUDIO Menu The AUDIO menu allows you to adjust the treble bass and left right balance of your external speakers BASS Changes the level of low frequency sound TREBLE
27. Z e m 9 m e a L Q Un Es 2 e ul Z a F SAFETY INFORMATION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE WARNING RISK OF ELECTRIC SHOCK REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates dangerous This symbol indicates A voltage inside the product that A important instructions presents a risk of electric shock or accompanying the product personal injury PRECAUTIONS Please read this manual carefully before using your Cinema Screen Monitor and keep the manual handy for future reference WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS ALL PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL INDUSTRY CANADA ComptiANce NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations DECLARATION OF CONFORMITY This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Product Cinema Screen Displ
28. ay Equipment Classification Class B Computer Peripheral Model PSP4200 FP4200 We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC rules Thomson Consumer Electronics Inc 10330 N Meridian St Indianapolis IN 46290 Phone 1 800 433 8974 FCC Information FCC Regulations state that unauthorized changes or modifications to this equipment may void the user s authority to operate it This equipment has been type tested and found to comply with the limits for a Class B Digital Device in accordance with the specifications in Part 15 of the FCC rules These rules are designed to provide reasonable protection against radio and television interference in a residential installation This equipment generates and can radiate radio frequency and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to the radio or television reception which you can determine by turning the equipment off and on try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna that is the antenna for the radio or television that is receiving the interference Change the position of the Cinema Screen display with respect to
29. button to toggle between RGB2 composite and CMPNT2 component 4 Once you ve selected the desired setting press the lt button to return to the OPTIONS menu items or press CLEAR to return to the main menu The factory defaults are as follows RGB1 AUDIOT VIDEO INPUTS AUDIO 2 COMPONENT INPUTS AUDIO3 If you use the reset option the settings will return to the factory default settings This is the OPTIONS menu with the AUDIO1 input option highlighted This is the OPTIONS menu with the BNC SELECT option highlighted 35 THE MENU SYSTEM SETTING A COMPUTER IMAGE TO THE Correct RGB SELECT MODE The RGB function allows you to select the correct viewing mode for the type of computer image you are displaying The RGB SELECT function has four modes RGB Use this mode for normal computer images VIDEO Use this mode to display video signal that has been converted to the RGB signal WIDE Use this mode to prevent an image that is inputted from 852 dot X 480 line signal with a vertical frequency of 31 72 KHz from being compressed horizontally DTV This mode is primarily used to optimize picture quality if you are using a generic brand DTV receiver which output signal at 480P progressive scan lines To change the RGB SELECT mode 1 From the main menu highlight and select the OPTIONS menu The OPTIONS menu is displayed 2 Highlight the RGB MODE option 3 Usethe p gt button to scroll t
30. correctly Adjust the picture from the SCREEN menu not centered image is too large or too small Is the screen size adjusted correctly Press the WIDE AUTO WIDE button on the remote control and adjust properly Picture is unstable Is the computer set at the correct resolution Set to the proper resolution Is the HD receiver set to the correct mode Set HD receiver to the correct mode page 29 45 REFERENCE THE CINEMA SCREEN Monitor MENU SYSTEM Main menu PICTURE QUALITY Main menu AUDIO Main menu SCREEN Main menu FUNCTION 46 Sub menu CONTRAST BLACK LEVEL SHARPNESS COLOR TINT PRESETS COLOR TEMP NOISE REDUCE Sub menu BASS TREBLE BALANCE Sub menu V POSITION H POSITION V HEIGHT H WIDTH AUTO PICTURE FINE PICTURE PICTURE ADJ Sub menu DISPLAY MENU ADJUST POWER SAVER GRAY LEVEL PLE INVERSE FILM MODE RESET Functions Adiusts the contrast Adjusts the brightness Adjusts the sharpness Adjusts the color density video input only Adjusts the picture tint video input only Sets the picture mode according to the video environment Adjusts the color temperature and white balance Reduces noise visible in image Functions Sets the bass Sets the treble Sets the left right balance Functions Adjusts the vertical picture position of the picture on the screen Adjusts the horizontal picture position of the picture on the screen Adjusts the vertical
31. ctor power cord safety metal fitting screw for safety metal fitting User s Manual UL approved UL 1950 CSA 950 DOC Canada requirements Regulations 44 Meets FCC class B requirements for home application 1 18 me 21 4 25 5 The features and specifications may be subject to change without notice DTV input signals supported on this system 10801 60 Hz 480P 60 Hz 4801 60 Hz 720P 60 Hz REFERENCE TROUBLESHOOTING Before requesting service check the adjustments operations etc Picture is disturbed Is a connected component set directly in front Leave some space between the display and Sound is noisy or at the side of the monitor connected components Remote control unit operates erroneously The remote control does not work Remote control batteries may be dead Replace both batteries with new ones Remote may be in wrong mode Press component button for desired component Monitor s power does not turn on when the Is the monitor s power cord plugged into a Plug the monitor s power cord into a power remote control s power button is pressed power outlet outlet Are all the monitor s indicators off Press the power button on the monitor to turn on the power Monitor does not operate when the remote Is the remote control pointed at the monitor Point the remote control at the moni
32. e Damage resulting from non approved installation methods PRopucr REGISTRATION Please complete and mail the Product Registration Card packed with your unit It will make it easier to contact you should it ever be necessary The return of the card is not required for warranty coverage How State LAW RELATES TO WARRANTY This warranty gives you specific legal rights and you also may have other rights that vary from state to state lr vou PURCHASED YOUR DISPLAY UNIT OUTSIDE THE UNITED STATES This warranty does not apply Contact your dealer for warranty information 49 CINEMA SCREEN DispLAY ACCESSORIES The Cinema Screen accessories listed below are available from your Cinema Screen Dealer See your dealer for prices CINEMA SCREEN ATTACHABLE SPEAKERS SPK42 CINEMA SCREEN DisPLAv STAND PLB1 50 Index Symbols 1080A 37 1080B 37 A Antenna button 13 arrow buttons 13 Audio input 35 Audio menu 28 46 Automatic Code Search 16 Auto picture 30 Autotuning 39 47 Aux button 14 B Balance 28 Bass 28 Batteries 9 15 Bias 26 BNC select 35 Black level 25 C CH CH button 13 Cinema button 13 Clear button 13 CMPNT button 13 Color system 38 Components Connecting 11 Computers Connecting 11 43 Contrast 25 Control Lock 8 D Default values resetting 34 46 DTV 36 DVD button 13 DVD Player 10 11 E External control 8 External Speakers 12 50 F Film mode 34 Frequencies
33. e computer s power management function see your computer s operating manual To turn the Cinema Screen s POWER SAVER function on or off 1 From the main menu highlight and select FUNCTION The FUNCTION menu is displayed 2 Highlight the POWER SAVER option 3 Use the p gt button to toggle the setting ON or OFF 4 You can continue making adjustments in the FUNCTION menu return to the previous menu by pressing the GO BACK button or press CLEAR to exit the menu system The POWER STANDBY indicator shows the status of the POWER SAVER function See below for status and description POWER STANDBY iNDICATOR POWER STANDBY indicator Power Saver Operating Status Description Horizontal and vertical synchronizing signals are present from the computer Not activated Standby Yellow Activated No horizontal synchronizing signals are present from the computer Activated Suspend No vertical synchronizing signals are present from the computer No horizontai and vertical synchronizing signals are present from the computer Activated 32 FUNCTION DISPLAY MENU ADJUST ER This is the FUNCTION menu with the POWER SAVER option highlighted Turning the Picture Back On Picture already on Use the keyboard or mouse The picture reappears immediately Use the keyboard or mouse The picture reappears but more slowly than when in standby mode Use the keyboard or mouse The picture reappears but mo
34. e previous screen reappears 2 Once the contrast is adjusted press OK or MENU The contrast is set and you are returned to the PICTURE QUALITY menu 3 Use the same procedure to adjust the black level and sharpness settings 4 When you are finished adjusting the picture settings press GO BACK to return to the main menu or press CLEAR to exit the menu system If the CONTROL NOT AVAILABLE message appears when you are trying to change the picture settings make sure the preset mode is set to MEMORY You can only change picture settings in MEMORY mode The other modes are pre set and can t be changed This is the PICTURE QUALITY menu with the PRESETS option highlighted This is the CONTRAST screen 25 THE MENU SYSTEM SETTING THE COLOR TEMPERATURE The color temperature setting controls how warm red or cool blue your picture is The COLOR TEMP option has 4 settings Normal Warm Pro lets you select settings individually Cool For regular viewing Normal Warm or Cool is recommended The PRO setting is generally used only for professional applications To change the COLOR TEMP setting 1 From the main menu highlight and select the PICTURE QUALITY menu 2 Use the arrow buttons on the remote to highlight the COLOR TEMP option Press the p gt button to select it The COLOR TEMP screen appears 3 Use the lt q and p buttons to select the desired COLOR TEMP setting The settings switch as follows N
35. easiis 10 Connecting a Personal Computer 10 Connecting Components to the Cinema Screen Monitor 11 Connecting External Speakers to the Cinema Screen Monitor 12 A Quick Tour of the Remote Control eee 13 Using Your Remote Control sessirnir 15 Inserting Batteries aoc oui e odisea ted da ord 15 Programming the Remote secession 15 Find Out If You Need to Program the Remote 15 How to Program the Remote ssssssseee 16 Using Automatic Code Search sss sess 16 Using Direct EDI o 6e Gre orca ticae Chat Loeb obtenida epos are kon 17 How To Use the Remote Control After You ve Programmed Ip desee ab adonde nine 17 Programmable Codes for the Remote Control acere 18 The Menu System oie tene entente pin tarioa nikawe Rune 21 Basic BeFalioBsa dei pexusporastutucappu deor dt queas kh IA tir aad 22 POST eus td eL Fond ct nues 22 NTIS Lu onec debet misil dete acta a 2c deu ood p nei dr Cd aaah Sd 22 MUTE iins A AAE an a TR EE 22 Navigating the MORES secre Y CO EV pia Eo EV 23 On Screen Menu Operation sssssse eene 23 The PICTURE QUALITY Menua cccccccccccccccccssssssssssssssssssssesseees 24 Setting the Picture Mode voco uet dll Ya 24 Adjusting the Picture Settings in MEMORY Mode 25 Setting the Color Temperature sssssssseee 26 Reducing Noise in the Picture sssssssseeeese 27 THE SOUND MENG Aoi bla revo ue DR E ro deu
36. ed at right side of the monitor when viewed from the front positive wire to RIGHT b Connect the right speaker negative wire to RIGHT c Connect the left speaker negative wire to LEFT d Connect the left speaker positive wire to LEFT Not included 12 SETUP AND CONNECTIONS A Quick Tour OF THE REMOTE CONTROL In alphabetical order ANTENNA In HD RCVR mode switches the HD receiver between antenna A and antenna B Arrows Use the arrows to navigate through the menu screens AUX auxiliary You can program this button to control any one of the following a cable box most GE RCA and PROSCAN audio components a laserdisc player a VCR or a satellite receiver Press this button to operate the component you ve programmed to work with the AUX button CH CH Changes channels on the HD receiver when the remote is in HD receiver mode When the Zoom mode is active zooms in CH or out CH CINEMA Press to select one of four screen sizes to suit the type of input you re watching NOTE When watching the HD receiver screen size is controlled through the HD receiver menu system CLEAR Clears on screen displays and returns you to normal viewing CMPNT Toggles between CMPNT1 and CMPNT2 inputs GO BACK In HD receiver mode returns you to the previous channel When in the menu system returns you to the previous menu GUIDE In HD receiver mode brings up the on screen program guide INFO Brings up chan
37. es 2018 Phiico 2021 2022 2062 2063 Philips i c t 2021 2062 2096 2124 die EE EAIA EM 2014 Pioneer 2010 2055 2080 2081 2123 Portland 2016 2017 2019 2110 PROSCAN 2000 2001 uisi pec 2061 Pulsar 2104 Quarter 2011 LEET E r APRE AE EA A EEA 2011 QUASAR eatha as ro eoe 2021 2022 2125 RCA 2000 2001 2003 2013 2021 2055 2056 2082 2083 2084 2085 2086 2087 2088 2089 2090 2091 2107 2115 2120 2125 Radio Shack Realistic 2002 2011 2013 2014 2021 2022 2023 2026 2029 2049 2050 2096 2131 Samsung 2005 2013 2015 2033 2053 2112 Sanky 2131 2104 Sansui 2010 2092 2111 2123 P X 2011 2013 2023 Scott 2012 2015 2025 2032 2035 2038 2065 2093 2116 Sears2011 2014 2021 2023 2048 2049 2050 2051 2055 2056 2107 2118 Sharp 2002 2017 2029 2094 2095 2096 2131 Shintom 2004 2056 2061 2098 Shout e tie et teal ricas 2013 Signature 2002 2131 Singer 2021 2061 2128 Sony Syivania 2002 2021 2022 2026 2062 2063 2065 2124 Symphonic sse 2002 2026 Tandy sess 2002 2011 TashiKO socie na rete ecd 2014 Tatung AAA EA E A A 2058 2111 TEAC Technics Teknika 2002 2026 2058 2085 2111 2021 2109 2002 2014 2021 2026 2100 2129 TM ceder Oi teeth ere ee 2013 2024 2047 Toshiba2015 2049 2051 2055 2065 2093 2116 TOE VISO
38. es of the picture Note If viewing with a 4 3 aspect ratio for long periods of time set side gray level at 3 or 4 FULL expands the picture in the horizontal direction only This option corrects the aspect ratio of images that have been compressed or squeezed STADIUM expands in both the horizontal and vertical directions but varies the amount of stretch depending on the picture the center of the picture is almost normal while the edges are considerably expanded This mode is intended for watching video with a 4 3 aspect ratio on a wide screen Note In stadium mode only the V position and H position are displayed You can t change the height and width To change the viewing size 1 Press the CINEMA button on the remote control 2 Thecurrent viewing size will be displayed Press the CINEMA button again to switch to the next size The size switches as follows FILL NORMAL FULL STADIUM Fil Normal Stadium 29 THE MENU SYSTEM ADJUSTING THE PICTURE POSITION AND SIZE The SCREEN menu lets you adjust the position and size of the picture The first two options V POSITION and H POSITION adjust the placement of the picture on the screen For example if the picture is too far to the left you can use the H POSITION to move it to the right To adjust the position of the picture on the screen 1 From the main menu highlight and select the SCREEN option The SCREEN menu
39. et from the monitor s remote control sensor and at a horizontal angle of within 30 The remote operates on line of sight so if there is anything blocking the path between the remote and the remote control sensor on the front of the monitor the remote may not work Don t expose the remote control sensor on the front of the monitor to direct sunlight or strong artificial light Don t get the remote control wet Avoid heat and humidity When not using the remote for a long period of time remove the batteries PROGRAMMING THE REMOTE The universal remote control that came with your Cinema Screen monitor is already programmed to operate most RCA GE and PROSCAN VCRs DVD players laserdisc players and satellite receivers This remote is also capable of operating many other brands of remote controllable electronic components but you must program it to do so Finn Our lr You NEED ro PROGRAM THE REMOTE To determine whether the universal remote needs to be programmed turn on one of your components such as a VCR Point the remote control at the component and press the component button for example the VCR button Now press the ON OFF button on the remote If the component doesn t turn off you need to program the remote control in order for it to operate that component Installing the batteries 30 App 7m 15 SETUP AND CONNECTIONS How TO PROGRAM TH
40. feces en eer pere e idt iiir Unitechi ooi deir rere recae deo Vector Research Victor i Video Concepts VideOSOTFIlc i inia ead treri ise parar red race esas Wards 2002 2013 2014 2015 2021 2023 2026 2029 2055 2056 2061 2096 2101 2102 2103 2107 2116 2131 2021 2026 2061 Yamaha 2009 2010 2011 2018 2058 2111 Zenith sss 2004 2098 2104 2119 2128 Caste Box ABC 5002 5003 5004 5005 5006 5007 5053 Antronix 5008 5009 Archer 5008 5009 5010 5011 Cabietenna ous ce operit ena ee ie Dye ensi 5008 Cabieview 5008 i r veieieshs 5011 CHIR GPE aori iddar derer kiai ERE Pans 5011 Colour Voice 5012 5013 COFDEODIOR spece restranse 5014 5015 COME h eai haia oa EE ENEE Eastern Garrard GC El Ctraniics e iseit eaaa ii 5009 Gemini Jerroid 5046 5053 MAQNAVON e 5025 MOMOTOR RR 5026 Movie Time oo coerce 5002 5027 5028 NSC 5002 5027 5028 Oak 5002 5018 5029 Panasonic 5048 5052 Paragol eo e pedo Head iade 5026 Philips 5011 5012 5013 5019 5025 5030 5031 5032 PIDE eniinn Tan 5033 5034 PSO oaen aea RS Tei 5026 RCA 5047 5049 5052 5009 5049 5022 5035 REGENCY oia cadi ren Anita 5017 Rembrandt eoo eren is 5003 RUFICO oa dates sas saad secbsiacsssged stash ne ri eR CI sab 5026 Samsung iicet aa pb de e 5014 5034 Scientific Atlan
41. g to default values 34 RGB Select 36 S Safety information 1 2 Safety metal fitting 6 Screen menu 29 46 51 Screen size Fill 29 Full 29 Normal 29 Stadium 29 Setting the Color Temperature 26 Setup menu 38 47 Sharpness 25 Sleep button 14 Sleep timer Cancelling 40 Checking 40 Setting 40 Speakers 12 50 Specifications 44 Stand using with Cinema Screen diaplay 42 50 T TREBLE 28 Troubleshooting 45 V VCR 10 VCR1 button 14 VCR2 button 14 Ventilation Requirements 42 Index Video button 14 Video 36 Viewing size selecting 29 Volume 15 22 Voi buttons 15 22 W Warranty 49 Wide 36 Z Zoom 7 Zoom in Zoom out buttons 14 52 Please do not send any products to the address listed in this manual or on the carton This will only add delays in service for your product d
42. he remote turns on Look up the brand and code number s for the component on the code list on the following pages Press and hold the component button that corresponds to the component you want the remote to operate VCR DVD etc Enter the code from the code list When you begin entering numbers the red light on the remote turns off When the last number is entered the red light turns back on If the incorrect code is entered the red light will flash Release the component button The red light on the remote turns off Press ON OFF to see if the component responds to the remote commands If it doesn t try pressing the component button and then ON OFF again If you get no response repeat these steps using the next code listed for your brand until the component responds to the remote commands How To Ust THE Remote CONTROL AFTER YOU VE PROGRAMMED IT Once the remote control has been programmed successfully you re ready to use it to operate other components 1 Press one of the video source buttons to select a component VIDEO or RGB to operate Press the component button MONITOR VCR DVD AUX or HD RCVR to use the Transport buttons REVERSE PLAY FORWARD STOP PAUSE and RECORD to operate the component Press ON OFF to turn the component on or off NOTE If you keep pressing buttons and nothing happens you may have the wrong video source or wrong component selected You must press the correct video sou
43. hrough the mode choices The settings switch as follows i RGB VIDEO WIDE en 4 When the desired mode is selected press the lt Q button to return the the OPTIONS menu items You can continue making adjustments within the OPTIONS menu press GO BACK to return to the previous menu or press CLEAR to exit the menu system 36 This is the OPTIONS menu with the RGB SELECT option highlighted THE MENU SYSTEM SETTING THE CINEMA SCREEN MONITOR TO THE CORRECT HD Receiver Move The HD SELECT function allows you to select the correct mode for the Cinema Screen monitor to work with your HD receiver The default setting is 1080A This is the correct setting for all RCA and PROSCAN HD receivers If you have another brand of HD receiver your picture may appear broken or off center If so you need to switch HD SELECT modes 1080A Use this option for RCA or PROSCAN HD receivers 1080B Use this option if you have any other brand of HD receiver To change the receiver mode 1 From the main menu highlight and select OPTIONS The OPTIONS menu is displayed 2 Highlight the HD SELECT option 3 Use the J gt button to select the desired mode 1080 A or 1080 B 4 When the desired number is selected press the lt Q button to return the the OPTIONS menu items You can continue making adjustments within the OPTIONS menu press GO BACK to return to the previous menu or press MENU or CLEAR to exit the menu system ADJUS
44. inema Screen monitor can be mounted on the wall using an optional wall mount or you can attach a floor stand also optional For more information on mounting your Cinema Screen Display see your Cinema Screen dealer If you choose to use the optional wall mount it can be attached to the Cinema Screen monitor in one of the following two ways While it is upright While it is laying with the screen face down If you choose this option lay the protective sheet that came wrapped around the monitor beneath the screen surface so it doesn t get scratched VENTILATION REQUIREMENTS FOR ENCLOSURE MOUNTING To allow heat to disperse leave space between surrounding objects as shown on the diagram below when installing 31mm 1 22 31mm 1 22 gt 1110mm 43 7 50mm 2 wa T E A m o e 748mm Y 50mm 2 VENTILATION SPACE AROUND UNIT 42 REFERENCE CONNECTING Your PC Or MACINTOSH COMPUTER Connecting your PC or Macintosh computer to your Cinema Screen monitor will enable you to display computer images on the monitor The Cinema Screen monitor supports the signals described on page 48 To connect to a PC Macintosh or compatible graphics adapter 1 Turn off the power to your monitor and computer 2 If your PC does not support XGA SVGAIVGA you will need to install an XGA SVGA VGA graphics board Consult your computer s owner s manual for your
45. ital RGB output Signal cable supplied To Mini D Sub 15 pin connector on the PlasmaSync 4210W RGB 3 DIGITAL RGB RGB 1 IBM VGA or Compatibles dm C A a Macintosh or Compatibles Monitor adapter for Macintosh LIMONO R VIDEO 1 VIDEO 2 I SAAS RAOT ER DER DER TERETE TTT VIDEO 3 ees E Ltonoy Et T VCR or Laser Disc Player R lt j SERVO ILESD IONIC L Ln DVD Player Ce Pe Cr Pr LIMONO SETUP AND CONNECTIONS Ei o o EI o o a Ire F je ZZ f CONNECTING EXTERNAL SPEAKERS TO THE CINEMA SCREEN MONITOR The Cinema Screen monitor doesn t have internal speakers so in order to get sound you must connect external speakers External speakers can reproduce sound from VIDEO or RGB signal sources External speakers may be connected directly to the SPEAKERS terminals or indirectly by connecting a stereo systern amplifier to the audio outputs CAUTION Unplug the monitor and all connected components before connecting external speakers Use only speakers with 6 to 8 ohm impedance and a power output rating of 7 watts or more To connect external speakers directly to the Cinema Screen monitor 1 Strip the ends of the speaker wires 2 Press down the tabs below the speaker terminals and insert the speaker wire and release the tab to secure the speaker wire connection a Connect the right speaker locat
46. mage If you want to adjust these manually 1 Select the AUTO PICTURE option from the SCREEN menu Press the p button to turn AUTO PICTURE off When AUTO PICTURE is turned off the FINE PICTURE and PICTURE ADJ options are displayed beneath it 2 Select an option and press the p gt button The screen for that option will be displayed Use the lt q and J gt buttons to adjust that option Press OK to return to the SCREEN menu 30 The SCREEN menu with the MODE option highlighted The AUTO PICTURE option only appears if you have a computer connected THE MENU SYSTEM THE FUNCTION MENU The FUNCTION menu contains options that control on screen displays other than the menu system and how the picture is displayed ON SCREEN DisPLAYs On screen displays different than the menu system appear by default to give you information about an option you have selected For example When you switch inputs the currently selected input name for example CMPNT1 is displayed on the screen To turn on screen displays off 1 From the main menu highlight and select the FUNCTION option The FUNCTION menu is displayed 2 Highlight and select the DISPLAY option Use the p gt button to toggle on screen displays on or off Note Turning the DISPLAY option off does not affect on screen menus Menus can t be turned off 3 You can continue setting options in the FUNCTION menu press GO BACK to return to the main menu or press CLE
47. nd of your RCA cable to the video output connector on the back of your VCR or laser disc player Connect the other end to the video input on the monitor 3 Use standard RCA cables to connect the audio from your VCR or laser disc player to AUDIO2 input jacks on the monitor if your VCR or laser disc player has this capability Be careful to keep your right and left channel connections correct for stereo sound 4 Turn on the Cinema Screen monitor and the VCR or laser disc player NOTE Refer to your VCR or laser disc player user s manual for more information about your equipment s video output requirements CONNECTING Your DVD PLAYER To connect your Cinema Screen monitor to a DVD player 1 Turn off the power to the monitor and DVD player 2 Use a standard video cables to connect your DVD player to the CMNT input on the monitor or use the DVD player s S Video output Use a standard S Video cable to connect to the S Video input on the Cinema Screen monitor 3 Turn on the monitor and the DVD player CONNECTING A PERSONAL COMPUTER If you have a computer with digital RGB output connect it to the RGB3 jack on the monitor For IBM VGA or compatible or Macintosh or compatible connect to the RGB1 jack on the monitor 10 RCA cables audio video cables are sold as a bundled set SETUP AND CONNECTIONS CONNECTING COMPONENTS TO THE CINEMA SCREEN MONITOR Personal computer with a dig
48. nel information INPUT Changes the video input MENU Brings up the on screen menu MONITOR Turns the power to the monitor on and puts the remote in Monitor mode so you are able to control the Cinema Screen display MUTE Reduces sound to an inaudible level Numbers Use the number keys to make numerical entries OK ZOOM When in Monitor mode press the MONITOR button and using on screen menus press OK to select a highlighted menu function When there are no on screen menus displayed press OK to bring up the zoom pointer Position pointer on the part of the screen you want to zoom on then use the CH buttons to zoom in out 100M in REVERSE PLAY FORWARD Ku RECORD STOP PAUSE 0 G3 uu CINEMA RGB CMPNT VIDEO 0000 L source universal 13 SETUP AND CONNECTIONS ON OFF Toggles power on and off for the components that you have programmed For example if you are in VCR mode turns VCR on and off REVERSE PLAY FORWARD STOP PAUSE RECORD transport keys Use with components programmed to work with your remote control VCR DVD player audio components DVD VCR2 AUX HDRCVR ALAA MUTE WHO ao RGB Depending on how you set up the Cinema Screen monitor toggles between RGB1 RGB2 and RGB3 Note You can set up CMPNT1 OR RGB2 but not both If CMPNTIT is set up RGB2 will not appear when you use the RGB bu
49. ng modes that can be selected depending on your viewing environment Each preset mode has the contrast brightness and sharpness adjusted for a specific viewing situation MEMORY This mode allows you to set and save your own picture adjustments SOFT Use this mode when watching your Cinema Screen in a dark room Soft mode provides a darker finer picture like the screen in movie theaters These settings are preset for you and can t be changed BRIGHT Use this mode when watching your Cinema Screen monitor in a bright room This mode provides a picture with distinct differences between light and dark areas These settings are preset for you and can t be changed NORMAL The factory default To change the picture mode 1 From the main menu select PICTURE QUALITY The PICTURE QUALITY Menu wil appear 2 Highlight the PRESETS option and press the p gt key on the remote to select it The PRESETS window appears 3 Use the M button on the remote to select the desired mode The mode switches as follows when the J gt button is pressed MEMORY SOFT BRIGHT ibus Note If you don t push the M button within 5 seconds the current selection is set and the previous screen reappears Once you ve selected the desired mode press OK or MENU The picture mode is now set and you are returned to the PICTURE QUALITY screen If you are using MEMORY mode you can manually adjust the picture settings contrast
50. nglish French or Spanish Sets the VIDEO format Keep this set to AUTO Functions Autotunes the HD RCVR button on the remote control to the input that your HD receiver is hooked up to Autotunes the SAT2 button on the remote control to the input that your satellite receiver is hooked up to Autotunes the VCR button on the remote control to the input that your VCR is hooked up to Autotunes the DVD button on the remote control to the input that your DVD player is hooked up to 4 REFERENCE SUPPORTED RESOLUTION When screen mode is NORMAL each signal is converted to 640 dot X 480 line signal except for 3 When screen mode is FULL each signal is converted to 853 dot X 480 line signal except for 2 Notes With Digital inputs some signals are not accepted The sync may not be disturbed when non standard signals other than the previously mentioned are input When connecting a composite sync signal use the HD terminal Tequency 2 frequency 82 ogni FULL 640 X 480 72 IBMPC ATcompablecompues 949X4807 600 310 ves YES 800 X 600 1024 X 768 1280x1024 600 640 YES Y 66 6 Sioni dns 1024x768 749 600 YES 1 Displays only 400 lines with screen center of the vertical orientation located at the center 2 Only when using a graphic accelerator board that is capable of displaying 848 X 480 3 Aspect ratio is 5 4 This signal is converted to a 600 X 480 line signal
51. ote Control 39 SLEEP TIMER zostera onrera aa EE a aT RER YIN DN GE 39 Setting the Sleep TIPRGE uiris rte Urea es Ever rae gave ao Aeg 39 Cancelling the Sleep Timer 39 Referente Mere T 41 Using the Cinema Screen monitor with the attached floor SLANG osi orae daiira Eaa ROO ER Ra Cpl eae 42 Attaching optional mounts or stand to the Cinema Sereen MORON aea e a are Denis pr rv LE ROME 42 Connecting Your PC Or Macintosh Computer 43 Mini D sub 15 Pin VGA Signal Composition 43 SbeciticaliObls vd asse QUod Gd e ated MU c od br com Be n MR sala 44 Troubleshooting nereseno esie dod con dia ea dede O 45 The Cinema Screen Monitor Menu System oo 46 Supported RESONATOR ooo re poneret tad ro rende e ei 48 RCA Cinema Screen Display Limited Warranty 49 Cinema Screen Accessories sssri snini 51 SETUP AND CONNECTIONS GETTING STARTED Welcome to the future The Cinema Screen monitor combines advanced technology with sophisticated design to create a sleek elegant monitor that fits unobtrusively into any environment while still making a lasting impression This first section contains all of the information you need to get your Cinema Screen monitor connected and set up The rest of the manual gives you guidance in using the functions of your monitor as weil as technical information troubleshooting and warranty information 1 SETUP AND CONNECTIONS 2 THE MENU SYSTEM y
52. otionis 28 Mie SCREEN MOTO nat bo pud erige isi EETA CLER HRS 29 Adjusting the Picture position sese 29 Ato d ICI EO ee bU E eee ae ea 29 Contents The EUUINGCTION MERE iioi edsbeun therrecatent kis De per Hid Sev ve eH 31 On Screen EISDIBVS inti isa re MET UHR NES Detroit 31 Adjusting the Position of the Menu Display ss 31 Setting the POWER SAVER for Computer Images 32 The POWER STANDBY Indicator ssss 32 Setting the Gray Level for the Sides of the Screen 33 Setting the Brightness Level with the PEESINVERSE Feature sich cat ee o eins 33 Adjusting for Flickering with Film Mode 34 Resetting to Default Values essen 34 The OPTIONS Mens societe HA tie e Pp pe oe ERR 35 Setting the Audio Inputs erret erre retis 35 Setting the BNC Connectors istoc den oat b eia aed 45 Setting a Computer Image to the Correct RGB Select MOUE toscana nisl Atami nana 36 Setting the Cinema Screen Monitor to the correct HD Receiver Mode 15 iirc 37 Adjusting the Display in RGB3 Input Mode 37 The SETUP Ment cio Dd We eap eonun Mara ep eite rn 38 Confirming the Frequencies and Polarities of Input Signals 38 Selecting the Language for the Menus ssssssssess 38 Setting the Video Signal Format ssssssssssseesee 38 The AUTOTUNING SE FUP Men 7 22 trn princ reti ces 39 Autotuning the Component Buttons on he Rem
53. rce and the component button that matches the component you want to operate 17 SETUP AND CONNECTIONS PROGRAMMABLE CODES FOR THE REMOTE CONTROL VCR Admifaluzx iid Nosti E Adventura Du m M 2002 2026 Akai 2003 2004 2005 2007 2008 2111 2112 2113 American High 00 ccc seneesneeceraeees 2021 D 2013 Audio Dynamics ccc 2009 2010 Audiovox ven 2014 Bell amp Howell sssssssssseseeeene 2011 Bea tfiatK 22a sie citer rere erii 2013 Broksonic 2012 2025 2014 Capehart CEIVED 21 eer ais d deese ees RP ES 2062 CGE acus er a 2027 2061 Citizen 2013 2014 2015 2016 2017 2018 2019 2027 COG 52r reo de Pl ate aids 2009 npa E Craig Curtis Mathes2000 2002 2009 2013 2016 2018 2021 2022 2024 2115 CyDOFDBX narn naher ett tht HH 2013 Daewoo2015 2017 2019 2025 2026 2027 2028 2110 DaytrOn aderidi cacsesacscbesassectesecasesedsouoaiaieas Dbx Dimensia Dynatech sssessee seres Etectrohome ssesssesee eene Electrophonic Emerson2002 2012 2014 2015 2021 2024 2025 2028 2029 2030 2032 2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2044 2045 2047 2065 2105 2113 2116 2117 2130 Fisher 2011 2023 2048 2049 2050 2051 2052 2118 Eujiz iacere eb pude n FUN AL esatera sikas died Garrard GE2000 2001 2013 2021 2022 2053 2115 2120 Goldstar
54. re slowly than when in either standby or suspend mode THE MENU SYSTEM SETTING THE GRAY LEVEL FOR THE SIDES OF THE SCREEN The GRAY LEVEL function allows you to set the gray level for the sides of FUNCTION the screen where nothing is displayed on the left and right sides of the o screen when it is set to 4 3 size The level can be adjusted from O to 15 The factory setting is 3 dark gray NOTE Repeated watching with the gray level set to black may effect the quality of your picture To reduce the effects of uneven phosphor aging set the gray level to 3 or 4 To adjust the gray level for the sides of the screen 1 From the main menu highlight and select FUNCTION The FUNCTION menu is displayed Highlight the GRAY LEVEL option Use the J gt button to scroll through the levels This is the FUNCTION menu with the GRAY LEVEL option highlighted 4 When the desired gray level is highlighted press the qd button to return to the FUNCTION menu options You can continue making adjustments within the FUNCTION menu press GO BACK to return NOTE Repeated watching with the to the previous menu or press CLEAR to exit the menu system gray level set to black may effect the quality of your picture To reduce the effects of uneven phosphor aging set SETTING THE BRIGHTNESS LEVEL WITH THE the gray level to 3 or 4 PLE INVERSE If viewing with a 4 3 aspect ratio for long periods of time set side gray The PLE INVERSE
55. size of the picure Adjusts the horizontal size of the picure When turned on automatically adjusts for flickering and striped patterns Adjusts for flickering in the picture Adjusts for striped patterns in the picture Functions Turns the on screen display on and off Adjusts the vertical and horizontal position of the menu display Sets the monitor for use as an energy saving display when used with a computer When viewing a picture with 4 3 aspect ratio sets the luminance of both sides of the picture Sets the brightness level to the minimum in VGA mode Normally set to AUTO When turned to AUTO selects the correct viewing format Resets ALL the settings to the factory default values 46 REFERENCE Main menu OPTION Main menu SETUP Main menu AUTOTUNING SETUP Sub menu AUDIO INPUT BNC SELECT RGB SELECT HD SELECT RGB3 ADJUST Sub menu FREQUENCY MENU LANGUAGE COLOR SYSTEM Sub menu HD RCVR BTN SAT2 BUTTON VCR1 BUTTON DVD BUTTON Functions Allocates audio connectors Sets BNC connectors to either composite or component video Sets the appropriate mode for the computer image RGB VGA signals VIDEO Moving picture WIDE WIDE VGA DTV Sets correct mode for your HD digital receiver 1080 A or 1080 B Adjusts the display position in RGB3 input Functions Confirms the frequency and synchronizing polarities of the signal currently being inputted Sets the language of the menus E
56. ta 5006 5036 5037 5038 Signal xen tiescat e eee 5014 5018 SETUP AND CONNECTIONS Signature eso deci rerit edis 5003 SATELLITE RECEIVER Aupio SE Mar esc ERIS 5014 SDEUCBE 2 odere piede rie ree rie 5052 Chapparal cesser 5056 5057 For RCA and Dimensia brands only Starcom 5007 5018 5053 Drake aiios ente licet eu 5058 5059 AM FM Stargate 5014 5018 c LOERT A RENAE E A E 5000 5001 AUX oo Starquest 5018 General Instuments 5060 5061 5062 Phono Tandy sisse 5040 Panasonic 5075 prm Primestar Jis 5076 Tape nan VEGO i ebd vem i rere dieere PROSCAN 5000 5001 RCA 5000 5001 Realistic 1 coiere peine 5063 SONY MU 5072 STS T risiede farei EEE EE T 5064 United Artists STS2 5065 United Cable STS3 5066 Universal 5008 5009 5010 5011 STS4 5067 VideOoWay orris iadair i 5044 Toshiba 5068 Viewstar seseses 5015 5025 5027 5040 Toshiba 5073 Zenith essere 5026 5050 5051 Unidos ooo eoe eee etre hottest Lpensie 5069 This page intentionally left blank THE MENU SYSTEM GETTING AROUND THE MENU SvsrEM There are several functions available for customizing the Cinema Screen monitor to suit your viewing environment The Cinema Screen monitor s on screen menu system makes controlling the functions of your monitor simple 1 SETUP AND CONNECTIONS 2 THE MENU SYSTEM
57. the radio or television equipment that is receiving the interference Move the Cinema Screen display away from the equipment receiving the interference Plug the Cinema Screen display into a different wall outlet so the receiver and the equipment are on different branch circuits If these measures do not eliminate interference please consult your dealer or an experienced radio television technician for additional suggestions Also the Federal Communications Commission has prepared a helpful booklet How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Please specify stock number 004 000 00345 4 when ordering copies WARNINGS AND SAFETY PRECAUTIONS The Cinema Screen monitor is designed and manufactured to provide long trouble free service No maintenance other than cleaning is required Use a soft dry cloth to clean the panel Never use solvents such as alcohol or thinner to clean the panel surface The Cinema Screen display panel consists of fine picture elements cells Although the Cinema Screen display panels are produced with more than 99 99 percent active cells there may be some cells that do not produce light or remain lit For operating safety and to avoid damage to the unit read carefully and observe the following instructions To avoid shock and fire hazards 1 Provide adequate space for ventilation to avoid
58. tor s control s buttons are pressed or is there an obstacle between the remote remote control sensor when pressing buttons control and the monitor or remove the obstacle Is direct sunlight or strong artificial light Eliminate the light by closing curtains pointing shining on the monitor s remote control the light in a different direction etc sensor Remote control batteries may be dead Replace both batteries with new ones No sound or picture is produced Is the monitor s power cord plugged into a Plug the monitor s power cord into a power power outlet outlet Is the source video connected and on Make sure source video VCR DVD DTC is connected and turned on Picture appears but no sound is produced Is the volume set at the minimum increase the volume is the mute mode set Press the remote control s mute button Are the speakers properly connected Connect the speakers properly Tint is poor or colors are weak Are the tint and colors properly adjusted Adjust the tint and color under PICTURE Return to factory reset Nothing appears on screen Is the computer s power turned on Turn on the computer s power Is a video source connected Connect video source to the monitor Is the power manager function in the Operate the computer move the mouse etc STANDBY or OFF mode Part of picture is cut off or picture is is the picture position adjusted
59. tton SLEEP Brings up the sleep timer which is used to turn the monitor off automatically after a set amount of time VCR1 VCR2 DVD HD RCVR MONITOR These are the component buttons used to put the remote control into the correct mode to operate that particular component The correct video source must first be selected VIDEO or RGB or Autotuning must be set up VOL X VOL v Adjusts the volume VIDEO Selects whatever component is hooked up to the video source inputs WHO Brings up personal viewer profiles for some components ZOOM IN When in zoom mode press the MONITOR button an then the OK button to access zoom mode enlarges the picture When in zoom mode use the arrow buttons to pan and scan the entire picture INPUT O REVERSE PLAY FORWARD debe RECORD STOP PAUSE O 0 D CINEMA RGB CMPNT VIDEO OQ000 L source ANTENNA ZOOM OUT When in zoom mode press the MONITOR button an then the OK button to access zoom mode decreases the size of the picture If picture is distorted zoom out to restore to normal universal 14 SETUP AND CONNECTIONS Usinc Your REMOTE CONTROL INSERTING BATTERIES 1 Remove the battery compartment cover from the remote control 2 insert batteries included as shown on the diagram inside the battery compartment 3 Replace the battery compartment cover Use your remote control from a distance of about 7m 23 fe
60. u are finished using it f viewing with a 4 3 aspect ratio for long periods of time set side gray level at 3 or 4 IF THE CINEMA SCREEN MONITOR IS IN LONG TERM USE OR CONTINUOUS OPERATION TAKE THE FOLLOWING MEASURES TO REDUCE THE LIKELIHOOD OF UNEVEN PHOSPHOR AGING Lower the BRIGHTNESS and CONTRAST levels as much as possible without impairing image readability Display an image with many colors and color gradations i e photographic or photo realistic images Create image content with minimal contrast between light and dark areas for example white characters on black backgrounds Use complementary or pastel color whenever possible Avoid displaying images with few colors and distinct sharply defined borders between colors Contents Safety Information 2 lt cccsvedsccssescidccasesiwacsecnseennsiecrasbsntsseeeese 1 Warnings and Safety Precautions ssssssssssseeee 2 IMPORTANT TIPS Caring for Your Cinema Screen Monitor 2 Getting Started siciaiicssinscintadiinaninnaiielninionmnin 5 Contents of ihe Package sc qa De uan cancels cde 6 Part Names and Functions Front VieW ecenin 7 Part Names and Functions Back View wo eee 8 Battery Installatioft o c Lar a a H ED eR ERE LN uda 9 Connecting an HD Receiver Lebe bte tace e ads 9 The Back ofthe HD Receiver ed neos Pat iaa t 9 Connecting Your VCR Or Laserdisc Player ees 10 Connecting Your DVD Player a sisisnicaccinesslieudioridstervecnsssorn

U S E R ` S M A N U A L

Contents

Download Pdf Manuals

Related Search

Related Contents