installation instructions pressure assist toilets
Contents
1. ATTENTION INSTALLER PLEASE LEAVE THESE INSTRUCTIONS WITH THE CONSUMER INSTALLATION INSTRUCTIONS PRESSURE ASSIST TOILETS Thank you for selecting Crane Plumbing Products To ensure this product installs properly please read these instructions carefully before you begin Be sure your installation conforms to local codes CRANE PLUMBING The Clear Choice REMOVE OLD TOILET Close toilet supply valve and flush the toilet Sponge any remaining water from the bowl Discon nect and remove supply line If replacing valve first shut off the main water supply Remove mounting bolts and lift bowl off toilet flange Plug waste opening to prevent sewer gas from escaping Clean away old wax etc from installation area Before Beginning The toilet is in two cartons One contains the bowl and the other has the tank cover and assorted parts Assuming that your bathroom has a four inch drain with a slotted toilet flange and cold water supply line in place to com plete your installation you will need the following items not supplied two closet bolts wax ring or bowl gasket supply pipe and shut off valve toilet stop A Word of Caution The new toilet is made of fine china like the best quality tableware It is ruggedly constructed however extra care should be exercised during installation when rough handling and the danger of dropped tools threaten to chip or crack it Water Supply If your cold water line is through the wall install an Angle Stop If i2. Exclusions CRANE PLUMBING L L C PRODUCTS SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING COSTS OF INSTALLATION OR WATER DAMAGE OR FOR DAMAGES RESULTING FROM ABUSE OR MISUSE OR FROM FAILURE TO INSTALL OR MAINTAIN THIS PLUMBING PRODUCT INACCORDANCE WITH THE WRITTEN INSTRUCTIONS FURNISHED BY CRANE PLUMBING L L C PRODUCTS USE OF CLEANING PRODUCTS CONTAINING CALCIUM HYPO CHLORITE CHLORINE SHALL CONSTITUTE IMPROPER MAINTE NANCE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO THE CONSUMER THE ONLY WARRANTY MADE BY CRANE PLUMBING L L C PRODUCTS IS SET FORTH ABOVE AND ALL IMPLIED WARRANTIES WHICH MIGHT ARISE INCLUDING THE IMPLIED WARRAN TIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED Warranty Service In order to obtain warranty service or adjustments contact the builder dealer or plumber from whom the product was purchased or the Cus tomer Service Department U S A customers contact Crane Plumbing L L C Products 41 Cairns Road Mansfield OH 44903 8992 Phone 800 546 5476 Fax 419 525 3169 CANADIAN customers contact Crane Plumbing Canada Corp 15 Crane Ave P O Box 337 Stratford ON NSA 6T3 Phone 800 463 2726 Fax 800 845 7158 In obtaining warranty service all transportation shipping and freight charges connected with transporting any part of this plumbing product must be prepaid by the co
3. arts may be obtained by contacting U S A Customers Contact Crane Plumbing LLC 41 Cairns Road Mansfield Ohio 44903 8992 Phone 800 546 5476 Fax 419 525 3169 email customerservice craneplumbing com CANADIAN Customers Contact Crane Plumbing Canada Corp 15 Crane Ave P O Box 337 Stratford ON N5A 6T3 Phone 800 463 2726 Fax 800 845 7158 email sales craneplumbing ca 10 Care and Cleaning of Vitreous China Your new toilet is made of stain acid and abrasion resistant vitreous china But like all fine finishes the china requires reasonable care For day to day cleaning wash with warm water a soft cloth and a mild detergent such as Handy Andy Mr Clean or Lestoil On stubborn stains use one of the powdered detergents such as Spic amp Span on a damp sponge or scouring pad of nylon saran or polyethylene Never use abrasive scouring powders cleansers or pads as they tend to create microgrooves that dull the finish and allow dirt to work into the surface Use of tank cleaning products containing calcium hypo chlorite chlorine or any other reactive chemical shall constitute improper maintenance WINTERIZING VITREOUS CHINA WATER CLOSETS ALL WATER MUST BE REMOVED FROM THE TANK AND BOWL Prior to winterizing the bowl please refer to the pressure vessel manual pro vided with the tank for winterizing instructions An anti freeze solution must be poured into the bowl through the tank flush valve opening in
4. lts project through the bowl mounting holes Install the washers with This Side Up toward you and thread on nuts Tighten the nuts alternating from side to side DO NOT OVERTIGHTEN VITRE OUS CHINA EASILY CHIPS AND CRACKS Pour water into the bowl to prevent the escape of sewer gas 2c Floor mounted back outlet bowls must be fastened to the floor with Lag Screws Supplied by others Slip the plastic washer marked side up onto the lag screw and screw into pre drilled pilot holes The tank should be inverted on the floor after removing the lid and parts bag Open the plastic envelope and place the large doughnut shaped washer snugly on the threaded tank outlet Invert the tank and place it on the bowl so that the large washer fits evenly into the bowl water inlet opening Make sure tank is centered and properly sealed Place the rub ber washer on the bolts and insert the bolts downward through the bolt holes Position the metal washer on each bolt With tank parallel to wall alternately finger tighten nuts Using a Wrench alternately turn the nuts until the tank is in contact with the bowl piers CAUTION Do Not Overtighten to avoid cracking china 4 Water Inlet Vasher gt Coupling Flexible a Nut Supply Valve Nut Fl sej F _ Compression F Ez ollar Valve Trim Piste Connect the cold water line to the tank with your straight or angle stop Place the washe
5. nsumer It is the responsibility of the consumer to establish the warranty period by verifying the original purchase date A bill of sale cancelled check or some other appropriate payment record may be kept for this purpose This warranty gives you specific legal rights You may also have other rights which vary from state to state Please enter the model number and date of purchase in the space provided BOWL MODEL TANK MODEL DATE OF PURCHASE Spec 2058 Rev 1 08 Crane Plumbing LLC 41 Cairns Road Mansfield Ohio 44903
6. r then the plastic nut on the tank end of the connecting pipe and bend the pipe to fit into the inlet hole on the wa ter regulator Tighten all coupling nuts securely DO NOT USE PLUMBERS PUTTY 5 Adjusting Tank Filling Time The tank pressure vessel has been designed and factory adjusted to pro vide a consistent safe trap seal and proper water depth in the bowl after each flush Refill adjustments are not possible or necessary The refill has been engineered and pre set All moving parts are inside the pressure vessel Rarely does a vessel malfunc tion If technical assistance is needed please call the 800 telephone num ber listed on the pressure vessel Place cover on tank Place the plastic bolt covers firmly in place Install the seat in accordance to the manufactur ers instructions NOTE Check all connections for several days to detect any leaks which may develop If they do tighten all connections per instructions Crane Plumbing LLC is not respon sible for leaking water connections Also after several days remove the bolt caps from the bowl and tighten the nuts snugly REPLACEMENT PARTS Please keep this manual for future reference Re tain product invoice in case warranty service be comes necessary Record the Model Number of the toilet in this booklet This will assist when or dering replacement parts or in seeking technical assistance Technical Assistance or Replacement P
7. side the tank to insure mixing with any water that may remain in the distribution area under the tank Continue to pour anti freeze solution until the level of solution in the toilet bowl stops increasing There must be liquid in the bowl at all times to prevent sewer gas from coming through the toilet NOTE It is recommended that RV Anti freeze be used Flush N TANK Control N COVER Valve PRESSURE VESSEL COMPLETE Limited Lifetime Warranty on China Limited One Year Warranty on Parts 10 Year Warranty on Pressure Vessel See Manufacturers Owners Manual Subject to the Exclusions set forth below Crane Plumbing L L C promises to the consumer to repair or at the option of Crane Plumbing L L C to replace any part of this plumbing product made from vitreous china which proves to be defective in workmanship or materi als under normal use and any other supplied part of this product under normal use for one year from the date of purchase All costs of removal transportation and reinstallation to obtain warranty service shall be paid by the consumer During the warranty period for china and one year period for parts Crane Plumbing L L C will provide subject to the Exclusions section set forth below all parts free of charge necessary to correct such defects if this plumbing product has been installed and maintained in accordance with written instruc tions furnished by Crane Plumbing L L C with this plumbing product
8. t is through the floor install a Straight Stop Installing the Toilet Bowl and Tank 2a j 1 Clean the immediate floor area thoroughly Insert new toilet bolts in the slotted flange bolt heads down The toilet bowl should be placed upside down on soft material to prevent scratching Place the slightly warmed wax ring in the circular recess in the base of the bowl NOTE It is recommended that a wax setting ring with flange be used Unplug floor waste opening Gently place the bowl right side up in posi tion with the toilet mounting bolts pro truding through the holes in the china base Press down with a slight twist ing motion on the top center with your full weight Make sure the bowl is as level as possible If needed you can use wedges under the bowl to help leveling Put the washers Marked This Side Up and nuts on the bolts Tighten them evenly and snugly DO NOT OVERTIGHTEN NUTS AS VITREOUS CHINA EASILY CHIPS AND CRACKS Pour water into the bowl to prevent the escape of sewer Rim of Bow a Mounting Surface P weopiene jy Seal If the toilet you are installing is a Back or wall outlet unit a closet flange must be installed in the wall 4 above the floor The flange must be perpendicular to the floor and aligned so the bowl mounting bolts will be parallel to the floor To in stall unplug the waste outlet and slide the bowl toward the closet flange so the bo
Download Pdf Manuals
Related Search