BM PRO - 19 Henderson Road, Knoxfield 3180, Victoria
Contents
1. EEE APP SET UP The BatteryCheck app is intended to configure the BatteryCheck device and display current battery information The Set Up screen will provide the following settable options Label Description Default Value Battery Volts A number in the range 9 0V to 13 0V 12V Battery 10 0V Warning A number in the range 18 0V to 26 0V 24V Battery 20 0V Audible Alarm Plays an alarm tune if the battery voltage is equal to No or less than the warning level above Vibrate Alarm Vibrates if the battery voltage is equal to or less than No the warning level above Visual Alarm The battery icon on the home screen flashes red ifthe Yes battery voltage is equal to or less than the warning level above BatteryCheck The alarm contacts on BatteryCheck will close if the No Relay battery voltage is equal to or less than the warning level above Please note warning notifications will only activate when users are in the BatteryCheck app and within Bluetooth range BATTERY CAPACITY SET UP AND WIRING This refers to the actual capacity of the battery in amp hours When a new battery is fitted set this to the nominal battery capacity as marked on the battery doing this will assist the software in determining actual capacity As BatteryCheck learns the battery capacity it will automatically update this parameter Following initial installation the battery capacity will appear as 50 Over time BatteryCheck will be able to read the battery state of2. Allow The Set Up screen will then appear Simply update the battery configurations according to the battery installed and click Save Refer to App Set Up section of this manual mm FOR ANDROID 8 Once BatteryCheck app is installed on your phone select the icon to start the app Following the splash screen appearing the Home screen will appear 9 Select the Set Up tab at the top of the app A pop up selection should appear then choose New Connection 10 Select your BatteryCheck device from the list provided If more than one device appears identify your device according to its serial number then click the Connect button If prompted enter your unique Bluetooth PIN which can be found on the serial number label on the back of BatteryCheck 11 Once connection has been established the Settings screen will appear Update the battery configurations according to the battery installed and click Save Refer to App Set Up section of this manual FOR iOS AND ANDROID 12 This should bring you back to the S 40 Home screen If you click the battery ren icon the Dashboard tab should appear indicating current charge or discharge voltage state of charge and battery state of health 13 When BatteryCheck has paired with the app the BatteryCheck unit light will turn blue and the electrical cord icon at the top right of the app will turn green OO C
3. charge and health and present an accurate indication of battery capacity Important Please remember that in order to keep track of battery capacity BatteryCheck device must measure all current in and out of the battery This is achieved by connecting BatteryCheck between the battery negative terminal and all negative connections This means that all new connections must be wired to the end of BatteryCheck that is not connected to the terminal Positive connections are simply wired as normal e g to the positive terminal of the battery Ne oy OLE BATTERYCHECK SPECIFICATIONS Specification Voltage Measurement Range Voltage Measurement Resolution Current Measurement Range Current Measurement Resolution Temperature Measurement Range Temperature Measurement Resolution Monitored Battery Capacity Visual and Audible Alarms General Specification Input Voltage Current Consumption Quiescent Current Drain Operating Temperature Humidity Altitude MTBF Dimensions Weight Installation IP Rating 8V to 30V 100mV or 0 1V 100A 100mA or 0 1A 20 C to 70 C Battery Terminal 1 C 7Ah to 800Ah Low Voltage user settable level Low State of Charge user settable level 8V to 30V 0 1 A peak lt 10mA 20 C to 70 C Operating lt 85 RH non condensing Non operating lt 95 RH non condensing Operating 2000 m Non operating 15000 m gt 50000 hours at 40 C 140 mm x 65 mm x 20 mm App
4. required for every application it simply depends on your battery type v gt Foam base supports SECURITY Each BatteryCheck is assigned a unique serial ID consisting of 11 alohanumeric characters A unique Bluetooth PIN is also supplied with your BatteryCheck and cannot be changed This PIN is located on the back of the device and is used to access BatteryCheck app We recommend noting down your unique Bluetooth PIN in a safe place If for some reason you do lose this number please send an email to warranty teambmpro com for further details BATTERYCHECK APP BatteryCheck app is compatible with Apple and Android mobile phones mm HARDWARE MOUNTING AND INSTALLATION NAME AND FUNCTION OF PARTS 1 Negative Battery Terminal Connection 2 New Negative Terminal Connection connects to load 3 Positive Flying Lead and Temperature Sensor MOUNTING BatteryCheck has a terminal at each end using these two terminals the device is wired in series with the negative terminal of the battery being monitored A separate lead provides connection to the positive terminal of the battery to power the unit measure the battery voltage and to assess the temperature and overall health of the battery Please ensure that all loads connected to batteries are disconnected when installing BatteryCheck to avoid battery sparks from occurring during this process INSTALLATION 1 Practice standard safety precautions and r
5. BM BY SETEC 48 gt BATTERY USER MANUAL BM PRO 19 Henderson Road Knoxfield 3180 Victoria Australia 61 3 9763 0962 61 3 9763 8789 sales teambmpro com www teambmpro com O EE CONTENTS Introduction 02 Safety Precautions 02 About BatteryCheck 02 Accessories 03 Security 03 BatteryCheck App 03 Hardware Mounting and Installation 04 Names and Functions of Parts 04 Mounting 04 Installation 04 App Set Up O7 Battery Capacity Set Up and Wiring OF BatteryCheck Specifications 08 Warranty Terms and Conditions 09 Copyright Setec 2014 Disclaimer Setec makes no claim as to the accuracy or suitability of the information contained in this manual Setec accepts no liability for any loss or damage which may occur as a result of improper or unsafe use of its products eS o LE INTRODUCTION SAFETY PRECAUTIONS Please read the Safety Precautions carefully prior to installing BatteryCheck Be sure to observe all precautions without fail Failure to observe these instructions properly may result in property damage or personal A CAUTION injury which may be serious depending on the circumstances Refer to the installation section before operating Correct installation is the most critical factor in ensuring safe use of BatteryCheck If every consideration of these instructions has been satisfied BatteryCheck will be safe to operate Ensure that cab
6. emove all connections to the battery 2 Connect Qto the battery negative terminal using the connector provided 3 Connect all of the negative loads or connections to 2 onBatteryCheck device 4 Connect the positive flying lead to the battery positive terminal o O E 10 11 Check that BatteryCheck unit light located in the battery icon logo flashes green indicating correct electrical connection Visit Bluetooth settings on your mobile device and ensure that this function is turned on Consult your phone s documentation regarding Bluetooth configuration if required Download app via Google Play or App Store Simply type BM PRO BatteryCheck into Google Play OR BatteryCheck into App Store search field to locate the correct application Select install and open FOR iOS Once BatteryCheck app is installed on your phone visit the iPhone settings screen Confirm the Bluetooth link is enabled By clicking the Bluetooth icon inside the Settings menu a list of devices within range should appear If more than one device appears identify your device according to its serial number then select it If prompted enter your unique Bluetooth PIN which can be found on the serial number label on the back of the BatteryCheck Step 10 Once connection has been established a pop up message should appear asking you to approve BatteryCheck app to connect to the device Click
7. le connections have the correct polarity and are protected against accidental short circuit Do not allow water or other liquids to enter the installation area ABOUT BATTERYCHECK BatteryCheck is a simple retrofittable device with an internal shunt that connects to a range of standard deep cycle batteries and communicates wirelessly with smart phones BatteryCheck provides real time battery management data that allows users to effectively monitor remaining battery energy via a simple to use app This device is suitable for recreational vehicle and marine deep cycle battery use up to 80 amps maximum charge or discharge BatteryCheck is not suitable to be used with engine cranking applications of any type and was not designed for under vehicle bonnet use BatteryCheck is connected to a 12 or 24 volt V deep cycle lead acid battery and monitors various parameters The device uses a Bluetooth signal via an app to allow access to these parameters OO O E Parameters monitored are gt Battery Voltage gt Battery Charge Discharge Current gt Battery Temperature Estimated State of Charge SoC gt Estimated State of Health SoH gt Estimated Discharge Time Remaining ACCESSORIES The following accessories are provided with BatteryCheck device gt 1x brass battery post gt 1x brass battery post connector Please note the connector post and supports are not
8. nal instructions supplied with the product 4 Setec may seek reimbursement for any costs incurred by them when a product is found to be in proper working order or damaged as a result of one or more of the warranty exclusions mentioned in point three of this statement 5 To enquire or make a claim under this warranty please follow these steps a Prior to returning product please contact Setec on 61 3 9763 0962 or warranty teambmpro com to obtain a Return Material Authorisation RMA number b Package and send the product directly to BM PRO by Setec Warranty Department 19 Henderson Road Knoxfield VIC 3180 Australia Please mark RMA details on the outside of the packaging c Please ensure the package also includes a copy of the proof of purchase a detailed description of the fault and your contact details including phone number and return address 6 Setec will not be liable for any costs charges or expenses incurred in the process of returning a product in order to initiate a warranty claim en og gt Water and waste tank monitoring including pump on off switch gt Battery monitoring displays remaining time left in battery volts and amps charge discharge status and remaining capacity state of charge www teambmpro com BMPRO SETEC DRIFTER gt Large LCD screen gt Low voltage warning gt Clock and temperature gauge gt USB charging port gt Battery isolating switch You
9. rox Approx 1 kg boxed with accessories Mounted on battery IP 65 OO C O _ E WARRANTY TERMS AND CONDITIONS Registering your BM PRO by Setec product is an important step to ensure that you receive all of the benefits you are entitled to Please visit https teambmpro com warranty to complete the online registration form for your new product today This registration is for original owners of BM PRO by Setec products only 1 BM PRO by Setec goods come with guarantees that cannot be excluded under Australian Consumer Law You are entitled to a replacement or refund for major failure and for compensation for any reasonably foreseeable loss or damage You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure 2 Setec as the manufacturer of BM PRO goods warrants products against defects for a period of two years commencing from the original date of purchase Proof of purchase is required before you can make a claim under this warranty 3 This warranty does not extend to product failures or defects caused by or associated with but not limited to failure to install or maintain correctly unsuitable physical or operating environment accident acts of God hazard misuse unauthorised repair modification or alteration natural disaster corrosive environment insect or vermin infestation and failure to comply with any additio
Download Pdf Manuals
Related Search