User Manual
Contents
1. Wall mounting work should be performed by a construction specialist Improper work may result in death or personal injury due to the product falling during operation Always use the specified mounting unit Improper assembly may cause the product to fall over There is risk of personal injury if the product falls over Completely tighten the screws of all individual parts Install this product on a flat wall Installing this product on an uneven wall such as bumpy or curved surfaces may cause the product to operate improperly or fall over resulting in personal injury or product malfunction Do not place in a location with flammable or corrosive gas Placing this product in a location where there is flammable or corrosive gas may result in fire or damage to this product There is a particular danger of explosion in the case of flammable gas Do not place in a location with flammable or corrosive gas N CAUTIONS Do not touch internally mounted parts Directly toughing internally mounted parts inside this product may result in personal injury or damage to this product Do not place in locations subject to excess moisture dust smoke or steam Placement in a location such as next to a kitchen or a humidifier may result in fire or damage to this product Do not use this product near water If water somehow gets inside this product immediately disconnect the USB cable and contact a support center Continu2. referred to as StarBoard This User s Guide has been created for people who already have a working knowledge of personal computers henceforth referred to as PC Please make sure that you understand the contents of this User s Guide and use the software correctly We hope that you make the most of this product 3 English StarBoard FX 79E1 89WE1 Safe Handlin Safe Handling Markings and Symbols Various markings and symbols are used in this User s Guide and on this product to ensure the safe and correct use of this product and to prevent personal injury and property damage These symbols and their meanings are as explained below Understand the information well before reading the body of the User s Guide This 1s a Safety Warning symbol This symbol will appear to raise the attention of the user to existing risks that may cause harm to people To avoid any chances of injuries or possibly death DO NOT IGNORE the safety instructions that follow this symbol ZN WARNINGS This warning will appear where there exists a risk of death or fatal injuries CAUTIONS This warning will appear where there exists a risk of moderate or light injuries NOTICE This warning will appear where there exists a risk of damage to property A This symbol draws attention to cautions including warnings This symbol indicates something prohibited This symbol indicates something that must be done 4 Englis
3. 2 4 of this User s Guide StarBoard Software files may bejUninstall the StarBoard Software and broken or installation may not bejthen re install it complete correctly JFor details on installing StarBoard Software see the StarBoard Software Installation Guide Other than the above Contact a support center nstable reaching the board surface or LED cover cover The controller must be reset and Disconnect the USB cable and the system restarted reconnect it If this does not solve the problem restart the PC In case that USB cable extended Ser E aa as bellow it may result in extend USB cable use self powered unstable of product working USB hub USB extension cable Bus powered USB hub JUSB extender of PCs with only one USB host controller 3 1 English StarBoard FX 79E1 89WE1 Appendix Input Related Problems What to check What to do The input position does not Has position alignment Perform proper position alignment match been performed properly Other than the above Contact a support center The position cannot beHave the StarBoard and Adjust the position of the StarBoard aligned properly projector been placed in theland the projector If undue correction proper orientation 1s performed 1t may not be possible to lalign the position properly Is the PC screen being Make sure the PC screen projection 1s projected inside the contained within the StarBoard s input StarBoard s input area area For det
4. handling and precautions mentioned in this user s guide In the event of failure or damage resulting from abnormal voltages pollution or other natural disasters e g fire earthquake and lightning In the event of a malfunction in this product caused by the connection to this product of equipment other than the equipment specified by our company In the event that there is no abnormality in this product but a defect in a part other than this product was detected or remedied In the event of ordinary wear and tear wear deterioration etc of consumables even during normal use 3 5 English StarBoard FX 79E1 89WE1 Appendix 5 If this product malfunctions review the contents of this user s guide If the problems remain irreparable contact the dealer The dealer will determine whether or not the product must be repaired so please contact them If the customer sends the product to our company without RMA Return Merchandise Authorisation number 1t might not be covered by warranty 6 As arule the customer is responsible for shipping charges required to send all or part of the product for repair etc Our company will assume responsibility for the return shipping to the customer 7 This warranty does not cover labour fees for repair associated equipment assembly or disassembly 8 Incidental damage caused by the failure of this product e g loss of profit that should have resulted from the use of this product i
5. people for this work Failure to comply may cause the board to fall resulting in personal injury or may cause damage to this product due to shock of impact Use the screws to install the wall mounting bracket on the wall Use 4 6 mm diameter screws 5 8 fea m Pal a a E o E IZ 12 z g IZ 2 Z jz z 2 gt 9 a a B B 1 9 English StarBoard FX 79E1 89WET1 Introduction 1 4 2 Stand Setup Method Reconfirm that all the parts are present before assembling and setting up the stand option N WARNINGS Tighten the screws securely Failure to comply may cause the stand to collapse resulting in personal injury or may cause damage to this product due to shock of impact from the board falling N CAUTION This work should be performed by at least two people The board might fall and cause injury or 1ts impact might cause damage 1 Assemble the stand FX 79E1 89WEl is available with the stand Follow the diagram below to install the board on the stand The numbers in the diagram correspond to the numbers in the parts tables on pages and 1 3 of this User s Guide Fasten with a Phillips screwdriver Align both feet with the longer side facing forward Fasten with an Allen wrench 1 10 English StarBoard FX 79E1 89WE7 Introduction 2 Adjust the height Follow the diagram below to install the stay The numbers in the diagram cor
6. the presentations You can also write on video images For Windows Characters or images can be written onto captured video image displays This makes it easy to use video materials in lessons or presentations 1 1 English StarBoard FX 79E1 89WE7 1 2 Parts Check Introduction After unpacking make sure that all the following parts are present 1 2 1 StarBoard 1 Parts USB Cable 5m Stylus pen Warranty Sheet 1 A E 4 5 6 Pa 8 9 1 2 1 5 1 i StarBoard Software Startup Guide StarBoard FX 79E1 89WE1 Startup Guide English StarBoard FX 79E1 89WET1 Introduction 1 2 2 Stand option 1 Parts Stand crossbar 3 Stand foot with casters 4 _ Board receiving bracket left hand version 1 5 _ Board receiving bracket right hand version 1 6 Boardfixing bracket 2 1 _ Hex socket head cap screw with collar 8 9 Panheadscrew O 8 0 e Oa 3 4 5 6 7 8 9 10 2 Accessories 2 Allen wrench holder 2 is used to prevent the loss of the Allen wrench Hang it in the appropriate place on the stand 1 2 r NX 1 3 English StarBoard FX 79E1 89WE7 1 2 3 StarBoard FX 79E1 89WEl Stand Stay option 1 Parts No stay Nut amp bolt set Introduction English StarBoard FX 79E1 89WE7 1 3 Role of Each Part 1 3 1 StarB
7. Solid Pen red cil Software Toolbar hidefun hide Adds a new blank page Select Solid Pen blue Show previous page Select Solid Pen green Show next page Select Fluorescent Marker Pen Hides displays the Topic List iS Select Eraser Switch to PC Operation Customizable button 1 Calibration 1s set as the default Customizable button 2 B Unassigned 1 About one time right click When the one time right click function button is pressed the next finger input becomes right click operational one time only If the function button is pressed the one time right click operation is not cancelled until a finger input 1s made Y 1 6 English StarBoard FX 79E1 89WE7 Introduction 1 4 Assembly and Setup When setting up the board keep the following in mind WARNINGS Install this product on a vertical and flat surface Do not install this product on a slanting surface ceiling or uneven wall Otherwise the equipment might fall possibly resulting in injury or the impact might cause product failure NOTICE Select a level and stable position Do not set 1t up near equipment that might generate electromagnetic waves or radio frequencies such as radio transmitters televisions copying machines or air conditioners Avoid locations that are dusty that are subject to extremely high or low temperatures or humidity or that are exposed to direct sunlight 1 4 1 Wall Mounting S
8. StarBoard FX 79E1 StarBoard FX 89WEI1 User s Guide Read this User s Guide and carefully retain it for future reference Before using this product carefully read and fully understand the safety instructions Store this User s Guide nearby for ease of reference FXE1 ML120901 Hitachi Solutions StarBoard FX 79ET1 89WET7 Notices Reproduction or reprinting without permission of this User s Guide or any part thereof is prohibited The contents of this User s Guide are subject to change without prior notice Every effort has been made to ensure that this User s Guide is complete and correct However should any questionable points mistakes etc come to your attention please inform the vendor Hitachi Solutions Ltd assumes no responsibility for losses resulting from or related to the use of this product Refer to 3 Appendix 3 4 Product Warranty Policy at the end of this User s Guide for details on the warranty and liabilities Precautions Regarding Disposal At time of disposal handle this product as industrial waste according to all applicable laws and regulations Disclaimers Hitachi Solutions Ltd assumes no liability and makes no warranty either express or implicit regarding the contents of this User s Guide Also the company makes no warranty as to the product s suitability merchantability or fitness for a particular intended use All products of Hitachi Solutions Ltd described in this User s Guide are p
9. able may result in scratching or damage to the cable Always lock the casters with stoppers on the front side after installing this product Failure to lock the casters may allow the product to move or slide 5 English StarBoard FX 79E1 89WE7 Safe Handlin 2 Dealing with Trouble N CAUTIONS What to do in case of emission of smoke strange odor or strange noise If an abnormal condition such as emission of smoke strange odor or strange noise happens to occur for some reason immediately disconnect the product s USB cable from the PC Confirm that the smoke or strange odor is no longer being emitted and contact a support center to request repairs Continued operation without repair may result in fire What to do if the product breaks or the USB cable is damaged If this product breaks or the USB cable becomes damaged for some reason immediately disconnect the USB cable from the PC and contact a support center Continued operation without repair may result in emission of a strange odor or smoke 3 Precautions Regarding Handling WARNINGS Do not hang from or climb on this product Failure to comply may result in personal injury if the product falls collapses or breaks into pieces Be particularly careful in the case of small children N CAUTIONS Do not splash with water or chemical compounds Do not place this product in a location subject to contact with water droplets or place any containe
10. ails on the input area see page 1 4 of this User s Guide StarBoard Software filesUninstall the StarBoard Software and may be broken or then re install it installation may not bel For details on installing StarBoard complete correctly Software see the StarBoard Software Installation Guide Other than the above Contact a support center 3 2 English StarBoard FX 79E1 89WE1 Appendix 3 2 System Specifications Specification StarBoard FX 79E1 StarBoard FX 89WE1 Detection method Infra red interception system LED pitch ata Sampling rate Approx 66 points second Interface USB 1 1 cable length 5m Effective screen Approx 79inches Aspect ratio 4 3 D Approx 89inches Aspect ratio 16 10 QJ size mm 1 633 W x1 225H 1 960 W x1 225H Board 1 852 W x1 282 H x35 D 2 179 W x1 282 H 35 D dimensions mm Overall dimensions including stand Powa 5V 500mA consumption Approx 21kg 39kg Approx 24kg 42kg 1 852 W x1 695 2 045 H x620 D 2 179 W x1 695 2 045 H x620 D Operating 5 C 35 C Humidity 20 80 RH without condensation requirements Storage 10 C 45 C Humidity 20 80 RH without condensation requirements Standards etc FCC Class B CE VCCI class A 1 This product uses infra red light to detect the coordinate position of the stylus pen or finger Do not operate near lighting that will obstruct the capture of the image This includes Locatio
11. arations This chapter describes the preparations to be made before using StarBoard First time users of StarBoard should read through this chapter 1 1 1 Product Outline The StarBoard is an extremely convenient and easy to use electronic whiteboard After setting up the provided software on a PC that is connected to a projector you can use your finger or the stylus pen option that is included with the product to operate the PC or import to the PC in real time characters or images that are drawn on the whiteboard 1 1 2 Features You can use your finger or the pen to operate the PC You can use your finger or the pen to operate a PC screen that is projected onto the board with a projector Two pen types are available the stylus pen that is included with the product You can write two people at the same time Two people can input simultaneously with dedicated purpose tools or contents It is effective for class and presentation You can write directly onto the PC screen After installing the provided StarBoard Software onto a PC you can use your finger or the pen to write characters or images directly onto the PC screen The input characters or drawn images are imported as digital data in real time into the PC where they can be saved or printed Compatible with PowerPoint presentations Characters or images can be written into presentations created with Microsoft PowerPoint which significantly improves the expressive power of
12. ard Software toolbar Settings StarBoard Check Connection and then check the connection If the StarBoard is not connected message appears StarBoard Software has not detected the StarBoard Check whether the StarBoard and PC are connected properly S gt arisard la enanar S Starfoard la not connecird k oe I Il I I If they are connected properly the StarBoard is connected message appears If the indication does not change even though you have checked the connection there is likely to be some problem For details see 3 Appendix Troubleshooting on page 3 1 in this user s guide If the positions of the pen tip and cursor are out of alignment select MENU on the StarBoard Software toolbar Settings StarBoard Calibrate OK and then perform position alignment 2 5 English StarBoard FX 79E1 89WE1 Appendix 3 Appendix 3 1 Troubleshooting Before assuming the product is broken be sure to check adjustments proper handling procedures the possibility of faulty cable connections etc Recognition Related Problems What to check What to do The StarBoard does notis the USB cable connected to Connect the USB cable to the PC recognise input the PC Is the USB cable connected to Connect the USB cable to the the StarBoard StarBoard Did you start the system in the Start the system in the correct correct sequence sequence For details on starting the system see page
13. ed use may result in fire or damage to this product 8 English S tarBoard FX 79E1 89WE71 Safe Handlin NOTICE Regarding the setup environment Set up this product on a level floor surface with a weight bearing capacity of 150 kg m or more and which is made of floor materials that will not deform or become depressed due to movement by casters Do not use this product in locations subject to high temperature or high humidity This product s usage environment conditions Temperature 5 C 35 C Humidity 20 RH 80 RH no condensation Do not set up in locations subject to vibration and or shock of impact Vibration and or shock of impact may harm internal components of this product resulting in damage to it Do not set up this product in a location subject to vibration or shock of impact Do not set up this product near a high voltage line or power source If this product is set up near high voltage lines or power sources it might receive interference Do not set up in a location subject to direct sunlight or near a heater Failure to comply may result in deformation of or damage to this product 6 Precautions Regarding Disposal NOTICE At time of disposal handle this product as industrial waste according to all applicable laws and regulations When disposing of this product the user should follow all laws and regulations of the locality in which it is being used 9 English Sta
14. etup Method WARNINGS Keep the wall material in mind when installing Installing the board on to the wall in a way that does not suite the wall material may result in the board falling off the wall causing injuries or damage to the board Furthermore wall installation may not be possible depending on the wall For details consult with your dealer Keep the wall strength in mind when installing Only use this product after confirming that it 1s securely attached and will not fall Furthermore be sure to install using a wall mounting bracket capable of supporting a weight of at least 50 kg 1 7 English StarBoard FX 79E1 89WE7 Introduction 1 Install the wall mounting brackets Determine the height at which the board will be installed and install the wall mounting brackets onto the StarBoard at the positions shown in the diagram below The wall mounting brackets are provided with the StarBoard 3 on page 1 2 More than 1300mm Back of the board 1 8 English StarBoard FX 79E1 89WE7 Introduction 2 Install the board Prepare the following tools Spanner 10mm diameter Hexagon wrench large small Provided as an accessory Screwdriver N WARNINGS Wall mounting work should be performed by a construction specialist Improper work may result in death or personal injury due to the product falling during operation Always use the specified mounting unit CAUTION Be sure to use three or more
15. h StarBoard FX 79E1 89WE1 Safe Handlin 1 Precautions Regarding Operation Do not make modifications Do not make any adjustments repairs or modifications not given in this User s Guide as doing so may lead to personal injury or damage to the product Do not open or remove cover of this product Failure to comply may lead to personal injury or damage to the product Refer internal inspections adjustments and repairs to your dealer or support center Do not place objects on top of this product If a foreign object falls on top of or inside this product 1t may lead to personal injury or damage to the product In order to prevent damage by static electricity touch a nearby metal object with your hand to discharge any static electricity before touching this product Static electricity from your body may cause damage to this product Do not allow the LED cover surrounding the board to become dirty or scratched If the LED cover becomes dirty or scratched it may lead to improper coordinate detection Do not use a USB cable extended Use of a USB cable extended may result in malfunction Do not use any cables other than those provided Furthermore do not use cables that are longer than 5m Do not place heavy objects on pull on or subject the USB cable to excess heat Failure to comply may result damage to the USB cable Always grasp the plug of the USB cable when connecting or disconnecting Pulling on the USB c
16. ion Method Before Starting to Connect Equipment Install the StarBoard Software on your PC before starting to connect equipment The equipment might not operate correctly if it is connected without the software being installed Connect the PC projector and StarBoard according to the following procedure StarBoard Gago E amam E OODANRAGARCMAAAM A O000NGAGECMaDE A A 1 Connect the RGB cable to the projector s RGB connector and fasten with screws 2 Connect the opposite side of the RGB cable to the PC s RGB connector and fasten with screws 3 Connect the USB connector at the bottom left of the StarBoard to the USB port on the PC using the provided USB cable 4 Connect the power supply cables of the PC and projector to the power supply NOTICE Do not touch board at the time of plugging USB cable It may cause of malfunction 1 14 English StarBoard FX 79E1 89WE1 Introduction About PC Earth Depending on your PC an incorrect operation might be caused by PC noise via the USB cable If this happens verify that the earth of your PC s power supply cable is comnected If the earth 1s not connected 1t might cause an incorrect operation For Windows XP When you connect the PC and StarBoard Found New Hardware Wizard window starts up Select No not this time and click Next Found Mew Hardware Wizard Welcome to the Found Naw Hardware W
17. izard Windia al peerch hor current and updated pafas En lata on yo compra or re haras mailer LD a on de rior Update Web site path pone permission Can iin correcto Ando Linda Eo arch bin rota C Yer lhe hra iri Lic Her bo ordre Select Install the software automatically Recommended and click Next Found Mes Hardware Wizard Thig wizard helps acy natal pofterane or var dd Drees ii pour hardware came mith an installation CD E on Hoppy disk mian A now hat do yay rank the waza bode TEF lhi illes iir H rra e 0 lra hom a EA i bec eh rel Dick Hesi o cortine 1 15 English StarBoard FX 79E1 89WET1 How to use 2 How to Use 2 1 Basic Operations This chapter gives a description of the basic operations of the board 2 1 1 Character Input To input characters use your finger or the stylus that was provided with the product NOTICE Do not scrape or strike the board surface by stylus pen Failure to comply may result in damage on the board surface Use an input tool with a thickness of least 7 mm When inputting to this product use a tool that is at least 7 mm If a pen or similar tool with a thickness of less than 7 mm is used the input will be unstable Also do not use tools with a sharp tip such as a ballpoint pen If such a tool is used incorrectly it could damage the surface of the board Sleep mode is unavailable on Windows XP Unplug USB cable from StarBoard if you use sleep
18. mode Using the stylus pen Use the pen on the board with your body kept sufficiently away so that your palm and elbow do not touch the board If your hand or elbow touches the board or you are within 1 cm of the board it might cause an incorrect operation 2 1 English StarBoard FX 79E1 89WET1 How to use Using your finger Extend your finger and touch the board In the same way as the stylus pen if you touch the board with anything other than your finger or you are too close to the board 1t might cause an incorrect operation 2 1 2 PC Operations When performing PC operations by pointing or giving presentations without inputting characters 1t is convenient to extend the stylus pen and use it as a pointer HITACHI StarBoard m m e WN 6 Aw OE a e TN d Y RRA BEM NNANARNGC CUTS A A 2 2 English StarBoard FX 79E1 89WET1 How to use N CAUTION Do not strike the board forcefully with the stylus pen bend it or apply an excessive load to it Failure to comply may result in damage to the stylus pen or personal injury 2 3 English StarBoard FX 79E1 89WET1 How to use 2 2 Start Method 2 2 1 Start Method Windows virsion 1 Connect the devices with reference to the connection method on page 1 11 2 Turn on the power switch of the projector 3 Turn on the power switch of the PC to start Windows 4 Adjust the position of the pr
19. ns where direct sunlight strikes the board surface or comes from the side Locations with white incandescent lighting or strong infrared source directly overhead 3 3 English StarBoard FX 79E1 89WE1 Appendix 3 3 Proper Care and Cleaning Clean the StarBoard periodically so that you may use it for a long time to come 1 Cleaning the StarBoard To clean the StarBoard use a soft cloth dampened with whiteboard cleaner or a diluted neutral cleansing agent that does not contain a polishing compound Never use a solvent such as thinner Note that rubbing or striking the StarBoard surface with a finger nail or other hard object may result in scratching 2 Cleaning the LED cover Dirt on the LED cover affects the operations performed using the stylus pen or finger Clean the reflective tape periodically or whenever 1t becomes dirty or soiled To clean the reflective tape apply a minimal amount of diluted neutral cleansing agent that does not contain a polishing compound to a soft cloth and wipe Never use a solvent such as thinner Use a soft cloth to prevent scratching of the LED cover surface 3 4 English StarBoard FX 79E1 89WE1 Appendix 3 4 Product Warranty Policy 1 During the free warranty service period if a malfunction occurs during normal use the malfunction will be corrected without charge according to the provisions of the warranty Furthermore if the customer registration card accompanying the warran
20. oard Introduction o gt 3 6 Y U E a e A N A nm n Na o O 3 e DO QQ Y AE A ch 1 Function Area Left and Right Shortcut buttons for functions that are frequently used in applications are located here Refer to the next page for details 2 Input Area Characters or images drawn in this area are imported into the PC When using the StarBoard in Projection Mode make sure that the image projected from the projector 1s kept within this area 3 USB Cable Used to connect the StarBoard with the PC 4 Casters Parts of stand These are the casters for moving the board After setting up the StarBoard be sure to lock the casters Lift up the tab to unlock a caster and press down the tab to lock it Locked Unlocked English StarBoard FX 79E1 89WE7 Introduction 1 3 2 Function Area The function area is provided with shortcut keys for the functions that are frequently used in the StarBoard Software Use by clicking the middle of the symbol with your pen or finger When using Windows all buttons except for the one time right click switching button can be customized You cannot customize the shortcuts with the software for Mac Refer to the online help for details The default settings are as follows Symbol Symbol ES Select one time right click Select Solid Pen black SJF Hides displays the StarBoard 3 Select
21. ojector so that the Windows screen projected by the projector 1s within the input area refer to page 1 4 of this User s Guide 5 Select Start All Programs StarBoard Software or double click the StarBoard icon on the desktop star Board software If the No connection icon in below appears on the Tasktray 1t means that the StarBoard is not connected Make sure that the StarBoard and the PC are properly connected If the StarBoard is properly connected the icon changes to Connected as above If the icon does not change despite correcting the connection there may be some other problem For details refer to 3 Appendix 3 1 Troubleshooting on page 3 1 of this User s Guide If the positions of the pen tip and cursor are out of alignment select MENU on the StarBoard Software toolbar Settings StarBoard Calibrate OK and then perform position alignment 2 4 English StarBoard FX 79E1 89WET1 How to use 2 2 2 Start Method Mac version 1 Connect the devices with reference to the connection method on page 1 11 2 Turn on the power switch of the projector 3 Turn on the power switch of the PC to start Mac 4 Adjust the position of the projector so that the Mac screen projected by the projector 1s within the input area refer to page 1 4 of this User s Guide 5 Select Go Applications StarBoard Software to start StarBoard Software 6 Select MENU on the StarBo
22. rBoard FX 79E1 89WE7 Safe Handlin Careful thought was given to the cautions on this device and in this User s Guide However unanticipated circumstances might occur When operating this product users themselves must exercise caution as well as follow instructions Warnings Contents Page s Install this product on a vertical and flat surface Do not install this product on a slanting surface ceiling or uneven wall Otherwise the equipment might fall possibly resulting in injury or the impact might cause product failure Keep the wall material in mind when installing Installation by means not suited to the wall material in question may result in the board falling Furthermore wall installation may not be possible depending on the wall For details consult with your dealer Keep the wall strength in mind when installing Only use this product after confirming that it is securely attached and will not fall Furthermore be sure to install using a wall mounting bracket capable of supporting a weight of at least 50 kg Wall mounting work should be performed by a construction specialist Improper work may result in death or personal injury due to the product falling during operation Always use the specified mounting unit Tighten the screws securely Failure to comply may cause the board to fall resulting in personal injury or may cause damage to this product due to shock of impact from the board falling Caution
23. resently for sale or are site licensed Users who purchased the aforesaid product s will bear the costs of all required services repairs and damages resulting from defects in this product and will bear the costs of direct or indirect damages including the loss of profits or required information that resulted from the product defects Moreover Hitachi Solutions Ltd retains the right to revise this User s Guide and to modify the contents thereof without any obligation to notify anyone 1 English StarBoard FX 79E1 89WE71 Product Assurance Provisions This product is limited to use in the country where the user bought this product For warranty details refer to 3 Appendix 3 4 Product Warranty Policy at the end of this User s Guide This Fourth version of the User s Guide FXE1 ML120901 is for the following products AH00329 StarBoard FX 79E1 AH00332 StarBoard FX 89WE1l Windows 1s a trademark of Microsoft Corporation U S and in other countries Mac and Mac OS are trademarks of Apple Inc registered in the U S and other countries Other trademarks and product names are trademarks and or registered trademarks of their respective holders Manual Creation Dates September 2012 Fourth edition FXE1 ML120901 All Rights Reserved Copyright c 2011 2012 Hitachi Solutions Ltd 2 English StarBoard FX 79E1 89WE71 Introduction Thank you very much for purchasing Hitachi solutions StarBoard FX 79E1 89WE1 henceforth
24. respond to the numbers in the parts tables on pages and 1 4 of this User s Guide Tighten with the spanner lt FX 79E1 gt 1 11 English StarBoard FX 79E1 89WE1 Introduction Tighten with the spanner o i lt FX 89WE1 gt 1 12 English StarBoard FX 79E1 89WET1 Introduction 3 Adjust the height Install the board on the stand assembled in step 1 Install the board according to the following procedure Furthermore this step should be performed by at least two people Numbers in the diagram correspond to numbers in the parts list on page 1 3 Board a Decide the level out of six at which the board will be installed and use the square holes on the back of the board to hang 1t on the Height Adjustment Stay b Verify that one of the board s square holes is attached securely to the Height Adjustment Stay on each side 2000000500004 c Tighten triangular knob screw to fasten the board to the board fixing bracket on each side 4 Adjust the height The StarBoard can be positioned at six height levels Adjust the height according to the following procedure Furthermore this work should be done by at least two people a Loosen the screws shown in 5 in the figure on page 1 9 b Lift the board to the installation height c Tighten the screws shown in 5 with a spanner 1 13 English StarBoard FX 79E1 89WE7 Introduction 1 4 3 Equipment Connect
25. rs containing water or other chemical compounds on top of or nearby this product Failure to comply may result in damage or fire if water or chemical compounds get inside this product 6 English StarBoard FX 79E1 89WE7 Safe Handlin NOTICE Disconnect the USB cable during extended periods of non use For safety reasons disconnect the USB cable if the product is not going to be used for an extended period of time Failure to comply may result in malfunction Handle the connection cable properly Improper handling of the connection cable such as jamming it against a wall undue bending pulling or twisting may result in overheating or damage due to exposure of the conductive core electrical short or severing of the cable Always use two or more people to move this product This product is a very large and heavy precision instrument Always use two or more people and take great care when moving this product Result in the personal injury or breakdown if the product falls Always disconnect the USB cable from the PC when moving this product Failure to comply may result in damage to the USB cable and or the product itself Do not subject to shock of impact This product is a precision instrument Excessive shock of impact may hinder further operation Take extreme care when moving this product 7 English StarBoard FX 79E1 89WE7 Safe Handlin 5 Precautions Regarding Setup Environment ZN WARNINGS
26. s Contents Page s Be sure to use three or more people for this work Failure to comply may cause the board to fall resulting in personal injury or may cause damage to this product due to shock of impact Do not strike the board forcefully with the stylus pen bend it or apply an excessive load to it Failure to comply may result in damage to the stylus pen or personal injury 10 English StarBoard FX 79E1 89WE7 Safe Handling NOTICE Notice Contents Page s Select a level and stable position Do not set it up near equipment that might generate electromagnetic waves or radio frequencies such as radio transmitters televisions copying machines or air P 1 6 conditioners Avoid locations that are dusty that are subject to extremely high or low temperatures or humidity or that are exposed to direct sunlight Do not touch board at the time of plugging USB cable P 1 11 It may cause of malfunction Do not scrape or strike the board surface by stylus pen E P 2 1 Failure to comply may result in damage on the board surface Use an input tool with a thickness of least 7 mm When inputting to this product use a tool that is at least 7 mm If a pen or similar tool with a thickness of less than 7 mm is used the input will be unstable Also do not use tools with a sharp tip such as a ballpoint pen If such a tool 1s used incorrectly 1t could damage the surface of the board Sleep mode is unavailable on Windo
27. s outside the scope of this warranty 9 The aforementioned provisions define this warranty and they supersede those of all express or implied warranties that include legal defect liability 10 No warranty if customer fixed the product in a method other than our company specified Our company has no responsibility for compensation of board falling accident 11 This warranty is limited to use of this product within the country where the user bought this product 3 6 English
28. ty is not returned to our company the customer information will not be registered so free repairs might be unavailable After receiving this product please immediately fill out and return this customer registration card 2 The warranty coverage is listed in the following table Product Name Part Name Warranty Coverage StarBoard Digitiser Light transmitting board light receiving board Function Area Sticker Wall Mounting Bracket Send o O Explanatory note Covered by warranty excluding wear or physical damage Not covered by warranty 3 Please refer to the warranty sheet for this product s warranty service period 4 Even during the warranty period there will be a repair charge in the following cases 1 2 3 4 5 6 7 8 9 10 If the registration card accompanying the warranty is not returned to our company If the warranty is not presented If specified fields on the registration card accompanying the warranty are not completed or if the wording has been changed without authorisation The warranty applies only to the original purchasers It does not apply to a third party to whom the customer resold this product In the event of a malfunction or damage resulting from the customer s improper handling e g a fall impact etc caused by the customer during transportation or movement In the event of problems resulting from handling contrary to the
29. ws XP Unplug USB cable from StarBoard 1f you use sleep mode 11 English StarBoard FX 79E1 89WE7 Contents Contents INTRODUCTION n 1 1 PREPARAN ose NR en ne nee eR Re me eRe ee AREA MEN bn ER E lo Ao 1 1 I O A A O ores E ees 1 1 A naa N AEE EA E E E EET 1 1 ule ARS O AEREE ASEE AN AAE ANE EN 1 2 O ri A Getto seated ne shed Ae erie senda EE NE EE A A aad Goss diet aad ate ie 1 2 D2 BANA aa 1 3 1 2 3 StarBoard FX 79E1 89WE1 Stand Stay Option occccccccccnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnos 1 3 LS ROPE OF EACH PART a ea ole le Cedo Sota ed nie pole Mel as 1 5 EA A O ae ee eee ene eee 1 5 LIZ ACCOM AMA diodo 1 6 1A A SSE MBIEY AND OE PUP kui on rre lr ieee ee eee eee 1 7 1 4 1 Wall Mounting Setup Method coccoccnncccnoccconccocenoninncoconococononenococonicocenoninococecicacininenes 1 7 1 42 Smund SEU MIE IS Ed 1 10 LAS Equipment Connection Method AAA A sconces EEEE EEE A EEEa 1 14 2 AHOW TO USE iii ld 2 1 DAV BASIC OPERATIONS costat ear lacio 2 1 ECO sis 2 1 ee E een ee een mee ee Meer Cerne eee eer nae ee ere pener sere 2 2 DS A e ee en 2 4 2 2 1 Start Method Windows Vil S100 daa 2 4 2 22 Start Method Mac Versionen dd TEE 2 5 APPEND aa E N E AN N A 3 1 SIRO BESO OU rese ion Seeds 3 1 BZ OY STEN SPECINI A TON E E E E AEE AEE Loco Do oo AENT 3 3 3 3 PROPER CARE AND CLEANING su tii 3 4 3A PRODUCT WARRANTY PO a a od 3 5 12 English StarBoard FX 79E1 89WE71 Introduction 1 Introduction 1 1 Prep
Download Pdf Manuals
Related Search