Facade_Manual de usuario-ES_V02_1301-EN
Contents
1. Parklex FACADE USER MANUAL EN V02 1301 Composites Gurea S A Inscrita en el Registro Mercantil de Navarra Tomo 160 Folio 175 Hoja NA 4886 C I F ES A 31 01359 2 Parklex RECEIPT OF MATERIAL Check the condition of the package In the event of any visible damage write this down on the delivery note In the event of any hidden damage inform of such within 72 hours No claims will be admitted for transport reasons if any of these instructions are not followed HANDLING amp STORAGE We recommend you keep the Facade panels in their original packaging until they are ready to be installed In the event that any panel needs repackaging this shall be done in the same conditions as the original packaging During transport the Facade panels must be properly strapped bearing in mind that the straps move up and down easily and can quickly become frayed They must always be transported horizontally The panels must be stored in a closed ventilated area at a room temperature of 10 to 25 C and with an air humidity level between 30 and 70 The panels must not be stored vertically they must always be stored horizontally with a distance between supports that does not exceed 600 mm The floor on which the pallet rests must be free of any materials or substances that may cause damage We recommend you avoid exposing the two sides of the Facade panels to different humidity and temperature conditions In the parti2. cular case of Facade panels that have fastening elements attached e g brackets for hidden mechanical installation they must be stored in a front against front back against back pattern and so on using intermediate wooden or plastic supports placed at a distance of up to 600 mm between supports Once the packaging has been opened we recommend you only take out the Facade panels that are going to be used immediately The rest must remain in storage in the same conditions as they were in the original packaging These same instructions are also valid for cut parts Improper storage handling of the panels can cause permanent deformation in the panels MACHINING Due to their composition the FACADE boards are relatively hard The tools used for cutting the boards must be more resistant than those used for most woods or wood based materials We recommend you use tungsten carbide Widia or polycrystalline diamond PCD tools as they are longer lasting The cutting tool must be perfectly sharpened or it could cause splintering on the sides For further details about machining please see the FACADE CATALOGUE or contact PARKLEX parklex parklex com INSTALLATION INSTRUCTIONS PARKLEX FACADE is designed for use as external cladding on ventilated facades that must have a freely ventilated air chamber All installations must strictly follow the technical instructions given in the FACADE CATALOGUE Avoid installing the material in extre
3. me climatic conditions PARKLEX will not be responsible for the use of any other assembly system that is not included in its FACADE CATALOGUE and or website www parklex com except where it has given express authorisation The use of safety goggles and gloves during the panels handling and cutting processes is strongly recommended Likewise all the habitual health amp safety requirements must be taken into account as regards dust extraction and collection fire prevention and protection measures etc Composites Gurea S A Zalain auzoa 13 31780 Bera Navarra Spain T 34 948 625 045 F 34 948 625 015 parklex parklex com www parklex com Parklex PACKAGING WASTE The packaging is made up of three different materials cardboard wood and plastic which can be easily separated and recycled MAINTENANCE Cleaning The Facade boards are protected by a special film that must be removed immediately after being installed on the fagade Dirt does not stick easily to the surface of the Facade board Nevertheless if the surface gets dirty or there is any adhesive residue left from the protective film it can be cleaned using a soft cloth with warm water and liquid detergent never dry rub the surface Never use abrasive detergents For persistent dirt the board s surface can be cleaned with a non colour treated soft cloth dampened with benzene free light petroleum 40 60 C light naphtha Never use sponges
4. ng possibilities include use as filling material in wood based panels for the construction industry e Landfill or dumping All specifications controlling the production and management of construction and demolition waste will be followed as well as any local regulations that may apply It might also be utilised in industrial incinerators e Sub structure the wooden aluminium or steel profiles can be directly reused for their original application or recycled if the buildings are carefully deconstructed FOR FURTHER INFORMATION PLEASE SEE THE PARKLEX CATALOGUE OR CONTACT PARKLEX PARKLEX PARKLEX COM Composites Gurea S A Zalain auzoa 13 31780 Bera Navarra Spain T 34 948 625 045 F 34 948 625 015 parklex parklex com www parklex com
5. or cloths with abrasive cleaning agents or scourers as they can damage the product s surface Do not use aggressive solvents such as Acetone Ethyl Acetate MEC varnish removers etc These can cause permanent damage partially or completely dissolving the surface protection film or causing it to crack this type of damage may not be immediately apparent The surface can be best dried by using an absorbent fluff free cloth It is advisable to do a cleaning test on a small area of the material to verify the procedure s effectiveness then go on to apply to the rest of the surface The use of chemical cleaning products and solvents must always be carried out following all corresponding health amp safety rules Maintenance The PARKLEX FACADE boards do not require any maintenance In the case of dirt please see the Cleaning section Repair Natural wood is a delicate material There is no established method for repairing PARKLEX FACADE boards Damaged panels must be replaced with new panels INFORMATION FOR DEINSTALLATION The FACADE product forms part of a ventilated fagade the main components of which aluminium steel wood and plastic can be easily separated and recycled INFORMATION FOR WASTE MANAGERS e Reuse The reuse of the PARKLEX FACADE panel will be encouraged in other applications with different requirements e Recycle the cellulose fibres in the core and the thermoset wood veneer can be recycled The recycli
Download Pdf Manuals
Related Search