User`s Manual
Contents
1. INSTALLATION Note If you are installing a complete Z Wave system for the first time please refer to the installation guide of your Z Wave Interface Controller before installing this module Warning Installation of this module requires connecting to household AC wiring Ensure that the power is off before doing any electrical work If you are not 100 comfortable working with AC wiring hire a professional electrician to perform the installation Use one of the following wiring diagrams to install the module in a system with one wall switch without indicator light two wall switches or one wall switch with an indicator light Note that the module can fit into most electric boxes For best results ensure the antenna is located away from metal and as close to the wall as possible To Control a Light Using 1 Wall Switch Antenna LED A Program SW To Control a Light Using 2 Wall Switches Neutral Wall SW2 Wall SW1 Antenna oO A Program SW To Control a Light Using 1 Wall Switch Equipped With an Indicator Light Antenna O i Program SW INCLUSION Now that the module is in its final location it can be included into the network Bring your Z Wave Interface Controller to the sensor s location The distance between the controller and the module should be less than 1 meter during the inclusion process 1 Following the instructions that came with your Z Wave Controller put the controller into inclu2. PID 11989 Z Wave IN WALL ON OFF MODULE Thank you for purchasing this ZWave In Wall On Off Module from Monoprice This module is a wireless Z Wave enabled device and is fully compatible with any Z Wave enabled network Z Wave is an interoperable two way RF mesh networking technology used for home automation and security Every AC powered Z Wave device acts as a signal repeater so multiple devices result in more possible transmission routes which helps eliminate RF dead spots in the network Any Z Wave enabled device displaying the Z Wave logo can be used with Z Wave devices from other manufacturers This module allows you to turn an appliance on or off wirelessly using the Z Wave controller You can also manually turn the appliance on off using a wall switch wired to the module As an AC powered Z Wave device it will act as a Z Wave repeater supporting FLiRS USER s MANUAL PACKAGE CONTENTS After receiving the product please inventory the contents to ensure you have all the proper parts as listed below If anything is missing or damaged please contact Monoprice Customer Service for a replacement 1x Z Wave In Wall On Off Module 1x User s Manual SPECIFICATIONS Protocol Z Wave Operating Frequency 908 42 MHz Operating Range up to 100 feet line of sight Operating Temperature 5 140 F 15 60 C Operating Voltage 100 240 VAC 50 60Hz Maximum Resistive Load 800W for 110VAC 1300W for 220VAC
3. de mode 2 When prompted turn the wall switch on and off four times or press the Program Switch on the module four times This completes the inclusion process EXCLUSION If you wish to remove the module from your network you will need to exclude it 1 Following the instructions that came with your Z Wave Controller put the controller into exclude mode 2 When prompted turn the wall switch on and off four times or press the Program Switch on the module four times This completes the exclusion process PROGRAMMING By default the module is configured to be installed into a system with a single wall switch with a light indicator If you are installing it into a single switch or dual switch system with no light indicators you will need to program the module This can be done using the Z Wave controller or physically using the Program Switch on the module Programming Using the Z Wave Controller 1 Following the instructions that came with your Z Wave controller put it into Configuration mode 2 Select Parameter Number 01 Size 01 3 Set the Parameter Value to 01 or 02 depending on the type of wiring situation you will be using 01 for a Single Wall Switch without Indicator Light or for Two Wall Switches 02 for a Single Wall Switch with Indicator Light Programming Using the Program Switch 1 Press and hold the Program Switch on the module for about 3 seconds 2 If the LED blinks once the module is configur
4. ed for a Single Wall Switch without Indicator Light or for Two Wall Switches 3 If the LED blinks twice the module is configured for a Single Wall Switch with Indicator Light RESET TO DEFAULT To reset the module to the factory default settings perform the following steps 1 Ensure that the wall switch is off 2 Press and hold the Program Switch While holding the switch turn on the wall switch 3 The LED on the module will begin flashing indicating that it is no longer included in a Z Wave network OPERATION You can turn the appliance connected to this module on or off manually using the wall switch es or wirelessly using the Z Wave controller Use the following codes for wireless operation ON Binary Switch Set OxFF OFF Binary Switch Set 0x00 Z WAVE COMMAND CLASS This module supports the following Z Wave commands COMMAND_CLASS_ASSOCIATION COMMAND_CLASS_CONFIGURATION COMMAND_CLASS_MANUFACTURER_SPECIFIC COMMAND_CLASS_SWITCH_ALL COMMAND_CLASS_SWITCH_BINARY mapping COMMAND_CLASS_BASIC COMMAND_CLASS_VERSION FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may ca
5. use harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into and outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment
Download Pdf Manuals
Related Search