gfk2436G IC200UEM001
Contents
1. pace y Press Down _ ee ae eee ee Daea Latch and Remove These fj ri Two Doors XQ J 2 Ifa port type Option Module is being installed orient the connector on the Option Module with the connector in the Micro PLC Be careful to avoid contact with the exposed components in the module Connector for Option Module Screws for Option Module Press the Option Module downward until it clicks into place 4 Install the screws provided with the Option Module into the corners indicated above Connector for Memory Pack Module Port lt Connector 5 If a Memory Pack Module is being installed orient the connector on the back of the Memory Pack Module with the connector on the Micro PLC or port type Option Module Press the Memory Pack down until it clicks into place 6 Install the protective cover s If only the Memory Pack Module is used both covers may be installed If a port module is used the right hand cover is not installed and the port connector remains accessible Setting the IP Address Key items to remember when setting the IP address on the VersaMax Micro Ethernet module IC200UEMO001 When connecting via Ethernet point to point a crossover cable is required IP address setting must be saved to the Flash on the Ethernet module or it will be lost during power cycle The2. Breson O b Response Nothing quie fo f sen response C SLT Connect With any character oloo Remote IP Address This setting specifies the remote IP address through which the communication needs to be established D disconnect N Unreachable Remote Port The setting represents the destination port number in TCP connections It is the number that identifies the channel for remote initiating connections Note See the reserved port numbers from the table specified in Port Number section DisConn Mode Set to zero FlushMode Set to zero DisConnTime Set to zero SendChar 1 Set to zero SendChar 2 Set to zero GFK 2436G August 2013 VersaMax Micro 20 40 64 PLC Ethernet Option Module IC200UEMOO01 Examples User entries are shown in bold To configure the Modbus TCP Client in IC200UEM001 through TELNET Connect PLC with IC200UEMO001 on port2 in the Network For this example the IP address of the IC200UEMO01 is 10 10 0 5 Load the Ethernet Option Module firmware upgrade kit 82A1588 MS10 000 B1 Type TELNET 10 10 0 5 9999 at command prompt Configure the parameters of the Ethernet Option Module as follows Modbus TCP to RTU Bridge MAC address XXXXXXXXXXXX Software version 02 5 090526 XCARD Press Enter to go into Setup Mode Model Device Server OEM Firmware Code G5 Modbus TCP to RTU Bridge Setup 1 Network IP Settings IP Address
3. Downloading Ethernet Drivers The Ethernet drivers for the Ethernet Option Module are downloaded from www ge ip com support Files and passwords Upgrade Kit for Destination GE Intelligent 82A1587 MS10 000 B1 Platforms SRTP Modbus TCP 82A1588 MS10 000 B1 Client and Server in single firmware Tunneling or Pass 82A1589 MS10 000 B1 Thru When the Ethernet option module is loaded with the Modbus image it cannot communicate with PME When the Tunneling image is loaded the 175000 baud rate is configurable only when the CPU Performance parameter is set to High in Telnet Configurator The CPU Performance parameter is available in the Expert Setting menu Downloading is done using the PumpKIN utility which is included To download a driver perform the following procedure Only one driver can be present at one time After the driver has been downloaded you will have to reconfigure the port using Telnet To download Ethernet drivers 1 Open the PumpKIN Utility x j re fr PumpKIN started N Milo Milo Milo Bs BP Ba Bs i I I I 2 Click on Put File and Local file to be downloaded Modbus_TCP 3 Enter password G5 case sensitive must be upper case G in Remote file For Remote host enter the IP address of the Micro PLC for example 10 10 0 2 Ss x Local file Dl Micro 64 Ethernet Modbus TCP Modbus_TCP Remote file Type octet Block 1024 G5 Remote host
4. 10 10 0 2 00 Pl Ad ian OK Cancel 4 When the file is downloaded the utility will respond with the following Uf Pumpkin x gt AS ASO ASO ASO ASO ASO O AS z EE RE RE a E a E jem r Put File NNN NNNNA fh PumpkiN started Sending GS to 10 10 0 2 Transfer of G5 has successfully completed 7 GFK 2436G August 2013 VersaMax Micro 20 40 64 PLC Ethernet Option Module IC200UEMOO01 5 When the transfer is accomplished go back to Telnet and configure the settings by following the procedure listed under Setting the Permanent IP Address on page 2 Refer to GFK 1645 for more information on configuration options 6 Settings are now complete Verify that Port 2 matches above configuration by connecting to the Micro PLC serial port and checking hardware configuration Security Settings Note This information replaces the Security Settings for the Ethernet Option Module section in chapter 14 of GFK 1645J and will be included in the next revision of that manual Security settings are provided to prevent unauthorized access to the Ethernet Option Module configuration mode Five security parameters are supported for the Ethernet Option Module firmware versions 3 3 and later Security settings are provided for the three protocols SNP SRTP Modbus TCP and Tunneling These parameters allow you to configure the Telnet password enable the required ports and disable the unused port
5. Enter After configuring all the parameters Telnet will display the configured parameters Press S to save the configuration to the Ethernet module You will see the messages Parameters saved Restarting and then Connection to host lost
6. changes to functions features or compatibility IC200UEM001 CD Firmware release 3 3 addresses issues listed below and adds new security settings listed in New Features and Enhancements in this Revision Programmer and Micro CPU firmware requirements same as version BC Upgrades All previous versions can be upgraded to this firmware version Once the module is upgraded to the 3 3 version it will not support downgrade to older revision Attempting to downgrade firmware may cause the module to fail permanently Note To reduce the risk of this being accidentally or maliciously used to permanently disable the module GE IP strongly recommends that TFTP be disabled by the user and only enabled via password protected telnet when a firmware update is required Functional Compatibility The default data rate with Ethernet option module firmware version 2 0 is 175000 bps Micro firmware versions below 3 83 do not support 175000 bps If firmware version 2 0 is to be used with Micro firmware versions prior to 3 83 the data rate on Ethernet Option module should be changed to 38400 bps or less as per the requirement Problems Resolved by this Revision The Ethernet Option module would stop communicating and not respond to any command This firmware release corrects this issue New Features and Enhancements in this Revision Additional configuration options have been added to the Ethernet Option module In the T
7. for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Note This Class A digital apparatus complies with Canadian ICES 003 Changes or modifications not expressly approved by GE could void the user s authority to operate the equipment Configuration Use of the Port Option module as Port 2 and the protocol selection must be set up in the configuration software After making those selections the communications parameters can also be configured The option port should be configured for Ethernet If the configuration and hardware do not match the PLC logs a System Configuration Mismatch fault in the PLC Fault Table The configuration options are SRTP Server Modbus TCP Client Server Pass Through or Tunneling Port Mode Parity Stop bits Time Out Turnaround Time Port Mode Port Type Data Rate Flow Control Parity Station Address Modbus TCP Client Support Refer to the VersaMax Nan
8. second port of the Micro PLC must be configured for Ethernet Setting the Temporary IP Address First set up a temporary IP address using Proficy Machine Edition Logic Developer 1 Open your project 2 Click on Utility on the Navigator box 3 Click on Set Temporary IP Address 4 Enter a Temporary IP address and MAC address for the Ethernet module MAC address is located on the front of the Ethernet module The IP address is only temporary and when Micro PLC is power cycled the IP address will be lost 5 Once Set IP is clicked you will get confirmation that temporary IP has been set At this point you can go on line with Machine Edition via Ethernet and do any function that you would do with a serial connection Setting the Permanent IP Address 1 Go to C Prompt on your computer and type Ping IP address and press the Enter key This step is required to establish the ARP table by creating an entry in the table The address pinged should reply with Pinged data example c Ping 10 10 0 5 and return data 2 Type arp a space between p and a You should see at least one entry in the ARP table example c arp a 3 Type aro s IP address including dots MAC Address of the Ethernet module including dashes You will not see any reply on the screen example c arp s 10 10 0 5 00 20 4a ff ff e9 4 Type telnet IP address 1 leave space between IP address and 1 and press the Enter key
9. GFK 2436G August 2013 VersaMax Micro 20 40 64 PLC Ethernet Option Module IC200UEMOO01 Module Description This datasheet describes the Ethernet Option module for a VersaMax Micro 20 40 or 64 PLC CPU This module cannot be used with other types of VersaMax Nano or Micro PLCs For more information about Option Modules and about VersaMax Micro 20 40 and 64 PLCs please refer to the VersaMax Nano and Micro PLCs User s Manual GFK 1645J or later Ordering Information RJ 45 10 100 Mbit Ethernet VAOU VE NGO Communications module supporting SRTP Ethernet Option Module Ethernet Module IC200UEMO001 can be used with a Micro 20 40 or 64 Point PLC to provide an Ethernet Port Connector for Memory Pack Module gt When installed on the Micro 20 40 or 64 PLC the Ethernet Port Option Module becomes Port 2 It supports the following communications protocols SRTP Modbus Server and client Separate download and pass through port Separate download Protocol options are available online at www ge ip com support FCC and ICES Requirements for the US and Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits
10. You will be prompted that the connection failed This is normal example c telnet 10 10 0 5 1 5 Type telnet IP address 9999 leave space between IP address and 9999 and press the Enter key You will be prompted to Press Enter to go into Setup Mode You have two seconds to press the Enter key again If you get the message Connection to host lost re enter telnet IP address and press the Enter key twice to get to the setup screen example c telnet 10 10 0 5 9999 Press 1 to change IP address Enter the desired IP address and Net Mask Press 2 to change Serial Settings For best performance set the baud rate to 175000 Setting should be Mode 1 RS232 175000 8 0 1 Port 2 needs to be configured with Proficy Machine Edition to match these settings Machine Edition should configure Port 2 for Ethernet and baud rate of 175000 When complete press S to save to the Ethernet module You will see a prompt that informs you Parameters saved Display will Restart and then Connection to host lost The data is now stored in the internal Flash of the IC200UEMO001 You can change the settings by repeating the above steps GFK 2436G August 2013 VersaMax Micro 20 40 64 PLC Ethernet Option Module IC200UEMOO01 Settings are now complete Verify that Port 2 matches above configuration by connecting to the Micro PLC serial port and checking hardware configuration Status LEDs Connector for Memory Pack Module
11. cccccceeeeees 10 10 0 5 Default Gateway 10 10 0 1 Netmask c0ccceeeeeeees 255 000 000 000 SNMP is enabled 2 Serial amp Mode Settings Protocol oarn Modbus RTU Slave s attached Modbus TCP Client disabled Serial Interface 38400 8 0 1 4 Advanced Modbus Protocol settings Slave Addr Unit Id Source Modbus TCP header Modbus Serial Broadcasts Disabled Id 0 auto mapped to 1 MB TCP Exception Codes Yes return OOAH and OOBH Char Message Timeout 00050msec 05000msec D efault settings S ave Q uit without save Select Command or parameter set 1 4 to change Press 2 Attached Device 1 Slave 2 Master 1 Press Enter Modbus TCP Client Enabled N Y Close Idle TCP sockets after 3 60 sec 0 leave open 10 Enter Serial Protocol 1 Modbus RTU 2 Modbus ASCII 1 Enter Enter serial parameters 38400 8 0 1 175000 8 0 1 After configuring all the parameters Telnet will display the configured parameters Press S to save the configuration to the Ethernet module You will see the messages Parameters saved Restarting and then Connection to host lost To change the Serial Parameter Settings in SRTP Protocol Connect PLC with IC200UEMO001 on port2 in the Network For this example the current protocol is SRTP and serial settings are 175000 8 0 1 The following procedure explains how to change the existing serial parameters to 38400 8 N 2 For this example th
12. e IP address of the IC200UEMO01 is 10 10 0 5 Type TELNET 10 10 0 5 9999 at command prompt Follow the below procedure to configure the parameters of the Ethernet Option Module MAC address XXXXXXXXXXXX Software version 01 8 090618 XPTEX Press Enter to go into Setup Mode VMSE GE Intelligent Platforms SNP 1 Network IP Settings IP AdOreSS Seion 10 10 0 5 Default Gateway 10 10 0 1 Netmask c0cccc ceca ees 255 000 000 000 2 CH1 Serial amp Protocol Settings Protocol Mode Mode 1 SRTP Ethernet to Serial SNP Slave Serial Interface 0068 175000 8 0 1 T1 Turn Around Delay 00002 msec T2 ACK NAK Timeout 09000 msec T3 Link Idle Timeout 10000 msec T4 After Break Delay 00400 msec 3 SNP ID to IP mapping table not used in this mode D efault settings S ave Q uit without save Select Command or parameter set 1 3 to change Press 2 2 CH1 Serial amp Protocol Settings Mode 1 SRTP Ethernet to Serial SNP Slave Mode 2 Serial SNP Master to Remote VMSE Select desired operating mode 1 Enter serial parameters 175000 8 0 1 38400 8 N 2 New T1 Line Turn Around Delay 2 1280 msec 1ms resolution 2 Press Enter New T2 ACK NAK Timeout 50 12 950 msec 50ms resolution 9000 Press Enter New T3 Link Idle Timeout 1000 60 000 msec 250ms resolution 10000 Press Enter New 14 After lt BREAK gt Delay 5 1280 msec 5ms resolution 400 Press
13. elnet interface a Security Settings group has been added to the configuration These parameters allow you to configure the Telnet password enable the required ports and disable the unused ports 7 gt Security Settings SNMP Disabled Disabled Disabled Disabled Enabled Note We strongly recommend configuration of the Telnet password and closing the unused ports This will reduce the exposure to security threats TFIP Download Port YYFEh Web Server Telnet Config Password For additional details see Security Settings on page 4 Telnet Configuration Note The Ethernet option module will be power cycled and reset under the following conditions A connection to the Ethernet option module is established through TELNET and disconnected immediately A connection to the Ethernet option module is established through TELNET the configuration is edited and you press Q Quit without Save GFK 2436G August 2013 VersaMax Micro 20 40 64 PLC Ethernet Option Module IC200UEMOO01 Serial IO Configurable Parameters Baud Rate The supported baud rates are 19200 38400 and 175000 This baud rate should match the baud rate of the configuration software I F Mode Interface Mode The Interface I F Mode is a bit coded byte entered in hexadecimal notation The following table displays available I F Mode options Note All bit positions in the table that are blank represent don t care bits for that
14. lashing Green when there is any activity on the network Status Red OFF No errors Red ON Duplicate IP address present or network controller error Red BLINK 2x sec No DHCP response or Setup menu active Module Specifications Processor Speed DSTni EX CPU 48MHz 256 kByte RAM 512 kByte FLASH Connection Type RJ 45 10Base T 100Base TX Ethernet Entity Type Client Server Bus Speed 10 100Mbaud Protocols SRTP preloaded Supported Modbus TCP Server and Client optional Tunneling optional Supports up to 8 Modbus TCP IP server channels Number of Connections Supported If client configured then 1 client and 7 server channels supported Supports 4 SRTP server channels Supports 1 connection for Tunneling Mode Full Duplex GFK 2436G August 2013 VersaMax Micro 20 40 64 PLC Ethernet Option Module IC200UEMOO01 Revision History IC200UEMO001 AA Initial release Compatible with VersaMax Micro 64 firmware release 3 5 and Proficy Machine Edition 5 5 IC200UEMO001 AB_ Improved noise immunity IC200UEM001 BC Added support for Modbus TCP Client enhanced data throughput 175 000bps and 16 character password security Firmware requirements Micro 20 40 and 64 firmware versions 3 83 and later Ethernet Option Module firmware versions 2 0 and later Programmer requirements Proficy Machine Edition Logic Developer PLC version 6 0 or later IC200UEM001 CC Labeling change No
15. o and Micro PLCs User s Manual GFK 1645J or later Port Mode Data Rate Flow Control Parity Stop bits Bits Characters Station Address Byte 1 to Byte 8 S NP Port Type Data Rate Flow Control 19 2 38 4 or 175 0 kbps default Odd default Even None 1 default or 2 Long RTU Slave 19 2 38 4 or 175 0 kbps default None Odd default Even None Valid range 0 247 Default 1 Disabled default or Enabled Enabling Modbus TCP Client Support sets the 100488 status bit ON Serial I O 19 2 38 4 or 175 0 kbps default None Odd default Even None 1 default or 2 Valid range 0 F Default 0 When the Ethernet Option Module is configured for Modbus TCP Client the configured Sequence Number and Command Data addresses should not overlap or conflict with any other variables used in the logic These addresses are reserved exclusively for communications between the CPU and Ethernet module when initiating Modbus TCP commands GFK 2436G August 2013 VersaMax Micro 20 40 64 PLC Ethernet Option Module IC200UEMOO01 Installation Instructions Power to the VersaMax Micro PLC must be turned off when installing or removing Option Modules 1 Remove the two doors shown below by pressing downward on the latches and lifting them away from the module i k J L ODO ooo0oo0o000o0 ooo0oo0oo0000 gt D gt ooo0oo0o0000 lt
16. particular option which can be set to either a 0 or 1 value Only RS 232C is supported and hence Bit 0 and Bit 1 always should be zeros If you attempt to select an I F Mode bit that pertains to RS 422 485 settings the WARNING RS 422 485 I F Modes Not Supported message displays uF Mode Option 7 6 5 4 3 2 7 0 aos RS 232C PN Pay ope Even Party tia Oda Parity ohn ft 1Stopbit ofif j2stopBit tit tf Common Interface Mode Settings Common I F Mode Setting RS 232C 8 bit No Parity 1 0100 1100 4C stop bit RS 232C 7 bit Even Parity 1 0111 1000 78 stop bit Flow Flow control sets the local handshaking method for stopping serial input output This should be set to zero always Port Number The setting represents the source port number in TCP connections It identifies the channel for remote initiating connections The range is 1 65535 except for the following 1 1024 Reserved well known ports 9999 TELNET Setup 14000 14009 Reserved for Redirector 30704 Reserved 77FOh 30718 Reserved 77FEh Warning Do not use the reserved port numbers for this setting because incorrect operation may result Connect Mode Connect Mode defines how the unit makes a connection and how it reacts to incoming connections over the network Connect Mode Option 7 6 5 4 3 2 1 o a Incoming Connection Never accept Incoming o oo T rAiways Accept p 11 fo
17. s 7 gt Security Settings SNMP Disabled Disabled Disabled Disabled Enabled Note We strongly recommend configuration of the Telnet password and closing the unused ports This will reduce the exposure to security threats TFIF Download Port 7FEh Web Server These ports are disabled by default A port must be enabled if the application needs a service associated with that port For firmware upgrade the TFTP Download must be enabled For connection with Device Installer Port 77FE must be enabled For use as web server the configuration for Web Server must be enabled By default Simple Network Management Protocol SNMP is Disabled For Modbus TCP and SRIP protocols these security settings options are in the Network IP Settings menu For Tunneling Passthrough these security settings are in basic parameters server menu The maximum password length is 16 characters These characters can be alphanumeric or special characters The password requires a minimum length of 8 characters A password set on a particular protocol s firmware remains in effect if the firmware is changed to that of a different protocol For example if a password is set on Modbus TCP firmware and later the firmware is changed to SNP SRTP the same password set on Modbus TCP firmware will still apply Status LEDs Link LED Amber Solid Amber Connection to Micro PLC established and network is connected Activity Green F
Download Pdf Manuals
Related Search