Home

NAD VISO FIVE Operating Instructions Manual

1. SPEA ERS CAUTION ATTENTION paw PEAKER IMPEDA E posa ye ANCEDES HAUT PARLEURS European Version only ATTENTION Please make sure that the VISO FIVE is powered off or unplugged before making any connections It is also advisable to power down or unplug all associated components while making or breaking any signal or AC power connections 1 SPEAKERS Connect the respective SPEAKER s FRONT L FRONT R CENTER SURROUND LEFT and SURROUND RIGHT channels to their corresponding loudspeakers Make sure the red terminal and black terminal are connected to the corresponding and terminals of the loudspeaker Use extra care to ensure that no stray wires or strands cross between posts or terminals at either end won The VISO FIVE is designed to produce optimum sound quality when connected to speakers with impedances within its operating range Please make sure that all the speakers are rated 8 ohms minimum per speaker NOTE Use stranded wire of at least 16 gauge AWG Connections to the VISO FIVE can be made with banana plugs US model only or by using bare wire or pins Use the transverse hole through the post for bare wire or pin connections By loosening the terminal s plastic nut make a clean neat connection and re tighten carefully To minimize the danger of short circuit ensure that only 1 2 inch of exposed wire or pin is employed when connecting 12V TRIGGER OUT The 12V TRIGGER OUT
2. If there is no XM tuner connected at the corresponding XM input terminal at the rear panel the VFD will show CHECK XM TUNER TUNING STATIONS There are three ways to tune to the XM channel you wish to listen Make sure to set your HTR 7 s DEVICE SELECTOR to TUNER prior to undertaking the following tuning options 1 ALL CH SEARCH All Channel Search Toggle front panel s MENU button to select ALL CH SEARCH Use the front panel or HTR 7 s lt gt or TUNE 44 lt 4 lt 4 gt P1 PP buttons to step up or down each available XM channel Press and hold lt gt for faster scanning of XM channels 2 CATEGORY SEARCH The XM channels are grouped into categories for easier selection of desired genre a Toggle front panel s MENU button to select CATEGORY SEARCH CAP and a corresponding category is displayed in the VFD CAP stands for categories the channels are grouped into i e Country Rock Jazz amp Blues etc b Use HTR 7 s amp or front panel s PRESET ke gt gt I buttons to step up or down the available categories c Press HTR 7 s lt P gt or front panel s TUNE lt lt 4 P buttons o select through the available XM channels within the selected category You can also use HTR 7 s TUNE Kd lt lt PP 1 gt gt buttons Tuning will only be limited to within the selected category d Repeat b above to choose another category 3 PRESET SEARCH Toggle
3. page e Onthe HTR 7 simultaneously press and hold DVD and 4 the Learn LED turns steady green e Press SURR MODE the Learn LED turns amber e Press AMP twice the Learn LED turns green e Press DVD again to exit the learning mode NOTE The HTR 7 control keys I1 I K44 gt P1 lt lt b gt and gt are not punch through function keys To use them for disc playback purposes make sure that HTR 7 s DEVICE SELECTOR is set to DVD Downloaded From Disc Player com NAD Manuals OPERATION USING THE HTR 7 REMOTE CONTROL COPY COMMAND FROM ANOTHER BUTTON You may copy a command from any HTR 7 key to any other key To copy a key function after entering the Learning Mode and pressing the desired key to be copied to simply press the device key from which you wish to copy having first pressed its Device Selector key if it resides on another page The status LED will turn green press the Device Selector key again to exit Learning Mode Example Copy the Pause command from the CD page to the AMP II key Onthe HTR 7 simultaneously press and hold AMP and 4 the Learn LED turns steady green e Press II pause the Learn LED turns amber e Press CD press II pause the Learn LED turns green e Press AMP again to exit the learning mode NOTE The copy and punch through functions are similar However if you copy a command and then subsequently delete or over write the origi
4. 1 Rotate the outer frame of the antenna 2 Insert the bottom edge of the outer frame into the groove on the stand 3 Extend the antenna cord SELECTING THE RADIO To select the VISO FIVE s tuner mode rotate INPUT SELECTOR knob on the front panel repeatedly until AM FM mode or the HTR 7 s numeric 5 while at AMP device selector page Press TUNE lt gt gt on the front panel momentarily to step up or down AM or FM frequencies Press and hold TUNE lt lt gt gt for more than 2 seconds to search up or down AM or FM frequencies the VISO FIVE s tuner will stop at the next sufficiently strong signal it encounters Pressing the TUNE lt lt gt gt during the search process will stop the search DIRECT TUNING If you know your desired station s frequency allocation you can tune directly to the station 1 Toggle ENTER button to switch between Preset and Tune mode see the lower line of the VFD Select Tune mode 2 Using the numeric keys of the remote control key in the frequency allocation of the station For example to enter 104 50MHz press 1 0 4 5 and O or press 1 0 4 and 5 NOTE Ensure that the DEVICE SELECTOR setting of your HTR 7 is set to TUNER 24 Downloaded From Disc Player com NAD Manuals SETTING RADIO PRESET The VISO FIVE can store as many as 60 30 FM and 30 AM stations of your favorite radio stations for immedia
5. CANCEL OPERATION You can cancel configuring a key by pressing the active Device Selector key before the learn process is complete the Learn LED will turn red Example Learning DVD Pause Position the HTR 7 and your DVD player s remote as described above Onthe HTR 7 simultaneously press and hold DVD and 4 the Learn LED turns steady green Press the HTR 7 s II key the Learn LED turns amber e Press and hold the DVD player s remote s pause key the HTR 7 s Learn LED flickers amber and then turns solid green The command is learned e Press DVD again to exit the learning mode PUNCH THROUGH The HTR 7 s punch through function allows you to retain a function key from one Device Select page to another so that for example the AMP SURR MODE function might still control the VISO FIVE when the DVD Device Selector page is active NOTE The HTR 7 s VOL keys are pre programmed as punched through for all Device Select pages VOL will operate the VISO FIVE s volume regardless of the currently selected device The SUB level control is similarly pre programmed as punched through To set a punch through after entering the Learning Mode and pressing the desired key to be punched through simply press the device key twice of the device to punch through to The status LED will turn green press the Device Selector key again to exit Learning Mode Example Punch through AMP SURR MODE key to the DVD
6. DVD Video Select to playback only the DVD Video content NOTES This setting is only available when no disc is loaded in the disc tray Selected mode becomes effective after you exit the setup menu When a DVD Audio disc is played back DVD Audio is shown in the VFD When you select DVD Video DVD Video will be briefly shown in the VFD and then reverts to normal display playback information MOVING TO ANOTHER GROUP Some DVD Audio discs divide content into different groups Your player enables you to quickly access different groups during playback via the on screen display 1 Press DISP during playback 2 Press lt gt to highlight G 3 Enter group number using the numeric buttons 0 9 PCM FORMAT The VISO FIVE is compatible with both 48 kHz and 96 kHz PCM formats 96kHz Select to handle 96kHz signal each type of signal will pass through without any further processing 96kHz gt 48kHz Select for 96KHz signal to be automatically converted to 48KHz enabling decoding of compatible media Downloaded From Disc Player com NAD Manuals OPERATION USING THE VISO FIVE VIDEO SETUP MENU DISC LANGUAGE Audio English Subtitle English Menu English Do not Save amp Exit Save amp Exit AUDIO SUBTITLE MENU Depending on the DVD media only the Audio Subtitles and Menus recorded on the DVD media are available When a language is chosen it will become the default setting unless the DVD m
7. During disc playback press this button to STOP and at the same time PAUSE disc playback RESUME will be shown at the VFD Press PLAY PAUSE button to resume play from the spot it was stopped If STOP button is pressed consecutively during playback disc playback will fully stop At full stop mode STOP will be shown in the VFD for DVD playback total number of tracks and total playback time for CD playback and CLIPMENU is displayed in the case of MP3 WMAV JPEG file playback 17 PLAY PAUSE Press this button to toggle between Play and Pause of a compatible disc If the disc tray is open press this button to automatically close the tray and start playback if a disc is loaded 18 OPEN CLOSE Press this button to open and close the disc drawer and simultaneously select the internal DVD CD player Pressing this button will also switch ON the VISO FIVE from standby mode and at the same time open the disc tray 19 DISC TRAY With the DISC TRAY open insert a DVD VCD CD or other compatible media disc face down onto the tray If the disc is placed upside down and it is a single sided disc NO DISC appears on both the VISO FIVE s VFD and the TV Monitor screen 20 FRONT INPUT Use these convenience jacks for occasional sources such as a camcorder tape player or a video game console or any other analog audio or composite or S Video video source Select the Front source input using the HTR 7 remote or the front
8. You can check the current code library on any Device Selector key as ollows Enter Library Mode by simultaneously pressing and holding for 3 seconds both the desired component s Device Selector key and the PROGRAM key until the Learn LED turns green Press the DISP key the HTR 7 indicates the current code library by flashing its CUSTOM VCR and MACRO keys For example to indicate code library 501 the HTR 7 will flash CUSTOM 5 imes pause and then flash MACRO once You might wish to make a note of your components code library numbers Summary of the HTR 7 Modes Mode Keys To Press for 3 seconds Learn Copy Punch Through Device Key 4 Key Delete Mode Device Key RTN Key Macro Record Macro Key Function Key Library Mode Device Key Program Key Back Light Timeout DISP Key Digit Key Factory Reset See Factory Reset above SLEEP MODE The Sleep Mode timer will switch the VISO FIVE to Standby mode automatically after a preset number of minutes Pressing the HTR 7 s SLEEP button once will display the setting of the sleep time increment Pressing he HTR 7 s SLEEP button a second time within a 3 second period will change the sleep time increment in 30 minute intervals after which time he VISO FIVE will automatically switch into Standby mode To adjust the sleep delay press the HTR 7 s SLEEP button twice first to display the sleep time increment and a second time to change the sleep time increment
9. service can be shown by pressing ENTER while at DivX Registration menu option OSD LANGUAGE osD English Do not Save amp Exit Save amp Exit OSD ON SCREEN DISPLAY The OSD of VISO FIVE can be shown in eight different language versions English French German Dutch Spanish Italian Russian and Swedish Select the language setting you prefer ABOUT THE VISO FIVE INTERNAL DVD PLAYER The VISO FIVE has exceptional playability It has support for DVD Video DVD R RW R RW DVD A SVCD with or without PBC Play Back Control VCD DivX Audio CD CD R RW and including recorded MP3 copyright protected WMA and JPEG files NOTE You cannot playback discs other than those listed above such as CD ROM CD Extra CD G photo CD and CD i data discs To do so may render the VISO FIVE permanently inoperable REGION MANAGEMENT INFORMATION The VISO FIVE s internal DVD Player is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc If the Region number described on the DVD disc does not correspond to the Region number shown on the back of the VISO FIVE the internal DVD player cannot play that disc The VFD will display REG Err Wrong Region in the OSD when an incompatible region disc is loaded DISC LOADING AND PLAYBACK You can open the disc tray by pressing OPEN CLOSE button even if the VISO FIVE is in standby mode The power indicator will turn from amber
10. AM FM DB iPod ABOUT XM RADIO The VISO FIVE is XM Ready which means that with the addition of separately sold XM Mini Tuner CPC 9000 and XM Mini Tuner Home Dock it has everything you need to listen to live XM Everything else is built right in Just subscribe to the XM service and your VISO FIVE will be ready to receive XM content NOTES Questions Visit www xmradio com Listeners can subscribe by visiting XM on the Web at www xmradio com or by calling at the time of printing this manual XM s Listener Care at 800 853 9696 Be ready with your Radio ID that can be found on the radio by selecting Channel 0 Check with your NAD audio specialist for other versions of XM Mini Tuner compatible with VISO FIVE CONNECTING THE XM ANTENNA Plug the end of the XM antenna into the corresponding XM antenna port on the rear panel of the VISO FIVE Press and hold DISPLAY button on the front panel to check the current XM channel s signal strength as shown in the VFD Press and hold DISPLAY again to exit signal strength check NOTES Refer also to your XM radio s guide on how to install the XM antenna for optimum signal reception The front panel TUNER MODE and MENU buttons function the same way at XM mode The MENU TUNER MODE key of HTR 7 is the equivalent button for both functions When using these HTR 7 buttons to navigate XM menu options ensure that the DEVICE SELECTOR setting of your HTR 7 is set to TUNER
11. The sleep time increment and a SLEEP icon will continuously display on the VISO FIVE s front panel Vacuum Fluorescent Display VFD Each consecutive press increases the sleep time in 30 minute increments from 30 to 90 minutes To cancel the sleep mode continue pressing the HTR 7 s SLEEP button until Sleep Off displays on the VFD Switching the VISO FIVE to standby from either the HTR 7 s OFF or the VISO FIVE s POWER button will also cancel the sleep mode NOTE In order to use SLEEP button make sure that HTR 7 s DEVICE SELECTOR page is set to AMP 33 REFERENCE TROUBLESHOOTING CONDITION No sound from all channels No sound from some channels No sound from Subwoofer VISO FIVE does not respond to HTR 7 remote control VISO FIVE does not respond to front panel commands or remote control The POWER is ON but the internal DVD player does not work No picture The playback picture is poor The internal DVD player does not start playback Parental Control cannot be changed 34 Downloaded From Disc Player com NAD Manuals POSSIBLE CAUSES AC power unplugged Power not switched on Outlet has no power Faulty missing cables Speaker connections faulty Speaker Settings channel s set to Off Subwoofer is off not powered or improperly connected Sub level set too low Batteries are flat or incorrectly inserted IR transmitter window o
12. VISO FIVE DVD Surround Sound Receiver Owner s Manual Downloaded From Disc Player com NAD Manuals IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR LATER USE FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE AUDIO EQUIPMENT 1 Read instructions All the safety and operating instructions should be read before the product is operated 2 Retain instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the product and in the operating instructions should be adhered to 4 Follow Instructions All operating and use instructions should be followed 5 Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 6 Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards 7 Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a we basement or near a swimming pool and the like 8 Accessories Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow th
13. also be switched to Prog Edit Off or Prog Edit On by pressing the PROGRAM key of the HTR 7 remote control Ensure that the DEVICE SELECTOR setting of your HTR 7 is set to DVD PROGRAM PLAYBACK To begin playback make sure that you are at View Program mode as set up from the View Filter section Press gt Play to start program playback Prg will be displayed in the VFD alongside the track number during program playback mode ERASING A TRACK FROM PROGRAM LIST To erase a track from the program list make sure that you are at View Program and Prog Edit On as set up from the View Filter section 1 Press 4 to go to the left pane of the menu screen 2 Select the track you wish to erase from the program list Press ENTER 3 Press gt to go to the right pane of the menu screen Use W to scroll down to Clear Program Press ENTER the selected programmed track is deleted NOTES Instead of selecting Clear Program a programmed track can also be directly deleted by pressing the CLEAR key of the HTR 7 remote control Ensure that the DEVICE SELECTOR setting of your HTR 7 is set to DVD Todelete more than one or all programmed tracks select the tracks one by one by pressing ENTER each time All tracks with mark will be deleted when CLEAR button is pressed or Clear Program is selected RESUME NORMAL PLAYBACK Make sure
14. assist in performing these upgrades ABOUT THE HTR 7 SYSTEM REMOTE CONTROL Packed with your VISO FIVE is the NAD HTR 7 remote control a full system remote especially designed for easy use and understanding Be sure to read the section Using the HTR 7 Remote Control to familiarize yourself with the remote s layout and operations before proceeding to setup your VISO FIVE You may opt to use your HTR 7 as your primary way to command your entire AV system The HTR 7 can be employed to operate additional NAD or other brand components such as a DVD CD player television satellite HDTV tuner VCR or virtually anything else that operates via standard infrared remote WHAT S IN THE BOX Packed with your VISO FIVE you will find e An AM loop antenna e AFMribbon wire antenna with balun e Aremovable AC cable if you wish any IEC standard AC cable of suitable wattage may be substituted e The HTR 7 remote control with 4 four AAA batteries e This owner s manual SAVE THE PACKAGING Please save the box and all of the packaging in which your VISO FIVE arrived Should you move or otherwise need to transport your VISO FIVE this is by far the safest container in which to do so We ve seen too many otherwise perfect components damaged in transit for lack of a proper shipping carton so please Save that box CHOOSING A LOCATION Choose a location that is well ventilated with at least several inches to both sides and behind and that
15. does not control your AD CD player DVD player or other component follow the procedure below to change the code library Begin by ensuring that the component you wish the HTR 7 to control is plugged in and powered up on not merely in standby To enter the HTR 7 s Library Mode simultaneously press and hold for 3 seconds both the desired Device Selector key and the PROGRAM key until the Learn LED urns green While keeping the HTR 7 pointed toward the component enter the first appropriate three digit code library number from the table below Press OFF If the component turns off press ENTER to accept that code library number and exit the Library Mode If the component does not turn off enter the next three digit code library number from the table When you enter the correct number the component will turn off press ENTER to accept that code library number and exit the Library Mode NAD PRODUCT NAD PRODUCT AEN DESCRIPTION Ass DESCRIPTION Receiver Processor 100 Discrete ON OFF 301 L75 L76 Tuner Receiver Processor 101 Toggle ON OFF 302 L70 Tuner 102 170 303 L53 Tuner 103 L75 304 L73 Tuner 104 Second Zone Commands 305 425 105 L70 306 445 106 L76 307 Txx5 Series Tuner 107 118 400 Tape Deck B 108 L53 401 TAPE Deck A 109 L73 500 TV 280 110 Stereo Receiver 501 MR13 Amplifier 111 Stereo Second Zone 502 MR20 112 Txx5 Series 503 PMR45 200 CD Player 600 T535 1562 1585 M55 201 CD Player old 601 7550 L55 202
16. enabled stations but it is by no means impossible that your favorite stations will not be broadcasting RDS data VIEWING RDS TEXT When an RDS enabled FM broadcast is tuned after a brief delay the RDS icon will light in the VISO FIVE s front panel readout and the readout s character section will show its station name PS text ROCK101 for example Press the front panel DISPLAY key to toggle the readout between this and the station s radio text RT readout if any which might scroll song or artist name or any other text of the station s choosing Downloaded From Disc Player com NAD Manuals OPERATION USING THE VISO FIVE AM FM DB iPod ABOUT DAB RADIO Until now analogue radio signals such as FM or AM have been subject to numerous kinds of interference on their way from the transmitter to your radio These problems were caused by mountains high rise buildings and weather conditions With Digital Audio Broadcast DAB you can now receive CD like quality radio programs without any annoying interference and signal distortion DAB broadcasts use digital signals rather than traditional analogue transmissions thus providing clear high quality reception You get far more robust reception and virtually hiss or crackle free sound with DAB as long as you are within a good coverage area With DAB the listener can scroll through a list of available stations then instantly tune to the station of his choice There is no need
17. front panel s MENU button to select PRESET SEARCH At this menu option a stored preset can be directly recalled by entering the preset number using the HTR 7 s numeric buttons 28 Downloaded From Disc Player com NAD Manuals DIRECT CHANNEL CALL While at either CATEGORY SEARCH or ALL CH SEARCH mode a desired XM channel can be directly tuned in by using the HTR 7 s numeric buttons To key in XM channels that are less the 3 digits press 0 in place of the digit or press ENTER after entering the XM channel number For example to enter XM channel 8 press 0 0 and 8 or press 8 then ENTER VIEW XM INFORMATION Toggle DISPLAY button to display the XM information of the selected channel such as the XM channel category XM station name artist name song title or any other text as supplied for the channel SETTING XM PRESETS The procedure for storing XM channels is the same method as stated in the section SETTING RADIO PRESETS under LISTENING TO AM FM RADIO You can store up to 30 XM channels For immediate recall of stored XM presets press the front panel s PRESET K44 gt P 1 button or HTR 7 s PRESET amp keys to step up or down the stored XM channel presets ABOUT THE iPod INPUT FEATURE The VISO FIVE is equipped with a data port in the rear panel where an optional NAD IPD 1 Dock with iPod NAD IPD 1 can be plugged in With the NAD IPD 1 linking the VISO FIVE wi
18. i i EER 6 ABOUT THE HTR 7 SYSTEM REMOTE CONTROL 0 0000 6 GETTING STARTED cscs cec tonks cee aiani a 7 WITAT SIN TIEBOX nc ataranaeentamnneedesersmeeepsaannarierennaans iD CHOOSING A LOCATION ic crtn vice ental rieanrtie vasa erialeomennes 7 QUICK START eisiu an e iE EAE E 7 IDENTIFICATION OF CONTROLS FRONT PANEL 0 ccc ce ccc c eee eee e cence eens eeseenseeeees 8 REAR PANEL c ccc cce cece cee e sees eee eeeeeeseeeseeees 10 SETUP SETTING UP THE VISO FIVE ccccee cee cee cee cennseeeenees 12 ABOUT THE ON SCREEN DISPLAY OSD 00000ee eee 12 SELECTING SOURCES epiese aree 12 ADJUSTING TREVOUYME sires dinesig EA a owns 12 ADJUSTING CHANNEL LEVELS ON THE FLY 0 0 13 ADJUSTING THE TONE CONTROUS 5 x ccscudsnacesianpmacseseehue sd 13 FACTORY DEFAULT SETTINGS scsicusccsacenssaraitsatsavantaneannnas 13 OPERATION USING THE VISO FIVE AUDIO SETUP MENU 00000s 14 AUDIO SETUP MENUS ruaro E ose esameal nena na aiene nen 4 LISTENING MODE 2 acsossuuniusnsrntn de sassntninsa vide mesabanecen 4 INPUT SET MIN Giza sccssvsscssssleinuetshe saa dea ei n ein N EEEO 5 SPEAKER SETTINGS nasite enoa aE deen LARES AEEA 6 SREAKER DISTANCE Errera a a a e aE 6 CHANNEEEVENS eiut iE EEEE EEA AOT 6 USING THE VISO FIVE VIDEO SETUP MENU 0000 18 VIDEO SETUP MENU arcs ciecaiuccaas aneldteteasg ER EETA ER 8 DISC VIDEO anir rana En ERE
19. is used for controlling external equipment that is equipped with a 12V trigger input This output will be 12V when the VISO FIVE is ON and OV when the unit is either OFF or in standby CABLE SAT amp VCR Connect to these inputs S Video composite video and analog audio from source components such as cable TV decoders satellite tuners another DVD player or other applicable ancillary devices VCR may be used with recording components such as videocassette or DVD recorders Connect the VCR OUT audio video to these components corresponding audio video input Note that VCR may freely be used for play only components in which case their OUT jacks would remain unconnected 10 Downloaded From Disc Player com NAD Manuals 4 MONITOR S VIDEO VIDEO Connect to video input of a monitor television using quality dual RCA and or S Video cables designed for video signals In general the S Video connection is superior and should be used if your TV monitor provides the corresponding input COMPONENT VIDEO IN COMPONENT VIDEO OUT Connect the Component Video IN to Component Video outputs from compatible source components typically a DVD player and terrestrial or satellite HDTV tuner Connect Component Video OUT to the Component Video input of a compatible video monitor TV Be sure to observe consistency in connecting the Y Cb Pb Cr Pr jacks to the corresponding sources inputs SCART RGB OUT SCART RGB OUT video monitor TV SCA
20. larger room more like a concert hall or movie theatre STEREO All output is directed to the front left right channels Low frequencies are directed to the subwoofer if one is present in the Speaker settings Select Stereo when you wish to listen to a stereo or monaural production such as music CD or FM broadcast without surround enhancement Stereo recordings whether in PCM digital or analog form and whether surround encoded or not encoded are reproduced as recorded Multi channel digital recordings Dolby Digital and DTS are reproduced in Stereo Downmix mode via the front left right channels only as Lt Rt left right total signals The following Listening Modes require a specially encoded signal that must be present in digital format to be decoded by the VISO FIVE These modes are automatically switched on when the appropriate data stream is detected The desired data stream must sometimes be selected in the setup menu of the source media DOLBY DIGITAL Dolby Digital is the multi channel digital signal format developed in the Dolby laboratories Discs bearing the double D symbol were recorded with up to 5 1 channels of digital signals reproducing a much better sound quality with dynamic and spatial sound sensations that are much better than in the previous Dolby Surround DYNAMIC RANGE CONTROL DYN RANGE You can select the effective dynamic range subjective range from soft to loud for playback of Dolby Digital sou
21. navigation controls TO VIEW VIDEOS OR PHOTOS LOADED IN YOUR iPod Videos or photos uploaded in your iPod can be viewed directly via the VISO FIVE The following are the steps 1 Make sure that the TV Out setting of your iPod s Video or Photo Settings menu is at On mode and appropriate TV Signal is chosen 2 Video or photo file selection and playback procedures are managed directly from your iPod player or at Simple Mode 3 With the iPod IPD 1 dock s S VIDEO OUT and AUDIO OUT ports connected to the VISO FIVE s VCR input or to any other assignable input you can now directly enjoy via VISO FIVE your video or photo selections as uploaded in your iPod Make sure that you select the correct source input of the VISO FIVE NOTE iPod player functions features and playback capabilities accessible through VISO FIVE may vary depending on your iPod player model Check NAD IPD 15 specifications with regards to specific iPod models it supports iPod is a trademark of Apple Inc registered in the U S and other countries 29 OPERATION DEVICE SELECTOR m gt 2 Zz z SO 2 lt fe a MODI a EY 30 Downloaded From Disc Player com NAD Manuals USING THE HTR 7 REMOTE CONTROL SPECIFICATIONS e Controls up to 8 devices e 44 function keys e Learns up to 352 commands e Records up to 44 macros with a maximum of 64 commands each Co
22. now carry out the VISO FIVE to receive DAB broadcasts 1 Toggle AM FM DB button until DAB mode When DAB mode is selected VFD will show DAB initialize Please wait and then go to Full Scan mode FULL SCAN will enable the scanning of the full range of digital frequencies Band Ill and L Band This sequence cannot be interrupted The arrows show the progress of the sequence When scanning is completed the last number shown on the upper right side of the VFD corresponds to the total number of DAB broadcast stations found Then the first station is tuned in See ALPHANUMERIC description below to understand the order or arrangement of stations 2 The strength of the incoming signal can be shown on the VFD by pressing the ENTER button The more o segments visible in the lower display line the stronger the signal By changing the position of the antenna you can increase the signal strength Consult an antenna professional for more information NOTES No stations Available will be shown in the VFD when no DAB stations are found after the scanning process If this occurs check the connection and position of the DAB antenna or call your local DAB broadcast providers for coverage information When using HTR 7 buttons to navigate DAB options ensure that the DEVICE SELECTOR setting of your HTR 7 is set to TUNER SERVICE LIST Follow the steps below to select through the DAB service stations foun
23. of the building as close to the point of cable entry as practical _ a BA ee 4 pee GROUND CLAMP B N power unes lt A STAND OFF b N ST INSULATORS mallina SERVICE adi P4 ENTRANCE CONDUCTORS a gt MAST SS ff ANTENNA SERVICE ENTRANCE GROUND CLAMPS Sf LEAD IN WIRE N GROUND WIRE gt g mm pee p gt S a 5 lt POWER SERVICE GROUNDING fo ELECTRODE SYSTEM ANTENNA DISCHARGE ONT GROUND e g interior metal water pipe BONDING JUMPER WIRE A gt TOEXTERNAL GROUND TERMINALS CLAMPS OF PRODUCT OPTIONAL ANTENNA GROUND C TRODE DRIVEN 8 FEET 2 44M INTO THE EARTH IF REQUIRED BY LOCAL CODES SEE NEC SECTION 810 21 f 15 Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 16 Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal 17 Overloading Do not overload wall outlets extension cords or integral convenience
24. or highlighted in the VFD alongside the playback time display Rpt Repeat track file or song RpA Repeat all tracks files or songs in an album or playlist Rpf Repeat MP3 WMA JPEG folder Blinking T Repeat DVD title Blinking C Repeat DVD chapter Blinking G Repeat DVD Audio group SLOW Zoom LEARN O VOL RANDOM r AA Press SLOW A during playback The player will enter SLOW mode Repeatedly press SLOW A to select the desired speed To exit Slow Motion mode press PLAY STILL PICTURE AND FRAME BY FRAME PLAYBACK TONE Press II PAUSE on the remote control or PLAY PAUSE on the front panel during playback Advance the picture frame by frame by pressing I on the HTR 7 repeatedly To exit still motion mode press gt PLAY 22 Downloaded From Disc Player com NAD Manuals ZOOM ocrur TV VIDEO ZOOM a LEARN VOL RANDOM Use ZOOM to enlarge the video image Press ZOOM during playback or still playback to activate the Zoom function Depending on the media each press of the ZOOM button changes the TV screen in the following sequence ZOOM X 1 ZOOM X 2 and ZOOM X 3 Use the HTR 7 A lt keys to move through the zoomed picture To resume normal playback press ZOOM repeatedly until ZOOM OFF NOTE Zoom may not work on some DVDs PROGRAMMING gt 00 00 07 461148 ff Track16 cDA Tracko9 W Track10 S Track1
25. that you are at View Browser as set up from the View Filter section Press lt 4 to go to the left pane of the menu screen Press ENTER or gt Play to resume normal playback PLAYING MP3 WMA JPEG The VISO FIVE can play MP3 WMA formatted recordings on CD R or CD RW discs as well as view discs with JPEG files You may mix any of the file types on the disc Load the applicable disc The OSD will display the folders or files as a list Use the HTR 7 s A W lt 4 P keys to navigate through the folders or files You must be at stop mode to access folders on the left side of the menu window Press ENTER or PLAY to start playback For each file type being played the file number is preceded by M W or J to indicate the file being played is a MP3 WMA or JPEG file ROTATE PICTURE Press A W lt 4 keys during the showing of a picture to rotate the picture 90 180 270 and back to No rotation original normal position Downloaded From Disc Player com NAD Manuals OPERATION USING VISO FIVE FEATURES TIMER SETUP The following are the steps on how to setup the internal clock of the VISO FIVE setup the time you wish the VISO FIVE to be switched ON from standby mode ON TIME or go to standby mode OFF OFF TIME 1 Press and hold the front panel TIMER ON OFF button for more than 4 seconds TIME is displayed in the VFD along with the current clock settings the hour value is blink
26. to blue Place a disc on the disc tray with the playback side down There are two different disc sizes Place the disc in the correct guide on the disc tray If the disc is out of the guide it may damage the disc and cause the VISO FIVE to malfunction DISC Err appears on both the VISO FIVE s display and the TV monitor screen if the disc is placed upside down and it is a single sided disc The following are important tips when loading a disc Do not push the disc tray while it is moving Doing so may cause the VISO FIVE to malfunction e Donot push up the disc tray or put any objects other than discs on the disc tray Doing so may cause the VISO FIVE to malfunction e Keep your fingers well clear of the disc tray as it is closing Be especially careful with children s fingers around the closing disc tray as there is a risk of personal injury Press PLAY PAUSE the disc tray is automatically closed and playback begins Press the HTR 7 s navigation buttons and then press ENTER or press the numeric button s to select the desired track CD Play of the selected item now begins Depending on the DVD disc or other disc media some operations may be different or restricted Refer to the jacket or case of the disc you are playing Press the HTR 7 s STOP key twice during playback to display an audio CD s total number of tracks and total playback time in the VFD After playing back all of the chapters in the title VISO F
27. 1 Add to Program Track12 Track13 Trackt4 Al tracks a Track16 Music Playing The program function enables you to store your favorite tracks in the player memory When programming a sequence of tracks the VISO FIVE must be in stop mode A program can contain up to 30 tracks To program the sequence 1 Insert a disc Audio CD or MP3 WMA discs CD or MP3 WMA menu appears 2 Use gt to go View Filter right pane of the menu screen 3 Use W to scroll down to Prog Edit Off Press ENTER to change setting to Prog Edit On Press W to check if you are at View Browser mode if set to View Program mode press ENTER to switch to View Browser mode 4 Press lt 4 to go to the track selection on the left pane of the menu screen Select the track file you want to add in your program list and hen press ENTER a mark will appear to the left of the selected rack 5 Press gt to go back to the right pane of the menu screen Use Y to scroll down to Add to Program press ENTER to add the selected track in your program list 6 Repeat steps 4 and 5 to place additional tracks files on the list 7 Set Prog Edit On to Prog Edit Off in order to complete the programming procedure use A to scroll to Prog Edit On and hen press ENTER to change the setting to Prog Edit Off NOTE Program mode can
28. 5170 5240 5340 602 1512 1531 T532 1571 1572 203 5325 603 L70 L73 DVD 204 5060 604 L56 7513 1514 1515 1524 a m ga T533 1534 300 Tuner 606 L53 DVD SEARCH MODE If none of the codes from the table when entered turns on the component and if you are quite sure you have followed the above procedure completely and carefully you may want to try the search method as follows Enter Library Mode by simultaneously pressing and holding for 3 seconds both the desired Device Selector key and the PROGRAM button until the Learn LED turns green Now press and hold the HTR 7 s A key the remote will step through all the available codes at a rate of approximately 1 per second Downloaded From Disc Player com NAD Manuals OPERATION USING THE HTR 7 REMOTE CONTROL When the component turns off immediately release the cursor key press ENTER to accept that code library and exit the Library Mode Try a few commands should you prove to have stepped past the needed code library re enter the Library Mode and use the cursor key to step back to it NOTE It is possible that search mode will find code libraries that operate at least partially some other brand non NAD components You may certainly exploit such capabilities as you find them However since we can only ensure the completeness or accuracy of NAD code libraries we cannot support the HTR 7 s operation with other brand components CHECKING CODE LIBRARY NUMBER
29. Be sure that you remain in the primary listening position while balancing all channels To produce the same SPL meter reading or subjective loudness use the remote s lt gt keys to adjust each speaker NOTES All speakers must be in their final locations before level setting Your subwoofer if any should be set with its integral crossover defeated or if undefeatable set to its highest possible frequency if you are using the VISO FIVE s Subwoofer output Final subwoofer level adjustment by ear using music and film sound material is frequently useful Due to the effects of room acoustics matched pair speakers front surround will not always calibrate to exactly the same level offset readings You can exit Test mode at any time by pressing the HTR 7 remote s Test 17 Downloaded From Disc Player com NAD Manuals OPERATION USING THE VISO FIVE VIDEO SETUP MENU VIDEO SETUP MENU Disc Video Disc Audio Disc Language Parental Control DivX Setup Exit DISC VIDEO Format Wide Screen 16 9 Signal Mode PAL HDMI Res Auto Brightness Basic Sharpness Basic Video Output Do not Save amp Exit Save amp Exit Component FORMAT Set FORMAT to select a picture size matching the aspect ratio of your TV Monitor Select Pan Scan 4 3 or Letter Box 4 3 when a standard 4 3 TV is connected Letter Box 4 3 Displays a wide picture with bands on the upper and lower portion
30. E EARE TEE RN 8 HDMI RES RESOLUTION sxcicscicapxnnscudenmedscntas aii 8 DISCADOR 9 DISC LANGUAGE sn enore EEE ETA 9 PARENTAL CONTRO ois cieisis ow sinaitea s eacnneieigrolg ow sieaulaaidinmoneisiealsess 9 DIVX SETUP cistron iiien ERER E AEE been cues 20 OSD LANGUAGE duri E eeN ERENER EE EREET VER 20 USING VISO FIVE FEATURES cccceceeceeceeseeneeeees 21 ABOUT THE VISO FIVE INTERNAL DVD PLAYER 000 2005 21 REGION MANAGEMENT INFORMATION 0000000 eee 21 DISC LOADING AND PLAYBACK nrcsecrsro timore eire aa 21 HILEANOMENU BUTTONS csi dusweuaasdosmndaink dna ein iiai 21 RANDOM eirese niran A A A a a e 21 REPEAT sctassrsrerectansieiace steren hputenadtenca A E A ETENEE 22 IOW ar EEEE r E E E ES 22 STILL PICTURE AND FRAME BY FRAME PLAYBACK 22 THANK YOU FOR CHOOSING NAD The VISO FIVE DVD Surround Sound Receiver is a technologically advanced and highly capable product yet we have invested great effort in making it simple and easy to use The VISO FIVE delivers a range of genuinely useful options for surround sound and stereo listening using powerful digital signal processing and superbly accurate digital audio circuitry However we have also been careful to ensure that the VISO FIVE is as musically transparent and spatially accurate as possible incorporating much of what we ve learned from a quarter century s experience designing audio and home theater components As with all our prod
31. ESHOOTING SPECIFICATIONS ccc ccc cece nS T E E We encourage you to take a few minutes now to read right through this manual Investing a little time here at the outset might save you a good deal of time later and is by far the best way to ensure that you make the most of your investment in the NAD VISO FIVE and get the most from this powerful and flexible home theater component One more thing We urge you to register your VISO FIVE ownership on the NAD Worldwide Web site http NADelectronics com warranty For warranty information contact your local distributor INTRODUCTION ABOUT VISO FIVE Though the VISO FIVE is among the most technically sophisticated DVD Surround Sound Receivers we worked hard to make it one of the most musically transparent home theater components available as well this is what we mean by NAD s Music First design philosophy Here are just few examples e High performance components used throughout VISO FIVE s analog audio circuits to maximize quality from all sources including multi channel analog sources such as DVD Audio e The VISO FIVE has exceptional playability It has support for DVD Video DVD R RW R RW DVD A SVCD with or without PBC Play Back Control VCD DivX Audio CD CD R RW and including recorded MP3 copyright protected WMA and JPEG flles e An RS 232 port for advanced zone control and software update through a Windows compatible PC e Gold surfaced connec
32. However in order for the HTR 7 to control your specific NAD brand components you may need to load one or more different code libraries see Loading Code Libraries below CONTROLLING THE VISO FIVE The HTR 7 is divided into two main sections Eight Device Selector keys at the top AMP DVD TV and so on set the handset s remaining keys to a page of commands to control a particular component A Device Select key determines only what component the HTR 7 will command it does not perform any function on the VISO FIVE All of the remaining keys are function keys that can learn control codes from virtually any infrared remote controller allowing you to teach the codes of your equipment regardless of brand to the HTR 7 However the HTR 7 is already preprogrammed to operate the VISO FIVE All of the function keys on the AMP Device Selector page perform VISO FIVE functions The HTR 7 can also command many other AD components from its DVD CD TUNER and CUSTOM pages tis important to note that certain HTR 7 keys perform different functions depending on the selected Device Selector page The color of the Device Selector key labeling corresponds to the labeling of he function keys Most centrally the orange AMP Device Selector page corresponds to the orange input select labeling above the numeric keys When the HTR 7 s AMP Device Selector page is active hese keys select the Viso Five inputs Sim
33. IVE s DVD player automatically stops and returns to the menu screen NOTES Do not move the VISO FIVE during playback Doing so may damage the disc and the VISO FIVE The HTR7 control keys 11 I K4 lt 4 gt gt 1 lt lt gt gt and gt are not punch through function keys To use them for disc playback purposes make sure that HTR 7 s DEVICE SELECTOR is set to DVD Downloaded From Disc Player com NAD Manuals OPERATION USING VISO FIVE FEATURES Depending on the media the following are other basic features of the VISO FIVE s internal DVD player Make sure that you select DVD at the Device Selector selection of the HTR 7 before you proceed with the specific function TITLE AND MENU BUTTONS NS WSJ ASO TUNER Both these buttons are only found on the HTR 7 The TITLE and MENU buttons are used to display via OSD the title headings and menus of the DVD and other applicable media Some movie discs may contain two or more titles If the disc has a title menu recorded on it the TITLE button can be used to select the movie title The details of operation differ depending on the disc used Press TITLE and a list of the titles on the disc are displayed Depending on the disc pressing TITLE again will resume play from the scene when TITLE was first pressed Press ENTER PLAY or the numeric button s to select desired title the selected title now starts playing Some DVDs ha
34. RT RGB plug Disc Video menu RESET In the unlike hangs up press th RS 232 Connect Euro model PAL only Connect the VISO FIVE s o the SCART RGB video input of a compatible Be sure to observe the correct orientation of the ake sure also to set Video Output to RGB at the or stable video at SCART RGB OUT y event that the VISO FIVE becomes inoperable or is button to reset the VISO FIVE his interface via RS 232 serial cable not supplied to any Windows compatible PC to allow remote control of the VISO FIVE through NAD s proprietary PC software or other compatible external controllers NAD is a certified partner of AMX and Crestron and fully supports these external devices See your NAD audio specialist for more information SUBW SUBWOOFER PRE OUT Connect this output to a powered active subwoofer or to a power amplifier channel driving a passive system 10 LOAD SW For future software program updates use this button in combination with RS232 to upgrade the VISO FIVE Owners who register their VISO FIVE in our international website www nadelectronics com will be advised of updates Your custom installer or dealer can assist you in the proper upgrade and setup of your VISO FIVE 1 5 1 CH INPUT Connect to the corresponding analog audio outputs of a multichannel source component such as a DVD Audio or external multichannel decoder disc copy protected formats only allow analog signal tran
35. TANT INFORMATION FOR UK CUSTOMERS DO NOT cut off the mains plug from this equipment If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point then obtain an appropriate safety approved extension lead or consult your dealer If nonetheless the mains plug is cut off REMOVE THE FUSE and dispose of the PLUG immediately to avoid possible shock hazard by inadvertent connection to the mains supply If this product is not provided with a mains plug or one has to be fitted then follow the instructions given below IMPORTANT DO NOT make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol or colored GREEN or GREEN AND YELLOW The wires in the mains lead on this product are colored in accordance with the following code BLUE NEUTRAL BROWN LIVE As these colors may not correspond with the colored markings identifying the terminals in your plug proceed as follows The BLUE wire must be connected to the terminal marked with the letter N or colored BLACK The BROWN wire must be connected to the terminal marked with the letter L or colored RED When replacing the fuse only a correctly rated and approved type should be used and be sure to re fit the fuse cover IF IN DOUBT CONSULT A COMPETENT ELECTRICIAN NOTES ON ENVIRONMENTAL PROTECTION At the end of its useful life this product must not be disposed of with regu
36. VD SECTION SYSTEM OUTPUT PHYSICAL SPECIFICATIONS Manufactured under license from Dolby Laboratories trademarks of Dolby Laboratories The XM name XM Ready and related logos are registered trademarks of XM Satellite Radio Inc Downloaded From Disc Player com NAD Manuals Dolby Pro Logic and the double D symbol are registered HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC IM distortion at rated power Damping factor 8 Q Input sensitivity and impedance Frequency response Signal noise ratio Signal noise ratio Tuning range Usable sensitivity S N ratio Total Harmonic Distortion Tuning range Usable sensitivity MONO S N Ratio MONO S N Ratio STEREO Total Harmonic Distortion MONO Total Harmonic Distortion STEREO Channel Separation RDS decode sensitivity Signal system Laser CD DVD Frequency response Signal to noise ratio audio Dynamic range audio Total Harmonic Distortion Video ou S video Y signa S video C signa Component Y signa Component Cb Cr signa SCART RGB signal HDMI Audio Video Ou Digital out coaxial Digital out optica Dimensions W x Hx D Net Weigh Shipping Weigh ote Dimensions include feet volume knob and extended speaker terminals Specifications are subject to change without notice For updated documentation and features please log onto www NADelectroni
37. VD mode the VISO FIVE will automatically shut down and go to standby mode if it is left at NO DISC status for 8 minutes 23 OPERATION USING THE VISO FIVE AM FM DB iPod LISTENING TO AM FM RADIO The VISO FIVE s internal AM FM tuner offers very high quality sound from radio broadcasts The reception and sound quality will always be dependent to a degree however on the type of antenna s used as well as proximity to the broadcast origin geography and weather conditions ABOUT ANTENNAS The supplied ripbon wire FM antenna can be connected to the rear panel FM antenna input using the included balun adapter and should be fully extended to form aT This folded dipole antenna will usually work best when oriented vertically with the arms of its T fully outstretched and arranged perpendicular to the origin of the desired broadcast There are no rules however and experimenting freely with antenna placement and orientation may yield the clearest sound and lowest background noise In areas of poor FM reception an exterior FM antenna can improve performance dramatically If radio listening is important to you consider consulting an antenna installation professional to optimize your system The supplied AM loop antenna will usually provide adequate reception However an exterior AM antenna can be used to improve reception Consult an antenna professional for more information ASSEMBLING THE LOOP ANTENNA gt
38. a n aa A EE sae 26 DYNAMIC RANG E origo eo E E E 27 TUNE AIDE sis tippade EE E EEA ONENE 27 PRUNE HIST iissa reani Dea T a Ea 27 NFORMATION SET TUNG Si 2 cxcieecs piniienn E ENEE 27 ABOUT AMRA DIO E n nn EE E AAE EA 28 ABOUT THE iPod INPUT FEATURE 0 ceceeeee eee e eee e ee 28 CONNECTING THE OPTIONAL NAD IPD 1 DOCK WITH iPod AND iPod PLAYER TO THE VISO FIVE 0 00eeee eee eee 28 iPOD MENU OPTIONS wxis5 cccoawadl cciocematandeemsatnnaancaoancsines 29 CONTROL FEATURES 3 5 sahisasadatiiet sadoatiad Sadadtiast une doae ds 29 TO VIEW VIDEOS OR PHOTOS LOADED IN YOUR iPod 29 USING THE HTR 7 REMOTE CONTROL 00 cece eceeeeeeee 30 SPECIFICATIONS ctesiatamantranean mgaeeniaoneee eda caw enaanele 30 CONTROUEING THE VISOSPIVE concise cisteuiemaiadisidieetscinndie simhainnasicie 30 LEARNING CODES FROM OTHER REMOTES 000 00000 31 PUNCH TIFIROUGH eaire iia snio ea E EEEE 31 COPY COMMAND FROM ANOTHER BUTTON 00055 31 AGRO COMMANDS cin rensar pan auernda wars lagle Meola Semele aed 31 BUTTON ILLUMINATION TIMEOUT 00 32 FACTORVIRESER s scociaasitedsdeetbr techies sucears iredismdes abbot eae seaties 32 DELETE MOD Errors Ganson cin tinamacmatees ca ANEA 32 LOADING GODE LIBRARIES icsi sanson 33 SEARCH MODE cx cogs Sere pitte cttn Sein eae sais EATE 33 CHECKING CODE LIBRARY NUMBER nn osnsinussssrirererssrrren 33 SLEEPMODE arena orire E T EE E TOATDA 33 REFERENCE TROUBL
39. ally deleted when OK SELECT is selected Otherwise select Cancel Downloaded From Disc Player com NAD Manuals OPERATION USING THE VISO FIVE AM FM DB iPod INFORMATION SETTINGS While listening to a DAB broadcast the type of information displayed in the lower line of the VFD can be varied Toggle front panel s DISPLAY button to step through the following display options Program Type 4 Station Name 4 Time and Date 4 Audio Signal information 4 Channel and frequency 4 Signal Q 4 Software version PROGRAM TYPE This is a description of the type of broadcast supplied by the station such as Pop Rock Drama and the likes STATION NAME The name or identification of the DAB broadcast station is shown TIME AND DATE The current time and date as supplied by the DAB station are displayed AUDIO SIGNAL INFORMATION Displays the bit rate and audio type stereo mono or joint stereo as transmitted by the DAB broadcast provider These are set by the broadcaster to suit the type and quality of material being transmitted CHANNEL AND FREQUENCY The channel and frequency of the currently tuned DAB broadcast are displayed SIGNAL QUALITY This displays the digital error rate 0 to 99 of the currently tuned channel the lower the figure the better the quality of the received broadcast SOFTWARE VERSION Show the version number of the installed software 27 OPERATION USING THE VISO FIVE
40. at power ON state rotate INPUT SELECTOR knob to select iPod source The upper line of the VFD will show iPod NOTE When the iPod player is removed from NAD IPD 1 the lower line of the VFD will briefly show Disconnected Dock your iPod player into the NAD IPD 1 and the lower line will briefly show Connected iPod MENU OPTIONS There are two menu options for iPod Menu mode and Simple mode At Menu mode iPod navigation will be done and guided through the VFD of the VISO FIVE At Simple mode everything will be guided through your iPod s own display screen as you would do in normal iPod use Menu mode is the default menu option The following is the procedure to switch between Menu mode and Simple mode options 1 Press and hold front panel s MENU button or MENU TUNER MODE key of HTR 7 for about 3 seconds and then release the button 2 Menu mode or Simple mode will appear You are at Menu mode if the lower line of the VFD briefly shows Connected and then switches to display the elapsed time and remaining playback time of the current song You are at Simple mode if the lower line of the VFD shows the current listening mode i e PLII Music Select your preference by releasing the button when the mode you desire appears MENU MODE At Menu mode there are several menu options available that are similar to what you can find in an iPod player During playback p
41. band 2 Press and hold the MEMORY button until the station frequency indication begins to increase 3 Release the button and note that the tuner will search the entire FM or AM band and stop briefly at each station that has acceptable signal strength The VISO FIVE will automatically assign a preset number to each station and then search for the next station Up to 30 of the best received FM stations or AM stations will be automatically stored DELETING A STORED PRESET You can empty a preset by deleting the stored information 1 Select the preset number to be entered 2 First press the DISPLAY button and hold it in While holding in the DISPLAY button press the MEMORY button for about half a second then release the MEMORY button The preset will then be deleted and DELETED scrolls on the display To clear all the presets at the same time repeat step 2 again but this time do not release the MEMORY button Hold down both buttons until the current preset number shown in the VFD is extinguished All presets are now deleted A w CHOOSING TUNER MODE The front panel TUNER MODE key is a dual purpose control In the normal position FM STEREO and FM MUTE icons on the VFD are lit only the stations with a strong signal can be listened to and the noise between stations is muted Pressing the TUNER MODE button again FM STEREO and FM MUTE icons on the VFD are extinguished allows distant and p
42. cs com for the latest information about VISO FIVE DTS Inc All Rights Reserved 2x 60W 2x 80W 2x 120W 5x45W 0 08 0 08 gt 60 300 mV 47kO REFERENCE SPECIFICATIONS 0 5 dB ref 20Hz to 20kHz gt 100 dB ref rated power 80 A WTD gt 85 dB ref 1W 8Q A WTD 522kHz 1620k z Europe version 9kHz steps 530kHz 1710kHz North America version 10kHz steps 60 dBu 40 dB 15 87 5MHz 108MHz 10 dBu 70 dB 65 dB 0 3 0 3 50 dB 0 2 PAL NTSC Auto Two wavelength laser diode Wavelength 790nm Wavelength 650nm 0 5 dB ref 20Hz to 20kHz 100 dB A WTD 95 dB A WTD 0 02 1Vp p 750 1Vp p 750 0 286 Vp p 750 1Vp p 750 0 7Vp p 750 0 7Vp p 750 Ver 1 0x1 0 5 Vp p 750 15 dBm 21 dBm 435 x 135 x 370 mm 12 6 kg 15 6 kg anufactured under license under U S Patent s 5 451 942 5 956 674 5 974 380 5 978 762 6 226 616 6 487 535 amp other US and worldwide patents issued amp pending DTS DTS Digital Surround and ES are registered trademarks and the DTS logos Symbol and DTS 96 24 are trademarks of DTS Inc 1996 2007 Official DivX Certified product Plays all versions of DivX video including DivX 6 with standard playback of DivXx media files DivX DivX Certified and associated logos are trademarks of DivX nc and are used under license This product incorporates copyright protection technology that is protected by method claims of certain U S pa
43. d 1 At DAB mode press TUNE lt gt to step through the list of available stations as shown in the lower display line of the VFD 2 Press ENTER to select the desired station DAB TUNER MODE Aside from Full Scan as already described above pressing the MENU button will also present you with other options namely Local Scan Preset Tune Station Order Tune Aid Dynamic Range and Prune List LOCAL SCAN LOCAL SCAN performs local scanning of available DAB services in your area Check with your dealer or visit www WorldDAB org to check the applicable digital transmission frequencies in your area 1 While listening to a DAB broadcast press front panel s MENU button and then TUNE lt gt to select Local scan Press ENTER 2 Local scan of available DAB services in your area will start The arrows show the progress of the sequence When scanning is completed the last number shown on the right side of the VFD corresponds to the total number of DAB broadcast stations found Then the first station is tuned in 26 Downloaded From Disc Player com NAD Manuals PRESET TUNE Use this option to select a DAB preset station 1 While listening to a DAB broadcast press front panel s MENU button and then TUNE lt gt to select Preset tune Press ENTER 2 Press TUNE lt gt to step up or down between presets Note that Presets must have been previously stored 3 Press ENTER to select desired preset nu
44. d DO NOT STARE INTO BEAM FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Downloaded From Disc Player com NAD Manuals FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment INDUSTRY CANADA REQUIREMENT This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulati
45. d Select Exit in the password menu screen to exit the sequence if you are unable to enter the correct password 19 OPERATION USING THE VISO FIVE VIDEO SETUP MENU RATING LEVEL NORTH AMERICA VERSION ONLY Some movies contain scenes that may not be suitable for children to view Many of these discs contain parental control information that applies to the complete disc or to certain scenes on the disc Movies and scenes are rated from 1 to 8 depending on the country Some discs offer more suitable scenes as an alternative The RATING feature allows you to block access to scenes greater than the rating you have set up thereby preventing your children from being able to view material you believe is unsuitable To activate Rating please be guided by the following 1 While at Rating line menu press ENTER 2 Password___ _ will appear indicating that a password is needed to change the ratings level 3 Input the password you have setup at the Password item as discussed above Press ENTER 4 Upon entering the correct password you can now set the parental rating level you prefer Use lt gt to step through the rating levels 5 After you have selected your preferred rating level use W to scroll down to Save amp Exit option Press ENTER to save the rating level you have chosen RATING 1 8 Rating one 1 has the most restrictions and 8 is the least restrictive UNLOCK If yo
46. d pointing straight up toward the ceiling not toward the speakers and ensure that C weighting scale is selected Set the meter to display 75 dB SPL On Radio Shack meters this necessitates either setting the meter to its 80 dB range and taking your readings at the 5 point or selecting the 70 dB range and reading at the 5 point OPERATION USING THE VISO FIVE AUDIO SETUP MENU SETTING CHANNEL LEVELS IN TEST MODE While at Channel Levels menu press the HTR 7 remote s Test key activating the VISO FIVE s Channel Levels balancing test signal lower line of the VFD will show Test Tone You will hear a surf sound as you step hrough your speakers beginning with the Front Left If you do not hear the est signal check your speaker connections or your Speaker settings OSD menu settings Use the remote s lt gt keys to adjust the loudness of the noise output rom the currently playing channel to the required level it s usually simplest to begin with the Front Left As you cycle the test signal around he speakers the OSD will highlight the currently playing channel The level offset reading on the right will change by 1 dB increments 12 dB adjustment is available Press A to adjust the next speaker NOTE If you are balancing levels by ear choose one speaker usually the center as a reference and adjust each of the others in turn to sound as loud as the reference
47. d thus remains truer to the sound of the original musical performance than most other music surround options Select EARS for listening to stereo music recordings and broadcasts EARS produces a subtle but highly natural and believable ambience from nearly all natural acoustic stereo recordings Typically these include classical jazz and folk genres as well as numerous examples from others Its virtues include realistic stable front stage sonic imaging and spacious but unexaggerated ambient virtual acoustics that remain faithful to the original recording ENHANCED STEREO All recordings reproduced in stereo via the maximum speaker complement configured in the Speaker Settings menu Enhanced stereo can be useful for maximum volume from all channels or for multi speaker background music cocktail party listening For this mode Front Center and Surround can be turned On or Off as desired DOLBY VIRTUAL SPEAKER DVS Dolby Virtual Speaker technology creates a highly compelling 5 1 channel listening experience from as few as two speakers making it an ideal entertainment solution for locations where space for multiple speaker setups is limited Dolby Virtual Speaker models the sound of a playback system into two different listening environments based on acoustic measurements of real rooms DVS Reference is a small well damped room appropriate for both movies and music only recordings DVS Wide is a
48. e full procedure 32 Downloaded From Disc Player com NAD Manuals DELETE MODE The HTR 7 can store learned copied and default library commands on any single key The default library commands are the pre programmed NAD codes such as the native VISO FIVE commands on the AMP page You can delete commands by layers back down to the default library command on any key removing learned commands punched through functions and copied keys NOTE The default library commands cannot be deleted so you need not worry that using Delete Mode might cause irreparable changes To enter Delete Mode simultaneously press and hold for 3 seconds both the desired key s Device Selector key and the RTN key until the Learn LED turns green Press the function key whose command you wish to delete the Learn LED flashes the number of times indicates which type of function has become active see the table below Press the active Device Selector key again to exit Delete Mode NOTE You may delete multiple function key commands on the same Device Selector page but to delete from more than one Device Selector page you must exit Delete Mode and then re enter it on the required page Flashes Command Type 1 Default Library Command 2 Copied Library Command 3 Learned Command LOADING CODE LIBRARIES The HTR 7 can store a different library of default NAD codes for each of its Device Selector pages If the original default library
49. e manufacturer s instructions and should use a mounting accessory recommended by the manufacturer A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn 10 Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 11 Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company The primary method of isolating the amplifier from the mains supply is to disconnect the mains plug Ensure that the mains plug remains accessible at all times Unplug the AC power cord from the AC outlet if the unit will not be used for several months or more 12 Grounding or Polarization This product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power out
50. edia overrides the settings Select among Original English French German Dutch Spanish Italian Russian and Swedish as the desired language setting If you do not want the disc s subtitles to be shown select Off PARENTAL CONTROL Parental Control Password Rating Level UNLOCK Do not Save amp Exit Save amp Exit PASSWORD PASSWORD is needed to gain access to the Rating Level below The following are the steps for you to enable or change your password 1 While at Password line menu press ENTER A menu screen like the one shown below will appear Parental Control Password Old Password Rating Level New Password Do not Save amp Exit Contirm Save amp Exit Exit 2 Input the 4 digit Old Password the preset Old Password is 2580 3 You can now set your own password by entering your desired 4 digit password at the New Password option Press ENTER 4 After entering your new password re enter again your new 4 digit password at the Confirm option Upon entering the correct password at Confirm option the password menu window will turn off bringing you back to Parental Control menu screen NOTE Ifthe password entered at Old Password or Confirm window is incorrect you will remain in the same menu item like Old Password or be returned to New Password You cannot move forward to the next sequence unless the correct password is entere
51. effectively defeating the effect of the tone control circuits If Tone Active is selected the Tone Control circuits are active Downloaded From Disc Player com NAD Manuals SETUP SETTING UP THE VISO FIVE FACTORY DEFAULT SETTINGS Sometimes power spikes and drop outs may from time to time cause some inadvertent functionality The procedure below will set the VISO FIVE to factory default settings 1 Place the VISO FIVE into AM mode 2 Press quickly the three front panel buttons PLAY PAUSE STOP then DISPLAY holding the DISPLAY button for more than 7 seconds The VISO FIVE will switch itself off then back ON to DVD mode Please note that setting the VISO FIVE to factory default will delete all AM FM and DAB presets It will also reset all your timer settings 13 OPERATION USING THE VISO FIVE AUDIO SETUP MENU AUDIO SETUP MENU Listening Mode Input Settings Speaker Settings Speaker Distance Channel Levels Exit LISTENING MODE Listening Mode Mode PLII Movie Do not Save amp Exit Save amp Exit The VISO FIVE offers distinct SURROUND MODES tailored for different types of recordings or program material With a two channel Stereo source the following listening modes can be selected PRO LOGIC PLII Dolby Pro Logic Il is a more recent evolution of the original Dolby Pro Logic surround processing that yields more stable imaging and full bandwidth sound to the rear channels in M
52. either to remember channel frequencies All broadcasts are selected by simply selecting the service name The VISO FIVE makes it possible for you to enjoy listening to DAB broadcasts The VISO FIVE has a Digital Audio Broadcast DAB module socket on the rear panel for adding a separately sold and NAD specified outboard DAB module the NAD DAB Adaptor DB 1 All the control software for this format is included just plug in the module and start enjoying the CD like quality sound and expansive content selection available with DAB CONNECTING THE DAB MODULE Plug in the other end of the DIN connector supplied with your NAD DAB Adaptor DB 1 from the DAB module s output port into the corresponding DAB module input socket on the rear panel of the VISO FIVE Select DAB mode on the VISO FIVE by toggling the AM FM DB button in the front panel NOTES Please refer to NAD DAB Adaptor DB 1 installation guide for proper setup connection of the DB1 with respect to the VISO FIVE The front panel TUNER MODE and MENU buttons function the same way at DAB mode The MENU TUNER MODE key of HTR 7 is the equivalent button for both functions If there is no NAD DAB Adaptor DB 1 connected at the corresponding DAB input terminal at the rear panel the VFD will show CHECK DAB TUNER 25 OPERATION USING THE VISO FIVE AM FM DB iPod DAB OPERATION With the separately sold NAD DAB Adaptor DB1 already connected to the VISO FIVE you can
53. em on SETTING RADIO PRESET under OPERATION USING THE VISO FIVE AM FM DB iPod discussions REMOTE SENSOR Point the HTR 7 remote control at the remote sensor and press the buttons Do not expose the remote sensor of the VISO FIVE to a strong light source such as direct sunlight or illumination If you do so you may not be able to operate the VISO FIVE with the remote control Distance About 23ft 7m from the front of the remote sensor Angle About 300 in each direction of the front of the remote sensor VACUUM FLUORESCENT DISPLAY VFD Provides visual information about the unit s important modes settings functions status of the current source like disc playback time and other indicators TIMER ON OFF In combination with PRESET kK gt gt I and MEMORY buttons press and hold or toggle to set the internal clock ON OFF timer as well as enable the timer modes Refer also to the item on TIMER SETUP under OPERATION USING THE VISO FIVE FEATURES discussions 10 FM AM DB Toggle this button to select either AM FM DAB Europe version or XM North America version tuner functions 11 TUNER MODE In FM mode this button will toggle between FM Stereo and FM mono Select FM Mono FM STEREO and FM MUTE icons at VFD are extinguished for stations that have too much interference or are too weak In DAB European version only or XM North America version only radio this button enables the digital radi
54. g VIDEO OUTPUT EUROPE VERSION MODEL ONLY Select between Component and RGB as your preferred video output media Make sure the appropriate video out of VISO FIVE is connected to the corresponding video input of your TV monitor RGB video setting is preferable if your output media is through SCART OUT At RGB setting video signal is split into three fundamental colors Red Green and Blue RGB resulting to greater picture resolution and elimination of artifacts associated with traditional composite video signals Select Component if you are not using SCART OUT as your output media DISC AUDIO Bitstream DVO Video Digital Out Disc Type PCM Format 9GKHZ Do not Save amp Exit Save amp Exit DIGITAL OUT Set VISO FIVE s Digital Out according to the type of audio system you use Bitstream Select Bitstream if you connect the VISO FIVE s digital OUT jack to an amplifier or other equipment with a Dolby Digital DTS or MPEG decoder PCM Select when connected to a two channel digital stereo amplifier DVDs encoded in Dolby Digital or MPEG will be automatically downmixed to two channel PCM audio DISC TYPE Some DVD Audio discs contain the DVD Video content in addition to the DVD Audio content You can choose DVD Audio or DVD Video mode depending on your preference DVD AUDIO Select to playback both DVD Audio and DVD Video contents DVD Audio content only may be played back depending on the disc
55. he jacks securely Power on the TV Unplug HDMI cable connected to rear panel s HDMI OUT At DVD mode and with no disc loaded NO DISC 1 Press and hold DISPLAY button The lower ine of the VFD will show the current HDMI resolution setting 2 Use the remote s lt P gt keys or toggle MEMORY button to select through 480P 576P 720P 10801 AUTO or OFF Select either 480P 576P or OFF to enable component video out composite and S Video output Stop at your desired resolution setting and release lt gt keys or MEMORY button e Clean the disc Insert a disc Insert a playable disc Check the disc type colour system and Regional code Place the disc with the playback side down Place the disc correctly inside the guide on he disc tray Press SETUP button of HTR 7 to turn off the menu screen Clean the disc Enter the correct password Set the VISO FIVE to factory default settings 1 Place the VISO FIVE into AM mode 2 Press quickly the three front panel buttons PLAY PAUSE then STOP then DISPLAY holding the DISPLAY button for more than 7 seconds The VISO FIVE will switch itself off hen back on to DVD mode Note Default password is 2580 AMPLIFIER SECTION Power output Stereo Mode IHF dynamic power 8 Q IHF dynamic power 4 Q Power output Surround Mode Total harmonic distortion at rated power TUNER SECTION AM SECTION FM SECTION D
56. ilarly the purple DVD Device Selector page corresponds to several purple labels the green TV page to green labels and so on SELECTING SOURCES To directly switch or select sources using the HTR 7 set first your DEVICE SELECTOR to AMP Press the corresponding numeric key of the source you want to select the orange label directly above the appropriate numeric keypad is the Source allocated for such key For example press 2 to select Cable Sat source mode 1 to switch to DVD mode and so on LEARNING CODES FROM OTHER REMOTES Begin by positioning the HTR 7 nose to nose with the source remote so the two devices infrared windows are about 2 inches apart e Enter Learning Mode On the HTR 7 simultaneously press and hold for 3 seconds both a Device Selector key and the 4 key until the Learn LED at the center of the HTR 7 turns steady green e Press the HTR 7 s function key you wish to teach a command the Learn LED will turn amber Press and hold the function key on the source remote The HTR 7 s Learn LED will flicker amber for a second or two then turn solid green The command is learned e Press the HTR 7 s Device Selector key again to exit the learning mode If the Learn LED does not flicker amber you may need to vary the distance between the remotes If the Learn LED turns red rather than green that particular command of that source remote command could not be learned
57. inals If your system includes a powered subwoofer connect the VISO FIVE s SUBWOOFER PRE OUT jack to its ine input Connect the AC cord to the AC inlet and then plug into an AC outlet he LED indicator around the POWER button will be illuminated amber indicating the VISO FIVE is in standby mode ready to accept commands rom either the front panel power switch or the HTR 7 remote e Press DVD at the HTR 7 remote s Device Selector section and then OPEN CLOSE button e Insert the media and press PLAY button to start playback You should hear sound from VISO FIVE and see an image on the TV monitor If one or the other fails to appear check your TV monitor s input settings or VISO FIVE s audio video connections Enjoy the movie or music but be sure to set aside time to read this manual thoroughly and to set up calibrate and configure your VISO FIVE carefully and completely IDENTIFICATION OF CONTROLS FRONT PANEL 8 9 10 11 12 13 F MENU DISPLAY MEMORY Tune Tune me CTY D i Loevere rea PRESET Ti CHS 6 12 45 Tolbu Digital TIMER AM FM TUNER ONOFF DB MODE TONE 0000 NAD Viso Five 1 INPUT SELECTOR Y L R MONO VIDEO SVIDEO Lauoiot p 21 20 POWER BUTTON Press this button or the HTR 7 remote s ON button to switch ON the VISO FIVE The Standby LED indicator will turn from amber to blue and illuminate the VFD Pressing the po
58. ing Use the PRESET 4 gt gt I buttons to change the hour setting 3 Press MEMORY button to move on to minute setting the minute value is blinking Use the PRESET IK gt gt I buttons to change the minute setting 4 Press MEMORY button to move on to ON TIME setting Follow steps 2 and 3 above to setup your preferred ON TIME hour and minute settings 5 Press MEMORY button to complete your ON TIME settings ON TIME YES will be displayed in the VFD Use PRESET 4 gt gt I buttons to oggle between ON TIME YES and ON TIME NO 6 Press MEMORY button to select either ON TIME YES to enable the ON TIME settings you have set up or ON TIME NO if you do not want to enable your ON TIME settings 7 OFF TIME is also setup the same way as that of ON TIME TIMER INDICATOR SETTINGS If you have selected ON TIME YES and or OFF TIME YES a corresponding color indicator will be illuminated in the upper left portion of the VFD GREEN indicates ON TIME setting is enabled RED indicates that OFF TIME setting is enabled To directly turn off the enabled timer setting s toggle TIMER ON OFF button the applicable color indicator is extinguished Toggle TIMER ON OFF button again to enable your timer settings the corresponding color indicator is illuminated again AUTOMATIC POWER OFF FUNCTION When at D
59. input in its upper line display ADJUSTING THE VOLUME In addition to the Volume knob use the HTR 7 s VOL A to adjust the master volume of the VISO FIVE raising or lowering the channels altogether A momentary keypress will change the master volume by 1 dB increments If you hold down VOL amp the master volume change will run on until the key is released Since recordings vary considerably in overall average level there is no imperative to listen at any particular master volume setting A setting of 20 dB may sound as loud from one CD or DVD as 10 dB does from another The VISO FIVE will power up from Standby mode at whatever master volume setting it was last used however if the prior setting was greater than 15 dB the VISO FIVE will power up at 15 dB This prevents inadvertently beginning a session at excessive volume MUTING THE SOUND Use the HTR 7 s MUTE key to silence all channels completely Mute is displayed in the lower line of the VFD Muting is always available regardless of the source or listening mode selections NOTE Adjusting the master volume via the HTR 7 or the front panel knob automatically releases the mute function ADJUSTING CHANNEL LEVELS ON THE FLY You can make changes to the relative levels of center surround and subwoofer outputs without having to go into the Channel Levels menu This is very convenient in circumstances like increasing or tone do
60. is it remains in force with all inputs and in all LISTENING MODES ENHANCED BASS When the subwoofer is set to ON and all speakers are set to Large Enhanced Bass is also available Normally with speakers set to Large the subwoofer is not active The Enhanced Bass option allows full range operation of the speakers with the additional bass contribution of the subwoofer This feature is particularly useful when one wants to experience maximum bass output Please note that due to acoustic cancellation effects the bass response may be uneven when using this setting You can set Subwoofer to On even with Large front speakers In such cases both subwoofer and front speaker will receive the LFE channel signal In the case where the front speakers are set to Small the LFE channel signal will be routed to subwoofer but not to the front speakers LFE channel signal will pass only to the subwoofer In most subwoofer equipped systems setting front speakers to SMALL is usually the better option 16 Downloaded From Disc Player com NAD Manuals SPEAKER DISTANCE Front Center Surround Distance Do not Save amp Exit Save amp Exit Setting the Distance lets the speakers know how far the sound has to travel to reach your set listening point This allows the sound from each speaker to reach the listener at the same time Distance can be adjusted within 1FT 0 30M up to 30FT 9M Distance setting is no
61. it powerfully easy to use Its design is uniquely simple for so sophisticated a component and the HTR 7 universal remote control is equally understandable as are the VISO FIVE s own front panel and on screen displays 6 Downloaded From Disc Player com NAD Manuals RS 232 Flexible system configuration is possible with the RS 232 interface and NAD s proprietary Windows compatible software We are also certified partners with AMX and Crestron and fully support these external devices This interface allows complete remote control of the VISO FIVE from any remote location via the PC Complete remote control functionality is available to the user by interface software See your NAD audio specialist for further information UPGRADABILITY The VISO FIVE permits flexible system growth We have made the more likely scenario of software upgrades easy to accomplish via the high speed RS 232 port on the rear panel and in combination with the LOAD SW switch also on the rear panel Owners who register their VISO FIVE on our international web site www NADelectronics com will be advised of updates Some of these may be free of charge and some may require royalty payments depending on the type of upgrade The advanced user will be able to perform these upgrades by downloading files from our web site via e mail and installing them by connecting the VISO FIVE to a PC Alternatively the dealer from whom you purchased your VISO FIVE should be able to
62. ital audio link to the VISO FIVE for audio playback This avoids possible confusion and ensures that the VISO FIVE s high performance digital audio circuitry will always be employed 15 OPERATION USING THE VISO FIVE AUDIO SETUP MENU SPEAKER SETTINGS Front Center Surround Subwoofer Enhanced Bass Do not Save amp Exit Save amp Exit Every surround sound system requires bass management to direct low frequency content from any or all channels to the speakers best able to reproduce it For this function to operate correctly it is important that you correctly identify your speakers capabilities We use the terms Large Small Mini and Off but note that physical size may be irrelevant A Small speaker is any model regardless of physical size that lacks significant deep bass response Set to SMALL if your speaker cannot handle lower than 100 Hz e A Large speaker is any full range model that is one with deep bass response Set to LARGE if your speaker can handle 20 Hz 20 kHz full frequency range Select Mini if your speaker cannot handle lower than 150Hz Set Subwoofer to On or Off selecting On only if you have a subwooder connected to VISO FIVE s SUBW output jack e An Off speaker is one that may be present such as a subwoofer but set to Off in the Speaker Settings setup menu The Speaker Settings is global that
63. lar household waste but must be returned to a collection point for the recycling of electrical and electronic equipment The symbol on the product user s manual and Sa packaging point this out The materials can be reused in accordance with their markings Through re use recycling of raw materials or other forms of recycling of old products you are making an important contribution to the protection of our environment Your local administrative office can advise you of the responsible waste disposal point NOTE THE VISO FIVE IS NOT AN AUTO VOLTAGE DVD RECEIVER CONNECT ONLY TO THE PRESCRIBED AC OUTLET I E 120V 60HZ OR 230V 50HZ RECORD YOUR MODEL NUMBER NOW WHILE YOU CAN SEE IT The model and serial number of your new VISO FIVE are located on the back of the cabinet For your future convenience we suggest that you record these numbers here NAD is a trademark of NAD Electronics International a division of Lenbrook Industries Limited Copyright 2009 NAD Electronics International a division of Lenbrook Industries Limited 4 Downloaded From Disc Player com NAD Manuals IMPORTANT SAFETY INSTRUCTIONS cceee cues 2 INTRODUCTION ABOUT VISO FIVE cscs cecce cee cee cee cee ceeeeesenneeeeeees 6 E A R S AND DIGITAL SURROUND eee eens 6 EASE OR USE tanrsiatearsannimurpaunnseereceamatesacuaieuoseseaat 6 RO 232 swan devndhnnsassesvanntisab rahe EAA n AER EE EREA ERAS 6 UPGRADABILITNG i veronii
64. le to permit a component to power up completely you can record empty steps into the macro by changing Device Selector pages without entering actual command functions BUTTON ILLUMINATION TIMEOUT The HTR 7 s key illumination can be set to remain lit for 0 9 seconds The default value is 2 seconds To set the illumination timeout simultaneously press and hold for 3 seconds both the HTR 7 s DISP and the 0 9 key with the digit corresponding to the desired timeout duration the Learn LED will flash twice to confirm the new setting When set to zero the illumination will not turn on at all NOTE Key illumination is the biggest drain on the HTR 7 s batteries A short key illumination timeout will extend battery life appreciably turning it off altogether set it to 0 seconds will lengthen it still further FACTORY RESET The HTR 7 can be reset to its factory state deleting all learned commands copied and punched through keys macros and other setup information reverting all keys to their pre programmed library commands To perform a factory reset simultaneously press and hold for 10 seconds the HTR 7 s ON and RTN keys the Learn LED will start to flash green Release ON and RTN before the second flash is complete the Learn LED will turn red indicating the remote has been reset NOTE You must release ON and RTN before the second flash goes out otherwise the unit will not reset should this occur repeat th
65. le to this socket Follow the instructions that came with your XM radio With XM radio there are more than 100 channels of music news sports comedy talk and entertainment You will find that the coverage is continent wide The music quality is digital with many commercial free music channels NOTE Questions Visit www xmradio com Listeners can subscribe by visiting XM on the Web at www xmradio com or by calling at the time of printing this manual XM s Listener Care at 800 853 9696 Be ready with your Radio ID that can be found on the radio by selecting Channel 0 DAB MODULE INPUT Europe version only Plug in the other end of the Mini Din connector from the NAD DAB Adaptor DB 1 module output port into this socket The VISO FIVE is compatible only with NAD DAB Adaptor DB 1 so check with your NAD dealer for this module s availability With DAB you can receive CD like quality programs without any annoying interference and signal distortion Downloaded From Disc Player com NAD Manuals 15 COAXIAL IN OPTICAL IN Connect to the optical or coaxial S PDIF IDENTIFICATION OF CONTROLS REAR PANEL format digital output of sources such as CD or DVD players HDTV or satellite tuners and other components OPTICAL OUT Connect the optical digital OUT port to the corresponding S PDIF digital input of a compatible device such as CD recorders receivers computer soundcard or other digital processors 16 FM AM ANTENNA INPUT The sup
66. let only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug 13 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product 2 Downloaded From Disc Player com NAD Manuals 14 Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer s attention to Section 820 40 of the NEC which provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system
67. lly scan the AM or FM band Press and hold for more than 2 seconds to search up or down the VISO FIVE s tuner will stop at the next sufficiently strong signal it encounters Note that this function too wraps and will continue searching up or down from one end of the AM or FM band to the other At DVD mode press PI to skip forward or I to skip backward a track file or chapter Press lt 44 gt gt during disc playback to select the desired scanning speed 8 Downloaded From Disc Player com NAD Manuals NAD VISO FIVE 19 18 17 16 15 14 When setting up the Timer use the k lt gt gt I buttons to change the hours and minutes MENU Press this button to bring up the DVD disc menu during DVD disc playback stop pause or stop resume mode At FM XM DAB mode the MENU button also functions the same way as that of TUNER MODE button See also TUNER MODE description below DISPLAY At TUNER mode toggle this multifunction button to display at the VFD relevant information of a currently tuned FM XM or DAB station At CABLE SAT VCR or Front source mode toggle DISPLAY button to select optical coaxial audio input or the assigned analog audio input of the particular source When in DVD mode toggle DISPLAY button to alternatively display the general disc playback status of the DVD display navigation menu MEMORY Use to store tuned stations to the VISO FIVE s preset memory locations Refer also to the it
68. mber SETTING DAB PRESETS The VISO FIVE can store as many as 99 DAB stations of your favorite DAB broadcast for immediate recall 1 Tostore a DAB preset first tune the DAB broadcast and then press the front panel MEMORY button The VFD will show a Preset Memory and the next available vacant Preset number the number is blinking 2 Press MEMORY button again to store the desired DAB broadcast on the Preset number shown or use the TUNE lt P gt keys to select another available Preset number 3 Then press MEMORY key button again Your desired DAB broadcast is now stored in the assigned presets STATION ORDER Use Station order to sort the sequence of the listed stations There are four orders Alphanumeric Active Ensemble and Favourite 1 While listening to a DAB broadcast press front panel s MENU button and then TUNE lt gt to select Station Order Press ENTER 2 Toggle TUNE lt P gt to select through Alphanumeric Active Ensemble and Favourite 3 Press ENTER to select desired station order ALPHANUMERIC This is the default setting Stations are arranged by numbers first and then alphabetically by letters ACTIVE Active stations are listed at the top of the channel list Those channels that are in list but have no service in the area will be displayed last in the channel list ENSEMBLE Digital radio is broadcast as groups of data called ensemble Each en
69. n be changed using the menu To use the on screen display 1 Press the HTR 7 s DISP during playback 2 Press lt gt to select an item The selected item is highlighted 3 Key in the desired the number button or press ENTER as applicable 00 10 07 19 4 37 11 3 DOD TF Eng FE 17 2 Eng P4171 NOTES The display feature may not be available for all disc media and is media dependent Display disc OSD does not apply to audio only discs like CD and MP3 WMA IPEG files as they are already presented in their respective menu screens The front panel and HTR 7 s DISP button toggles between title chapter time or group track time for DVD A discs and audio subtitle angle display configurations Ifno button is pressed for about 10 seconds the on screen display disappears SELECTING SOURCES You can choose your desired source by rotating the INPUT SELECTOR knob to select through the following Internal DVD gt Cable Sat gt VCR iPod gt Front gt AM FM XM DAB gt Ext 5 1 gt then back to Internal DVD The same source can be directly selected using the HTR 7 remote control 1 Set HTR 7 s DEVICE SELECTOR to AMP 2 Press your desired source s corresponding numeric keypad allocation The orange label directly above the appropriate numeric keypad is the Source allocated for such key example 1 for DVD 2 for CAB SAT and so on When you change sources the VFD will show the new
70. n remote or IR receiver window on VISO FIVE is obstructed VISO FIVE front panel is in very bright sunlight or ambient light Microprocessor error VISO FIVE may have over heated No disc is inserted The TV is not set to receive video signal The video cable is not connected securely The connected TV power is turned off HDMI connector is plugged in and HDMI Res is set to 720P 1080 or AUTO The disc is dirty No disc is inserted An unplayable disc is inserted The disc is placed upside down The disc is not placed within the guide A menu is on the TV screen The disc is dirty The password entered was wrong Password was forgotten POSSIBLE SOLUTIONS e Check AC cable connection and outlet Check cables Check speaker connections Check Speaker Settings menu Power up subwoofer check Sub s AC outlet or check connections Correct subwoofer level by adjusting SUB button at HTR 7 e Check batteries Check IR windows and ensure clear line of sight from remote to VISO FIVE Reduce sunlight room lighting Power down the VISO FIVE via the front panel Power switch and unplug it from the AC outlet Wait five minutes re connect and power up Insert a disc Select the appropriate video input mode on the TV so that the picture from the VISO FIVE appears on the TV screen output Connect the video cable into t
71. nal source key command the copied to key s command remains unchanged If you punch through to a command and then delete or over write the original key the punched through functions also change accordingly MACRO COMMANDS A macro command is a series of two or more remote codes issued automatically from a single keypress You might use a macro to automate a simple command sequence such as Turn on the DVD player and then press play Or you might compose an elaborate macro to power up an entire system select a source choose a Listening Mode and begin playback again all from a single keypress The HTR 7 can store one macro on each of its function keys these exclude the Device Selector keys NOTE Macros are independent of the currently selected device RECORDING MACROS To record a macro simultaneously press and hold for 3 seconds both the MACRO key and the HTR 7 function key to which you wish to assign the macro until the status LED turns green The macro button will also light up Press the sequence of function keys to be recorded into the macro being sure to first press the requisite Device Selector key for each function you may switch devices while recording the macro as many times as necessary allowing you to create macro containing commands from more than one Device Selector page When you have finished entering the desired command sequence press MACRO again to store the macro the Learn LED a
72. nd MACRO key illumination will turn off NOTE Each macro can store a maximum of 64 command steps If you exceed this number the macro will be stored automatically after the 64th command is added Example Record a Macro to the 0 key to Turn on the VISO FIVE Select the DVD Input and Commence Playback Onthe HTR 7 simultaneously press and hold MACRO and 0 numeric zero the Learn LED turns steady green e Press AMP press ON press 1 DVD press DVD press gt Play the Learn LED blinks as each step is added e Press MACRO again to exit the macro record mode To clear a macro perform the above steps without entering any functions 31 OPERATION USING THE HTR 7 REMOTE CONTROL EXECUTING MACROS To execute a macro press and release MACRO its key illumination lights for 5 seconds While it remains lit press an HTR 7 key to which a macro has previously been stored The corresponding macro will run as each step executes its parent Device Selector s key flashes lights briefly when execution is finished the MACRO key illumination goes out Pressing any other HTR 7 key while a macro is executing will abort the macro Remember that you must hold the HTR 7 so that its infrared emitter can activate the target components NOTE When a macro executes a 1 second delay is automatically inserted between its commands If you need more than a 1 second delay between particular commands for examp
73. ndtracks For fully cinematic effect always select 100 the default Settings of 75 50 and 25 progressively reduce dynamic range making soft sounds comparatively louder while limiting the peak loudness of loud ones The 100 setting is best for late night sessions or other times when you wish to retain maximum dialog intelligibility while minimizing overall volume levels To maintain full dynamic range set DYN Range to Off IMPORTANT NOTICE DYN Range will appear as one of the options under the Listening Mode menu only if the disc being played is of Dolby Digital format The same applies when you select the digital audio input coaxial or optical as your audio source Dynamic range adjustment will be available at the Listening Mode menu only if the detected audio is of Dolby Digital format For Dolby Digital 2 0 soundtracks set Mode at the Listening Mode menu to Dolby Digital 2Ch DD 2Ch Stereo if you toggle SURROUND MODE button for DYN Range option to appear DTS The Digital Theater System Digital Surround simply called DTS is a multi channel digital signal format that can process higher data rates than with Dolby Digital Although both Dolby Digital and DTS are 5 1 channel media formats discs bearing the DTS symbol are thought to provide better sound quality due to the lower audio compression required It also offers a broader dynamic producing magnificent sound q
74. nel and include it in the service list if not yet available at the time You can also use TUNE AID to assist you in positioning the DAB antenna for best reception of the desired channel 1 While listening to a DAB broadcast press front panel s MENU button and then TUNE lt gt to select Tune aid Press ENTER The current channel and frequency are shown in the lower line of the VFD The number of o displays at the upper line of the VFD indicates the signal strength level of the current channel 2 Toselect other channels toggle TUNE lt P gt to step through the channel list Release TUNE lt gt when you have arrived at your desired channel To improve the reception of the selected channel adjust or reposition the DAB antenna until the best reception is indicated 3 Press ENTER to tune the selected channel NOTE The number of ensembles and stations that could be scanned will vary depending on your location PRUNE LIST There maybe situations wherein certain stations become inactive The Prune List option enables the deletion of these inactive stations in the service list 1 While listening to a DAB broadcast press front panel s MENU button and then TUNE lt gt to select Prune List 2 Press ENTER Use TUNE lt gt and then press ENTER to select between Cancel or OK SELECT Any inactive stations normally stations preceded by a mark are automatic
75. nfigurable punch through Key illumination with programmable timeout Upgradable Contains pre programmed library of NAD remote codes The NAD HTR 7 is ready to operate the VISO FIVE right out of the box but it is really eight remotes in one Each of the 8 Device Selector keys at the top of the handset can call up a new page of remote control codes to be transmitted by the remaining 44 keys You may teach codes from any infrared remote controlled component regardless of brand to any or all of these Obviously the most logical system is that you teach the codes from your DVD player to the DVD Device Selector page your television s codes to the TV page and so on but there is no required scheme You may load any commands to any key on any page see Learning Codes From Other Remotes below The HTR 7 is already preprogrammed with a full complement of commands for the VISO FIVE on its AMP Device Selector page and as well as with library commands to operate most NAD brand DVD or CD components on the corresponding Device Selector pages These default commands are permanent Even if you teach the HTR 7 new commands to take their place the underlying library commands remain in place and can easily be recalled should you add an NAD component to your system later see Delete Mode below NOTE For use with the VISO FIVE it should not be necessary to re program any keys on the HTR 7 AMP page
76. ng with setup DISPLAY THE VISO FIVE SETUP MENU Sotup Menu Audio Setup Menu Video Setup Menu OSD Language Exit At any source mode press the HTR 7 s SETUP button for the Setup Menu OSD to appear With the use of the HTR 7 s navigation buttons you may select various menus If the Setup Menu does not appear check your applicable video connections NOTE The Setup Menu will not appear if a headphone is plugged in at the front panel s PHONES jack Unplug the headphone for the Setup Menu to appear when HTR 7 s SETUP button is pressed NAVIGATING THE SETUP MENU OSD AND MAKING CHANGES To navigate through the Setup Menu OSD options please do the following using the HTR 7 remote control 1 Press amp keys to move up or down the menu selections 2 Press ENTER to select a menu 3 Use lt gt or ENTER keys to select through the options of a particular menu 4 To save a menu item that you have set up use W key to scroll down and select the particular menu s Save amp Exit option Press ENTER to save the settings and at the same time exit the menu Select Do not Save amp Exit if you choose not to implement the settings you have set up To exit the Setup menu or from a menu option without saving press HTR 7 s SETUP key 12 Downloaded From Disc Player com NAD Manuals DISPLAY DISC OSD You can display the general disc playback status on the TV screen Some items ca
77. nitor you are using If the selected resolution is not supported this setting is automatically switched to the most appropriate resolution e Picture quality may decrease when an HDMI cable longer than 5m is used IMPORTANT NOTE ABOUT HDMI CONNECTION AND SETTING With HDMI OUT connected to a HDMI compatible component component video out composite and S video output will only be available when HDMI Res is set to 480P 576P or Off For component video out composite and S video to come up unplug HDMI cable or undertake the following 1 At DVD mode and with no disc loaded NO DISC press and hold DISPLAY button The lower line of the VFD will show the current HDMI resolution setting 2 Use the remote s lt gt keys or toggle MEMORY button to select through 480P 576P 720P 10801 AUTO or OFF Select either 480P 576P or OFF to enable component video out composite and S Video output To set preferred resolution setting stop at your desired resolution setting and release lt P keys or MEMORY button BRIGHTNESS Adjust overall brightness of the image Set the brightness level over a range 7 Select BASIC to maintain default brightness setting SHARPNESS Picture sharpness could be easily lost during the recording playback process Adjust sharpness to improve the fine details of the picture Set the sharpness level over a range 7 Select BASIC to maintain default sharpness settin
78. o menus in conjunction with the Navigation button and ENTER buttons At FM XM DAB mode the MENU button also functions the same way as that of TUNER MODE button 12 TONE Press to toggle through Bass Treble Tone Defeat and Tone Active options Use the VOLUME knob to adjust the Bass and Treble levels While at either Bass or Treble mode rotate VOLUME knob clockwise or counterclockwise to adjust the Bass or Treble level within the range 12cB 13 VOLUME Turn clockwise to increase the master volume setting counter clockwise to lower it The VOLUME knob is also used to increment decrement the Bass and Treble levels 14 INPUT SELECTOR Use to select an audio video input source along with its assigned analog or digital inputs Rotate clockwise or counter clockwise to select Internal DVD gt Cable Sat gt VCR iPod gt Front gt AM FM XM DAB gt Ext 5 1 gt then back to Internal DVD 15 SURROUND MODE Toggle to select through the SURROUND MODE options See also the section LISTENING MODE under OPERATION USING THE VISO FIVE AUDIO SETUP MENU discussions NOTES Depending on the format of the currently selected input digital or analog different surround modes will be available For best results when recording to a VCR select Mode Stereo and Sub Off in the applicable Setup Menu OSD Downloaded From Disc Player com NAD Manuals IDENTIFICATION OF CONTROLS FRONT PANEL 16 STOP
79. ollowing audio video source inputs Cable Sat VCR iPod and Front Front Input on the front panel Another source input is the Ext 5 1 which is an audio only input The input becomes active whenever it is selected Use lt gt select through DVD Cable Sat VCR iPod Ext 5 1 and then back to DVD VIDEO IN A particular video input can be assigned to any of the following source inputs Cable Sat VCR iPod Front and Ext 5 1 Ideally a video input present at the video input of a particular source input should be assigned to the same source input For example a video input present at S video input of VCR should be the assigned video input for VCR source input This is actually the default setting This can be varied though by assigning a different active video input other than the particular source s default video input setting AUDIO IN Incoming digital and audio signals present at either digital or analog audio are assignable to any of the following source inputs Cable Sat VCR and Front Use lt gt to assign coaxial optical or analog audio to any of the aforementioned sources The assigned audio input will always be recalled whenever that input is selected using the front panel INPUT SELECTOR knob or the HTR 7 remote s input select buttons It is not necessary to connect at the same time both analog audio and digital audio input for every video input you employ It is preferable to make only dig
80. ons THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED DANGEROUS VOLTAGE WITHIN THE PRODUCT S ENCLOSURE THAT MAYBE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USERTO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE SERVICING INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The equipment draws its nominal non operational power from the AC outlet with its POWER switch in the STANDBY position The socket outlet shall be installed near the apparatus and shall be easily accessible CAUTION Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user s authority to operate this equipment CAUTION REGARDING PLACEMENT To maintain proper ventilation be sure to leave a space around the unit from the largest outer dimensions including projections that is equal to or greater than shown below Left and Right Panels 10 cm Rear Panel 10 cm Top Panel 50 cm IMPORTANT SAFETY INSTRUCTIONS IMPOR
81. otentially noisy stations to be received Noise is reduced if the FM station signal level is less than the FM Stereo threshold since mono FM is inherently less noise prone though at the sacrifice of the stereo effect NOTE In FM XM DAB mode MENU button functions the same way as the TUNER MODE button ABOUT USER NAMES You can assign an eight character User Name to each radio preset which will show in the front panel readout whenever that preset is recalled ENTERING USER NAMES To name a radio preset NEWS follow the procedure as below The buttons mentioned apply to the front panel s buttons 1 Recall the desired radio preset 2 Press and hold the DISPLAY button and then within five 5 seconds use the PRESET 4 1 buttons to select the first character of the name N from the alphabetical list 3 Press TUNE gt gt button to select the character and correspondingly move forward to the next position Press TUNE lt lt to go back to the previous character Repeat this process for each character in sequence 4 Press the MEMORY key to store the User Name and exit the text entry mode ABOUT RDS The Radio Data System RDS permits compatible tuners to display text determined by the broadcaster The VISO FIVE supports two RDS modes station name PS mode and radio text RT mode However not every FM station incorporates RDS in its broadcast signal In most areas you will find from one to several RDS
82. ovie mode offering sound that is more similar to Dolby Digital decoding Two channel recordings whether stereo or surround encoded are reproduced with Dolby Pro Logic Il surround processing yielding output to Front Center and Surround channels assuming these are present in the Speaker Settings menu PLII Movie is optimized for film soundtracks PLII Emulation for decoding original Dolby Surround sound film and music recordings PLII Music for music recordings DIMENSION 3 to 3 Adjusts front rear emphasis of the surround effect independently from the relative channel levels CENTER WIDTH 0 to 7 Modifies the hard centeredness of the center image by gradually mixing mono center content to the Front left right speakers as well A setting of 0 retains the center channel only default while a setting of 7 yields a fully phantom center channel PANORAMA On Off Adds a wrap around effect by extending some stereo content into the surround channels 14 Downloaded From Disc Player com NAD Manuals EARS Two channel recordings whether stereo or surround encoded are reproduced with proprietary NAD surround processing with signals output to the front center and discrete surround channels plus subwoofer assuming these are present in the Speaker Settings menu EARS extracts the natural ambience present in nearly all well produced stereo recordings It does not synthesize any ambience or other sonic elements an
83. panel INPUT SELECTOR knob If your source has a single audio out jack only or is marked mono output plug this into the VISO FIVE s FRONT INPUT R MONO input On the other hand if your source has two output jacks indicative of stereo output insert both jacks into the VISO FIVE s corresponding FRONT INPUT L and R MONO input to achieve stereo output as well 2 PHONES Accepts stereo headphone using a standard 1 4 inchstereo phone plug use a suitable adaptor for headphones equipped with a smaller plug Plugging in headphones automatically mutes output from all channels speakers but not from the AUDIO OUT jacks of the VCR and SCART OUT Europe version only See also the item on DOLBY HEADPHONE under the LISTENING MODE section of AUDIO SETUP MENU discussion NAD VISO FIVE IDENTIFICATION OF CONTROLS European Version only European Version only SWITCHED AC OUTLET a i SS 100WATTS 0 5A MAX 7 8 9 10 11 12 13 14 15 16 17 18 North American Version only __ A CHAN LINPUT _YCAB SAT VCR XM y S CE ER SUR OUND FF NT IN IN OUT 4 M SiW RES RS232 North american d oCEJO EA version only O 0000 surrouno z CENTER AN id ON y G SY WEY F OK A SWITCHED AC OUTLET e 120V 60Hz e
84. plied wire dipole FM antenna will connect to the FM connector using the supplied balun adapter It will usually work best when mounted on a vertical surface such as a wall with arms fully outstretched forming a horizontal T perpendicular to the origin point of the signal Connect the supplied AM loop antenna to these terminals If an external AM antenna is used make connections to the AM and GND terminals in accordance with the instructions supplied with the antenna See also section about LISTENING TO AM FM RADIO 17 IEC AC MAINS POWER INPUT The VISO FIVE comes supplied with a separate AC Mains cable Before connecting the cable to a live wall socket ensure that it is firmly connected to the VISO FIVE s AC Mains input socket first Always disconnect the AC Mains cable plug from the live wall socket first before disconnecting the cable from the VISO FIVE s Mains input socket 18 SWITCHED AC OUTLET This convenience outlet can supply switched power to another component or accessory It is powered ON and OFF by the front panel POWER SWITCH or by the HTR 7 s ON and OFF keys 11 SETUP SETTING UP THE VISO FIVE ABOUT THE ON SCREEN DISPLAY OSD The VISO FIVE employs a self explanatory on screen display menu that will appear on the connected video monitor TV These are required during the setup process and are useful in day to day operation so be sure to connect the monitor TV before proceedi
85. receptacles as this can result in a risk of fire or electric shock 18 Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product WARNING THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND OBJECTS FILLED WITH LIQUIDS SUCH AS VASES SHOULD NOT BE PLACED ON THE APPARATUS AS WITH ANY ELECTRONIC PRODUCTS USE CARE NOT TO SPILL LIQUIDS INTO ANY PART OF THE SYSTEM LIQUIDS CAN CAUSE A FAILURE AND OR A FIRE HAZARD IMPORTANT SAFETY INSTRUCTIONS 19 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e Ifthe product has been dropped or damaged in any way f when the product exhibits a distinct change in performance this indicates a need for se
86. rent song Song title Artist Name Album title If there is no information available the display will show ARTIST Unknown Artist or ALBUM Unknown Album as applicable The equivalent front panel key for DISP is DISPLAY MENU Press MENU to return to a previous option or menu selection Downloaded From Disc Player com NAD Manuals OPERATION USING THE VISO FIVE AM FM DB iPod 4 NAVIGATION BUTTONS While at menu options or selection lists toggle A to go up or down he options lists or song titles Press and hold A to quickly scroll hrough the song titles The equivalent front panel key for A is PRESET Kd gt I ENTER Press ENTER to select an option or start playback when applicable TUNE a lt 4 gt gt gt gt I During playback or PAUSE mode press and hold TUNE Kl lt P gt gt gt I or fast forward or backward scanning of current song Press TUNE gt gt gt I to skip forward to the next song or TUNE Hl lt 4 o skip back to the previous song The equivalent front panel key for TUNE Kd lt gt gt PPI is SCAN 4d PP PAUSE II PLAY gt Press PAUSE II during playback to stop playback temporarily Resume play by pressing PAUSE II again or PLAY gt NOTE For other navigation functions please refer to your iPod player s owner s manual Depending on the iPod player model some other functions maybe controlled using the applicable VISO FIVE
87. ress MENU and you will be directed to the Playlists option of the Menu mode Use the HTR 7 s A F or front panel s PRESET k lt gt gt I buttons to select through other Menu mode options like Artists Albums Songs Podcasts Genres Composers and Audiobook Using the corresponding front panel or HTR 7 buttons navigate and select through these VFD Menu mode options as you would when operating your iPod player independently NOTE At Menu mode your docked iPod player s click wheel and controls will not be operational Your iPod player will show in its display the NAD logo Use the corresponding front panel or HTR 7 buttons to navigate through the Menu mode options SIMPLE MODE At Simple mode refer to your docked iPod player s own display screen to navigate and make full use of its features Use your docked iPod s own click wheel and controls or the corresponding front panel or HTR 7 buttons to select through the available options as displayed in your iPod player s display screen CONTROL FEATURES Use the following control buttons in navigating through the iPod menu options These are applicable using either the front panel or HTR 7 buttons Since the HTR 7 will be the primary controller in most cases we will focus on remote controlled operations DISP During playback toggle DISP key of HTR 7 to show in the VFD lower line the following Elapsed time and remaining playback time of the cur
88. rvice 20 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 21 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition 22 Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer 23 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT CAUTION This DVD Receiver employs a Laser System To ensure proper use of this product please read this owner s manual carefully and retain for future reference Should the unit require maintenance contact an authorized service location Use of controls adjustments or the performance of procedures other than those specified may result in exposure to laser radiation To prevent direct exposure to laser beam do not try to open the enclosure Visible laser radiation when the enclosure is opene
89. s of the screen Pan Scan 4 3 Automatically displays the wide picture on the entire screen and cuts off the portions that do not fit Widescreen 16 9 Select when a 16 9 wide TV is connected Set the widescreen TV to FULL mode if necessary NOTE If you have a 16 9 display device and you have defaulted Format to Widescreen 16 9 it does not mean you will always see movies in this format Widescreen 16 9 display format must be supported by the disc being played in order to view the movie in widescreen format SIGNAL MODE Depending on the type of TV Monitor set you own select the signal mode you wish to watch your disc Refer to your TV Monitor s owner s manual to check its signal or system mode capabilities Auto Automatically detects the signal mode of your TV Monitor NTSC Select when the signal mode of your TV Monitor is NTSC system PAL Select when the signal mode of your TV Monitor is PAL system 18 Downloaded From Disc Player com NAD Manuals HDMI RES RESOLUTION HDMI video resolution can be adjusted with the VISO FIVE connected to an HDMI compatible component via HDMI OUT 480P 576P 720P 10801 Set applicable resolution depending on your TV Monitor capability Auto The best resolution is automatically selected based on your TV monitor s capability Off Select to turn off HDMI output NOTES Forsettings other than Auto be sure that the selected resolution is supported by the HDMI compatible mo
90. semble contains a number of stations transmitted at a set frequency When Ensemble is selected as the mode of station order the radio stations are arranged in the order of their ensemble names NOTE Ensemble is also interchangeably termed as multiplex by other broadcast providers FAVOURITE The VISO FIVE memorizes the top ten stations you listen as you tune in stations They will be listed at the top of the channel list DYNAMIC RANGE The level of compression of stations can be set to eliminate the differences in dynamic range or sound level between radio stations Popular music would normally be more compressed than classical music resulting in possible different audio levels when changing from one station to the other Setting the Dynamic Range to D Range 0 means no compression D Range 1 2 indicates medium compression and D Range 1 shows maximum compression No compression is recommended especially for classical music 1 While listening to a DAB broadcast press front panel s MENU button and then TUNE lt P gt to select Dynamic range Press ENTER 2 Toggle TUNE lt gt to select through D Range 0 D Range and D Range 1 The upper line display shows the current dynamic range setting while the lower line display will show the choices for the dynamic range values 3 Press ENTER to select desired Dynamic Range level TUNE AID This option allows you to directly tune to a desired chan
91. sfer The signals present at these jacks will be heard by rotating the INPUT SELECTOR knob to select Ext 5 1 as your source input There is no bass management or other processing other than master volume control available to this 5 1 Channel Input While the multi channel audio outputs of a DVD Video player can be connected to these jacks using the VISO FIVE s own Dolby Digital and DTS decoding and digital analog converters via a digital connection will usually produce superior results 12 HDMI OUT Connect the HDMI OUT to a HDTV or projector with HDMI input WARNING Before connecting and disconnecting the HDMI cable both the VISO FIVE and the ancillary source must be powered OFF and unplugged from the AC outlet Failure to observe this practice may cause permanent damage to the equipment connected via the HDMI socket IMPORTANT NOTICE When playing DTS or Dolby Digital material ensure that the volume of your HDMI equipped TV is muted There may be a rushing noise heard if your TV is not capable of decoding the DTS or Dolby Digital Bitstream most TVs do not have this capability 13 MP DOCK The VISO FIVE is equipped with a data port in the rear panel where an optional NAD IPD 1 Dock with iPod NAD IPD 1 can be plugged in Connect the MP DOCK DATA PORT jack of the VISO FIVE to the corresponding DATA PORT socket of the optional NAD IPD 1 14 XM MODULE INPUT North America version only Connect XM radio cab
92. t applicable for Subwoofer CHANNEL LEVELS Front Center Front R Surr L Surr R Subwoofer Do not Save amp Exit Save amp Exit Adjusting the relative balance of your system s loudspeakers ensures that surround sound recordings whether music or film will present the balance of effects music and dialog that the artists intended Additionally if your system incorporates a subwoofer it establishes a correct relationship between the volume of the subwoofer and the other speakers and thus of low frequencies bass to other sonic elements USING AN SPL METER It is quite practical to perform the VISO FIVE level setup routines by ear and careful work will produce acceptably accurate results However the use of an inexpensive sound pressure level SPL meter such as Radio Shack part number 33 2050 makes this task easier more accurate and more repeatable Ownership of such a meter could prove a valuable audio tool Your NAD audio specialist may be able to help you with temporary use of a meter The SPL meter should be placed at the primary listening position at approximately the height of the seated listener s head A tripod is helpful but with a little duct tape almost anything a pole lamp music stand or ladder backed chair for example can do as well Just be sure that no large acoustically reflective surfaces obstruct or are near the microphone element Orient the meter with its microphone usually at one en
93. te recall 1 To store a radio preset first tune the desired frequency see above then press the front panel MEMORY button The VFD will show a blinking MEMORY icon and the next available vacant Preset number 2 Press MEMORY button again to store the desired frequency on the Preset number shown or use the kiq gt gt I keys to select another available Preset number 3 Then press MEMORY key button again Your desired frequency is now stored in the assigned presets The Radio Presets must be stored from the front panel This setup function is not accessible from the HTR 7 remote control Use the 44 1 keys on the front panel to step up or down between presets Press and hold k lt gt gt I to scroll continuously up or down The HTR 7 remote s PRESET keys work similarly Empty presets will be skipped during preset tuning DIRECT RECALL OF A PRESET You can directly recall a desired Preset number 1 Toggle ENTER button to switch between Preset and Tune mode see the lower line of the VFD Select Preset mode 2 Using the numeric keys of the remote control directly key in your desired Preset number For example to enter Preset 5 press 5 NOTE Ensure that the DEVICE SELECTOR setting of your HTR 7 is set to TUNER AUTOMATIC PRESET Preset stations may also be programmed automatically for the entire FM or AM band 1 Toggle the AM FM DB button to select FM or AM
94. tents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited 35 www NADelectronics com 2009 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved No part of this publication may be reproduced stored or transmitted in any form without the written permission of NAD Electronics International VISO FIVE Owner s Manual Issue 2 13 05 09 Downloaded From Disc Player com NAD Manuals
95. th your own iPod player you can enjoy listening to your favorite tracks and playlists as well as view applicable still image and video playback You can control your iPod player using the assigned buttons in the VISO FIVE front panel And with the corresponding HTR 7 remote control function keys you can select the materials stored in your iPod for playback as well as access many of its functions even from across the room The optional NAD IPD 1 also charges your iPod player while it is connected to the VISO FIVE NOTES NADIPD 1 and iPod player are optional and not supplied with your VISO FIVE iPod player functions features and playback capabilities accessible through VISO FIVE may vary depending on your iPod player model When using the HTR 7 to control the iPod functions make sure that the Device Selector is set to MP DOCK CONNECTING THE OPTIONAL NAD IPD 1 DOCK WITH iPod AND iPod PLAYER TO THE VISO FIVE Make sure that all the devices are unplugged before making the connections 1 Connect the NAD IPD 1 s plug into the VISO FIVE s MP DOCK data port 2 Connect also the NAD IPD 1 s S video and audio out to the VISO FIVE VCR input the default iPod source allocation in the VISO FIVE 3 Dock your iPod player into the NAD IPD 1 4 After linking together your iPod player NAD IPD 1 and the VISO FIVE you can now plug them IN to their applicable power sources 5 With your iPod player NAD IPD 1 and VISO FIVE all
96. tors are employed throughout to ensure maximum signal integrity E A R S AND DIGITAL SURROUND A key element of the VISO FIVE s unique musical aptitude is NAD s proprietary Enhanced Ambience Recovery System EARS In sharp contrast to many ambience synthesis music surround modes EARS exploits the VISO FIVE s substantial DSP power to route the ambient content that is encrypted in virtually all natural acoustic recordings to the appropriate main center and surround speakers without resorting to artificially generated reflections or regeneration EARS natural ambience yields a subtle but exceptionally effective surround mode that naturally enhances the spatial presentation in a fashion suitable for serious music listening Dolby Pro Logic II Music and DTS Neo 6 Music modes can also create enjoyable experience from 2 channel sources On the digital side the VISO FIVE combines extraordinarily high speed DSP processing employing one of the most advanced high speed DSP engines available A single high precision master clock synchronizes all digital circuits to eliminate the timing errors jitter that otherwise compromise sonics The result is legitimately state of the art surround decoding from Dolby Digital and DTS sources and 5 1 channel reproduction with genuinely superior sound quality in all modes EASE OF USE Despite the effort NAD has invested in the VISO FIVE s sonic performance we expended no less in making
97. u select unlock parental lock is not active and the disc plays in full NOTE Should you forget your password reset your password by restoring the VISO FIVE to its factory default settings Refer to the Factory Default Settings section under the heading SETUP SETTING UP THE VISO FIVE 20 Downloaded From Disc Player com NAD Manuals DIVX SETUP DivX Subtitie DivX Registration OK Do not Save amp Exit Save amp Exit Unicode DIVX SUBTITLE Depending on the DivX media only those Divx Subtitles recorded on the DivX media are available The following are the available DivX subtitle language format and their corresponding language coverage Western European Albanian Breton Catalan Danish Dutch English Faroese Finnish French Gaelic German Icelandic Irish Italian Norwegian Portuguese Spanish and Swedish Turkish Albanian Danish Dutch English Finnish French Gaelic German Italian Kurdish Latin Norwegian Portuguese Spanish Swedish and Turkish Central European Albanian Croat Czech Dutch English German Hungarian Irish Polish Romanian Slovak Slovene and Serbian Cyrillic Bulgarian Belorussian English Macedonian Moldavian Russian Serbian and Ukrainian Greek English and modern Greek Hebrew English and modern Hebrew Arabic Arabic Baltic Baltic Vietnam Vietnamese Unicode Default subtitle DIVX REGISTRATION The Registration code details necessary for VOD Video On Demand
98. uality Downmix 2Ch A Dolby Digital or DTS digital signal format can be automatically downmixed to produce two channel stereo audio DOLBY HEADPHONE Dolby Headphone technology compatible with any pair of conventional headphones accurately simulates the experience of hearing a 5 1 channel speaker system properly set up in a listening room minus the annoying listener fatigue effect that plagues other headphone based virtual surround sound offerings Dolby Headphone technology is ideal for private playback of multi channel entertainment without disturbing others nearby Dolby Headphone models the sound of a playback system into three different istening environments based on acoustic measurements of real rooms DOLBY HP MODE 1 is a small well damped room appropriate for both movies and music only recordings This decoding process is known as the Dolby Headphone Reference Room DOLBY HP MODE 2 is a more acoustically live room suited to music istening but also great for movies DOLBY HP MODE 3 is a larger room more like a concert hall or movie heatre Select DOLBY HP OFF for normal headphone audio listening Downloaded From Disc Player com NAD Manuals OPERATION USING THE VISO FIVE AUDIO SETUP MENU INPUT SETTINGS Input Cable sat Video In Audio In Do not Save amp Exit Save amp Exit Cable Sat Coaxial INPUT Aside from the VISO FIVE s internal DVD the VISO FIVE is also equipped with the f
99. ucts NAD s Music First design philosophy guided the VISO FIVE s design such that it can confidently promise you both state of the art surround home theater and audiophile quality music listening for years to come Downloaded From Disc Player com NAD Manuals INTRODUCTION TABLE OF CONTENTS LOOM roeas o EE ote sia ee Dans cate ebay ete a TOEA 22 PROGRAMMING murua ema enasna eia E EE A ERA 22 PLAYING MP3 AN MAVJ PE G onies E EE E EA 23 TMMER SETUR A araona anA lre OE AE 23 AUTOMATIC POWER OFF FUNCTION 00 nro anui 23 USING THE VISO FIVE AM FM DB iPod 0eseeeeeeeee 24 LISTENING TOAM EM RADIO sis cea einna aak 24 ABOUTANTENNAS oinp oE EEE EREE 24 ASSEMBLING THE LOOP ANTENNA 000 e eee eee eee 24 SELECTING THE RADIO a 2c cles che Tr E a aed Stew athe 24 SETMING RADIO PRES Eiaeai E EE AE EE EIE 24 CHOOSING TUNER MODE orase iinr En EROE 25 ABOUTUSER NAMES vesinsins ayers waren irio EA 25 ABOU TRD S ai se nons aapea AEAEE E E AEE 25 VIEWING RDS TEX sicdisssesestie cts dentate te Som shale ERON OEE R 25 PBOW TIA DON te cea EE E ETO E O E ENTA 25 CONNECTING THE DAB MODUL E iss0sisn eos cnsdnt ronron eos 25 DABS ORERATION reinar eanne a a nsastet 26 SERVICE EIST spretna ana tienne oai aaa A E EARE 26 DAB TUNER MODE pianisten n EE EA E OO NR 26 FOCAL SCAN straini T T 26 PRESET TUNE in o E E OE E OORS OA 26 STAMION ORDER aree
100. ve unique menu structures called DVD menus For example DVDs programmed with complex contents provide guide menus and those recorded with various languages provide menus for audio and subtitle language Press MENU during play the DVD menu available on the disc is now displayed Pressing MENU again resumes play from the scene when MENU was first pressed RANDOM Press the HTR 7 s RANDOM key during playback and Random briefly appears on the upper line of the VFD Ran will then be displayed in VFD alongside the track number and playback time Press kt gt gt I for random playback of audio tracks Press RANDOM again to return to normal playback For iPod songs Ran Song or Ran Album will be displayed in the VFD as applicable Ran Song allows random playback of songs within an album or playlist On the other hand Ran Album randomly plays all the songs in an album Afterwards another album is randomly selected and also randomly plays all the songs in this album 21 OPERATION USING VISO FIVE FEATURES REPEAT CUSTOM VCR PROGRAM CLEAR REPEAT DVD CAB SAT VCR MP To repeat the playback of a particular track file or chapter press the VISO FIVE s REPEAT key once Pressing the same REPEAT key a second ime will repeat all the tracks files or title Turn off repeat mode by pressing REPEAT button a third time Depending on your desired repeat mode the following are shown
101. wer button again or HTR 7 s OFF button turns the unit back to standby mode Note that when you do choose to switch OFF to standby using the front panel Power button the VISO FIVE s memory back up system will store channel level tuner preset and other settings for several weeks while the unit is switched off Pressing the OPEN CLOSE button on the front panel or the HTR 7 remote s 4 button will switch ON the VISO FIVE from standby mode and at the same time open the disc tray NOTE It takes around 10 seconds for VISO FIVE to switch to full standby mode when it is powered OFF from source inputs other than DVD mode In this condition it also takes around 10 seconds for the standby LED to switch from blue to amber color STANDBY LED This indicator will light up amber when the VISO FIVE is in standby state When the VISO FIVE is at ON state this indicator will illuminate blue NAVIGATION AND ENTER BUTTONS The navigation buttons PRESET k lt PI TUNE lt lt gt gt in conjunction with the ENTER button allows one to navigate the OSD title and menu options In AM FM XM mode use PRESET Kt 1 to step up or down between radio presets Unused presets are skipped over Note that Presets must have been previously stored Refer also to the item on SETTING RADIO PRESET under OPERATION USING THE VISO FIVE AM FM DB iPod discussions Pressing momentarily the TUNE lt lt gt gt button will manua
102. will provide a clear line of sight within 23 feet 7 meters between the VISO FIVE s front panel and your primary listening viewing position this will ensure reliable infrared remote control communications The VISO FIVE generates a modest amount of heat but nothing that should trouble adjacent components It is especially important that sufficient ventilation be provided If you are contemplating on locating the VISO FIVE within a cabinet or other furniture consult your NAD audio video specialist for advice on providing adequate airflow Downloaded From Disc Player com NAD Manuals INTRODUCTION GETTING STARTED QUICK START In case you simply cannot wait to experience the performance of your new NAD VISO FIVE we provide the following Quick Start instructions to get you underway Before the steps below connect your VISO FIVE to a TV monitor Please make all the connections to your VISO FIVE with the unit unplugged It is also advisable to power down or unplug all associated components while making or breaking any signal or AC power connections PLAY A CD OR DVD MOVIE Connect the VISO FIVE s composite Video or S Video MONITOR OUT jack to your TV monitor s corresponding input e Connect your speakers to the VISO FIVE s FRONT R FRONT L SURROUND R SURROUND L and CENTER terminals Make sure to connect red o red and black to black with care to avoid stray wires or strands crossing between term
103. wn a film s dialog level by rising lowering the center channel or reducing excessive deep bass or enhance deep bass by lowering rising the subwoofer level Use the HTR 7 s SURR CENT and SUB keys for direct access level adjustment of these channels over a range of 12cB The SURR button will adjust first Surround Left SL channel level To adjust Surround Right channel level press and release SURR button the VFD will show SL and the current Surround Left channel level Wait for the display to SR and the current surround right channel level You can now to set your preferred Surround Right channel level by pressing SURR key NOTE The lower line of the VFD will display the channel being adjusted and the corresponding level setting ADJUSTING THE TONE CONTROLS The VISO FIVE bass and treble controls are adjusted using the front panel s TONE button in conjunction with the VOLUME knob The corresponding TONE and VOL amp keys of HTR 7 can also perform the same functions Referring to the lower line of the VFD toggle TONE button to select Bass Treble Tone Active or Tone Defeat While at either Bass or Treble mode rotate VOLUME knob clockwise or counterclockwise to adjust the Bass or Treble level within the range 12dB Bass and treble settings affect only the front left right channels and are active in all SURROUND MODES Select Tone Defeat to bypass the Tone Controls

NAD VISO FIVE Operating Instructions Manual

Contents

Download Pdf Manuals

Related Search

Related Contents