PiSector 3G/4G Cellular & Landline All in one Wireless Security
Contents
1. 3 seconds when motion is detected The Motion Sensor will then short blink once as it recycles itself for the next motion event 1 Move away from the area that is in direct line of sight of the Motion Sensor move to an adjacent room Wait 2 3 minutes until the LED stops blinking 2 Move back into the line of sight of the Motion Sensor walk around 3 5 steps This will trigger the main console If the Motion Sensor test is successful the LCD screen will display xxx Sensor Alarm if system is armed If these words do not appear either A the 20 second waiting period since the last trigger has not expired or B the Motion Sensor is not in communication with the PISECTOR system main console If you want to re start the initialization again open the Front Cover and remove battery Wait 5 seconds before re installing the battery Re attach the Front Cover Note1 To save battery power motion sensor may be insensitive if you activate it more than three times in a few minutes Please leave the detectable area for several minutes and come back It will detect you again Note2 Motion sensors may be insensitive or give false alarms if the temperature is more than 98F 37C Mount Motion Sensor D Place the motion sensors in the following location recommendations check marked locations shown in Figure C Avoid the example location marked with the X which are household areas that Ha P typically cause false alarms such as heat W A2. WKP 03 This keypad does not work alone You need to program it with PiSector Alarm Systems It supports System model GSO7 GS08 PSO3 series systems Anti Remove Spring Package includes e PiSector Keypad x 1 Power adapter 12V 1A input 100 240V output 9 12V Current 1A e RFID Door Access Keychain Tag X 2 Step 1 Connect power to the keypad and you will see Arm indicator light flash once every second This is Stand by Disarm status meaning system is at power on To keep internal back up battery in charge please turn on the battery switch to ON position Put the keypad ona hard surfaced table and make sure to not trigger the keypad by releasing the anti move spring or by pressing the anti move spring with hand Make sure the keypad does not get triggered during programming Step 2 At your main console press Program followed by password Then choose Remote Controllers press Enter select Add press Enter again When you see Trigger Controller Code display go to your extra keypad press default password 1 2 3 45 6 followed by Arm key the lock icon and you will see 9 digits display on the console This is unique address for the extra keypad on the console It will be auto saved after 3 seconds and you will see Add Owner Name You can give a name to this keypad on the console and then follow the steps to record a voice for the keypad name as your choice optional After that press Enter to continue until you see Add
3. MAKE SURE ONLY ONE SENSOR IS TRIGGERED EACH TIME TO AVOID ANY ACCIDENTAL TRIGGERING OF A DIFFERENT SENSOR PLEASE KEEP ALL YOUR MOTION SENSORS IN DIFFERENT ROOMS AND MAKE SURE ALL WINDOW DOOR SENSORS ARE ATTACHED TO THEIR MAGNET PARTS IN CLOSED STATUS Edit Zone Name Highlight Edit Zone name press Enter and you will be able to rename the sensor Record Zone Name Highlight it press Enter select Record you are able to record 5 seconds of your own voice If recording a sensor s name in your own voice this is what you will hear to identify that sensor when you receive an alarm call Emergency Zone Highlight it press Enter Default is NO f you set YES the zone will be on 24 hours regardless of your system s Arm or Disarm status This is recommended to be used for smoke detector panic button water leak sensor and temperature sensors only DO NOT set any door sensor or motion sensor as Emergency Zone Home Zone Highlight it press Enter Default is YES if you select NO the zone will disable during home alarm status recommended setting for motion sensor NO all Window door sensors YES Chime Zone Highlight it press Enter Default is NO if you set as YES the zone will alert you with a bell sound during disarm and home alarm status use for doors only Delayed Zone Highlight it press Enter Default is NO if set YES allows you to come back home and open the door without immediately triggering the system System default delay
4. alarm time is 45 seconds You can change this time by going to System Settings to set the Alarm Delay time Siren Enable Highlight it press Enter Default is YES if set NO siren will disable when this zone triggered no siren alarm will sound Note All zones are instant zones by Default Instant refers to the system being immediately armed if any zone is triggered when the system is in armed status Delete select it then press Enter you can find the target sensor and delete it you can delete any sensor from the console panel NOTE After programing all sensors to your console please test each sensor before you mount the sensor to the appropriate location DO NOT close the door faster than one second during testing open door and wait 1 2 seconds when you see sensor light off then close the door otherwise the console may only receive door open signal and not detect the door close signal and will not reset properly for the next open cycle Place each sensor in the appropriate location Note If possible place the bracket on the stationary frame of door or window and place the magnet on the door or window itself For better adhesion you can clean window door surfaces with rubbing alcohol before mounting hardware You may also apply super glue on the surface of window door before you apply 3M mounting Double Hung Window e Various orientations between the Bracket and Magnet
5. may i be used as long as 3 4 distance is not exceeded See denies Example in Figures 1 4 a eet YW L a OD Figure Figure 2 Figure 3 Figure 4 Level Orientation Angled Orientation Perpendicular Orientation Perpendicular Orientation NOTE SPACERS IN BOTTOM TRAY MAY BE USED ON THE BRACKET OR MAGNET TO ADJUST ALIGNMENT Once you have determined the appropriate location and orientation for the Bracket and Magnet attach them with double sided tape the Magnet Space and Bracket Space are optional only apply when your door window gap is too big or too low foal y AIN Jo fi SS Cee AN IS J O QL te A g Magnet Space Bracket Space Bracket C7 i optional use Sensor R Arakel Tape Magnet Tape Optional use op Program and Mount Motion Sensors Separate the front and back covers of the Motion Sensor by pressing the tab with your 1 2 finger or the tip of a pen Figure A and B Remove insulating paper from the battery and CLOSE the cover The sensor needs 1 3 minutes to initialize itself You will see a red indicator blink once every 3 seconds during initialization If you don t see the indicator blink as described during initialization please V open the cover remove the battery and reinstall the battery again until you see the indicator flash as described The sensor will be ready for use when the indicator stops an blinking Note DO NOT keep the cover open since it may effect
6. off this warning tone Default is No Encrypt select Encrypt then press Enter you will see default 1234 and a blink you can then directly input another 4 digits to encrypt your siren BEWARE If you change encryption code to a new code you will need to reprogram all of your wireless sirens to the console again You may change it before you program your sirens Once you change the code DO NOT change it again while adding additional sirens otherwise you will lose the first siren s program Video hitps www youtube com watch v JcPCwCBLQyc https www youtube com watch v BQEkK__q3Ug Add Contact Phone Numbers Press PROGRAM key on console Enter the default password 888888 Use scroll key to select Phone Numbers press Enter you will see the following menu Add Select Add press Enter You will see Inout Phone Number Directly input your area code and phone number press Save You can add a maximum of 6 numbers for emergency contact if the system is triggered It is recommended to add your cell phone and your family or friends numbers DO NOT add 911 or the local police number unless you get a permit Edit Select Edit press Enter You will see Phone 1 Phone 2 select the target number which you want to edit then press Enter you will see Auto login press Enter If you set Auto login as Yes then you can remotely call the system telephone number from anywhere in the world You do not need to enter the password again to save you t
7. press Enter you will see Put siren in Setting Mode Go to the wireless siren and press the code button one time on the wireless siren you will see all 4 lights are on This means the siren is in setting status waiting for the console to send a signal Then go back to the console press Enter and you will hear two beeps from the console and will see Add successful Then you need to press Set button 5 times until all lights are off to test the set mode on siren DO NOT test it when all 4 LED lights are on Caution If you press and hold code button more than 3 seconds the siren will be deleted from console panel Code Button Add an outdoor wireless sensor highlight Add press Enter you will see a default siren name such as Siren1 Siren2 Siren3 then press Enter you will see Put Siren in Setting Mode Plug siren into the power adapter 9V 500mah and you will hear ONE beep Unplug and plug the siren a second time within seconds after the first time you will hear ONE beep again Unplug and plug the siren for a third time within seconds after the second time you will hear a FEW short beeps from the siren The FEW short beeps mean the siren is ready and in setting mode for program Go back to the main console and press Enter immediately no more than 5 seconds after the few short beeps you will hear 3 beeps 2 short beeps and 3 beeps consecutively for confirmation That means your siren has been added to your main console You may p
8. the sensor during initialization and cause the sensor to not work properly K notification 2 switch for LED signal light The default is set to on but if you do not want a flashing light Wr when the sensor detects an intruder you can turn it off When the battery is low the LED a light becomes yellow Motion sensor sensitivity adjustment A Switch 2 gt anes B Switch 1 Low sensitivity Switch 2 at ON position and Switch 1 at OFF position ig Medium Sensitivity Switch 2 at OFF position and Switch 1 at ON position High Sensitivity Default Switch 2 at ON position and Switch 1 at ON position 1 switch for battery notification Default is set to ON OFF position disables the low battery R A gt Program the Motion Sensor only for DIY kit or add new sensors Sensitivity Adjust If you received a pre programed system kit please ignore this step and do not program 1 amp 2 Switch it again Before programing any sensor you need to switch off all your existing sensors and disarm your system Press PROGRAM button on console and enter the default password 888888 Use Scroll key to choose Sensor then press Enter on Console press Enter you will see Trigger Sensor Code then walk 2 3 steps in front of The Motion Sensor which you have prepared and you will see nine digits displayed on console screen for 1 2 seconds This is the unique address for this sensor The Console will request you add a Zone Name for thi
9. up and down to move and select menu list for functions you can also use this key to find last 30 alarm events during System Disarm Status Function keys Search when you see an icon display on LCD screen you can press Search to find existing events Back use to exit the last step during programing Enter to confirm your information Mute quiets all keyboard sounds Vol Vol for adjusting the console s sound volume Place the console near your phone cord Remove the table stand and cover on back side of console SIM Card Slot Please pay attention to the direction arrow marked on the slot LOCK OPEN DO NOT insert or take out the SIM card when the main unit console panel is powered on Option Connect the phone cord to LINE Port on back of console Remove the SIM card cover Push table stand and slide down to open Connect your home telephone to TEL port on back of console Route the phone cord through the channel toward the side of the console if you have no landline you can use OBi110 MagicJack Vonage Ooma ati A r ag E an Battery are VolP service to connect your Internet router modem A B e AAN then connect console to the VolP device C O i f a Note f you use only a landline you cannot dial out via the console you will need to use your home phone to __ j SR GR 5 dial out or to receive calls system will auto dial out if alarming but if you use a GSM SIM card the ma
10. Disrcror PiSector GSM Cellular Wireless Alarm System User Manual GS08 Read manual fully before use PiSector Inc USA www pisector com Welcome to PISECTOR Thank you for choosing PISECTOR Everyone at PISECTOR is committed to giving you the best home security available today and we want you to know that we take the safety of your home and family very seriously PISECTOR was the first to develop a personal alarm system with state of the art home protection at an affordable cost Our innovation has made us one of the fastest growing security companies in the industry PISECTOR offers you the Ademco Protocol Security System We ve put complete control of your security system in your hands anytime from anywhere in the world PISEC TOR allows you to instantly arm and disarm your system change your system settings check your home security system s status and so much more We encourage you to change the default password as soon as you get your system set up Congratulations You won t find anything like PISECTOR anywhere else in the market place Our user friendly systems are designed with more functions and at an affordable price This guide will walk you through the easy set up of your PISECTOR system Your system has already been customized and tuned so everything is ready to go when you open the box Please be sure to register with PISECTOR com for any needed tech support and to receive future product updates Aga
11. Y j air conditioning fans or direct sunlight 5 _ The recommended mounting height is 6 5 7 0 feet for both coverage and pet immunity purposes E Apply the 3M adhesive tape in the locations shown in Figure D for corner mounting or wall mounting apply super glue on the surface of window or wall before applying 3M adhesive tape to prevent sensors from falling If you prefer to use screws to mount the motion sensor follow the screw position shown in Figure E optional Pehi A A aehotoh N oe i fi T Ji it T Ahi Yle 2 y ll A A 1 i Ih gt ny q Ly U an Ki R i f Nop a a y Pa Tape For Rw w Wall Mount Comer Fix Tape For BS Corner Mount vs E 3f CE i S L C i w o O Q a R f 2 mu Detection Patterns Side View SS Replacement Battery CR123A Mounting Height 6 5 7 0 feet Range Approximately 40 feet with 90 degree vertical field of view and a 110 degree field of view in the horizontal plane Wireless Sirens Plug the siren into wall outlet then press PROGRAM key on console Enter the default password 888888 Use scroll key to select Wireless Sirens press ENTER you will see the following menu Add If you received a pre programed system kit please ignore this step and do not program it again Add an Indoor Wireless Siren highlight Add and press Enter you will see a default siren name such as Siren 1 then
12. ed system kit please ignore this step and do not program it again All new Door Window sensors you need should be programed to your console 1 Use your right thumbnail to Se are ie eee Transmitter pull bracket out a little bit 2mm ne P T Magnet a g 2 Using thumb and Ji hold both sides of the cover and pull up TSSL e Open the cover and remove the insulated paper then close the cover Place small magnet next to sensor Press PROGRAM button on console enter the default password 888888 Use Scroll key to choose Sensor then press Enter on console Add Press Enter again then you will see Trigger Sensor Code Trigger your sensor by moving the small magnet away from the large transmitter Then console will request you to add a Zone Name for this sensor Input a name for the sensor then press SAVE You will see Record Sensor Name press Enter record your own voice for this sensor This is what you will hear when you receive an alarm call Note Each time you press Add follow above steps You can add from 1 to 50 sensors Edit Select it then press Enter you can use Auto search or Manual search to find your target sensor and highlight it then press Enter to Edit Sensor Functions as listed below Note if you don t know sensor name then choose Auto Search when you trigger an individual sensor its name will be displayed on the console panel Select the sensor name and press Enter then you will see the menu display as below
13. he monitoring center station default is NO Upload Arm Disarm Data Select and press Enter if you set YES every time you arm or disarm your system the information will be uploaded to monitoring center station default is NO Daily Schedule Press PROGRAM key on console Enter the default password 888888 Use scroll key to select Daily Schedule Enable If you want to enable this function first select Disable then press Enter set NO then go back and select Enable you can set the Arm time for your departure and Disarm Time for when you arrive Home then the system will Arm Disarm automatically on schedule so that you will never forget to arm or disarm system Disable If you want to disable this function select Disable then press Enter and check Yes Default is YES disable System Settings Press PROGRAM key on console Enter the default password 888 888 Use scroll key to select System Settings you will see the following menu Password Select Password then press Enter You will see old Password 888888 Then press Enter and input 6 digits not letters or icons press Enter again and input same password to confirm your new password then press Save Arm Delay Time Select it and press Enter you will see 60 directly input 2 digits for your delay time You can change the setting to allow you enough time to leave the house Default is set for 60 seconds which is the maximum delay time for the system Alarm Delay Time Select it and pre
14. ime when entering system remotely It is recommended to set only your own number as auto login For all other numbers keep default as No Delete Select Delete then press Enter you will see all numbers which you saved choose the target number which you want to delete then press Enter and delete it SMS Numbers This system can store 3 text message receiving cell phone numbers When alarming e g power outage or triggered sensors the console will send a text message to all listed numbers Press PROGRAM key on console Enter the default password 888888 Use scroll key to select SMS Numbers press Enter you will see the following menu Add Select Add press Enter You will see Input Phone Number directly input your area code and cell phone number press Save You can add a maximum of 3 numbers to receive alarm text messages Delete Select Delete then press Enter you will see all saved numbers choose the target number which you want to delete then press Enter and delete it Arm Disarm Notification Select Arm Disarm Notification then press Enter if you check Yes you will get a text message notification each time you ARM or DISARM the system default is NO Outgoing Message Press PROGRAM key on console and enter the default password 888888 Use scroll key to select Outgoing Messages press Enter you will see the following menu Edit Text Message press Enter you can directly input an outgoing text message Record Voice Message Se
15. in e console can function as a telephone you are able to aiina aein dial out and receive calls Connect the power adapter to POWER port on back of console Route the power adapter 12V 1A cord through the channel toward the side of the console Plug the power adapter into a nearby electrical wall outlet that is not controlled by a switch Set the Battery Switch to ON position for internal battery backup charging DC 12V Positive Wired in Keychain Remote Press to Arm Activates your system as Away from home ARM DISARM Press A to Disarm Deactivates your system when you return home Press fi to Home arm Activates your system as Stay Home if you go to Sensor Edit and set part of sensors for Home zone as No when you press Home that sensor will disable and all SOS other sensors will remain enabled Press this key you will see icon X on LcD screen that means you have enabled your Chime function to make it work go to Sensor Edit and set your door sensor for Chime zone as Yes you will hear musical bell sounds when you open your door press once to enable press once again to disable Pressa once for silent emergency alarm mode This allows you to call for help silently when someone threatens your life without triggering the siren and alerting the intruder If you press Ea and hold for 3 seconds the siren will start sounding loudly in emergency alarm mode Program Remote Keychain If you received a pre programed sys
16. in thank you for being a PISECTOR customer We re doing everything we can to make sure your home and family stay safe sincerely PiSector Inc System Components Program press this key then input password you will enter program status default password 888888 LCD Screen lt I gt ES Chime Icon lt 7 Arm press this key and input password you can Low Battery activate your system as Away from home Disarm press this key and input password you can SECTOR Scroll keys deactivate your system Chime press this key you will see icon X on LcD screen that means you have enabled your Chime Function keys Sensor signal indicator Away Activate Deactivate system Bell music sounds Home Activate Microphone Call End key function to make it work go to Sensor Edit and set your door sensor for Chime zone as Yes a musical bell ro ma I tone will sound when you open the door Home press this key and input password you can activate your system as Stay Home if you go to Sensor Edit and set part of sensors for Home zone as No when you press Home those sensors will disable all other sensors will still be active Emergency press this key anytime and it will instantly trigger your alarm system 24 7 regardless whether your system is armed or disarmed TALK END enter a phone number then press this key to make a call and to hang up when finished only works with SIM card installed Scroll Key press this key to page
17. lect it and press Enter select Record and press Enter You will see Recording and a counter from 10 to 00 When you see 10 you need to immediately begin recording your voice and stop when you see 00 It is recommended that you record your home address for the outgoing message Play You can select Play to play your voice If you do not like it you can Delete it and Record it again until you are satisfied Note The closer you are to the console during recording the better the quality of the recording Your mouth should be no more than 2 inches away from the console Connect Monitoring Center Press PROGRAM key on console Enter the default password 888888 Use scroll key to select Monitoring Center You can call your Monitoring Company to set up all requests Please make sure your monitoring company supports ADEMCO protocol if you want a third party Monitoring Company to monitor your system it will cost you monthly monitoring fees depending on which company you choose Monitoring Center Number Select and press Enter Then select Add to add your monitoring center telephone number ADEMCO Contact ID Select and press Enter then select Add to add your monitoring company account number Select Delete to delete your account number Select ADEMCO Contact ID then press Enter to select the protocol ID according to your monitoring center protocol ID request Upload Alarm Data Select and press Enter if set YES all your data will be uploaded to t
18. ll key to choose Sensor then press Enter on Console Choose Edit press Enter then choose Manual Search press Enter use Scroll key to find Panic button name and highlight it then press Enter use Scroll key to choose Emergency zone then press Enter highlight Yes then press Save use function key Back to exist the program In the SAME way you can add a Smoke Detector Water Leak Sensor Carbon Monoxide and Temperature Sensors You also can add a Glass Break Sensor to your system Wireless Signal Transmitter option Wireless Signal Transmitter expands your wireless range up to 500 feet and makes the communication between all sensors and the main console better Please install the antenna and plug a 12V 1A power adapter to the Power plug Place the Wireless Signal Transmitter away from the main console for about 10 feet Keep code 4 and 5 at ON position all other codes at OFF position The Transmitter will then start to auto transfer all the signals between the sensors and the main console Note if you notice any issue such as an open icon displaying on the screen when the door or window is open because the main console has detected that the door or window is open and the same icon is still showing after physically closing the door or window a communication problem must have caused this issue For a solution you may need purchase this repeater to add to your system SECTOR Extra Wireless Keypad Instruction option Model
19. move the keypad from the wall At backside of the keypad you will see Reset button press the reset button and hold for 3 seconds it will reset the keypad password to default password 123456 Wired Port Connection for Magnetic force lock or Electronics lock Option Magnetic force lock and Electronic lock Please make sure which type of lock you have and select the correct connection Fig 1 for Normal Close Fig 2 for Normal Open NC COM GND GND Lock Power keyboard Power Supply if you choice this two port to supply keyboard then you do no need connect power adapter anymore keyboard Power Supply if you choice this two port to supply keyboard then you do no need connect power adapter anymore
20. ns and remotes to the console again Beware of this function About System Version press Enter you will find your software version Production Date press Enter you will see the producing time of your system Manufacture By Pisector Inc IMEI press Enter you can find IMEI number for your system maybe request to active your SIM card Remotely Control Your Home Security Alarm System Dial the number of the main unit console panel by your cell phone and after 1 ring you will hear a voice prompt Please enter password If the password is correct you will then hear a voice prompt Please enter instruction then you can press 1 to arm Press 2 to disarm Press 3 to monitor or Press 4 to intercom If the password is incorrect you will hear a prompt voice Wrong password please re enter The system default operate password is 888888 Make sure to enter the password firmly by pressing and holding one digit at a time so you can hear a beep for each key press You may need to hold keys for half a second at a time Press 1 arm if finished successfully you will hear a voice prompt System armed Press 2 disarm if finished successfully you will hear a voice prompt System disarmed Press 3 monitoring for 30 seconds to continue monitoring press 3 again for another 30 seconds You can cancel monitoring at anytime by pressing 1 to arm and 2 to disarm Press 4 two way intercom for 30 seconds You cannot o
21. on 24 hours regardless of your system s Arm or Disarm status This is recommended to be used for smoke detector panic button water leak sensor and temperature sensors only DO NOT set any door sensor or motion sensor as Emergency zone Home Zone Highlight it press Enter Default is YES if you select NO the zone will disable during home alarm status No recommended for motion sensor select Yes for all Window door sensors Chime Zone Highlight it press Enter Default is NO This function does not work with motion sensors Delayed Zone Highlight it press Enter Default is NO if set YES allows you to come back home and open the door without triggering the system System default delay alarm time is 45 seconds You can change this time by going to System Settings to set the Alarm Delay time Siren Enable Highlight it press Enter Default is YES if set NO siren will disable when this zone triggered no siren alarm will sound Note All zones are instant zones by Default Instant refers to the system being immediately armed if any zone is triggered when the system is in armed status Delete select it then press Enter you can find the target sensor and delete it The Motion Sensor will initialize itself during the first 1 3 minutes after the front cover is re attached DO NOT KEEP Cover open Do not test it during initialization You can walk 3 5 steps in front of motion sensors after initialization The LED will remain on for
22. perate the main unit console panel during this time You can cancel intercom at anytime by pressing 1 to arm and 2 to disarm Or just simple text message from you cell phone to Arm Disarm Home Arm History checking it Password follow by 1 for Arm i g 888881 Password follow by 2 for Disarm i g 8888882 Password follow by 3 for Home Arm I g 8888883 Password follow by 4 for History checking i g 8888884 Answer Alarm Call to prevent alarm call answered by voice mail you need manually answer the incoming alarm on your pre saved cell phone then press twice to stop call the second number Wireless Panic Button Option Program Panic Button If you received a pre Programed system kit please ignore this step and do not Q program it again Panic Button you need should be programmed to your console Pisecror Press PROGRAM button on console enter the default password 888 888 Use Scroll key to choose Sensor then press Enter on Console Then choose Add press Enter again then you will see Trigger Sensor trigger your Panic Button by pressing the Red circle button Then the console will request you to add a Zone Name for this sensor Input a name for this sensor then press SAVE You will see Record Sensor Name press Enter record a voice for this panic button Set the Panic button as Emergency zone use it in 24 7 regardless of console being Armed or Disarmed Press PROGRAM button on console enter the default password 888 888 use Scro
23. r Window Open Reminder Select it and press Enter If you set it to Yes you are not able to arm your system when doors or windows are left open It will remind you which zone door or window is open You must close it unless you arm the system by pressing LJ button and holding for 3 seconds to force system to be armed The default is set to NO This function will not work with GSMO6 console Note this function will only work when you use a remote keychain to arm your system You can still press the console s Arm key and input your password without this reminder warning Date Time Allows you to manually set your local date and time Priority Dial Telephone When you connect your console with dual networks Landline and GSM you may need to highlight Priority Dial Telephone Press Enter and highlight Yes then save it This function allows you to set your system to use your landline priority to call out and save your SIM card credit Note If someone cuts your landline the system will automatically call out from your SIM card If you only use SIM card please set this function as NO Language English Factory Reset lt Restore Defaults gt Allows you to set all functions as default without deleting your sensors and sirens so you do not need to reprogram again If you choose lt Format Systems it will go back to factory default and format all your settings including your sensors and sirens Then you will need to reprogram all sensors sire
24. ress back key until the console displays System Disarmed and the date time page Unplug siren from the power adapter and wait for 10 seconds to exit the setting mode Test Connect siren to the power adapter Press Emergency key on the main console You should hear the alarm sounding Caution f you plug and unplug the siren to the adapter consecutively and rapidly 5 times the siren will be deleted from the main console You will need to follow the steps above to reprogram Edit Select Edit and press Enter you will see all 3 siren names select a siren s name and press Enter You will then be able to change the siren s name Delete If you find system shows Space Full while you add extra siren or reprogram siren select Delete Delete all siren names Siren 1 Siren 2 and Siren 3 Then you can reprogram the sirens using above instructions Siren Enable Select Siren Enable If you set No the sirens will not give any alert for the entire system If you only want to quiet an individual zone s siren you have to go to Sensors menu and Edit it For details read Edit under Sensors Duration You can set wireless sirens to sound a continuous alert You can set it from 1 second to a maximum of 180 seconds Arm Disarm Tone Select Arm Disarm Tone and press Enter If you set Yes when you use the remote control to arm and disarm system you will hear a loud beep warning from the siren You can set No to turn
25. s sensor then press SAVE You will see Record Sensor Name then press Enter and record a voice for this sensor MAKE SURE ONLY ONE SENSOR IS TRIGGERED EACH TIME TO AVOID ANY ACCIDENTAL TRIGGERING OF A DIFFERENT SENSOR PLEASE KEEP ALL YOUR MOTION SENSORS IN DIFFERENT ROOMS AND MAKE SURE ALL WINDOW DOOR SENSORS ARE ATTACHED TO THEIR MAGNET PARTS IN CLOSED STATUS select it then press Enter you can use Auto search or Manual search to find your target sensor and high light it then press Enter to Edit Sensor Functions as below menu list Note if you don t know sensor name then choose Auto Search when you trigger an individual sensor and its name will be displayed on the console panel Select the sensor name and press Enter then you will see the menu displays as below MAKE SURE ONLY ONE SENSOR IS TRIGGERED EACHTIME TO AVOID ANY ACCIDENTAL TRIGGERING OF A DIFFERENT SENSOR PLEASE KEEP ALL YOUR MOTION SENSORS IN DIFFERENT ROOMS AND MAKE SURE ALL WINDOW DOOR SENSORS ARE ATTACHED TO THEIR MAGNET PARTS IN CLOSED STATUS Edit Zone Name Highlight Edit Zone name press Enter and you will be able to rename the sensor Record Zone Name Highlight it press Enter select Record you are able to record 5 seconds of your own voice If recording a sensor s name in your own voice this is what you will hear to identify that sensor when you receive an alarm call Emergency Zone Highlight it press Enter Default is NO f you set YES the zone will be
26. ss Enter you will see 60 directly input 2 digits for your delay setting You can change the setting to allow you enough time when you return home to disarm the system before it alarms Default is set to 40 seconds This Alarm Delay time only works when you set individual sensors as Delay Zones Otherwise it does not work l e disarm system press PROGRAM key then input password highlight Sensor and press Enter highlight Edit press Enter then highlight Manual Search and press Enter Choose the sensor name then press enter use scroll key to find Delay Zone then press Enter and check Yes save it Maximum is 60 seconds Landline Cut Warning Select it and press Enter If you set Yes during System Arm or Home Status the system will immediately go off and sirens will start alarming if an intruder cuts the landline or unplugs the landline jack Default is set as No Ring Time Before Answer Select it and press Enter you will see 1 flash directly input a digit for your ring count maximum is 9 This allows you to change the ring times for answering your regular home phone e g if you set it at 5 rings during 5 rings you can answer your regular home phone after 5 rings the alarm system will answer it The system will answer with the prompt Enter your password Then you can enter your password to control the system Press 1 to Arm system Press 2 to Disarm system Press 3 to listen in Press 4 to use console as an intercom press to end Doo
27. successful Step 3 Press Chime key to exit setting status During system disarm status you can press default password 1 2 3 45 6 followed by Enter key You will see Set indicator light on and Enter key flashing Then press 2 0 1 followed by an Enter key Send indicator light on move your target key chain the one that you want to add close to the keypad read area and you will hear a few short beeps meaning add successful You may add maximum 8 pieces RFID keys At the end press Chime key to exit setting status During system disarm status you can press default password 1 2 3 45 6 followed by Enter key You will see Set indicator light on and Enter key flashing Then press 2 1 1 follow by an Enter key It will auto delete all key chains You CANNOT delete one key chain each time If you lost any key chain please choose to delete all key chains then add other key chains again At end press Chime key to exit setting status Password followed by Arm key to arm system Arm indicator light on in solid Password followed by Disarm key to disarm System Open light on for 3 seconds depending on how long you set for door open time default 3 seconds Arm indicator light flashes once every second Password followed by Home key to arm system when you are at home Arm indicator light flashes once every 3 seconds Password followed by SOS for emergency Password followed by Chime key to change system to Chime status Use key chain to disarm
28. system directly without entering any password Other features During system disarm status you can press default password 1 2 3 45 6 followed by Enter key You will see Set indicator light on and Enter key flashing and press 5 0 T T T T for time from 01 to 99 seconds and Enter This time is for how long you need an access to door without triggering the alarm For example when you use a key chain or password to open the door how long you would want the door to be closed and system still be in arm status If you had a neighbor having the same system or other devices that interfere your system and always results in false alarm then during system disarm status press default password 1 2 3 45 6 followed by Enter key When you see Set indicator light on and Enter key flashing press 40 dddd any 4 digits pass code you do not need to remember this pass code it is only for encrypting the system with other device After setting up your keypad you may change the default password to your own password for safety During system disarm status you can press default password 1 2 3 45 6 followed by Enter key You will see Set indicator light on and Enter key flashing Then press 3 0 new password Enter repeat the new password follow by Enter one more time you may set new password up to 6 digits Then press Chime key to exit setting status Please keep your new password to a safe place and do not forget it If you forget your password re
29. tem kit please ignore this step and do not program it again Press PROGRAM button on console enter the default password 888888 Select Remote Controllers then press Enter on console You will see the following menu Add Select Add press Enter then you will see Trigger Controller Code press any button on your remote Keychain Nine digits will appear on console screen for 1 2 seconds This is the unique address for this keychain The console will request you add an owner s name for this remote Input a name for this remote and then press SAVE You will see Record Owner Name then press Enter and record a voice for this remote keychain Note Each time you press Add follow steps above You can add one remote and a maximum of 8 Keychain Remotes Edit Select Edit press Enter to find the name of the remote then press Enter again you can edit the remote keychain name or record a voice for the remote keychain Delete Select Delete and press Enter you can find all your remotes names to delete one or all remote keychains if you want to remove them from your console panel Delayed Arm If you select Delayed Arm and press Enter then set Yes you will have 60 seconds to leave the house Default sets Delay as Yes It gives you 60 seconds to leave the house when you arm system by remote keychains You can change this time using System Settings menu under Arm Delay time Program and Mount Bracket Door Window Sensors If you received a pre program
Download Pdf Manuals
Related Search