Leica DISTO™ D5
Contents
1. Storage 25 C up to 70 13 F up to 158 F 10 up to 50 14 F up to 122 F maximum deviation occurs under unfavourable conditions such as bright sunlight or when measuring to poorly reflecting or very rough surfaces Measuring accuracy between 10 m and 30 m may deteriorate to approx 0 025 mm m for distances above 30 m to 0 1 mm m In long range mode the maximum deviation from a distance of 30 m increases to 0 15 mm m Operation Measuring conditions Measuring range The range is limited to 200 m At night or dusk and if the target is in shadow the measuring range without target plate is increased Use a target plate to increase the measurement range during daylight or if the target has poor reflection properties Target surfaces Measuring errors can occur when measuring toward colourless liquids e g water or dust free glass Styrofoam or similar semi permeable surfaces Aiming at high gloss surfaces may deflect the laser beam and lead to measu rement errors Against non reflective and dark surfaces the measuring time may increase Leica DISTO D5 LCA782203a gb O Appendix Do not immerse the instrument in water Wipe off dirt with a damp soft cloth Do not use aggressive cleaning agents or solutions Handle the inst rument as you would a telescope or camera Warranty The Leica DISTO D5 comes with a three year warranty from Leica Geosystems AG More deta2. The area ofa triangle can be calculated by the measurement of three sides See drawing N Press the key three times the triangle symbol appears in the display Press the key and measure the first side of the triangle Press the key and measure the second side of the triangle Press the key and measure the third side of the triangle A The result is shown in the summary row Press and hold the hd key to display additional information about the y y measurement such as the angle included by the first two measu ge y rements and the perimeter AN of the triangle Stake out function 8 Two different distances a and b can be entered into the instrument and can then be used to mark off defined measured lengths e g in the const ruction of wooden frames Leica DISTO D5 LCA782203a gb Em Functions Ad Press this button twice and the following symbol appears in the display See figure Entering stake out distances Press this button four times and the stake out function symbol appears in the display LL By usin and you can adjust the values first a and then b to y 8 suit the desired stake out distances Holding the buttons down increases the rate of change of the values Once the desired value a IL has been reached it can be confirmed with the button Value b can be entered using and The defined value b LEE is confirmed with the button Pressing the but
3. Labelling Laser Radiation Do not stare into the beam Laser class 2 acc IEC 60825 1 2007 Maximum radiant power lt ImW Emitted wavelength 620 690nm Beam divergence 0 16 x 0 6 mrad Pulse duration 1 10 5 Position of the product label see last page Inserting replacing batteries See figure A Remove battery compartment lid and attach handstrap 2 Insert batteries observing correct polarity 3 Close the battery compartment again Replace the batteries when the symbol flashes permanently in the display Cg Remove the batteries before any long period of non use to avoid the danger of corrosion Cg We recommend the usage of AA size max 5 lithium batteries or rechargable NiMH batteries The Leica DISTO TM also works with Alkaline batteries but the battery lifetime will be reduced WARNING This Leica DISTO TM was delivered with high quality non rechargable lithium batteries Wrong usage of lithium batteries can be hazardous Precautions e Please do not recharge these batteries e Do not mix lithium batteries with other types of batteries Do not use batteries if their casing is damaged Changing the reference point multifunctional endpiece See figure B The instrument can be adapted for the following measuring situations For measurements from an edge fold out the positioning bracket until it first locks in place See figure For measurements from a corner open the po
4. during and after important measurements Make sure the Leica DISTO optics are kept clean and that there is no mechanical damage to the bumpers CAUTION In using the instrument for distance measurements or for positio ning moving objects e g cranes building equipment platforms etc unfo reseen events may cause erroneous measurements Precautions Only use this product as a measuring sensor not as a control device Your system must be configured and operated in such a way that in case of an erroneous measurement malfunction of the device or power failure due to installed safety measures e g safety limit switch it is assured that no damage will occur Safety Instructions Ea Leica DISTO D5 LCA782203a gb WARNING Flat batteries must not be disposed of with household waste Care for the environment and take them to the collection points provided in accordance with national or local regulations A The product must not be disposed of with household waste Dispose of the product appropriately in accordance with the national regulations in force in your country Always prevent access to the product by unauthorised personnel Product specific treatment and waste management information can be downloaded from the Leica Geosystems home page at http www leica geosystems com treatment or received from your Leica Geosystems dealer Electromagnetic Compatibility EMC The term electromagnetic compatibi
5. ADOBE ss tati ia iei ina mnt 14 e Measuring distances e Computing functions areas and volumes e Measuring tilts Prohibited use e Using the instrument without instruction e Using outside the stated limits e Deactivation of safety systems and removal of explanatory and hazard labels e Opening of the equipment by using tools screwdrivers etc as far as not specifically permitted for certain cases e Carrying out modification or conversion of the product e Use of accessories from other manufacturers without the express approval of Leica Geosystems Leica DISTO D5 LCA782203a gb EM Safety Instructions e Deliberate or irresponsible behaviour scaffolding when using ladders when measuring near machines which are running or near parts of machines or installations which are unprotected e Aiming directly into the sun e Deliberate dazzling of third parties also the dark e Inadequate safeguards at the surveying site e g when measuring on roads construction sites etc Limits of use er The Leica DISTO is designed for use in areas permanently habitable by See section Technical Data humans do not use the product in explosion hazardous areas or in aggres sive environments Areas of responsibility Responsibilities of the manufacturer of the original equipment Leica Geosystems AG CH 9435 Heerbrugg for short Leica Geosystems Leica Geosystems is responsible for supplying the product
6. a distance using 2 auxilliary measurements 7 See figure P e g for measuring building heights or widths It is helpful to use a tripod when measuring heights that require the measurement of two or three measurements Press this button once the display shows A The laser is switched on Aim at the upper point 1 and trigger the measurement After the first measurement the value is adopted Keep the instrument as hori zontal as possible Press and hold down this button to trigger continuous measurement 4 sweep the laser back and forth and up and down over the ideal target point Press to stop continuous measurement 2 The result is displayed in the summary line the partial results in the secondary line Press and hold the key to display additional information about the measurement of the angles of the triangle X1 and A Indirect Measurement determining a distance using 3 measurements See figure Q Press this button twice the display shows the following symbol A The laser is switched on A Aim at the upper point 1 and trigger the measurement After the pper p 88 first measurement the value is adopted Keep the instrument as horizontal as possible Press and hold down this button to trigger continuous measurement 4 sweep the laser up and down over the ideal target point Press to stop continuous measurement 2 The value is adopted Aim at the lower point and press this button to trigger
7. including the User Manual and original accessories completely safe condition addi tional language versions can be found at www disto com Responsibilities of the manufacturer of non Leica accesso ries The manufacturers of non Leica accessories for the Leica DISTO are responsible for developing implementing and communicating safety concepts for their products They are also responsible for the effec tiviness of these safety concepts in combination with the Leica Geosystems equipment Responsibilities of the person in charge of the instrument WARNING The person responsible for the instrument must ensure that the equipment is used in accordance with the instructions This person is also accountable for the deployment of personnel and for their training and for the safety of the equipment when in use The person in charge of the instrument has the following duties e To understand the safety instructions on the product and the instruc tions in the User Manual e familiar with local safety regulations relating to accident preven tion e To inform Leica Geosystems immediately if the equipment becomes unsafe Hazards in use CAUTION Watch out for erroneous distance measurements if the instrument is defective or if it has been dropped or has been misused or modified Precautions Carry out periodic test measurements Particularly after the instrument has been subject to abnormal use and before
8. instructions Program selection submenu Level Timer Measurement field Result bar Detailed display OP wir N Status bar with Laser ON Reference plane Display Long range mode Offset Plus Minus Battery status Display in digital pointfinder mode Digital pointfinder 4x zoom The device has an integral digital pointfinder which shows the target directly on the display The displayed crosshairs allow precise measu rements to be made even though the laser beam is not visible See drawing F 2 The integral coloured digital pointfinder is a great help outdoors and can be used in every function Longer distances and precise measurements on detailed surfaces can even be accomplished in bright sunlight without any problem The 4x zoom allows the image to be magnified to suit the user s requi rements Press the key to activate the function Press the key again to operate in a 1 2x or up to 4x zoom view The brightness of the camera can be adjusted through 5 levels using the key or the Leica DISTOTM D5 LCA782203a gb ESSE Start up Parallax errors occur when the digital pointfinder is used on close targets the laser dot may appear displaced in the crosshair In this case you should rely on the actual laser dot for targeting the object See drawing F 2 Zoom step 1 2x 4 2 Timer 3 Level in 4 Crosshairs 5 Inclination angle 6 Distance tracking value 7 Imag
9. the first length measurement 16 12 Press the key and take the second length measurement 1 and inclination angle measurement device measures inclination angles between 45 and 45 The result is shown in the summary row Press and hold the key to display additional information about the a trapezium measurement for example inclination angle trapezium E area 1 It measurement x E The inclination sensor measures tilts between 45 The infocode i 160 means that the device has been set outside the permissible limits During tilt measurement the instrument should be heldwithout a transverse tilt max 10 If the device is tilted by more than 10 laterally the display shows infocode i 156 which means that the device has been tilted too much The units of inclination are set in the menu OL Press this button once to activate the tilt sensor The 4 symbol 9 appears in the display The tilt is continuously shown as depending on the setting Press to measure the inclination and the distance See figure L Direct horizontal distance p P Press this button to measure tilt and distance The summary line displays the result as the direct horizontal distance Press and hold the key to display additional information about the measurement for example the inclination angle p the measured distance PA and the indirect height 1 See drawing Triangular area A
10. Area lt gt Press once The lt gt symbol appears the display Press this button to take the first length measurement lt gt e g length The result is shown in the summary row Press and hold the key to display the perimeter gt Volume 4 Press this button twice The 45 symbol appears in the display Press this button to take the first length measurement T e g length Press this button to take the second length measurement amp e g width Press this button to take the third length measurement Kl e g height The result is shown in the summary row A Press it again to take the second length measurement aleg width Press and hold the button to display additional room information such as ceiling floor area ef surface area of the walls circumfe rence lt gt Trapezium measurement 17 See drawing J Press the key once The symbol is displayed Press the key and take the first length measurement e g height 1 Press the key again and take the second length measurement e g width Press the key and take the third length measurement 1 e g height 2 The result is shown in the summary row Press and hold the key to display additional information about the O trapezium measurement for example inclination angle trapezium area A n Trapezium measurement 2 17 See drawing Press the key twice This symbol fj is displayed Press the key and take
11. ake the second measurement The device confirms the measurement with M The tilt sensor is calibrated Switching on and off Switches on the instrument and laser The display shows the battery symbol until the next button is pressed Pressing this button for longer switches the instrument off The instrument switches off automatically after six minutes of inactivity CLEAR button The last action is cancelled While making area or volume measu rements each single measurement can be deleted and remeasured in series Reference setting The default reference setting is from the rear of the instrument Press this button to take the next measurement from the front edge f TT special beep sounds whenever the reference setting is changed After a measurement the reference returns automatically to the default setting rear reference See figure Press this button for longer the front reference is set permanently Press this button the rear reference is set again Operation EE Leica DISTO D5 LCA782203a gb Measuring Single distance measurement Press to activate the laser Press again to trigger the distance measu rement The result is displayed immediately Minimum maximum measurement This function allows the user to measure the minimum or maximum distance from a fixed measuring point It can also be used as determine spacings See figure I It is commonly used to measure room diagonals max
12. ant and then press the button to enter it into your calculation Historical storage Press this button twice and the previous 20 results measurements or calculated results are shown in reverse order The and buttons can be used for navigation Press this button to use a result from the summary line for further calculations Pressing the and buttons at the same time erases all the values in historical storage Leica DISTO D5 LCA782203a gb EE Functions Timer self triggering Press this button to set a 5 second time delay or Press and hold down this button until the desired time delay is reached max 60 seconds Once the key is released with the laser activated the remaining seconds until measurement e g 59 58 57 are displayed in a countdown The last 5 seconds are counted down with a beep After the last beep the measu rement is taken and the value is displayed timer can be used for all measurements Appendix Message codes All message codes are displayed with either 1 or Error The following errors can be corrected Transverse tilt greater than 10 Hold the instrument without any transverse tilt Main tilt direction angle too high gt 45 The calibration has not been Calibrate the device on an abso accomplished on a leveled lute horizontal leveled surface surface and the calibration value is respecitvely within an ELLE 252 Er Measure angle
13. dao Leica DISTO 5 The original laser distance meter Ta Warranty e PS Geta C ali when it has to be right eua D dana ne Geosystems 000 000 000 000 Leica DISTO D5 User Manual Safety Instructions English Symbols used Congratulations on the purchase of your Leica DISTO DS The symbols used in the Safety Instructions have the following meanings Carefully read the Safety Instructions and the User A WARNING AN Manual before using this product Indicates a potentially hazardous situation or an unintended use which if not avoided will result in death or serious injury CAUTION Indicates a potentially hazardous situation or an unintended use which if not avoided may result in minor injury and or in appreciable material financial and environmental damage Contents amp Important paragraphs which must be adhered to in practice as The person responsible for the instrument must ensure that all users understand these directions and adhere to them Safety Instructions they enable the product to be used in a technically correct and efficient SCENE 4 manner Menu 2 42 0400000 6 ri 8 Use of the instrument CS CNI IE 9 Le qu M 9 Permitted use
14. e 3000 yd Setting the unit for tilt measurements The following units can be set for tilt measurements Display illumination The brightness of the display has six levels of adjustment Step 6 is the brightest and step is the darkest setting Long range Mode ly Unfavourable conditions strong sunlight or a very weak reflective target surface may reduce the range of the device in spite of this the long range mode allows you to take measurements over longer distances The use of a tripod and measurement initiation by pressing the key are recom mended when measurements over 30m are made over longer time periods in these conditions For details see Technical specifications settings are reset when the device is switched off Measuring with the tripod The reference point be adjusted to the tripod mount if the user requires a measurement from the actual mounting grommit versus the front or back of the DISTO To do this select the item You can switch the reference on the tripod on or off The setting can symbol in this menu be seen on the display 1 CE We recommend that measurements are initiated using the key when using the device on a tripod in order to prevent loss of sharp ness settings are reset when the device is switched off Beep 0 You can switch the beep on or off Offset 441 An offset adds or subtracts a specified value automatically to or
15. e Menu functions Settings Various device settings can be made in the menu vertical list shows each entry In this menu the selection field cursor remains stationary and the list moves in a vertical direction Starting from the centre of the list the priority of list entries starts at the top and fans out clockwise See drawing G The menu contains following items Units of measurement distance 2 Units of measurement angle 3 Display illumination 4 Long range mode 5 Tripod 6 7 Offset 8 Digital Pointfinder image in black white 9 Level in status field in IO Reset Calibrate tilt sensor Navigation in the menu The menu allows settings to be customized for a particular user or applica tion General description Press and hold the key to enter the Setup menu By pressing the or keys navigate through the main menu items in the menu Press the key briefly to enter the submenu of the selected main menu item By pressing the Or keys you can make the alterations in the submenu Press and hold the key to accept the settings Pressing the button for longer in the menu allows you to quit the settings function without saving Menu functions O 6 Leica DISTO D5 LCA782203a gb Setting the unit for distance measurements The following units can be set Distance _ Volume 0 0000 m 0 000 m 0 000 m 1 2 0 0 M 12 14 15 EH 2 000 m Bom 008 ow
16. from all measurements This function allows tolerances to be taken into account e g unfinished dimensions compared with finished dimensions If you selected the Offset function in the menu you can now adjust the value using the or the key Pressing the key for longer increases the rate of change of the values When you reach the desired offset value confirm it with the key The display shows the appropriate symbol Or for as long as the offset value is set Leica DISTO D5 LCA782203a gb Emme Menu functions Digital Pointfinder image black white Sy The display in pointfinder mode can be changed to black white Level in status field z The Level in in status field can be switched on or off Reset returning the instrument to the factory settings C7 RFRFT The instrument has a Reset function If you select the menu function Reset and confirm the device returns to the factory settings and stack and memory are deleted X All customised settings and stored values are also lost Calibrate the tilt sensor You can calibrate the tilt sensor in the device Calibration requires two measurements on a level surface Select calibration mode in the menu H Carry out a first measurement on a level surface The device confirms the measurement with mil 2 Rotate the device horizontally through 180 Ea 3 Press the key and confirm that the device was rotated through 180 4 Press the key and t
17. iled information can be found at www disto com All illustrations descriptions and technical specifications may be subject to change without prior notice To receive the three year warranty the product must be registered on our website www disto com within eight weeks of the purchase date If the product is not registered a two year warranty applies Appendix O Leica DISTO 25 LCA782203a gb UNIT o i 69 este Leica DISTO D5 10 al ant to SWISS T by Leica Geosyst WWW TOM ISO 9001 ISO 14001 CH 9435 Heerbrugg Leica Geosystems AG Heerbrugg Switzerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Systems ISO standard 9001 and Environmental Management Systems ISO standard 14001 Total Quality Management Our commitment to total customer satisfaction Ask your local Leica Geosystems agent for more information about our TOM program Printed in Switzerland Copyright Leica Geosystems AG Heerbrugg Switzerland 201 Tra
18. imum values or hori zontal distances minimum values Press and hold down this button until you hear a beep Then slowly sweep the laser back and forth and up and down over the desired target point e g into the corner of a room Press to stop continuous measurement The values for maximum and minimum distances are shown in the display as well as the last measured value in the summary line Laser continuous Press and hold down the key when switching on the device until the character appears permanently in the display and a beep sounds Every further press of the key releases a distance measurement Press the key and keep it pressed to switch the device and Laser continuous operation off Leica DISTO D5 LCA782203a gb e If the laser is in continuous operation mode the device switches off automatically after 15 minutes Functions Overview of the program icons Measurement Detail display 1 2 3 1 2 3 sh Volume measurement o lt 28 I using three distances wa Trapezoid measurement 2 using two distances d E 4 ni lt Measuring Addition subtraction Distance measuring The next measurement is added to the previous one The next measurement is subtracted from the previous one This process can be repeated as required Press this button and the result is then always shown in the summary line The last step is cancelled
19. lity is taken to mean the capability of the product to function smoothly in an environment where electromagnetic radiation and electrostatic discharges are present and without causing electromagnetic interference to other equipment WARNING The Leica DISTO TM conforms to the most stringent requirements of the relevant standards and regulations Yet the possibility of it causing interference in other devices cannot be totally excluded CAUTION Never attempt to repair the product yourself In case of damage contact the local dealership Leica DISTOTM D5 LCA782203a gb Safety Instructions Laser classification Integrated distancemeter The Leica DISTO produces a visible laser beam which emerges from the front of the instrument It is a Class 2 laser product in accordance with EC60825 1 2007 Radiation safety of laser products Laser Class 2 products Do not stare into the laser beam or direct it towards other people unnecessarily Eye protection is normally afforded by aversion responses including the blink reflex WARNING Looking directly into the beam with optical aids e g binoculars telescopes can be hazardous Precautions Do not look directly into the beam with optical aids CAUTION Looking into the laser beam may be hazardous to the eyes Precautions Do not look into the laser beam Make sure the laser is aimed above or below eye level particularly with fixed installations in machines etc
20. nslation of original text LCA782203a Pat No WO 9427164 WO 9818019 WO 0244754 WO 0216964 US 5949531 EP 1195617 US 7030969 WO 03104748 Leica Geosystems AG when it has to be right Seica Switzerland www disto com Geosystems
21. sitioning bracket until it locks in place then push the positioning bracket lightly to the right to fold it out fully See figure D A built in sensor automatically detects the orientation of the positioning bracket and adjusts the zero point of the instrument accordingly Leica DISTOTM D51CA782203a gb Start up Keypad See figure E ON DIST On measuring button Digital pointfinder button Timer button Plus button Minus button Area volume button Indirect measurement Pythagoras button O Trapezium button o Functions button 10 Reference button Storage Memory button 12 Clear Off button 13 Menu Equal button Display in normal mode See drawing F I The graphics screen of the measurement window is split into different areas Top left is the brightest field which contains the currently selected measuring program Just to the right appears the program submenu which shows the measuring programs that can be selected by pressing the same key the required number of times The measurement field contains the individual measurements of the measuring program with reference to a series of separate distance measu rements Three lines are provided for this A horizontal line separates the measurement field and the result bar from one another A red triangle indicates whether the selected measuring program has a detailed display available Program selection with measurement
22. the measurement 3 a lt The result is displayed in the summary line the partial results in the secondary lines Press and hold the key to display additional information about for example the partial distances 4 Indirect measurement determining a partial value using 3 measurements 1 See figure e g determining the height between point and point 2 using three target points Press this button three times the display shows the following symbol A The laser is switched on Aim at the upper point 1 Press this button and trigger the measurement 4 After the first measurement the value is adopted Triggers the measurement A After the second measurement the 4 and the minimum distance 24 value is adopted Press and hold down this button to trigger continuous measurement GB A Sweep the laser up and down over the ideal target point Press this button to end continuous measurement The result is displayed in the summary line the partial results in the secondary lines Press and keep pressed the key to display additional information about the measurement of the partial lengths Storage of constants historical storage Storage of a constant You can store and recall a frequently used value e g height of a room Measure the desired distance press and hold the button until the device beeps to confirm storage Recalling the constant Press this button once to recall the const
23. ton starts the laser measurement The display shows required stake out distance in the summary line between the stake out point first a and then b and the instrument rear reference If the DISTO TM is then moved slowly along the stake out line the displayed distance decreases The instrument starts to beep at a distance of 0 1 from the next stake out point The arrows in the display indicate in which direction the DISTO needs be moved in order to achieve the defined distance either a or b As soon as the staking out point is reached the symbol appears in the display The function can be stopped at any time by pressing the button Indirect measurement The instrument can calculate distances using Pythagoras theorem This procedure is helpful if the distance to measure can not be reached directly amp sure you adhere to the prescribed sequence of measu rement e All target points must be a horizontal or vertical plane The best results are achieved when the instrument is rotated about a fixed point e g with the positioning bracket fully folded out and the instrument placed on a wall or the disto is mounted on a tripod The minimum maximum function can be used see explanation in Measuring gt Minimum maximum measurement The minimum value must be used for measurements at right angles to the target the maximum distance for all other measurements Indirect measurement determining
24. up to max 45 ineligible area measurement time too long distance gt 100 m S foes pad plate background brightness too high rent lighting conditions 260 1 beam interrupted Repeat measurement Receiver signal too weak Switch on off the device several times If the symbol still appears Hardware error then your instrument is defec tive Please call your dealer for assistance Appendix IEEE Leica DISTO D5 LCA782203a gb Technical data Distance measurements Measuring accuracy up to 10 Ww 2 6 standard deviation typically 1 0 mm Power Range Technology Range use target plate from about 100 m Smallest unit displayed Minimum maximum measurement Conti nuous measurement 0 05 m to 200 m Area volume calculation of room data Addition subtraction Indirect measurement using Pythagoras Tilt measurements Tilt sensor Accuracy 2 o standard deviation to laser beam to the housing Indirect measurement using tilt sensor direct horizontal distance Angle measurement using tilt sensor 45 General Laser class GS om lt T mW at distances 10 50 100 m Historical storage 20 values Tripod thread Type 1 4 20 Battery life up to 2 x 5 5 000 measurements Protection against splashes and dust IP 54 dust proof splash proof Weight with batteries 195 g 143 5 x 55 x 30
Download Pdf Manuals
Related Search