Home

SK720 Flybarless System - User Manual

Contents

1. Ready for Flight Save your setup to your computer s hard drive by selecting Save Setup from the File menu then go to Section 12 of this manual 2011 Skookum Robotics Ltd 44 12 How to Check Cyclic Pitch amp Phasing NOTE The gyro must be put into setup mode before the cyclic throws phasing and swash motion can be checked for correctness Place the gyro into setup mode by connecting it to an SK LCD Terminal or to a computer using a USB cable A slowly flashing green LED on the SK720 indicates that the gyro is in setup mode The goal of mechanical and gyro swashplate setup is to retain your normal collective blade pitch range while setting a cyclic range of about 10 degrees This is important Cyclic pitch is the blade s pitch due to aileron or elevator input While in setup mode control stick motions are sent directly to the swashplate and tail rotor as if stability gains were zero i e the gyro only does its mixing function The gyro s gains will have no effect in this mode To check the cyclic range and phasing 1 Set collective pitch to zero 2 Align a blade along the fuselage pointing over the nose and tail of the helicopter as in Figure 12 1 below lt Blade Aligned Over Boom Figure 12 1 Cyclic Aileron Roll Phasing 3 Now try full nose up elevator control with the aileron centered Measure the pitch of the blade that extends over the nose If the mechanical setup is ideal the blade sho
2. z Tail Gain Ch Gear Auto Trim at Init Misc C Enable Logs Low Yoltage Alarm BEC C Upside Down _Send Setup Fl Figure 7 4 SK720 Setup Software Main Window If the software will not run on your computer make sure that you have the latest version of Windows NET Runtime installed Check the Microsoft website for the most recent edition The nitial Configuration Wizard will start automatically the first time you start the software Follow the tutorial wizard s steps to easily set up your SK720 If the nitial Configuration Wizard does not start automatically you can also start it by selecting nitial Configuration Wizard from the Wizards menu 2011 Skookum Robotics Ltd 14 8 Mounting the Gyro The gyro unit can be mounted upside down backwards or rotated 90 degrees but it must be level and have its sides aligned as accurately as possible with the fore aft axis of the helicopter as shown in Figure 8 1 By default the servo port end of the unit is the front end It can be installed in other orientations but the SK720 label must always face up or down Note that misalignments of even a few degrees 2mm or 1 16 difference between the front and back edges of the case may cause problems with tuning the gyro The gyro should also be as far as possible from any heat sources and at least 10 cm from Xtremelink receivers Aligned at 90 angles to frame Figure 8 1 SK720 Mounti
3. 2011 Skookum Robotics Ltd 75 Hiller Gains This gain s effect is similar to heading hold on a yaw gyro Higher Hiller Gain is equivalent to increasing the weight of a flybar s paddles and adds stability and resistance to wind gusts This feature gives the heli a locked in feel Slop free linkages rigid rotor head mechanics stronger servos and stiff blades allow higher gains here When hiller gain is too high the heli will oscillate at 1 2 cycles per second Damping Gains Roll and pitch rate motion damping Higher gain helps with stability and is equivalent to having heavier rotor blades or a higher head speed Fast digital servos allow higher gains here The default gains are best for analog servos but can be set to 20 16 for digital servos When damping gain is too high the heli will oscillate quickly Tail Drag Compensation All helicopters have uneven drag on their airframes especially the tail use this setting to trim out the effect of tail boom drag for better piros and tick tocks Lock Cyclic Gain This allows you to lock in the value for overall cyclic gain which the gyro uses to scale the Hiller and Damping gains The gyro will then only pay attention to the gain channel for selecting this bank but it will ignore the value the channel has Cyclic Gain Channel Also Scales Damping Gain If enabled then the Cyclic gain channel will also adjust the damping gains by the ratio of the Cyclic Gain input vs the e
4. You will then be able to switch between active Cyclic banks to enable disable self levelling If you use this method it is best to copy all of your settings from your primary Cyclic tab to your bail out Cyclic tab if you intend to set up a bail out mode Do this by right clicking the mouse on your primary cyclic tab to bring up a popup menu Choose Copy Cyclic 1 to Cyclic 2 as shown in Figure 15 2 below Offline Setup Values Control Drive System Swashplate Swash Servos Tail Servo Cyclic 1 Cyclic 2 Tail1 Tail 2 Cyclic Gains and Rates Control Rates J 240 deg s Reset Cyclic 1 to Default Sport Setup Reset Cyclic 1 to Default Scale Setup Reset Cyclic 1 to Default Baisc3D Setup Self Leve RMSE OS o Q Copy cyclic 1 to Cyclic 2 Hiller Decay lt J Load Cyclic 1 Settings From File C Lock Cyclic Gain to Figure 15 2 SK720 Setup Software Cyclic Tabs with Popup Menu CAUTION Ensure that your trims are set the same in both gain banks on your transmitter if one bank is to be used as a bailout mode 2011 Skookum Robotics Ltd 54 16 Basic Tuning Definitions e Tail gain adjusts the holding ability of the gyro in yaw rudder e Cyclic gain adjusts the stability and holding ability of the gyro for aileron roll elevator pitch Follow these steps 1 2 3 4 5 6 As a starting point for most helicopters adjust the gains to about 50 for the Cycli
5. right The Gyro Rate for Aileron should be positive and show green 2011 Skookum Robotics Ltd 36 e Repeat for the Rudder yaw axis but slowly rotate the helicopter nose right clockwise The Gyro Rate for Rudder should be positive and show green Offline Setup Values x m Control Drive Systeri Swashplate Swwash Servos Tail Serva Cyclic Cyclic 2 Tail 1 Tail 2 Radio Input Options Stick Deadbands Type SpektrumAJR Sateli gt Elevator Alleron 20 2 Cyclic Gain Ch Rudder 20 Tail Gain Ch Auto Trim at Init Kise Servo Bus is pointed Forvard ka Upside Down of C Enable Logs Low Yoltage Alarm BEC wt Figure 11 4 Setting Gyro Mounting Orientation Step 5 Swash Mixing Servo Setup NOTE The SK720 will not provide any stabilizing action while in set up mode This enables mechanical set up and servo trimming e Click the Swashplate tab in the Offline Setup Values area in the lower half of the setup software window see Figure 11 5 below Set the Swash Type just as you normally would in your transmitter Offline Setup Values a Swas h Type c Swash Mixing Hix Revr 120 Degree eCCPM 135140 Degree eCCPM O mCCPM 1 Serva go Degree eCCPM 3 or 4 servo Options Phase Trim deg Swash Ring Piro Comp Elevator Cyclic L R Aileron Cyclic Collective Pitch 4 E Figure 11 5 Offline Setup Values Swashplate Tab 2011 Skookum Ro
6. you can also play back logs by double clicking directly on the SKL file name in any Windows Explorer window NOTE Only logs containing actual flight time will be played back 2011 Skookum Robotics Ltd 61 When the 3D viewer starts you will see a window similar to the one shown in Figure 18 3 below There are four buttons at the bottom of the 3D viewer window that are used to control playback In order they are Stop Play Pause Fast Forward and Mute The Play button changes into a pause button while playback is in progress The white and gray progress bar may also be used to control playback You can jump forward or backwards in the playback sequence by clicking on the progress bar with your mouse 253 LOGO BIN SK720 Digital Flybar Playback Figure 18 3 3D Viewer Window As with the self leveling feature accurate playback is dependent on good mechanical setup of your helicopter High vibration will negatively affect the accuracy of the helicopter s calculated motion particularly the way in which it is shown to maneuver around the 3D viewer s virtual sky In cases of high and extreme vibration the helicopter will not be shown to fly around the sky at all Instead it will be displayed at a fixed location in front of the viewer Only the rotations pitch roll and yaw will be modeled in that event If your helicopter is experiencing high vibrations in flight a warning will be displayed on the playback screen in
7. B 6 AXIS CONTROL a Gta g aT ANgp S A SW A K oe i SKOOKUM M SW R ROBOTICS SW C TAIL JL Use the SK PW7 Power Bus if you intend to use high voltage 8 4V servos together with any 5 0V equipment on your helicopter 10 7 Optional Connections Power Bus We strongly recommend that you use the optional SK PW7 Power Bus for helicopters with blades longer than 500mm 20 inches This accessory isolates the SK720 from vibration carried by heavier servo cables and is capable of handling 20 amps of continuous current to eliminate brownouts The SK PW7 Power Bus also makes it possible to neatly install both 8 4V and 5 0V equipment on the same helicopter See the separate SK PW7 Power Bus manual for details on how to connect your receiver SK 720 and servos using the SK PW7 power bus 2011 Skookum Robotics Ltd 31 RPM Sensors CAUTION Be sure to activate the RPM sensor from the PC setup software before connecting your RPM sensor Your RPM sensor could be damaged if you don t See Section 11 of this manual for information about how to set the SK720 for use with an RPM sensor With an RPM sensor connected your helicopter s flight logs will include RPM data Once set the RPM sensor connects to port IO C Most hall effect base sensors will work but be careful with sensors from Eagle Tree Wiring on Eagle Tree sensors is non standard but they should work normally if you switch their red and black leads Mis
8. Setup Software amp Advanced Features Guide The main window of the setup software is broken down into three areas e The menu bar provides access to the program s features and functions e The Live Data region is updated in real time whenever the gyro is connected to your computer with a USB cable e The Offline Setup Values tabs display the values for your gyro s current helicopter setup file settings NOTE This section is for reference only You do not need to read or understand everything that is in it to use your SK720 Menu Bar Items in the File menu include Load Setup Click this menu item to load a setup from your computer s hard drive The Offline Setup Values tabs will be updated with newly loaded setup Any setup sent to the gyro will be labeled with the first 16 letters of the configuration file s Windows filename Save Setup Use this menu option to save a setup to your computer s hard disk This feature is useful if you want to experiment with different settings or backup your current settings to disk Reset to Sport Setup Use this menu item to reset the SK720 settings to the default sport setup Reset to Scale Setup Use this menu item to reset the SK720 settings to the default scale setup Reset to Basic 3D Setup Use this menu item to reset the SK720 settings to the default basic 3D setup Upgrade From SK360 Use this menu item to import a stored SK360 configuration file into the SK720 configurat
9. as landing gear lights or external governors to IO B IO C IO D and IO E Connect your SK LED or Swash Setup Type SW C_ SW R_ SW L_ SW A_ 120 135 140 eCCPM other external LED to the EX LED port If your helicopter has blades 500 mm 20 inches or larger you should use the optional SK PW7 Power Bus to isolate your SK720 from vibration and to supply your servos with sufficient electrical current to prevent brownouts Please see the separate SK PW7 Power Bus manual for more details on how to connect it 1 servo mCCPM 90 deg eCCPM Left Right means the heli s left and right when viewing the helicopter from its tail to its nose On 120 135 or 140 eCCPM swash plates The SW C servo can be located either at the front or back of the swash both are equivalent BSC and throttle servo control are only available via the SK720 when using satellite receivers Otherwise these devices must be connected directly to your traditional receiver 2011 Skookum Robotics Ltd 29 2011 Skookum Robotics Ltd 30 10 6 Howto Power the SK720 The allowed voltage range for your SK720 is 5V to 10V The SK720 can be connected to a battery or BEC by plugging it in to any open servo port except the IO D E or the EXT LED ports All other ports circled in the image below are connected to a joined power rail Just one of these ports needs to be connected to a battery or BEC amp x LED zp ID D amp E ID C a IO
10. different Folder click Browse and select another folder Click Next to continue Destination Folder CiProagram FilesiSkK 20 Digital Flybar Space required 35 7MB Space available 42 766 Cancel Figure 7 3 SK720 Configuration Program Installation Folder Screen After installing and starting the SK720 setup software on your computer plug your SK720 into any available USB port using the supplied USB cable The setup software will automatically detect the gyro The Connected indicator in the top left corner of the setup software should turn green and the gyro s serial number and firmware revision should also be displayed See Figure 7 4 on the next page 2011 Skookum Robotics Ltd 13 25 Untitled SK720 Digital Flybar File View Wizards Utility Preferences Help Connected _ Gyro Serial 4242 Firmware Rev 27 00 Live Data Inputs from Receiver Yaw Sensor Gyro Motion Elevator ea Elevator 0 degs Ailerorn 2 Aleron OD deg s Rudder ok Rudder 0 deg s Collective i Greet Nose Up Bank Aigi Cyclic Gain Orientation Tail Gain Level Offline Setup Values ez a Contral Drive Syster Swashplate lL Swash Servos Tail Servo I Cyclic 1 IL Cyclic Tail 1 Tail 2 Radio Input Options Stick Deadbands Gyro Mounting Orentation Type Spektrum lAi Satelli Bim Elevator 20 x Servo Bus ts pointed a Aileron 20 3 x Forward v Cyclic Gain Ch Aux 3 l ee 7 I udder
11. flight logs The Gear Ratio box will be enabled when the RPM sensor is selected on Enter a value in the Gear Ratio box to calibrate your sensor to your main rotor RPM Counter Clockwise Rotor Click this checkbox to tell your SK720 that your helicopter s main rotor rotates counter clockwise 2011 Skookum Robotics Ltd 69 Swashplate Tab The Swashplate tab is found in the Offline Setup Values region of the main SK720 setup software window as shown in Figure 19 4 below Offline Setup Values Swash Type 120 Degree eCCPM C Swash Mixing j Hix Hey Elevator Cyclic F 135140 Degree eCCPM ini Heron Cyclic O mCCPM 1 Servo E a i i 45 B go Degree eClPM 3 or4 servo pore Fitch Options Phase Trim deg Swash Hing Piro Comp Figure 19 4 SK720 Setup Software Swashplate Tab Swashplate Type Select your swashplate and mechanical mixing type Options are 120 eCCPM 135 140 degree eCCPM 90 degree mechanically mixed separate servos for each of elevator aileron and pitch control and 90 degree 3 or 4 servo eCCPM where servos are directly connected to the swash but 90 degrees apart Swash Ring Limits motion of the swashplate to prevent binding when large amounts of both elevator and aileron cyclic are used i e assume the swashplate is round not square Piro Comp Compensates for the effects of rapid yaw rates on cyclic stability This is important for 3D stunts and when flying in wind Mixing The inputs t
12. fly The SK720 will also pump the swashplate once after it initializes properly The gyro will not finish initializing until it is allowed to stand completely still for several seconds An uninitialized SK720 will be able to fly but the helicopter might not be in trim Always verify that the LED indicator is showing solid green before taking off to avoid flying in an out of trim condition LED State Meaning Slow Green Setup Mode Fast Green USB File Transfer Solid Red Flight Mode Initializing Solid Green Flight Mode Ready to Fly Green with Red Flicker Flight Mode High Vibration Warning Flashing Red Error State Alternating Red Green Firmware Updating Do Not Disturb 2011 Skookum Robotics Ltd 7 A rapidly flashing red LED light indicates an error or warning The most common causes are 1 The cyclic stick wasn t centred during gyro initialization in flight mode 2 Your helicopter has onboard electrical system voltage problems 3 Itis too hot or too cold 4 The Micro SD card failed to initialize Simply restarting the unit will clear these faults most times If the faults do not clear after resetting the unit please contact technical support NOTE The setup software will display the error state that caused the LED to flash red Errors are shown in magenta in the Live Data area Warnings are shown in yellow in the Live Data area Connect the gyro to the setup software using the USB cable to find the
13. for accurate control Suitable for 120 135 140 and 90 degree eCCPM as well as mCCPM swashplates Works with 2 3 4 or 5 blade rotor heads because phase is adjustable Swash Ring anti binding algorithm Expansion port for future accessories such as GPS Optional 20 amp external power bus for over 50 size and nitro helis 3 axis accelerometer 3 gyros allowing self levelling High power 32 bit processor for future upgradeability Up to 10 servos one tail servo 4 digital or analog swash servos and 5 other analog servos Port for a remote LED which can be mounted outside of the canopy e Built in 2 GB USB mass storage device Connect the unit to your computer without having to install drivers e Flight data logs can be played back on your PC Enables tuning of helicopter health e Compatible with the Skookum SK LCD terminal e Supports most tail servos by name in the setup software e Tutorial Wizards show how to use the setup software and help first time users set up their new SK720 e Existing SK360 setup files can be easily converted for the new unit 2011 Skookum Robotics Ltd 3 2 Package Contents Your gyro package includes SK720 Gyro unit Three vibration damping mounting pads One USB cable Warranty amp Quick Start Card 2011 Skookum Robotics Ltd 3 Getting Started The SK720 has a standard mini USB port located on the back of the unit Connect your new SK720 to your PC using the included USB cable The
14. gain percentage for any bank see Figure 11 10 The gain channel will then select which bank is active but won t affect the gains For example Table 11 1 Using Locked Gain Values With a Single Gain Channel The gain channel s endpoint setting in your transmitter will set the amount of gain for that function For example setting your gear channel s end points to 40 and 50 will give you 40 gain on one bank and 50 gain on the other This 1s illustrated below Bank 1 Bank 2 ules endpoint endpoint Gain Channel 2011 Skookum Robotics Ltd 43 Tail Banks With Only One Gain Bank Channel Selects banks Endpoints do not set either gain Not Locked Selects banks Endpoints set the Tail Gain Selects banks Endpoints set the Cyclic Gain Not Locked Not recommended Both scaled together Step 8 Check that your radio can select which tail and or cyclic bank is active as indicated by a small blue bar over each setup tab The small blue bar shows which switch position corresponds with which cyclic and tail gain tab Alternatively you can choose to use only one cyclic and or tail bank by selecting None in the Cyclic Gain Channel and or Tail Gain Channel fields see Figure 11 9 Choosing this option will result in the gains being locked on the associated tab See Section 16 of this user manual for detailed description of how to use the features in the Cyclic and Tail gain banks to tune your helicopter
15. it in to your computer Access files that are stored on the SK720 just like you would any other file on your computer Look for a file on the SK720 drive labeled SK720_ setup See Figure 7 1 below SK720 G SE od File Edit View Favorites Tools Help J J wi P Search Key Folders x i ies Address e G v Go Name Size Type Date Modified 5K720 CFG 1KB CFGFile 08 12 2009 09 45 p 5K720_Manual pdf 928KB Adobe Acrobat Doc 03 01 2010 12 50 P 5k720_5etup exe 5 282 KB Application 05 01 2010 17 17 Figure 7 1 SK720 Built in Flash Drive 2011 Skookum Robotics Ltd 11 Install the SK720 setup software onto your computer by double clicking on the installation program name You will then be presented with a window similar to the one shown in Figure 7 2 below 5 K720 Digital Flybar v3 00 Setup Saks a VY YY EE LY Choose Components INS MAGG Choose which features of SK720 Digital Flybar v3 00 you want ko ROBOTICS istal Check the components you want ta install and uncheck the components vou don t want bo install Click Next to continue Select components ta install 5K720 Digital Flybar GUI Skookum Robotics Data viewer SE720 Digital Flybar 30 Flight Data Playback Desktop Shortcut Check For Microsoft WET Runtime Open Virtual Audio Driver Fal aw tooo 1 She et wa Description Space required 35 7MB Figure 7 2 SK720 Configuration Program Installation Options Screen There a
16. rate mode Set the hold gain to about 60 for heading hold mode 2011 Skookum Robotics Ltd 80 20 Trouble Shooting Guide Symptom Problem amp Solution Symptom Problem amp Solution The SK720 stays in initialization The heli must be stationary and not RANGOMJINEF Or JUMPS ITON Vibration erges on the gyro Make sure mode LED stays red won t go vibrating for the unit to initialize This and pitch or tilts at one it is mounted on good damping tape green symptom can also be caused by large particular rpm and doesn t contact the frame Also amounts of electrical noise check for tail rotor vibration Helicopter tends to drift feel Hiller gain is too low Can not set Hiller very high Lack of servo speed and or precision loose in elevator and or aileron l without causing oscillation Rotor head mechanics should use full 3 l ee chai E EE Hiller gain is too high Aileron or Elevator don t give Increase Control Rate gains You will conmand e roleased he l fast enough roll and pitch rates then likely have to increase the Bell helicopter oscillates slow gane 2y a Proporiona amaun eae a TE Aileron or Elevator give roll and Decrease Control Rate gains and then ine nelceptek PRCHES Up OrGOWN Cyclic feels mushy in the centre Reduce control dead band momentary Not perfectly locked in h Try higher control dead band Helicopter tends to oscillate Damping gain is too high S ae ge eUS a Cea A rapidly Test by giving a sharp Heli
17. s controls Loss of control of the helicopter may result if the SK720 is mistuned or set up incorrectly See Appendix C for warranty information Always test fly in an area away from spectators and keep yourself at a safe distance when flying the helicopter especially after any change in the gyro s setup or tuning DO NOT stand closer than 10m 30 feet from the helicopter during test hovers or any other flying Keep bystanders clear of the flight area at all times WARNING Always safe the motor before you use the PC setup software or SK LCD terminal to set up or tune your SK 720 Basic safety practice is to kill the engine on a nitro RC helicopter or disconnect the motor or main battery on an electric RC helicopter whenever the heli is behind the flight line or is being adjusted in any way 2011 Skookum Robotics Ltd 6 5 Modes LED Indicator and Power Up The two primary modes are Setup mode and Flight mode The SK720 will automatically switch to setup mode whenever it is connected to a PC by a USB cable or connected to an SK LCD Terminal While the SK720 is in setup mode it will do the control mixing for the helicopter but it will not provide any stabilizing action This enables mechanical setup and servo trimming While in this mode the indicator LED will slowly flash green In Flight mode the LED Indicator will show solid red while the SK720 initializes and it will turn solid green once the SK720 is ready to
18. the ground before it will save the auto tuned gains to its memory To ensure that it saves its memory do not turn off the power to the SK720 until after the helicopter has been still for 5 seconds after the blades have stopped turning and the engine 1s off WARNING Observe these precautions before every flight 1 Check to ensure that the Indicator LED 1s solid green not flashing 2 Check that positive collective increases blade pitch 3 Check that right aileron stick tilts the swash for a right roll 4 Check that nose up elevator stick tilts the swash for nose up 5 Always takeoff land and fly at a safe distance from yourself and bystanders 2011 Skookum Robotics Ltd 49 Intentionally Left Blank 2011 Skookum Robotics Ltd 50 15 Using the Self Leveling Bailout option WARNING Vibration levels must be low for this feature to work View several flight logs in the playback software before enabling self leveling to check that the red vibration error message does not appear If you use the SK720 s self leveling bailout option there are a few things to be aware of e Self leveling works better on helicopters with low vibration levels Tune your helicopter to eliminate high vibration and mount your SK720 as shown in Section 8 of this manual e Watch for vibration warnings where the LED is green but flickers red Self leveling will be automatically turned off whenever the SK720 displays this LED warnin
19. the trims and subtrims e The initial setup will be easier if you use a straight line pitch curve and no expo or dual rates in your radio These features can be set up later according to your usual preferences e Connect the SK720 to your PC using the included USB cable The SK720 setup software will automatically detect that the gyro is connected to your computer Check that the connection indicator in the upper left is green and says Connected e Good starting points for the cyclic and tail gains can be found in the Default Scale or Basic3D setups all of which are included with the PC setup software Look for these default setups under the SK720 setup software s File menu WARNING Do not use any of the Default Scale or Basic3D setup files mentioned above without first modifying them to suit your helicopter per Section 11 Steps 2 through 5 2011 Skookum Robotics Ltd 33 WARNING All the control input and sense directions set up in Steps 2 through 5 below must be correct or your helicopter will instantly crash if you try to fly it Follow these steps carefully and complete the pre flight check outlined in Section 13 of this manual before flying your helicopter Step 2 Match the Gyro to Your Transmitter e Click the Control tab in the Offline Setup Values area in the lower half of the setup software window see Figure 11 1 below Select the type of receiver that you will be usin
20. Flybarless System SK720 User Manual and Setup Guide The SK 720 replaces the tail gyro mechanical flybar and receiver on your R C Helicopter Other features include flight logging with playback optional self leveling and more to come This unit is ideal for pilots from beginner to 3D expert Go flybarless Rev 3 00 SK720 User Manual amp Setup Guide Table of Contents A HIVEFOCUCUION n aces econ teesseceatecsteicare araeched 3 2 IPaGKage C ONLCIUS oii cidicesciocsecccuiva verde a 4 DS Genmg Started ascosa toti ati eas cere sdi tensed tee sec oti otipuneresevites 5 A SACU e etadecs es si cwoser ae cnccuutusis tateveiuuverevener meamsavesneventaten 6 5 Modes LED Indicator and Power Up ccccseeseeeeees 7 6 Setup OvervieW siscictineniceceiectesteshitateeedlnanteni teat eee 9 7 Installing the Windows Setup Software and Utilities 11 8 Mounting the Gyro cccccceeeeeeeeeeeeeeeeeeseeneeseeeeseeneeseenenens 15 9 Helicopter Airframe Setup cccccssesseseeeeeeeeeeeeeneeenes 19 10 CONNECTIONS eecictesudconccouccieotuncinncdeubcecwateenneentiocustiodenceratteneciues 23 11 Gyro Setup Using the USB Interface 0 33 12 How to Check Cyclic Pitch amp Phasing seeee 45 13 After Setup Final Check ce eceeceeeeeeeeeeeeeeeeeeeeeees 48 14 Flight with the SK720 Gyro ccceeecceeseeeeeeeeeeeeeneeeeneeeeees 49 15 Using the Self Leveling Bailout op
21. PC setup software for the SK720 can be found on the unit s built in flash drive The SK720 will automatically be recognized as a new mass storage device when you connect it to your PC the files on it will be accessible a few seconds after you first plug it in to your computer Access files that are stored on the SK720 just like you would any other file on your computer Look for a file on the SK720 drive labeled SK720_ setup exe There is also a pdf copy of this user manual SK720 manual pdf and a configuration file SK720 CFG file stored on the SK720 The manual can be viewed with Adobe Reader and the configuration file should be ignored Install the setup software onto your computer by running the installation program SK720 Setup exe which can be found on the SK720 s built in flash drive e See Section 7 of this user s manual for detailed instructions on how to install the SK720 s Windows setup software e Use the PC based setup software s built in tutorial wizards to guide you through setting up your new SK720 on your helicopter e See Section 11 of this user s manual if you have questions about any of the tutorial wizard steps 2011 Skookum Robotics Ltd 5 4 Safety An R C helicopter is not a toy and can cause serious injury to people or damage to property Use of this gyro places a flight control computer the SK720 between the radio receiver and the servos that position the helicopter
22. Servos tab in the SK720 s setup software See Figure 17 1 below e Do the same for max negative pitch using servo travels for the other direction Offline Setup Vales ee r Swash Servo Options Serwo Trims and Reversing 7 IZ Trim ahaz Rev Servo Type Apal w Conter 00 E Servo Speed 014 seo Riam oo d F 3 Left Figure 17 1 Swash Servo Travel Adjustment Settings 2011 Skookum Robotics Ltd 57 4 Trim the swash for level hover On a day with light wind temporarily set the Hiller Decay to 200 and hover the helicopter hands off both nose out and nose in If it consistently drifts to its right left forward or back adjust the mechanical linkages to the swashplate to eliminate the drift Note that the swash will not be perfectly level as some sideways tilt is necessary to counteract the sideways thrust of the tail rotor 5 Adjust the Tail Drag Compensation on the Cyclic gain banks in the PC setup software There are fields for setting drag compensation in the elevator and aileron axes see Figure 17 2 below On a day with light wind start from a hover and then apply maximum positive collective If the helicopter s nose goes up lower the Tail Drag Comp number for Elevator by 1 or 2 steps If the nose goes down increase the Elevator value by 1 or 2 steps If the helicopter banked the right or left you may also have to adjust tail drag compensation for Aileron If it b
23. Servos tab is found in the Offline Setup Values region of the main SK720 setup software window as shown in Figure 19 5 below Offline Setup Values Swash Servo Options Servo Trims and Reversing Trim 2 servo Type 1 Center 126 0 2 1 125 0 s Servo Speed SIO 2 Right ea 3 3 Left as Beas aa Figure 19 5 SK720 Setup Software Swash Servos Tab Servo Type Digital uses higher frame rates than analog servos can handle which along with their better holding power improves performance Do not use digital frame rates for analog servos Servo Speed Take this value from your servo manufacturer s specifications Units are in seconds per 60 degrees of motion This helps the gyro move the swash evenly This field only matters if Equalize Servo Speeds is on Servo Travel Scales the amount of motion each servo has on either side of centre endpoints The servo travels can be set individually to trim the swash to be level at max zero and min collective pitch Servo Trims and Reversing Here each servo s center point can be set and each can be reversed if needed This is the same idea as sub trim on your transmitter Be careful that the servo doesn t bind 2011 Skookum Robotics Ltd 71 Tail Servo Tab The Tail Servo tab is found in the Offline Setup Values region of the main SK720 setup software window as shown in Figure 19 6 below Offline Setup Values Control Swashplate Swash Servos Tail Servo Cycl
24. Viewer can display accelerometer vibration frequencies in any of three axes lateral left right up down and fore aft It can also display the overall vibration The available options can be chosen from the Data Viewer s Show menu When data logging is set to Vibration mode vibration data is recorded by the SK720 in frames at approximately 1 second intervals throughout your flight You can select which data frame is displayed in the Data Viewer by using the slider at the bottom of the window Information about the vibration frequencies and time that the current data frame was recorded is displayed at the bottom of the window Hover your mouse cursor over any vibration peaks to see the corresponding frequency and RPM for that peak In the example below the highest peak occurs at approximately 16000 rpm This corresponds to the tail rotor frequency on the test helicopter and suggests that the tail rotor is the source of the highest vibrations Please see the Data Viewer s online help webpage available from the Help menu for more information about how to use this tool to tune your helicopter Skookum Robotics Data Viewer Fie view Show Register Help Lateral Acceleration Frequencies Overall Acceleration Frequencies Magnitude Currently viewing File LOGS SKY Current Data Frame Time 37 3 seconds Frequency at cursor 274 Hz 16440 RPM Figure 18 5 View a Vibration Log 2011 Skookum Robotics Ltd 64 19
25. and that the full range of tail blade pitch uses most of the servo s motion Faster stronger servos may help Tail doesn t hold very well in Set the tail Hold gain higher wind or backwards flight Helicopter slowly yaws in hover Make sure that auto trim at init is turned on and or increase the deadband value for rudder Piro starts stops in one direction Set the start stop acceleration values are good but the other direction for the tail to be lower for the direction bounces that bounces 2011 Skookum Robotics Ltd 83 Appendix A Specifications Gain channel inputs 2011 Skookum Robotics Ltd 84 Appendix B Firmware Upgrades 1 Make sure you have the most up to date version of the setup software installed You can find it on our website at www skookumrobotics com 2 Connect your unit to the setup software and save up your current setup file to your computer as a precaution 3 Disconnect any external power supply from the SK 720 4 Check that you have a good connection to the internet 5 Go to the menu bar in the setup software and select Utility gt Update SK 720 Firmware The setup software will then download the new firmware directly to your unit and begin updating it WARNING Do not disturb the SK720 while the firmware is updating The firmware update process may fail if you do thereby making the unit into a paperweight Your SK720 would then need to be returned to Skookum Robotics f
26. anked right decrease the value NOTE 1 Tail Drag Compensation is only a coarse setting it doe not need to be set precisely NOTE 2 The Tail Gain and Cyclic Gain values are overall gains The gain settings on the Tail and Cyclic tabs are multiplied by these overall values Offline Setup Values Control Swashplate Swash Servos Tail Servo Cyclic 1 Cyclic 2 Tali Tail 2 Base Gains and Rates General Elevator Aileron Control Rates 230 das C Lock Cyclic Gain to 50 g g pt Bell Gain 40 ol Self Tune Bell Gains Hiller Gain 50 50 3 Hiller Decay 75 il z Damping Gain 3 s l6 Self Levelling z Tail Drag Comp a ae Figure 17 2 Tail Drag Compensation setting 2011 Skookum Robotics Ltd 58 6 Adjust the collective torque compensation for the tail See Figure 17 3 below Start from a hover and then apply maximum positive collective If the tail goes right increase the collective to tail mixing for on the Tail tab by adjusting the Collec Mix field If it goes left decrease that value Offline Setup Values Bate Gains and Rates Misc Options Control Rate deg s L Lock Tail Gain to E Es Cantor Erpa C Small Heli Cyclic_k Collec Mix Rate Gain 0 Left Right Start Accel Hold Gain Accel Gain Figure 17 3 Collective Torque Compensation setting 7 Turn on the Self Tune Bell Gains option on one or both Cyclic tuning bank
27. as IO D7E IO C m 6 AXIS CONTROL IO A T K SW A SW L cue SKOOKUM D SWw C TAL J41 The SK720 is set to Spektrum JR Satellite Receiver mode by default at the factory You will have to set your SK720 for use with Futaba SBUS receivers Follow the directions in the PC Setup Software s Initial Setup Wizard or in Section 11 of this manual to set your SK720 for use with your Futaba SBUS receiver In Futaba SBUS receiver mode the SK720 outputs the throttle channel on port IO A T It also outputs up to four additional auxiliary outputs IO B IO C IO D and IO E for such things as a governor landing gear or light control The endpoints and trims of these auxiliary outputs must be adjusted in your transmitter NOTE For safety the throttle output is disabled while the SK720 is in setup mode Be sure to set the fail safe throttle level using the setup software See Section 11 Step 3 2011 Skookum Robotics Ltd 25 10 3 How to Connect PPM Receivers A PPM receiver can be connected to the SK720 by plugging it in to port IO B circled using a servo wire jumper cable Connect the other end of the servo wire jumper to the PPM output on your PPM receiver Be sure to set the SK720 for PPM receiver type before powering your receiver gt Sl Be IO D7E m o 65 AXIS CONTAOL IO ALT S K SW A Je SKOOKUM D Sw C f TAR JL The SK720 is set to Spektrum JR Satellite Receiver mode b
28. botics Ltd 37 e Goto the Swash Servos tab in the Offline Setup Values area in the lower half of the setup software window see Figure 11 6 below Select the servo type and speed according to the specifications of your servos Use the default servo speed if you don t know what setting to use for your servos Offline Setup Yalues a a Swash Servo Options Sewo Trims and Reversing ee Trim Mavens Rev ervo Type w a 3 Left 125 0 4 7 Figure 11 6 Offline Setup Values Swash Servos Tab e Make sure the control sticks are centered and then plug the servos into the gyro Check for good motion and no binding e Fit your servo arms so they are as close to 90 degrees to the linkage as can be achieved Next adjust the servo trims in the setup software until their arms are at exactly 90 degrees to their linkages and then use the linkages to level the swashplate NOTE Trims and sub trims on the transmitter should be set to neutral for best results Do not try to change cyclic throw or servo trims using your radio e Use the collective stick to check that all swashplate servos are correctly synchronized 1 e all swashplate servos move up and down together in response to collective stick motion If the swash plate servos are not correctly synchronized then you can reverse the individual servo directions by clicking on the associated Rev checkbox in the Servo Trims and Reversing area of the Swash Servos tab See Figure 11 6 ab
29. bs are found in the Offline Setup Values region of the main SK720 setup software window as shown in Figure 19 9 below The tab that is currently active is denoted by the blue bar Switch the active tab using your transmitter s gain bank channel Offline Setup Values rc Base Gains and Fates General Elevator Ail S S evalor neron C Lock Cyclic Gain to Gain Ch Also Scales a Damping Gains C Self Tune Bell Gains Control Rates 230 2F0 a degs 50 si iF a Bell Gain 40 Hiller Gain 50 4 ot Damping Gain 20 y Hiller Decay 75 Tail Drag Comp pi A self Levelling 0 a a x 47 mi m 15 4 a Figure 19 9 SK720 Setup Software Cyclic Tabs Control Rates The roll or pitch rate of the helicopter at maximum cyclic stick deflection This setting has a similar effect to changing the area of a flybar s paddles Bell Gain Amount of motion of the swashplate in response to cyclic stick deflection normally auto tuned by the SK720 To manually adjust the Bell gains While in a hover pitch the helicopter sharply nose down centre the cyclic stick and then do the same nose up If the helicopter is slow to respond turn the Bell gain up a small amount If the helicopter snaps back a bit and oscillates after it stops turn the Bell gain down a small amount Repeat until you get the best balance For sport flyers the Bell gain needs to be only roughly correct
30. c and 50 for the tail Note For very small helicopters start with 40 for the Cyclic gain and 30 for the tail gain Lift the helicopter off into a hover and try some small elevator and aileron motions If it oscillates or does anything violent as you spool up email Skookum Robotics technical support for help before flying again Incrementally adjust the tail gain to the maximum value possible without seeing any oscillation during hover or after sharp stick motions If the helicopter doesn t hold well in pitch or roll or slides to the side turn the Cyclic gain up a small amount If the helicopter oscillates while hovering turn the Cyclic gain down slightly Repeat until you get the best gain Try some forward flight If the helicopter oscillates in roll at high speed turn the Cyclic gain down a small amount If it doesn t hold well turn the Cyclic gain up Turn on the Self Tune Bell Gains option on one or both Cyclic tuning banks For each of those banks fly the helicopter as you normally would for at least four flights Use the SK720 setup software to disable self tuning once the gains stop changing significantly Self Tune Bell Gains is always turned on when using the setup software s Basic user interface Select the 3D Tuning or Advanced interface from the Preferences menu if you would like to turn off self tuning bell gains 2011 Skookum Robotics Ltd 55 7 After tuning your SK720 use the PC setup sof
31. ced Tail tab The Tail tab is found in the Offline Setup Values region of the main SK720 setup software window as shown in Figure 19 8 below Offline Setup Values Tail Gains and Rates Control Rates J degl Tail Expo F 25 oe zs C Lock Tail Gain to ao oe C Small Heli C Blur Piros Figure 19 8 SK720 Setup Software Tail Servo Tab Control Rate Sets the maximum allowable yaw rate of the helicopter at maximum rudder stick deflection One rotation per second is 360 degrees per second Tail Expo Positive values make the rudder stick less sensitive near center stick negative values make it more sensitive near center Lock Tail Gain This allows you to lock in a value for overall tail gain The SK720 will then ignore the end point setting in your transmitter and use the value you set here instead Small Heli This option increases the response delay that the system expects the tail servo to have Itis useful for helicopters 450 size and smaller Blur Piros Select this option to make your helicopter jump to a piro rate of 900 degrees per second very fast when you hold the rudder stick at full travel 100 2011 Skookum Robotics Ltd 74 19 1 Advanced Tuning Options The helicopter can be tuned in a more detailed way using the advanced user settings of the SK720 setup software To enable the advanced settings select the Advanced interface from the Preferences menu Cyclic Tuning Tabs The two Cyclic ta
32. cellaneous Outputs If it is difficult to see the SK720 s status LED when it is mounted on the helicopter an external LED can be used Just connect it to the port labelled EX LED like a normal servo cable For this port the top pin is for Green the middle pin is for Red and the bottom pin is Ground This option cannot be used in combination with a traditional radio receiver however There are also two additional ports on the side and back of the SK720 gyro One is for connecting the SK LCD interface and the other is for connecting an optional GPS or other future expansion accessories 2011 Skookum Robotics Ltd 32 11 Gyro Setup Using the USB Interface We suggest that you set up your helicopter the first time by following the step by step instructions in the Initial Configuration Wizard Swash Cyclic Setup Wizard and Tail Setup Wizard CAUTION Do not connect the swashplate or tail servos to the gyro until after the SK720 has been set up for your servos Your servos could be damaged by an incorrect configuration Step 1 Connecting e Start the SK720 setup software on your PC See Section 7 of this manual for instructions on how to install the setup software on your PC e Set your radio s transmitter so Aileron Elevator and Pitch Collective are output each on a separate channel Normal or 1 Servo swashplate mode on Spektrum JR transmitters or H 1 mode on Futaba transmitters Also centre all
33. ck centered after several receiver arent mounted near heat minutes of flight sources and let it acclimatize to field 2011 Skookum Robotics Ltd 81 2011 Skookum Robotics Ltd 82 Symptom Problem amp Solution Helicopter precesses in hover a Interaction between the Elevator motion like a child s spinning top Aileron and Yaw axes Check that the as it slows down Gets worse SK720 gyro is mounted correctly Also check rotor head phasing SK720 initializes properly but Electrostatic buildup on the tail belt there are violent twitches in drive Ground the tail boom to the hover in aileron elevator or frame and use a silicon based lube on the tail belt The vibration level of your heli may be tends to wander too high Improve the main and tail rotor s balance and or move the SK720 closer to the heli s C of G Check that the sense direction for the rudder yaw is correct and that the tail servo moves in the right direction Friction and or slop in the tail linkage gain is low Tail twitches a bit in hover Too much vibration is getting into the and or gain can t be set very unit Make sure its case isn t contacting high without wag the heli s frame and the wires leading to it are a bit loose For larger helicopters you may want to use a separate power bus to allow lighter wires leading to the unit Tail gain can t be set high Check if the tail boom is stiffly braced enough without oscillation wag
34. copter drifts slowly in Radio receiver centering drift Many elevator or aileron command and then release of the stick While in high speed forward flight Aileron damping gain is too low the heli sometimes oscillates in Warning too high damping gain is aileron hard on servos or Hiller is too high Helicopter hesitates in elevator Bell gain is too low relative to Control and aileron and continues to Rates Increase Bell gain slightly or Se temperature f hen th k Rates EEE E E en are Helicopter jumps in pitch or roll Check that the heli s centre of gravity After an elevator or aileron change Bell gain is too high relative to Control after hard enanges ORINEEN CG directly under the main shalt the rotor disk springs back after Rale positive and negative collective equalize swash servo throws and ihe stickis released check tail drag compensation Responds too sharply to aileron or Bell gain is too high During piros with collective pitch Servos are not fast enough or heli a changes or piros during forward needs to be better tuned for 3D See flight the helicopter wanders section 17 elevator or aileron with cyclic receivers center points drift with stick centered soon after take temperature up to 3 ticks of trim Use off transmitter trims to correct Helicopter drifts slowly in Gyro temperature changing too quickly elevator or aileron with cyclic or receiver drift Make sure the gyro and sti
35. ctions 10 1 through 10 4 for more on how to connect each type of receiver You will need to tell the SK720 which type of receiver you will be using See the PC Setup Software s Initial Setup Wizard or Section 11 of this manual for instructions on how to set your SK720 for use with your type of receiver 2011 Skookum Robotics Ltd 23 10 1 How to Connect Spektrum JR Satellite or Gaupner Receivers One or two Spektrum JR satellite receivers can be connected to the SK720 Two standard Spektrum JR satellite receiver plugs are located on the side of the SK720 at the location labelled SAT RX Either plug can be used if you are using only one satellite receiver gt El Ba SAT IO D7 E IO C an 6 AXIS CONTROL lIO ACT S K ee sen SW A SW L sun SKOOKUM E Sw C TAL n With the SK720 s power off connect your satellite receivers by plugging them in to the side of the unit The SK720 is set to Spektrum JR Satellite Receiver mode by default at the factory If you are using a Graupner satellite receiver you will have to set your SK720 for that type of receiver Follow the directions in the PC Setup Software s Initial Setup Wizard or in Section 11 of this manual to set your SK720 for use with your transmitter Connected Spektrum JR satellite receivers can be set to bind with a transmitter using the PC setup software Connect the SK720 to your computer using a USB cable and select Bind Sat RX s on Po
36. en the halves Also check that everything on your helicopter is secure and that the engine runs smoothly if it is nitro powered SK 720 Thin Tape Metal Plate P a Thick Anti Vib Tape Figure 8 2 SK720 Mounting Stack If you plan to use the SK720 s self levelling bailout feature it is better to mount the unit close to your helicopter s centre of gravity Also the lower the vibration levels on your helicopter the better self levelling bailout will work Subtle things like a canopy that rattles against hard mount points or a broken gear tooth can cause problems with self levelling and flight logs Note that some molded plastic main gears can cause large amounts of noise and vibration machined plastic gears may be better Note If you are getting frequent vibration warnings from your SK 720 it indicates that the vibration level is over 10 G s 2011 Skookum Robotics Ltd 17 Intentionally Left Blank 2011 Skookum Robotics Ltd 18 9 Helicopter Airframe Setup WARNING Good mechanical setup is critical to the gyro performing correctly Please read this section fully CAUTION The gyro should not be used together with a mechanical flybar as the results could be unpredictable It is intended for use where the swashplate alone drives blade pitch CAUTION Do not connect the swashplate or tail servos to the gyro until after the SK720 has been set up for your servos Your servos could be damaged by a
37. er due to interaction between pilot control and self leveling but if you center the sticks it will recover 2011 Skookum Robotics Ltd 51 The SK720 s self levelling feature is enabled by choosing a self levelling mode on the setup software s Cyclic tabs and then moving the adjacent slider to set the self levelling percentage see Figure 15 1 below This value sets how strongly the helicopter tends to pull itself towards level in elevator and aileron A higher self levelling percentage will make your helicopter return to level quicker when the controls are released Offline Setup Values a a Control Drive System Swashplate Swash Servos Tail Servo Cyclic 7 Cyclic 2 Tail 1 Tail 2 Cyclic Gains and Rates Control Rates J degl Hiller D ecap 75 Self Level Eaa sie v C Lock Cyclic Gain to Figure 15 1 SK720 Setup Software Cyclic Tabs Basic User Interface setting The Centre Stick self levelling mode illustrated in Figure 15 1 above is the recommended self levelling mode for new users of the SK720 The helicopter will fly normally with self levelling set this way but it will automatically return to level when the cyclic stick is released The Always On self levelling mode is the original SK720 self levelling mode The helicopter will always try to level itself in this mode making it feel like a coaxial helicopter This mode will also make some aerobatics impossible i e stunts involving inv
38. erted flight because the helicopter will fight the pilot s control inputs more strongly the further the helicopter is from level 2011 Skookum Robotics Ltd 2 In the CS Jnverted self levelling mode the helicopter will level itself to inverted if the cyclic is centred when the helicopter is within 60 of inverted Your helicopter will return to upright and level if the cyclic is centred while the helicopter is within 120 of right side up The On Inverted mode will level the helicopter to inverted when within 60 of upside down Unlike the CS Inverted mode the On Inverted mode will not switch off when you move the cyclic stick CAUTION Do not use inverted self levelling unless you already have some experience with inverted hovering Also The On Inverted mode will make your helicopter seem to stick upside down You will have to switch to another cyclic bank to recover 2011 Skookum Robotics Ltd 53 Using Self Levelling as a Bailout Mode If you want to use the SK720 s self levelling feature as a bail out mode choose the Centre Stick mode together with a high percentage of self levelling 1 e 80 The helicopter will fly normally with self leveling set this way but it will automatically return to level when the cyclic stick is released You can also use the A ways On self levelling mode for bail out To do this set up one Cyclic tab as your primary tab and set up the second cyclic tab as your bailout mode
39. es Control Hates J 240 degs Hiller Decay J 75 4 Self Levelling J 0 oe C Lock Cyclic Gain to 3 Figure 19 7 SK720 Setup Software Cyclic Tab Basic User Interface Control Rates The roll or pitch rate of the helicopter at maximum cyclic stick deflection This setting has a similar effect to changing the area of a flybar s paddles Hiller Decay A value of 100 here can help smooth out rapid tic tocks piros or other 3D manoeuvres especially repeated ones However high values for Hiller Decay will also limit the gyro s ability to hold steady in gusty wind or trim the helicopter precisely in hover A noticeable effect of higher Hiller Decay values is the need for more forward cyclic down elevator to keep the helicopter moving in forward flight Self Leveling Sets how strongly the helicopter tends to pull itself towards level in elevator and aileron Set the Self Leveling value to a higher value i e 80 in one of the two Cyclic tabs to enable a bail out switch Activate the bailout mode by switching to that bank Lock Cyclic Gain This allows you to lock in the value for overall cyclic gain The SK720 will then ignore the end point setting in your transmitter and use the value you set here instead 2011 Skookum Robotics Ltd 73 Tail Tab NOTE This section explains the Basic User Interface s Cyclic tab See the Advanced Tuning Options section Section 19 1 for details on the Advan
40. es to the fuselage pointing over the right 13 After Setup Final Check Soe OR ine e Opler gee igure 2 EIo Any time you change the gyro s setup always do these checks 1 Power up the helicopter with the servos connected and the swashplate mechanically set up Leave it undisturbed and wait for the LED to turn green 2 Input full right aileron on your transmitter Check that the swashplate tilts to the right 3 Input full up elevator nose up Check that the swashplate tilts back Blade Aligned 4 Input full right rudder on your transmitter Check that the tail pitch 90 to Boom changes for right yaw 5 Select throttle hold mode and then set zero collective pitch Check that the swashplate moves to give zero blade pitch 6 Set full up collective pitch Check that the swashplate moves to give maximum blade pitch 7 Pick up the helicopter wait a few seconds and then tilt it nose down and to the right The swashplate should tilt back and left 8 Rotate the heli s nose to the right 90 degrees The tail blades should Figure 12 3 Cyclic Elevator Pitch Phasing mor tocon ener rey em 8 Try full nose up elevator control with aileron control centered Measure the pitch of the blade that extends over the right side of the helicopter It WARNING Remember to return your throttle stick to the idle position should be about 10 degrees before releasing throttle hold 9 Try full left nose down elevator control with ailero
41. g e The maximum speed of recovery to level will only be as high as the maximum control rate for cyclic e The self leveling system is not an auto hover feature It doesn t know about wind or location so the helicopter will still drift if left on its own e The self leveling feature will work from any orientation including upside down The SK720 will not automatically adjust the collective however You will need to manually adjust the collective during a recovery and the helicopter may loose significant altitude in the process e Ifyou fly extended periods of 3D stunts the unit s sense of which way is up may not be perfect It may help to reduce the use of high collective pitch due to the high vibration it causes i e if you hear the blades barking Be prepared to switch back to normal mode after the helicopter has mostly recovered e Ifyou manually fly the helicopter in one of the two Always On self leveling modes it will feel like you are flying a coaxial helicopter You will have to continuously hold elevator and aileron controls to overcome the SK720 s desire to self level the helicopter Flipping the helicopter upside down may be difficult or impossible depending on how strong the self leveling setting is e Ifyou manually fly the helicopter in one of the two Always On self leveling modes avoid high yaw rates piros combined with large aileron or elevator control inputs Doing so may tumble the helicopt
42. g by choosing one of the options in the Type box Offline Setup Values a n Control Drive System Swashplate Swash Servos Tail Servo Cyclic 1 Cyclic 2 Tail 1 Tail 2 Radio nouei Stick Deadbands Gyro Mounting Orientation Type SpektrumJA Satellil Elevator Serwo Buti pomted Auleron 20 E Forward v Cyclic Gain Ch alzi L C Upside Down Tail Gain Ch Auto Trim at Init Kise _ Enable Logs Low Yoltage Alarm GEC wt 4 Figure 11 1 Selecting Receiver Type e Click the Send Setup button or press the F1 key to set the changes on the gyro You must SEND the setup whenever you want to test changes e The SK720 will automatically reset itself any time you change the receiver type and then press the send setup button e Try moving the elevator stick towards you nose up and look at the Elevator field under the Inputs From Receiver area circled in Figure 11 2 on the next page The number displayed should be close to 100 and should be shown on a green background when the transmitter s control stick reaches its stops If it is negative and displayed on a red background reverse that channel in your radio If it s too low or reaches 100 much before the stick s limit adjust the endpoints ATV s for that channel in your transmitter Typical end point ATV values will be near 125 for JR Spektrum radios 2011 Skookum Robotics Ltd 34 e Repeat for Aileron and Rudder inputs but
43. hapter 11 Step 4 in this manual Adjust swash servos for correct movement and trim them square See the Swash Cyclic Setup wizard in the Setup software or Chapter 11 Step 5 in this manual When the gyro is connected via the USB cable the LED light will slowly blink green See Chapter 5 for more information about the various LED States 2011 Skookum Robotics Ltd 9 8 Set up the tail servo with the help of the Tail Setup wizard in the setup software Alternatively see Step 6 in Chapter 11 of this manual 9 Set the Cyclic and Tail Gain Input Banks Reference Step 7 in Chapter 11 of this manual 10 Fly and trim Good starting points for the cyclic and tail gains can be found in the Default Scale or Basic 3D setups all of which are included with the PC Setup software Modify these default setups to suit your own helicopter See Section 11 for Basic Setup instructions 2011 Skookum Robotics Ltd 10 7 installing the Windows Setup Software and Utilities NOTE For clarity italics will be used throughout this manual whenever fields and regions of the setup software are referred to by name The PC setup software for the SK720 can be found on the unit s built in flash drive Connect your new SK720 to your PC using the included USB cable The SK720 will automatically be recognized as a new mass storage device Flash drive The files stored on it will be accessible a few seconds after you first plug
44. her mechanically or through the setup software It is important that the linkages and swash have minimal backlash looseness and the lowest friction possible The stiffness of the rubber rotorhead dampers also affects flybarless tuning and flight performance Performance will be better with the teeter damping stiffer than normal but excessive stiffness can cause vibration that is hard on the airframe gyros and Servos Tail It is important that you minimize tail rotor vibration Tail rotor vibrations affect the helicopter s elevator control because the axis of rotation of the tail rotor is aligned with the elevator axis Also if you have a belt driven tail be sure that your tail boom is electrically grounded to the helicopter s frame or motor case to prevent static electricity buildup Helicopter Centre of Gravity The gyro will perform best when the helicopter s centre of gravity CG is located directly under the main shaft or very slightly forward i e very slightly nose heavy This is especially important for maneuvers that use fast collective pitch changes combined with yaw 1 e piros 2011 Skookum Robotics Ltd 21 Intentionally Left Blank 2011 Skookum Robotics Ltd 22 10 Connections The SK720 can be connected to a traditional receiver or directly to modern satellite receivers such as Spektrum JR Graupner Futaba SBUS and PPM The available options can be selected from the PC setup software See Se
45. hined plastic gears may be better Note If you are getting frequent vibration warnings from your SK 720 it indicates that the vibration level is over 10 G s 8 2 Mounting the SK720 in Nitro and Large Electric Helicopters We strongly recommend that you use the Skookum Robotics SK PW7 power bus accessory on electric helicopters with main rotor diameters larger than 1100mm 43 inches and on nitro powered helicopters The High power servos typically used on larger helicopters draw a lot of current And while the SK720 s servo rail is rated for a total of 10 amps a set of four high powered servos will often be pulling 12 amps The SK PW7 Power Bus was designed for up to 20 Amps of continuous current It allows you to connect your high power 8 4 V servos directly to a 2S LiPo battery without having to draw large currents through your helicopter s other on board electronics Also six heavy servo cables will transfer a lot of vibration to the SK720 s acceleration sensors High vibration will degrade the quality of the self levelling and flight log playback 2011 Skookum Robotics Ltd 16 Mount the SK720 atop the metal damping plate that is included with the SK PW7 Power Bus Apply one vibration damping pad between the SK720 and the metal plate and a second pad between the metal plate and your helicopter see Figure 8 2 below For best results cut the pad in half and put one half at each end of the plate with about 7mm 1 4 betwe
46. ic 1 Cyclic 2 Tailll Tail2 Tail Servo Options Servo Trims and Reversing ByName Custom Trim Trave 1 Rev Servo Name MAE v Tail 0 0 3 125 0 8 125 0 6 Setup Servo with Rudder Stick L Stop Centre R Stop Figure 19 6 SK720 Setup Software Tail Servo Tab By Name Custom The tail servo type can be selected by either model number and manufacturer or if your servo type is not in the list by its specifications Freq Pulse If you have chosen to specify custom servo options then you can use this field to select the pulse type and update rate frequency Note that the wrong setting could cause the servo to bind and overheat This field will be greyed out if the By Name option is chosen Servo Travel Amount of servo motion on either side of centre endpoints Servo Trims and Reversing Sets the tail servo s centre point and direction Setup Servo with Rudder Stick This button starts a wizard that allows you to easily set up the tail servo s centre point and travel Just press the button and follow the prompts 2011 Skookum Robotics Ltd 72 Cyclic Tab NOTE This section explains the Basic User Interface s Cyclic tab See the Advanced Tuning Options section Section 19 1 for details on the Advanced Cyclic tab The Cyclic tab is found in the Offline Setup Values region of the main SK720 setup software window as shown in Figure 19 7 below Offline Setup Values Cyclic Gains and Rat
47. indicates that locked gains are being used see the Cyclic Gain field in Figure 11 2 on Page 31 l For users of JR Spektrum radios that have a gyro gain menu tail gains of 50 equal 0 100 equal 100 and 0 equal 100 Use values greater than 50 for one bank and less than 50 for the other Alternatively disable the gyro gain menu and set the gain channel end points per the method described above 2011 Skookum Robotics Ltd 42 If you only have one channel available for selecting between gain banks you can control one or both of the cyclic and tail gain functions with that channel In that case you should set the lock values per one of the options in Table 11 1 below Alternatively you can choose not to use two cyclic or two tail banks by selecting None in the Cyclic Gain Channel and or Tail Gain Channel fields see Figure 11 9 Choosing this option will result in the gains being locked on the associated tab See Section 16 of this user manual for detailed description of how to use the features in the Cyclic and Tail gain banks to tune your helicopter Step 7B Cyclic and Tail Gain Input Banks Traditional Receivers Cyclic Banks Locked Locked Not Locked Not Locked Only one gain channel is available when using a traditional radio receiver That single gain channel can be set to control both the cyclic and tail gain functions To avoid both the cyclic and tail banks having the same overall gain you can lock the
48. ion program The imported SK360 configuration can then be tweaked and loaded onto your new SK720 Replay Flight Log Select this item from the File menu to replay your flight logs in the 3D viewer See Section 16 of this manual for detailed description of how to use the 3D viewer 2011 Skookum Robotics Ltd 65 Items on the Utility menu include Bind Sat RX on Power Cycle use this option to bind any Spektrum JR satellite receivers that are connected to your SK720 Connect the SK720 to your computer using a USB cable and then select this option All connected satellite receivers will go into bind mode the next time that the SK720 is power cycled i e turned off and then on again Reset Log Counter When flight logging is enabled see the Control Tab section below selecting this option causes the log index number to be reset to zero Thereafter log file names will be LOGO BIN LOG1 BIN etc Reset Gyro Selecting this item on the Utility menu causes the gyro to reset immediately The unit will disconnect and then reconnect to Windows in the process Ensure that all open files on the SK720 flash drive are saved and closed before selecting this option This option is useful when binding satellite receivers because it allows the unit to be reset without having to disconnect it from your computer Format MicroSD Card This option will permanently erase the contents of your SK720 mass storage device Be sure to back up any im
49. l up unexpectedly if you set the throttle failsafe value to anything other than idle e Now make sure the helicopter s motor is off and then reconnect the SK720 to your PC On the Drive System tab see Figure 11 3 below click Set Throttle Failsafe and follow the instructions that appear Offline Setup Values a sz Control Drive System Swashplate Swash Servos Tail Servo Cyclic 1 Cyclic 2 Tail 1 Tail 2 Motor Engine lain Rotor Set Throttle Failsate Fi RPH Sensor 1 00 C Counter Clockwise Rotor Figure 11 3 Setting the Throttle Failsafe The throttle failsafe setting is the throttle position that the SK720 will send to your throttle servo or BEC when the SK720 looses radio reception or if the transmitter 1s accidentally turned off before the helicopter Step 4 Check the Gyro s Sense Directions e On the Control tab of the GUI select which way the SK720 s servo bus is pointed in your helicopter circled in Figure 11 4 on the next page Also select whether the gyro is mounted upside down label facing down or right side up label facing up e Now look at the Gyro Motion fields in the Live Data area shown in Figure 11 2 on the previous page Note that these fields sense movement not angles e Pick up the helicopter and slowly tilt 1t nose up The Gyro Rate for Elevator should be positive and show green e Repeat for the Aileron roll axis but slowly tilt the helicopter to the
50. levator Hiller gain in the setup For example if Elevator Hiller gain is 50 on a Cyclic gains tab the Cyclic Gain channel is set to 100 and Damping is set to 20 for elevator on the Cyclic gains tab then the resulting damping gain would be 100 50 20 40 This option can make it easier to re tune the gyro when mechanical changes are made that will affect the gains such as to cyclic pitch or head speed 2011 Skookum Robotics Ltd 76 Self Tune Bell Gains If enabled the SK720 will auto tune the Bell Gains in flight and save the new values in the setup a few seconds after it lands To lock in the values once auto tuning is complete disable this checkbox Note If you have auto bell tuning on and it sets the bell gain above 85 then the control rates are higher than your helicopter is capable of Hiller Decay Causes accumulated Hiller response to decay back to neutral to make the gyro more forgiving of perturbations If you watch a helicopter with a flybar in hover you ll see the flybar s disk offset for a moment then drift back to level after a sharp control input This option provides the same effect digitally A value of 100 here can help smooth out rapid tic tocks piros or other 3D maneuvers especially repeated ones However high values for Hiller Decay will also limit the gyro s ability to hold steady in gusty wind or trim the helicopter precisely in hover Self Leveling Sets how strongly the helicopter tend
51. move the sticks right green e Then check the collective pitch input moving the stick up green Reverse and or alter the end point values as necessary e Ifthe values in the Inputs From Receiver circled in Figure 11 2 below do not change as you move the sticks on your transmitter check to see if your receiver is bound e Spektrum JR Satellite receivers can be bound using the SK720 s bind mode Enable the bind mode from the Utility menu on the setup software by selecting Bind Sat RX s on Power Cycle Selecting this option will cause all connected Spektrum JR satellite receivers to enter bind mode the next time that the SK720 is power cycled 1 e turned off and then on again Live Data Yaw Sensor Gyro Motion Elevator 0 degs Alleron 0 degs 0 Rudder degs reen More bio Bank Aight Orientation Level Figure 11 2 Inputs From Receiver Step 3 Set up the Throttle Servo or ESC NOTE You should skip to step 4 if you are using a traditional receiver There is no throttle output from the SK720 when you use a traditional receiver e Disconnect the SK720 from the PC for safety the throttle output is disabled while connected to your PC e Connect your ESC or throttle servo to port IO A T on the SK720 then use the endpoints trims and reversing in your transmitter to setup the throttle servo to suit your helicopter 2011 Skookum Robotics Ltd 35 WARNING Your helicopter could spoo
52. n control centered ee The blade s pitch should be about 10 degrees NOTE In flight mode the swashplate will tilt slightly forward at full positive collective to compensate for tail drag Likewise it will tilt NOTE The SK720 s cyclic gains will need to be changed any time that slightly back at full negative collective the cyclic blade pitch range changes For example increasing cyclic pitch range by 10 is the same as increasing the stability gains by 10 2011 Skookum Robotics Ltd 47 2011 Skookum Robotics Ltd 48 14 Flight with the SK720 Gyro In flight mode the swashplate will not respond to the controls directly Its action will be similar to a heading hold tail gyro After it has been static for a few seconds it will level the swash during spool up to ensure a stable take off When you land your helicopter always wait at least 5 seconds after the rotor stops before spooling up again This enables the gyro to detect that the helicopter is spooling up Don t move the cyclic stick until the heli is light on its skids to prevent confusing the gyro before the helicopter can respond to the gyro s control inputs If the Auto trim at Init feature is on avoid using the transmitter trims for elevator aileron or rudder If you do use trims i e Auto trim at Init feature is off you ll have to zero them before every flight Note When you use the Self Tune Bell Gains option the SK720 has to be sure that the helicopter is on
53. n incorrect configuration See the nitial Setup Wizard in the PC Setup software or see Section 11 of this manual for information about how to set up the SK720 for your servos Main Rotor Blades Normal symmetrical rotor blades are recommended Flat bottomed rotor blades may be used but they have a nose down moment about their pitch axis and so require powerful swash plate servos The ideal rotor blades will be torsionally stiff but a bit flexible spanwise Rotor blades must also be balanced both spanwise and chordwise Heavier blades will make it easier to tune the helicopter Servos The best performance will be achieved if the servo s full normal range of movement is used You will need fast and ideally digital servos for good 3D performance Stronger faster servos will let you use higher damping gains see Section 17 which is important for maneuvers such as piro flips and tic tocks Be aware that the current draw on your cyclic servos will be higher than with a flybar Try to have 90 degree angles between the servo arms linkages swashplate and blade grip arms at zero degrees pitch mid stick to ensure even movement The gyro s USB setup interface will allow fine tuning of servo centers to achieve this 2011 Skookum Robotics Ltd 19 Swashplate Flybarless Rotorhead It is important that the linkages and swash have minimal backlash looseness and the lowest friction possible The stiffness of the r
54. n the Offline Setup Values area of the i Windows SK720 setup software Select By Name and find the model of tail servo on your heli in the Servo Name drop down list e Ifyou can t find your model of servo in the list then select Custom and look up the pulse type max frame rate and speed for your tail TOP VIEW TAIL For LEFT THRUST RUDDER the leading edges of the tail blades rotate and point to the RIGHT CA THRUST TOP VIEW For RIGHT RUDDER the leading edges of the tail blades rotate and point to the LEFT Figure 11 8 Check for Correct Tail Rotor Blade Movement If the tail blade pitch response is not correct reverse it by clicking on the Rev checkbox in the Servo Trims and Reversing area see Figure 11 7 Set the servo centering and endpoints by clicking Setup Servo with Rudder Stick and follow the instructions in the popup window servo Most servos will work at 333 Hz but the pulse type is NOTE The Tail servo will not move normally when the system is in important the Setup Servo With Rudder Stick mode It will only trim in the e Now connect the tail servo to the gyro First check that the direction of the servo is correct by moving the rudder stick on your radio as shown in Figure 11 8 on the next page direction of the transmitter stick position The tail linkage should be set up so that at center the servo arm is at 90 degrees to its pushrod and the tail blades ha
55. ng Alignment 8 1 Mounting the SK720 in Small Electric Helicopters Mounting tape with good damping must be used to isolate the SK720 from vibration Use the tape supplied with the SK720 to hold your SK720 in place in your helicopter 2011 Skookum Robotics Ltd 15 Be sure to clean the SK720 s base and the mounting site on the helicopter with isopropyl alcohol or another solvent before mounting the gyro A loose fitting padded safety strap may be used to ensure the gyro is secure in flight The gyro s case should not directly contact any hard surfaces on the helicopter s frame If a safety strap is used across the top of the gyro it should be padded slightly Cables connected to the gyro should be flexible and should have some slack near the unit 1 e do not strap the cables together or to the airframe within 5 cm of the SK720 Ideally use a cable sleeve because this maintains a neat appearance while allowing the cables to move relative to one another If you plan to use the SK720 s self levelling bailout feature it is better to mount the unit close to your helicopter s centre of gravity Also the lower the vibration levels on your helicopter the better self levelling bailout will work Subtle things like a canopy that rattles against hard mount points or a broken gear tooth can cause problems with self levelling and flight logs Note that some molded plastic main gears can cause large amounts of noise and vibration mac
56. o the gyro must be separate channels for elevator aileron and pitch collective control because the SK720 does its own swashplate mixing This gives the full precision of your radio set rather than losing half of its precision with in transmitter mixing It also allows for extra mixing features normally only available on high end radios such as Swash Ring and Servo Equalizing Elevator Cyclic Percentage of full swashplate motion at full stick deflection for elevator cyclic You can reverse the elevator servo using the Rev checkbox Aileron Cyclic Percentage of full swashplate motion at full stick deflection for aileron cyclic You can reverse the aileron servo using the Rev checkbox 2011 Skookum Robotics Ltd 70 Collective Pitch Percentage of full swashplate motion at full stick deflection for collective You can reverse the collective servo using the Rev checkbox Phase Trim Rotates the plane of cyclic action about the main shaft to allow correction for gyroscopic and aerodynamic effects It also allows the use of 3 or 4 blade rotor heads For example setting phase trim to 90 degrees would make full left aileron stick deflection tilt the swashplate fully forward Note that the phase angle will vary with rotor rpm and load so a happy medium value must be sought when setting this value See Section 12 of this user s manual for a step by step description of how to check the cyclic phasing Swash Servos Tab The Swash
57. o until after the SK720 has been set up for your servos Your servos could be damaged by an incorrect configuration See the nitial Setup Wizard in the PC Setup software or see Section 11 of this manual for information about how to set the SK720 for your servos NOTE The SK720 needs to receive separate aileron elevator and pitch inputs Set the swash type in your TRANSMITTER to 1 servo for all receiver types and swash setups Plug your swash and tail servos into the servo plug ports located on the front edge of the SK720 The ports are labeled TAIL SW C SW R SW L and SW A and are circled in the image below gt Et 1IO D E IO C o 5 AXIS CONTAOL lIO ACT Sw A K WE SKOOKUM PM SW R ROBOTICS SW C TAIL IL The tail servo should be plugged in to the TAIL port The swash servos should be connected per the following table and per the diagram on the next page Servo Output Layouts Servo SW C Servo SW C Servo Servo SW L SW R Servo SW L Servo SW R Servo SW A Additional servo outputs are available if you are using Spektrum JR Futaba SBUS or PPM satellite receivers The additional servo ports are circled in the image below These outputs are not available if you are using a stand alone traditional receiver 6 axIS CONTROL SKOOKUM A mi 1 pg ot 1 The electronic speed control ESC or throttle servo should be connected to IO A T Connect any auxiliary functions such
58. ollective command percentage is given as a guide for setting up your radio See Section 10 Step 3 for details about how this data is used to help setup your SK720 2011 Skookum Robotics Ltd 67 Control Tab The Control tab is found in the Offline Setup Values region of the main SK720 setup software window as shown in Figure 19 2 below Offline Setup Values Radio Input Options Stick QDeadbands Gyro Mounting Onentation Type Futaba 5 Bus wt Cyclic Gain Ch Tail Gain Ch Gear we Servo Bus is pointed Forward Ww C Upside Down ot ot ili J Auto Trim at Init Misc Enable Logs Low Voltage Alarm 25 LiPo Servo Battery Figure 19 2 SK720 Setup Software Control Tab Type When the Satellite Receivers option is selected in this field the SK720 will look for control inputs from the SAT RX ports and servo ports IO A to IO C will become outputs Otherwise ports IO A to IO E will be set to receive signals from a traditional radio receiver s outputs Auto Trim at Init With this feature enabled the gyro will use the aileron elevator and rudder stick centers it receives at initialization as neutral cyclic and rudder as applicable If disabled the gyro s inputs will need to be trimmed at the radio for each flight due to drift in the stick s sensors Stick Dead Bands To avoid drift due to small errors in stick centering a dead band can be set for the cyclic elevator and aileron function
59. or servicing 2011 Skookum Robotics Ltd 85 Appendix C Warranty and Technical Support Warranty and Repair Skookum Robotics Ltd warrants this product against any defects in materials or workmanship for a period of 90 days from the purchase date This warranty is limited to the original purchaser In the event of a malfunction Skookum Robotics will repair or replace the product to meet its standard operating condition This warranty does not apply in cases where the product has been overheated electrically shorted subject to crash damage otherwise abused or had unauthorized repair attempts UNDER NO CIRCUMSTANCES DOES SKOOKUM ROBOTICS ACCEPT LIABILITY FOR INCIDENTAL DAMAGE OR INJURIES RESULTING FROM THE OPERATION OF THE SK720 OR OTHER PRODUCTS Skookum Robotics will provide customers with technical assistance by email free of charge If a gyro s serviceability is in question following a crash we will check it over for only the cost of postage If the unit has malfunctioned and the 90 day warranty period has expired we will attempt repair and discuss the cost of possible repairs with the owner again for only the cost of postage If you wish to return the gyro unit or related product please write WARRANTY RETURN clearly on the shipping box and mail it to the address given below Manufactured in Canada by Skookum Robotics Ltd Email tech skookumrobotics com Website www skookumrobotics com Return Mail PO Bo
60. order to assist you in correcting those vibration problems High vibrations are identified with a yellow warning 2011 Skookum Robotics Ltd 62 message Extreme vibrations are identified with a red error message Extreme vibrations also result in the green with red flicker LED state on your SK720 See Section 5 of this manual for more information about indicators and errors on your SK720 You can use the Vibration Analyser to trouble shoot high vibration on your helicopter see below Data Viewer The Skookum Robotics Data Viewer was installed on your computer by default when you installed Version 2 51 or later of the SK720 setup software If you cannot find the Data Viewer on your computer download the latest version of the setup software from the Skookum Robotics website and install it Start the Skookum Robotics Data Viewer from the Windows Start menu and choose Open from the Data Viewer s File menu Vibration log files have a SKV extension as shown in Figure 18 4 below Skookum Robotics Data Viewer File Open Look ir My Recent Logs SKY Documents E Loe4 SEY f Logs sky kj Desktop User Files m File name w Network Places Files of type SK 720 Vibration Analysis Log File SEV Figure 18 4 Open a Vibration Log Alternatively you can open vibration logs from any Windows Explorer window by double clicking on the vibration log file name 2011 Skookum Robotics Ltd 63 The Data
61. ove e Check aileron and elevator swash motion for correct direction of travel If it isn t right you can reverse the elevator and aileron channels by clicking on the appropriate checkbox in the Swash Mixing area on the Swashplate tab See Figure 11 5 on the previous page 2011 Skookum Robotics Ltd 38 e Nowcheck the blade pitch range in response to full maximum and full minimum collective elevator and aileron Plus or minus 12 degrees of collective pitch and plus or minus 10 degrees of cyclic pitch are good starting points for most sport fliers These can be adjusted using the swash mixing values on the Swashplate tab See Figure 11 5 on the previous page Try to keep swash mixes to 60 or less This prevents unwanted interaction at max and min collective Increase the servo travels instead if you need more motion NOTE The Elevator Cyclic and Aileron Cyclic mixing change together in default setup software interface Select the 3D Tuning or Advanced interface from the Preferences menu if you want to adjust either value separately Step 6 Tail Setup Offline Setup Values as Control Drive System Swashplate Swash Servos Tail Servo Cyclic 1 Cyclic 2 Tail Tail 2 Tail Servo Options Servo Trims and Reversing By Name O Custom Trim Travel 4 Rev L Fi Setup Servo with Rudder Stick oor gt Centre L Stop R Stop Figure 11 7 Offline Setup Values Tail Servo Tab e Click the Tail Servo tab i
62. portant files such as the SK720 setup software directory before selecting this option Note that the format is done by the SK720 itself Use this option periodically to improve the speed of writes to the SK720 s flash drive The gyro will disconnect and then reconnect to Windows in the process and it may take 30 seconds or more to complete Update SK 720 Firmware SK720 program firmware updates will be provided from time to time by Skookum Robotics Select this option and follow the on screen instructions to update your SK720 with the latest software improvements Update SK LCD Firmware Choose this option to load the latest software revision firmware onto your SK LCD accessory The SK LCD must be connected to your SK720 before starting the update 2011 Skookum Robotics Ltd 66 Live Data Live Data Inputs from Receiver Yaw Sensor Gyro Motion Elevator Ee Elevator o deg Alleron Z Alleron o deg Rudder a Rudder o degs Collective freen Mose Lp Bank Bight eee a Orientation Tail Gain 400 4 Level Figure 19 1 SK720 Setup Software Live Data Region This area displays live telemetry from the gyro including your radio nputs from Receiver and Gyro Motion Remember that while in setup mode all elevator aileron and rudder stick motions are sent directly to the helicopter s servos to allow for easy mechanical setup See Figure 19 1 Under Inputs From Receiver the Pilot Elevator Aileron Rudder and C
63. re seven check boxes available and all but the SK720 Digital Flybar GUI checkbox can be selected on or off It is recommended that you install all of the available options unless you are sure that you won t need them Click the Next button to proceed to the screen shown in Figure 7 3 Select a directory in which you want to install the SK720 setup software use the default directory if you are unsure and then click Jnstall For reference only The latest version of Microsoft s NET runtime library must be installed on your computer for the SK720 configuration software to work Leaving the Check for Microsoft NET Runtime option enabled will allow the installation program to test whether you have the required runtime library installed on your computer If the required libraries are not already installed on your computer then the setup software will direct you to a Microsoft website where you can download the required files The OpenAL virtual audio driver is used by the 3D Flight Data Playback utility to generate sound effects It is not required if you have a Creative Labs sound card installed on your computer but we recommend that you install it anyway 2011 Skookum Robotics Ltd 12 25 SK7 20 Digital Flybar v3 00 Setup te YP ELF Choose Install Location ROBOTICS Choose the Folder in which to install SK720 Digital Flybar v3 00 Setup will install SK 20 Digital Flybar v3 00 in the Following Folder To install in a
64. s see Figure 17 2 For each of those banks fly the helicopter as you normally would for at least four flights Use the SK720 setup software to disable self tuning once the gains stop changing very much NOTE Changes to the self tuned bell gains are stored by the SK720 only after it has been standing still for at least 5 seconds Let your helicopter stand for at least 5 seconds after the rotor stops turning and the engine has been shut down to allow the SK720 to save any changes to its internal memory 2011 Skookum Robotics Ltd 59 18 Replaying Flight Recorder Data Logs The SK720 is unique among flybarless systems in its ability to log large amounts of data about your helicopter in flight That in flight data can be replayed in a 3D viewer or analyzed in a vibration analysis utility Data logs are created by the SK720 whenever logging is turned on in the setup software The two available log formats are Playback logs and Vibration logs Offline Setup Values a Control Drive System Swashplate Swash Servos Tail Servo Cyclic 1 Cyclic 2 Tail 1 Tail 2 Radio Input Options Stick Deadbands Gyro Mounting Orientation Type SpektrumJA Sats 1024 ee Gan ER Tail Gain Ch Servo Bus i pointed Forward wt Upside Down ARE Dio gf Figure 18 1 Enabling Logging in the SK720 Setup Software The 3D viewer mathematically reconstructs your flights from the data in Playback logs allowing you to improve yo
65. s as well as the tail rudder 1 to 2 percent is a good value for most radios note your radio s centering may change with temperature For scale models larger dead band can give a solid control feel while in stationary hover Note that all helicopters should have some dead band on rudder Mounting Orientation These settings can be changed to allow the gyro to be mounted in a variety of orientations in your helicopter See Section 11 Step 4 for details on how to use these options Low Voltage Alarm Use this box to set the low voltage alarm level Options are BEC or 2S LiPo servo battery Low voltage will trigger a Voltage error to be recorded and will cause the SK720 s LED to blink red 2011 Skookum Robotics Ltd 68 Drive System Tab The Drive System tab is found in the Offline Setup Values region of the main SK720 setup software window as shown in Figure 19 3 below Offline Setup Values Motor Engine Main Rotor Set Throttle Failsafe C RPH Sensor H C Counter Clockwise Rotor Figure 19 3 SK720 Setup Software Drive System Tab Set Throttle Failsafe After setting up your ESC or throttle servo use this button to tell the SK720 what your throttle channel idle setting is This sets the fail safe if you lose the radio link and helps improve auto rotations RPM Sensor Click this checkbox to tell your SK720 that an RPM sensor is connected to port IO C If selected the SK720 will record RPM data in the
66. s to pull itself towards level in elevator and aileron Set the Self Leveling value to a higher value i e 75 in one of the two Cyclic tabs to enable a bail out switch Activate the bailout mode by switching to that bank Intentionally Left Blank 2011 Skookum Robotics Ltd a 2011 Skookum Robotics Ltd Tail Tuning Tabs The two Tail tabs are found in the Offline Setup Values region of the main SK720 setup software window as shown in Figure 19 10 below The blue bar marks the tab that is currently active Switch the active tab using your transmitter Offline Setup Values Base Gains and Rates Misc Options Hea C Lock Tail Gain to 40 Control Expo 6 C Small Heli Cyclic Mix og C Blur Piros Collec Mix ag Rate Gain 75 Left Right Hold Gain 3 Start Accel Accel Gain Z Stop Accel Figure 19 10 SK720 Setup Software Tail Tabs Control Rate Sets the maximum allowable yaw rate of the helicopter at maximum rudder stick deflection Expo Positive values make the rudder stick less sensitive near center stick negative values make it more sensitive near center Rate Gain The response of the tail blades to the error in rate of motion This is the tail s primary gain Hold Gain The response of the tail blades to accumulated tail position error This allows the gyro to trim the tail and compensate for wind Set this value to 0 for rate mode Set this value to about 60 for heading hold Accel Gain Respon
67. se to acceleration error of the tail Gives a sharper response but is normally set low or to zero Sometimes helpful on smaller helis that feel loose near center This gain can be hard on the tail servo especially if there is a lot of vibration Small Heli This option increases the response delay that the system expects the tail servo to have It is useful for helicopters 450 size and smaller 2011 Skookum Robotics Ltd 79 Blur Piros This option makes it so a 100 input on the rudder stick will make the heli jump to a piro rate of 900 degrees per second very fast Start Accel The maximum rate of starting acceleration of the tail left or right If the value is too low the helicopter will seem sluggish in yaw If it s too high it will tend to bounce even at low gains Stop Accel The maximum rate of stopping acceleration of the tail Normally a little bit higher than the start acceleration Cyclic to Tail Feeds in tail pitch to directly compensate for torque changes due to changes in blade pitch due to cyclic aileron and elevator Normally 0 to 15 Increase this value if the helicopter s tail twitches to the right during flips Collec to Tail Feeds in tail pitch to directly compensate for torque changes due to changes in collective pitch Normally 15 to 30 Increase this value if the helicopter s tail twitches to the right during climb outs Tail Rate Mode and Heading Hold Set the hold gain to 0 for
68. specific type of error Error states are also recorded in the log file and will be displayed by the playback software Resetting the gyro will clear the error message 2011 Skookum Robotics Ltd 8 6 Setup Overview NOTE For clarity italics will be used throughout this manual whenever fields and regions of the setup software are referred to by name You will need to complete the following steps before you can fly your SK720 equipped helicopter 1 2 3 4 5 6 7 Connect the SK 720 to your computer using the included USB Cable and install the setup software See Chapter 7 for more details Start the setup software and familiarize yourself with the steps in the Initial Configuration Wizard tutorial The tutorial wizard will start the first time that you start the setup software Set your gyro for your servos with the help of the Initial Configuration Wizard Alternatively see Steps 2 and 3 in Chapter 11 of this manual Set up a new helicopter model on your transmitter Swash Type 1 servo Normal or H 1 depending on your radio Set all servos to normal direction i e not reversed Servo travel adjust 100 to start Travel adjust 100 to start Subtrims 0 Expo linear for now moo Mount the gyro in your helicopter See Chapters 8 through 10 in this manual Check for correct sensor readings with the help of the setup software s Initial Configuration Wizard Alternatively see C
69. tell which bank is active by looking at the position of the blue bar over the Cyclic and Tail tabs The blue bar will be located over the currently active tab In Figure 11 9 above the Cyclic 2 and Tail 2 tabs are the active tabs i e the settings on those tabs will be the active settings on the SK720 2011 Skookum Robotics Ltd 4 e You can see the effect of changes in your transmitter s endpoints on your gain settings by looking at the Cyclic Gain and Tail Gain fields in the Live Data area of the PC setup software see Figure 11 2 on Page 31 Set your tail and cyclic gains using your radio s endpoints 50 is a safe starting point for both the tail and cyclic gains Offline Setup Values es Cyclic Gains and Rates Control Rates J degl ge Hiller Decay J 75 oe Self Levelling Lock Cyclic Gain to Figure 11 10 Cyclic Tab Basic User Interface setting e You can also lock a gain to a fixed value by selecting Lock Cyclic Tail Gain to on the Cyclic Tail tabs The Cyclic tab 1s shown in Figure 11 10 above but the Tail gains can be locked on a Tail tab using an identical slider and check box Click the checkbox to enable the slider and then drag the slider with your mouse to set your locked gain values e Locking a gain will cause the SK720 to use the fixed value regardless of the gain channel s end point setting A small lock icon in the Cyclic Gain or Tail Gain fields in the live data area
70. the SK720 servo ports are connected to one another internally Only the signal pins i e the row of pins closest to the SK720 s label and one ground pin need to be connected to the receiver If you have purchased our SK CBL receiver cable kit hook up the Aileron and Elevator channels using normal male male jumpers Insert the single plug end of the cable tree sideways across the signal upper pins of IO C IO D and Ext LED The three plug end of the cable tree should be connected as shown in Figure 10 1 on the next page 2011 Skookum Robotics Ltd 27 TRADITIONAL RECEIVER THROTTLE ESC THROTTLE SERVO GAIN BANK SELECT COLLECTIVE SK CBL receiver cable kit RUDDER a ELEVATOR SK720 AILERON EX LED IO D E IO C IO B IO A T SW A SW L SW R SW C TAIL SWASH SERVOS TAIL SERVO Figure 10 1 How to Connect a Traditional Receiver to your SK720 Do you notice that that there is no throttle input to the SK720 from an external receiver The throttle signal from an external receiver must bypass the SK720 and be connected directly to the throttle servo or BEC Also it is not possible to use an external LED when using a traditional receiver If you are using the SK PWR bus along with your traditional receiver please see the separate SK PW7 Power Bus manual for details on how to connect it 2011 Skookum Robotics Ltd 28 10 5 How to Connect Your Servos CAUTION Do not connect the swashplate or tail servos to the gyr
71. tion 51 16 BaSiG TURING seciccsen scecesetdscenictssncenstessxivedsncieavidsneaseeratatcvwes 55 17 Advanced Tuning for 3D Pilots cccceseeeeeeeeeeeeeeeneees 57 18 Replaying Flight Recorder Data Log ccsceeeeees 60 19 Setup Software amp Advanced Features Guide 65 20 Trouble Shooting Guide cccecccseeeeseeeeeeeeeeeeeeneeeeeeees 81 Appendix A SpecificCations cccccceceeeseeeeseeeeeeneseeeseeeseeeees 84 Appendix B Firmware Upgrades c ccceeeeseseeeseeeeeeeeseeeees 85 Appendix C Warranty and Technical Support 86 2011 Skookum Robotics Ltd 1 Introduction The SK720 Digital Flybar is a high performance yet compact and lightweight pitch roll and yaw stabilizer for radio controlled R C helicopters It replaces the traditional flybar stabilizer bar mechanism and tail gyro while saving power increasing flight times and reducing repair costs Features include e Fybarless stabilization with piro compensation e Works as up to a 9 channel receiver core when used with Spektrum JR or Futaba SBUS satellite receivers e Supports radios with either 1024 or 2048 servo steps and 22ms or l Ims frame rates e Two dedicated Sat RX ports allow connection of up to 2 Spektrum JR satellite receivers Can also be used with PPM and traditional R C receivers Works with Digital or Analog swash servos Internal swash mixing
72. tware to save a copy of your setup to your computer s hard drive Save your setup using the Save Setup option in the File menu No further tuning should be required for most users If the maximum aileron and elevator motion of the helicopter is not fast enough for you however or for other advanced tuning see Sections 17 and 19 of this manual 2011 Skookum Robotics Ltd 56 17 Advanced Tuning for 3D Pilots Once you have flown a few flights and are familiar with using the setup software you can do some more advanced tuning to further improve your helicopter s performance during piros and fast collective changes 1 Ifyou haven t already done so change your setup software interface to Advanced or 3D Tuning Do this by selecting one of these two options from the Preferences menu 2 The helicopter s centre of gravity should be directly under the main shaft Check by putting the blades at right angles to the fuselage and pick the helicopter up with your fingers under the blade grips The helicopter should hang with the main shaft straight up and down 3 Ensure that the swash motion is even throughout its range e Put the SK720 into setup mode and set collective pitch to zero The swash should be level Adjust the individual servo centers or the linkages as required e Set the collective pitch to maximum positive The swash should still be level If not adjust the servo travels for one or two of the swash servos on the Swash
73. ubber rotorhead dampers also affects flybarless tuning and flight performance Performance will be better with the teeter damping stiffer than normal but excessive stiffness can cause vibration that is hard on the airframe gyros and Servos In general phase trim does not need to be set on rotor heads that were specifically designed for use with flybarless systems Modified Traditional Rotorhead When setting up a rotorhead mechanism originally designed for helicopters with a flybar removing the flybar while retaining normal servo arm length will likely give too much blade pitch action Either the servo travel or servo arm length will need to be reduced to allow normal gains and good performance See Section 12 of this manual for a detailed description of how to check for correct cyclic and collective pitch setup 2011 Skookum Robotics Ltd 20 Some kind of anti rotation or follower mechanism will also be needed to keep the top of the swashplate from rotating relative to the blade grips If the swashplate is not held so the linkage to the blade grips is at 90 degrees to the blades for 2 bladed rotors the phase angle will need to be adjusted See the diagram below Ball Link on Swash For initial flights the phase angle should be adjusted so that when the blades are lined up with the helicopter s tail boom they do not move with elevator input but do move with aileron input for 2 bladed rotors This can be set eit
74. uld not change pitch as you move the elevator control NOTE The aileron control not the elevator control changes the main rotor blade pitch when the main rotor is aligned as shown in Figure 12 1 above This is normal and is true for both flybarless and non flybarless helicopters 2011 Skookum Robotics Ltd 45 4 Ifthe main rotor blade pitch changed when you moved the elevator stick to full nose up at step 3 then you will need to adjust the phase angle You can do this either mechanically at the swashplate or using the Phase Trim option on the Swashplate tab see Figure 12 2 If the pitch became negative then adjust the phasing clockwise if it became positive then adjust it anti clockwise This will give you normal phasing 90 degree lead multi bladed rotors may fly better with some positive phase trim Offline Setup Values Pe a Suwash Type c Swash Mixing Mix Rev 120 Degree ellPM ela adie evator Cyclic 135 140 Degree eCCPM O mCP hd i Servo L F Aileron Cyclic O Collective Pitch 5 B go Degree eClPM 3 or 4 servo Options Phase Trim deg Swash Ring Piro Comp Figure 12 2 Swashplate Phase Trim 5 Try full right aileron control with elevator control centered The blade s pitch should be about 10 degrees 6 Try full left aileron control with elevator control centered The blade s pitch should be about 10 degrees 2011 Skookum Robotics Ltd 46 7 Next align a blade at 90 degre
75. ur maneuvers or just show your friends Flight logs for the 3D viewer are created by the SK720 when the Playback option is turned on in the setup software see Figure 18 1 above Starting at SK720 firmware version 2 00 playback logs have a SKL extension Earlier playback logs have a BIN extension The vibration analysis utility gives you a tool to detect sources of high vibration on your helicopter Flight logs for the vibration analyser are created by the SK720 when the Vibration option is turned on in the setup software Vibration logs have an SKV extension Note Vibration logs cannot be played back in the 3D viewer and Playback logs cannot be analysed in the vibration analyser 2011 Skookum Robotics Ltd 60 3D Viewer Start the 3D viewer by selecting Replay Flight Log in the File menu of the SK720 setup software You will be shown a dialog box similar to that shown in Figure 18 2 below Open a Gyro Flight Log file Look in EO Flight Logs iF m My Recent Documents Desktop User Files Local Terminal Network Places Files of type SK 720 Logs wv Cancel Figure 18 2 Replay a Flight Log Navigate to the directory where your flight logs are located and click the Open button We recommend that flight logs be copied off your gyro and onto your hard drive before replaying them The 3D viewer window will then open and begin playing back your flight Starting with Revision 2 00 of the setup software
76. ve 0 degrees of blade pitch 2011 Skookum Robotics Ltd 39 2011 Skookum Robotics Ltd 40 Step 7A Cyclic and Tail Gain Input Banks Satellite Receivers e Ifyou are using satellite receivers i e Specktrum JR Futaba SBUS or PPM you should have separate control over the Cyclic Gain and Tail Gain inputs By default the gear channel will control the overall cyclic gain and an Aux channel will control the overall tail gain This can be modified on the Control tab if needed see Figure 11 9 below Offline Setup Values a aiiin _ S Control Drive System Swashplate Swash Servos Tail Servo Cyclic 1 Ocli 2 Tail 1 Tail 2 Radio Input Options Stick Deadbands Gyro Mounting Orientation 5 pektu JA S atellil Cyclic Gain Ch Tail Gain Ch Misc _ Enable Logs Low Yoltage Alarm Servo Bus is pointed Forward w C Upside Down D ABE id Auto Trim at Init Figure 11 9 Selecting Which Channels Control Cyclic Tail Gains e The gain channel s endpoint setting in your transmitter will set the amount of gain for that function For example setting your gear channel s end points to 40 and 50 will give you 40 gain on one bank and 50 gain on the other This 1s illustrated below Bank 1 Bank 2 ules endpoint endpoint Gain Channel e The direction of a gain channel s output will set which cyclic or tail bank is active You can
77. wer Cycle from the Utility drop down menu All connected satellite receivers will then go into bind mode when the SK720 is unplugged from the USB and all other power sources and then plugged back in to a battery or BEC In Spektrum JR satellite receivers mode the SK720 outputs the throttle channel on port IO A T It also outputs up to four additional auxiliary outputs IO B IO C IO D and IO E for such things as a governor landing gear or light control The endpoints and trims of these auxiliary outputs must be adjusted in your transmitter NOTE For safety the throttle output is disabled while the SK720 is in setup mode Be sure to set the fail safe throttle level using the setup software See Section 11 Step 3 2011 Skookum Robotics Ltd 24 10 2 How to Connect Futaba SBUS Receivers CAUTION The SK SBI cable will power the SBUS receiver but it will not power any servos or other hardware connected to your SBUS receiver You could damage the SK720 and the SK SBI1 cable if you connect servos or other devices directly to your SBUS receiver as is The way around this is to remove the red wire from the SBUS end of the SK SB1 adapter A Futaba SBUS receiver can be connected to the SK720 by plugging it in to either of the two plugs located on the side of the SK720 at the location labelled SAT RX Use an SK SB1 dongle cable to connect the Futaba SBUS port on your receiver to the SK720 s SAT RX plug EX LED 7 evar mx B
78. x 46912 StnD Vancouver BC V6J 5M4 Canada 2011 Skookum Robotics Ltd 86
79. y default at the factory You will have to set your SK720 for use with PPM receivers Follow the directions in the PC Setup Software s Initial Setup Wizard or in Section 11 of this manual to set your SK720 for use with your PPM receiver In PPM receiver mode the SK720 outputs the throttle channel on port IO A T It also outputs up to three additional auxiliary outputs IO C IO D and IO E for such things as a governor landing gear or light control The endpoints and trims of these auxiliary outputs must be adjusted in your transmitter NOTE For safety the throttle output is disabled while the SK720 is in setup mode Be sure to set the fail safe throttle level using the setup software See Section 11 Step 3 2011 Skookum Robotics Ltd 26 10 4 How to Connect Traditional Receivers It is important to turn the SK720 s satellite receiver option off using the PC setup software before connecting a traditional stand alone receiver Follow the directions in the PC Setup Software s Initial Setup Wizard or in Section 11 of this manual to set your SK720 for use with a traditional receiver Connect your traditional receiver to the SK720 using four servo jumper wires or using a SK CBL receiver cable kit The SK CBL receiver cable kit and or servo jumper wires must be purchased separately The connector mapping is Receiver Channel SK720 Port Collective Pitch 0D Gain Bank Select EXT LED All power and ground pins on

Download Pdf Manuals

Related Search

Related Contents

Robot-boulanger All-In-One DeluxeMC  Belkin Screen Guard Anti-Glare Overlay  Istruzioni d`uso e di montaggio Cappa aspirante  854 Quad Bender  Instandhaltungsanleitung Manuel d`entretien Istruzioni per la  CableMaster 450  Manual de instalación Gateway Wireless  Bravo 180s Crop Sprayer  GH3000 User manual original_DE  March 2014  

Copyright © All rights reserved. Failed to retrieve file