Quick Start Guide
Contents
1. Apply to save settings 4 8 16 CH NVR Quick Start Guide Step 3 Enter into MenuIP Cameras tab as shown below Click Search button to search the devices in the same local area network DEVICE MANAGEMENT oH Device NetAddress Manufacturer Product Model Status Click Refresh button to refresh the searched devices You can modify the IP address of the searched device by checking the device and clicking Setup button Note If the network of IP cameras and NVR are in LAN their IP address must be in the same network segment For example If the IP address of NVR is 192 168 013 057 the IP address of IP camera must be 192 168 013 XXX ADD DEVICE Manufacturer Product Mod IP Address 1 1 1 1 172 1 1 1 1 1 Check the device you want to add and then click OK button to return to the previous tab The added devices will be listed Step 4 Select the device and click Setup button to bring up the following window Enable Channel Manufacturer Product Model IP Address Server Port User Name Password Step 5 Check Enable checkbox select channel and input the username and password of the device see the User Manual of IP Camera for details Then click OK button to return to the previous tab Step 6 Click Apply button to save settings Then exit the configuration tab This will take you to see the live images 4 8 16 CH NVR Quick Start Guide 7 2 On WAN2. 1 Connect the NVR to internet through router or virtual server e Enter into Menu gt Information gt Network tab to check the network settings of the NVR e Forward IP address and port number in Virtual Server setup of the router or virtual server Configure the firewall to allow accessing the NVR e Open IE browser input IP address or dynamic domain name and enter If HTTP port is not 80 add the port number after IP address e JE will download ActiveX automatically Then a window pops up and asks for user name and password Input name and password correctly and enter to view 2 Connect the NVR to Internet through PPPoE e Enter into the NVR s Menu gt Setup gt Network interface to enable PPPoE and then input user name and password received from your ISP Next click Apply The NVR will connect to the server and would give a confirmation message e If users want to utilize dynamic domain name please apply for a domain name in a DNS server supported by the NVR or router Then add to the NVR or router e When accessing the remote interface of NVR you can input WAN IP domain name to access directly user can enter into Main menu Information Network interface to check IP address If HTTP port is not 80 add the port number after IP address The browser will download Active X control e The following steps are the same as the connection way above 450041000416 Al
3. 3 1 Startup Step 1 Connect to monitor Step 2 Connect with the source power Step 3 The device will boot and the power indicator will display blue Step 4 A WIZZARD window will pop up 3 2 Shutdown You can shut down the device by using IR remote controller and mouse By IR remote controller Step 1 Press Power button This will take you to see a shutdown window The unit will shut down by clicking OK button Step 2 Disconnect the power By mouse Step 1 Enter into Menu and then select Shut Down icon This will bring up a shutdown dialog box 4 8 16 CH NVR Quick Start Guide Step 2 Click OK Then the unit will power off after a while Step 3 Disconnect the power 4 Setup Wizard After the device starts a setup wizard pops up You can set up time network and disk management WIZARD Device Name Language English Date Format MM DD Y Time Format Time Zone MT System Date 03 24 7 2012 FW System Time gt 40 49 Startup Wizard Next ES Click device name box to pop up a keyboard as follows It supports digits alphabets and symbols as inputs Click Shift button to input capital letters and symbols click Shift button again to return Click Next button to bring up a network setup window WIZARD HTTP Port Server Port Obtain an IP address automatically V IP Address 192 168 011 061 Subnet Mask 000 000 000 000 Gateway 192 168 011 001 Preferre
4. in 4 8 16 CH NVR Quick Start Guide the start time field Step 4 Select the channel display mode and click gt button to play record Use the playback toolbar to control the playback SEARCH vent Search File Management Image Start Time 21 f 2013 25 EA 00 OO 8 00 6 01 12 00 9 3 Playback by Event Search Step 1 Enter into Menu gt Search gt Event Search tab SEARCH Start Time 03 04 2013 03 04 2013 03 04 2013 03 04 2013 Step 2 Select date and channels on the right hand side A data with highlighted borderline indicates presence of data Step 3 Then checkmark Motion Sensor or All accordingly You can search for motion based recording and sensor based recording Step 4 Press Search button to display the searched event information in the event list box Step 5 Double click the event item to play the record 9 4 Playback by Image Search Step 1 Enter into Menu gt Search gt Image tab 4 8 16 CH NVR Quick Start Guide SEARCH lime Search Event Search File Management f 5 wh ver va es y aA gt Step 2 Select data and channels on the right hand side Step 3 Press Search button to search for a recorded image Step 4 Once an alarm image has been identified the user can double click the image to play the recording You can lock the image by clicking Lock button Click Save button to copy the image on the HDD Click Save All to copy all imag
5. of the two schedules must match otherwise you cannot get the record in some time 8 4 Sensor Based Recording To Set Sensor Based Recording Step 1 Enter into Menu gt Setup gt Schedule gt Sensor tab The setup steps for schedule for sensor based recording are similar to normal schedule setup You can refer to 8 2 Schedule Recording for details Step 2 Enter into Menu gt Setup gt Alarm Sensor gt Sensor tab as shown below Step 3 Enable sensor alarm Please specify to channel select senor type and click Apply to save settings 4 8 16 CH NVR Quick Start Guide Default Exit Step 4 Enter into Menu gt Setup gt Alarm gt Sensor gt Schedule tab to bring up schedule settings for sensor alarm The setup steps are similar to normal schedule setup You can refer to 8 2 Schedule Recording for details Note The timelines of the two schedules must match otherwise you cannot get the record in some time 9 Playback This unit supports four kinds of playback 9 1 Live Playback Click Playback button on the main menu bar to playback the record You can do relevant operation by clicking the buttons on screen 9 2 Playback by Time Search Step 1 Enter into Menu gt Search gt Time Search tab Step 2 Select date and channels on the right hand side and press Search button A date with highlighted borderline indicates presence of data Step 3 Set the start time by clicking a particular grid or by entering the specific value
6. 1 Enter into Menu gt Setup gt Schedule gt Motion tab The setup steps for schedule for motion based recording are similar to normal schedule setup You can refer to 8 2 Schedule Recording for details Step 2 Enter into Menu gt Setup gt Alarm Motion Motion tab as shown below 4 8 16 CH NVR Quick Start Guide MOTION Holding Time S Trigger 10 Setting 10 Setting 10 Setting 10 Setting Step 3 Enable motion alarm Please specify to channel and click Apply to save settings Step 4 Click Setting button under the Area to set Sensitivity and Detection area Left click the grid and drag to delete the area Drag again to add area You can drag slide bar to set the sensitivity value 1 8 The higher the value is the more sensitive it is to motion Since the sensitivity is influenced by color and time day or night you can adjust its value according to the practical conditions Click EJ icon to set the whole area as detection area Click icon to clear the set detection area Click S icon to test the sensitivity as per the local conditions Once motion is sensed it displays a figure icon Click icon to save the setting Click icon to exit the current interface as oa Se a Step 5 Enter into Menu gt Setup gt Alarm gt Motion gt Schedule tab to bring up schedule settings for motion alarm The setup steps are similar to normal schedule setup You can refer to 8 2 Schedule Recording for details Note The timelines
7. Quick Start Guide 4 3 16 CH NVR 4 8 16 CH NVR Quick Start Guide 1 Install Hard Drive Notice 1 Support one SATA hard drive Please use the hard drive the manufacturers recommend specially for security and safe field 2 Please disconnect the power before being connected to other devices Don t hot plug in out Step 1 Loosen the screws to open the top cover and then connect the power and data cables After that place the HDD onto the bottom case as Fig 1 1 Step 2 Secure the HDD with the screws as Fig 1 2 Fig 1 1 Connect HDD Fig 1 2 Screw HDD Notice 1 For the convenience to install please connect the power and data cables firstly and then tighten it with the screws 2 Rear Panel Instruction 1 2 3 4 5 6 7 8 9 10 11 12 Rear Panel for 4 ch 1 2 3 45 6 7 8 9 10 11 12 Rear Panel for 8 ch 4 8 16 CH NVR Quick Start Guide AUDIO AUDIO CVBS Tum mi LAN USB 9 E a x 654321 i HDMI 1 2 3 4 5 6 7 8 Rear Panel for 16 ch tem Name eseriptiom O O O a auction icHaudioinp OOOO 3 Aamin Alarm Inputs for connecting sensors ee a a e Grounding Relay Output Connect to external alarm 6 cvs VGA port VGA output connect to monitor o HDMI port Connect to high definition display device Network port e USB port Connect to external USB devices like USB flash USB mouse etc 11 DC12V Power input RS485 Connect to keyboard A is TX B is TX 3 Startup amp Shutdown
8. Step 1 Set up the network of NVR Enter into Menu gt Setup gt Network tab as shown below Input IP address Subnet Mask etc or enable PPPoE and then input user name and password received from your ISP 192 168 011 061 000 000 000 000 192 168 011 001 Preferred DNS Server 192 168 011 001 Alternate DNS Server 1000 000 000 000 PPPol Password est Default Apply Step 2 Click Test button to test the effectiveness of the network After that click Apply to save settings Step 3 Enter into Menu gt IP Cameras tab Click Add button to add IP cameras ADD DEVICE Enable Channel Manufacturer Product Model IP Address Server Port Step 4 Check Enable checkbox select channel manufacturer product model and input IP address server port username and password of the device see the User Manual of IP Camera for details Then click OK button to return to the previous tab Here the IP address of the camera must be a WAN IP address If it is a LAN IP address please forward the IP address and server port in the virtual server setup of the IP cameras router or virtual server and then find its WAN IP address to fill in here Note IP address and port forwarding settings may be different in different routers Please refer to the router s manual for details Step 5 Click Apply button to save settings Then exit the configuration tab This will take you to see the live imag
9. d DNS Server 192 168 011 001 Alternate DNS Server 000 000 000 000 Next f Exit The default HTTP port is 80 The default server port is 6036 You can check Obtain an IP address automatically to acquire network information or input IP address subnet mask gateway preferred alternate DNS server manually This function is used to monitor NVR through internet See Section 7 for details Click Next button This will take you to the HDD management window 4 8 16 CH NVR Quick Start Guide WIZARD You can check your HDD information through this tab If your HDD was recently installed select the HDD from the list to format it Click Next button This will let you see your NVR status And then click Finish button to end this wizard You can also refer to the complete setup steps from the relevant sections of NVR User Manual If you don t want to set up Wizard please click Exit button to exit 5 Login After you exit the wizard setup you can login to the NVR Notice Hold and press ESC key to switch the output among BNC VGA and HDMI Press the MENU button to bring the LOGIN dialogue box and then enter the user name admin and password 123456 User Name admin Password 6 Main Menu Setup Click right mouse or press ENTER button on the front panel to enter into the main menu Then click Setup to go into Setup interface as shown below 4 8 16 CH NVR Quick Start Guide Basic config
10. es 8 Recording Setup A user needs to install and format a HDD and set all the recording parameters before recording There are four kinds of record modes 8 1 Manual Recording A user can press REC button on the front panel after quitting system setup Press this 4 8 16 CH NVR Quick Start Guide button again to stop recording Or press REC button on remote controller Click it again to stop Or click REC button on the tool bar with mouse Click it again to stop 8 2 Schedule Recording To Set Schedule Recording Step 1 Enter into Menu gt Setup gt Schedule tab Refer to the following picture SCHEDULE Step 2 Click Ea button to add a certain day schedule click ki button to delete the selected schedule Step 3 You can also double click the grid to pop up a week schedule window SCHEDULE ek Days Wednesda Apply Settings To A End Time Select day and then click Add button to set up the start time and end time Then select other days and click Copy button to save the setting to other days Finally click OK button to save week schedule Step 4 Select other channels and set timeline for them or select Apply Settings To All Channel and click Copy button to set the same settings for all channels 8 3 Motion Based Recording Motion detection based recording when there is a motion event detected the camera will be triggered to record To Set Motion Based Recording Step
11. es on the HDD Note In order to take images on alarm the snapshot feature should be activated in Alarm Handling for different kind of alarms 10 Back up This unit supports backup by USB flash Step 1 Enter into Menu Backup tab BACKUP Step 2 Set the start amp end time select channels and click Search button to display the searched data in the data backup list box Step 3 Select a required file or checkmark All to select all data files Click Backup button to pop up Backup information window Step 4 In the backup information interface user can check the relevant options for backing up files These options include storage Media backup player and save file type 4 8 16 CH NVR Quick Start Guide Then click Start button to start backup 11 Remote Surveillance In order to view the NVR from a network it must be connected to a LAN WAN or internet The network setup should be done accordingly 11 1 Access NVR on LAN e Enter into Menu gt Information gt Network tab to check the network settings of the NVR e Enter into Record Setup to set network video parameters like resolution frame rate etc e Open IE on a computer on the same network segment Input the IP address of the NVR in IE address bar and press enter If HTTP port is not 80 add the port number after IP address e JE will download ActiveX component automatically Enter the username and password in the subsequent window 11 2 Access NVR on WAN
12. uration Set video system menu language audio time and authorization check Live configuration Set name time display picture color and hide cameras Record configuration Set record quality frame rate resolution time stamp and recycle Schedule configuration Set schedule for timer motion detection and sensor alarm respectively Alarm configuration Set sensor type alarm trigger and buzzer alarm Network configuration Enable network function and configure IP address DDNS transmission video parameters here User configuration Administrator can add delete users and change their authorization Advanced configuration Reboot the device and import amp export data into or from mobile storage medium 7 Network Configuration In order to preview the live images you must set up the network of NVR first and then add IP cameras The NVR should be connected to a LAN WAN or Internet 7 1 On LAN Step 1 Set up the network of NVR Enter into Menu gt Setup gt Network tab as shown below Input HTTP Port the default value is 80 Server port the default value is 6036 IP address Subnet Gateway If using DHCP please enable DHCP in both the NVR and the router NETWORK Network Email Server Other Setting HTTP Port Obtain an IP address automatically IP Address Subnet Mask Gateway Preferred DNS Server Alternate DNS Server Step 2 Click Test button to test the effectiveness of the network After that click
Download Pdf Manuals
Related Search