Winchester Model 1300 Owner`s Manual
Contents
1. 3 To operate your Model 1300 in a single shot mode a shell can now be placed directly into the chamber through the ejection port IMPORTANT WHEN THE SLIDE IS MOVED FORWARD WITH A SHELL PLACED DIRECTLY INTO THE CHAMBER THE GUN IS NOW READY TO FIRE LOADING THE MAGAZINE Before loading make sure your shotgun is pointed in a safe direction you are in an appropriate location for loading and that shooting will be imminent 1 Place the safety in the on safe position and close the action 2 Depress the carrier with the front of the shell Figure 6 3 With your thumb on the base of the shell push the shell into the magazine until the carrier returns to the original position 4 Repeat the procedure until the magazine is fully loaded WARNING TO AVOID ACCIDENTAL DISCHARGE DO NOT CARRY A GUN WITH A SHELL IN THE CHAMBER 11 Loading the magazine UNLOADING PROCEDURES Perform the following steps to remove shells from the chamber and magazine on all Model 1300s 1 Point the muzzle in a safe direction 2 The safety should be in the on safe position the red warning band will not be visible 3 Hold the disconnector release button inward to release the slide Figure 5 Slide the forearm through a complete cycle of the action and repeat the process until all the shells in the magazine have been transferred to the chamber and then ejected D 5 When the last shell in the magazine h2. 3 Unscrew and remove the magazine cap Remember always keep the end of the magazine pointed in a safe direction 4 Slide the barrel forward withdrawing the barrel from the receiver and disengaging the barrel bracket from the front end of the magazine 5 Immediately screw the magazine cap back onto the magazine REMOVAL OF THE TRIGGER GUARD GROUP FROM THE RECEIVER Removing the trigger guard group is another necessary procedure in performing thorough maintenance of your 21 shotgun It is easy to do and removing it allows you to perform cleaning and maintenance whenever and wherever required With both the trigger guard group and bolt assembly removed it is easy to wipe out any debris or moisture that sometimes accumulates in the receiver The trigger guard group should be removed before you attempt to remove the bolt assembly iF Make sure the gun is completely unloaded as explained previously in this owner s manual Cycle the action by sliding the forearm rearward and then forward This puts the hammer in the cocked position Place the safety in the on safe position If the barrel assembly has been removed always be sure to replace the magazine cap on the end of the magazine tube to prevent accidental disengagement of the magazine spring retainer Place your gun with the trigger guard facing up on a suitable surface that will protect the receiver finish and stock Remove the tr
3. RIFLES AND SHOTGUNS Winchester Model 1300 Owner s Manual Important instructions for Winchester Model 1300 Shotguns Customer Service Department United States Winchester Firearms 275 Winchester Avenue Morgan Utah 84050 9333 Phone 1 800 945 5237 If you have any questions or comments regarding your new firearm please feel free to write or call us Use the space below to record information about your new firearm Model Serial Number Purchased From Date of Purchase Winchester trademarks licensed from Olin Corporation A00504 04441 Contents Page Gun Safety Warninss Asus ausleihen 1 General Description sans sen 2 General Operation 04 200 3 Terminology and Descriptions ss u 1 20 3 Serial N mber sus arena 4 PRR Ot yen ces aia bh ad athe oh ent anh Ap ee 4 Magazine Capacity 2 45 ehesten 5 Initial Cleaning Olin lt cncdentadeesSeesteaper tars 5 Operation of the Safety s4 2 66a rc eosrvsave weak eas 8 Initial Assembly Takedown 0 000 ce eee 9 Loading Procedures erst as and dss bind ase ew 10 Unloading Procedures 22 0 0200 20 2 11 Firine Proeedures un 22 0400 same wae kOe eM aoe 12 In the Case of a Misfire sis2352 3 ee 13 WinChoke Choke Tube System 05 13 Removing the Magazine Plug 0 000 16 Sioht Adjustments a sense nel 17 Complete Disassembly 0 000 e eee 20 Cleaning and Maintenance Suggestions 25 Parts Service Repair and Que
4. sunscreens etc Damage to camouflage Dura Touch and other finishes caused by chemicals is irreversible and unrepairable If your new Model 1300 is to be stored for an extended period of time it is permissible to leave the rust preventative compound in place and keep your Model 1300 in its box for maximum protection during long term storage OPERATION OF THE SAFETY Your new Model 1300 Winchester shotgun is designed with a cross bolt type safety It is located just forward of the trigger on the trigger guard and is convenient for gloved or ungloved fingers Figure 4 It is essential that you become very familiar with the feel look and operation of the safety on this shotgun before attempting to load and shoot With the safety in the on safe position the trigger and hammer are blocked and the shotgun cannot be fired In the off safe position if your gun is loaded with a round in the chamber the chambered round can be fired by simply pulling the trigger e ON SAFE The safety button is pushed fully to the right The red band on the left side is not showing Always maintain the safety in the on safe position fully on when a cartridge is in the chamber and until shooting is imminent FIGURE 4 Off safe position red band showing e OFF SAFE The safety button is pushed fully to the left Figure 4 A large red band is exposed on the button as it protrudes on the left side of
5. FIREARMS U S REPEATING ARMS CO CAN ASSUME NO RESPONSIBILITY FOR INCIDENTS WHICH OCCUR THROUGH USE OF CARTRIDGES OF NONSTANDARD DIMENSION OR THOSE DEVELOPING PRESSURES IN EXCESS OF SAAMI SPORTING ARMS AND AMMUNITION MANUFACTURERS INSTITUTE ESTABLISHED STANDARDS DISCHARGING FIREARMS IN POORLY VENTILATED AREAS CLEANING FIREARMS OR HANDLING AMMUNITION MAY RESULT IN EXPOSURE TO LEAD AND OTHER SUBSTANCES KNOWN TO CAUSE BIRTH DEFECTS REPRODUCTIVE HARM AND OTHER SERIOUS PHYSICAL INJURY HAVE ADEQUATE VENTILATION AT ALL TIMES WASH HANDS THOROUGHLY AFTER EXPOSURE Incorrectly reloaded ammunition can cause serious personal injury and damage to the firearm due to excessive pressure Reload only after proper instruction and in strict compliance with instructions and data contained in current reloading manuals MAGAZINE CAPACITY It is extremely important that you know the magazine capacity of your Model 1300 It is listed on the hangtag supplied with your Model 1300 Under appropriate circumstances at a range or other suitable shooting location load your magazine to full capacity and make note of the number of shells Remember total capacity includes an additional round which can be loaded manually in the chamber in addition to a full magazine INITIAL CLEANING OILING Some metal parts of your new Model 1300 have been coated at the factory with a rust preventative compound Before using your Model 1300 clean the
6. REINSTALLATION OF THE TRIGGER GUARD GROUP Be careful when reinstalling the trigger guard group Never force parts into position The bolt assembly slide arms and barrel should be attached before installing the trigger guard group The hammer should be in the cocked position and the safety in the on safe position Carefully insert the trigger guard group into place It may be necessary to slide the forearm into different positions until the trigger guard group fits flush into the receiver When properly installed it will fit easily and the pin will slide in without excessive force Installing the bolt assem bly after the trigger guard group is installed should not be attempted Consequently make sure you have already installed the bolt assembly before installing the trigger guard group It is not necessary that the barrel already be attached to install the trigger group Install the trigger group as follows 1 Turn your shotgun over with the open bottom of the receiver facing upward Hold the trigger guard group at an angle to the receiver about 45 degrees and then engage the front tabs on the trigger guard group with the corresponding slots in the magazine throat at the forward end of receiver opening as shown earlier in Figure 13 2 Rotate the trigger guard group towards and into the receiver opening until it is parallel with the receiver 3 Align the trigger guard group with the hole in the receiver and install the
7. anti rust compound from the inside of the barrel receiver breech bolt mechanism and the action chamber areas A high quality lightweight gun oil should be used to remove this compound and to give your new gun its first lubrication Clean the barrel using a cleaning rod and patch as explained under Cleaning and Maintenance Suggestions found on page 25 in this owner s manual First lubrication gt suggestions are outlined below Before beginning assembly of your Model 1300 you should first wipe the mechanism clean and apply a few drops of quality oil on the indicated surfaces Figure 2 NI U AMi Firing Pin Bolt u Lugs EF Magazine Tube Continued on page 8 MODEL 1300 FEATURES The rugged rotary bolt design engages The advanced high strength alloy the barrel extension instead of the top receiver is much lighter than steel of the receiver Stocks are profiled for an ideal fit Several materials and finishes are available rei pe Convenient push button safety Deluxe recoil pad for maximum comfort Choice of barrels Choose standard ventilated rib models with the WinChoke system rifled barrels with rifle sights for shooting slugs smoothbore barrels with rifle sights or models with shorter smoothbore barrels with the WinChoke system WinChoke threaded choke system st 4 Model 1300 field guns feature a fully floating Most Model 1300 hunting models are fitted with the
8. is upward or on top For general parts terminology refer to Figure 1 The Winchester Model 1300 is also shown disassembled Ejection Port Receiver J Buttstock Trigger Guard Disconnector Release Button Reverse Side Trigger Recoil Pad to the extent necessary in order to follow the instructions contained in this owner s manual Figure 12 page 20 Figure 2 covers the general features and benefits of the Model 1300 design Throughout this owner s manual the action refers to the mechanism of this shotgun which loads and secures the shells in the chamber SERIAL NUMBER The serial number is located on the left side of the receiver just above the trigger guard Record the serial number at the front of this book for future reference AMMUNITION All current 12 and 20 gauge Model 1300s have a 3 chamber and are designed to shoot all factory loads such Magazine Loading Port Ventilated Rib WinChoke System Forearm Magazine Cap as 3 Magnum 2 Magnum 2 High Velocity 2 Field and Target loads The barrel can safely shoot both lead and steel shot Special rifled choke tubes and rifled barrels are designed for shooting sabot type slugs Winchester ammunition is always an excellent choice for your new Winchester shotgun delivering unmatched performance and dependability MAKE SURE YOU USE ONLY THE EXACT AMMUNITION GAUGE AS LISTED ON THE LEFT SIDE OF THE BARREL WINCHESTER
9. the trigger guard CAUTION THE RED WARNING BAND ON THE SAFETY BUTTON IS FOR CONVENIENCE ONLY DO NOT DEPEND ON THE RED COLOR ALONE TO INDICATE YOUR GUN S SAFETY STATUS AS TIME EXPOSURE TO THE ELEMENTS AND THE ABRASIVE ACTION OF CLEANING AGENTS CAN ERASE IT Never rely totally on your gun s safety button It is merely an aid to safe gun handling Like any mechanical device the safety can possibly fail it can be jarred or inadvertently manipulated into an unsafe condition Always keep your shotgun pointed in a safe direction At all times in the field keep the safety in the on safe position and the barrel pointed in a safe direction It is a good idea never to load your shotgun until you are in the field and shooting is imminent or until you are at your station at a range and it is your turn to shoot For extra safety and as a courtesy to others fully unload and place the action in the open position at all times other than when shooting is immediately imminent IT IS ESSENTIAL THAT YOU BECOME VERY FAMILIAR WITH THE FEEL LOOK AND OPERATION OF THE SAFETY ON THIS SHOTGUN BEFORE ATTEMPTING TO LOAD AND SHOOT IT INITIAL ASSEMBLY TAKEDOWN ASSEMBLY Remove the barrel assembly and receiver stock section from the carton Be sure you have wiped them clean and oiled them as explained on page 5 Unscrew the magazine cap from the magazine tube Because the magazine spring is held in place by a friction type magazine spring ret
10. through the front of the receiver as it does on the 12 gauge model 1 Remove the barrel and trigger guard group as explained earlier but do not replace the magazine cap 2 You must disengage the slide arms from the slide arm bridge Remove the slide arms through the front of the receiver Remove the bolt slide assembly through the trigger guard group opening REMOVAL OF THE FIRING PIN Begin with the breech bolt assembly removed from the gun 1 Grasp the breech bolt assembly bottom side up flat side and push the rear of the firing pin forward with your forefinger While holding the firing pin in this position take your other hand and tilt the front end of the slide arm bridge and move it slightly forward Lift up on the slide arm bridge and disengage the curved FIGURE 14 tongue on the slide arm bridge from the groove in the firing pin This will detach the slide arm bridge from Position the bolt assembly on the breech bolt slide the slide arms 12 ga 2 The firing pin is under spring tension and will snap out the rear of the breech bolt when your forefinger releases it Control the pin as you remove the firing pin and spring For cleaning purposes no further dismantling is necessary or recommended Do not disassemble your Model 1300 further than shown in Figure 11 shown on page 20 Doing so may void your warranty For repairs that require further on the firing pin is centered in the round hole in the disassembl
11. trigger guard pin from the RIGHT side of the receiver ejection port side until it is flush with both sides of the receiver The pin should pass through easily with little force If significant resistance is felt remove the trigger group and repeat step one 25 Your Model 1300 shotgun is now fully assembled Immediately confirm that the safety is in the on safe position Take time to wipe down and clean all external surfaces as explained under Cleaning and Maintenance Suggestions below CLEANING AND MAINTENANCE SUGGESTIONS Your Model 1300 will function better and more reliably over a longer period of time if it is properly maintained and kept clean BEFORE PERFORMING ANY CLEANING PROCEDURES ALWAYS MAKE CERTAIN THERE ARE NO SHELLS IN THE CHAMBER MAGAZINE OR ACTION FEED AREAS You should clean your Model 1300 after every day of shooting and more often if it becomes excessively dirty A minimum cleaning includes wiping down the action and oiling key parts Most regular maintenance will also include cleaning the barrel If you encounter a function problem tight action when working the forearm be sure to give your gun a thorough cleaning to see if it solves the problem before seeking the services of our service facility or a competent gunsmith To clean your firearm adhere to the following general guidelines CLEANING PROCEDURES ALWAYS PLACE THE SAFETY IN THE ON SAFE POSITION BEFORE BEGINNING ANY CLEANIN
12. under Parts Service Repair and Questions on page 27 OTHER CLEANING SUGGESTIONS e Never pour large quantities of oil into the receiver or other parts It can drain down to the wood and soften it causing permanent damage and loosening of the stock e After extended periods of heavy use your gun should be taken to a qualified gunsmith to have the action disassembled for professional cleaning and lubrication CLEANING PARTS WITH SPECIAL FINISHES Be especially careful when cleaning guns with camouflage Dura Touch Armor Coating and other special finishes 21 Always prevent these surfaces from coming in contact with cleaning solvents barrel scrubbers and other strong chemicals It is preferable to clean these surfaces with a light gun oil containing no solvents or with a damp cloth and mild dish soap be sure to keep water out of the action When cleaning your firearm s bore and action protect the external finishes from any contact with chemicals used Also avoid any contact between external finishes and other strong chemicals like those found in DEET containing insect repellents sunscreens etc Damage to camouflage Dura Touch and other finishes caused by chemicals is irreversible and unrepairable PARTS SERVICE REPAIR AND QUESTIONS If your Winchester rifle or shotgun should ever need service or repair it is often best to utilize one of our Authorized Service Centers In some cases it is appropriate to
13. ER 1 Depress the disconnector release button found behind 10 the trigger guard on the left side Figure 5 to unlock the action without releasing the hammer N Open the action and place the safety in the on safe position The red warning band must not be visible 3 With the magazine pointed in a safe direction unscrew and remove the magazine cap Be careful the magazine spring and magazine plug are retained by a friction type retainer ALWAYS KEEP THE MAGAZINE POINTED AWAY FROM YOU AND OTHERS WHEN REMOVING THE MAGAZINE CAP 4 With one hand grasp the barrel ahead of the barrel bracket hold the buttstock with your other hand Pull the barrel to disengage it from the receiver Slide the barrel bracket off the magazine Do not use excessive force Immediately replace the magazine cap and hand tighten at least three turns Reassembly of the barrel to the action is explained in the previous section LOADING PROCEDURES FIRING A SINGLE SHOT Use the correct ammunition referenced by the inscription on the barrel Before loading your gun be sure all grease and oil have been removed from the barrel and chamber and there are no obstructions Depress the disconnector release button found behind the trigger guard on the left side This unlocks the action without releasing the hammer DI Open the action and place the safety in the on safe position The chamber is now ready to be loaded
14. G PROCEDURE AND BE CERTAIN YOUR GUN S CHAMBER AND MAGAZINE ARE UNLOADED ALWAYS WEAR PROTECTIVE SAFETY GLASSES DURING ALL CLEANING PROCEDURES KEEP AMMUNITION AWAY FROM THE CLEANING AREA DO NOT TEST THE FUNCTION OF YOUR FIREARM WITH LIVE AMMUNITION 1 Use a cleaning rod with a tip and patch suitable for the size of your Model 1300 s bore Make sure the patch is large enough for a snug fit in the bore Insert the rod and patch into the barrel at the receiver end and run it back and forth several times 2 Inspect the chamber and bore for lead and powder fouling A normal amount of powder residue can be expected and is not serious It can usually be removed by repeating step one using a patch saturated with solvent If fouling should become heavy it can be removed with a brass bore brush Dip or spray the brush with solvent and scrub the chamber and bore until the fouling is removed To prevent brass bristles from breaking off the brush should be pushed completely through the bore before being withdrawn 26 3 After fouling has been removed the bore should be wiped dry Then pass a lightly oiled patch through the bore for preservation A fine light gun oil is recommended 4 Wipe all exposed metal surfaces of the receiver forearm and barrels with a clean rag Finger marks should be removed because they provide a place where moisture can accumulate Any dried oil in the receiver area should also be removed 5 Lightly oil
15. SURE YOUR SHOTGUN IS FULLY UNLOADED AND THE MUZZLE FIGURE 11 Carefully tap on the dove tail to adjust windage IS POINTED IN A SAFE DIRECTION PLACE THE SAFETY IN THE ON SAFE POSITION UP OR DOWN ELEVATION ADJUSTMENTS Adjusting elevation on your Model 1300 requires you to lift up the rear notch blade on your shotgun s rear sight with your fingers and move the notched elevator either forward or backward To raise point of impact use your fingers to lift up on the blade and slide the elevator rear ward Adjusting the sight to make your gun shoot lower is just the opposite move the elevator forward Remember e Move the blade up to shoot higher e Move the blade down to shoot lower 18 RIGHT OR LEFT WINDAGE ADJUSTMENTS On most Model 1300 sights the entire rear sight blade holder is dovetailed in the rear sight base To adjust for windage gently move the rear sight blade to the right by tapping at the dovetail using a wood dowel or similar material that will not mar the sight Figure 11 Your gun will now shoot more to the right Moving the blade holder to the left is just as easily done Note how much you adjust the sight as you sight in your Model 1300 Remember e Move the rear sight to the right to shoot farther to the right on the target e Move the rear sight to the left to shoot farther to the left on the target SCOPE BASE MOUNTING INSTRUCTIONS Some Model 1300 shotguns are designed to
16. VING OR INSTALLING A CHOKE TUBE MAKE ABSOLUTELY CERTAIN THE GUN IS FULLY UNLOADED AND THE ACTION IS LOCKED OPEN NEVER ATTEMPT TO REMOVE OR INSTALL A SHOTGUN CHOKING DEVICE ON A LOADED FIREARM DO NOT FIRE THIS SHOTGUN WITHOUT HAVING THE WINCHOKE CHOKE TUBE INSTALLED PERMANENT DAMAGE MAY RESULT TO THE THREADS Failure to follow these warnings may cause damage to your gun and cause injury to yourself and others 14 TUBE REMOVAL 1 Place the safety in the on safe position and fully unload your Model 1300 ALWAYS UNLOAD YOUR MODEL 1300 COMPLETELY INSPECT THE CHAMBER MAGAZINE AND FEED MECHANISM TO MAKE SURE THEY DO NOT CONTAIN ANY SHELLS 2 Open the action 3 Use the WinChoke spanner wrench to loosen the tube turning it counterclockwise Figure 8 Finger twist the tube the rest of the way out of the barrel TUBE INSTALLATION 1 Place the safety in the on safe position and fully unload your Model 1300 ALWAYS UNLOAD YOUR MODEL 1300 COMPLETELY INSPECT THE CHAMBER MAGAZINE AND FEED MECHANISM TO MAKE SURE THEY DO NOT CONTAIN ANY SHELLS 2 Open the action and lock it open as explained previously 3 Before installing a tube check the internal choke tube threads in the muzzle as well as the threads on the WinChoke choke tube to be sure they are clean Lightly oil the threads with a quality light gun oil 4 Using your fingers screw the appropriate tube into the muzzle end of the barrel ta
17. a brass brush to clean your gun unless a choke tube is installed in the barrel Bristles could break off and lodge in the threads making installation and removal of choke tubes difficult N Regularly remove your gun s tube in order to clean and CHOKE PATTERN CONVERSION CHART LEAD STEEL Extra Full Full i Improved Modified Full Modified Full Improved Cylinder Modified Skeet Improved Cylinder Cylinder Cylinder x not for use with steel shot oil the threads inside the barrel as well as on the choke tube itself This will protect the threads from being damaged and also prevent dirt build up that would cause the choke tube to become difficult to remove from the barrel Clean the threads with solvent and a small soft brush like a toothbrush Wipe completely clean and leave a thin film of clean oil on the threads both on the tube and in the barrel The threads of the choke tube and the internal threads of the barrel should be cleaned after each use and before the installation of a tube SN Be careful when removing or installing a tube Use the specially designed WinChoke spanner wrench Damage can result to both the choke tube and the barrel when attempting to remove sticky choke tubes 4 Never fire your shotgun or run cleaning tools through the barrel of any choke tubed gun without having a choke tube installed REMOVING THE MAGAZINE PLUG When hunting migratory birds Federal Law mandates the use of a magaz
18. accept a scope or other optical sight usually these are turkey and deer models The receiver tops of some of these models are drilled and tapped for scope bases while some models are equipped with a cantilever scope base If your shotgun has a cantilever mount follow the mounting instructions supplied with your scope rings and or scope If your shotgun s receiver is drilled and tapped for scope mounts four holes in line in pairs on top of the receiver will be visible They are fitted with filler screws If yours is drilled and tapped you must adhere to the following WARNING YOUR WINCHESTER SHOTGUN IS DRILLED AND TAPPED FOR THE MOUNTING OF BASES AND RINGS TO ACCOMMODATE AN APPROPRIATE SCOPE OR SIGHT ALWAYS USE THE CORRECT BASES FOR THIS SHOTGUN WITH THE APPROPRIATE LENGTH SCREWS WHICH ARE AT LEAST 2 IN LENGTH To mount scope bases on your Model 1300 shotgun perform the following steps 1 MAKE SURE YOUR SHOTGUN IS COMPLETELY UNLOADED Check the magazine chamber and feed mechanism to be sure no shells are present Leave the action open Make sure you place your shotgun on a table or other safe secure location Protect the finish with rags or other padding 2 You should have two Model 1300 compatible bases and four screws of at least 11 2 in length MAKE SURE YOUR BASES ARE COMPATIBLE WITH YOUR MODEL 1300 3 Clean all oil grease or dirt from the receiver top and from the scope base parts 4 Position your shot
19. ainer always be careful which direction the end of the magazine is pointed ALWAYS KEEP THE MAGAZINE POINTED AWAY FROM YOU AND OTHERS WHEN REMOVING THE MAGAZINE CAP Your shotgun will usually come out of the box with the bolt assembly in the closed position forward with the trigger assembly already in place in the receiver The barrel can be installed with the action closed but it is easier if the action has been opened slightly To unlock and open the action without pulling the trigger push up on the disconnector release button at rear of the trigger guard Figure 5 on the left side and pull back on the forearm Once the action is open perform the following steps 1 Grasp the barrel ahead of the barrel bracket 2 Position the barrel over and in line with the magazine tube FIGURE 5 Press the disconnector release button to unlock the action 3 Slide the barrel rearward D Guide the barrel bracket over the end of the magazine tube and guide the barrel extension into the receiver Be sure that the slot in the barrel aligns with the ejec tor As a guide in assembly align the rib on the barrel assembly with the grooves on the top of the receiver mn Slide the barrel rearward until it seats in the receiver ON Immediately replace the magazine cap Tighten it hand tight at least three full turns to ensure secure engagement TAKEDOWN FIRST BE CERTAIN THERE ARE NO SHELLS IN THE MAGAZINE OR CHAMB
20. as been cycled through the chamber and out the ejection port leave the action open 6 Using your index finger feel the entry of the magazine to make sure there are no longer any shells in the magazine ALTERNATE WAY TO UNLOAD The shells can also be removed from the magazine by following these steps 1 Place the safety in the on safe position make sure the action is closed and keep the muzzle pointing in a safe direction N Turn the gun over so the trigger guard is facing up then push the carrier down as far as it will go SN Push inward on the right of the cartridge cutoff to release a shell from the magazine Figure 7 Press the cutoff again to release the second shell The cartridge cutoff is located on the inside right of the ejection port When a shell is in the magazine the cutoff rests on the brass of the shell With the safety still in the on safe position press the disconnector release button and move the forearm all the way rearward to remove the shell from the chamber EN 2 Press the cartridge stop inward to release shell from magazine WARNING ALWAYS OPEN THE ACTION AND VISUALLY CHECK THE CHAMBER TO BE CERTAIN THAT YOUR SHOTGUN IS UNLOADED FIRING PROCEDURES 1 When you are ready to shoot with a loaded shell in the chamber the safety in the on safe position and your finger off the trigger push the safety to the off safe position with the red
21. cope as outlined in the One of the advantages of a Model 1300 is the ability to instructions supplied with your scope rings and or disassemble the action for cleaning Under very harsh scope Always make sure you have the proper eye relief weather conditions and in dirty environments just knowing Always make sure that the saddle crossbolts and the that parts are clean and lightly oiled can add an extra cap bolts are fully tightened before using your shotgun measure of confidence to your shooting experience Make sure you have a clean place to work and a good place to put the components as they are disassembled Figure 12 FIGURE 12 Barrel WinChoke Tube Barrel Bracket r r P N f m NVI U Magazine Spring Firing Pin Spring Be Bolt Slide Magazine Plug N Slide Arm Bridge EL r WAR 1 m Breech Bolt Magazine Magazine Firing Pin Spring Retainer Follower Magazine Cap Magazine Tube Trigger Guard Crop Slide Arms Forearm ane Guard Pin WEAR EYE PROTECTION AT ALL TIMES NEVER DISASSEMBLE BEYOND WHAT IS EXPLAINED AND SHOWN IN THIS OWNER S MANUAL Disassembling the action can be done in the field but remember there are small parts involved some of which are under spring tension First be certain there are no shells in the magazine or chamber REMOVAL OF THE BARREL 1 Open the action and make sure the gun is unloaded 2 Close the action and place the safety in the on safe position
22. e assemblies into the front of the receiver As the assemblies enter the receiver slide them fully rearward Figure 15 REASSEMBLY OF THE FIRING PIN BREECH BOLT AND SLIDE 20 GAUGE ONLY 1 Reinstall the firing pin spring over the firing pin Either end can go on first 2 Insert the firing pin and spring into the rear opening of the bolt slide pin end first 3 To reinstall the bolt assembly on the slide arm bridge push or compress the knob end of the firing pin sufficiently into the hole in the bolt slide so that the large space between the grooved knob and the 24 flange on the firing pin is centered in the round hole in the bolt slide 4 Place the curved tongue located on the slide arm bridge into the space between the knob and flange and slowly release pressure on the end of the firing pin Let the flange on the pin pull the tongue toward the rear of the bolt assembly This should hold the breech bolt assembly and the slide arm bridge together during further assembly 5 With the trigger guard group removed insert the bolt assembly through the trigger guard opening up into the receiver The front face and extractor of the bolt assembly should be facing the barrel or front of the shotgun The slide arm bridge should be facing down toward the trigger guard group opening 6 While holding the bolt assembly in place insert the slide arm bars into the breech and connect them to the slide arm bridge
23. ep barrel chamber and action free of rust Rust in the barrel and chamber can cause excessive pressures resulting in serious injury A rusted pitted or eroded barrel should be replaced 9 Use hearing protection to prevent ear damage from repeated exposure to gunfire 10 Always use proper shooting glasses to prevent eye injury from flying particles vn 16 Discharging firearms in poorly ventilated areas cleaning firearms or handling ammunition may result in exposure to lead and other substances known to cause birth defects reproductive harm and other serious physical injury Have adequate ventilation at all times Wash hands thoroughly after exposure 11 Never carry a loaded gun in a motor vehicle or carry one into a dwelling Always carefully unload the gun before entering a motor vehicle a dwelling or an area such as a camp Always point your gun in a safe direction while loading or unloading to prevent serious injury in case of an accidental discharge Never load your gun in a house or in a vehicle GENERAL DESCRIPTION 12 Never shoot at a hard flat surface or at the surface of i i No pump shotgun is faster than the Winchester Model water to avoid a ricochet and possible serious personal 1300 In fact the Model 1300 is so fast we call it the injury to yourself or a bystander 2 Speed Pump 13 Store guns in a clean dry place out of reach of children and separated from stored ammunition I 6 In more wa
24. estions e Links to helpful sites Go to www winchesterguns com NOTES 29 NOTES 30 NOTES 31 RIFLES AND SHOTGUNS Winchester Firearms 275 Winchester Avenue A YA Morgan UT U S A 84050 9333 Y f www winchesterguns com
25. gun in the upright position with the top of the receiver upward 5 Remove all four filler screws from the top of the receiver using a very small thin bladed gunsmithing type screwdriver 19 6 Pre position the bases on the receiver top to determine the best orientation of the bases Most bases have transverse grooves cut into them that are offset from the middle These are the grooves that the crossbolts in your scope rings will pass through The grooves are offset to allow you to position the bases to fit the design length of your scope and the placement of the scope front to back for proper eye relief Place both grooves to the rear both to the front or one in each direction depending on your scope and desired position 7 Once you know which configuration you will use insert the screws through the bases and screw them into the receiver top using the correct wrench or screwdriver usually a 2 hex wrench YOU MUST USE SCREWS WHICH ARE AT LEAST 42 IN LENGTH TO ENSURE PROPER THREAD ENGAGEMENT Many gunsmiths find it helpful to use a drop of serviceable thread locking compound to assure the screws stay tight Make sure the compound does not get into the action BE CAREFUL TO ASSURE THAT THE THREADS OF EACH SCREW ENGAGE PROPERLY IN THE THREADS IN THE RECEIVER TO PREVENT STRIPPING THE THREADS IN THE ALLOY RECEIVER 8 Tighten the screws snugly but do not overtighten COMPLETE DISASSEMBLY 9 Mount your scope rings and s
26. igger The safety may not prevent an accidental discharge due to dropping jarring or bumping a gun Use only ammunition for which the gun is chambered as indicated on the barrel to prevent excessive pressure and possible serious personal injury Incorrectly reloaded ammunition can cause serious personal injury and damage to the firearm due to excessive pressure Reload only after proper instruction and in strict compliance with instructions and data contained in current reloading manuals Never point a gun at anything you do not intend to shoot Always keep it pointed in a safe direction in case of accidental discharge Always check to ensure that the barrel is free of obstructions before loading and using the gun If you experience light recoil or off sound check the barrel for an obstruction Before firing clean any grease or oil out of the barrel with a cleaning rod and patch Grease or heavy accumulation of oil can cause excessive pressures and result in serious personal injury 15 Hunting from elevated surfaces such as tree stands is dangerous Doing so may increase the risks of handling any firearm Always make certain that the stand being used is safe sturdy and stable Always make certain your firearm is unloaded when it is being taken up and down from the stand Always make certain that your firearm is not dropped from the stand or dropped while it is being taken up or down from the stand 8 Ke
27. igger guard pin by pushing it out from the LEFT side of the receiver the side opposite the ejection port Any sturdy pushing tool that is smaller in diameter than the pin and will not mar the finish is acceptable Make sure you can maintain a good grip on the pushing tool and on your shotgun while you push FIGURE 13 After removing the pin tilt the rear of the trigger guard group up then lift it out 6 Push the pin through sufficiently until it can be grasped with your fingers Pull it the rest of the way out If it cannot be removed with fingers make sure your pushing tool or punch has a diameter small enough so that it will push the pin completely through without the tool damaging the hole 7 With the pin removed lift the trigger guard group out of the receiver by lifting upward and pulling rearward Figure 13 DISASSEMBLY OF THE SLIDE AND BREECH BOLT 12 GAUGE ONLY 1 Remove the barrel and trigger guard group as explained earlier but do not replace the magazine cap 22 2 With the action slide arms still attached to the slide arm bridge simultaneously slide both assemblies forward and out of the front of the receiver Note that as the breech bolt assembly passes by the ejection port there may be some resistance from the ejector spring Carefully work it past the resistance DISASSEMBLY OF THE SLIDE AND BREECH BOLT 20 GAUGE ONLY This procedure is necessary because the bolt will not extract out
28. ine restriction device that only allows a total of three shells to be held in your shotgun at one time WHEN REMOVING THE PLUG BE CERTAIN THERE ARE NO SHELLS IN THE MAGAZINE OR CHAMBER AND KEEP THE BARREL AND MAGAZINE POINTED IN A SAFE DIRECTION 16 FIGURE 9 Carefully pry up on the magazine spring retainer Catch the components as they spring out AT ALL TIMES REMEMBER THE PLUG IS UNDER SPRING PRESSURE SO CARE MUST BE TAKEN FOR SAFE REMOVAL ALWAYS POINT THE END OF THE MAGAZINE AWAY FROM YOUR FACE AND IN A SAFE DIRECTION ALWAYS WEAR EYE PROTECTION WHEN REMOVING AND REINSTALLING THE MAGAZINE S THREE SHOT PLUG The magazine plug is spring loaded and can thrust out of the magazine when the friction type magazine retainer is removed too quickly Never look directly into the cap end of the open magazine 1 Remove the magazine cap 2 Place one hand over the retainer and pry it up slowly with a screw driver using your other hand Figure 9 When the retainer releases you will feel the pressure of the friction ring and plug on the palm of your hand Magazine plug supplied with Ladies Youth Models FIGURE 10 CATR AI Se fee r A et a ro wt nn WE TREE TER HERE se ee Ice enge i yar RU SENT MI se Ne Te SEN S SIEHE De a LE EDEN THAT ER wei r gt a ee ee ar F Se gt Single shot lt 2shots total 3 Slowly raise your hand and let the magazine spring relax Capture the parts in y
29. nual for your convenience GENERAL OPERATION The Model 1300 is a pump action shotgun that allows you to load a round by cycling the action to eject the empty shell and move an unfired shell from the loaded magazine tube to the chamber This can be repeated until the magazine is empty A single round can also be inserted into the chamber manually The Model 1300 breaks down for easy cleaning and storage Prior to using live ammunition familiarize yourself thoroughly with the operating instructions in this owner s manual Get accustomed to the feel of your new gun and know the forces required to operate the action Learn how to pull the trigger and above all know the location and operation of the safety Procedures for disassembly and operation of various components are outlined later in this owner s manual Please read and study them thoroughly In addition always remember WARNING ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION USE THE CORRECT AMMUNITION REFERENCED BY THE INSCRIPTION ON THE BARREL BEFORE LOADING YOUR GUN BE SURE ALL GREASE AND OIL HAVE BEEN REMOVED FROM THE BARREL AND CHAMBER AND THERE ARE NO OBSTRUCTIONS TERMINOLOGY AND DESCRIPTIONS Descriptions in this owner s manual generally refer to the gun in the horizontal position that is in the normal firing position For example the muzzle is forward or front the butt stock is rearward or rear the trigger is downward or underneath the sight
30. our hand as they spring out 4 With the spring relaxed the friction ring plug spring and follower can be removed To reinstall reverse this procedure RANGER COMPACT MODELS ONLY The Ranger Compact 1300s are specially equipped with a segmented plug that can be cut to adjust the number of shells that can be loaded into the magazine A full length plug with no segments removed turns this Model 1300 into a single shot when installed into the magazine As you become more experienced with your Model 1300 the first section of the plug can be cut off at the segment notch allowing one shell to be held in the magazine Figure 10 With more experience the other sections of the plug can 17 maA n lt 3 shots total be removed to facilitate more shells in the chamber When the entire plug is removed four shells can be loaded into the magazine with one also in the chamber SIGHT ADJUSTMENTS Some Model 1300 shotguns are fitted with rifle type open sights The style and adjustment system may vary between models and grades The proper procedure is to shoot a eroup with the sights set as they come from the factory intermediate position on both elevation and windage and then make incremental adjustments to move the sight blade and blade holder to position the group on your target The procedures below are for the most common type of open sights found on Model 1300 shotguns BEFORE MAKING ANY SIGHT ADJUSTMENTS MAKE
31. pair Center ARC page 27 13 WINCHOKE CHOKE TUBE SYSTEM Some Model 1300s are fitted with the interchangeable WinChoke choke tube system If your shotgun has the words WinChoke inscribed on the side of the barrel then you have this system The WinChoke system allows you to configure your Model 1300 for the pattern and or choke constriction your shooting situation demands It also offers versatility when using slugs or sabots A variety of WinChoke choke tubes are available for use in your Model 1300 including models designed for use with sabot type slugs Your Model 1300 is provided with the WinChoke screw in choke tube system This gives you the finest possible patterns for target and field situations Plus it is extremely easy to switch choke constrictions to match your shooting conditions WinChoke tubes are fully compatible with steel and lead shot A special choke tube spanner wrench is provided to remove and tighten these tubes CAUTION DO NOT USE WINCHOKE TUBES IN ANY SHOTGUN BARRELS NOT SUPPLIED BY U S REPEATING ARMS COMPANY THE MAKERS OF WINCHESTER BRAND FIREARMS ALSO DO NOT USE ANY OTHER CHOKING DEVICE IN ANY SHOTGUN BARRELS SUPPLIED BY U S REPEATING ARMS USE ONLY THE APPROPRIATE GAUGE AND TYPE OF CHOKE TUBES MARKED WINCHOKE IN FIGURE 8 Use the spanner tool to remove or tighten WinChoke tubes YOUR MODEL 1300 SHOTGUN CAUTION WHENEVER HANDLING ANY SHOTGUN FOR THE PURPOSE OF REMO
32. pered end first knurled end outward When it becomes finger tight use the WinChoke choke tube spanner wrench to firmly seat the tube Figure 8 Do not overtighten or forcefully tighten with wrench CHOKE TUBES SHOULD BE PERIODICALLY CHECKED TO ASSURE THAT THEY ARE TIGHT AND FIRMLY SEATED BEFORE CHECKING FOLLOW THE SAFETY GUIDELINES OUTLINED ABOVE Replacement and additional tubes and wrenches are available from your Winchester firearms dealer WINCHOKE CHOKE IDENTIFICATION To identify individual WinChoke choke tubes refer to the abbreviated indications on the outside rim of each tube SELECTING THE CORRECT WINCHOKE TUBE The WinChoke choke system is fully compatible with factory lead or steel shot loads The chart at right includes both lead and steel shot information Lead and steel shot perform differently in tubes with the same choke constriction For this reason both lead and steel shot designations have proven necessary In fact even larger steel shot diameters result in different patterns than smaller steel shot sizes Each designation is inscribed on each choke tube 15 SPECIAL NOTE ON SHOTGUN SLUGS Cylinder or Improved Cylinder WinChokes are suitable for shooting rifled slugs or sabot type slugs Never shoot slugs or sabots in any WinChoke barrel with the choke tube removed SPECIAL CARE OF CHOKE TUBES AND CHOKE TUBE THREADS 1 If your gun is equipped with WinChoke choke tubes do not use
33. stions 27 Website Information 2 22 cc 28 GUN SAFETY WARNINGS IT IS ESSENTIAL THAT THESE OPERATING INSTRUCTIONS BE THOROUGHLY STUDIED BEFORE USING THIS FIREARM TO ASSURE PROPER AND SAFE GUN HANDLING FAILURE TO FOLLOW THESE INSTRUCTIONS OR FAILURE TO OBEY ANY SAFETY WARNING MAY RESULT IN INJURY TO YOURSELF OR OTHERS OR CAUSE DAMAGE TO YOUR GUN As a gun owner you accept a set of demanding responsibilities How seriously you take these responsibilities can be the difference between life and death There is no excuse for careless or abusive handling of any firearm At all times handle your shotgun and any other firearm with intense respect for its power and potential danger PLEASE READ AND UNDERSTAND ALL OF THE CAUTIONS PROPER HANDLING PROCEDURES AND INSTRUCTIONS OUTLINED IN THIS OWNER S MANUAL BEFORE USING YOUR NEW FIREARM 1 Do not carry a loaded gun with a live round in the chamber while walking running climbing a tree crossing a fence or anywhere you might slip or fall drop the gun or otherwise bump or jar the gun A gun that is dropped bumped or jarred with a chambered round might accidentally discharge even with the safety on Causing serious injury to you or someone else When Ws you are ready to shoot and a round is chambered keep the safety on Do not rely on the safety to prevent accidental discharge Many safeties merely block the trigger and prevent firing by pulling the tr
34. use the Winchester Firearms Service Center in Arnold MO A list of Authorized Service Centers was included with your new firearm If you need a new listing call us We can help you determine the best place to service your firearm In order to avoid delays it is important to obtain direct authorization from one of our service specialists before sending your firearm to our facility This avoids possible delays in obtaining service Call us for complete details on how to receive service before sending your gun Parts listings Service Center lists service procedures and general product information are also found on the Web at www winchesterguns com GENERAL PRODUCT AND HISTORICAL QUESTIONS Winchester Firearms 275 Winchester Avenue Morgan UT 84050 9333 1 800 945 5237 toll free PARTS SERVICE REPAIR STATUS AND TECHNICAL QUESTIONS Winchester Firearms Parts and Service 3005 Arnold Tenbrook Road Arnold MO 63010 9406 1 800 322 4626 toll free CAUTION PARTS ARE MADE FOR WINCHESTER BRAND GUNS MANUFACTURED BY OR FOR WINCHESTER FIREARMS U S REPEATING ARMS COMPANY INC AND SHOULD NOT BE USED IN OTHER GUNS EVEN THOUGH MODELS MAY BE SIMILAR IMPROPERLY FITTED PARTS MAY BE DANGEROUS 28 WEBSITE INFORMATION Winchester Firearms offers an information resource for you on the World Wide Web e List of Authorized Repair Centers e Customer Service information e Answers to many technical and historical qu
35. ventilated rib On all barrels as the barrel heats WinChoke system It allows you to change choke with shooting dimensions can vary slightly The constriction to the demands of the game being hunted Faster inertia assisted pumping The rotary bolt disengages 1300 s floating rib design allows the rib to move You can easily change the pattern size and density by from the barrel fractions of a second after the shell fires without distorting your sight plane simply switching tubes A variety of accessory choke The bolt is forced rearward by inertia actually assisting you tubes are available as you pump the forearm rearward for the next shot Avoid applying too much oil Only a light film is necessary Excessive oil should be wiped off especially in cold weather CLEANING PARTS WITH SPECIAL FINISHES Be especially careful when cleaning guns with camouflage Dura Touch Armor Coating and other special finishes Always prevent these surfaces from coming in contact with cleaning solvents barrel scrubbers and other strong chemicals It is preferable to clean these surfaces with a light gun oil containing no solvents or with a damp cloth and mild dish soap be sure to keep water out of the action When cleaning your firearm s bore and action protect the external finishes from any contact with chemicals used Also avoid any contact between external finishes and other strong chemicals like those found in DEET containing insect repellents
36. warning band fully visible Your shotgun is now ready to fire with a pull of the trigger REMEMBER THE RECOIL FROM A SHOTGUN ESPECIALLY WITH MAGNUM LOADS WILL BE SOMEWHAT HEAVIER THAN MOST OTHER GUNS FIRMLY SHOULDER YOUR MODEL 1300 TAKE AIM AND WHEN ON TARGET SQUEEZE THE TRIGGER N Pull the forearm fully rearward until the fired shell is ejected out the ejection port SN Push the forearm fully forward transferring a new shell from the magazine into the chamber Your Model 1300 is again cocked and ready to fire Immediately put the safety in the on safe position with the red warning band hidden until you are ready to fire again IN THE CASE OF A MISFIRE Only rarely will modern factory ammunition experience a misfire If this ever happens to you when shooting your Model 1300 please follow these instructions carefully CAUTION IN CASE OF MISFIRE KEEP THE BARREL POINTED IN A SAFE DIRECTION CAREFULLY OPEN THE ACTION WHILE AVOIDING DIRECT EXPOSURE TO THE BREECH BY YOURSELF AND OTHERS REMOVE THE SHELL FROM THE CHAMBER FULLY UNLOAD YOUR SHOTGUN REMOVING ALL SHELLS FROM THE MAGAZINE Carefully inspect the ejected shell If the primer is indented the shell should be disposed of in a manner that would prevent accidental injury to you others or the environment If there is no indentation your gun has malfunctioned and should be serviced by a qualified gunsmith or by a Winchester Firearms Authorized Re
37. y contact a Winchester Firearms Authorized kolksiide Service Center or a qualified gunsmith as explained under Parts Service Repair and Questions on page 27 4 Place the curved tongue located on the slide arm bridge into the space between the knob and flange and REASSEMBLY OF THE FIRING PIN BREECH BOLT AND slowly release pressure on the end of the firing pin Let SLIDE 12 GAUGE ONLY the flange on the pin pull the tongue toward the rear of the bolt assembly This should hold the breech bolt assembly and the slide arm bridge together during further assembly 1 Reinstall the firing pin spring over the firing pin Either end of the spring can go on first 2 Insert the firing pin spring assembly into the rear opening of the bolt slide pin end first 5 With the firing pin and breech bolt now assembled engage the slide arm bridge into the matching cuts on 3 To reinstall the bolt assembly on the slide arm bridge the slide arms Figure 14 push or compress the knob end of the firing pin sufficiently into the hole in the bolt slide so that the 6 Hold the slide arms and bolt slide arm bridge large space between the grooved knob and the flange assemblies together Start the forearm assembly onto the magazine tube 23 FIGURE 15 Carefully guide the bolt assembly on the slide arms into the receiver 7 Remove the magazine cap and carefully guide the slide arms and bolt slide arm bridg
38. your gun at the points described under Initial Cleaning Oiling found on page 5 Ordinary good judgment will of course indicate that the metal of the gun should receive a light film of oil any time the gun has been exposed to weather or handling This is very important and must be done with every firearm even stainless steel models Remember the polished finely fitted surfaces of the receiver and action mechanisms must always have a thin film of oil Make sure that the surfaces of the locking pin system and the hinge components are especially clean and lightly oiled with a high quality gun oil INSPECT THE BARREL AND CHAMBER MAKE CERTAIN THAT NO PATCHES HAVE BEEN INADVERTENTLY LEFT IN THEM REMOVE ANY THAT REMAIN 7 Wipe all wood surfaces with a soft cloth 8 When transporting only store your Model 1300 in a quality protective case to prevent scratches and dents Store in a dry place to prevent corrosion Store away from children MAKE SURE YOUR SHOTGUN IS UNLOADED AND ALWAYS STORE AMMUNITION SEPARATELY DO NOT TAKE YOUR GUN S ACTION OR TRIGGER GROUP APART BEYOND WHAT IS EXPLAINED IN THIS MANUAL Your Model 1300 is a specialized finely fitted mechanism You may permanently mar it by attempting to disassemble the inner mechanism assemblies If further disassembly for service or cleaning is required take your gun to a Winchester Firearms Authorized Service Center or a a a qualified gunsmith as explained
39. ys than one it s the pump that thinks it s a semi auto A fraction of a second after you pull the 14 Never alter any parts of your gun Any alterations trigger and fire a Model 1300 the lugs of the ultra strong or adjustments that may become necessary to the operating mechanism should be performed by a qualified gunsmith rotary bolt begin disengaging from the barrel extension Recoil forces still present in the gun then assist the slide rearward You can feel the slight rearward force on the forearm as you shoot which makes it much easier to begin your pumping action You ll soon find that you will complete the pumping action forward quickly and without conscious effort In a brief instant you ve cycled a shell and are ready for a second shot Speed like this makes a big difference allowing you to set up for a second shot more quickly and concentrate on your target not just on pumping With the Model 1300 s rotary bolt design the lugs engage directly in the lug recesses in the barrel extension This is an unusually strong consistent and reliable lockup design Every design feature of the Model 1300 works together to make what many consider the most reliable pump shotgun on the market today Your new Model 1300 is one of a number of different versions and configurations offered The basic operating procedures are the same for nearly all of them Where there are differences they are pointed out in this owner s ma
Download Pdf Manuals
Related Search