Home

Rack User Manual Remote Control Interface RCI10

image

Contents

1. 2 02220222002000 2000 20 7 General RCI10 Additional functions SSH surface u2000 2000a000naan0naanunnnnunnnnunnanunnanunnannnnnnnnnnnnnnnn 20 7 1 Operation of the SSH surface Display RCI10 inventory data aeaaaae e aaa aa nnnn nenne nnnne nennen 21 7 2 Operation of the SSH surface Download of log data and measuring data file 21 7 3 Operation of the SSH surface Reset to factory settingS esaaa aaa aaa a aaa aaa aaaa zana nennen 22 7 4 Operation of the SSH surface RCI10 software update upgrade e aaeeaaae aa aaa nenne nnnnenn 22 8 General RCI10 Operation with web DrowWSel cssscssscesccnsecsscensensecnseessensecnseensensecessensennseesssnsenseees 22 8 1 Operation with web browser Function of the mask Fuse Control eszaaeeaaae anawa aaaaazaaaaziacce 22 8 2 Operation with web browser Function of the mask Feed Settings ooocccccnnccconnoconnocannncannnnas 24 8 3 Operation with web browser Function of the mask Fuse Settings cccccccsecccsssecceseeseseeseeeeaes 25 8 4 Operation with web browser Function of the mask System LOQ cccsscccsseeeseseeseeeeseeesaeeesaes 27 8 5 Operation with web browser Function of the mask Error Log cccsscccsseeeceeeeceeeeeeseeseneeseeesees 28 8 6 Operation with web browser Function of the mask Fuse Log ccccccccsseeeceeeeceseee
2. z Es p Date of issue Date of publication August 2015 This document replaces the following documents New Edition Editor E T A Elektrotechnische Apparate GmbH Industriestra e 2 8 D 90518 Altdorf GERMANY Phone 49 9187 10 0 Fax 49 9187 10 397 E Mail info e t a de www e t a de Copyright 2015 E T A GmbH The contents of this document are the property of E T A GmbH No part of this publication must in any way be reproduced or distributed without prior written consent of E T A GmbH Any person acting illegally with regard to this publication can be prosecuted Limitation of liability Although all provisions were taken when creating this document the editor does not accept any responsibility for errors or omissions or for damages caused by using the information contained in this document The information contained in this document may be revised at any time without advance notice Brands All references to software and hardware in this document are generally protected by brands or patents E T A GmbH 2015 All rights reserved About this manual This manual describes the configuration for start up and the operation of the integral SSH web browser and SNMP interfaces by means of a control and configuration PC connected to the Remote Control Interface RCI10 The RCI10 sub assembly provides ease of monitoring and remote control of the Contro Plex Rack system in connection with a control computer or a manage
3. SSH settings Description Factory settings Setting parameters SSH user login Defines the user name user ID for the SSH login Permitted characters 20 characters a z 0 9 _ SSH user password Defines the password for the SSH login Please observe upper and lower case Permitted characters 110 characters a z A Z 0 9 HTTP settings Description Setting parameters HTTP enable Activation web server Allow access via web browser Possible values Yes No Access only using HTTPS Web browser access only via HTTPS protocol possible encrypted transmission Possible values Yes No Allow settings write Parts of the configuration settings such as http login IP address etc can Yes be changed directly via webbrowser Possible values Yes No Y Factory settings Yes Yes es Allow fuse switch via Determines if the circuit protectors may be switched ON or OFF via the HTTP web browser surface Possible values Yes No HTTP access is Web browser access only possible with user ID and password http and Yes password protected https Possible values Yes No HTTP login Defines the user name user ID for the web browser access Permitted characters 20 characters a z 0 9 _ HTTP password Defines the password for the web browser access Please observe upper and lower case Permitted characters 20 characters a z A Z 0 9 amp 0 4 H _ lt gt N HTTP language Defines the language for the w
4. Defines the password for an SNMP v3 connection Please observe upper and lower case Permitted characters 20 characters a z A Z 0 9 amp 0 2 _ lt gt M SNMP authentication SNMPv3 authentication method Possible values MD5 SHA SNMP encryption SNMPVv3 encryption method methode Possible values AES off DES SNMP encryption key SNMPv3 key used for data encryption Permitted characters 500 characters a z A Z 0 9 amp _ 3 lt gt M NTP settings Description Value Setting parameters NTP enable Activate NTP Client automatic time synchronisation via external server Possible values Yes No IP address or URL of the NTP server from where the time information shall be obtained Permitted characters 100 characters a z A Z 0 9 Time zone Adjust time zone time difference between local time and UTC Possible values 12 1 0 1 12 Example 1 Central European winter time 2 Central European summer time DST Calculate with summer time and winter time Possible values Yes No Ethernet settings Description Setting parameters Enable IPv4 Value Activation of the IPv4 address range for addressing the RCI10 sub assembly Should you be able to set this value to No the RCI10 can no longer be addressed via IPv4 Possible values Yes No Use DHCP for IPv4 Activate DHCP for IPv4 If activated an IPv4 address is automatically assigned via the conne
5. and changeover summertime wintertime DST A Date and clock time cannot be set because the factory settings include an NTP server time server network time protocol The RCI10 sub assembly will automatically get the valid time information from the NTP server It may however happen that the NTP server cannot be reached by your local network see chapter 6 4 Start up Table of SSH configuration parameters and factory settings e Click on SAVE to save the changed values If you do not save all changes will be lost Click on the button REBOOT EXECUTE to activate all changes confirm with OK The RCI10 sub assembly carries out a reset with a re load of the changed parameters Re booting may take up to 60 seconds During this time you do not have a connection to the RCI10 sub assembly A The reset will not affect the plugged in circuit protectors ESX300 S i e your connected loads remain active during the RCI10 re start e Re load the page in your web browser after approx 60 seconds Click on the Reload function of the web browser Now all carried out changes should be activated and visible 6 General RCI10 Start up with the SSH v2 surface Secure Shell or SSH is the name of a network protocol and of corresponding programmes For the purpose of a safe encrypted connection between the configuration PC and the RCI10 sub assembly also via an unsafe network the SSH surface can be used both for a comprehensive configuration of all param
6. 56 117 Fuse new __ F11 Type 0x80 Serial 4294967295 SW Version 2 0 1 HW Version 0x0001 Nominal current 8 A Load current 0 00 A Operating voltage 39 V Temperature 30 C Err Fig 18 Web mask System Log A By clicking on the button Download you open the log file in a CSV format excel or save on your PC 27 8 5 Operation with web browser Function of the mask Error Log In the mask Error Log you can retrieve and display all internal messages of the RCI10 interface sub assembly The log file can additionally be loaded up onto the configuration PC Example Mask Error Log TontrolPlex Rack GEFA Intelligent Power Distribution ENGINEERING TECHNOLOGY Error Log 1 01 01 1970 01 01 28 89 1 bus failure events detected during the last 60 seconds 0 01 01 1970 01 03 01 182 Enter fault mode Could not read back own transmission Bytes received so far 4401054000b9 Page Up Page Down Log Page Auto scroll Fig 19 Web mask Error Log A By clicking on the button Download you open the log file in a CSV format excel or save on your PC 28 8 6 Operation with web browser Function of the mask Fuse Log In the mask Fuse Log you can retrieve and display all measuring values of each installed electronic circuit protector such as voltage load current and temperature The measuring data file can additionally be uploa ded onto the configuration PC and
7. 7 1 Operation with SSH surface Display RCI10 inventory data A These data can also be obtained via the web surface or the SNMP interface You can retrieve inventory data of the RCI10 sub assembly such as software version hardware version serial number and others including production data and check sum of the software via the menu option System Info Fig 13 SSH system information submenu 7 2 Operation with SSH surface Download of log data and measuring data file A This function is also available via the web surface Open a submenu via the menu option Export Log with the option to download the following log files e System Log gt messages regarding the ControlPlex Rack system such as plug in or pull a circuit protector short circuit trip etc Error Log gt internal failure indication of the RCI10 sub assembly Fuse Log gt measuring data regarding current voltage and temperature of all installed circuit protectors The storage time in the RCI10 sub assembly is at least 30 hrs depending on the number of circuit protectors and the pre set measuring cycle time A The saved measuring data file is saved in a CSV excel format i e it can be analysed and processed further by means of a simple excel script Download can be carried out following the description in chapter 6 5 start up RCI10 configuration file Download via the Z Modem function of the SSH Client programme LePutty 21 7 3 Operation with SSH surface
8. Reset to factory settings A This function is also available via the web surface In the event of faulty configuration entries or if you cannot remember which value you entered how and where you reset all configuration parameters to the factory settings under menu option Reset all settings to default 1 Navigate in the SSH menu window with the Cursor buttons 1 to the menu option Reset all settings to default and press Enter A There will be no feedback from the system However the factory settings were copied into the memory 2 Navigate in the SSH menu window with the cursor buttons 1 to the menu option Reboot RCI10 and press Enter The factory settings will now be re activated Re boot is visually indicated by the green LED going out Repeated access of the RCI10 is possible approx 60 seconds after initiation of the re boot The IPv4 and the login settings for new log on into the system can be found in table 2 SSH configuration parameter list and factory settings 7 4 Operation with SSH surface RCI10 software update upgrade On our website www e t a de Controlplex_rack you can check if a new software version is available for your RCI10 sub assembly for downloading In the event of a software update please proceed as follows 1 Load the new software version onto your configuration PC 2 Save the configuration data as described in chapter 6 5 start up RCI10 configuration file download 3 Navigate in the SSH menu window wi
9. duty A No fields for a threshold value entry will be shown for empty slots Example Mask Fuse Settings Fields and check box Select circuit protector for threshold value entry or load channel Fuse Settings Select Fuse to modity Parameter for fuse F1 Label e A Refresh Switch off Undervoltage a V Range 40 68 Switch back on Undervoltage a V Range 42 70 Switch off Current EJ A Range 0 30 Switch off Temperature a C Range 10 90 Switch back on Temperature a C Range 0 80 Delete all Switch oft at lime 24h w hh nim E Delete and de activate Switch on at Time 24h the threshold values Fuse state atter Reset f i i of all circuit protectors in the memory Save the Time entry and start of Delete and deactivate values entered values a reset function After for the indicated circuit protector expiration of the time there will be switched ON Fig 17 Web mask Fuse Settings with description Please proceed as follows for setting threshold values 1 Select the load channel you wish to edit by means of the circuit protector number 2 Activate the check box es on the left side of the entry field s e g for a voltage dependent ON and OFF operation 3 Enter a threshold value in the corresponding field s 4 Save the settings in the RCI10 sub assembly by clicking the button Save Settings The entered settings will thus be activated 5 If possibl
10. o o Load out ON OFF Q Q Q Fig 5 Web mask Fuses e Click on the tab Configuration on the left side of the surface The configuration window System Settings opens ControlPlex Rack EFA Intelligent Power Distribution ENGINE A System Settings ETHERNET MISC Login eta MIOS Y System name Password M a System contact i Language IPv4 Address System location IPv4 Mask IPv4 Gateway set Time Set Date Enable IPv6 v Timezone Use DHCPv6 Y DST v IPv6 Address IPv6 Prefix Length Reboot DNS server eset to Factory Defaults Fig 6 Web mask Configuration System settings 11 5 5 Start up Configuration by means of web browser surface The web browser configuration window shows the presently active factory settings The tab Configuration contains three tabs System Settings Feed Settings Fuse Settings This chapter describes the setting options of the System Settings A Please note that depending on the internal factory set configuration or the configuration carried out by you via the SSHv2 interface some functions may not be available A Please make a note of all configuration changes with the newly entered values Please carry out the following adjustments in the category HTTP e _ Change the user name under Login Change the password under Password A The password is not shown asterisks No password is set in the event of no entry Change the disp
11. supply Entries valid for supply Entries valid for supply group A Feed A group B Feed B Redundant version only If not activated any set threshold values will automatically be deactivated after an RCI10 re boot ControlPlex Rack GEFA Intelligent Power Distribution ENGINEERING TECHNOLOGY Feed Settings GLOBAL Enable Feed Monitor a aftor Reset Save the entered values PEREDA Switch off Undervoltage o V Range 40 68 Mean Value Swilch back on Undervoltage m V Range 42 70 Mean Value Switch off total Curren Sum Value Switch off Temperature E C I Range 10 90 Mean Value Switch back on Temperature Y C Range 0 80 Mean Value EJ A Range 1 999 FFED B Swilch olf a Undervoltage V Range 40 68 Mean Value Swilch back on Undervoltage m BR V ange 147 70 Mean Value Switch off total Current Sum Value Switch off Temperature EJ C Range 10 90 Mean Value Switch back on Temperature EU C Range 0 80 Mean Value B A I Range 1 999 E m Refresh Delete and deactivate all entered values in the memory DU Fields for threshold value entry Checkbox only upon activation will the entered threshold values switched ON Fig 16 web mask Fuse Control with description Please proceed as follows for setting threshold values 1 Activate the check box es on the left side of the entry field s e g for a voltage depende
12. the menu option Reboot RCI10 in the SSH menu so that the changes are activated Re boot can also be effected by pressing the reset button of the RCI10 sub assembly for 3 seconds on site Re boot is visually indicated by the green LED going out The RCI10 can be accessed again approx 60 seconds after initiation of the re boot The reset will not affect the plugged in circuit protectors ESX300 S i e your connected loads remain active during the RCI10 re start if the configuration value status after reset was set to ON in the web browser surface or was not activated see chapter 8 3 operation with web browser Function of the mask Fuse Set tings If you changed the IP address of the RCI10 sub assembly you are no longer able to open the RCI10 SSH surface For this purpose you need to enter the changed RCI10 IP address also in the LePutty programme see LePutty window fig 7 IP configuration LePutty Host Name or IP address Save the change by clicking on the button Save in the LePutty window 1 see chapter 12 Legal references and licences 15 6 4 Start up Table of SSH configuration parameters and factory settings Description of all available SSH configuration parameters including the factory setting when delivered A Please note that depending on the internal factory set configuration or the configuration carried out by you via the SSHv2 interface some functions may not be available
13. 0 characters a z 0 9 _ SSH user password Defines the password for the SSH login Please observe upper and lower case Permitted characters 110 characters a z A Z 0 9 HTTP settings Description Value Setting parameters HTTP enable Activation web server Allow access via web browser Possible values Yes No Access only using HTTPS Web browser access only via HTTPS protocol possible encrypted transmission Possible values Yes No Allow settings write Parts of the configuration settings such as http login IP address etc can be changed directly via webbrowser Possible values Yes No Allow fuse switch via Determines if the circuit protectors may be switched ON or OFF via the HTTP web browser surface Possible values Yes No HTTP access is Web browser access only possible with user ID and password http and password protected https Possible values Yes No HTTP login Defines the user name user ID for the web browser access Permitted characters 20 characters a z 0 9 _ HTTP password Defines the password for the web browser access Please observe upper and lower case Permitted characters 20 characters a z A Z 0 9 amp 0 40 H _ lt gt N HTTP language Defines the language for the web browser surface Possible values english german SNMP settings Description Setting parameters SNMP enable Activation of SNMP access In OFF condition no SNMP commands will be accepted b
14. 10 IPv4 factory pre set address has not yet been assigned otherwise in your local network For a list of all factory settings please see table 2 SSH configuration parameter list and factory settings 5 4 Start up Starting the web browser surface e Open a web browser window on your configuration PC e g with Internet Explorer or Mozilla FireFox etc e Enter the URL https 192 168 0 25 in the address line and confirm with the Return button e Should a warning message appear such as Problem with the security certificate please confirm with continue or continue loading of the indicated page e Enter user name and password The factory pre set user name is user password user1234 Confirm with OK Windows Sicherheit iexplore Der Server 192 168 0 25 fordert Ihren Benutzernamen und Ihr Kennwort an Der Server ist von Password protection A e Anmeldedaten speichern OK Abbrechen Fig 4 Web browser login IE e The web browser surface opens with the tab Fuse Control of the RCI10 sub assembly Depending on the ver sion of the Contro Plex Rack system the appearance may slightly differ whether you installed a redundant system or not control Plex Rack Intelligent Power Distribution Fuse Control n N m na N Short circuit Overload Compare Mode Undervoltage All On Overvoltage Overtemperature No Vcc Load out status Load Current A o G o
15. 68 0 20 62466 192 168 0 25 22 150 01 01 1970 01 08 38 519 User configuration started user user SSH connection 192 168 0 20 62465 192 168 0 25 22 149 01 01 1970 01 07 10 431 User configuration started user user SSH connection 192 168 0 20 62460 192 168 0 25 22 148 01 01 1970 01 07 06 427 User configuration started user user SSH connection 192 168 0 20 62450 192 168 0 25 22 147 01 01 1970 01 07 04 425 User configuration started user user SSH connection 192 168 0 20 62458 192 168 0 25 22 146 01 01 1970 01 06 00 361 User configuration started user user SSH connection 192 168 0 20 62454 192 168 0 25 22 145 01 01 1970 01 05 58 357 User configuration started user user SSH connection 192 168 0 20 62452 192 168 0 25 22 144 01 01 1970 01 05 53 354 User configuration started user user SSH connection 192 168 0 20 62451 192 168 0 25 22 143 01 01 1970 01 04 53 294 User configuration started user user SSH connection 192 168 0 20 62448 192 163 0 25 22 142 01 01 1970 01 00 18 19 System restart after power up 141 01 01 1970 01 00 23 24 Fuse new __F3 Type 0x82 Serial 4294967285 SW Version 2 0 0 HW Version 0x0001 Nominal current 5 A Load current 0 00 A Operating voltage 40 V Temperature 28 C Error 140 01 01 1970 01 00 17 18 System restart after power up 139 01 01 1970 01 03 04 185 User configuration started user user SSH connection 192 168 0 1 49483 102 168 0 25 22 138 01 01 1970 01 01
16. 68 0 25 is occupied by RCI10 factory settings Example Set an IPv4 address at the configuration PC e g IPv4 192 168 0 20 Eigenschaften von Internetprotokoll Version 4 TC D P E za Allgemein IP Einstellungen k nnen automatisch zugewiesen werden wenn das Netzwerk diese Funktion unterst tzt Wenden Sie sich andernfalls an den Netzwerkadministrator um die geeigneten IP Einstellungen zu beziehen IP Adresse automatisch beziehen 6 Folgende IP Adresse verwenden IP Adresse 192 168 0 20 Subnetzmaske 255 255 255 0 Standardgateway DNS Serveradresse automatisch beziehen 6 Folgende DNS Serveradressen verwenden Bevorzugter DNS Server Alternativer DNS Server _JEinstellungen beim Beenden berpr fen Erweitert OK Abbrechen Fig 3 IPv4 setting configuration PC 5 3 Start up Status and installation of the hardware The ControlPlex Rack system with the components ESX300 S circuit protector and RCI10 Remote Control Interface was installed correctly as described in the ControlPlex Rack Mounting and Installation Instruc tions The LED status is as follows e RCI10 status LED shows green e ESX300 S fault LED s OFF e ESX300 S OK LED s blink slowly or show green Your PC is connected with a LAN Ethernet cable to the RJ45 connector of the RCI10 sub assembly The PC and RCI10 sub assembly can also be interconnected via a network e g router For this purpose please ensure that the RCI
17. SNMP v1 or v2c you need the Community String used by the management system If you use SNMP v3 you need the SNMPv3 authentication method MD5 SHA of the management system If you use SNMP v3 you need the SNMPv3 encryption method AES Off DES of the management system 9 7 W If you use SNMP v3 you need the SNMPv3 data key entered in the management system If all data listed above are known you configure the SNMP settings of the RCI10 sub assembly as described in chapter 6 3 Start up configuration via SSH surface et sqq Please also see excerpt below table 4 SSH SNMP settings SSH settings Description Factory settings Setting parameters SNMP enable Activation of SNMP access In OFF condition no SNMP commands will be Yes accepted by a management system Possible values Yes No SNMP protocol Determination of the permitted SNMP protocol The RCI10 supports SNMP v v2 v3 Data are transmitted encrypted only with v3 Possible values v1 v2 v3 Enable traps Permit the sending of SNMP traps If in the ON condition alarm message can immediately be reported without a query from the superordinate system management system Possible values Yes No Trap target The IP address or the host name of the system to which the SNMP traps alarm or status indication shall be sent When entering more than one address they have to be separated by a semicolon Allow fuse switch Determines if the circuit protectors may be switched ON
18. aaa aaa zana nr non 23 15 web mask Fuse G ntrol with deseription eisen a adw ATZ Gi O Ew ase 23 16 web mask Feed Settings with description 0u00020000 00n00nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnsnnnnnnnnnnnnnsnnnnnsnnnnnnnnne 25 1 2 web mask Fuse Settings WIN GCESCHPTIOIN aaa iw ARG a nee 26 18 IES System LOG dies 27 19 WED mask EMO LOG ea O ra 28 20 Web Mask Fuse LO code usas tees 29 215 ONMEVMIB Mea as 31 11 Appendix List of abbreviations ControlPlex Rack DHCP DC ESX300 S Ethernet EMC HTTP HTTPS LePuTTY MIB NTP PDB RCI10 SNMP SSH Terminal URL Web Browser electronic power distribution system with electronic circuit protectors ESX300 S and interface sub assembly RCI10 Dynamic Host Configuration Protocol Direct Current electronic circuit protector for DC 48 V DC 60 V standardised interface for cable connected data networks electromagnetic compatibility Hypertext Transfer Protocol open transmission Hypertext Transfer Protocol Secure encrypted transmission Internet Protocol Client Programme with SSH protocol support Management Information Base programme part which can be embedded in a management system and which communicates via an SNMP protocol Network Time Protocol automatic time synchronisation Power D Box power distribution system Remote Control Interface sub assembly Simpl
19. aeeesaeeesaeeeeaes 29 9 General RCI10 operation with management SYSTEM cc ccsscesseneeenseensensecnscenseeseenseensennseeseensenneees 29 9 1 Operation with management system Settings in the RCI10 sub assembly asesaauaaaaaaa 30 9 2 Operation with management system Embed SNMP MIB esaaaeaaaae e aaa aaa aaeaaaaaaazaweaaaece 31 10 Appendix LISTOFDICUTES ae an 32 11 Appendix List OF abbreviations ani iaa 33 12 Appendix Legal references and licences 2 2202200200200n0nnnnnnnnnun nun nun nnnnnnn nun nun nun nun m nun nun nun mann nennen 34 13 Appendix Template of configuration table 2 2 200200nn00n0nn0nnunnnnnnnnnun nun nun nun nun nnun nun nnnnunn nun nen 35 14 Appendix Example RCI10 configuration file excerpt 220 2000000n000n0n ann nnunnnnnnnnn nun n nun nnEnnnn 38 NOLES ER dos 39 1 Introduction You chose ControlPlex Rack a comprehensive future oriented protection system which combines safety user convenience and service friendliness It is a power distribution measurement and control system which provides electronic and in the event of a short circuit current limiting protection of various loads By means of an internal bus system and an additional hot pluggable control interface module optional each load can remotely be controlled and monitored In addition it allows recording of measuring data of every single load Besides providi
20. arious protocols can be carried out via the SSH surface If you do not want to use the web browser surface you may skip this chapter Continue with chapter 6 General RCI10 Start up with the SSH v2 surface The web browser surface provides the following adjustment options for network and start up configuration Configuration e P address data e Web browser log on data e System time e Settings of the Contro Plex Rack system specific system designations e Setting the system language of the web browser surface 5 1 Start up Useful information on the web browser surface For using the web server function you only need a web browser on your PC We tested the following browsers with regard to correction function and display e Internet Explorer Version 9 e Mozilla Firefox Version 28 8 1 e Google Chrome Version 26 0 You are of course free to use other web browsers or versions of the above listed browsers However in such a case we cannot ensure that all charts of the web browser surface will be shown correctly 5 2 Start up IP settings on the configuration PC Before starting configuration you have to check the IPv4 Ethernet settings on the configuration PC and amend them if required For this purpose connect your PC with a LAN Ethernet cable to the RJ45 connector of the RCI10 sub assembly The IPv4 Ethernet address of your configuration PC has to be as follows 192 168 0 xxx Comment xxx 1 24 26 254 the address 192 1
21. ark the menu item Session Basic options for your PuT TY session in Category Specify the destination you want to connect to Host Name or IP address Port 192 168 0 25 22 Connection type 2 Mark in menu item Saved Session Raw O Telnet Rlogin SSH Sera the file RCI10_Config Vxx 3 Click on button Load Fig 7 IP configuration LePutty see chapter 12 Legal references and licences 13 2 Configure the ZModem settings see fig 8 bottom Carry out the steps 1 to 5 beside the picture left and right 1 Mark the menu item ZModem in Category z 2 Click on button Browse A browser window opens ategory E Bel Options controlling Z Modem transfers Navigate and mark the file saved in chapter 6 1 rz Features Window EOS and click on open E Command Behaviour rz exe i Translation i Selection assis Colours Send command 3 Click on button Browse A browser window opens E oczy Command 5 Enter the values ep Navigate and mark the file saved in chapter 6 1 sz e v in the fields and click on open Options 4 Click on button Browse A browser window opens Select the directory where you wish to save the ControlPlex measuring and configuration data Fig 8 ZModem configuration LePuT TY e Mark the menu item Sessions in Category see fig 7 IP configuration LePuT TY top e Click the button Save to save the carried out ZModem set
22. can there automatically be evaluated e g by means of an excel macro Example Mask Fuse Log Page Up Page Down Log Page Auto scroll W Fuse Log Time Fuse 1 Fuse 2 F2 Contro Plex Rack GEFA Intelligent Power Distribution ENGINEERING TECHNOLOGY Fuse 6 Fuse 8 Fus F6 F8 F Volt Temp Load Flags Volt Temp Load Flags Volt Temp Load Flags Volt Temp Load Flags Volt Temp Load Flags Volt Temp Load Flags Volt Temp Load Flags Volt Temp Load Flags Volt Temp 01 01 1970 05 43 28 41V 32 C 0 024 O 01 01 1970 2 42 55 41V 36 C 0 02A O 01 01 1970 O 05 42 24 41v 38 C 001A O ee 41V 36 C 0 02A O ee 41V 38 C 0 02A O r o 41V 36 C 0 02A O ao HV 38 C 0 02A O 01 01 1970 05 39 49 TV 38 C 0014 O 01 01 1970 A 05 30 18 41V 38 C 0 02A O 01 01 1970 05 38 47 01 01 1970 05 38 18 41V 36 C 0 01A O 41v 36 C 0 02A O 01 01 1970 05 37 45 01 01 1970 05 37 14 41v 36 C 0 02A O 41v 36 C 0024 O 01 01 1970 s 05 36 43 41V 33 C 0 024 O 41V 33 C 000A O 41V 34 C 0 00A O 41V 34 C 0 00A O 41V 34 C 000A O 41V 34 C 0 00A O 41V 34 C 0004 O 41V 34 C 0 00A O 41V 33 C 000A O 41V 34 C 000A O 41V 34 C 0 00A O 41V 34 C 000A O 41V 34 C 0 00A O 41V 34 C 0 00A O 41V 34 C 000A O Fig 20 Web mask Fuse Log A By clicking on the button Download you open the log file in a CSV format excel or save on your PC 9 General RCI10 operation with ma
23. cted network Possible values Yes No IP address IPv4 address RCI10 sub assembly Example format xxx xxx xxx xxx Network mask IPv4 network mask RCI10 sub assembly Example format xxx xxx xxx xxx Gateway IPv4 gateway of the current network segment Example format xxx xxx xxx xxx DNS server IPv4 IPv6 IPv4 address of the Domaine Name Server DNS Example format xxx xxx xxx xxx Enable IPv6 Activation of the IPv6 address range for addressing the RCI10 sub assembly sub assembly Possible values fYes No Use DHCP for IPv6 Activate DHOP for IPv6 If activated an IPv6 address is automatically assigned via the connected network Possible values Yes No IP address IPv6 address RCI10 sub assembly Example format 2001 db8 1 2 305 811 1 Network prefix length Enter the IPv6 length of the network prefix Possible values 3 characters 0 9 DNS server IPv4 IPv6 IPv6 address of the Domaine Name Server DNS Example format 2001 db8 1 2 3C5 811 1 ey 6 RCI10 settings Description Setting parameters Period duration in seconds with which measuring values of each ESX300 S circuit protector will be written into the log file e g load current voltage and temperature values Possible values off 30 600 Fuse log periodicity Option to reset all setting parameters listed in this table to the factory settings When entering No the menu option Reset to factor
24. e Network Management Protocol Secure Shell encrypted transmission Client Programm see LePutty Uniform Resource Locator the www address of a website Programme for display of http https protocol data such as the Microsoft internet explorer 33 12 Appendix Legal references and licences SSH Client Programme LePutty The programme LePutty was not changed or adjusted by E T A in any way E T A tests the software to our best knowledge before making it available for download on our website However E I A does not assume liability for failures caused by misuse or software errors or malicious codes in the programme The version tested and made available on the E T A website refers to LePutty 0 53b It is based on Putty Beta Release 0 53 Build Date 3rd October 2006 LePutty is based on the programme Putty See PuTTY LePutty homepage legal notice licences and copyright PuTTY PuTTY is copyright 1997 2015 Simon Tatham http www chiark greenend org uk sgtatham putty LePutty http leputty sourceforge net E T A ControlPlex Rack download area SSH Client Software http www e t a de controlplex_rack Software Licenses ControlPlex Rack see http www e t a de licenses 34 13 Appendix Template of configuration table Print table and enter values SSH settings Description Setting parameters SSH user login Defines the user name user ID for the SSH login Permitted characters 2
25. e between the different electrical devices should be applied Technical Accuracy All technical data in this manual were correct in all conscience at the time of printing E T A cannot be held liable for any inadvertent errors Due to continuous product improvements at E T A there could be discrepancies between the actual product and the manual Product changes or amendments of the technical specifications will be carried out without prior notification The latest versions of the Contro Plex Rack documents are available on our website www e t a de 4 Schematic system design and network connection Schematic diagram of entire system ControlPlex Rack line entry supply LINE load 1 Circuit Protector ESX300 S 1 Sig C EL Bus Sig NC backplane load 19 Ethernet Interface Fig 1 Schematic diagram ControlPlex Rack Connection example SNMP v1 v2c v3 HTTP S SSH management system main computer ControlPlex Rack r PDB N CP HI router Ethernet cable ESX300 S SE o gt Sad configuration PC system cabinet Fig 2 Connection example ControlPlex Rack 5 General RCI10 Start up with web browser surface The web server included in the RCI10 sub assembly offers an easy and convenient option of adjusting the RCI10 sub assembly and the ControlPlex Rack system to your requirements during start up An extended configuration for enhanced security settings of v
26. e for addressing the RCI10 Yes sub assembly Should you be able to set this value to No the RCI10 can no longer be addressed via IPv4 Possible values Yes No Use DHCP for IPv4 Activate DHCP for IPv4 If activated an IPv4 address is automatically assigned via the connected network Possible values Yes No IP address IPv4 address RCI10 sub assembly 192 168 0 25 Example format xxx xxx xxx xxx IPv4 network mask RCI10 sub assembly Example format xxx xxx xxx xxx Gateway IPv4 gateway of the current network segment Example format xxx xxx xxx xxx DNS server IPv4 IPv6 IPv4 address of the Domaine Name Server DNS Example format xxx xxx xxx xxx Enable IPv6 Activation of the IPv6 address range for addressing the RCI10 sub assembly Possible values Yes No Use DHCP for IPv6 Activate DHCP for IP v6 If activated an IPv6 address is automatically Y assigned via the connected network Possible values Yes No IP address IPv6 address RCI10 sub assembly Yes es Example format 2001 db8 1 2 3C5 811 1 Network prefix length Enter the IPv6 length of the network prefix Possible values 3 characters 0 9 DNS server IPv4 IPv6 IPv6 address of the Domaine Name Server DNS Example format 2001 db8 1 2 3C5 811 1 RCI10 settings Description Factory settings Setting parameters Fuse log periodicity Period duration in seconds with which measuring values of each ESX300 S circuit protector will be writt
27. e test the activated value on the ControlPlex Rack system Repeat steps 2 to 5 for each parameter specific setting of the circuit protector A Please note that the internal date and time configuration of the RCI10 sub assembly will be used when activating the function at time ON OFF If no valid system time is available ON and OFF operation is no carried out correctly In the event of a supply voltage failure date and time indication will be lost no real time clock available A possible solution is the configuration of an NTP server please also see chapter 6 3 Start up Configuration via SSH surface A If the function Fuse state after reset is OFF and the check box activated the load output of the circuit protector will not automatically be switched ON in the event of a supply voltage failure and voltage resto ration or after a re boot of the RCI10 sub assembly This function shall prevent an automatic re start e g of a motor in the event of a power failure safety relevant function A The function Monoflop was implemented particularly for power on off of equipment and it keeps up the physical connection between the Contro Plex Rack system and the control computer i e even in the event of an interruption of the connection when switching off the load output will be reconnected after a pre set time and the connection will be restored 26 A Should you wish to de activate the set values but you do not yet
28. eb browser surface Possible values english german SNMP settings Description Setting parameters SNMP enable Factory settings Activation of SNMP access In OFF condition no SNMP commands will be Yes accepted by a management system Possible values Yes No SNMP protocol Determination of the permitted SNMP protocol The RCI10 supports SNMP v1 v2 v3 Data are transmitted encrypted only with v3 Possible values v1 v2 v3 Enable traps Permit the sending of SNMP traps If in the ON condition alarm messa Yes ge can immediately be reported without a query from the superordinate system management system Possible values Yes No Trap target The IP address or the host name of the system to which the SNMP traps alarm or status indication shall be sent When entering more than one address they have to be separated by a semicolon Allow fuse switch Determines if the circuit protectors may be switched ON or OFF via the Yes SNMP protocol Possible values Yes No Allow settings write Parts of the configuration settings such as snmp login IP address etc Yes can be changed directly via SNMP management system Possible values Yes No SNMP community string SNMP community string of the RCI10 sub assembly If the protocol version SNMPv1 or SNMPv2c is used the management system has to know the string indicated here The value entered here is valid for the parameters read and write Perm
29. en into the log file e g load cur rent voltage and temperature values Possible values off 30 600 Allow reset to factory Option to reset all setting parameters listed in this table to the factory Yes defaults settings When entering No the menu option Reset to factory default will disappear Possible values Yes No System name Freely selectable system name Permitted characters 100 characters a z ControlPlex Rack A Z 0 9 amp 4 _ 3 lt gt System contact Freely selectable system contact name e g person to contact on site E T A Altdorf Permitted characters 100 characters a z A Z 0 9 8 amp 49 9187 100 sl System location Freely selectable system location Permitted characters 100 characters a z A Z 0 9 15 8 2 _ lt gt W 17 Time Date settings Description Factory settings Setting parameters Time Enter present time if no NTP server See NTP settings was indicated or is available The parameter NTP enable has to be no for that Format hh mm ss Enter present date if no NTP server see NTP settings was indicated or is available The parameter NTP enable has to be no for that Format DD MM YYYY Time zone Adjust time zone time difference between local time and UTC Possible values 12 1 0 1 12 Example 1 Central European winter time 2 Central European summer time Calculate with summ
30. er time and winter time Possible values Yes No Fuse Labels settings Description Factory settings Setting parameters Label for fuse 1 20 Freely selectable system name for the circuit protector ESX300 S in the F1 F2 F3 F4 F5 F6 slot A1 A20 A1 A10 and B1 B10 Permitted characters 20 F7 F8 F9 F10 F11 F12 characters a z A Z 0 9 8 amp 0 7 _ lt gt N F13 F14 F15 F16 F17 F18 F19 F20 Table 2 SSH configuration parameter list and factory settings 6 5 Start up RCI10 configuration file download For locally saving the changed configuration settings on the configuration PC please navigate in the SSH menu with the Cursor buttons 1 to the menu option Export all settings and press Enter 1 Asubmenu opens Fig 10 SSH export settings 2 Start the file export with the Enter button 3 Navigate with the mouse on the upper SSH window frame Press the right mouse button and select the menu option Zmodem Receive 18 Verschieben Gr e ndern Minimieren Maximieren Schlie en Special Command Event Log New Session Duplicate Session Saved Sessions Change Settings Copy Allto Clipboard Clear Scrollback Reset Terminal Full Screen Zmodem Receive Zmodem Upload About PuTTY Fig 11 SSH Zmodem pull down menu 4 The RCI10 configuration file will be saved on your configuration PC under the name exportSettings ini The memory location on the conf
31. eters and for upload and download of data such as measuring and log data The SSH surface offers you the full scope of configuration options of the RCI10 sub assembly This is particularly relevant for higher requirements of system safety For a list of all factory settings please see table 2 SSH configuration parameter list and factory settings 6 1 SSH tools Installation SSHv2 Client programme LePutty In order to be able to establish a safe SSH v2 connection you require a terminal programme called SSH Client The SSH Client programme has to be installed on the PC used for configuration We recommend the freeware programme LePutty which is available for download on our website www e t a de controlplex_rack The configuration of the SSH Client mentioned below exclusively refers to this version e After downloading the compressed file CP RCIxx_SSH Client_Vxx zip unpack into a suitable directory on the hard disk drive of your configuration PC e Among the unpacked files there is a file named E T A_Readme txt holding all information required for installation Please follow the instructions given in this file 6 2 SSH tools Installation SSHv2 Client programme LePutty To allow use of the full functional scope of LePutty you have to configure the programme as follows 1 Start the programme by clicking on the programme icon Putty Carry out the steps 1 to 3 on right side of fig 7 IP configuration LePutty 1 M
32. ety engineering Safety instructions Please follow the instructions given in this document carefully Failure to comply may lead to serious damages of the product or the system E T A does not accept any liability for problems caused by improper installation or handling by the customer or a third person Symbols You will find the following symbols in the entire manual Their meaning is as follows Danger A You are in a situation which might cause injury Before working on a device you have to be aware of the hazards connected with electrical circuitries and you have to be familiar with the standard procedures of accident prevention Warning A There is a risk in this situation to do something which might cause damage of the devices or data loss Note A Here you receive information which might be particularly useful for the application Contents ABOUT TIS Manuals eines 3 Ger eralnolE O 4 G ntents ita 5 1 IEF OGUICHION A 6 2 Minimum requirements for start up of the RCI10 sub assembly s ssssssseossecssnaznaazaczzncsESaE 7 3 Important information and safety instructions a2022002000n0nn0nnnnnunnunnnnnnnn nun nun nun nun nun n nun nun nnne 7 4 Schematic system design and network connection uu a202a2000n00nnnnnnnunnnunnnnnnnnunnnunnnunnunnnnnun nun 8 5 General RCI10 Start up with web browser surface 22 20002000000n0nnn0nnn0nnnn nun nun ann nun nun nnnn nun m nun
33. g the configuration file by pressing the Enter button again Navigate with the mouse on the upper SSH window frame Press the right mouse button a menu opens Select the menu option Zmodem Upload 6 Abrowser window opens Mark the configuration file meant for uploading ini on your configuration PC and click on Open 7 Wait until the upload to the RCI10 has successfully been completed The SSH window will close auto matically Open a new SSH window Navigate in the SSH menu window with the cursor buttons to the menu option Reboot RCI10 and confirm with the Enter button A The RCI10 sub assembly carries out a re boot The re boot activates the input configuration data in the RCI10 It can take up to 60 seconds until you can access the RCI10 sub assembly again 7 General RCI10 additional functions SSH surface Other helpful SSH functions include the storage of current log or measuring value files and the query of RCI10 system information These functions can be made available to you by means of the web surface In addition you have the possibility to reset all settings you changed to the factory setting in the event of a wrong configuration Upon availability of new functions or bug fixes you can input a software update into the RCI10 sub assembly A Please note that depending on the internal factory set configuration or the configuration carried out by you via the SSHv2 interface some functions may not be available 20
34. ic circuit protectors with regard to short Circuit overcurrent trip under or overvoltage indication etc In addition the individual circuit protectors can be switched on or off manually and additional information can be retrieved 22 Retrieving additional information about a circuit protector Move the mouse pointer to the status indication bar of a circuit protector and the following information will be shown e slot number of circuit protector e current rating of the circuit protector e hardware version of circuit protector e serial number of circuit protector e software version of circuit protector e present load current of circuit protector e present voltage on circuit protector e present temperature of power MOSFET of the circuit protector e name of circuit protector if applicable Additional Slot No Fi Type 0x80 SW Version 2 0 1 Nominal Current A 24 Operating Voltage V Information Label F1 Serial Number 1 HW Version OxOOFF Load Current A 0 03 Temperature C Fig 14 Web mask Fuse Control additional information ESX300 S Example Mask fuse control version with redundant supply total current display total current display power input A power input B only redundant version control Plex Rac Intelligent Power Distribution Fuse Control yes cf related circuit Short circa gt ls protectors e g F1 Overload gt la 77 with F11 only redundant Undervohage gt le All On
35. iguration PC is the path selected in chapter 6 2 para 2 step 4 Fig 12 SSH export configuration file successful 5 Press ESC to return to main menu 6 Change the name ofthe saved configuration file exportSettings ini A meaningful name could be the assigned system name or the installation site of the Contro Plex Rack system 19 6 6 Start up RCI10 configuration by means of configuration file uploads For a software update or when replacing RCI10 sub assemblies you can re input the configuration file saved in chapter 6 5 into the system Should you operate several ControlPlex Rack systems where e g only the IPv4 data are different you are able to edit the configuration file ini and save a new TXT format Afterwards you can input the changed file into a new ControlPlex Rack system A Passwords and user names can not be changed in the INI file In the event of non observance you will lose the RCI10 access A When changing the INI file you have to strictly observe the predetermined syntax Incorrect data e g re garding the IP address format can cause loss of the functionality of the RCI10 sub assembly as well loss of access to it 1 Open an SSH window by means of LePutty to the ControlPlex Rack System Log on to the system with your SSH user name and the password Navigate in the SSH menu window with the cursor buttons 11 to the menu option Import all settings and hit Enter 4 A submenu opens Start importin
36. itted characters 20 characters a z A Z 0 9 8v 4 H _ lt gt N Defines the user name user ID for an SNMP v3 connection Permitted characters 20 characters a z 0 9 _ SNMP password Defines the password for an SNMP v3 connection Please observe upper and lower case Permitted characters 20 characters a z A Z 0 9 amp O _ lt gt N 16 SNMP authentication SNMPv3 authentication method Possible values MD5 SHA SNMP encryption SNMPv3 encryption method methode Possible values AES off DES SNMP encryption key SNMPv3 key used for data encryption Permitted characters 500 characters a z A Z 0 9 amp _ lt gt M ControlPlexRack ESX300 NTP settings Description Factory settings Setting parameters NTP enable Activate NTP Client automatic time synchronisation via external Yes server Possible values Yes No IP address or URL of the NTP server from where the time information shall be obtained Permitted characters 100 characters a z A Z 0 9 ptbtime1 ptb de Time zone Adjust time zone time difference between local time and UTC Possible values 12 1 0 1 12 Example 1 Central European winter time 2 Central European summer time DST Calculate with summer time and winter time Yes Possible values Yes No Ethernet settings Description Factory settings Setting parameters Enable IPv4 Activation of the IPv4 address rang
37. kk password 38 Notes 39 ETTA ENGINEERING TECHNOLOGY Anwenderhandbuch User manual M_19BGTCP_d_310815 E T A Elektrotechnische Apparate GmbH Industriestra e 2 8 90518 ALTDORF A be 01 2015 ae DEUTSCHLAND Alle Rechte vorbehalten All rights reserved Tel 09187 10 0 Fax 09187 10 397 E Mail info e t a de www e t a de
38. know if you will need them again at a later date you only have to de activate the check box es beside the input field s and save the change s Now all threshold values are de activated but still saved 8 4 Operation with web browser Function of the mask System Log The mask allows retrieval and display of all system relevant events that occurred in the ControlPlex Rack The log file can additionally be loaded up onto the configuration PC Example Mask System Log ControlPlex Rack GEFA Intelligent Power Distribution ENGINEERING TECHNOLOGY System Log 171 01 01 1970 02 31 39 5500 User configuration started user user SSH connection 192 168 0 23 53245 192 168 0 25 22 170 01 01 1970 02 17 08 4629 User configuration started user user SSH connection 192 188 0 23 52413 192 188 0 25 22 169 01 01 1970 01 00 23 24 Fuse new __F1 Type 0x80 Serial 4204957205 SW Version 2 0 1 HVV Version 0x00ff Nominal current 24 A Load current 0 00 A Operating voltage 41 V Temperature 28 C Error 168 01 01 1970 01 00 18 19 System restart after power up 187 01 01 1970 01 00 23 24 Fuse new __F2 Type 0x80 Serial 4294967295 SW Version 2 0 1 HW Version OxO0ff Nominal current 24 A Load current 0 00 A Operating voltage 42 V Temperature 26 C Error 166 01 01 1970 01 00 18 19 System restart after power up Page Up 01 01 56 E __F6 Type 0x80 Serial 4294967295 SW Version 2 0 1 HV Version 0
39. lay language if required under Language You can choose between the languages German and English In the category ETHERNET you can e g adjust the IPv4 address settings In addition you can e Activate the DHCP protocol Dynamic Host Configuration Protocol in your local network Please select the check box Use DHCP A After activation of the changed settings the DHCP protocol will automatically assign a new IPv4 address to the RCI10 sub assembly Please make a note of this address if you wish to connect your configuration PC again with the system at a later date without network You then have to enter https lt new IPv4 address gt as URL into the address bar of the web browser lt new IPv4 address gt the above noted address Should you deactivate the check box Enable v4 no IPv4 address will be considered valid any longer i e you do no longer have access to the RCI10 sub assembly via IPv4 You will then always have to indicate an IPv6 address If your network does not support IPv6 we recommend deactivating the check box Enable v6 lf a DNS server Domain Name Server is available in your network please enter the DNS URL under DNS Server In the category MISC you can e enter a name for the ControlPlex Rack system System name indicate a contact person System contact indicate an installation site System location In addition you can determine the time zone Time zone 1 CE winter time 2 CE summer time
40. lowing table lists various information and safety instructions for start up and use of the device Danger Installation and operation of the device This device has to be installed and operated in compliance with the given instructions Failure to comply can lead to injury damage of loads or of the ControlPlex Rack Danger Turn off the supply voltage Before beginning with installation the system has to be disconnected from the mains A cable connection must only be established if the supply voltage is OFF Danger Possible ignition hazard The device must NOT be used in inflammable surroundings Danger High voltage The cover must NEVER be opened Access to the inner components is not allowed unless indicated otherwise in this manual Caution Work with ESD protection Electronic modules must only be touched and installed with ESD protection so as to ensure protection against electrostatic voltage Failure to comply can cause damages on the Contro Plex Rack system or the corresponding components Caution Grounding The device must be grounded before switching on Table 1 Important information EMC Installation Guidelines The ControlPlex Rack hardware and accessories comply with the EMC directives Thus electromagnetic interferences between the devices are avoided which would otherwise affect the system performance A professional installation is mandatory In order to ensure the best EMC conditions the widest possible distanc
41. lt gt 1 O N A R D 37 14 Appendix Example RCI10 configuration file excerpt Excerpt from file exportSettings ini dhcp enablev4 0 enablev6 1 enablev6 0 ipv4addr 192 168 0 25 ipv4gateway ipv4mask 255 255 255 0 ipv6addr 2001 ipv6prefixlen 56 feeda switchbackontemperature switchbackontemperatureen switchbackonvoltage switchbackonvoltageen switchoffcurrent switchoffcurrenten switchofftemperature switchofftemperatureen switchoffvoltage switchoffvoltageen fuse label Server 1 stateafterreset stateafterreseten 0 switchbackonovertemperature switchbackonovertemperatureen switchbackonovervoltage switchbackonovervoltageen switchoffcurrent switchoffcurrenten switchoffovertemperature switchoffovertemperatureen switchoffovervoltage switchoffovervoltageen switchofftime switchofftimeen switchontime switchontimeen http allowfuseswitch 1 allowlogaccess 1 allowsettingswrite 1 authonly 1 httpsonly 1 language de login eta password misc systemcontact systemlocation systemname Control Plex Rack ntp dst 1 enable 1 server ptbtime1 ptb de timezone 1 rack enablefeedmonitoringafterreset 0 snmp allowfuseswitch 1 allowsettingswrite 0 authentication MD5 community private enable 1 enabletraps 1 encryption AES encryptionkey login eta password traptarget kkk ssh kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk
42. ment system Typical application is mainly the control and monitoring of decentralised telecommunication systems Besides this document more information about the E T A ControlPlex Rack can be found in the following documents ControlPlex Rack Data sheet Here you will find more technical data and figures as well as approval information on the various components of the Contro Plex Rack system ControlPlex Rack Installation and operating instructions Here you will find the instructions for installation and start up of the hard ware of the ControlPlex Rack system as well as helpful information for component replacement and trouble shooting on site The latest documents can be found on our website under www e t a de controlplex_rack All documents contain important instructions for connection and safe operation of the ControlPlex Rack system Safety instructions have to be observed All users have to be informed about all safety instructions The documents have to be accessible for the user General note Qualified personnel The system must only be installed connected configured and operated in connection with the above men tioned documentation Installation and operation of the device system must only be carried out by qualified personnel With regard to the safety instructions of this documentation qualified persons are persons au thorised to operate devices systems and circuits according to the standards and rules of saf
43. nagement system The supported SNMP protocol allows control of the ControlPlex Rack System centrally by means of a management system For this purpose the available RCI10 MIB has to be integrated into the management system Advantages include centralised alarm surveillance as well as an automation option by connecting various threshold values also of other systems within the management system A For integration of the ControlPlex Rack SNMP MIB into your management system you possibly require special expert knowledge and the complete documentation of your management system In the event of any questions please feel free to contact the manufacturer of the management system Via the SNMP protocol MIB tree you the following setting options for the network configuration e P address data e SNMP log on data e System time e Settings of the ControlPlex Rack system specific system designations 29 9 1 Operation with management system Settings in the RCI10 sub assembly Before you can integrate the SNMP MIB into your management system the RCI10 SNMP settings have to be configured via the SSH interface according to the requirements of the management system For this purpose you require the following information 1 Which version of the SNMP protocol is supported by the management system v1 v2c v3 2 The IP address of the management system to which the alarm and status messages of the RCI10 sub assembly shall be sent If you use
44. nen 9 5 1 Start up Useful information on the web browser SUrfaCe ccccseccceseeeseeeecaeeeceueesaeeesaueesaneesaaees 9 5 2 Start up IP settings on the configuration PC 2zuzu022200202000nnnonnnnennnne neuen neuen neuen nnnne nenne nenne nnnnenn 10 5 3 Start up Status and installation of the hardware eesaae aaa aaa aaa neuen neuen neuen nnnn nenne nenne nnnnenn 10 5 4 Start up Starting the web browser surface ee aau aaa aaa aaa aaa aaa aaa neuen neuen nnnnnnnnnonnnne nenne nnnnenn 10 5 5 Start up Configuration by means of web browser surface uu2u2u222u0nnnennnennnnnnnne nenn nenn nenne nnnn nennen 12 6 General RCI10 Start up with the SSH v2 surface 22 2002000000nn0nnn0nnnnnnunnnnn nun nun nnnnnnnn nun n nun nnEn nn 13 6 1 SSH tools Installation SSHv2 Client programme LePutty eeeanneeensnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnne nennen 13 6 2 SSH tools Installation SSHv2 Client programme LePutty u uueannnneennnnnennennnnnnnnnnnnnnnnnnnnnnonnnnnenen 13 6 3 Start up Configuration via SSH Surate eseeto anne nnnnnnnnnnnnnnenannen anne nun sauer 14 6 4 Start up Table of SSH configuration parameters and factory SettingS cccccccconnoconnocannnnannnnos 16 6 5 Start up RCI10 configuration file download es aaeeaaae aaa aaa wawa aaa neuen nnnnnnnnnnonnnnennnne nenne nnnnenn 18 6 6 Start up RCI10 configuration by means of configuration file uploads
45. ng overcurrent and short circuit protection it increases system availability by a multiple because it disconnects faulty loads quickly selectively and without voltage dips In connection with the control interface module type RCI10 the ControlPlex Rack system can be connected to a centralised management system control computer For this purpose an Ethernet interface is made available with SNMP v1 v2c or v3 protocol The required private MIB for embedding is part of the delivery scope An additional possibility for a centralised or also local monitoring control is provided by the integral web server which can be used without additional software on the control computer by means of the web browser In addition great importance was attached to system security against illegal access Therefore the configuration of the RCI10 sub assembly is effected via a secure Secure Shell SSH surface It also offers a great number of configuration options to increase system security Thanks to its system properties the ControlPlex Rack is the perfect solution for smart protection control and energy measurement for DC supplied minus switching system cabinets Typical applications include e System cabinets of any kind in telecommunications with DC 48 V or DC 60 V rated supply e Server cabinets in IT centres with equipment for DC 48 V or DC 60 V rated supply e System cabinets for mobile radio and television for DC 40 V to DC 72 V e Protection and control
46. nt ON and OFF operation Enter a threshold value in the corresponding field s 3 Save the settings in the RCI10 sub assembly by clicking the button Save The entered settings will thus be activated If possible test the activated value on the Contro Plex Rack system 5 Repeat steps 1 to 4 for each parameter specific setting A Should you wish to de activate the set values but you do not yet know if you will need them again at a later date you only have to de activate the check box es beside the input field s and save the change s Now all threshold values are de activated but still saved 8 3 Operation with web browser Function of the mask Fuse Settings The mask Fuse Settings offers the possibility to automatically switch on or off one single load output depending on the threshold values The following limit values can be set e Voltage value circuit protector gt automatic ON and OFF e Load current value circuit protector gt automatic OFF A The value should be smaller than the current rating of the circuit protector which would otherwise never switch off e Temperature value circuit protectorr gt automatic ON and OFF e System time of RCI10 sub assemblyr gt automatic ON and OFF e Free time indication seconds gt remote RESET of load power off on 25 Faulty entries may cause inadvertent failure of your system We recommend testing activated threshold values before using them for continuous
47. of illuminated advertising with a power supply of DC 48 V Further descriptions of the ControlPlex Rack systems mounting and connection procedures for the hard ware as well as an instruction for start up and trouble shooting of the individual components can be found in the manual ControlPlex Rack mounting and operation instructions This document contains a configuration and operation instruction for the software of the Remote Control Interface sub assembly RCI10 You will learn more about e How to configure the RCI10 sub assembly via the SSH surface for the first operation and how to adjust it to your requirements e How to use the integral web surface for monitoring and controlling the ControlPlex Rack system e How to embed the ControlPlex Rack system into a management system 2 Minimum requirements for start up of the RCI10 sub assembly Please check if the components of the ControlPlex Rack system were completely installed and work faultlessly see document ControlPlex Rack Installation and operation instructions You require the following tools for configuration and start up e PC with Ethernet interface LAN and operating system Windows 7 x or higher e Pre installed internet browser such as IE from v9 or Mozilla Firefox from v28 8 please also see data sheet ControlPlex Rack e Ethernet cable 10 100 Mbit standard network cable in the required length 3 Important information and safety instructions The fol
48. or OFF via the SNMP protocol Possible values Yes No SNMP community string SNMP community string of the RCI10 sub assembly If the protocol version SNMPv1 or SNMPv2c is used the management system has to know the string indicated here The value entered here is valid for the parameters read and write Permitted characters 20 characters a z A Z 0 9 1 amp _ 2 3 lt gt M Defines the user name user ID for an SNMP v3 connection Permitted characters 20 characters a z 0 9 _ SNMP password Defines the password for an SNMP v3 connection Please observe upper and lower case Permitted characters 20 characters a z A Z 0 9 amp 0 M H _ gt N SNMP authentication SNMPv3 authentication method Possible values MD5 SHA SNMP encryption SNMPv3 encryption method method Possible values AES off DES SNMP encryption key SNMPv3 key used for data encryption Permitted characters ControlPlexRack ESX300 500 characters a z A Z 0 9 amp _ lt gt Table 4 SSH SNMP Settings Allow settings write Parts of the configuration settings such as snmp login IP address etc Yes can be changed directly via SNMP management system Possible values Yes No 30 9 2 Operation with management system Embed SNMP MIB The SNMP MIB file CP RCIxx_SNMP MIB_Vxx mib can be downloaded from our website www e t a de controlplex_rack free of charge For integration of
49. output connected red overvoltage failure U gt 73 V load output disconnected Grey empty slot Overtemperature green temperature of circuit protector lt 100 C red excess temperature failure load output was disconnected reset is only possible after temperature reduction grey empty slot No VCC green supply voltage gt 15 V grey no supply voltage Load out status green load output of circuit protector ON connected grey load output of circuit protector OFF locked out Load out ON OFF When actuating clicking the button the load output of the related circuit protector is switched ON or OFF This is indicated by the LED load output ON green or OFF grey Table 3 Web mask LED colours 8 2 Operation with web browser Function of the mask Feed Settings The mask Feed Settings offers the possibility to completely and automatically switch on or off all load outputs of a feed group depending on the limit value settings The following limit value settings are possible e Voltage value of feed group gt automatic ON and OFF of feed e Load current value of feed group total current automatic OFF of feed e Temperature value of feed group medium value automatic ON and OFF of feed Faulty settings may cause inadvertent failure of your system We recommend testing activated threshold values before using them for continuous duty 24 Example Mask Feed Settings version PDB N CP18R RR x with redundant
50. th the Cursor buttons 1 to the menu option Firmware update and press Enter 4 A submenu opens Start the software upload to the RCI10 sub assembly by pressing the Enter button again 5 Navigate with the mouse on the upper SSH window frame Press the right mouse button a menu opens Select the menu option Zmodem Upload 6 Abrowser window opens Mark the new image file meant for uploading on your configuration PC and click on Open 7 Wait until the upload to the RCI10 has successfully been completed The RCI10 sub assembly automatically carries out a re boot Re boot activates the RCI10 software It can take several minutes until you can access the RCI10 sub assembly again A Please keep in mind that the original factory set configuration was re activated after the software up date 8 Load the configuration file saved in step 1 into the RCI10 sub assembly as described in chapter 6 6 8 General RCI10 operation with web browser The web surface offers a comprehensive use of the ControlPlex Rack system Besides a graphic surface for monitoring and manual switching of the circuit protectors there is a second level for configuring threshold values for automatic ON and OFF operation of the circuit protectors Over a third level the log and measuring data files can be reviewed and saved 8 1 Operation with web browser Function of the mask Fuse Control The mask Fuse Control serves for monitoring the individual electron
51. the RCI10 MIB into the management system please follow the instructions of the manufacturer of the management system amp MIB Tree I d iso org dod internet private enterprises eta etaProp rcil0 a system B Ji smp Je ethernet ol N ipv 4 E ipv6 iu Fag dnsServer 4 dateTime a hwVersion U hwSerial gt swVersion systemName 2 systemContact systemLocation A monitorEnabled reset CI Je fuses j Je feedA be i sumCurrentA 2 fusesATable El fusesAEntry feedB er switchAllFuses E de notifications 2 prefix objects Fig 21 SNMP MIB Tree 31 10 Appendix List of pictures Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig Fig 32 1 Schematic diagrami COMEMOIPIOX Rack in engeren dais 8 2 schematic diagram Gonfro Ple Rack wa aaa a ob O A A Ak ENE 8 SPV Setting COMMOUIAU OM iS zaa AE a iS 10 Ae Web broWser login Esel 11 De Web Mask FUSES nia 11 6 Web mask Gonfiguration System settings ann ek 11 7 P On y HLA RII LePUTTIY O Re A CC lai UZ aid c GOW 13 8 ZModem configuration Cera 14 SSA MAMA AE O OGR C O NAA 15 I0 SEX MOR SETEINGS an nal 18 le SSH Zzmoden pUulldown MOM A aa 19 12 SOrLEXport c iiguratio TIE successful 19 138 SOF System information SUDMENU EGER A A AAA Z AA ZERA GE ERA ER ARTE 21 14 web mask Fuse Control additional information ESX300 S sasaaa eee aaaaaaaaaa anna emama
52. tings in the configuration file RCI10_Config Vxx 6 3 Start up Configuration via SSH surface Before starting configuration you have to check the IPv4 settings on the configuration PC and amend them if required see chapter 5 2 Start up IP settings on the configuration PC 1 Start the programme LePutty and load the saved configuration file RCI10_Config_Vxx as described in chapter 6 2 paragraph 1 2 Click on the button Open in the LePutty window The programme will now build up a connection to the RCI10 sub assembly and open an SSH window 3 Authenticate yourself with User user and password user1234 factory settings You now see the SSH configuration menu 14 ONULIO X Rack COntiguration SSH settings TP settings r Fig 9 SSH main menu A gt The Cursor buttons 1 allow navigation in the menu menu items can be selected with the Enter button Parameters can be changed by the buttons e g Yes No or adjusted by direct entry of the value e g name The F1 buttons helps to leave a submenu and to close the SSH connection in the top menu A list of all SSH configuration parameters with a short description can be found in chapter 6 4 below Please make a note of all configuration changes with the newly entered values For this purpose you can print the table inserted in chapter 13 and enter the values manually After changing configuration settings you have to select
53. version status indication circuit protector F1 via LED colours see table WEB LED colours Load Curent A 003 0 00 000 0 00 main switch all circuit protectors ON OFF Load ou GNI OFTT load c u rrent System name Cantrol Plex Rack System location Altdorf b Nbg SW version 0 991 n d c at on System contact senal number ON OFF switch system information circuit protector F1 Fig 15 Web mask Fuse Control with description 23 The table below gives a description of the colours for the LED status indication on the web surface Field name Status bar LED colour coding of the circuit protectors on the web surface green no short circuit lt of the circuit protector red short circuit failure gt 1 2 x I load output was immediately switched off grey empty slot Overload green no overcurrent lt I of the circuit protector yellow overcurrent failure gt lt 1 2 x I load output ON max 30 sec red overcurrent failure gt lt 1 2 x 1 load was disconnected after approx 30 sec of overcurrent grey empty slot Undervoltage green voltage gt 37 V yellow undervoltage failure U lt 36 V load output connected red undervoltage failure U lt 36 V load output disconnected load output was off upon occurrence of the failure or was disonnected manually automati cally during the failure grey empty slot Overvoltage green voltage lt 72 V yellow overvoltage failure U gt 72 V load
54. x0001 Nominal current 2 A Load current 0 00 A Operating voltage 27 V Temperature 26 C Em 164 01 01 1970 01 00 18 19 System restart after power up Page Down 163 01 01 1970 04 26 59 8238 User configuration started user user SSH connection 192 188 0 20 63034 192 188 0 25 22 162 01 01 1970 04 26 39 8816 Time changed from 1970 01 01T02 28 49 to 1970 01 01T03 20 39 Log Page 181 01 01 1970 03 26 34 8795 User configuration started user root SSH connection 182 188 0 20 62561 192 188 0 25 22 180 01 01 1970 01 02 22 143 User configuration started user user SSH connection 192 168 0 20 62508 192 168 0 25 22 159 01 01 1970 01 02 18 130 User configuration started user user SSH connection 192 168 0 20 62507 192 168 0 25 22 Auto scroll EA 158 01 01 1970 01 02 16 137 User configuration started user user SSH connection 192 168 0 20 62506 192 168 0 25 22 gt 157 01 01 1970 01 02 05 126 User configuration started user user SSH connection 192 168 0 20 62505 192 168 0 25 22 156 01 01 1970 01 02 01 122 User configuration started user user SSH connection 192 168 0 20 62504 192 168 0 25 22 155 01 01 1970 01 01 59 120 User configuration started user user SSH connection 192 168 0 20 62503 192 168 0 25 22 152 01 01 1970 01 08 44 525 User configuration started user user SSH connection 192 168 0 20 62467 192 168 0 25 22 151 01 01 1970 01 08 40 521 User configuration started user user SSH connection 192 1
55. y a management system Possible values Yes No SNMP protocol Determination of the permitted SNMP protocol The RCI10 supports SNMP v1 v2 v3 Data are transmitted encrypted only with v3 Possible values v1 v2 v3 Enable traps Permit the sending of SNMP traps If in the ON condition alarm message can immediately be reported without a query from the superordinate system management system Possible values Yes No Trap target The IP address or the host name of the system to which the SNMP traps alarm or status indication shall be sent When entering more than one address they have to be separated by a semicolon Allow fuse switch Determines if the circuit protectors may be switched ON or OFF via the SNMP protocol Possible values Yes No Value Allow settings write Parts of the configuration settings such as snmp login IP address etc can be changed directly via SNMP management system Possible values Yes No SNMP community string SNMP community string of the RCI10 sub assembly If the protocol version SNMPv1 or SNMPv2c is used the management system has to know the string indicated here The value entered here is valid for the parameters read and write Permitted characters 20 characters a z A Z 0 9 1 amp _ 2 3 lt gt M 3 al Defines the user name user ID for an SNMP v3 connection Permitted characters 20 characters a z 0 9 _ SNMP password
56. y default will disappear Possible values Yes No System name Freely selectable system name Permitted characters 100 characters a z A Z 0 9 15 8 2 4 _ lt gt W1 Allow reset to factory defaults System contact Freely selectable system contact name e g person to contact on site Permitted characters 100 characters a z A Z 0 9 8 amp System location Freely selectable system location Permitted characters 100 characters a z A Z 0 9 15 8 2 H _ lt gt N Ses Time Date settings Description Setting parameters Enter present time if no NTP server see NTP settings was indicated or is available The parameter NTP enable has to be no for that Format Time hh mm ss Enter present date if no NTP server see NTP settings was indicated or is available The parameter NTP enable has to be no for that Format DD MM YYYY Time zone Adjust time zone time difference between local time and UTC Possible values 12 1 0 1 12 Example 1 Central European winter time 2 Central European summer time Calculate with summer time and winter time Possible values Yes No Fuse Labels settings Description Setting parameters Label for fuse Freely selectable system name for the circuit protector ESX300 S in the slot A1 A20 A1 A10 and B1 B10 Permitted characters 20 characters a z A Z 0 9 amp _

Download Pdf Manuals

image

Related Search

Related Contents

Getting Started with iFIX - GE Intelligent Platforms: Support Home  TRD-HU9816    USER MANUAL - Tanning Bed Parts  PCI8522 User`s Manual  KSB202 Projektierungshandbuch  Sierra 830 Marine Sanitation System User Manual    ペディアサット・オキシメトリーカテーテル - Edwards Lifesciences  取扱説明書 スロープ台 樹脂製 乗用車用 3ton 品番:#54510500  

Copyright © All rights reserved.
Failed to retrieve file