SA 2500 Kit User Manual
Contents
1. User PIN Code 1 is set as 1234 and also used by the app to send SMS command by default When you change SMS Keyword or User PIN Code 1 and save the setting The SMS Keyword and PIN Code stored in Panel Information will also be updated accordingly Please make sure the Control Panel successfully receives the SMS command If the panel fails to receive the SMS command you need to edit the Panel Information manually to change SMS Keyword or PIN code back to previous setting Otherwise you will no longer be able to control the panel with the app You can delete the User PIN code by keeping the PIN Code field blank and save the setting User PIN Code 1 cannot be deleted Press the Menu button on your Android Alarm Setting phone to bring up the Sync function Press Sync to send a SMS command to the The Alarm Setting Menu allows you to edit Control Panel for inquiring current User PIN alarm related configuration code setting Once your phone receives the SMS response message from the Control Alarm Settings Panel Connect2Home app will update the User PIN code information Exit Delay Timer 30 secs If this PIN code is the PIN code used to send SMS to the Control Panel do not change the code Otherwise the Control Panel will not be able to receive your SMS message To change the PIN code used to send SMS commands you need to delete this panel and add a new panel with the new PIN code Exit Delay Volum2. If the system is not disarmed before the timer expires an alarm will be activated 3 When a device previously set to Home Omit is triggered in Home Arm mode the device will be ignored If the device is triggered in Away arm mode the alarm will be activated immediately 4 When the tamper switch of the devices is triggered in Away arm mode the alarm will be activated immediately 5 You can trigger an Emergency alarm with the Remote Controller Stopping the Alarm During an alarm the Control Panel will sound the siren and report to the programmed telephone numbers To stop the alarm send a SMS command to disarm the system with Connect2Home application or press the Disarm key on your Remote Controller NOTE Remote Controller cannot be used to stop the Emergercy Alarm triggered by itself 33 Alarm Memory lf an alarm was raised without being silenced during your absence the alarm reporting will still be carried out When you come back and disarm the system the siren will sound for 3 second to warn you that the intruder might still be inside your house Tamper Protection 1 When the system is under Away Arm mode if a tamper switch is triggered an alarm will be activated immediately The Control Panel will send a SMS alarm event Tamper to programmed SMS report telephone number or dial the Voice report telephone number and play Burglar message upon answer 2 When the system is under Home or Disar
3. 2 Device Setting The Device Setting Menu allows you to edit device Control Siren Optional Siren Device required and learn in or control Power Switch Optional Power Switch required Device Settings Edit Device Zone Attribute Burglar Name device A Select the top column to choose between Edit Device Siren Control and PSS Control 5 Device Settings Edit Device Edit Device Siren Control PSS Control Capture Image Device Type Unknown Delete This Device SA2500 Control Panel does not support Capture Image function please skip this option Edit Device The Edit Device option allows you to edit a device name and attribute for Door Contact PIR and EIR Sensor Device Settings Edit Device Zone Attribute Burglar device A Name Unknown Device Type Delete This Device Select the Zone number of the device you want to edit and enter a new name For Door Contact and PIR Sensor please select an attribute For other devices without attribute you can select any attribute as it will not affect the device setting Press Save The phone will send a SMS command to panel You can also remove the device specified by pressing Delete This Device 28 You can press the Menu button on your Android phone to bring up the Sync options and choose to sync device information in different zones Zone Attribute Burglar N S
4. Entry Exit Time and Device Attribute When the system is armed and an Entry device is triggered the Entry timer will begin to count down default 20 seconds The system must be disarmed before the timer expires or a Burglar alarm will be activated When the arming process is initiated the Exit timer will begin to count down default 30 seconds the system will ignore any sensors triggered during this period The user should use this duration to leave the premises before the system is armed NOTE PIR Sensor and Door Contact learny in will be automatically assigned to Entry attribute For device attribute setting and Entry Exit Time programming please see later chapter 5 Connect2Home Application Alarm Activation When an alarm is triggered the system will report to the programmed telephone numbers according to the priority The system can dial the telephone numbers you entered in the system play voice message upon connection or send an SMS message Address Message The Address Message will be played in the beginning of all your voice message reports to notify the recipient of your user information Please make sure you have recorded your own Address Message by referring to the previous chapter 3 Getting Started Alarm Length Default alarm length for siren upon activation is set to 3 minutes To change the alarm length please refer to chapter 5 Connect2Home Application Jamming and Interference Detection The
5. mark the position of the holes on the wall at chest height 2 Drill two holes into the wall fix the mounting plate on the wall with screw and plugs provided 3 Hook the Control Panel onto the plate Mounting Holes PIR Sensor The PIR Sensor has knockouts on the back where plastic is thinner The 2 center knockouts are for flat wall mounting and the 4 side knockouts are for corner mounting 1 Break through the knockouts use the knockouts to mark position on the wall or corner 2 Drill holes into the wall or corner using the knockouts as template 3 Fix the PIR Sensor base onto the wall with the screws and plugs provided 4 Replace the PIR Sensor cover onto the base Corner Fixing O MIOCKOUIS X 4 Surface Fixing Knockouts x 2 Inside Door Contact The Door Contact has 2 knockouts on the inside of the back cover where plastic is thinner for wall mounting 1 The Door Contact should be mounted on the door window frame while the magnet should be mounted on the door window as shown in the picture below The gap between the Door Contact and the magnet should be no more than 15 mm 2 Drill holes into the wall using the knockouts as template then fix the Door Contact base onto the wall with the screws and plugs provided Alternatively you can also use the double side adhesive tape provided to glue the Door Contact on the frame 3 Replace the Door Contact cover onto the base 4 System Default Setting
6. 0 or 9 key on his telephone set Press 1 v The Control Panel will open a one way listen only channel for 2 minutes for you to listen to what is happening on the other side v During the last 20 seconds of the 2 minute period the Control Panel will sound a beep to remind the recipient Press 1 again to extend another 2 minutes v When the 2 minute period expires the Control Panel will automatically hang up and dial the next number 34 Press 0 v The Control Panel will hang up v The Control Panel will continue Alarming v The Control Panel will dial the next number Press 9 v The Control Panel will hang up v The Control Panel will stop alarming and stop dialing The panel will also stop reporting if 2 call recipient press 1 or 0 to acknowledge the report lf the call recipient hangs up the telephone without any acknowledgement the Control Panel will redial the telephone to retry the report for a maximum of 5 times Auto Redial When only one telephone number is stored and the number is engaged the Control Panel will automatically redial up to 5 times with an interval of 80 sec between each attempt When more than one telephone numbers are stored the Control Panel will dial according to priority order If the number being dialed is engaged it will try the next number Each number will be tried up to 5 times and the interval between each attempt is 20 sec The Control Panel will redial the telephone numbers for
7. 2 or higher for Android phone 11 Connect2Home for iPhone panel name you want to use in the application panel SIM card phonenumber The iPhone version of Connect2Home a User PIN Code and the SMS keyword Application supports all SMS command used to access the panel Press Done to functions except SMS commands which inquire confirm when finished Control Panel for information This is due to the limit of iOS system which prohibits incoming SMS message from accessing application data Cancel New Panel An iOS version of 6 1 or higher is required to use Connect2Home Application on iPhone Panel Name Select the Connect2Home icon to start the Panel SIM application PIN Code SMS Keyword Conn Home You will return to Panel Selection menu the new panel you entered will be displayed Add New Panel Upon starting the application you will first enter Panel Selection menu My Panel Remove My Panels Remove My Panels The PIN Code and SMS Keyword entered in Panel Information are included in every SMS command sent with the app for the Control Panel to verify the SMS command The default SMS Keyword is PROG The PIN code must be identical to a User PIN Code in the panel The factory default PIN code in the Control panel is 1234 for User PIN Code 1 You can change both SMS Keyword For first time user you need to first enter and PIN code later by editing panel 66 77 your panel in
8. Control Panel is capable of detecting signal jamming and interference the function is disabled by default if jamming and interference is of concern to you please see chapter 5 Connect2Home Application 10 5 Connect2Home Application The application is designed to help you to easily control and program your system remotely using a smartphone Featuring an intuitive and simple interface it is easy to recognize and operate IMPORTANT NOTE 1 After you send a SMS message to the Control Panel please make sure you receive a confirmation message from the Control Panel If you receive an error message or no message at all it means the command was unsuccessful Please resend the message or change the setting back to avoid discrepancy betweeen the application and Control Panel 2 Connect2Home application controls your Control Panel by sending SMS command messages Please be reminded that each SMS message sent will incur extra cost Connect2Home application supports complete system programming and control function It also features remote Power Switch control and Home Automation rules for easy energy management To use the application please go to iPhone App Store or Google Play Search for Connect2Home for the application download and start the application The application is only compatible with iPhone or Android phone it does not support iPad or Android tablet computer System Requirement IOS 4 3 or higher for iPhone Android 2
9. Indoor Siren can be enabled or disabled from sounding warning beeps during Entry Time and Exit Time When set to Enabled the Siren will beep during Entry and Exit Time When set to Disabled the Siren will not beep during Entry and Exit Time Learn Repeater Optional required Use this function to send add the Repeater device into your alarm system Put your repeater into learning mode the send the SMS command to the Control Panel The panel will transmit signal to Repeater upon receiving the SMS command Please refer to Repeater manual for further detail Repeater PSS Control Optional Power Switch required The Power Switches can be controlled manually or through Home Automation settings to turn on off you home appliance remotely to monitor your home environments Device Settings PSS Control PSS Channel Action On Off Learning PSS Learning Put the Power Switch into Learning mode Please refer to Power Switch manual for detail Select Learning in the Action option on your Connect2Home application Press Save to send the SMS command to panel The control panel will transmit signal to the power switch The power switch LED will flash 3 times upon receiving signal from Control panel to indicate learning is now complete PSS Control Select the channel you want to edit then choose to turn on off the Power Switch Press Save to send the SMS command to
10. Panel will emit 1 beep and the Mode LED will stop flashing and stay lit to indicate it is now under Disarm mode 5 When you try to learn in a device that was previously learned into the system the Control Panel will emit a Ding Dong sound NOTE The Learning Mode will time out after 5 minutes However whenever the Control Panel receives a learn code the 5 minutes timer will be reset Device Mounting After learning devices you should proceed to mount the devices in select locations in your home As you mount the device you also need to test the device signal range to make sure the device is within control panel operation range See below for instruction on device range test and individual device mounting guideline 1 Put the Control Panel into Learning mode by pressing the Function button once 2 Find a location where a device is to be mounted put the device at the location and press learn test button on the device refer to each device manual for detail 3 If the device is within range of the Control Panel the Control Panel will emit a Ding Dong sound to indicate the device is wirelessly connected to the Control Panel When you are certain the device can function properly at the chosen location proceed to mount the device 4 When mounting devices make sure the device tamper is fully depressed please refer to device manual for tamper location Control Panel 1 Use the two holes on the Wall Mounting Plate
11. Pressing Back button on your Android phone will return to Panel Selection Menu My Panel EDIT DELETE AN N a o Arm Home Disarm 4 PIN Settings Alarm Settings RS Reporting Settings a Device Settings Home Automation Settings Delete Panel o remove current panel select the Delete button at the top right of Panel Main Screen You will be asked to confirm the action select OK to delete the panel You will return to Panel Selection Menu My Panel EDIT DELETE AN N AN Arm Home Disarm Edit Panel Information You can edit the Control Panel information by pressing Edit My Panel EDIT DELETE AN N AN Arm Home Disarm Enter the new panel name panel SIM card number and PIN Code and the SMS keyword you desired Press Save to confirm when finished Edit Panel Panel Name My Panel Panel SIM 123456789 PIN Code 1234 SMS Keyword PROG Away Arm Home Arm Disarm To change system mode Press the Arm Home Disarm buttons The phone will send a SMS command to panel to execute the command Sync with Panel Press the Menu button on you Android phone to bring up the Sync option Press Sync to send an SMS command to Control Panel requesting it to report back its current mode Once your phone receives the SMS response message from the Control Panel Vesta EZ Home app will update the current system mode accordin
12. card base by sliding the cover toward LOCK direction Powering On 1 Plug the AC adapter into power socket and connect the other end to the DC Jack 2 Switch On the Battery Switch to charge the battery and prevent accidental power shortage 3 The LEDs will light up briefly to indicate powering on LED Indicators The LED indicators represent the status of control panel 1 Power LED Green LED On AC Power connected Green LED Flash AC Power failure 2 Mode LED Red LED On The Control Panel is in Away Arm mode Red LED Flash The Control Panel is in Home Arm mode Green LED On The Control Panel is in Disarm mode Green LED Flash The Control Panel is in Learning mode 3 Fault LED Yellow LED On There is at least one fault in the Control Panel Yellow LED Flash There is at least one fault in the devices 4 GSM LED On for 5 seconds when power is supplied Flash slowly GSM normal Flash quickly GSM failure Record Address Message The Control Panel is capable of reporting events through SMS message or Voice message When Voice Reporting is selected and an alarm is triggered the Control Panel will dial the programmed telephone number and play the alarm message upon answer The Address Message is the first voice message played at the beginning of every voice message report to notify the call recipient of the caller s information The default Address Message is Alarm System You can record your own Address Message through the follo
13. effective when the intruder is moving across its field of view Do not mount PIR sensor in a location that faces intruder directly Do not mount the PIR sensor to look at door window protect by Door Contact as the signal transmitted simutaneously from PIR and Door Contact could cancel each other Do not mount the PIR sensor directly exposed to sunlight Do not point PIR sensor at window or sources of heat e g fire or boiler Door Contact The Door Contact should be mounted as high as possible Do not aim a PIR sensor at this door window Remote Controller lt is used inside or outside your home and can be kept on the keyring Control Panel The Control Panel should be mounted in a hidden area and invisible however still accessible The Control Panel should be mounted at a location with good GSM strength to send report and receive command 2 Device Introduction The Alarm System supports multiple devices which are listed in this section For accessory devices please refer to individual device manual for detail instruction NOTE The basic package you purchase includes the following devices 1 x PIR Sensor 1 x Door Contact 1 Remote Controller Other useful devices are available separately see www blaupunkt com Power Mode Fault GSM LED LED LED LED Microphone Mounting Holes DC Jack D sattery Bi Function Buzzer Control Panel GSM Module A9QV 1A adaptor is su
14. panel 30 Home Automation Rules Power Switch required Optional 1 With Home Automation rules you can program the Power Switches to turn on off for preset duration under different conditions This function allows you to control your home environment when away 2 The following conditions are available for settings Arm When the system is Away Armed Home When the system is Home Armed Disarm When the system is Disarmed High Temperature When the temperature is higher than the pre set threshold Low Temperature When the temperature is lower than the pre set threshold Alarm Event When the set alarm event is triggered When any of the required conditions are met the Control Panel will execute the set rules accordingly SAVE Home Automation Settings If panel is set to Arm If panel is set to Arm If panel is set to Home If panel is set to Disarm If temperature is greater than If temperature is less than If current time is If an alarm event occurs 1 Select the condition in the top column Select to enable disable the rule Select the Power Switch channel to be controlled Choose to turn on or off the Power Switch Select the duration of on off status For High Low Temperature condition set the temperature threshold for the Power Switch to be activated deactivated For Time condition set the time when the Power Switch should be activated deactivated F
15. up to 3 cycles 15 times maximum 35 7 Troubleshooting amp Factory Reset This chapter covers the potential issues you may encounter during system operation Control Panel Control Panel Fault Yellow LED indicates fault in system If the fault happens in the Control Panel the LED stays lit If the fault happens in the devices the LED flashes The possible fault events include Control Panel Devices low battery Change device batteries or charge Control Panel battery accordingly AC power fail Check AC power connection sensor out of order Check device battery status and conduct Walk Test to confirm if the Control Panel can receive device signal Device tamper Close the device s tamper switch GSM related failures lf the GSM LED flashes quickly that means there is a fault in the GSM functions Check if SIM card is properly installed Check if SIM card s PIN is inactive Check if the signal strength is strong enough Interference Perform Walk Test on all your devices to check if Control Panel can still receive their signals Use Test Call function to test if Control Panel can report normally to programmed telephone number PIR Sensor PIR LED flashing when activated PIR is on low battery or tamper switch triggered PIR is not responding to movement PIR has a built in 1 minute sleep timer after detecting a movement PIR will not redetect movement within 1 minute afte
16. IM cards have a validity period and must be extended before they expires some SIM cards will expire automatically if they are not used for a certain time period When using prepaid SIM card please make sure you fully understand its user policy and check the SIM card s remaining value regularly with your service provider to make sure the SIM card is functioning normally 3 PIR Sensor The PIR sensor detects movement and raise alarm when it detects an intruder The PIR sensor is powered by a 3V lithium battery pre inserted by factory Pull out the plastic battery saver tab on the back of PIR sensor this will activate the batteries The LED will flash for 30 seconds to indicated the PIR is warming up When the battery voltage runs low please follow instruction below to change batteries 1 Remove the screw at bottom of PIR sensor to open the cover 2 Remove the old battery and press the learn button a couple times to discharge 3 Insert the new battery and replace the cover LED Indicator Learn Test Button Door Contact The Door Contact detects door window opening and notifies the Control Panel to raise alarm The Door Contact is powered by a 8V lithium battery pre inserted by factory Pull out the plastic battery saver tab on the back of Door Contact This will activate the batteries Press the learn button to transmit learn code When the battery voltage runs low please follow instruction below to change batteries 1
17. Remove the screw at bottom of Door Contact to open the cover 2 Remove the old battery and press the learn button a couple times to discharge 3 Insert the new battery and replace the cover LED Indicator Magnet D Learn Test Button Remote Controller You can arm home disarm and activate an Emergency alarm with your Remote Controller For disarming action you can only use Remote Controller to disarm the system after you have triggered an entry Door Contact or PIR sensor The Remote Controller is powered by a CR2032 3V lithium coin cell which is included in the package Open the back battery cover to insert the battery then replace the cover When the battery voltage runs low slide open the battery cover to change new battery Arm Button Disarm Button Home Button _ 7 E Emergency Button Battery Cover 3 Getting Started This chapter will guide you through the general setup of your alarm system For System setup please refer to chapter Connect2Home Application Inserting your GSM SIM card Before powering on your Control Panel you need to insert your GSM SIM card NOTE Before inserting the SIM card make sure your SIM card password is disabled 1 Unlock the SIM card base by sliding the cover toward OPEN direction 2 Spring open the SIM card slot and insert your SIM card 3 Replace the SIM slot onto the base lightly 4 Remember to lock the SIM
18. SA 2500 Kit User Manual BLAUPUNKT Table of Contents 1 System Installation Planning 1 2 Device Introduction 3 3 Getting Started 6 4 System Default Setting 10 5 Connect2Home Application 11 6 System Information and Operation 32 7 Troubleshooting 36 8 Specifications 38 Information and illustrations are subject to change within this document Blaupunkt reserves the right to alter the specification and product design at anytime without notice 1 System Installation Planning Away arm and Home Mode Planning The alam system supports two arming modes Away arm and Home Away arm mode will arm all accessory devices installed in the system to raise alarm when activated Home Arm mode will partial arm the system so that no intruder could get inside the premises withought triggering an alarm yet the user can move within the house freely Plan your device location in advance by determining which area should remain unarmed in Home Arm mode and decide which sensor should still be operating in Home Arm mode For more information please see 5 Connect2Home Application Device Operating Range All devices in the alarm system has an approximate range of 30 meters in typical domestic environment The range may vary depending on different home condition When installing devices make sure the device range is tested before mounting the device Tamper Protection Your accessory devices are protected from sabotage attempt by
19. Volume Entry Delay Timer Entry Delay Volume Alarm Length Door Chime Volume Jamming Function High Temperature Alarm Low Temperature Alarm Please refer to below for the configurable settings Exit time Time period given after initiating the arming process During this time no sensors will trigger the alarm and you can exit the premises before the system enters arm mode Default exit time is 30 seconds Exit sound Exit time countdown beep volume Default exit sound is Low Entry time Time period given after triggering a device set with Entry attribute During this time the system will need to be disarmed or the alarm will be activated Default Entry time is 20 seconds Entry sound Entry time countdown beep volume Default entry sound is Low Alarm length The time for the alarm to be activated for Default alarm length is 3 minutes 180 seconds Door Chime Volume The Door Chime sound activated by the Control Panel when a device set with entry attribute is triggered under Disarm mode Default door chime is Disable 16 Jamming function Signal interference detection feature When RF signal jamming interference is detected for a continuous 30 seconds the alarm will be activated Factory Default is Disable High Temperature alarm Optional Temperature Sensor required When enabled if the temperature exceeds this threshold by 1 C a SMS alarm report will be sent to programmed telephone number Wh
20. a tamper switch which is triggered when the device is removed from mounted surface or its cover opened When the tamper switch is triggered the alarm system will be activated to inform you To make sure the tamper switch functions properly please make sure the switch is fully depressed against the mounting surface when installing your accessory devices System Extension Aside from the devices included in the package you can further improve the capability of your alarm system by purchasing extra accessories Including extra PIR Sensor or Door Contract to extend your protection area Remote Keypad for a secondary system operation platform Smoke Detector for fire protection Temperature Sensor for High Low Temperature report and Power Switch for energy management and Home Automation For more information please see 5 Connect2Home Application General Device Location Guideline Avoid mounting the Control Panel and devices close to large metal objects or electrical interference source such as fridges and microwave ovens as they could affect signal strength For devices that has tamper protection function mount on even surface to ensure the tamper is fully closed when mounted For uneven surface use extra packing material on the back Device Location Panning PIR Sensor Mount the PIR sensor at 1 9 2m height for best performance When mounted at 2m height the PIR sensor has a range of 12m PIR sensor detection is most
21. ate appllication data with latest setting information An Android version of 2 2 or higher is required to use Connect2Home on your Andriod phone Select the Connect2Home icon to start the application CU ALIEN Y Connect Fo DE Add New Panel For first time user you need to first enter your panel information please select the ADD button My Panels 22 Enter the panel information including the panel name you want to use in the application panel SIM card number the PIN Code and SMS keyword used to access the panel Press Save to confirm when finished New Panel Panel Name Office Panel Panel SIM 886 12345 PIN Code 1234 SMS Keyword PROG You will return to Panel Selection menu the new panel you entered will be displayed Select the panel name to enter panel menu ft My Panels EAU My Panel The PIN Code and SMS Keyword entered in Panel Information are included in every SMS command sent with the app for the Control Panel to verify the SMS command The default SMS Keyword is PROG The PIN code must be identical to a User PIN Code in the panel The factory default PIN code in the Control panel is 1234 for User PIN Code 1 You can change both SMS Keyword and PIN code later by editing panel information Panel Main Menu The Panel Main Menu is displayed as below You can select different settings to further program different functions
22. disabled If panel is set to Disarm Rule disabled lf temperature is greater than 50 C Rule disabled If temperature is less than 5 C Select the condition in the top column Select to enable disable the rule Select the Power Switch channel to be controlled Choose to turn on or off the Power Switch Select the duration of on off status For High Low Temperature condition set the temperature threshold for the Power Switch to be activated deactivated For Time condition set the time when the Power Switch should be activated deactivated For Alarm Event condition set the events for the Power Switch to be activated deactivated you can set more than one events Press Save The phone will send a SMS command to panel to program the Home Automation setting Back HA Rule Enable Rule PSS Channel Switch Duration Always Alarm lt NOTE gt For system mode change Arm Home Disarm the Power Switch channel selection is limited to 1 only For High Low Temperature and Time setting You can select any Power Switch channel from 1 4 High Low temperature setting in Home Automation does not affect High Low temperature report setting Time condition is disabled for SA2500 Please ignore this function Connect2Home for Android The Android version of Connect2Home Application supports complete SMS command functions including the commands to inquire Control Panel setting and upd
23. e low Entry Delay Timer 20 secs Entry Delay Volume low Alarm Length 3 mins Door Chime Volume disabled Jamming Function disabled High Temperature Alarm disabled Low Temperature Alarm disabled Please refer to below for the configurable settings Exit time Time period given after initiating the arming process During this time no sensors will trigger the alarm and you can exit the premises before the system enters arm mode Default exit time is 30 seconds Exit sound Exit time countdown beep volume Default exit sound is Low Entry time Time period given after triggering a device set with Entry attribute During this time the system will need to be disarmed or the alarm will be activated Default Entry time is 20 seconds Entry sound Entry time countdown beep sound Default entry sound is Low Alarm length The time for the alarm to be activated for Default alarm length is 3 minutes 180 seconds Door Chime Volume The Door Chime sound activated by the Control Panel when a device set with eniry attribute is triggered under Disarm mode Default is Disabled 29 Jamming function Signal interference detection feature When RF signal jamming interference is detected for a continuous 30 seconds the alarm will be activated This feature is Disabled as a factory default High Temperature alarm When the temperature exceeds this threshold by 1 C a SMS report will be sent to programm
24. ed telephone number When the temperature drops to 3 C below the threshold a SMS report will be sent to the programmed telephone number s to notify the recipient of High Temperature Restoration Low Temperature alarm When the temperature drops below this threshold by 1 C a SMS report will be sent to programmed telephone number When the temperature returns to 3 C above the threshold a SMS report will be sent to the programmed telephone number s to notify the recipient of Low Temperature Restoration NOTE You must first learn in an optional temperature sensor to use the temperature report function You can also choose to enable or disable the reporting function If reporting is disabled the system will not send out a report Select the option you wish to edit When you are satisfied with all of your alarm settings press Save The phone will send a SMS command to panel You can press the Menu button on your Android phone to bring up the Sync options and choose to sync either the configurations or high low temperature setting Jamming Function disabled 4 ad Hig Sync Configuration 4 Sync High Low Temperature 4 Reporting Setting The Report Setting Menu allows you to edit your telephone numbers for reporting The SA2500 Kit can program up to 6 telephone numbers for status or alarm reporting The telephone numbers can either be voice reporting or SMS report
25. en the temperature drops to 3 C below the threshold a SMS report will be sent to the programmed telephone number to notify the recipient of High Temperature Restoration Low Temperature alarm Optional Temperature Sensor required When enabled the temperature drops below this threshold by 1 C a SMS alarm report will be sent to programmed telephone number When the temperature returns to 3 C above the threshold a SMS report will be sent to the programmed telephone number to notify the recipient of Low Temperature Restoration Select the option you want to edit you will enter the edit screen lt Back Exit Delay Timer Current setting 30 Slide the screen to select the value you want to change press Alarm Setting to return to menu when done When you are satisfied with all of your alarm settings press Save A SMS message edit screen will appear for you to confirm Press Send to send the SMS command to panel Reporting Setting The Report Setting Menu allows you to edit your telephone numbers for reporting The control panel can program up to 6 telephone numbers for status or alarm reporting The telephone numbers can either be voice reporting or SMS reporting Voice reporting The control panel will dial the number assigned to voice reporting to report an alarm SMS reporting The control panel will send a SMS message to the number assigned to SMS reporting SMS repor
26. formation please select the information ICON Enter the panel information including the 12 Delete Panel Then press Delete the panel will be e a removed from the application To delete existing panel press Remove The screen will show My Panels My Panels Delete My Panel Press the button 13 Panel Main Menu Press the panel name to enter Panel Main Menu Remove My Panels JE My Panel You can select different settings to further program different functions Pressing My Panels button on top left to return to Panel Selection Menu lt My Panels My Panel rm rm ao ff o Arm Home Disarm PIN Settings Alarm Settings Reporting Settings Device Settings Home Automation Settings Edit Panel Information You can edit your control panel information by pressing Edit My Panels My Panel fi Home A m Disarm l w Arm Enter the new panel name panel SIM card phonenumber and PIN Code and the SMS keyword you desired Press Done to confirm when finished Edit Panel Cancel Panel Name My Panel Panel SIM 1234567890 PIN Code 1234 PROG SMS Keyword Away Arm Home Arm Disarm To change system mode select the icon for Arm Home Disarm respectively A SMS message edit screen will appear for you to confirm Press Send to send the SMS command to panel lt My Panels My Pane
27. gly for you to view Please remember to sync your Vesta EZ Home app with all your panel setting when you first create the panel My Panel EDIT DELETE o ag Arm Home Disarm 4 PIN Settings tht Alarm Settings m Reporting Settings OD Device Settings Home Automation Settings PIN Setting The PIN Setting Menu allows you to edit User PIN Codes and SMS Keyword PIN Settings PIN User 1 User Name user PIN Code 1234 If this PIN code is the PIN code used to send SMS to the Control Panel do not change the code Otherwise the Control Panel will not be able to receive your SMS message To change the PIN code used to send SMS commands you need to delete this panel and add a new panel with the new PIN code Select the top column to choose the setting you want to edit PIN Settings PIN User 1 PIN User 1 PIN User 2 PIN User 3 PIN User 4 SMS Keyword and add a new panel with the new PIN code Select the information you want to edit enter the information and press Save The phone will send a SMS command to panel 24 PIN Settings PIN User 1 User Name user PIN Code 1234 If this PIN code is the PIN code used to send SMS to the Control Panel do not change the code Otherwise the Control Panel will not be able to receive your SMS message To change the PIN code used to send SMS commands you need to delete this panel and add a new panel with the new PIN code lt NOTE gt
28. h manual for detail 2 Select Learning in the Action option on your Connect2Home application Press Save to confirm Press Send to send the SMS command to panel 3 The control panel will transmit signal to the power switch The power switch LED will flash 3 times upon receiving signal from Control Panel to indicate learning is now complete PSS Control Select the channel you want to edit then choose to turn on off the Power Switch Press Save A SMS message edit screen will appear for you to confirm Press Send to send the SMS command to panel Home Automation Rules Optional Power Switch required 1 With Home Automation rules you can program the Power Switches to turn on off for preset duration under different conditions This function allows you to control your home environment when away 2 The following conditions are available for settings Arm When the system is Away Armed Home When the system is Home Armed Disarm When the system is Disarmed High Temperature When the temperature is higher than the pre set threshold Low Temperature When the temperature is lower than the pre set threshold Alarm Event When the set alarm event is triggered When any of the required conditions are met the Control Panel will execute the set rules accordingly lt My Panel HA Settings If panel is set to Arm Rule disabled If panel is set to Home Rule
29. ing af hl Sl 11 04am Reporting Settings SAVE Reporting 1 Phone Number 886 123456 Type Events Voice reporting The control panel will dial the number assigned to voice reporting to report an alarm SMS reporting The control panel will send a SMS message to the number assigned to SMS reporting SMS reporting are separated into three types Alarm Status All Alarm if there is an alarm event the control panel will send the alarm information to the programmed phone number Status If there is a status change from Arm to Home Arm etc the control panel will send the status change information to the programmed phone number All The control panel will send report to the programmed phone number for both alarm and status report Select the top column to select the reporting priority you want to edit Reporting Settings Reporting 1 Reporting 1 Reporting 2 Reporting 3 Reporting 4 Reporting 5 Reporting 6 Enter the telephone number for reporting and select report type and events Press Save The phone will send a SMS message to panel NOTE You can delete the telephone number by keeping the telephone number field blank and save the setting You can press the Menu button on your Android phone to bring up the Sync options and choose to sync either Reporting 1 3 or 4 6 vents Sync Reporting 1 3 Sync Reporting 4 6
30. l PIN Setting The PIN Setting Menu allows you to edit User PIN Codes and SMS Keyword lt My Panel PIN Settings PIN User 1 PIN User 2 PIN User 3 PIN User 4 SMS Keyword Select the information you want to edit enter the information and press Save A SMS message edit screen will appear for you to confirm Press Send to send the SMS command to panel Back Edit Pin User Data User Name PIN Code User PIN Code 1 is also used as SMS PIN Code Changing User PIN Code 1 will also change the PIN Code used to send SMS command shown in Edit Panel 15 lt NOTE gt ca User PIN Code 1 is set as 1234 and also used by the app to send SMS command by default When you change SMS Keyword or User PIN Code 1 and save the setting the SMS Keyword and PIN Code stored in Panel Information will also be updated accordingly Please make sure the Control Panel successfully receives the SMS command If the panel fails to receive the SMS command you need to edit the Panel Information manually to change SMS Keyword or PIN code back to previous setting Otherwise you will no longer be able to control the panel with the app You can delete the User PIN code by keeping the PIN Code field blank and save the setting User PIN Code 1 cannot be deleted Alarm Setting The Alarm Setting Menu allows you to edit alarm related configuration Back Save Alarm Settings Exit Delay Timer Exit Delay
31. m mode the alarm will not be activated The Control Panel will send a SMS status event Tamper to programmed SMS report telephone number it will not dial for Voice report The fault LED will light up to remind you Dialing and Call Acknowledgement When an alarm is activated the Control Panel will dial the programmed telephone numbers in priority order for Voice Message or SMS Message report When the Control Panel makes Voice Message Reports After dialing the Control Panel will delay 5 seconds before playing the message It will first play the general part of the recorded message Address then plays the specific alarm message Burglar Fire Medical or Emergency depending on the nature of the alarm To ensure the call is successfully received by the recipient the recipient should acknowledge the message by pressing the appropriate button on his telephone set lf the Control Panel does not receive any acknowledgement the message will be repeated for 85 seconds The Control Panel will then consider the call unsuccessful and dial the next phone number in priority f more than one number is programmed the Control Panel will continue to dial the number s until a recipient presses the third response key f no phone number is programmed the Control Panel will not dial Call Acknowledgement When the Control Panel makes Voice Report there are 3 responses available for the recipient to receive the call by pressing 1
32. n will not trigger alarm when its tamper is violated lt NOTE gt f disabled the siren tamper will be automatically enabled after one hour 19 Confirmation Setting The siren can be enabled or disabled for arming and disarming confirmation When set to Enabled the Siren will beep when the system is armed or disarmed to confirm the mode change When set to Disabled the Siren will not activate when system mode is changed Entry Exit Setting The Outdoor Siren and Indoor Siren can be enabled or disabled from sounding warning beeps during Entry Time and Exit Time When set to Enabled the Siren will beep during Entry and Exit Time When set to Disabled the Siren will not beep during Entry and Exit Time Learn Repeater Optional Repeater required Use this function to send add the Repeater device into your alarm system Put your repeater into learning mode the send the SMS command to the Control Panel The panel will transmit signal to Repeater upon receiving the SMS command Please refer to Repeater manual for further detail 20 PSS Control Optional Power Switch required The Power Switches can be controlled manually or through Home Automation settings to turn on off you home appliance remotely to monitor your home environments Back PSS Control Save PSS channel On Action Attribute PSS Learning 1 Put the Power Switch into Learning mode Please refer to Power Switc
33. ng process the control panel will start counting down see below while emitting small beeps periodically Upon finishing the countdown the control panel will emit small beeps depending on your arm mode 3 quick beeps for home arming 1 long beep for away arming Exit Delay Timer After initiating the arming process the users are given time to exit the premises before the system is armed The exit delay timer is configurable with the Connect2Home application or through the SMS command Stopping the Exit Timer You can stop the exit timer before it finishes counting down To do that you can either 1 Press the disarm key on the remote controller or 2 Select disarm on the Connect2Home application or Extending the Exit Tlmer You can reset the exit timer to its initial duration before it finishes counting down 1 Press and hold the Away Arm or Home Arm key on the Remote Controller Fault Events The Control Panel keeps track of the system condition and will alert the user when a fault is detected For example when the door contact is not aligned with the magnet or when its tamper switch is activated When faults exist in system the Fault LED will light up to indicate If the fault exists in the panel the Fault LED will stay lit If the fault exists in a device the Fault LED will start flashing If you have set a mobile number to SMS report for All Event or Status Events the Control Panel will also send a SMS mes
34. not support Capture Image function please skip this option 18 Edit Device Siren Control Optional Siren required The Edit Device option allows you to edit a The Siren Control option allows you to device name and attribute for Door Contact change Siren settings PIR and EIR Sensor Back Edit Device Zone Name Attribute Delete This Device Select the Zone number of the device you want to edit and enter a new name For Door Contact and PIR Sensor please select an attribute For other devices without attribute you can select any attribute as it will not affect the device setting Press Save A SMS message edit screen will appear for you to confirm Press Send to send the SMS command to panel You can also remove the device specified by oressing Delete This Device Back Siren Control Attribute Tamper Enable Attribute Tamper Confirm Select the function you want to edit and choose to enable or disable the function Press Save A SMS message edit screen will appear for you to confirm Press Send to send the SMS command to panel Tamper setting The siren has built in tamper protection function to raise alarm when they are being removed from the mounted location or have their covers opened The tamper protection can be temporarily disabled When set to Enabled the tamper protection is activated When set to Disabled the Sire
35. or Alarm Event condition set the events for the Power Switch to be activated deactivated you can set more than one events Press Save The phone will send a SMS command to panel to program the Home Automation setting Home Automation Settings SAVE If panel is set to Arm Enable Rule PSS Channel Switch Duration For system mode change Arm Home Disarm the Power Switch channel selection is limited to 1 only For High Low Temperature and Time setting You can select any Power Switch channel from 1 4 Higher Lower temperature setting in Home Automation Rules does not affect High Low temperature report setting Time condition is disabled for SA2500 Please ignore this function 31 6 System Information and Operation This chapter covers system general characteristic under normal operation IMPORTANT NOTE lf you operate your alarm system via Connect2Home application please be reminded that the SMS command messages sent with Connect2Home application will incur extra cost Arming Disarming the System To change the modes you can use the Connect2Home Application or the remote controller Away Arm 1 Press the Arm button on the Connect2Home application or 2 Press the Arm button on the remote controller Home Arm 1 Press the Home Arm button on the Connect2Home application or 2 Press the Home Arm button on the remote controller After initiating the armi
36. pplied to power the Control Panel Please wait until a SIM card is inserted before connecting the adaptor In addition to the adaptor there is a rechargeable battery inside the Control Panel that serves as back up power in case of power failure Once you have connected the AC power supply please turn on the battery switch to charge the battery It takes about 72 hours to fully charge the battery When fully charged the battery can serve as a back up power source for about 18 hours IMPORTANT NOTE The Battery Switch is set to OFF by factory default Please make sure the switch is turned ON after connecting the AC power to the Control Panel otherwise the battery will not be charged and the Control Panel will be without back up power when power fails The Control Panel requires a SIM card to send reports and receive commands Before you insert the SIM card into GSM module please note the following 1 The SIM card must be able to make and receive both telephone calls and SMS messages normally Data only SIM cards are NOT compatible with the Control Panel 2 Please make sure SIM card PIN code is disabled To check whether SIM Card PIN code is disabled insert the SIM card into a working mobile phone go to SIM card PIN code setting in mobile phone setting functions to disable the SIM card PIN code 3 If a prepaid SIM card is used please check the SIM card information carefully as each SIM card provider has their own policy Some S
37. r it is triggered Please wait for at least 1 minute before testing PIR again PIR battery is exhausted please change a battery PIR is responding slowly This is normal PIR has sophisticated false arm filter setting to prevent accidental trigger It is also less sensitive when walking directly toward it 36 PIR giving false alarm Make sure pets have no access to protected area Make sure the PIR is not pointed at source of heat or moving objects Door Contact Door Contact LED flashing when activated Door Contact is on low battery or tamper switch triggered Door Contact is not responding to door window opening Door Contact battery is exhausted please change battery The magnet is too far away from the Door Contact please check the gap between the magnet and the Door Contact Reduce the gap and test the Door Contact again Remote Controller Remote Controller LED glows dimply when any key is pressed Remote Controller on low battery Connect2Home Application The system is not responding to SMS command Make sure the Control Panel GSM signal is normal Make sure the SMS Keyword and PIN Code in the application is identical to Control Panel setting Avoid sending multiple command s in a short time Wait until receiving confirmation message from the Control Panel before sending the next command Factory Reset The Factory Reset function will delete all learned in devices and return
38. s all system setting to default value After the setting you will need to setup the system again from the beginning via First Time Setup 1 Power down Control Panel and turn off the battery switch 2 Apply power while holding down the Function key 3 All LEDs will flash for 5 times 4 All programmed parameters are reset to factory default setting NOTE Once the Factory Reset is executed all the programmed data are returned to its default value and all the devices having been learnt in are removed You have to do the programming and learn in the device one by one again 37 8 Specifications All Devices Environmental Condition 10 C to 40 C relative humidity 85 non condensing for Control Panel and all devices Radio Operation Range About 30m in typical domestic installation range can vary depending on building construction device location and environment Control Panel Siren Output 96 dBA sound pressure 1m minimum Zones 30 radio devices Plus 4 optional Power Switches Power Supply 9VDC 1A Power Adaptor Battery 4 8V 600MAH Ni MH Rechargeable Battery charge time 72 hours Battery Backup Time 18 hours PIR Sensor Radio Frequency 868MHz Battery 1 x 3V lithium battery Door Contact Radio Frequency 868MHz Battery 1 x 3V 1 2 AA lithium battery Remote Controller Radio Frequency 868MHz Battery 1 x CR2032 3V lithium coin cell 38 Compliance Statement Declaration of Conformit
39. sage to notify you when fault is detected 32 Force Arm If you try to arm the system when fault exists the Control Panel will emit a beep to indicate failure You can choose to arm the system anyway and ignore the faults by force arming the system For the remote controller press and hold the away arm home arm key again and the Control Panel will initiate the arming process and begin counting down the Exit Timer NOTE Force Arm is not required for Connect2Home Application The Control Panel will enter selected arm mode upon directly and report back a SMS message to remind you of the existing faults Up to 3 faults can be included in the SMS message Disarm When the system is under Away arm or Home Arm mode to disarm the system 1 For Remote Controller press Disarm key 2 For Connect2Home application simply press the Disarm button Entry Delay Timer When a Door Contact or PIR sensor set to Entry attribute is triggered the system will begin an Entry Delay countdown timer according to Entry Time setting The reason for this is to give the users some time to disarm the system when you enter your home You need to disarm the system before the timer expires or a burglar alarm will be activated Alarm Activation 1 When a device previously set to Burglar is triggered the alarm will be activated immediately 2 When a device previously set to Entry is triggered the Entry countdown timer will be activated
40. ting are separated into three types Alarm Status All Alarm if there is an alarm event the control panel will send the alarm information to the programmed phone number Status If there is a status change from Arm to Home Arm etc the control panel will send the status change information to the programmed phone number All lf there is a status change or alarm event the control panel will send the aforesaid information to the programmed phone number lt My Panel Reporting Settings Reporting 1 Reporting 2 Reporting 3 Reporting 4 Reporting 5 Reporting 6 Select the reporting priority you wish to edit Enter the telephone number for reporting and select report type and events Press Save A SMS message edit screen will appear for you to confirm Press Send to send the SMS command to panel There are no event options for voice reporting the option to choose Events will be dimmed Device Setting Back R ing 1 ae eporting The Device Setting Menu allows you to edit device control Siren Optional Siren Device SIM required and learn in or control Power Switch Optional Power Switch required Type SMS Events sell Al lt My Panel Device Settings Edit Device Siren Control PSS Control Capture Image lt NOTE gt You can delete the telephone number by keeping the telephone number field blank and save the setting SA2500 Control Panel does
41. wing steps 1 Under Disarm mode press and hold the Function Button for 8 seconds and release when the Control Panel emits 1 beep 2 The Control Panel will emit another long beep after 3 seconds to indicate recording is started 3 Speak clearly and slowly for the Control Panel to record your address message When you have finished recording press the Function Button once to stop recording or the recording will stop automatically when it reaches 10 seconds 4 Recording is now complete the Control Panel will return to the Disarm mode Device Learning The process of adding devices into the control panel is called Learning The control panel needs to learn in the accessory devices setup a complete alarm system Please see below for learning instruction NOTE The devices included in the SA 2500 Kit are already learned into the system For these devices please proceed directly to Mounting section below 1 Under Disarm mode press the Function Button once the Control Panel will emit 1 beep and the Mode LED will begin to flash to indicate the Control Panel is now under Learning Mode 2 Under Learning mode press the learn test button on your accessory device to transmit a learn code Please refer to the device manual for detail 3 The Control Panel will emit 1 beep upon receiving the learn code to indicate the device is successfully learnt in 4 After learning all devices press the Function button again The Control
42. y This device complies with the requirements of the R amp TTE Directive 1999 5 EC and the following harmonized standards have been applied Health EN50385 2002 Safety EN60950 1 2006 A11 2009 A1 2010 A12 2011 EMC EN 301 489 1 V1 9 2 2011 09 EN 301 489 3 V1 4 1 2002 08 EN 301 489 7 V1 3 1 2005 1 1 Radio 3GPP TS 51 010 1 V9 8 0 EN 301 511 V9 0 2 GSM 13 11 3GPP TS 51 010 1 V9 8 0 3GPP TS 51 010 2 V9 0 1 3SGPP TS 51 010 4 V4 14 1 3GPP TS 51 010 5 V9 0 1 EN 300 220 2 V2 4 1 2012 05 FCC FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FCC Caution To assure continued compliance any changes or modifications not expressly approved by the party responsible for compliance may void the user s authority to operate this equipment Example use only shielded interface cables when connecting to computer or peripheral devices Blaupunkt Competence Center Security amp Care www blaupunkt com Sissoo Technologies Prins Bernhardstraat 70 5721GD Asten The Netherlands FE CE QE amp BLAUPUNKT
43. ync Device Zone 1 5 Sync Device Zone 6 10 D Sync Device Zone 11 15 Sync Device Zone 16 20 Sync Device Zone 21 25 Sync Device Zone 26 30 Device Type information will only be updated after you successfully synced with the Control Panel Device Settings Edit Device Zone Attribute Burglar device A Name Door Contact Device Type Delete This Device Siren Control Optional Siren required The Siren Control option allows you to change Siren settings Device Settings Siren Control Attribute Tamper Enable Kemps Confirm Entry Exit Learn RP Select the attribute and choose to enable or disable the function Press Save The phone will send a SMS command to panel Tamper setting The siren has tamper protection function to raise alarm when it is removed from the mounted location or its covers opened The tamper function can be temporarily disabled When set to Enabled the tamper protection is activated When set to Disabled the Siren will not trigger alarm when its tamper is violated Confirmation Setting The Outdoor Siren and can be enabled or disabled for arming and disarming confirmation When set to Enabled the Siren will beep when the system is armed or disarmed to confirm the mode change When set to Disabled the Siren will not beep when system mode is changed 29 Entry Exit Setting The Outdoor Siren and
Download Pdf Manuals
Related Search