Safety and Reference
Contents
1. When cleaning the product and its components unplug the power first and wipe it with a soft cloth Applying excessive force may cause scratches or discolouration Do not spray with water or wipe with a wet cloth Never use glass cleaner car or industrial shiner abrasives or wax benzene alcohol etc which can damage the product and its panel Otherwise this may result in fire electric shock or product damage deformation corrosion or breakage As long as this unit is connected to the AC wall outlet it is not disconnected from the AC power source even if you turn off this unit by SWITCH When unplugging the cable grab the plug and unplug it by pulling at the plug Don t pull at the cord to unplug the power cord from the power board as this could be hazardous When moving the product make sure you turn the power off first Then unplug the power cables antenna cables and all connecting cables The TV set or power cord may be damaged which may create a fire hazard or cause electric shock e vj a amp o gt When moving or unpacking the product work in pairs because the product is heavy Otherwise this may result in injury Contact the service centre once a year to clean the internal parts of the product Accumulated dust can cause mechanical failure Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in2. e not connect a modular phone cable to the LAN port e Since there are various connection methods please follow the specifications of your telecommunication carrier or internet service provider Other connections Connect your TV to external devices For the best picture and audio quality connect the external device and the TV with the HDMI cable Some separate cable is not provided Remote control Depending on model The descriptions in this manual are based on the buttons on the remote control Please read this manual carefully and use the TV correctly To replace batteries open the battery cover replace batteries 1 5 V AAA matching the ends to the label inside the compartment and close the battery cover To remove the batteries perform the installation actions in reverse CAUTION Do not mix old and new batteries as this may damage the remote control e The remote control will not be included for all sales market Make sure to point the remote control toward the remote control sensor on the TV RATIO INPUT 8e B SUBTITLE i A 1 POWER Turns the TV on or off TV RAD IBii C Selects Radio TV and DTV programme SUBTITLE Recalls your preferred subtitle in digital mode AV MODE Selects an AV mode CJ RATIO Resizes an image EJINPUT Changes the input source Number buttons Enters numbers LIST Accesses the saved programme list Q VIEW Returns to
3. LG Life s Good OWNER S MANUAL Safety and Reference LED TV LG LED TV applies LCD screen with LED backlights Please read this manual carefully before operating your set and retain it for future reference www lg com Z C Safety instructions Please read these safety precautions carefully before using the product A WARNING Do not place the TV and or remote control in the following environments A location exposed to direct sunlight An area with high humidity such as a bathroom e Near any heat source such as stoves and other devices that produce heat Near kitchen counters or humidifiers where they can easily be exposed to steam or oil Anarea exposed to rain or wind Near containers of water such as vases Otherwise this may result in fire electric shock malfunction or product deformation Do not place the product where it might be exposed to dust This may cause a fire hazard Mains Plug is the TV connecting disconnecting device to AC mains electric supply This plug must remain readily attached and operable when TV is in use Do not touch the power plug with wet hands Additionally if the cord pin is wet or covered with dust dry the power plug completely or wipe dust off You may be electrocuted due to excess moisture Make sure to connect Mains cable to compliant AC mains socket with Grounded earth pin Except for devices which are not grou
4. Free Format Sample freq 48 kHz Support OGG Vorvis Supported photo formats Category 2D jpeg jpg jpe Available file type SOFO Baseline SOF1 Extend Sequential SOF2 Progressive Photo size Minimum 64 x 64 Maximum Normal Type 15360 W x 8640 H Progressive Type 1920 W x 1440 Category BMP Photo size Minimum 64 x 64 Maximum 9600 x 6400 Category PNG Available file type Interlace Non Interlace Photo size Minimum 64 x 64 Maximum Interlace 1200 x 800 Non Interlace 9600 x 6400 BMP and PNG format files may be slower to display than JPEG m m U u 21 LG Life s Good Record the model number and serial number of the TV Only DTV Refer to the label on the back cover and quote this information to your dealer when requiring any service MODEL 2 2 J Digital Video SERIAL Broadcasting
5. the floor When you attach theTV to other building materials please contact qualified personnel LG recommends that wall mounting be performed by a qualified professional installer We recommend the use of LGs wall mount bracket When you do not use 165 wall mount bracket please use a wall mount bracket where the device is adequately secured to the wall with enough space to allow connectivity to external devices Make sure to use screws and wall mount bracket that meet the VESA standard Standard dimensions for the wall mount kits are described in the following table Separate purchase Wall Mounting Bracket 221922 2019228 220066 28L33 ZS 28LX53 VESA A x B 75x75 100 x 100 M4 x L10 M4 x L10 4 per mount LSW140 LSW140 bracket 49 551 34 Me 49LX31 32 40 43LX54 491X32 VESA A x B 200 x 200 300 x 300 4 LSW350B MSW240 42LX32 42LX33 42LX53 Wall mount LSW240B bracket MSW240 60LX34 60LX54 VESA A x B 300 x 300 400 x 400 Wall mount LSW440B 11 U 12 N CAUTION e Disconnect the power first and then move or install the TV Otherwise electric shock may occur e Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse e Ifyou install the TV on a ceiling or slanted wall it may fall and result in severe injury Use an authorised LG wall mount and c
6. 4 Part2 DivX3 11 DivX4 DivX5 DivX6 XVID H 264 AVC Audio AAC MPEG 1 Layer III DTS e mkv Video MPEG 2 MPEG 4 Part2 DivX3 11 DivX4 DivX5 DivX6 XVID H 264 AVC Audio HE AAC Dolby Digital MPEG 1 Layer III MP3 DTS LPCM e motion JPEG Video MJPEG Audio LPCM ADPCM mpg mpeg mpe Video MPEG 1 MPEG 2 Audio MPEG 1 Layer MPEG 1 Layer Il Dolby Digital LPCM e dat Video MPEG 1 MPEG 2 Audio MP2 gt flv Video Sorenson H 263 H 264 AVC Audio MP3 AAC HE AAC rm rmvb Video RV30 RV40 Audio Dolby Digital AAC HE AAC RA6 Cook 39 39 2 Video H 264 AVC MPEG 4 Part2 Audio AAC AMR NB WB DTS rm rmvb Depending on model Supported audio formats File type mp3 Bit rate 32 Kbps 320 Kbps Sample freq 16 kHz 48 kHz Support MPEG1 MPEG2 Layer2 Layer3 File Type Bit rate Free Format Sample freq 8 kHz 48 kHz Support ADIF ADTS File Type Bit rate Free Format Sample freq 8 kHz 48 kHz Support MPEG 4 File Type WMA Bit rate 128 Kbps 320 Kbps Sample freq 8 kHz 48 kHz Support WMA7 WMA8 WMA Standard File Type WMA 10 Pro Bit rate 768 Kbps Channel Sample freq MO up to 2 Channel 48 kHz Except LBR mode M1 up to 5 1 Channel 48 kHz M2 up to 5 1 Channel 96 kHz Support WMA 10 Pro File Type OGG Bit rate
7. Sets the alarm function depending on model Licenses Supported licenses may differ by model For more information about licenses visit www lg com I DOLBY DIGITAL PLUS Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories HIGH DEFINITION MULTIMEDIA INTERFACE The terms HDMI and HDMI High Definition Multimedia interface and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries HD This DivX Certified device has passed rigorous testing to ensure it plays DivX video To play purchased DivX movies first register your device at vod divx com Find your registration code in the DivX VOD section of your device setup menu DivX Certified to play DivX video up to HD 1080p including premium content DivX DivX Certified and associated logos are trademarks of DivX LLC and are used under license Covered by one or more of the following U S patents 7 295 673 7 460 668 7 515 710 7 519 274 Open source software notice information To obtain the source code under GPL LGPL MPL and other open source licenses that is contained in this product please visit http opensource Ige com C U I In addition to the source code all referred license terms warranty disclaimers and copyright notices are available for download LG Electronics will also provide open so
8. product Do not spray liquid onto the surface If water enters the TV it may result in fire electric shock or malfunction Power cord Remove the accumulated dust or dirt on the power cord regularly Lifting and moving the TV Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size tis recommended to move the TV in the box or packing material that the TV originally came in Before moving or lifting the TV disconnect the power cord and all cables When holding the TV the screen should face away from you to avoid damage Hold the top and bottom of the TV frame firmly Make sure not to hold the transparent part speaker or speaker grill area inl LL When transporting a large TV there should be at least 2 people When transporting the TV by hand hold the TV as shown the following illustration e When transporting the TV do not expose the TV to jolts or excessive vibration When transporting the TV keep the TV upright never turn the TV on its side or tilt towards the left or right e Do not apply excessive pressure to cause flexing bending of frame chassis as it may damage screen When handling the TV be careful not to damage the protruding joystick button Depending on model CAUTION Avoid touching the screen at all times as this may result in damage to the scre
9. screen for a prolonged period Also if you watch the TV at a ratio of 4 3 for along time image sticking may occur on the borders of the panel This phenomenon also occurs in third party products and is not subject to exchange or refund Generated Sound Cracking noise A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to tempera ture and humidity This noise is common for products where thermal deformation is required Electrical circuit humming panel buzzing A low level noise is generated from a high speed switching circuit which supplies a large amount of current to operate a product It varies depending on the product This generated sound does not affect the performance and reliability of the product Do not use high voltage electrical goods near the TV e g electric mosquito swatter This may result in product malfunction Preparing NOTE Image shown may differ from your TV YourTV s OSD On Screen Display may differ slightly from that shown in this manual e The available menus and options may differ from the input source or product model that you are using New features may be added to this TV in the future TheTV can be placed in standby mode in order to reduce the power consumption And the TV should be turned off if it will not be watched for some time as this will reduce energy consumption The energy consumed during use can
10. 5305 information RGB PC supported mode ComponentportsontheTV Y Py Py Only LX32 LX33 LX34 LX31 LX5405 1 5305 Horizontal Vertical Frequency kHz Frequency Hz 640 x 350 31 468 70 09 Resolution Video output ports on DVD player AOI o 1152 x 864 54 348 60 053 Dit 0 0 0 am 0 Only 50 Hz 60 Hz 63 981 60 020 1920 x 1080 FHD only eee 59 934 1920x 1080 FHD only Dus 60 00 480i 576i 1280 x 1024 FHD only E Only LX341 42LX330 42LX320 LX310 LX540S 1 5305 19 m C U 20 Supported video formats Maximum 1920 x 1080 30p only Motion JPEG 640 x 480 30 e sf wmv Video MPEG 2 MPEG 4 Part2 DivX3 11 DivX4 DivX5 DivX6 XViD H 264 AVC VC1 WMV3 WVC1 Audio WMA Standard WMA9 Pro MP3 AAC AC3 MP3 3D WMV Single Stream e divx avi Video MPEG 2 MPEG 4 Part2 DivX3 11 DivX4 DivX5 DivX6 XViD H 264 AVC Audio HE AAC LPCM ADPCM MPEG 1 Layer MPEG 1 Layer Il Dolby Digital 1 Layer III DTS ts trp tp mts m2ts Video H 264 AVC MPEG 2 AVS VC1 Audio MPEG 1 Layer MPEG 1 Layer Il MPEG 1 Layer III Dolby Digital Dolby Digital Plus AAC HE AAC DTS vob Video MPEG 1 MPEG 2 Audio Dolby Digital MPEG 1 Layer MPEG 1 Layer Il DVD LPCM mp4 m4v mov Video MPEG 2 MPEG
11. T Changes the input source TV RAD 88 0 Selects Radio TV and DTV programme Number buttons Enters numbers LIST Accesses the saved programme list Q VIEW Returns to the previously viewed programme 1 Adjusts the volume level FAV Accesses your favourite programme list RATIO Resizes an image MUTE Sf Mutes all sounds P v Scrolls through the saved programmes PAGE Moves to the previous or next screen S Gm Mme GOGOC GUIDE Shows programme guide PORTAL Displays and removes hotel interactive menu INFO 1 Views the information of the current programme and screen Navigation buttons up down left right Scrolls through menus or options OK Selects menus or options and confirms your input SETTINGS Accesses the main menus D BACK Returns to the previous level EXIT Clears on screen displays and return to TV viewing Coloured buttons These access special functions i in some menus GD Red Ge Green Yellow D Teletext buttons TEXT T OPT These buttons are used for teletext SUBTITLE Recalls your preferred subtitle in digital mode Control buttons Bl gt 11 44 Controls the MY MEDIA menus or the SIMPLINK compatible devices USB SIMPLINK SJmMPuink Accesses the AV devices connected with the HDMI cable through HDMI CEC Opens the SIMPLINK menu Q MENU Accesses the Quick menus AD By pressing the AD button audio descriptions function will be enabled ALARM
12. any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Ap vit eem 0 If the product feels cold to the touch there may be a small flicker when it is turned on This is normal there is nothing wrong with product The panel is a high technology display product with resolution of two million to six million pixels You may see tiny black dots and or brightly coloured dots red blue or green at a size of 1 ppm on the panel This does not indicate a malfunction and does not affect the performance and reliability of the product This phenomenon also occurs in third party products and is not subject to exchange or refund You may find different brightness and color of the panel depending on your viewing position left right top down This phenomenon occurs due to the characteristic of the panel It is not related with the product performance and it is not malfunction Displaying a still image e g broadcasting channel logo on screen menu scene from a video game for a prolonged time may cause damage to the screen resulting in retention of the image which is known as image sticking The warranty does not cover the product for image sticking Avoid displaying a fixed image on your television s
13. be significantly reduced if the level of brightness of the picture is reduced and this will reduce the overall running cost The items supplied with your product may vary depending on the model Product specifications or contents of this manual may be changed without prior notice due to upgrade of product functions e For an optimal connection HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width Use an extension cable that supports USB 2 0 if the USB cable or USB memory stick does not fit into your TV s USB port Use a certified cable with the HDMI logo attached f you do not use a certified HDMI cable the screen may not display or a connection error may occur Recommended HDMI Cable Types High Speed HDMI cable 3 m or less High Speed cable with Ethernet 3 m or less CAUTION Do not use any unapproved items to ensure the safety and product life span Any damage or injuries caused by using unapproved items are not covered by the warranty Some models have a thin film attached on to the screen and this must not be removed e When attaching the stand to the TV set place the screen facing down on a cushioned table or flat surface to protect the screen from scratches Make sure that the screws are fastened completely If they are not fastened securely enough the TV may tilt forward after being installed Do not use too much force and over tight
14. en Do not move the TV by holding the cable holders as the cable holders may break and injuries and damage to the TV may occur Using the joystick button Image shown may differ from your TV You can simply operate the TV functions pressing or moving the joystick button up down left or right Joystick Button When the TV is turned off place Power On your finger on the joystick button and press it once and release it When the TV is turned on place your finger on the joystick button and press it once for a few seconds Power Off and release it However if the Menu button is on the screen pressing and holding the joystick button will let you exit the Menu If you place your finger over the joystick button and move it left or right you can adjust the volume level you want If you place your finger over the Programmes joystick button and move it up or Control down you can scrolls through the saved programmes you want Adjusting the Menu When the TV is turned on press the joystick button one time You can adjust the Menu items moving the joystick button up down left or right Turns the power off Clears on screen displays and returns to TV viewing U u Changes the input source Accesses the main menu Q NOTE When your finger over the joystick button and push it to the up down left or right be careful not to p
15. en the screws otherwise screw may be damaged and not tighten correctly m 2 U T Z C U Separate purchase Separate purchase items can be changed or modified for quality improvement without any notification Contact your dealer to buy these items These devices only work with certain models The model name or design may be changed depending on the upgrade of product functions manufacturer s circumstances or policies Depending on model LED Clock LEC 003 LG Audio Device Maintenance Cleaning your TV Clean your TV regularly to keep the best performance and to extend the product lifespan Make sure to turn the power off and disconnect the power cord and all other cables first e When the TV is left unattended and unused for a long time disconnect the power cord from the wall outlet to prevent possible damage from lightning or power surges Screen frame cabinet and stand To remove dust or light dirt wipe the surface with a dry clean and soft cloth To remove major dirt wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent Then wipe immediately with a dry cloth Avoid touching the screen at all times as this may result in damage to the screen e Do not push rub or hit the screen surface with your fingernail or a sharp object as this may result in scratches and image distortions e Do not use any chemicals as this may damage the
16. he product in a place with no ventilation e g on a bookshelf or in a cupboard Do not install the product on a carpet or cushion Make sure the air vent is not blocked by a tablecloth or curtain Otherwise this may result in fire ye SS Take care not to touch the ventilation openings when watching the TV for long periods as the ventilation openings may become hot This does not affect the operation or performance of the product Periodically examine the cord of your appliance and if its appearance indicates damage or deterioration unplug it discontinue use of the appliance and have the cord replaced with an exact replacement part by an authorized servicer fij t s AND OA Prevent dust collecting on the power plug pins or outlet This may cause a fire hazard C Protect the power cord from physical or mechanical abuse such as being twisted kinked pinched closed in a door or walked upon Pay particular attention to plugs wall outlets and the point where the cord exits the appliance Do not press strongly upon the panel with a hand or sharp object such as nail pencil or pen or make a scratch on it as it may cause damage to screen Avoid touching the screen or holding your finger s against it for long periods of time Doing so may produce some temporary or permanent distortion damage to screen
17. information of recording refer to the manual provided with the connected device Refer to the external equipment s manual for operating instructions e Ifyou connect a gaming device to the TV use the cable supplied with the gaming device In PC mode there may be noise associated with the resolution vertical pattern contrast or brightness If noise is present change the PC output to another resolution change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear In PC mode some resolution settings may not work properly depending on the graphics card Antenna connection Connect the TV to a wall antenna socket with an RF cable 75 0 e Use a signal splitter to use more than 2 TVs e Ifthe image quality is poor install a signal amplifier properly to improve the image quality Ifthe image quality is poor with an antenna connected try to realign the antenna in the correct direction Anantenna cable and converter are not supplied Supported DTV Audio MPEG Dolby Digital Dolby Digital Plus HE AAC Satellite dish connection Only satellite models Connect the TV to a satellite dish to a satellite socket with a satellite RF cable 75 0 U 13 14 Adapter connection Depending on model CAUTION Please be sure to connect the TV to the AC DC power adapter before connecting the TV s power
18. ldren Do not let your children climb or cling onto the TV Otherwise the TV may fall over which may cause serious injury me 4 Dispose of used batteries carefully to ensure that a small child does not consume them Please seek Doctor Medical Attention immediately if child consumes batteries Do not insert any metal objects conductors like a metal chopstick cutlery screwdriver between power cable plug and input Wall Socket while it is connected to the input terminal on the wall Additionally do not touch the power cable right after plugging into the wall input terminal You may be electrocuted Depending on model Do not put or store inflammable substances near the product There is a danger of combustion explosion or fire due to careless handling of the inflammable substances Do not drop metallic objects such as coins hair pins chopsticks or wire into the product or inflammable objects such as paper and matches Children must pay particular attention Electrical shock fire or injury can occur If a foreign object is dropped into the product unplug the power cord and contact the service centre C m U u Do not spray water on the product or scrub with an inflammable substance thinner or benzene Fire or electric shock accident can occur Do not allow any impact shock or any objects to fall into the unit and do not drop anything onto the screen You may be injured o
19. nded on earth Otherwise possibility you may be electrocuted or injured Insert power cable plug completely into wall socket otherwise if not secured completely into socket fire ignition may break out E 2s S een AA Ensure the power cord does not come into contact with hot objects such as a heater This may cause a fire or an electric shock hazard Do not place a heavy object or the product itself on power cables Otherwise this may result in fire or electric shock Bend antenna cable between inside and outside building to prevent rain from flowing in This may cause water damaged inside the Product and could give an electric shock When mounting TV onto wall make sure to neatly install and isolate cabling from rear of TV as to not create possibility of electric shock fire hazard x gt Qm 02 EP VIS Do not plug too many electrical devices into a single multiple electrical outlet Otherwise this may result in fire due to over heating Do not drop the product or let it fall over when connecting external devices Otherwise this may result in injury or damage to the product Te e Keep the anti moisture packing material or vinyl packing out of the reach of children Anti moisture material is harmful if swallowed If swallowed by mistake force the patient to vomit and visit the nearest hospital Additionally vinyl packing can cause suffocation Keep it out of the reach of chi
20. onment Operating Humidity Less than 80 condition Storage Temperature 20 C to 60 C Storage Humidity Less than 85 Manufacturer APD Model DA 48F19 AC DC Adapter Manufacturer Lien chang Only 22 28LX32 22 28LX33 22 28LX53 Model LCAP35 In AC 100 240 V 50 60 Hz Out DC 19V 2 53 A DD Satellite Digital TV Digital TV Analogue TV DVB T T2 PAL SECAM B G D K Television system DVB C PAL I I DVB S S2 SECAM L L VHF E2 to E12 VHF UHF UHF E21 to E69 C Band Ku Band CATV 51 to 520 HYPER 21 to S47 Maximum number of 6 000 1 500 storable programmes External antenna impedance 750 HSITDN4 Programme coverage 1 Satellite and DVB T2 support models 18 HDMI DVI DTV supported mode HDMI DVI PC supported mode Use HDMI IN 1 for PC mode Resoluti Horizontal Vertical Frequency kHz Frequency Hz Only LX31 LX32 LX33 DG4 LX53 DX54 Horizontal Vertical 720x480 59 94 0 Frequency kHz Frequency Hz 720x576 3125 0 640 x 350 31 468 70 09 37 5 5 1280 x 720 44 96 59 94 j 45 60 720 x 400 31 469 70 08 1920 x 1080 640 x 480 31 469 59 94 Resolution 1024 x 768 60 00 1152 x 864 60 053 1360 x 768 60 015 1280 x 1024 60 020 1920 x 1080 woo 000000 0 800 600 37 879 60 31 E Only LX341 42LX330 42LX320 LX310 LX54 1530 Component port connecting E Only LX341 42LX330 42LX320 LX310 LX54 15
21. ontact the local dealer or qualified personnel Do not over tighten the screws as this may cause damage to the TV and void your warranty Use the screws and wall mounts that meet the VESA standard Any damages or injuries by misuse or using an improper accessory are not covered by the warranty Screw length from outer surface of back cover should be under 8 mm Only 22 28LX32 22 28LX33 22 28LX53 Wall mount Pad A Back Cover Wall mount Pad Back Cover Standard screw e M4x L10 Max 8 mm Q NOTE e Use the screws that are listed on the VESA standard screw specifications The wall mount kit includes an installation manual and necessary parts The wall mount bracket is not provided You can obtain additional accessories from your local dealer The length of screws may differ depending on the wall mount Make sure to use the proper length For more information refer to the manual supplied with the wall mount When installing the wall mounting bracket use the adhesive label provided The adhesive label will protect the opening from accumulating dust and dirt Only when the label is provided Provided Item 3 E Adhesive label e When attaching a wall mounting bracket to the TV insert the wall mount spacers into the TV wall mount holes to adjust the vertical angle of the TV Only when the i
22. plug to a wall power outlet CI module connection Depending on model View the encrypted pay services in digital TV mode e Check if the Cl module is inserted into the PCMCIA card slot in the right direction If the module is not inserted properly this can cause damage to the TV and the PCMCIA card slot Ifthe TV does not display any video and audio when CI CAM is connected please contact to the Terrestrial Cable Satellite Service Operator Euro scart connection Depending on model Transmits the video and audio signals from an external device to the TV set Connect the external device and the TV set with the euro scart cable AVI TV Out Digital TV Analogue TV Current input mode Digital TV Analogue TV AV Component HDMI 1 TV Out Outputs Analogue TV or Digital TV signals Any Euro scart cable used must be signal shielded Network setup Wired network connection Depending on model This TV can be connected to a Pro Centric server via the LAN port After making the physical connection the TV needs to be set up for network communication Connect the LAN port of the Modem or Router from Pro Centric server to the LAN port on the TV m Pro CentricServer ge M Broadband Modem RA Pro CentricServer L N CAUTION
23. r of the TV For more information of installation and using refer to the manual provided with the Kensington security system or visit http www kensington com Connect the Kensington security system cable between f theTV and a table 4 Screws Not supplied with TV TEUER ey SS Se ee Desk ap NOTE e Screw M5 x L L Table depth 8 10 mm ex Table depth 15 mm Screw M5 x 25 10 Securing the TV to a wall This feature is not available for all models 1 Insert and tighten the eye bolts or TV brackets and bolts on the back of the TV If there are bolts inserted at the eye bolts position remove the bolts first 2 Mount the wall brackets with the bolts to the wall Match the location of the wall bracket and the eye bolts on the rear of the TV 3 Connect the eye bolts and wall brackets tightly with a sturdy rope Make sure to keep the rope horizontal with the flat surface N CAUTION Make sure that children do not climb on or hang on the TV Q NOTE e Use a platform or cabinet that is strong and large enough to support the TV securely Brackets bolts and ropes are not provided You can obtain additional accessories from your local dealer Mounting on a wall Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to
24. r the product can be damaged Never touch this product or antenna during a thunder or lighting storm You may be electrocuted Never touch the wall outlet when there is leakage of gas open the windows and ventilate It may cause a fire or a burn by a spark Do not disassemble repair or modify the product at your own discretion Fire or electric shock accident can occur Contact the service centre for check calibration or repair C If any of the following occur unplug the product immediately and contact your local service centre The product has been impacted by shock The product has been damaged Foreign objects have entered the product The product produced smoke or a strange smell This may result in fire or electric shock Unplug the TV from AC mains wall socket if you do not intend to use the TV for a long period of time Accumulated dust can cause fire hazard and insulation deterioration can cause electric leakage shock fire Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus Do not install this product on a wall if it could be exposed to oil or oil mist This may damage the product and cause it to fall If water enters or comes into contact with TV AC adapter or power cord please disconnect the power cord and contact service cent
25. re immediately Otherwise this may result in electric shock or fire Only use an authorized AC adapter and power cord approved by LG Electronics Otherwise this may result in fire electric shock malfunction or product deformation Never Disassemble the AC adapter or power cord This may result in fire or electric shock N CAUTION There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls This may cause an electric shock Do not install the product on places such as unstable shelves or inclined surfaces Also avoid places where there is vibration or where the product cannot be fully supported Otherwise the product may fall or flip over which may cause injury or damage to the product If you install the TV on a stand you need to take actions to prevent the product from overturning Otherwise the product may fall over which may cause injury If you intend to mount the product to a wall attach VESA standard mounting interface optional parts to the back of the product When you install the set to use the wall mounting bracket optional parts fix it carefully so as not to drop Only use the attachments accessories specified by the manufacturer When installing the antenna consult with a qualified service technician If not installed by a qualified technician this may create a fire hazard or an elec
26. ress the joystick button If you press the joystick button first you may not be able to adjust the volume level and saved programmes Mounting on a table Depending on model 1 Lift and tilt the TV into its upright position on a table Leave a 10 cm minimum space from the wall for proper ventilation 2 Connect the power cord to a wall outlet N CAUTION Do not place the TV near or on sources of heat as this may result in fire or other damage Adjusting the angle of the TV to suit view Depending on model Swivel 20 degrees to the left or right and adjust the angle of the TV to suit your view 2 Screws for Stand Fixing CAUTION 2 Washers for Stand Fixing 2 Nuts for Stand Fixing Supplied with TV e When adjusting the angle of the product watch out for your fingers Personal injury may occur if hands or fingers are pinched If the product is tilted too much it may fall causing damage or injury Attaching the TV to a desk ay Depending on model The TV should be attached to a desk so it cannot be pulled in a forward Desk backward direction potentially causing injury or damaging the product A type Using the kensington security system This is not available for all models Image shown may differ from your TV The Kensington security system connector is located at the rea
27. tem of the following form is provided Provided Item Wall Mount Spacer How to use Dual Lock Only when the item of the following form is provided This feature is not available for all models Fix the set top box to the TV and use it when you want to 1 After removing the protection paper from the Dual Lock stick it to the TV and the set top box as shown Dual Lock 2 Attach the set top box to the TV by pressing the Velcro strips together aD NOTE e Please make sure no foreign substances exist on the surface of the product and then firmly attach the Dual Lock Before attaching the set top box to the TV set let the attached Dual Lock dry for at least three days Connections notifications Connect various external devices to the TV and switch input modes to select an external device For more information of external device s connection refer to the manual provided with each device Available external devices are HD receivers DVD players VCRs audio systems USB storage devices PC gaming devices and other external devices NOTE The external device connection may differ from the model e Connect external devices to the TV regardless of the order of the TV port Ifyou record a TV program on a DVD recorder or VCR make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR For more
28. the previously viewed programme 4 Adjusts the volume level FAV Accesses your favourite programme list GUIDE Shows programme guide MUTE Sf Mutes all sounds P v Scrolls through the saved programmes PAGE v Moves to the previous or next screen Ce JOD C Teletext buttons TEXT T OPT These buttons are used for teletext INFO 7 Views the information of the current programme and screen SETTINGS Accesses the main menus Q MENU Accesses the Quick menus OK Selects menus or options and confirms your input Navigation buttons up down left right Scrolls through menus or options C BACK Returns to the previous level EXIT Clears on screen displays and returns to TV viewing D S mr Link Accesses the AV devices connected with the HDMI cable through HDMI CEC Opens the SIMPLINK menu AD By pressing the AD button audio descriptions function will be enabled Control buttons Bl gt 11 gt Controls the MY MEDIA menus or the SIMPLINK compatible devices USB SIMPLINK Coloured buttons These access special functions in some menus C Red G2 Green Ge Yellow C889 Blue 15 m C m U u 16 ENERGY AVMODE INPUT 60606 SAVING DAR DAA 21153 p E vore a 1 POWER Turns the TV on or off ec ENERGY SAVING Adjusts the brightness of the screen to reduce energy consumption AV MODE Selects an AV mode INPU
29. tric shock hazard We recommend that you maintain a distance of at least 2 to 7 times the diagonal screen size when watching TV If you watch TV for a long period of time this may cause blurred vision Only use the specified type of battery This could cause damage to the remote control Do not mix new batteries with old batteries This may cause the batteries to overheat and leak Batteries should not be exposed to excessive heat For example keep away from direct Sunlight open fireplace and electric heaters Do not place non rechargeable batteries in charging device Make sure there are no objects between the remote control and its sensor Signal from Remote Control can be interrupted due to external internal lighting eg Sunlight fluorescent lighting If this occurs turn off lighting or darken viewing area When connecting external devices such as video game consoles make sure the connecting cables are long enough Otherwise the product may fall over which may cause injury or damage the product C m U u Do not turn the product On Off by plugging in or unplugging the power plug to the wall outlet Do not use the power plug for switch It may cause mechanical failure or could give an electric shock Please follow the installation instructions below to prevent the product from overheating The distance between the product and the wall should be more than 10 cm e Do not install t
30. urce code to you on CD ROM for a charge covering the cost of performing such distribution such as the cost of media shipping and handling upon email request to opensource lge com This offer is valid for three 3 years from the date on which you purchased the product Troubleshooting Cannot control the TV with the remote control Check the remote control sensor on the product and try again Check if there is any obstacle between the product and the remote control e Check if the batteries are still working and properly installed to Oto CQ No image display and no sound is produced Check if the product is turned on e Check if the power cord is connected to a wall outlet e Check if there is a problem in the wall outlet by connecting other products The TV turns off suddenly Check the power control settings The power supply may be interrupted Check ifthe Automatic Standby Depending on model Sleep Timer Off Time is activated in the TIME settings e Ifthere is no signal while the TV is on the TV will turn off automatically after 15 minutes of inactivity When connecting to the PC RGB HDMI DVI No signal or Invalid Format is displayed Turn the TV off on using the remote control e Reconnect the RGB HDMI cable Restart the PC with the TV on 17 Specifications Module Size W x H x D 100 0 mm x 55 0 mm x 5 0 mm Operating Temperature 0 C to 40 C Envir
Download Pdf Manuals
Related Search