45572D RF3341 User`s Guide.PMD
Contents
1. 4 0 Programmable ABC Keys The RF3341 Wireless Keypad has three keys which can be programmed by your installing company to perform functions including activating alarm responses and operating relays The programmable ABC keys are protected by a sliding cover so that they can t be pressed inadvertently The ABC keys must be pressed for two seconds to transmit a message At the end of two seconds the keypad will beep once and the LED will flash to indicate that a message has been sent aa ica LED 2 Entry a J Keys Option 8 Key 0 Programmable ale ABC Keys ae Here AOp E p E l ee Slide cover down to expose the ABC Keys 2004 Bosch Security Systems 130 Perinton Parkway Fairport New York USA 14450 9199 Customer Service 800 289 0096 Technical Support 888 886 6189 The ABC Key functions have been provided by your alarm company 5 0 Option Key y The Option Key may be programmed by your installing company to control other devices such as lights within the protected area 6 0 Battery Replacement The batteries will need to be replaced approximately every 3 years depending on usage If you notice the range of the Keypad is decreasing if the LED is not working or if the wired keypad LCD display indicates trouble for a low battery for this keypad it may be time to replace your battery Battery life will vary depending2. PIN code select the type of arming desired and then press the 9 key The following example is for full arming when the AC power has failed or if a zone is not ready Arming the System Full Arming Force Armed Enter your PIN code 1 2 3 4 Then enter 9 3 2 Disarming Your System Enter your PIN code 4 amp 4 Then enter The system will disarm 3 3 Partitioning You may have a Partitioned system In a partitioned system specific areas partitions may be armed while other areas remain disarmed RF3341 Wireless Keypads should be assigned to individual partitions or may be used to arm and disarm the entire system Only your installing company can change if a wireless keypad affects one partition or the entire system If the Wireless Keypad is set to arm and disarm the entire system you may assign User Codes PINs to arm and disarm individual partitions See Personal Identification Numbers in your system s User s Guide for additional information 3 4 Chime Mode When Chime Mode is turned On or Off the wired keypad s will briefly indicate its status When Chime Mode is turned On the wired keypads will chime whenever a perimeter door or window zone is violated The chime mode will not cause the RF3341 Wireless Keypad to chime Turning On the Chime Mode Enter your PIN code 4 2 3 4 Then enter To turn Off the Chime Mode repeat the above sequence
3. RF3341 Wireless Keypad User s Guide for the DS7400Xi Control Panel 1 0 General Information The RF3341 is a one way Wireless Keypad Transmitter with backlighting and key press sounder which allows the user to arm disarm and send special codes if programmed to do so by the installing company anywhere within the range of the system receivers The keypad can be wall mounted or portable Programming the Control Panel and the Panel Type determines what system functions are available from the Wireless Keypad The Keypads are programmed with a unique code which will allow only your keypad to work with your Security System These keypads are not weatherproof Do not leave outdoors CAUTION Although the range of the keypad may be up to 500 feet v4 150 meters in open air normal building materials can sail ie its range If use is anticipated in an IMPORTANT automobile or if the building has aluminum siding the range may be reduced even further It is recommended that the keypad be tested at various locations around the premises to verify the range v4 Avoid using the keypad in areas with significant metal or electrical wiring such as furnace rooms and utility rooms IMPORTANT 2 0 Features of the RF3341 Keypad when used with the DS7400Xi Conirol Panel The RF3341 can arm and disarm your alarm system The Keypad has an option key and three programmable ABC keys The functions of these keys are determined by you and your installing com
4. n your structure will be disabled You may move freely around the interior Perimeter Arming Occupied Entry Allowed Enter your PIN code 4 2 3 Then enter The perimeter doors and windows will now be fully armed unless programmed for an Exit Delay If so programmed the system will be fully armed when the Exit Delay period expires Opening any door will now start the entry delay Opening a window will cause an instant alarm The interior devices detectors in your structure will be disabled You may move freely around the interior ES Custom Arming Enter your PIN code 4 Then enter The system will now arm the pre defined areas unless programmed for an Exit Delay If so programmed the system will arm when the Exit Delay period expires Only your installing company can change the pre defined areas eae M Maximum Security Arming Full Arming No Entry Allowed Og Enter your PIN code 4 Then enter The system will now be fully armed unless programmed for an Exit Delay If so programmed the system will be fully armed when the Exit Delay period expires Violating any zone will cause an instant alarm Arming the System Force Arming Under certain conditions such as during an AC power failure or if some zones in your system are not ready Such as a window has been left open it may be necessary to Force Arm your system To Force Arm your system enter your
5. on the amount of use The recommended battery types are Duracell DL123A Sanyo CR123A or Panasonic CR123A Open the battery cover by pressing the latch on the back cover Do not remove the screws from the back cover Insert the new battery Be sure to observe the proper polarity Close the cover Do not remove these screws Supervision Jumper Do not remove or change the position of this jumper If moved your alarm system may display a keypad trouble warning FCC COMPLIANCE NOTICE This device complies with Part 15 of the FCC Rules and with RSS 210 of Industry and Science Canada Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesirable operation Changes or modifications not expressly approved by Bosch Security Systems can void the users authority to operate the equipment 03 04 RF3341 User s Guide P N 45572D Page 2
6. pany Option Key Cover for Programmable ABC Keys 3 0 Using the RF3341 Keypad The RF3341 can be used to arm and disarm your alarm system The Keypad cannot tell you if the alarm system is armed or disarmed If you will need to know if the system is armed or disarmed have your installing company install an indicator light or other device to show the system status The LED on the Keypad will flash to indicate that a signal has been sent To arm or disarm the system you must know your 4 or 6 digit Personnal Identification Number PIN code A PIN code is always required The following examples of arming and disarming will use a PIN code of 1234 Your PIN code should be different ii Security Systems 1 3 1 Arming Your System Normal Arming Full Arming Entry Allowed a Enter your PIN code 4 Then enter The system will now be fully armed unless programmed for an Exit Delay If so programmed the system will be fully armed when the Exit Delay period expires Opening an entry door will start the entry delay Violating any other zones will cause an instant alarm es Perimeter Instant Arming Occupied No Entry Allowed Enter your PIN code 4 2 3 4 Then enter B eA 2 The perimeter doors and windows will now be fully armed Opening any door or window will now cause an instant alarm The interior devices detectors i
Download Pdf Manuals
Related Search