User manual - Wassermann Dental
Contents
1. Important The unit should be switched off again using the advance interrupt 1x after the end of the additional sterilisation work Leave main switch on The steriliser switches itself on again automatically programmed weekly schedule 8 2 Automatic wax removal Wax removal takes place after the first sterilising process the sterilising time must be complete indicated by buzzer The removal time is 30 min The water temperature should be approx 85 C Sterilisation can continue during the cleaning phase Wax removal is interrupted automatically and resumed after the sterilising process listen for buzzer Proceed as follows for intermediate cleaning 1 Switch unit off 2 Set function switch to Automatic sterilising 3 Enter short sterilisation time e g 30 sec 4 Start program and allow to finish buzzer 5 Wax removal starts again Wax removal can be delayed if not needed 1 Change the selection switch to Automatic sterilising 2 Close the lid 3 Start sterilisation using the Start Stop button and stop it using the same button 4 Wax removal will occur after the next sterilisation process The removed wax runs into the waste tray in the base of the unit WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 9 Programming the activation computer The unit does not need to be on to change computer settings The clock does not need electrical power indicated by flashi2. cea a ea cea Ra S EEAS ESS 5 2 Set up Installation 5 3 Water supply 5 4 Fitting the spray wand m 5 5 6 STARTING THE CONTROLLER ina een Ty nera opea Lada PR 10 7 OPERATION E 10 7 1 General operating instructions 10 7 2 Filling the unit with water sa 12 7 8 12 7 4 18 7 5 214 7 6 Reading preset and actual time we 14 7 7 Reading the temperature setting 2 14 7 8 Automatic Sterilising 15 7 8 1 Sterilising using the manual spray head 2 16 7 9 Manual steriliSitiQ EE 16 8 MANUAL SPRAY HEAD OPERATION IN AUTOMATIC MODE 17 8 1 Exceptions in operation of steriliser 8 1 1 Advance Ausschalten is 8 1 2 Additiorial actiVallOn REQUE TE BENE eS aai ERU HEISE 8 2 Automatic wax removal REEE 9 PROGRAMMING THE ACTIVATION COMPUTER 19 9 1 Factory presets in auto mode display menu 19 9 2 Entering or changing the date and time Mode O 2 20 9 2 1 Changing the date 2 20 9 2 2 Changing the time 2 20 9 2 3 Overriding summertime changeover 21 9 3 Ent
3. completely main switch on 8 The remaining water can now be removed with the wax drain container lever vertical Process must be repeated several times as the container cannot hold all the remaining water Important Return drain lever to the horizontal after removing the remaining water 30 WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Before refilling the unit with water we recommend cleaning the interior and the pump filter The sensor probes right side next to pump inlet should also be cleaned Check for lime on the heater Cleaning the roller brushes is neither necessary nor advisable 11 2 6 monthly lime removal Intermediate lime removal may be needed depending on the build up Up to 500 ccm depending on instrument condition Drain water containing too much wax dissolver Mix Kalk Ex in cold water Warning Allow KALK EX max 12 hours to work Drain solution and rinse thoroughly Observe protective measures wear wraparound protective glasses and suitable gloves Avoid contact with skin eyes and clothing Do not swallow or breathe in lime remover Seek medical help Clean the outside of the unit with a sponge or soft cloth and mild detergent The model plate must always be legible and should not be removed 11 3 Servicing The WAPO EX 12 does not need any special servicing Just make sure it is kept clean and free of lime 11 4 Warranty The warranty period for our in
4. components are installed es WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 12 Technical data 170987 WAPO EX 12 Technical data Power 230 V 50 60 Hz Power consumption 12 Output 3300 Watt W x H without spray arm x D 650 x 900 x 620 mm W x with spray arm x D 650 x 1600 x 620 mm Weight 87 5 kg Water capacity approx 50 L Water feed rate 4 5L min Water drain height 470 mm Noise emission lt 70 dB A Li We reserve the right to make technical changes 33 WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 13 EC Compliance Certificate In accordance with 73 23 EWG low voltage guidelines modified by 93 68 EWG and 89 336 EWG guidelines and 89 392 EWG Machinery guidelines with modifications Manufacturer WASSERMANN Product description Wax steriliser for Dental Maschinen GmbH dental applications Rudorffweg 15 17 D 21031 Hamburg Model WAPO EX 12 USA 170986 WAPO EX 12 GB 170984 WAPO EX 12 AUS 170983 Applicable standards EN 61010 1 1993 A2 1995 EN 50081 1 EN 50082 1 DIN 45635 P 1 Hiermit wird best tigt dass die oben bezeichnete Maschine den genannten EG Richtlinien entspricht Diese Erkl rung wird ung ltig falls die Maschine ohne unsere Zustimmung ver ndert wird This is to confirm that the above mentioned machine complies with the described EC rules This declaration becomes invalid if the
5. must be fitted with a fuse 16 A 230 V SS WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 5 3 Water supply Insert the supplied feeder hose gasket in its seat Connect the hose to the tap Connect the drain hose to the outlet on the unit Make sure the hose it at a suitable height above the feeder pipe Warning The minimum amount of water should be about 4 5 L at a supply pressure of 0 2 max 10 bar 5 4 Fitting the spray wand Raise the coil until the screw fitting can be seen Warning In order to avoid injury be sure to take hold of the spacer to raise the coil Angle the head over the spray area and screw in the wand SH WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 5 5 Preparation As well as connecting the unit correctly the following tasks need to be carried out before you start up Remove both sliding covers Remove the denture moulds and sterilising channel Swing the spray arm up and remove Remove the large loose stainless steel basket Check that the pump filter is sitting correctly in place Remove remaining packaging Insert roller in bearing Note The roller carrier can only be inserted vertically in the vertical holder for the drive shaft Reinsert the large stainless steel basket Fitthe spray arm on the connecting joint and swing it down bayonet connector Make sure all seals are clean Insert the channel from the front so th
6. User manual Boil out Automat Wapo Ex 12 Wapo Ex 12 Die Basis f r Ihr Labor ots WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Dear customer Thank you for choosing a product from the Wassermann range Wassermann dental equipment incorporates the highest standards of quality and the latest technology In order to enjoy maximum performance and years of trouble free operation please read this user manual carefully before you start work and operate the unit according to the recommended guidelines Be sure to keep the user manual close at hand so it can be referred to at any time Company address Wassermann Dental Maschinen GmbH Rudorffweg 15 17 D 21031 Hamburg Germany Tel 49 0 40 730 926 0 Fax 49 0 40 730 37 24 Email info wassermann dental com URL http www wassermann dental com WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Contents 1 FEATURES 9 4 2 FOR YOUR E d 3 A 2 1 Eollow the usermahual ie nU tede a Sula 4 2 2 Safety guidelines ES 2 3 Responsibility for operation or damage seen 5 MEE 2 2 M 03 gpapeee e SEENEN 6 4 CONTENIS u 6 5 BEFORE YOU START e EE 7 5 1 Unpacking Transport 2
7. Warning do not use wax removers containing solvents as Drain solution and rinse thoroughly WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 11 Care and maintenance 11 1 Cleaning In order to guarantee problem free operation 1 x per week Remove cover f more than 34 full the waste wax container must be emptied This can be reused for less high quality work Reinsert container and replace cover Every 6 weeks The water may need changing earlier or later depending on use and water hardness We recommend every 6 weeks Wax removal should be carried out before changing the water to keep the amount of wax in the drain hose as low as possible This can occur early in the day 30 minutes before the unit switches off automatically The water temperature should be 85 Follow the steps below when changing the water 1 2 Unit must be heated to a water temperature of 65 Turn off tap and check drain hose is connected correctly to siphon or is hanging in wash basin 3 Set function switch to Pump down 4 Switch on pump with Start Stop button An audible tone low water level automatic heater switch off sounds while the container contents drains 60 seconds After pump down siphoned air will cause a gurgling noise the pump must be switched off with the Start Stop button 6 Reset function switch to Automatic sterilising position 7 Switch unit off
8. at any small particles can be caught in the mesh of the large stainless steel basket Swing the handle in again when reinserting the denture holders Fit sliding cover and close turn through 180 Remove cover magnetic mount on front of unit and close drain tap lever horizontal Insert the waste container under the drain tap Replace cover Open tap and check feeder hose for leaks i Leave a side clearance of 50 mm around the unit to allow adequate heat circulation The unit can be emptied using a siphon make sure the drain hose does not leak and is firmly attached to prevent it coming loose If there is no waste drain hang the hose in a washbasin WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 6 Starting the controller Insert plug in socket 230V 50 Hz Open tap Activate main switch green toggle switch The unit will fill automatically max 50 L The unit heats up immediately to its basic setting 65 C or to the last stored sterilising temperature When the desired temperature is reached the yellow LED goes out and the unit is ready for operation N Use heat resistant gloves when working with the WAPO EX 12 The WAPO EX 12 is protected against running dry if the water is too low orange LED A warning signal also sounds while the program is running li Remove the power plug if the unit is not to be used for a long period 7 Operation 7 1 Gene
9. c operation 9 6 Reading and changing switching times Modus 9 6 1 Reading switching status Call up the switching times from our example Follow the steps below to check individual times inputs Use the OK button 1x to return to starting mode AUTO Press the menu button 2x to go to Mode Use the OK button 1x to open Mode The free memory locations are shown Use OK or the lozenge to read all settings Example 06 00 The steriliser will switch on automatically at 06 00 ON on the first 3 days of the week Example 18 00 The unit will switch OFF automatically at 18 00 on the first 3 days of the week SES WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 9 6 2 Changing switching times In our example the Friday switch on time should be entered by changing the weekly schedule Only possible because the unit is to switch on at the same time on Monday Tuesday and or Wednesday 06 00 Proceed as follows Press the OK button 1x AUTO mode displays Use the menu button 2x and OK 1x to change to Mode The free locations 26 PL are displayed Use OK 1x to call up the switch on time of 06 00 You can now change this using the lozenge 1x Before you can enter a switch on time for Friday Day 5 must be marked with a bar in the weekly list Press OK 4x Day 5 flashes Press the lozenge 1x Day 5 is assigned a bar Press OK 8x all other setting must remain unchanged dis
10. ch on the top of the unit is used to select operating functions There are symbols for Automatic sterilising Manual spraying and Emptying the unit Pump down Pump down Manual spraying Automatic Sterilising Set the function switch to Automatic sterilising open the tap and switch the unit ON The water fills the container to working level and heats it to operating temperature automatically takes about 1 5 hours The operating temperature is 85 C 185 F Wax remover should be added once the operating temperature has been reached nominal 85 C Use the manual spray head for this Add 100 ml wax remover without solvent to the sterilising channel Set the function switch to Manual spray head and start it using the Start Stop button round green button on control panel End process using the Start Stop button Change the selection switch to Automatic sterilising Wax remover only needs to be added if the water is changed or water is lost depends on work load 7 3 Time and temperature adjustment The WAPO EX 12 is ready for use once the water temperature has reached 60 C pump can be switched on Settings above 99 C are not possible for safety reasons The sterilising time max 60 min and temperature max 99 C need to be set for both automatic and manual operation The control panel at the front of the unit is used for this 18 WASSERMANN DENTAL MASCHINEN Die Basis f
11. change from jet to spray If it is not used for a Li lengthy period the spray head may be hard to turn because of residual wax Release this wax by running hot water through the head Rectification work is possible in manual mode because it does not require the lid to be closed 8 Manual spray head operation in automatic mode Turning the function switch to Manual during automatic operation activates the manual spray head However manual sterilising time is separate from the automatic sterilising process Resetting the function switch to Automatic to continue automatic operation requires the lid to be closed Safety tip Resetting the function switch to Manual immediately releases A the spray stream 8 1 Exceptions in operation of steriliser Switch the small red button on the computer OFF or ON to interrupt the program manually ahead of time 8 1 1 Advance switch off The unit is on but not needed that day LED display on Press advance interrupt button 1x LED display off Your unit is switched off STANDBY Leave the main switch on 1 0 rocker switch on The steriliser switches ON again automatically programmed weekly schedule ns WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 8 1 2 Additional activation The program has switched the unit off but it is needed for a longer time LED display off Main switch ON The steriliser is reactivated using the advance interrupt button 1x
12. election Confirm with OK 1x the days of the week appear in the display in numbers from 1 Monday to 7 Sunday all underlined The bars show the days to which your programming applies Use 3x to change to week day 4 number flashes use the lozenge shaped button to remove the bar 1x Use OK 1x to select week day 5 and remove the bar Again use OK 1x to select week day 6 flashes and remove the bar with the lozenge Remove Sunday from your schedule Select day 7 with OK and delete the bar with the lozenge Confirm with OK Days 1 3 Monday to Wednesday are marked with bars a WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor switch on time can now be specified for these days flashing display 0 Use OK and the lozenge to set the switch on time 06 00 AON Press the OK button 1x Use the lozenge 6x to change the display to 06 Mit Taste OK 2x dr cken wird die Einschaltzeit auf 06 00 A angelegt durch die Rautetaste 1x wird der Eintrag ON angeh ngt Display 06 00 AON Confirm with OK Your equipment will switch on automatically at 6 00 You can now enter the Switch off time Use OK 3x to select week day 4 and remove the bar with the lozenge Deactivate days 5 6 and 7 inthe same way Use OK to change to the time 0 flashing Choose a switch off time Press lozenge 1x and change number to 1 Press OK and change to the next number change this with the
13. ering operating data menu mode PR and mode i2 9 4 Deleting switching times a 2 22 9 4 1 Deleting individual switching times 22022 9 4 2 Deleting all switching times wis 22 9 5 Programming a weekly schedule in PR mode wee 9 5 1 Input for several days 28 9 5 2 Entry for one day u uy een ea une 24 SES WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 9 6 Reading and changing switching times Modus 2 25 9 6 1 Reading switching status 9 6 2 Changing switching times 9 7 Holiday switching in PR mode 10 TROUBLESHOOTING 11 CARE AND MAINTENANCE u u uuu uuu uuu uu u 29 E Eege mE 11 2 6 monthly lime removal 11 8 Servicing 11 4 Warranty 11 5 Spare parts 11 6 X Repairs 12 TECHNICAL DATA 32 13 EC COMPLIANCE CERTIFICATE u 33 Ms WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 1 Features The famous Wassermann WAPO EX 12 wax steriliser with multifunction display is capable of sterilising wax for up to 12 denture halves Its long service life is due to a smooth running no seal bronze pump and a stainless steel housing The unit has a water level indicator to prevent overheating 2 For your safety 2 1 Follow the user manual You s
14. ge 2x OK 1x Lozenge 4x OK 2x Lozenge 4x Display 24 04 END OK 1x Lozenge 2x Important AOFF switch unit off Use OK 1x and the menu button 1x to return to AUTO mode It is very important to turn the tap to your unit off during holiday periods Otherwise it should only be turned off using the holiday switch 28 WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 10 Troubleshooting Problem Likely cause Likely solution WAPO EX 12 does not Not plugged in Check or insert mains plug heat Main switch not on Check and switch on if necessary Level sensor dirty Clean level sensor Water warning light Water level too low Fill with water until red LED comes on and audible goes out and warning tone signal sounds stops Water pump does Operating or preset Heat to operating min come on temperature not reached 60 C or preset temperature Multifunction display does Voltage variations in lines Switch main switch off then not work correctly 230V 50 Hz on again after approx 1 min Multifunction display Short circuit Contact Service shows F 1 shows F 2 shows A Multifunction display Temperature above 108 C Contact Service shows 8 Li If the above suggestions do not solve the problem get in touch with your dental depot or our Service staff these will attack rubber parts Warning allow KALK EX max 12 hours to work I
15. hould read and carefully follow the instructions in this user manual for setting up and operating the unit The device is intended only for its specified purpose Especially important points are highlighted as follows Warning A This is a warning of risk situations and dangers Failure to observe this warning could be life threatening These warnings must be observed Information Li This symbol draws your attention to specific features that must be observed oe WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 2 2 Safety guidelines This equipment is designed to operate at 230V 50 Hz A Make sure it is always connected to the appropriate power supply The rated output of the unit is 3300 W If a fixed connection is used the unit should be fitted with an all pin disengager Always remove the plug from the power socket before undertaking maintenance or cleaning work 2 3 Responsibility for operation or damage The responsibility for operating the device lies exclusively with the owner or user if said device is incorrectly serviced maintained or altered by persons not employed by an authorised dealer or if the device is used in a manner contrary to its specified purpose The unit must be maintained and operated in accordance with this user manual Wassermann Dental Maschinen GmbH is not responsible for damage arising from the nonobservance of these instructions Warranty and responsibility provisions contained in
16. is above the symbol time Press the OK button 1x The current date appears in the display You can now select individual positions to change using the OK button move right and the arrow button move left indicated by blinking display Change the value using the lozenge shaped button Use the OK button to quit the changed position the new value is stored To end entering the date press on OK until the word TIME appears in the display the current time is displayed 9 2 2 Changing the time You can now select individual positions to change blinking on the display using the OK button move right and the arrow button move left Change the value using the lozenge shaped button Use the OK button to quit the changed position the new value is stored To end entering the time press on OK until no further position is blinking in the display Auto mode is displayed all settings are stored The automatic changeover to summer time has already been programmed in accordance with the regulation applying since 30 05 1994 Start Last Sunday in March End Last Sunday in October al WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 9 2 3 Overriding summertime changeover Press the OK button 1x Press the menu button 4x until the dot in the display is above the S W symbol time Press OK 1x the word ON appears in the display summertime ON Press the lozenge shaped but
17. lozenge 8x to 8 display 18 Press OK 3x Display 18 00 A Use the lozenge 2x to enter OFF Display 18 00 A OFF Confirm with OK Your equipment will switch off automatically at 18 00 Use the menu button 1x to return to AUTO mode 9 5 2 Entry for one day In our example Thursday Press OK AUTO mode starting status Use the menu button 1x and 1x OK to switch to PR mode Bar chart for the week will display Use the lozenge to remove the bar under Day 1 Use OK to select day 2 and remove the bar with the lozenge Repeat to remove bars from days 3 5 6 and 7 Just leave Day 4 Thursday marked You can now set the switch on time m WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Enter the following for the time 0 flashing Press lozenge 1x and change number 0 to 1 Use OK to select again Use the lozenge 1 to change the display to 11 Use OK 1x and the lozenge 1x to set the display to 11 Use OK 1x and the lozenge 5x to set the time to 11 15 Conform with OK display A Use the lozenge 1x to change to 11 15 A ON Use the menu button 1x to store Your steriliser will switch on automatically at 11 15 The switch off time is programmed in the same way Just leave Day 4 marked Set the time as described above to 14 00 A Use the lozenge 2x to enter OFF display 14 00 A OFF Confirm with OK Use the menu button to return to automati
18. machine is modified without our approval Cette machine est conforme aux normes en vigueur de la Communit Europ ene Cet avis est nul et non avenant si cette machine est modifi e sans notre accord Esta maquina anteriormente mencionada cumple con los limites requeridos por el reglamento EC Ahora bien esta declaraci n quedar invalidada en caso de realizar modificaciones al aparato sin nuestra aprobaci n Hiermee wordt bevestigd dat bovengenoemde machine voldoet aan de voorgeschreven EU normen Deze verklaring verliest geldigheid als er zonder onze uitdrukkelijke toestemming wijzigen aan de machine worden aangebracht Place date Hamburg 17 March 2006 Company stamp Signed had bai ilfried Wassermann Managing Director 34 WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Notes SES WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Notes aD WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Notes 37 WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 38 WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor WASSERMANN DENTAL MASCHINEN Wassermann Dental Maschinen GmbH Rudorffweg 15 17 D 21031 Hamburg Tel 49 0 40 730 926 0 Fax 49 0 40 730 37 24 Email info wassermann dental com Internet http www wassermann dental com
19. ng display Six red selector switches are used for programming All entries are step by step The position to be changed blinks and can be changed using the lozenge shaped button The OK button is used to move to the next position and the arrow button to go back Input is finished when no position is blinking Use the CL button to delete activation times The menu button is used to select settings Button A manual button with symbol is used to switch the clock output channel on and off and is only used in exceptional cases 9 1 Factory presets in auto mode display menu Press the OK button All factory presets are shown on the display bar at the top tells you if your unit is switched on set at the factory for 6 am to 6 pm The current time is shown in the centre e g 10 22 The day of the week is shown under the time e g 4 Thursday The dot above the word Auto tells you which menu you are in currently Auto display menu The last message tells you whether the unit is on or off ON or A OFF This means for example 6 am AT ZON and from 6 pm A OFF These settings need to be adjusted to suit your operating conditions mene WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 9 2 Entering or changing the date and time Mode 9 2 1 Changing the date Press the OK button Auto mode displays Press the menu button 3x until the pointer in the display
20. oth at 6 00 am Delete using the CL button 30 PL free memory locations now appears in the display The factory settings no longer needed are deleted You can also delete all switching times but the date and time are retained 9 4 2 Deleting all switching times Press OK AUTO mode displays Press the menu button 2x into modus alter change Press OK 1x the free memory locations are shown on the display e g 28 PL Press the CL button CL 2x to delete all switching times 30 PL free memory locations now appears in the display 9 5 Programming a weekly schedule in PR mode There are two program modes for designing your own personal flexible weekly schedule You can enter switching times for one or more days The switch on point should be 90 minutes before work 4 WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor starts to allow the water sufficient time to heat up In our example the equipment is to be operated on the following days Automatic switch on from Monday to Wednesday at 6 am because work starts at 7 30 Automatic switch off at 6 pm end of working day Thursday from 11 15 automatic ON to 2 pm automatic OFF Friday from 6 am to 2 pm Saturday and Sunday not operated These days do not need to be programmed 9 5 1 Input for several days In our example from Monday to Wednesday Press OK AUTO mode starting status Press menu button 1x PR mode menu s
21. pening one or both lids will interrupt automatic operation Recontinue by closing one or both lids e g after visual checking If the Sterilising button flashes the lids are not closed There will be a delay of 1 minute while the heat returns to the previous level If the closed denture holders in the sterilisation unit are to be sterilised for a short time to make them easier to open gloves must be worn to avoid scalding 7 8 1 Sterilising using the manual spray head The following safety instructions must be followed for safe work with the manual spray Adjust the spray so that the spray holes are directed towards the channels Do not hold the manual spray head by the rose or hose Do not direct the spray at other people We recommend the use of gloves because of the high temperatures up to 95 C involved 7 9 Manual sterilising Set the function switch to Automatic Check or change the sterilising time and temperature Set the function switch to manual spraying and make sure that the manual spray head is aligned so that the spray openings in the head are directed at the sterilising channel For safety reasons the spraying process is started using the Start Stop button Spraying ends at the conclusion of the sterilising time or can be interrupted using the Start Stop button The function switch must now be changed back to Automatic EL WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Turn the spray head to
22. play shows 26 PL The unit will now switch on at 06 00 The Friday switch off time is the same as at the end of Thursday and is entered as follows In Mode select a switch off time for Thursday of 14 00 A L Press the OK button 3x Press the lozenge 1x then OK 4x Day 5 will flash on the display Use the lozenge 1x to insert a bar Press OK 8x to transfer all other entries Use the menu button 1x to return to AUTO mode The steriliser will now switch off on Friday at 14 00 d Important Each programmed or changed week day must have a switch on and switch off time All changes made apply to the days market with a bar SR WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 9 7 Holiday switching in PR mode Work pauses e g public holidays can be entered using holiday switching The unit should be shut down completely before longer holidays e g works closure Only one holiday program can be entered New entries overwrite the previous entry Once the holiday has passed the unit deletes the holiday program automatically and return to the weekly program Example Turning the steriliser off between 20 00 and 24 00 in April Displa Use the OK button 1x to return to starting mode AUTO Use the menu button 1x and OK 1x to change to PR mode Press arrow button 1x and enter start time lozenge 2x OK 3x Lozenge 4x y 20 04 START OK 1x Enter end time lozen
23. r Ihr Labor The function switch top of the unit must be turned to Automatic sterilising for all program settings including manual sterilising 7 4 Sterilising Time setting 1 Press time button 2 Press Preset button e 3 Press and hold the Time button then set the desired duration using the Preset button Temperature setting 1 Press Temperature button 2 Press Preset button e 3 Press and hold the Temperature button then set the desired temperature using the Preset button li All instructions for using the unit whether in verbal or written form are based on our own experience and experimentation and can only be regarded as guidelines SECH WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 7 5 Storing Set values can be stored by pressing the Sterilise m and e buttons simultaneously Storage is confirmed by a YES on the LED display Each time a value is stored the previous value is overwritten Warning lt is possible using the Sterilise A and e Reset buttons to revert to the factory settings 15 min and 65 C This is also confirmed by a YES 7 6 Reading preset and actual time Press Time button Press Preset the desired sterilising time will be shown on the display Press Actual the remaining sterilisation time after program start will be shown on the display 7 7 Reading the temperature setting Press Temperature bu
24. ral operating instructions The operator should ensure that only trained personnel use the steriliser special care should be taken with hot surfaces and liquids We recommend wearing heat resistant gloves Wax can be sterilised up to a melting point of approx 90 C 194 F The fully stainless steel unit is fitted with a low water detector to prevent overheating and subsequent damage An Aquastop ensures that the water supply is permanently on All information needed by the operator is indicated in the form of displays screens or LEDs or sometimes audible tones The capacity of 12 sies WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor denture halves or 8 large halves e g IVOCAPs and the sterilisation channel allow large numbers to be sterilised The programmable controller the automatic cleaning function and the flexible sterilising wand reduce downtimes e g heating up and facilitate manual sterilising and or cleaning and maintenance work The settings for temperature and time needed for the sterilisation process can be adjusted separately and are easily changed Before the unit can be operated the water tap must be open and the main switch in the ON position The tap should only be closed and the unit switched off if it is not to be used for long periods Do not forget to pull the plug Is WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 7 2 Filling the unit with water A function swit
25. struments is 12 months If faults occur within the warranty period contact your dental depot or get in touch directly with our Service department The steriliser should only be operated in perfect condition If faults occur which could harm operators or third parties the unit should not be used until it has been fixed The warranty does not cover damage caused by improper use external mechanical causes transport damage or interference with the unit by unauthorised persons S WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 11 5 Spare parts Spare parts Item no Name 830205 Denture container 830215 Filter set 170166 Combi sensor 170300 Button cover 326002 Spray head 511161 Rocker switch green 655001 Wax Ex 2 L 655002 Lime Ex 1 L 830093 Diffuser short 830094 Diffuser long 170005 Netword board new 170170 Micro Switch cpl 556012 thermo sensor 511213 Computer timer 830011 Water supply Aqua Stop 830135 Mixing unit cpl 830145 Spraying system 170320 Handshower bracket cpl 11 6 Repairs Repairs and maintenance of electrical components should only be undertaken by specialists or factory trained personnel who are aware of the safety guidelines Unplug the unit or disconnect the multi pin mains connection before opening any part of the unit Only original spares are to be used Responsibility for the product is voided if unauthorised persons alter it or if inappropriate
26. the sales and supply conditions of Wassermann Dental Maschinen GmbH are not extended by these instructions D Ensure that this user manual is accessible at all times and has been read and understood SES WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 3 Applications The WAPO EX 12 is suitable for sterilising wax for up to 12 denture halves 4 Contents Wapo Ex 12 automatic steriliser 170987 Spray wand 830145 2 L wax remover 655001 1 L lime remover 655002 Feeder hose with water inlet 830001 valve and gasket Drain hose with clamp 320061 322006 Stripper roller 830223 Plastic drain pan 390033 Sterilising channel 830220 Spray arm with seal 830160 2 denture containers 830205 2 covers 830230 1 User manual Ss WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 5 Before you start 5 1 Unpacking Transport Remove the packaging materials and set the unit up close to a tap with 3 2 external thread and a water supply Before transporting the unit ensure that it has been unplugged from the power socket Make sure that it is packed correctly in order to avoid accidental damage 5 2 Set up Installation Set the unit up where it is to be used not outside Make sure the water drain level is above 470 mm taking the following into account Height with spray wand 1600 mm Side clearance 750 mm Li Tip Install the unit under an extractor hood to remove the steam It
27. ton 1x the word OFF appears in the display summertime OFF Press OK to cancel the automatic changeover 9 3 Entering operating data menu mode PR and mode The operating data determines when your unit switches ON or OFF The switch on point should be selected 11 2 hours before work starts to be sure the water is hot enough set to 85 C 185 F at the factory On and off times are set in PR mode for a weekly period You can also program a holiday period in this mode for example bridge days Modus is used to change or delete these Your settings occupy 30 locations in memory The example illustrates programming operating data for a weekly period Press OK the factory settings appear in the display These settings must be deleted before a new weekly program can be entered the time and date are retained automatically fees WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 9 4 Deleting switching times 9 4 1 Deleting individual switching times 6 CH E Change to mode using the menu button 2x Press OK 1x the free memory locations are shown on the display e g 28 PL Use the arrow button to call up the current switching time Day 1 Monday to Day 5 Friday both at 6 pm Delete using the CL button 29 PL free memory locations now appears in the display Use the arrow button 1x to call up the current switch on time Day 1 Monday to Day 5 Friday b
28. tton Press Preset the desired sterilisation temperature will be displayed Press Actual the actual temperature will be displayed WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor i The WAPO EX 12 is ready for operation above 60 i e once the pump has started For safety reasons the program is set at the factory to switch the heating off automatically above 99 Risk of scalding A Do not hold the manual spray head by the rose or hose Do not direct the spray at other people Water coming from the spray head be at temperatures up to 95 C only direct the head towards the cover area or washbasin 7 8 Automatic Sterilising Change the selection switch to Automatic sterilising Insert the prepared denture halves in the holder marked places up to 6 items possible per holder Insert the holders in the guides and swing handle downwards Close lid For safety reasons both lids must be closed during sterilising Set the sterilising time and check the actual temperature Start using the Start Stop button e The yellow LED comes on during heating An audible signal sounds when sterilisation has ended The denture halves can now be removed Risk of scalding Wear temperature resistant gloves WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Note The automatic sterilisation process can be halted at any time using the Start Stop button O
Download Pdf Manuals
Related Search