Home

Hardware Installation - D-Link

1. Ring Enclosure e Manual and Software on CD e Screw Driver e Quick Install Guide Note Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product If any of the above items are missing please contact your reseller system Requirements Windows XP or Windows Vista At least 256MB of memory 512MB recommended An available Ethernet connection e Internet Explorer 6 x or higher VGA card resolution 800x600 or above e CPU 1 7GHz or above processor 2 8GHz plus processor with 512MB memory and a 32MB video card is required for multiple camera viewing and recording in IP surveillance program D Link DCS 6110 User Manual Section 1 Product Overview Introduction DCS 6110 Fixed Dome Network Camera is cost effective and an ideal security solution providing high quality real time videos in MPEG 4 and JPEG compression for small to medium sized businesses offices and homes The DCS 6110 features 3G mobile video support enabling you to view a live video feed from your camera on a compatible 3G mobile phone or PDA anywhere in your 3G coverage area The 3G mobile video support allows you to monitor a remote location without using a computer or an internet connection In addition supports dual stream output for simultaneous live monitoring and high resolution recording D ViewCam software is also included to manage up to 32 cameras simulta
2. Select your Dynamic DNS provider from the pull down menu Enter the host name of the DDNS server Enter your username or e mail used to connect to the DDNS Enter your password used to connect to the DDNS server Indicate the connection status automatically determined by the system D Link DCS 6110 User Manual Product Page DCS 6110 Firmware Version 1 00 Helpful Hints DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS HELP Wizard Network Setup Video Motion Detection Time and Date Event Setup DI and DO Logout The Dynamic DNS feature allows you to host a server Web FTP Game Server etc using a domain name that you have purchased http vww whateveryournameis com with your dynamically assigned IP address Most broadband Internet Service Providers assign dynamic changing IP addresses Using a DDNS service provider your friends can enter your host name to connect to your game server no matter what your IP address is Sign up for D Link s Free DDNS service at www DLinkDDNS corn if connecting through an IP DDNS SETTING Enable DDNS Server name www dlinkddns com Free w Host name default User name Password Confirm password Status Disconnect Save Settings Don t Save Settings 44 Section 3 Configuration Image Setup You may configure the color brightness and orientation settings of the video image Preview of the image wi
3. to the camera Hemove the customized setting from the Delete List For example When the range of allowed list is set from 1 1 1 0 to 192 255 255 255 and the range of denied list is set from 1 1 1 0 to 170 255 255 255 Only users IP located between 171 0 0 0 and 192 25 25 25 can access the Network Camera D Link DCS 6110 User Manual Product Page DCS 6110 Firmware Version 1 00 Network Setup T Allow List a EE EH Start IP Address The starting IP Address of the Dynamic DNS es ALLOW LIST Image Setup Video Start IP address Motion Detection End IP address Time and Date Delete allow list 1 0 0 0 255 255 255 255 Event Setup DENY LIST DI and DO Start IP address omiz m Logout End IP address setting from qe Alloy v List Delete deny list Deny List Start IP Address The TNI IP A of the de Sa on PEDE sion to access the of the camera permiss tO access video t er th 1 camera Delete Deny List o9 Section 3 Configuration DI and DO The I O connector provides the physical interface for digital output DO and digital input DI that is used for connecting such external alarm devices as IR Sensors and alarm relays to the network camera DI and DO Setting for both Digital input signal and digital output signal can be configured here Digital input trigger Please select from High or Low for dig
4. 10 25 28 DDNSC Username or email is empty Apr 8 10 25 28 init MStarting pid 608 console dev ttySO0 P ordi and Apr 8 10 32 16 RTSP SERVER Start one session IP 172 1 Apr 8 10 32 26 RTSP SERVER Stop one session IP 172 5 pd Apr 8 11 04 21 EVENT MGR reload config file Apr 8 15 09 17 RTSP SERVER Start one session IP 172 17 5 Apr 8 15 09 18 RTSP SERVER Stop one session IP2172 17 5 1 Apr 8 15 50 52 automount 2634 mount generic failed to ae 17 5 169 type smbfs on mnt auto i1 Apr 8 15 51 35 SYS Recording entry 0 stop Apr 8 15 51 36 EVENT MGR reload config file Apr 8 15 51 43 automount 2716 mount generic failed to mount 172 17 5 169 type gt Current Log The system log file that displayed by the system The content of the file reveals useful information about camera configuration and connectivity status after the camera boots up smbfs mnt auto i1 Apr 8 15 51 50 automount 2719 mount generic failed to mount 172 17 5 169 type smbfs on mnt auto i1 Apr 8 15 51 57 automount 2722 mount generic failed to mount 172 17 5 169 type smbfs on mnt auto ii D Link DCS 6110 User Manual 65 Section 3 Configuration D Link DCS 6110 User Manual Help Product Page DCS 6110 Firmware Version 1 00 DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS HELP Helpful Hints Live Video e Live Video e Setup Maintenance e Maintenance e Status Set
5. Link D ViewCam Enter admin as the default username and leave the password blank Click Kd OK to log into the system and access the Add Camera Wizard Note Please refer to page 48 in the D ViewCam user manual to change your password pH Click OK D Link DCS 6110 User Manual 70 Section 4 D ViewCam Installation Welcome to the Add Camera Wizard Use this wizard to add your cameras to the D ViewCam system Note Use the left or right arrow to navigate the wizard Add Camera Assign IP Assign Map Search Result Quick Settings Add More Congratulations Welcome Welcome to the Camera Wizard This wizard will go through the following steps 1 Allow you to choose Auto Discovery or the option to Add Manually a camera Click Next to continue 2 If Add Manually is selected you will be directed to input your cameras IP Address 3 If Auto Discovery is selected you will be prompted with a list of available cameras and the options to configure their nare and recording schedules 4 If any cameras were missed you will be able to select Add another camera or continue and finish the wizard Instructions au LB Please click Next and follow the on screen instructions to add your camera s Click Next D Link DCS 6110 User Manual 71 Section 4 D ViewCam Installation Choose which method to add your camera s You can choose Auto Discovery to automatically search for your camera
6. Link recommends that you rename your camera for easy accessibility You can then identity and connect your camera via this name Please click on Next button Click Next Configure the correct time to ensure that all events will be triggered captu red and scheduled at the right time Please configure the correct time to ensure that all events triggered captured and scheduled at the correct time and day and then click on the Next button Click Next to continue Current Time OF Jan 2008 01 35 53 Time one GMT 08 00 Las Vegas San Francisco Vancauver Enable Daylight Saving Daylight Saving Dates Month Week Dav of Week Time DST End Click Next D Link DCS 6110 User Manual 33 Section 3 Configuration If you have selected DHCP you will see a summary of your camera s settings Please note down all this information as you will need it for accessing your camera within the network Click Apply to save your settings Click Apply If you have selected PPPoE you will see a summary of your camera s settings Please note down all this information as you will need it for accessing your camera within the network Click Apply to save your settings Click Apply If you selected Static IP you will see a summary of your camera s settings Please note down all this information as you will need it for accessing your camera within the network Click Apply to save your settings Click Apply D Link DCS 6110 User Man
7. Settings SECURITY D Link DCS 6110 User Manual 45 Section 3 Configuration Mode Frame Size Maximum frame rate Video quality Video Two different settings for two video streams stream 1 and stream 2 can be configured here You may configure one setting for computer display and the other one for mobile display It can be either JPEG or MPEG4 In JPEG mode the video frames are independent However MPEG4 consumes much less network bandwidth than JPEG Three options exist for the sizes of the video display You can select between 176x144 352x240 or 640x480 It is recommended using 176x144 for mobile viewing and 640x480 for computer viewing 1 is the minimum value while 30 is the maximum value It is recommended choosing 30 for computer viewing and 5 for mobile viewing This limits the maximal refresh frame rate which can be combined with the Fixed quality to optimize the bandwidth utilization and video quality If the User wants to fix the bandwidth utilization regardless of the video quality choose Constant bit rate and select the desired bandwidth D Link DCS 6110 User Manual Product Page DCS 6110 Firmware Version 1 00 Network Setup Dvnamic DNS Image Setup Motion Detection Time and Date This section allows you to configure the video of your camera You can configure different settings depending on whether you are viewing content from a PC or a Mobile Phone PDA Save Setting
8. The Multicast address ranges from 224 0 0 0 to 239 255 255 255 or equivalently 224 0 0 0 4 Default port number is 5560 or please choose between 1024 and 65534 D Link DCS 6110 User Manual 42 Section 3 Configuration Multicast RTCP video port Default port number is 5561 or please choose between 1024 and 65534 Multicast RTCP audio port Default port number is 5563 or please choose between 1024 and 65534 Multicast TTL 1 255 Set a Time to Live TTL value for multicast packet please choose between 1 and 255 Unicast video transmission delivers a stream through point to point transmission multicast on the other hand sends a stream to the multicast group address and allows multiple clients to acquire the stream by requesting a copy from the Multicast group address The five ports can be changed between 1025 and 65535 The multicast RTP port must be an even number and the multicast RTCP port is multicast RTP port number plus one and thus always be odd When the multicast RTP port changes the multicast RTCP port will change accordingly D Link DCS 6110 User Manual 43 Section 3 Configuration Enable DDNS Server Name Host Name Username Password Status Dynamic DNS DDNS Dynamic Domain Name Server will hold a DNS host name and synchronize the public IP address of the modem when it has been modified The username and password are required when using the DDNS service Click to enable the DDNS function
9. compliance Motion detection weekly schedule e Support Full Duplex operations e Upload snapshots video clips via email e 802 3x Flow Control support for Full Duplex mode e Upload snapshots video clips via FTP Supported IEEE 802 3af standard PoE D Link DCS 6110 User Manual 83 Appendix C Technical Specifications SYSTEM REQUIREMENTS Operating System Microsoft XP Vista Browser Internet Explorer Firefox Netscape Mozilla Opera browser SUPPORTED PDA MOBILE PHONES amp SOFTWARE Handsets with 3GPP player e Packet Video Player 3 0 e QuickTime 6 5 e Real Player 10 5 OPERATION TEMPERATURE 0 to 40 C 32 to 104 F STORAGE TEMPERATURE 20 to 70 4 to 158 F HUMIDITY e 20 to 80 non condensing EMISSION EMI SAFETY amp OTHER CERTIFICATIONS e FCC e CE e C Tick The mobile device must have support and subscribe to 3G service from the phone service provider The playback device must be equipped with 3G video playback such as RealPlayer or PacketVideo D Link DCS 6110 User Manual 84
10. develop a variety of security applications that are triggered on alarm based events The Network Camera provides an industry standard in out external connector for connectivity Note Use of video equipment for recording the image of a person without their knowledge and consent is prohibited in certain states or jurisdictions Nothing herein represents a warranty or representation that the D Link product provided herein is suitable for the end user s intended use under the applicable laws of his or her state D Link disclaims any liability whatsoever for any end user use of the D Link product which fails to comply with applicable state local or federal laws D Link DCS 6110 User Manual 7 Section 1 Product Overview Hardware Overview Connections DC Power Connector The DC power input connector is located on the side panel of the DCS 6110 labelled 12VDC with a single socket to supply power to the network camera lt Reset Ethernet Ethernet Cable Connector PoE The network camera s side panel features an RJ 45 connector for connections to 10Base T Ethernet cabling or 100Base TX Fast Ethernet cabling This network port supports the NWay protocol allowing this network camera to automatically detect or negotiate the transmission speed of the network The Ethernet port can also be used to power the camera by using a PoE switch Reset Button Heset is initiated when the reset button is pressed once and held until the p
11. it is an ideal protocol for transmitting real time video data which can tolerate some lost packets UDP Unicast Will stream to a single computer Product Page DCS 6110 Firmware Version 1 00 DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS HELP Live Video Helpful Hints Snapshot Here you can configure the audio and video settings as well as the type of connection your camera uses Stream Options This Client Setup when viewing it on a network aa Logout Save Settings Don t Save Settings STREAM OPTIONS n fi Pac E stre t the Set o and Aur Setu Stream1 OStream2 d Audio 5 Vic c the vith syni PROTOCOL OPTIONS O UDF unicast or e Audit ly Stream UDP Multicast Will stream to multiple computers using multicast O UDP multicast TCP OHTTP Audio data only Protocol Options e UDP Protocol This TCP Provides higher quality video streaming than UDP does It provides error correction and guarantees packet to be delivered to client However transmission speed will be reduced HTTP Protocol Offers the highest image and video quality However packet losses will diminish image quality when bandwidth becomes restricted If the network is protected by a firewall and it opens HTTP port 80 only HTTP protocol must be selected In UDP connections will not be available to remote users if all four ports have not been forwarded as shown on page 37 Only the HTTP port must be forwarde
12. password Please enter the username and password provided by your ISP Internet Service Provider to connect to Internet by PPPoE Click Next NEM D Link 069 6110 User Manual 17 Section 3 Configuration Check the Get IP by DHCP Server automatically box to obtain a new IP Dy irstalation Wizard 2 SEP VEU BR address every time the camera starts up Click Next to continue D Link Step 1 gt gt System IP address 192 168 1 128 Subnet mask 255 255 255 0 Default gateway 192 168 1 1 Primary DNS server 168 95 1 1 Secondary DNS server 1 68 192 1 1 Click Next Select UPnP Port Forwarding if your router supports this function If ad not choose Manual to manually enter your port numbers Click Next If your device is located behind the router and you want to access it on n Internet your router must be configured UPnP Universal Plug and Play to CO nti U technology will configure your router automatically if your router supports it If your router does not support UPnP port forwarding you need to configure the port numbers manually The wizard has detected that your router does not support UPnP port forwarding Choosing the Manual Advanced radio button is recommended and please also remembering to configure the port numbers in your router if you want to access the device on Internet UPnP port forwarding Manual port mapping HTTP port 80
13. password Modify a password for the administrator s setup Add user account Username Password Privilege Manage user Authentication Camera Name account Add new user account The username for the new account The password for the new account The access right for the new user Managing the accounts for the existing users The access right for the existing users Create a unique name for your camera and you can access the camera using this name in your web browser For example http DCS 6110 By default D Link DCS 6110 User Manual Product Page DCS 6110 Firmware Version 1 00 DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS HELP Helpful Hints You can change to camera s administrative password as well as adding more user accounts for accessing the camera co Logout ADMIN PASSWORD SETUP Device Management Backup and Restore Firmware Update Password Retype password can event that they are for gotten Add user account Add new user account ADD USER ACCOUNT User name Username The username for the new account Password Confirm password Password The passworc p for the new account Administrator O Normal User O Guest Administrator can configure all the setup Operator can use PTZ function and set preset position but can not enter abc M setup page Privilege e Privilege The access right for the new us
14. s or choose Add Manually to add your camera s via the camera s IP address Click Next to continue If you choose Auto Discovery the system will search all cameras that are located on the same LAN with same subnet The system will place all the cameras at the default map called My Map Click Next to continue If you choose Add Manually enter the IP address or domain name http port model name camera ID and password Click the button to auto detect the camera s model name then the model name will appear in the Model Name box Click Next to continue D Link DCS 6110 User Manual Add Camera Please select the add method for your cameras f Auto Discovery t Add Manually Auto discovery result The detected cameras are grouped under My EI My Map A a OCS 5300 55 Bd DCS 5220 233 Bd DCS 5220 234 Assign IP Camera IP Address o 2 Device Port B00 Model Name Camera ID FO Camera Password 72 Section 4 D ViewCam Installation D ViewCam shows the detected network camera s information You can choose and schedule the recording for each camera e 24 7 Continuous Recording Continuously records surveillance 24 hours a day 7 days a week e 24 7 Motion Detection Recording Continuously monitors but only records surveillance when motion is detected e Office Hours Only Continuously monitors during office hours 8 00AM to 6 00PM and only records when motion is detected e Non Offic
15. the Installation Wizard to return the DCS 6110 to a normal state 2 Wait for the LED on the front of the camera to blink red and green and hold the button for 30 seconds 3 Withdraw the tool after the second cycle of the LED blinking and a factory restore has been completed D Link DCS 6110 User Manual 81 Appendix B External I O Port External 1 0 Port DI DO Diagram 12V Pin 1 4 are used to connect with digital input and digital output devices Refer to the following illustration for connection method The DCS 6110 provides a general I O terminal block with one digital input and one relay switch for device control The relay switch of pin 1 and pin 2 can be used to turn on or off the external device Pin 3 and pin 4 can be connected to an external sensor and the state of voltage will be monitored from the initial state LOW 12V The I O connector provides the physical interface for digital output DO and digital input DI that is used for connecting a diversity of external alarm devices to the Network Camera such as IR Sensors and alarm relays 4 Ground I O Terminal Block 1234 OJololo External 1 0 Port The digital input is used for connecting external alarm devices and once triggered images will be taken and e mailed 1 Power 2 Digital Output 3 Digital input DI 4 Ground DI D Link DCS 6110 User Manual 82 Appendix C Technical Specifications Technical Spe
16. within your home network Click Next to continue Click Next If you have selected PPPoE enter your username and password Click Next to continue Click Next D Link DCS 6110 User Manual Please select whether your camera will connect to the Internet with a DHCP connection or Static IP address If your camera is connected to a router or you are unsure which settings to pick D Link recommends that you keep the default selection af DHCP connection Otherwise click an Static IP address to manually assign and IP address before clicking on the Next button C DHCP O PPPoE Static IP Client IP address 192 168 0 100 Subnet mask 255 255 255 0 Default Gateway 192 158 0 1 Primary DNS 192 158 0 1 Secondary DNS Please enter your ISP Username and Password This will be the case if your ISP uses PPPoE Contact your ISP if you are unsure User name Password OO Confirm password 32 Section 3 Configuration If you have a Dynamic DNS account and would like the camera to update your IP address automatically enable If you have a Dynamic DNS account and would like the camera ta update your IP address automatically enable DONS and enter in your hast information below Please click on the Next DDNS and enter your host information Click Next to button to continue continue Enable DONS Hast name name Password Confirm password Click Next Enter a name for your camera and click Next to continue D
17. 80 RTSP port 554 RTP video port 5556 RTCP video port 5557 RTP audio port RTCP audio port Click Next D Link DCS 6110 User Manual 18 Section 3 Configuration Click Next to continue Enable DDNS Server name Host name E mail address Key Confirm key Click Next gt gt Ports Step 4 gt gt DDNS Step 1 gt gt System Step 2 gt gt Network Setting Step 3 Registration Information www dlnkddns com Free myIPcam Sign up for D Link s Free DDNS server at http www DLinkDDNS com Dynamic DNS Domain Name Service is a method of keeping a domain name linked to a dynamic public IP address In many cable DSL connections a dynamic public IP address is assigned for every connecting request You can setup your DDNS service here and the device will automatically update your DDNS host name if the public IP address is changed Mobile Access Setup E A window will pop up asking you if you want to access the DCS 6110 via mobile phone Clicking Yes will set the video resolution to 176x144 D Link DCS 6110 User Manual Section 3 Configuration Click Apply to apply the settings listed in the window to the device Application may take a few minutes to process Step 1 gt gt System Step 2 gt gt Network Setting Step 3 gt gt Ports Step 4 gt gt DDNS Step 5 gt gt Apply Please check the f
18. C mount lens it is not changeable Drop ceiling bracket is another alternative option for an installation method In addition this network camera supports the Universal Plug n Play feature which allows computers running on Windows 2000 XP Vista to automatically recognize the camera and adds it to the network Sign up with one of the free Dynamic DNS services available on the web to assign a name and domain to the camera e g mycamera dlinkddns com This allows users to remotely access the camera without having to remember the IP address D Link DCS 6110 User Manual 6 Section 1 Product Overview e Supports a Variety of Protocols The DCS 6110 supports a wide variety of protocols such as RTSP FTP SMTP NTP and HTTP In addition it supports UPnP and DDNS DDNS allows your camera to be accessed using a static host name rather than an IP address UPnP allows Windows XP Vista users to easily find and connect to the camera e Web Configuration Using a Web browser administrators can configure and manage the network camera directly from its own Web page via Intranet or Internet Up to 20 user with unique names and passwords are permitted with the privilege settings controlled by the administrator e Connection to External Devices Supporting auxiliary Input Output connectors you can connect the Network Camera to a variety of external devices such as IR sensors switches and alarm relays Combined with programmable alarming equipment you can
19. DCS 6110 Version 1 1 Fixed Dome Network Camera User Manual Table of Contents Table of Contents Product Overview nece ee eere nnne nnne Event 5 1 51 Package POG SCN CF 53 SYSTEM Requirements 4 Add Media NE TEE PO T 54 Introduction 5 Ada EEE EEES 57 Wl ce 6 Add Recording 58 Hardware Overview 8 PRC CC SS 59 CONNECTIONS ccceceeeecceeeceeeseeeteeeteeeteeeteneeaneess 8 DO m 60 E N E Maintenance ayscaienes catpomeneecewonvetcntnonscursereeeenceuiemstencess 61 Hardware Installation 10 Device 61 Backup and Restore 62 Software Installation 12 Firmware Update 63 SA 64 Live Video E 26 64 ie Woo 65 MAP NO reni tun 28 66 Client Setup 0 ccc cecec cece eeeteeeteeeeeeesseeteeeteeeee
20. E mail Address Server address Server port User name Password Server address Server port User name Password Remote folder name Passive mode OHTTP URL User name Password Network storage Network storage location for example my_nas disk folder Workgroup User name Password Primary WINS server Secondary WINS server Test Save Settings Don t Save Settings test abc com test2 abc com mail abc com 25 http Helpful Hints Server name The unique name for server ne Email server Sender email address The email address of the sender Recipient email address The email address of the recipient FTP server Remote folder name Granted folder on the external FTP server The onform to tha transmission HTTP server URL The URL to upload the media Network storage Only one network storage is supported Network storage location The path to upload the media Workgroup The workgroup for network storage o3 Section 3 Configuration Add Media Up to 5 media for recording with its own settings can be created and configured here There are three types of media snapshot Video Clip and System Log Media Name Snapshot Source Send pre event image s 0 7 Send post event i
21. HELP Helpful Hints If you are an advanced user nfigured a IP ra be click t Connection Setup Wieard to input all the Internet Connection Setup Wizard Manual Internet Connection Setup ettings manuals In this section you can setup the camera s Motion Detection settings If you are configuring this device for the first time D Link recommends that you click the Setup Wizard button and follow the instructions on screen If you wish to modify or configure the Motion Detection manually click manual setup to enable the Motion Detection setup If you are an advanced user and you want to manually set up motion detection settings click Motion Detection Setup Wizard to input all the settings manually Motion Detection Setup Wizard Manual Motion Detection Setup This wizard will guide you through a step by step process to configure your new D Link Camera and connect the camera to the Internet Click Next to continue Click Next D Link DCS 6110 User Manual This wizard will quide you through a step by step process to configure your new D Link Camera and connect the camera to the internet To set up your mation detection please click Cancel to clase this wizard Otherwise click Next ta begin Step 1 Setup LAN Settings Step 2 Setup Internet Settings Step 3 Setup DONS Settings Step 4 Camera Mame Settings Step 5 Setup Time zone 30 Section 3 Configuration Select DHCP if you are unsure which settings to pi
22. PoE OFF DDNS ON D Link DCS 6110 User Manual Section 3 Configuration Logs This page displays the log information of your camera You can configure a remote log server so that you can view your log details remotely Enable remote log Enabling this feature so that the camera can send Frmware Version 1 00 camera log files to a remote server Log server settings Configure the setting for the log server Sm wo 5 NNNCNUMN device Info Helpful Hints iew a summary of device information here Enable remote log IP Address The IP address of the remote server ERE s5 checked can send lag message to remote log REMOTE LOG server v Enable remote log IP address remote log Port The port number of the remote log server The address 172 18 6 265 Port the default port is default port is 514 Sia va reed paa Save Save the setting CURRENT LOG Apr 8 10 25 10 syslogd 1 4 1 restart Apr 8 10 25 15 UPnPIGDCP Search IGD failed ffffffff Apr 8 10 25 16 DRM Service Starting DRM service Apr 8 10 25 25 SYS Serial number 001CF0784470 Apr 8 10 25 25 SYS Stem at Tue 4pr 8 10 25 25 UTC 2008 o epi 20 825 285 CT PTE aera Apr 8 10 25 25 NET DNS 192 168 168 250 Apr 8 10 25 26 SYS Recording entry 0 stop Apr 8 10 25 26 SYS Recording entry 1 stop Apr 8 10 25 27 EVENT MGR reload config file Apr 8
23. an Ethernet cable which will provide both power and data transmission over a single cable D Link DCS 6110 User Manual 11 Section 2 Installation Software Installation Turn on the computer and insert the D Link DCS 6110 Autorun CD into the CD ROM drive The following step by step instructions displayed are shown when using Windows Vista operating system The steps and screens are similar when using other Windows operating systems CO Click on Installation Wizard to begin software installation D ViewCam View Documentation Network Magic Support Registration DCS 6110 Business Class Networking 1 0 2 Setup The Installation Setup Wizard window will pop up Click Next to continue Welcome to the InstallationWizard 2 1 0 0 2 Setup Wizard This wizard will quide you through the installation of InstallationWizard 2 1 0 0 2 Itis recommended that you close all other applications before starting Setup This will make it possible to update relevant system files without having to reboot your computer Click Next to continue 12 Click Next D Link DCS 6110 User Manual Section 2 Installation Click Agree to accept the License Agreement Please review the license terms before installing Installation Wizard 2 1 0 0 2 Press Page Down to see the rest of the agreement End User License Agreement IMPORTANT READ CAREFULLY This End User License A
24. ault value is 8080 Port After you have enabled the Authentication you will need to configure and use the access name to access your video file For example http camera ip video mjpg video mjpg is the Access name you can modify it here Access name for The default name is video mjpg stream1 Access name for The default name is video2 mjpg stream2 Access name for stream 1 Access name for stream 2 The access name is used to differentiate the streaming source When using Mozilla Firefox or Netscape to access the Network Camera and the video mode is set to JPEG users will receive continuous JPEG pictures This technology known as server push allows the Network Camera to feed live pictures to Mozilla Firefox and Netscape Use http lt ip address gt lt http port gt lt access name for stream1 or stream2 gt to make connection For example when the access name for stream 1 is set to video mjpg 1 Launch Mozilla Firefox or Netscape 2 Type the URL command in the address field Press Enter 3 The JPEG images will be displayed in your web browser Port Default port is 21 If you want to change the port number you will need to specify the port when connecting to the FTP server For example FTP 68 5 1 81 60 if you use port 60 for your FTP server RTSP Streaming This setting enables you to connect to a camera by using streaming mobile device s such as a mobile phone or PDA Authentication Choose either Basic wh
25. cifications NETWORK PROTOCOL SUPPORT PHYSICAL amp ENVIRONMENTAL e TCP IP RTSP RTP RTCP HTTP SMTP FTP NTP DNS DHCP UPnP DDNS DIAGNOSTIC LED PPPoE ICMP Samba client IP Filtering 3GPP e 2 color LED e 3 AXIS ANGLE BUILT IN NETWORK INTERFACES e X 350 Y 45 Z 350 e 10 100BASE TX Ethernet port POWER INPUT VIDEO ALGORITHM SUPPORT e 100 240VAC 50 60Hz 12VDC 1 25 e JPEG for still image e MPEG4 MJPEG dual format compression POWER CONSUMPTION e Max 3 6 W VIDEO RESOLUTION e Up to 30fps at 176 x 144 DIMENSIONS e Up to 30fps at 320 x 240 194 W X 180 D X 107 H mm e Up to 30fps at 640 x 480 WEIGHT VIDEO FEATURES 1 39165 Adjustable image size and quality e Time stamp and text overlays SECURITY e 3 configurable motion detection windows e Administrator and user group protected Flip amp mirror e Password authentication VIDEO BIT RATE SURVEILLANCE SOFTWARE FUNCTIONS e 20K to 4M e Remote management control of up to 32 cameras e Viewing of up to 32 cameras on one screen CAMERA SPECIFICATIONS e Supports all management functions provided in web interface e VGA Progressive CMOS Sensor e Scheduled motion triggered or manual recording options e 1 5 Lux F1 4 e Electronic rolling shutter REMOTE MANAGEMENT e 3 7 12mm vari focal lens F1 4 F2 8 e Configuration accessible via web browser e Take snapshots video clips and save to local hard drive or NAS via web browser LAN e IEEE 802 3 compliance SURVEILLANCE IEEE 802 3u
26. ck Click Next to continue and skip to page 32 Click Next Select PPPoE if the camera is directly connected to the Internet through a DSL modem and the ISP Internet Service Provider requires you to use PPPoE for the Internet connection Click Next to continue and skip to otep 2 on page 31 Click Next D Link DCS 6110 User Manual Please select whether your camera will connect to the Internet with a DHCP connection or Static IP address If your camera is connected to a router or you are unsure which settings to pick D Link recommends that you keep the default selection af DHCP connection Otherwise click an Static IP address to manually assign and IP address before clicking on the Next button DHCP PPPoE Static IP Client address subnet mask Default Gateway Secondary DNS Po Please select whether your camera will connect to the Internet with a DHCP connection or Static IP address If your camera is connected to a router or you are unsure which settings to pick D Link recommends that you keep the default selection of DHCP connection Otherwise click an Static IP address to manually assign and IP address before clicking on the Next button DHCP PPPoE Static IP Client IP address Subnet mask Default Gateway Primary DMS Secondary DNS 31 Section 3 Configuration Select Static IP if your Internet Service Provider has provided you with connection settings or you wish to set a static address
27. d for RECORD OPTIONS Browse Folder c Record File Name Prefix CLIP Add date and time suffix to file name Save Settings Don t Save Settings Record Option e F elect target Default folder fol system will use serial number for file name remote users to make an HTTP connection video only Record Options Allows the user to specify a destination folder and prefix filename for the recorded video D Link DCS 6110 User Manual 29 Section 3 Configuration Setup Wizard To quickly configure your network camera click Internet Connection Setup Wizard or click Manual Internet Connection Setup to manually configure your network camera To quickly configure your network camera s motion detection settings click Motion Detection Setup Wizard and skip to page 34 If you want to enter your settings without running the wizard click Manual Motion Detection Setup and skip to page 46 internet Connection Setup Wizard Product Page DCS 6110 Firmware Version 1 00 DCS 6110 In this section you can setup the camera s wired and wireless network interface settings If you are configuring this device for the first time D Link recommends that you click the Setup Wizard button and follow the instructions on screen If you wish to modify or configure the camera settings manually click manual setup to enable the Camera connection setup LIVE VIDEO SETUP MAINTENANCE STATUS
28. daress To begin setup single click on the DCS 61 10 located in the camera list and click Manual Setup located on the left of the Installation Wizard Click Manual Setup D Link DCS 6110 User Manual Manual Setup Refresh Devices Access Information Firmware Upgrade Restore Default About IP Camera Installatic MAC 00 0D 88 7E 53 DF 00 02 D1 05 03 0A IP Address 192 168 1 187 192 168 1 128 Model DCS 6620G Please check the MAC and model name in the product label of your device first Then you can start to link to your device and show the main screen by double clicking the item in the above selection list If you are not able to find your device in the above selection list please make sure all cables are properly connected to your device and then click on the Refresh Devices button Model No DCS 3415 P N BCS34 15ANA Al S N D5BXXXXXXXXX C MTNA TONNE MAC XX 277 HN MAN Wee XX FAN Ver X XX asuata POC BROOM wea uec ient vm Ub 7 eee Comme 3 Sub fe morang wA Cordis CUTE Monde Pay You can find the product label in the rear bottom part of your device 15 Section 3 Configuration Enter a password and confirm the password for the admin ID and click Next Note The default administrator username is admin and the password may be left blank The passwo
29. ddresses The Fixed Dome Network Camera can be connected to a LAN with private IP addresses 9 Can the Fixed Dome Network Camera be installed and work if a firewall exists on the network If a firewall exists on the network port 80 is open for ordinary data communication The DCS 6110 uses port 5002 for streaming audio and port 5003 for streaming video These ports or the ports you have specified in the Setup Tab in the Configuration screen need to be opened on the firewall D Link DCS 6110 User Manual 76 Section 5 Frequently Asked Questions 6 Why am I unable to access the Fixed Dome Network Camera from a web browser If a router or firewall is used on the network the correct ports for the DCS 6110 may not be configured on the router or firewall To correct the problem you need to determine if the DCS 6110 is behind a router or firewall and if the router or firewall is properly configured for the ports the DCS 6110 is using Refer to Page 28 for help in opening the correct ports on a router or firewall for use with the DCS 6110 Other possible problems might be due to the network cable Try replacing your network cable Test the network interface of the product by connecting a local computer to the unit utilizing a Ethernet crossover cable If the problem is not solved the Fixed Dome Network Camera might be faulty T Why does the Fixed Dome Network Camera work locally but not externally e This might be caused by network firewall pro
30. digital input trigger here and arrange the detection Priority The event with schedule at the same time higher priority will be Save Settings Don t Save Settings Delay second s before detecting next event ee The delay to check next Motion Detection event It is used in motion ae p detection and digital input Time and Date trigger type Event name Motion Detection Enable this event There xc hak Erde of igger s ted Access List Priority normal trigger su DI and DO Delay for 10 seconds before detecting next event For motion detection and digital input Video motion detection Select the windows which Logout orei TRIGGER Periodic The event is triggered in specified intervals The unit of Video motion detection trigger interval is minute Detect motion in Test Note Please configure Motion Detection first O Periodic triggered when tne D status changed by externa Trigger every 1 minutes device System boot The event System boot is triggered when the system boot up EVENT SCHEDULE Sun v Mon v Tue v wed v Thu v Fri v sat me shos Time input the tim Always From to 24 ACTION Trigger D O for 1 seconds Server1 Attached media Snapshot v NAS Attached media Snapshot v event is triggered Save Settings Don t Save Settings SECURITY 57 Section 3 Configuration Add Recording He
31. e For example fies if each recording file is 6MB and the total cycling recording size is 600MB then camera will recording 100 files to the specified location folder And then the camera will delete the oldest file and create new file for cycling recording Please notice that if the HDD empty space is not enough the recording will stop Before you setup this option please make sure you HDD have enough space and it is better not to save other files in the same folder as recording files Size of each file for File size for each recording file You may input the value in the range of 200 6000 recording File Name Prefix The prefix name will be added on the file name of the recording file s D Link DCS 6110 User Manual 58 Section 3 Configuration Access List Here you can configure the access permissions for each user Allow list The list of IP addresses that have the access right Start IP address End IP address Delete allow list Deny list Delete deny list to the camera The starting IP Address of the devices such as a computer that have permission to access the video of the camera Click Add to save the changes made Note A total of ten lists can be configured for both columns The ending IP Address of the devices such as a computer that have permission to access the video of the camera Hemove the customized setting from the A low List The list of IP addresses that have no access right
32. e Hours Only Continuously monitors during non office hours 6 00PM to 8 00AM and only records when motion is detected Note Excluding 24 7 Continuous Recording all other schedule recording modes can only record when motion is detected Please refer to the user manual for more information on Click Next to continue Quick Settings The discovered cameras information showed as below i Camera Name M Schedule Recording Type DCS 5300 55 DCS 5300 None DCS 5220 233 DCS 5220 Mone DCS 5220 234 DC3 5220 None D Link DCS 6110 User Manual Status Active Active Active IP Address 10 1283 1 55 10 1281 233 10 123 1 234 MAC Address Dapgpeszpspca4 0013460 C 3BC3 00123460 E 3BEB 73 Section 4 D ViewCam Installation Select Yes to add other camera s or select No if you have no additional Add another camera camera s to add Click Next to continue C Yes Ma The Add Camera wizard is now complete Click Close to access the D ViewCam s main screen Congratulations Congratulations your camera configurations now complete and ready ta use Tou now click the Clase button to view your camera and configure any additional advanced settings Your D ViewCam Installation is Complete Note Please refer to the D ViewCam user manual for information about using D ViewCam D Link DCS 6110 User Manual 74 Section 5 Freq
33. e controller left and right until the desired range is R achieved tighten the zoom controller once completed oF Loosen the focus controller and adjust the focus range by x ni i EN Bm R moving the controller left and right until the image is clear EM o em All p tighten the focus controller once completed a a a lt a gt cu D Link DCS 6110 User Manual 23 Section 3 Configuration Attaching the Enclosure Once the lens is properly adjusted rearrange the light shield so that it will not obstruct the lens during surveillance Place the dome enclosure over the network camera so that the LED sticker on the dome enclosure is properly aligned with the camera s LED Insert the supplied screws into the two holes located at the base of the dome enclosure tighten until secure Place the ring enclosure over the dome enclosure Once placed gently turn the ring enclosure clockwise until it locks and is securely attached to the dome enclosure Note When attaching the ring enclosure be sure to first align the line on the ring enclosure with the triangle on the dome enclosure When attachment is successfully made the line on the ring enclosure will be aligned with the line on the dome enclosure D Link DCS 6110 User Manual 24 Section 3 Configuration Web based Configuration Utility This section will show you how to configure your new D Link Network Camera using the Web based Configura
34. e name VIDEOS20080104 100341 T 1 File name prefix Date and time suffix The format is YYYYMMDD HHMMSS D Link DCS 6110 User Manual 56 Section 3 Configuration Add Event Up to 3 events with its own settings can be created and configured here Meanwhile you can schedule the events here Event name Unique name for the event Enable this event Select this to activate this event Priority Set the priority for this event and the event with higher priority will be executed first Delay The delay time before checking next event It is being used for both events of motion detection and digital input trigger Trigger The input type that triggers the event Video motion Motion is detected during live video monitoring Select detection the windows that need to be monitored Periodic The event is triggered in specified intervals The unit of trigger interval is minute Digital input External trigger input to the camera System boot The event is triggered when the system boot up Time Select Always or enter the time interval Trigger D O Check it to trigger digital output for specific seconds when event is triggered The default actions are triggering the D O and storing the media on a CF card D Link DCS 6110 User Manual Product Page DCS 6110 Firmware Version 1 00 DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS HELP Wizard Helpful Hints You can set at most 3 events like motion detection or
35. e several minutes to complete Click Finish to complete installation and the D Link Installation Wizard window will pop up for camera configuration Click Finish D Link DCS 6110 User Manual a7 InstallationWizard 2 1 0 0 1 Setup Choose Install Location Choose the folder in which to install InstallationWizard 2 1 0 0 1 Setup will install InstallationWizard 2 1 0 0 1 in the following folder To install in a different folder click Browse and select another folder Click Install to start the installation Destination Folder ini Installation Wizard 2 Space required 5 7MB Space available 2 656 Nullsoft Install System v2 30 InstallationWizard 2 10 0 2 Setup Completing the InstallationWizard 2 1 0 0 2 Setup Wizard InstallationWizard 2 1 0 0 2 has been installed on your computer Click Finish to close this wizard 14 Section 3 Configuration Configuring Your Camera with the Installation Wizard If the D Link Installation Wizard window does not pop up after completion of software installation click on the icon that was created in your Windows Start Menu The Installation Wizard will appear and show the MAC address and IP address of your DCS 6110 which may appear to be different from the actual address depending on what your device is connected to If you have a DHCP server on your network there will be a valid IP address displayed here Note A DHCP server is a device that supplies the same IP a
36. e source of stream stream1 or stream2 The interval of pre event recording in seconds The maximal recording file duration in seconds Refer page 48 for more information The maximal file size would be generated The prefix name will be added on the file name of the video clip Refer page 48 for more information Select this feature to enable camera to display system log 54 Section 3 Configuration Send post event image s 0 7 Specify to capture the number of images after a trigger is activated A maximum of seven images can be generated For example If both the Send pre event images and Send post event images are set to seven a total of 15 images are generated after a trigger is activated The moment the trigger is activated Add date and time suffix to file name Select this option to add date and time to the file name suffix SNAPSHOTS20080104 100341 T 1 File name prefix Date and time suffix The format is YYYYMMDD HHMMSS D Link DCS 6110 User Manual 55 Section 3 Configuration Maximum duration opecify the maximal recording duration in seconds You can set up to ten seconds For example If the Pre event recording is set to five seconds and the Maximum duration is set to ten seconds the Network Camera continues to record for another four seconds after a trigger is activated he moment the trigger is activated File name prefix Enter the text that will be added at the beginning of the fil
37. efault Gateway Primary DNS Secondary DNS Network Setup Settings for your local area network Select this connection if you have a DHCP server running on your network and would like a dynamic IP address to be updated to your camera automatically You may obtain a static or fixed IP address and other network information from your network administrator for your camera A static IP address will ease you for accessing your camera in the future The fixed IP address The default value is 255 255 255 0 Used to determine if the destination is in the same subnet The gateway used to forward frames to destinations in a different subnet Invalid gateway settings may cause the failure of transmissions to a different subnet Primary domain name server that translates names to IP addresses Secondary domain name server to backup the primary one Enable UPnP Allows a user to find view and control this camera via a presentation page Presentation or Network Neighborhood without configuration How does UPnP work UPnP networking technology provides automatic IP configuration and dynamic discovery of devices added to a network Services and capabilities offered by networked devices such as printing and file sharing are available among each other without bothersome network configuration In the case of Network Cameras you will see Network Camera shortcuts at My Network Places D Link DCS 6110 User Manual Product Pa
38. elete SERVER remove them first from the Motion Detection ve if you want to delete Name Type Address Location y them Time and Date S EE co LETS Serveri email end using different 1 To add a new item event server or media click MS WUAI2S16 eda different even t Add A pop up will appear and update the fields 7777 75 acco rd ly d Media freespace 7200KB Name Type Snapshot snapshot y Snapshot add only sar etn 2 To delete the selected item from the pull down fene the recording entry here menu of event server or media click Delete Moton Detection ON V V V V V DOQD 2400 mation Pease make sue you already set the Server Motion Detection e entry in the Event Setup RECORDING 3 Click on the item name to window for Name Status Sun Mon Tue Wed Thu Fri Sat Time Source Destination Test ON V V V V V 00 00 24 00 streami NAS modifying B media fields D Link DCS 6110 User Manual 51 Section 3 Configuration Application A typical application is that when a motion is detected the DCS 6110 Network Camera sends buffered images to a FTP server or via e mail as notifications For example as seen in the illustration below an event can be triggered by many sources such as motion detection or external digital input devices When an event is triggered you can specif
39. er MANAGE USER User name Viewer can only view the video and audio User password Authentication Administrator Manage user Managing the O Normal User accounts for the existing O Guest users Authentication The access right for the existing users SERVER SETTING Camera Name DCS 6110 SECURITY Section 3 Configuration Backup and Restore You can turn off the front panel LED restore factory default settings and reboot the camera Turn off the LED Check this option to turn off the LED next to the indicator lens This will prevent anyone from observing the operation of the network camera Restore Click the Restore button to reset the camera back to its factory default settings This will remove all the configuration settings that were made previously Reboot Click the Reboot button to restart the camera D Link DCS 6110 User Manual Product Page DCS 6110 Firmware Version 1 00 DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS Device Management Helpful Hints You can turn off the front panel LED restore to factory default and reboot the camera Turn off the front panel LED Check this ff the LED z url o Firmware Update optio Logout SYSTEM next J Turn off the LED indicator bserving the ope RESTORE Restore to Factory Default This option s vill Restore all settin
40. ere the password is not encrypted or Digest where the password is encrypted during the transmission to the web server After you have enabled the Authentication you will need to configure and use the access name to access your video file RTSP camera ip live sdp live sdp is the default access name you can modify it here Access name for The default name is live sdp stream1 Access name for The default name is live2 sdp stream2 D Link DCS 6110 User Manual 40 Section 3 Configuration The accessibility of the RTSP streaming for the three authentication modes are listed in the following table O O O O O Disable O indicates that the authentication mode is supported by the RTSP player X indicates that the authentication mode is NOT supported by the RTSP player Access name for stream 1 Access name for stream 2 The access name is used to differentiate the streaming source When using a RTSP player to access the Network Camera and the video mode is set to MPEG 4 use the following RTSP URL command to request a transmission of streaming data rtsp lt ip address gt lt rtsp port gt lt access name for stream1 or stream2 gt For example when the access name for stream 1 is set to live sdp 1 Launch a RTSP player 2 Choose File gt Open URL This opens the URL dialog box 3 Type the URL command in the text box For example 41 92 158 5 121 dive sdp 4 The live video will be displayed
41. es 29 villjom 30 D ViewCam Installation 67 117110 30 Add a 70 Internet Connection Setup Wizard 30 Motion Detection Setup 35 Fixed Dome Network Camera Features 75 Network Setup 38 Fixed Dome Network Camera Installation 76 Dynamic 44 Image Setup ee 45 Networking Basics 79 Ieri 46 Check your IP address sse 79 Motion 47 Statically Assign an IP address 80 ime and Date 50 D Link DCS 6110 User Manual 2 Table of Contents Reset and Restore een 81 External UO POU 82 Technical Specifications 83 Contacting Technical Support 85 WV AAI EY isd 86 ilg 92 D Link DCS 6110 User Manual Section 1 Product Overview Package Contents e D Link DCS 6110 Fixed Dome Network Camera e CAT5 Ethernet Cable e Screws Power Adapter O Connector Plug e Dome Enclosure Alignment Stencil
42. et the amount of motion in the window being monitored that is required to initiate a motion detected alert If this is set to 100 this means that motion is detected within the whole window to trigger a snapshot Note Setting a higher sensitivity and a lower percentage will make any motion more easily Click to add a new window A maximum of three motion windows can be opened simultaneously Use your mouse to drag the window frame to re size or the title bar to move Clicking on the xX at the upper right corner of the window will close the window Save the related settings of that window D Link DCS 6110 User Manual Product Page DCS 6110 Firmware Version 1 00 In order to use motion detection you must first check the Enable Motion Detection checkbox A maximum of Sets the 3 windows can be created each with their own separate Sensitivity ranges x Video Time and Date Event Setup Access List DI and DO Logout 47 Section 3 Configuration To enable motion detection follow the steps below 1 Click New to add a new motion detection window 2 Enter a name in the Window Name field 3 Define the sensitivity to moving objects and the space ratio of all alerted pixels by moving the Sensitivity and Percentage slide bar 4 Click Save to apply the changes 5 Select Enable motion detection to activate motion detection Note Drag and drop to resize the window and click X to close the windo
43. etwork Camera must be configured to enable multicast streaming at the same time For more information see RTSP Streaming on page 41 3 What algorithm is used to compress the digital image The Fixed Dome Network Camera utilizes MPEG 4 simple profile or MJPEG Mode image compression technology providing high quality images MJPEG is a standard for image compression and it can be applied to various web browsers and application software without installing any extra software D Link DCS 6110 User Manual 75 Section 5 Frequently Asked Questions 4 Can capture still images from the Fixed Dome Network Camera Yes you can capture still images using the snapshot function Fixed Dome Network Camera Installation 1 Can the Network Camera be used outdoors The Fixed Dome Network Camera is not weatherproof It needs to be equipped with a weatherproof case for outdoor use but it is not recommended 2 When physically connecting the Fixed Dome Network Camera to a network what network cabling is required The Fixed Dome Network Camera uses Category 5 UTP cable allowing 10 Base T and 100 Base T networking solutions 3 Can the Fixed Dome Network Camera be setup as a PC cam on a computer No the Fixed Dome Network Camera is used only on an Ethernet or Fast Ethernet network The D Link DSB C1 10 DSB C310 can be used as a PC Camera Webcam 4 Can the Fixed Dome Network Camera be connected to the network if it consists only of private IP a
44. ge DCS 6110 9 DHCP OStatic IP Client IP address Subnet mask Default router Enable UPnP presentation Enable UPnP port forwardin Error Router does not g support UPnP port forwarding Secondary HTTP port Access name for streami Access name for stream2 RTSP STREAMING Authentication Access name for stream Access name for stream2 RTSP port RTP port for video RTCP port for video Enable multicast for stream 1 ulticast group address ulticast video port ulticast RTCP video port ulticast TTL 1 255 Enable multicast for stream 2 ticast group address Iticast RTCP video port Mul Multicast video port Mul Mul ticast TTL 1 255 239 128 1 99 5560 15 239 128 1 100 5564 Save Settings Don t Save Settings Section 3 Configuration Enabling UPnP port forwarding allows the Network Camera to open a secondary HTTP port on the router not the HTTP port meaning that you have to add the secondary HTTP port number behind the Network Camera s public address in order to access the Network Camera from the Internet For example when the HTTP port is set to 80 and the secondary HTTP port is set to 8080 refer to the list below for the Network Camera s IP address http 203 67 124 123 8080 http 192 168 4 160 or h
45. geenent Che Agwenment Jis legal azeernent between you either an individual of an entibr and D Link Cogerstion D Link regarding the use of the D Link softwane entitled Installation Wizard 2 version 1 0 0 2 whieh may include user documentation pucwided in cw electewmie form the Softwar 1 By cliclang the button maered I ACCEPT YES below you sgxee to be bound by the terms of this Agreement Ifyou do not Jagee to the terme of this Agmeerrent please do not install ov use the Software If you accept the terms of the agreement dick I Agree to continue You must accept the agreement to install InstallationWizard 2 1 0 0 2 Click Agree Click the Browse button if you would like to change the destination of EAGEN installation otherwise click Install to continue Choose Install Location N Choose the folder in which to install InstallationWizard 2 1 0 0 2 ry Note Installation may take several minutes to complete Setup will install InstallationWizard 2 1 0 0 2 in the following folder To install in a different folder click Browse and select another folder Click Install to start the installation Destination Folder rogram Files D LinkWnstallation Wizard 2 Space required 5 7MB Space available 3 666 Click Install D Link DCS 6110 User Manual 13 Section 2 Installation To start the installation click Install Note The installation may tak
46. gs to factory default except reset k to settings in Network type Defaut its far tings configuration were made p REBOOT Reboot the system Reboot This option w s optio restart the camera 62 Section 3 Configuration Firmware Update Your current firmware version and date will be displayed on your screen You may go to the D Link Support page to check for the latest firmware version available To upgrade the firmware on your DCS 6110 please download and save the latest firmware version from the D Link Support page to your local hard drive Locate the file on your local hard drive by clicking the Browse button Then open the file and click the Upload button to start the firmware upgrade Current firmware It will be automatically determined and displayed version by the system Current firmware It will be automatically determined and displayed date by the system File Path Locate the file upgraded firmware on your hard drive using the browse feature Upload Start uploading and upgrading the new firmware to your camera D Link DCS 6110 User Manual Product Page DCS 6110 Firmware Version 1 00 DCS 6110 LIVE IDEO SETUP MAINTENANCE STATUS HELP Device Management Backup and Restore Firmware Update Logout Helpful Hints new firmware upgrade may be available for your DCS 6110 It is recommended to keep your DCS 6110 Firm Ipdates are rele eas sed a dc aly to the fun nali
47. in your player D Link DCS 6110 User Manual 41 Section 3 Configuration RTSP port RTP port for video RTCP port for video Multicast group address Multicast video port Untitled 4 Joey The port number that you use for RSTP streaming the default port number is 554 RTP Real Time Protocol Port is used to streaming audio and video while RTCP Real Time Control Protocol port is used to monitor QoS of RTP stream Note RTP video port and RTP audio port must be an even number The numbers of RTCP video port and RTCP audio port must equal to the numbers of RTP video port and RTP audio port plus one repetitively Default port number is 5556 Default port number is 5557 You may choose to enable multicast for your camera audio and video streaming so that your cameras sources and the receivers clients can establish the connection to send and receive contents An IP Multicast group address is used to send and receive content Sources use this group address as the destination address while sending their data packets Receivers use this group address to inform the network that they are interested in receiving packets sent to that group For example if some content is associated with group 239 1 1 1 the source will send data packets destined to 239 1 1 1 Receivers for that content will inform the network that they are interested in receiving data packets sent to the group 239 1 1 1 The receiver joins 239 1 1 1
48. ital input condition trigger condition When external device connect to the digital input pins the state of the voltage will be monitored Max Input 500mA 12Vdc Digital output Select Grounded or Open to define normal status of the digital output The camera will show whether the trigger is activated or not D Link DCS 6110 User Manual Product Page DCS 6110 Firmware Version 1 00 Wizard Network Setup Dynamic DNS Image Setup Video Motion Detection Time and Date Event Setup Access List DI and DO Logout DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS Helpful Hints The I O connector provides the physical interface for digital output DO and digital input DI that is used for mer eios connecting a diversity of external alarm devices to the PTZ IP camera such as IR Sensors and alarm relays general I O terminal block with one digital input and The digital input is used for connecting external alarm devices and once triggered images will be taken and e s mailed Save Settings Don t Save Settings DI AND DO Digital input trigger condition High current status is normal Digital output normal status is Open current status is normal 60 Section 3 Configuration Maintenance Device Management You can modify both camera s name and administrators password of your camera as well as add more user accounts for accessing the camera Admin
49. ke sure that your computer s display properties are set above 256 colors Using 16 or 256 colors on your computer will produce dithering artifacts in the image making the image appear to be of poor quality e The configuration on the Fixed Dome Network Camera image display is incorrect Through the Setup gt Image Setup section of the Web management you need to adjust the image related parameters such as brightness white balance and power line frequency for fluorescent light D Link DCS 6110 User Manual 78 Appendix A Networking Basics Networking Basics Check your IP address After you install your new D Link adapter by default the TCP IP settings should be set to obtain an IP address from a DHCP server i e wireless router automatically To verify your IP address please follow the steps below Click on Start gt Run In the run box type emd and click OK At the prompt type ipconfig and press Enter This will display the IP address subnet mask and the default gateway of your adapter If the address is 0 0 0 0 check your adapter installation security settings and the settings on your access point Some firewall software programs may block a DHCP request on newly installed adapters COWWINDOWS system3 cmd exe Microsoft Windows KP Version 5 1 2688 LG Copyright 1985 2661 Microsoft Corp C Documents and Settings gt ipconfig Mindows Configuration Ethernet adapter Local Area Connection Gonnecti
50. ll be shown in the window of Live Video Click Save Settings to save your changes C 0 Or S e ect e ith er fo r C 0 Or or B M b ac k an d W h ite Product Page DCS 6110 Firmware Version 1 00 Power line You may need to choose 50 or 60 Hz frequency frequency and nonetheless maintain the system operation at Network Setup Note If parameters are changed without saving they will be effective until the next system power up Flip nies will fip the a basic 50 Hz frequency ERU SS image vertical Save Settings Don t Save Settings Image Setup Video LIVE VIDEO Video orientation Two options Flip will vertically rotate the video while Mirror will horizontally rotate the video You may EESS check both options if the camera is being installed upside down a DCS 6110 TCP V 2008 04 07 14 11 34 Logout White balance Choose either Auto or Fix white balance Brightness It has eleven levels ranged from 5 to 5 for you to s Brightness has eleven choose IMAGE SETTINGS evels ranged from 5 to Overlay title and time stamp on video Print Color Color M date time information on of vit Power line frequency 60Hz v left top of video Overlay title and Select to add a date and time stamp directly on Video orientation D Fip time stamp on the video hu video Brightness 0 Overlay title and time stamp on video Save Settings Don t Save
51. lose this wizard Otherwise click Next to begin e Step 1 Specify motion detection Area Settings e Step 2 Motion Detection Schedule e Step 3 Alerts and Notifications Click Next This section will allow you to enable or disable motion detection as well as control the sensitivity or your camera s ability to detect movement Specify the window sensitivity of detection before clicking on the Next button area window name and sensitivity of detection as well L Enable motion detection Snapshot video Clip as the type of recording either snapshot of video clip DCS6110 TCP AV 2008 01 07 01 57 28 Then click Next to continue p cau o Sensitivity 1 Oo Percentage Oy er a sn 4 IL IT Back Click Next D Link DCS 6110 User Manual 35 Section 3 Configuration This section will allows you to specify the time and date your camera records motion Note Recording camera footage will take up space on your hard drive Its recommended that you have sufficient disk space for Always function Click Next This step allows you to specify how you will receive the events notification of your camera either via using email or FTP You will need to enter all the relevant information for your email account or FTP settings Then click Next to continue Click Next D Link DCS 6110 User Manual This section allows you to specify the time and dates that your camera records motio
52. ly number you choose is not in use on the network Set Default Gateway the same Use the folowing IP as the LAN IP address of your access point 192 168 0 1 132 18 0 52 Subnet mask 255 255 255 0 Default gateway 192 168 0 ji Set Primary DNS the same as the LAN IP address of your access point 192 168 0 1 The Secondary DNS is not needed or you may enter a DNS server from your SN Qc mS Preferred DNS 169 91 ISP Alternate DNS 5 Xx ww E Step 5 Click OK twice to save your settings D Link DCS 6110 User Manual 80 Appendix B Reset and Restore Reset and Restore There is a button hidden in the pinhole beside the Ethernet socket It is used to reset the system or restore the factory default settings Sometimes resetting the DCS 6110 will return the system back to a normal state If the system still has problems after reset restore the factory settings and install again RESET 1 Lightly insert a paper clip or a similar sized tool into the reset hole on the back of the camera press lightly and then release the button 2 The LED on the front of the camera will begin blinking red and green Reset button 3 When the LED stops the blinking the reset has completed Restoring the factory defaults will result in RESTORE 1 Insertthe paperclip or other tool and press on the button the loss of any previous settings and will continuously require running
53. m Zoom Zoom Factors 245 Zoom Factors Adjust the threshold of the zoom in and zoom out You can also adjust and position the zoom area by dragging the box 100 400 in the window Click this icon to hide the window D Link DCS 6110 User Manual 26 Section 3 Configuration Digital Zoom Refer to the previous page for more information Start Stop Recording Click to start recording Video clips will be recorded in MP4 format to your computer Press the button again 4 to stop recording If you close your web browser the video will stop recording Resume Pause Click this button 6 to start or pause the transmission of video streaming Click the button again 5 the video will pause Press again to continue streaming Stop Click to stop the transmission of video streaming Click the resume button 6 to begin streaming D Link DCS 6110 User Manual 27 Section 3 Configuration snapshot This section shows a snapshot image from your camera s live video c http 172 17 5 122 cei bin viewer video jpg Microsoft Internet Explorer D Link DCS 6110 User Manual 28 Section 3 Configuration Client Setup You may configure and select the setting for your media streaming and recording Stream Options You can select which video stream profile to use Protocol Options There are 4 protocols for you to choose for the video streaming UDP Protocol This is recommended because
54. mage s 0 7 File name prefix Add date and time suffix to file name Video clip source Pre event recording Maximum duration Maximum file size File name prefix System log D Link DCS 6110 User Manual Th e u n iq u e n am e fo r m ed ia 3 Product Page DCS 6110 Firmware Version 1 00 Select this feature to enable camera to take snapshot ee o Helpful Hints You can set at most 5 different media here for different event Media name The unique The source of stream stream1 or stream2 I video clip and lhe The number of pre event images ped name Sen e event images Aun number of pre event Source Streami Send 1 pre event image s 0 7 Send 1 post event image s 0 7 The number of post event images Refer page 48 for Fle The a ate and time sumx to ne name on th o fien m of the more information ende sii mcm Pre event recording 0 seconds 0 9 add timing Maximum duration 5 seconds 1 10 ns 3 atir n as file name The prefix name will be added on the file name of the Maximum fie sze 00 Kbytes 50 600 n ile Name Prefix snapshot images Check it to add timing information as file name suffix Hefer page 48 for more information Select this feature to enable camera to take video le name prefix The on of the clip video Th
55. n Please note that recorded camera footage will take up space on your hard drive It is therefore recommended that you have sufficient disk space for Always function Sun Man Tue Wed Thu Fri Sat Time Always From to This final step allows you to specify how you receive notification of camera events Choose between an email notification alternatively you can setup an FTP Notification au will need your email account settings or FTP details If you are unsure of this information please contact your ISP Once you have entered this information please click on the Next button Do not notify me O Notify me by E mail User name Password SMTP imaill Server Return E mail Address Recipient email address CO Notify me by FTP User name Password Server address Remote folder name Server port Passive mode 36 Section 3 Configuration You have completed the Motion Detection Wizard Click App ly to Save your setti ngs You have completed your camera setup Please click the Back button if you want to review or modify your settings or click on the Apply button to save and apply your settings Motion Detection Disable Event Take Snapshot Schedule Day Sun Mon Tue wed Thu Fri Sat Schedule Time Always Alerts and Notification Do not notify me ack Click Apply D Link DCS 6110 User Manual 37 Section 3 Configuration LAN Settings DHCP Static IP Client IP Address Subnet Mask D
56. neously from your computer send automated e mail alerts and record video to your hard drive when motion is detected The DCS 6110 is a deluxe size dome network camera giving you a more professional look to your business or location making it an excellent choice for home and business surveillance Note Use of video equipment for recording the image of a person without their knowledge and consent is prohibited in certain states or jurisdictions Nothing herein represents a warranty or representation that the D Link product provided herein is suitable for the end user s intended use under the applicable laws of his or her state D Link disclaims any liability whatsoever for any end user use of the D Link product which fails to comply with applicable state local or federal laws D Link DCS 6110 User Manual 5 Section 1 Product Overview Features e Powerful Surveillance DCS 6110 targets entry level market The VGA Progressive CMOS technology delivers exceptional picture quality Use D Link s SoC system on chip products to provide high quality real time video compression in MPEG 4 and Motion JPEG formats DCS 6110 supports simultaneous dual streaming for live monitoring and recording With the free bundled 32 channel recording software the DCS 6110 is an ideal solution for high quality viewing and reliable recording e Sharp Image Monitoring From Different Angles The DCS 6110 is recommended for indoor ceiling mounting and thus prevents pos
57. ollowing settings System Date Ports e Dynamic DNS If you would like to change the above settings please click on the Back button Click on the Apply button to apply the settings to the device Click Apply A window will pop up to confirm that the application was successfully configured Click OK to continue Click the links below to access the device Access Information Access from Home http 192 168 1 128 A new window will pop up displaying the links addresses to access n eis Sai Sec your device Click Add to my favorite to save the address and then click Exit to complete the installation Click Exit D Link DCS 6110 User Manual Section 3 Configuration Double click DCS 6110 in the Installation Wizard window to launch the camera s web configuration page Note Please see the user manual for more information IP Address Model 00 0D 88 7E 53 DF 192 168 1 187 DCS 6620G 00 02 01 05 03 0 192 168 1 128 DCS 6110 Please check the MAC and model name in the Md product label of your device first S N D5SXXXXXXXXX CEO Then you can start to link to your device and TMM 7 em show the main screen by double clicking the item in the above selection list NTC arouse iD If you are not able to find your device in the above selection list please make sure all cable
58. on specific DHS Suffix dlink IP Address 16 5 7 114 Subnet Mask gt 255 255 255 0 Default Gateway 1H 5 7 1 C 5 Documents and Settings If you are connecting to a wireless network at a hotspot e g hotel coffee shop airport please contact an employee or administrator to verify their wireless network settings D Link DCS 6110 User Manual 79 Appendix A Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway access point or you need to assign a static IP address please follow the steps below Step 1 Windows XP Click on Start gt Control Panel gt Network Connections Windows 2000 From the desktop right click My Network Places gt Properties Step 2 Right click on the Local Area Connection which represents your D Link network adapter and select Properties Step 3 Highlight Internet Protocol TCP IP and click Properties Step 4 Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your access point Internet Protocol TCP IP Properties Example If the network camera s LAN IP address is 192 168 0 1 make your IP assigned automaticaly voa network suppons this capability Otherwise you need to ask your network administrator for address 192 168 0 X where X is a number between 2 and 99 Make sure that the Obtain an IP address automatical
59. ower LED flashes through its cycle twice D Link DCS 6110 User Manual Tilt Screw E Focus Controller Zoom Controller DI DO Pan Screw Section 1 Product Overview Hardware Overview LEDs Power Activity LED D Link DCS 6110 User Manual Section 1 Product Overview Hardware Installation When Mounting to a Ceiling Find a suitable place to install the camera using the alignment stencil Place the camera at the desired operating location and insert the screws through the two holes located at the base of the camera Use a screwdriver to tighten and secure GB 2 o 2 1 QPB Sd When Mounting to a Wall Find a suitable place to install the camera by using the alignment stencil to find a desired operating location on the wall Drill two pilot holes where the holes of the alignment stencil are located Insert the supplied plastic anchors into the drilled holes and align the holes at the base of the camera with the plastic anchors Once aligned insert the provided screws through the holes Use a screwdriver to tighten and secure D Link DCS 6110 User Manual 10 Section 1 Product Overview Network Deployment General Connection without PoE Connect the network camera to a switch via an Ethernet cable Connect the supplied power cable from the camera to a power outlet Connection with a PoE Switch If using a PoE switch connect the network camera to the switch via
60. rd can be changed after installation Click Next D Link DCS 6110 User Manual System setup Camera name pcs 6110 Administrator User name Password Confirm password Date Time setup Date 2008 3 27 Time 10 25 13 hh mm ss Keep current date and time Synchronize with computer time Set date and time manually Synchronize to network time server automatically For security consideration you can assign the hostname and administrator password for your device Anyone who does not have correct password cannot access the device If you forget your administrator password your device must be restored to default settings 16 Section 3 Configuration PPPoE Setup The Network Type screen displays will pop up to ask if you want to setup Newer Type PPPoE for the device Click No for quick setup and skip to page 18 Note By using PPPoE users can virtually dial from one machine to another over an Ethernet network establish a point to point connection between them and then securely transport data packets over the connection DI installation Wizard 2 Setup Your Device D Link The PPPoE Setting screen displays Enter the username and password provided by your ISP to connect to the Internet by PPPoE IP Camera Installatic Step 1 gt gt System Step 2 gt gt PPPoE Setting Click Next and skip to the setup screen as seen in page 19 PPPOE usemame PPPoE
61. re you can configure and schedule the recording settings R eco rd g e nt ry Th eun iq ue name of th e ent ry Product Page DCS 6110 Firmware Version 1 00 name Enable this recording Select this to enable the recording function DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS HELP Helpful Hints Wizard Network Setup You can setup schedule recording to network storage with your specify week day and time period Recording Enable this Priority Set the priority for this entry and the entry With La new E higher priority will be executed first ESE cene See ey seta Enable this recording clip i Source The source of stream s 7 IE E From The time range Recording schedule Scheduling the recording entry PEL ORDING SCHEDULE Sun v Mon v Tue v wed v Thu v Fri v Sat ia Men Time Recording settings Configuring the setting for the recording E Destination Select the folder where will store the recording ARERR SINT Total cycling recording file Destination NAS Total cycling recording size 1000 Kbytes 1000200000000 Size of each file for recording 200 Kbytes 200 6000 File Name Prefix Total cycling Please input a HDD memory volume between 1MB recording size and 200GB for recording space The recording data will replace the oldest one when total to save other esr ihe recording size exceeds this valu
62. s Don t Save Settings VIDEO QUALITY SETTINGS FOR STREAM1 Mode Frame size Maximum frame rate Video quality Constant bit rate Fixed quality MPEG 4 640x480 30fps 512 Kbps Good v VIDEO QUALITY SETTINGS FOR STREAM2 Mode Frame size Maximum frame rate Video quality Constant bit rate O Fixed quality MPEG 4 540x480 Sfps 40 Kbps Good v Save Settings Don t Save Settings Helpful Hints Higher frame size frame rate and bit rate rate gives equires more vit same tiri uires mo NO dth 5 ne itr network bandw Frame Size Three options exist for the sizes of the vide viewing Video Quality This limits the maximal refresh frame rate which can be combined with the Fixed 46 Section 3 Configuration Enable motion detection Window name Sensitivity Percentage New Save Motion Detection Enabling Motion Detection will allow up to three windows that can be created with different settings for monitoring This allows your camera to serve as a security device that will record when motion is detected Check this option to turn on the motion detection Create your own name for the monitored area window It will show at the top of the motion window Set the measurable difference between two sequential images that would indicate motion S
63. s are properly connected to your device and then click on the Refresh Devices button You can find the product label in the rear bottom part of your device Enter admin as the default username and leave the password blank Click OK to continue streaming server User name C m wv Remember my password D Link DCS 6110 User Manual 21 Section 3 Configuration This section shows your cameras live video You can control your settings using the buttons at the bottom For more information on using the web configuration please refer to the user manual Product Page DCS 6110 9 1 m SECURITY D Link DCS 6110 User Manual 22 Section 3 Configuration Adjusting the Lens Based on the live image retrieved from the camera adjust the camera lens by performing the following procedures Adjusting the Viewing Angle Loosen the pan screw and turn the lens module left and right until the desired position is achieved tighten the pan screw once completed Loosen the tilt screws on both sides of the camera and turn the lens module up and down until the desired position is achieved tighten the tilt screws once completed Loosen the image adjustment screw and turn the lens to adjust the network camera s image until the desired orientation is achieved tighten the image adjustment screw once completed Adjusting Zoom and Focus Loosen the zoom controller and adjust the zoom factor by NX moving th
64. sible damage that maybe caused by a burglar This network camera has a built in three axis mechanism for wall mount installation The DCS 6110 provides high quality real time videos in MPEG 4 and MJPEG compression with VGA QVGA QQVGA resolution It is suitable for narrow space surveillance like an elevator e View Live Video from a 3G Mobile Phone The live camera feed of the camera can be pulled from the 3G cellular network by using a compatible cell phone or PDA with a 3G video player Anywhere within the 3GPP service area users are offered a flexible and convenient way to remotely monitor a home or office in real time e Wired PoE Access For effective surveillance in and around a building this camera comes with a built in 802 3af compliant Power Over Ethernet PoE module which eases the installation process and also gives you the freedom to place the camera where it s needed In addition the 10 100BASE TX Ethernet port is also provided for convenient connection to an Ethernet network or to a broadband Internet via a gateway router e Smart amp Easy To Use The software allows you to view up to 32 cameras on a single computer screen at one central location Users can set up automated e mail alerts to be instantly informed of unusual activities Fixed dome cameras usually uses fixed focus lens but the DCS 6110 also has a vari focal lens Vari focal lens provides easier installation process because the board lens of dome camera is not like CS
65. t firmware up to date to maintain and improve the functionality and performance of your internet camera Click here D Link Support Page to check for the latest firmware version available To upgrade the firmware on your DCS 6110 please download and save the latest firmware version from the D Link Support Page to your local hard drive Locate the file on vour local hard drive by clicking the Browse button Once you have found and opened the file using the browse button click the Upload button to z bel 1 de start the firmware upgrade jur suppor site on the FIRMWARE INFORMATION our support site link an in sms te m m ware Current Firmware Version 1 00 tailable for Current Firmware Date 27 Mar 2008 cam era FIRMWARE UPGRADE File Path Coss 63 Section 3 Configuration Status Device Info This page displays all the details information about your device and network connection Product Page DCS 6110 Firmware Version 1 00 DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS HELP Logs All of your network connection details are displayed on this page The firmware version is also displayed here da LAN Logout BASIC INFORMATION Camera Name DCS 6110 Date and Time D8 Apr 2008 17 40 09 Firmware Version 1 00 27 Mar 2008 IP address 172 17 5 79 Subnet mask 255 259 259 0 Default router 172 17 5 254 Primary DNS 192 168 168 210 Secondary DNS 192 168 168 250 PP
66. tection The setting of the firewall may need to be changed in order for the Fixed Dome Network Camera to be accessible outside of your local LAN Check with the Network Administrator for your network Make sure that your Fixed Dome Network Camera isn t conflicting with any Web server you may have running on your network e The default router setting might be a possible reason Check that the configuration of the router settings allows the Fixed Dome Network Camera to be accessed outside of your local LAN 8 connected the Fixed Dome Network Camera directly to a computer with a cross over Ethernet cable and received a Windows error upon running the installation Wizard e This Windows error will occur if the Fixed Dome Network Camera is connected to a computer that is not properly configured with a valid IP address Turn off DHCP from the Network Settings in Windows and configure the computer with a valid IP address or connect the camera to a router with DHCP enabled e This error can also occur if the Installation Wizard icon is clicked on more than once from the setup wizard 9 Grainy images occur How can solve the problem The video images might be grainy if the Fixed Dome Network Camera is used in a very low light environment To solve this issue you need more lighting D Link DCS 6110 User Manual 77 Section 5 Frequently Asked Questions 10 The images appear to be of poor quality how can improve the image quality e Ma
67. the motion detection window In this case 50 of pixels are identified as alerted pixels When the percentage is set to 30 the motions are judged to exceed the defined threshold therefore the motion window will be outlined in red For applications that require higher security management it is suggested to set higher sensitivity settings and smaller percentage values D Link DCS 6110 User Manual 49 Section 3 Configuration Time and Date From this section you may automatically or manually configure update and maintain the internal system clock for your camera Curre nt Server Time Will be determined by the system Product Page DCS 6110 Firmware Version 1 00 Time Zone Select your time zone from the drop down menu DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS HELP Wizard Helpful Hints ber died The Time Configuration option allows you to configure update and maintain the correct time on the internal Essa m ds system clack From this section you can set the time zone that you are in and set the NTP Network Time Important for accurate logs Dynamic DNS and sche irewall rules KONTEN Protocol Server Daylight Saving can also be configured to automatically adjust the time when needed and scheduled firewall rules Enable Daylight Select this to enable the daylight saving time Saving DST During DST the system clock moves hour ahead Note To utilize this feature ensure to set the time zone of your ne
68. tion Utility To access the configuration utility open a web browser such as Internet Explorer and enter the IP address of your Network Camera http 192 168 0 120 Note In the example this address is 192 168 0 120 Your adaress may differ Type Admin in the user name field and leave the password blank by default Note You may refer to page 60 to change the password for your admin account Click OK D Link DCS 6110 User Manual D Link Microsoft Internet Explorer File Edit view X Favorites Tools Help M gt Le pa Search Address 192 168 0120 Eg Connect to 192 168 1 130 streaming server User name admin Password Remember my password 25 Section 3 Configuration Live Video Camera This section shows your camera s live video You can control your settings using the buttons below Client Settings Click this button to access the client setting page For more information see Client Setup on page 30 Zoom Click to enlarge objects Click to reduce the size of the object Focus Click for a close up of an object Click to shoot faraway objects Zoom speed Adjust zoom and focus speed Focus speed Enable Disable the digital zoom feature After selecting this e icon a small pop up window will appear see below eJ 5j nj SECURITY Disable Digital Select this to disable the digital zoom feature Disable digital zoo
69. to choose a specific folder for the installation D Link D ViewCam otherwise click Next to continue Choose Destination Location Select folder where setup will install files Setup wall install D Link DM am in the following folder Ta install to this folder click Next Ta install to a different folder click Browse and select another folder Destination Folder CAP rogram nk Dien um Installshield Cancel Click Next D Link DCS 6110 User Manual 68 Section 4 D ViewCam Installation Click Next to start the installation Note The D ViewCam installation process may take several minutes to complete Click Next Click Finish to complete the installation Click Finish D Link DCS 6110 User Manual D Link D ViewCam Start Copying Files Review settings before copying Files Setup has enough information to start copying the program files IF you want to review or change any settings click Back If pou are satisfied with the settings click Next to begin coping files Installshield D Link D ViewCam InstallShield Wizard Complete Setup has finished installing D Link O ViewCam on your computer Finish Cancel 69 Section 4 D ViewCam Installation Add a Camera This section will show you how to start and add a camera to the D ViewCam system To start D ViewCam select Start gt All Programs gt D Link gt E3 Dunk fa D ViewCam KG D Link D ViewCam D
70. ttp 192 168 4 160 8080 Enable UPnP Port Enables the camera to add the port forwarding entry into the router automatically when this option is enabled Forwarding PPPoE Settings Enable this setting if your ISP DSL service is using PPPoE You may already have both Username and Password given by your ISP or you may check with your ISP The Connect Status will be determined automatically by the system HITP You may configure two HTTP ports for your camera HTTP ports allow you to connect to the camera via a standard web browser These ports can be set to a number other than the default TCP ports 80 and 8080 A corresponding port must be opened on the router For example if the port is changed to 1010 users must type in the web browser http 192 168 0 100 1010 instead of http 192 168 0 100 Authentication Authentication Choose either Basic where the password is not encrypted or Digest where the password is encrypted during the transmission to the web server If you select Digest you must close and then re open your web browser Basic authentication When selected the password is sent in plain text format there can be potential risks of being intercepted Digest authentication When selected user credentials are encrypted in MD5 algorithm and thus provide better protection against unauthorized accesses HTTP Port The default value is 80 D Link DCS 6110 User Manual 39 Section 3 Configuration Secondary HTTP The def
71. twork camera Then starting ending time of the DST is displayed upon selecting option Daylight Saving You may configure the daylight saving date Dates time Automatic Time Enable this feature to obtain time configuration Configuration automatically from NTP server NTP Server Network Time Protocol NTP synchronizes the DCS 6110 with an Internet time server Choose the one that is closest to your location Image Setup Video Motion Detection Event Setup Access List DI and DO Logout TIME CONFIGURATION Current Server Time Save Settings Don t Save Settings 07 Apr 2008 17 13 18 Time Zone GMT 08 00 Las Vegas San Francisco Vancouver Enable Daylight Saving Daylight Saving Dates Month Week Day of Week Time DST Start Jan ist Fri 12am DST End Jan ist Fi 12am AUTOMATIC TIME CONFIGURATION O Enable Disable NTP server Update interval SET THE DATE AND TIME MANUALLY Year 2008 Hour 17 Update Interval The time interval for updating the time information from NTP server Set the date and time This option allows you to set the time and date manually manually Copy Your Computer s This will synchronize the time information from your PC Time Settings D Link DCS 6110 User Manual Month 04 Day Minute 13 Second Copy Yo
72. ual Below you should see a summary of your camera settings Click back to review or modify settings Click Restart to apply the settings below Please note these settings as you will require this information when accessing your camera on the network or via your web browser IP address DHCP Camera Mame DCS586110 Time zone 8 DDNS OFF PPPOE OFF ack Below you should see a summary of your camera settings Click back to review or modify settings Click Restart to apply the settings below Please note these settings as you will require this information when accessing your camera on the network or via your web browser IP address PPPoE Camera Mame D56110 Time Zone 8 DONS PPPOE ON Below you should see a summary of your camera settings Click back to review or modify settings Click Restart to apply the settings below Please note these settings as you will require this information when accessing your camera on the network or via your web browser IP address 192 168 0 100 Camera Mame DCS6110 Time Zane 8 DONS PPPOE OFF 34 Section 3 Configuration Motion Detection Setup Wizard This wizard will guide you through a step by step process to configure your new D Link Camera motion detection functions Click Next to continue This wizard will guide you through a step by step process to configure your camera s mation detection functions To setup the internet connection settings please click Cancel to c
73. uently Asked Questions Frequently Asked Questions This chapter provides solutions to problems that may occur during the installation and operation of the DCS 6110 Read the following descriptions if you are having any problems Note The examples below are illustrated in Windows XP If you have a different operating system the screenshots on your computer will look similar to the following examples Fixed Dome Network Camera Features 1 What is a Fixed Dome Network Camera The Fixed Dome Network Camera is a stand alone system connecting directly to an Ethernet or Fast Ethernet network The Fixed Dome Network Camera differs from a conventional PC Camera because it has an integrated system with built in CPU and web based solutions providing a low cost solution that can transmit high quality video images for monitoring The Fixed Dome Network Camera can be remotely managed accessed and controlled from any PC Notebook over an Intranet or Internet using a web browser 2 What is the maximum number of users that can access DCS 6110 simultaneously The maximum number of users that can log onto the Fixed Dome Network Camera at the same time is 10 Please keep in mind the overall performance of the transmission speed will be reduced if many users have logged on to the camera simultaneously There is no limited user when multicast enabled router is used This helps to reduce the network transmission load Note that to utilize this feature the N
74. up Status Logout LIVE VIDEO Camera Snapshot Client Settings Logout Wizard Network Setup Dynamic DNS Image Setup Audio and video Motion Detection Time and Date Event Setup Access List DI and DO MAINTENANCE e Admin e System e Firmware Update STATUS e Device Info e Logs SECURITY 66 Section 4 D ViewCam Installation D ViewCam Installation D ViewCam software is included for the administrator to manage up to 32 D Link network cameras remotely The administrator can use the software to configure the advances settings for the camera D ViewCam is a complete management tool and includes all configurative settings Insert the CD ROM into the CD ROM drive A menu screen will appear as shown below D FIXED DOME NETWORK CAMERA Installation Wizard Click D ViewCam D ViewCam View Documentation Network Magic amp Support Registration DCS 6110 Business Class Networking D ViewCam provides English Traditional Chinese and Simplified CIRSSSSSERAXENENSSS Chinese language versions Select a language version and click OK to continue Click OK D Link DCS 6110 User Manual 67 Section 4 D ViewCam Installation Click Next to continue D Link D ViewCam Welcome to the InstallShield Wizard for D Link D ViewL am The InstallShield Wizard will install D Link D ViewCam on our computer To continue click Next Click Next Click Browse if you would like
75. ur Computer s Time Settings Save Settings Don t Save Settings Time Zone Select your time zone from the drop down menu Enable Daylight Saving Select this to enable the daylight saving time Daylight Saving Dates You may configure the daylight saving date and time Automatic Time Configuration Enable this feature to obtain time configuration automatically from NTP server NTP Server Network Time Protocol NTP synchronizes the IP camera time Update Interval The time interval for updating the time information from NTP server Copy Your Computer s Time Settings Set the date and time manually This option allows you to set the time and date manually This will synchronize the time information from your PC 50 Section 3 Configuration Event Setup T h e re a re th re e S ect S Fve nt S et u p D aQ e Product DCS 6110 Firmware Version 1 00 They are e Event o S e rve r There are four sections in Event Setup page They are event server media and recording Click Add to pop Dynamic DNS a window to add a new item of event server media or recording Click Delete to delete the selected item U1 00H i jars form event server media or recording Click on the item name to pop a window to edit it There can be at e d a Image Setup most three events and two recording There can be at most five server and five media configurations Video dify or d
76. w The Percentage Indicator will rise or fall depending on the image variation When motions are detected by the Network Camera and are judged to exceed the defined threshold a red bar rises Meanwhile the motion detection window will be outlined in red Photos or videos can be captured instantly and configured to send to the remote server Email FTP by utilizing this feature as a trigger source A green bar indicates that even though motions are detected the event will not be triggered because the image variations are still falling under the defined threshold Percentage 30 D Link DCS 6110 User Manual 48 Section 3 Configuration How does motion detection work Enable motion detection There are two parameters for setting the motion detection Sensitivity and Percentage In the illustration above frame A and frame B are two sequential images Pixel differences between the two frames are detected and highlighted in gray frame C and will be compared with the sensitivity setting Sensitivity is a value that expresses the sensitivity to moving objects Higher sensitivity settings are expected to sense a slight movement while smaller sensitivity settings tend to neglect it When the sensitivity is set to 7096 the Network Camera defines the pixels in the purple areas as alerted pixels frame D Percentage is a value that expresses the proportion of alerted pixels to all pixels in
77. y what kind of action will be performed You can configure the Network Camera to send snapshots or videos to your email address or FTP site Event Condition Action ex Motion detection Periodically Digital input System reboot Media Server what to send where to send ex ex Snapshot Video Clips Email FTP To start plotting an event it is suggested to configure server and media columns first so that the Network Camera will know what action shall be performed when a trigger is activated D Link DCS 6110 User Manual 52 Section 3 Configuration Add Server Up to 5 servers where will store the media with its own settings can be created and configured here Server Name Unique name of your server Email Select this to enable and apply your email account setting for your camera FTP Select this to access a granted folder on the external FTP server HTTP Select this to use a web server to store the media Network Storage Only one network storage is supported D Link DCS 6110 User Manual Product Page DCS 6110 Firmware Version 1 00 DCS 6110 LIVE VIDEO SETUP MAINTENANCE STATUS HELP Wizard Dynamic DNS Image Setup Video Motion Detection Time and Date Access List DI and DO Logout You can set at most 5 different servers here for different event Save Settings Don t Save Settings SERVER TYPE Server name Email Sender email address Recipient

Hardware Installation - D-Link

Contents

Download Pdf Manuals

Related Search

Related Contents