User Manual
Contents
1. i LLI EP Series Pizza Oven II III IV VI VII VIII IX 2 6 Index Machine illustration diagram Part list Warning Installation instruction Operation instruction Maintenance Trouble shooting Specification Electrical drawing Please read instruction before using the oven I EP2 amp EP1 Explode diagram EP2 II Part list i E E E E E E E 3 6 EPA III Warning 1 The oven must not be installed in proximity of inflammable materials wood plastics combustible gas etc 2 Avoid the contact of inflammable objects with the hot surfaces of the oven Always assure the safety fireproof conditions Maintain a free space around the oven of at least 50cm 3 For safety reasons the maximum temperature allowed is 350 deg C despite thermo control can be over such temperature as special required to install for tailor made feature 4 Itis forbidden to use throws or drips of water abrasive of corrosive substances and anything else that can damage the components compromise the safety and be dangerous from an hygienic point of view 5 Do not use the wet hand to touch the any switch or part on the switch panel 6 Do not use the oven if any damage part found 7 Keep away from chirlden 8 Read all instruction before use 9 Oven should be installed by qualified electrician by local law 10 Maximum continuous work time is 12 hours The oven must be stop for cooling for 3 hours before w2. SAI Power Switch SAR Switch For Light HL1 Light SA1 Power Switch SA Switch For Light HL 1 Light EH Heating Element Q1 Q3 Thermostat HL2 HL4 Indicator Light For EH Heating Element 1 Q2 Thermostat HL2 HL 2 Indicator Light Heating Element 6 6
3. n it The bonding wire must have a minimal section of 10mm V Operation 1 Before the ignition of the oven remove the protective film and all polyfoam inside the chamber Indicator Light For Heating Element Thermostat 8 Indicator Light For Heating Element Thermostat mir ee Indicator Light For Heating Element Thermostat mm PA Switch For Light p Power Switch 2 Turn on the main switch to position 1 3 Turn upper and lower thermo control desired temperature Power indicator light up for heating element working The light turn off if the desired temperature reached The heating element is automatic switch on if the chamber temperature is lower than the desired setting temperature At the same time the indication light turn on if the heating element working again 4 Check the chamber temperature bv thermometer for EP4 6 8 12 series For EP2 it is timer for cooking alert purposes 5 Check the Pizza or food by turn on the chamber light 6 For EP4 EP6 EP8 and EP12 in the left hand side of the door pushing staff ball for closing exhaust window to keep or pulling staff ball to open exhaust window for different cooking purposes l For switch off the oven turning the main switch to position 0 VI Maintenance Before executing any kind of maintenance including cleaning you must disconnect the oven electricallv and wait for the complete cooling In the case of malfunctioning or damage of the oven vo
4. ork again 11 No direct water spray cleaning 12 No direct touch by hand on any part of the oven expect operation on switch panel door handle and staff ball for exhaust air 13 Operator should be keep taking care of oven when the oven turn on 14 Check the electric wire breakage due to material fatigue periodically eg Inspection per every 3 months IV Installation 1 Installation and maintenance have to be done by qualified personnel authorized by the manufacturer or dealer who is not responsible for any mistaken installation or manumission 2 The place where the oven is installed must have the following environment al characteristics be dry water sources at safe distance adequate ventilation and lighting corresponding to hygiene and security rules following the existing law 3 Verify that the electrical set up corresponds with the numbers of the technical characteristic and on the small plate at the back of the oven The characteristics of the electric socket must be compatible with the plug installed on the cable 4 The connection with the electric network must be made by putting a suitable differential automatic cut out in which 4 6 the distance of the aperture between the contracts is at least of 3 mm It is necessary to connect the equipment on the ground 5 The equipment must be connected with an equi potential system The connection is made with the terminal close to the cable the one which has this symbol o
5. u must applv for authorized assistance form the manufacturer or authorized dealer Cleaning The cleaning must be done everv time the oven has been used following all the rules to provent malfunctioning of the oven and for hvgienic purposes Using a suitable spatula and solft metal brush remove the cooking 5 6 residues from the fire stone which they go subsequently removed with a aspirator VII Trouble shooting Possible solution b Check electrical wiring collectly connected 2 Setting the upper and bottom thermo control to desired temperature No heating up 8 Wrong input voltage or phase Call authorized dealer if other case Electric shock Stop using the oven and call authorized dealer for service Chamber no light Turn on the chamber of call authorized dealer to replace bulb Bad burning smell Call authorized dealer to check electrical circuit Un even cooking Re set upper and bottom thermo control Or call authorized dealer to check whether the heating element burn and replace VIII Specification vico Temperature Outside dimension Chamber dimension Rated voltage Rated Power ode range mm mm V kW EPIS 0 350 560X570X280 410X410X110X1PCS 220 240V EPIP 0 350 560X570X280 410X410X110X1PCS 220 240V IX Wiring diagram legend Eiectric diagram for 220V 240V EP2P amp EP2S Eiectric diagram for 220V 240V EP1P amp EP1S 220 240V 50Hz 220 240V 50Hz EE L N PE IL N HLI HL1
Download Pdf Manuals
Related Search