Home

VoIP Fiber Optical Router User`s Manual

1. Enable IP Filtering Check the box to deny particular LAN IP addresses from accessing the Internet IP Enter the IP address that you want to deny in this filed TCP UDP Select TCP UDP or Both that will be used with the IP address that will be blocked Remark Enter comments VolP Wireless Router User s Manual 70 2 5 14 Port Filtering Port filtering enables you to control all data that can be transmitted over routers When the port used at the source end is within the defined scope it will be filtered without transmission Note When the port used at the source end is within the limited scope it will be filtered without transmission Advanced Settings Port Filtering TCP UDP Both Both Both Both s Enable Port Filtering This variable is to restrict certain types of data packets by port Port Range Enter the port range that will be denied access to the Internet TCP UDP Select TCP UDP or Both that will be used with the port that will be blocked Remark Enter comments 2 5 15 MAC Filtering MAC Media Access Control address filtering allows you to filter the transmission of data by network card physical address Advanced Settings MAC Filtering Enable MAC Filtering MAC Goon xx ee Enable MAC Filtering Enter a MAC address to prevent the particular device from accessing the Internet MAC E
2. Confirm Password eecccecece MTU is WAN 1 Domain Name Server Manual Domain Name Server Primary IP 168 9511 Domain Name Server Secondary IP Po Enable Dual Access Second Access IP Type Hostname Vendor Class ID PPTP Point to Point Tunneling Protocol PPTP is a WAN connection Enter the IP Address Subnet mask PPTP Server PPTP ID and Password VolP Wireless Router User s Manual 17 General Settings WAN WAN Link Speed WAN Link Speed WAN Link Speed Select WAN port link speed General Settings WAN Connection VoIP Connection Interface Select a WAN interface for VoIP traffic bound with as WAN 2 is enabled General Settings WAN Factory Default MAC Address 00 01 75 10 02 09 Restore Your MAC Address 00 90 00 E7 2E 40 Clone Current MAC Address oca Factory Default MAC Address The original MAC address of the VolP Router Your MAC Address It is left blank as you log in via the WAN port Current MAC Address lt shows the current MAC Address if you ever used the different MAC address from Factory Default MAC Address You can click Clone to automatically copy the MAC address of the Ethernet Card installed in the computer used to configure the device Note This is only necessary to fill the field if required by your ISP VolP Wireless Router User s Manual 18 2 3 2 LAN General Settings LAN LAN IP LAN default Gateway
3. IP address Settings e After entering IVR mode dial 111 When voice prompt plays Enter value enter your IP address followed by Example If the IP address is 192 168 1 200 dial 192 168 1 200 Subnet Mask Settings e After entering IVR mode dial 112 When voice prompt plays Enter value enter your subnet mask followed by ff Example If the subnet mask value is 255 255 255 0 dial 255 255 255 0 Default Gateway Settings After entering IVR mode dial 113 When voice prompt plays Enter value enter your default gateway s IP address followed by Example If the default gateway is 192 168 1 254 dial 192 168 1 254F Save Settings and Restart To save settings dial 509 Save Settings The system will save the current settings Please restart the system Wait for about 40 seconds for the system to restart and then enter 101 to check whether the IP address was retained If the system does not play back the IP address after dialing 101 this indicates that the VolP Router currently is not connected to the Internet Please check and make sure the cable connections account numbers and passwords are correct Dynamic IP DHCP Settings After entering IVR mode dial 114 When voice prompt plays Enter value dial 2 to select DHCP Saving settings press 509 Save Settings Please restart the system After the system is restarted press 101 to check whether or not the IP address was r
4. oIP failure announcement VolP failure announcement Check the box to play a voice announcement if the VolP Router fails to register to the SIP proxy server while FXS is off hook VolP Wireless Router User s Manual 27 e5 C Vor Call Out Notification Enable Built in Call Hold Music Call On Hold Notification Enable Non SIP Inbox Call Invite URL need user phone O Reliability of Provisional Responses O Compact Form SIP Caller ID Obtaining Remote Party ld Depay Name O Put Caller ID In URI C INVITE With Remote Party ID Header Callee Quick Media Disable e FXS Hunting For Unknown Number Disable hal O Support URI Percent Encoding RFC 3986 Call Hold Compatible With RFC 2543 Enable SIP Allow Header L Enable SDP ptime Attribute O Use Redirect URI As To Header Receiving 3XX C Respond BUSY HERE while no line available for hunting VoIP Call Out Notification Check the box to enable the function of playing a tone to notify user that the call is through VoIP Enable Built in Call Hold Music Check the box to enable the function of playing music when receiving Call Hold request Call On Hold Notification FXS will send alert to phone set as users hang up if there is a call still held in another line Enable Non SIP Inbox Call Check the box to make local calls Local Call here means the call does not go through the Internet and if the dialed number is the extension of other line You can
5. 192 168 8 254 Subnet mask 255 255 255 0 LAN IP LAN default Gateway Enter the LAN IP address of the VolP Router It is also the default gateway for DHCP clients Subnet Make Enter the subnet mask for DHCP clients General Settings LAN DHCP Server Enable DHCP Server IP Pool Starting Address 192 168 8 1 IP Pool Ending Address 192 168 8 250 C IP Pool Uses Other Default Gw h gt Tinto fo een Le Toe hid Le Wiad Y Lease Time 1 J 1 9999hours Domain Name Server Assignment 2 Auto Manual Th proce Ble ee Coes eee CU i F I F mall a Th g a x J nadal Enable DHCP Server This variable is to assign the IP address for the devices connected to LAN port of the VolP Router IP Pool Starting Address Enter the starting IP address for the DHCP server s IP assignment IP Pool Ending Address Enter the ending IP address for the DHCP server s IP assignment IP Pool Uses Other Default Gw Check the box to assign different default gateway for DHCP clients IP Pool Default Gateway Enter the new default gateway that is different from LAN IP of the VolP Router IP Pool Subnet mask Enter the new subnet mask Lease Time Enter the length of time for the IP lease Domain Name Server Assignment Select Auto or Manual to get the IP address of Domain Name Server assigned by ISP or manually Domain Name Server IP Enter the primary and second
6. Soft Switch Check the box to register the VoIP Router with SIP proxy server or soft switch ITSP Name Enter the name of VSP General Settings SIP FXS Representative Number registers to Proxy line Type Number Hunt Group Register Mvite with ID UserID Password and Confirm Account Account Password ais enssssese FXS Representative 08 12345678 0912345678 Mumber CZ ETERA No Group ry eneeeeeen A ee ee ee ee dl E AA es EPIA No Group ry eneseneen fee ees ee eS H l Number Enter the representative number for FXS ports If the VoIP Router is configured to register with SIP proxy server all the lines are using this number to call through SIP proxy server It is the Caller ID for the called party when you make a VoIP call If you register the VolP Router to a SIP proxy server then it should be the number that provided by SIP proxy server Register Check the box to register with SIP proxy server User ID Account User ID Account are usually the same as Number from most SIP proxy severs Password Enter password and re enter to confirm Note Please ensure if your VoIP Service Provider allows one account for multi port using VolP Wireless Router User s Manual 21 General Settings SIP Each line registers to Proxy independently Hunt Group Invite with ID Password and Confirm Line Type Account Pp Regis
7. There are 10 VoIP route profiles Each VoIP route profile provides four routes to select Server 1 Server 2 Server 3 Phone Book and None can be selected for each route 1 2 3 4 PhoneBook v Server 1 we Server 2 j Server 3 None None None wt None None Mone gt None None Mone None None w None None iM None None w None None w None w None None None None we None None None wr None wr None Mone None hal None J None is None None a VolP Wireless Router User s Manual 57 Methods of Digit Map Method 1 Single mapping Fill a short code into the Scan Code column and enter the desired phone number into the VoIP Dial out column For example Scan Code 09 VoIP Dial out 0911888997 User Dial Length 2 Route VolP VoIP Route Profile Route 1 Digitmap VoIP Dial out User Dial Length Route Pick up the handset and dial 09 the VoIP Router will dial 0911888997 and follow Route 1 Method 2 Multi mapping Fill the prefix code into the Scan Code column and the format to transfer into the VoIP Dial out column For example Scan Code 2 VoIP Dial out 35106 User Dial Length 4 Route VoIP VoIP Route Profile Route 2 Digitmap Enable Scan VoIP Dial out User Dial Length Route 0911888997 a E Pick up the handset an
8. Uniform Resource Locator of the remote peer Port Enter the listen port of the remote peer VolP Wireless Router User s Manual 39 2 3 11 CDR Settings The user can set up a CDR Server to record call details for every phone call General Settings CDR C Send record to CDR Server Send record to CDR Server Tick the check box to enable the call detail recording CDR Server IP Domain Enter the IP address of the CDR server Port Enter the listen port of the CDR server RADIUS Tick the checkbox to enable RADIUS as database and enter the information of RADIUS needed It includes RADIUS Accounting Port RADIUS Server Secret RADIUS User ID and RADIUS Password VolP Wireless Router User s Manual 40 2 4 Wireless Settings 2 4 1 Basic Settings Wireless Settings Basic Settings Enable Wireless LAN Interface Wireless Network Name SSID sso Wireless Channel Auto Scan recommended 802 11 Mode Mixed 802 11n 802 119 and 802 11b Mode Client e Network Type Infrastructure Broadcast SSID Enable Universal Repeater Mode Acting as AP and client simultaneouly SSID of Extended Interface r Show Status Enable Wireless LAN Interface Enable wireless basic settings on LAN interface Wireless Network Name SSID SSID is the name of your wireless network All wireless equipped devices share the same SSID to communicate with each other It must be unique to identify
9. WPA2 Cipher Suite RADIUS server IP Address RADIUS server Port RADIUS server key Select the type of WPA WPA WPA2 WPA2 Mixed choose the proper security mode according to your wireless network WPA Authentication Mode Select Enterprise RADIUS WPA Cipher Suite WPA Cipher Suite is used for the configuration of WPA or WPA2 Mixed TKIP TKIP is the security protocol used in WPA The length of TKIP encryption is longer than WEP encryption that increases the complexity of decoding for crackers AES The most powerful encryption algorithm that is commonly used in WPA WPA2 Cipher Suite WPA2 Cipher Suite is used for the configuration of WPA2 or WPA2 Mixed TKIP TKIP is the security protocol used in WPA The length of TKIP encryption is longer than WEP encryption that increases the complexity of decoding for crackers AES The most powerful encryption algorithm that is commonly used in WPA RADIUS Server RADIUS server Port Enter the port number of the authentication RADIUS server Keep the default value 1812 unless the server required change to another number RADIUS server IP Address Enter the IP address of the authentication RADIUS server RADIUS server key Enter the password such as a security Key VolP Wireless Router User s Manual 45 2 4 4 Access Control Wireless Settings Access Control Access Control Mode Disable Disable The
10. 25 2 3 4 SIP Advanced General Settings SIP Advanced Listen Port UDP 5060 1 65535 RTP Starting Port UDP 9000 1 65500 SIP Transport Protocol UDP Listen Port UDP Enter the VoIP Router s listening port in this field Leave it as default settings unless it conflicts with ports used by other device in your network RTP Starting Port UDP Enter the starting port number or transmitting voice data among VoIP devices Each line requires 2 ports SIP Transport Protocol UDP or TCP General Settings SIP Advanced International Call Prefix Digit Country Code Other Long Distance Call Prefix Digit rea Code C E 164 Numbering To Invite Proxy International Call Prefix Digit Enter the International call prefix Country Code Select the desired country code from the drop down menu or enter the country code if Other is selected Long Distance Call Prefix Digit Enter the long distance prefix digit for making a long distance call Area Code Enter the area code E 164 Numbering To Invite Proxy This variable is followed the E 164 rule but it depends on the SIP proxy server Click the check box to send the number following the E 164 rule by the VolP Router ENUM Header Exception Enter the prefix number that the VolP Router sends the number without followed the E 164 rule Note E 164 Numbering depends on the proxy If you fail to make a call please contact your VoIP Service Provi
11. Destination 192 160 0 254 Number of Ping 4 1 100 Ping Packet Size 56 56 5600 bytes Result PING 192 168 858 254 192 168 8 254 56 data bytes 64 bytes From 192 168 8 254 seg 0 ttl 64 tine 0 4 ms 64 bytes From 192 168 858 254 seg 1 ttl 64 time 0 4 ms time 0 3 ms 64 bytes From 192 168 8 254 seg 2 ttl 64 time 0 3 ms time 0 3 ms 64 bytes From 192 168 585 254 seg 3 ttl 64 time 0 3 ms time 0 3 ms 192 165 5 254 ping statistics 4 packets transmitted 4 packets received 0 packet loss round trip minfawg max 0 3 0 3 0 4 ms VolP Wireless Router User s Manual 73 2 6 2 STUN Inquiry Use STUN Inquiry to detect your IP sharing device s NAT type and communication between a STUN server and client Tools STUN Inquiry WAT Type Unknown STUN Server IP Domain STUN Server Port 3478 1 65535 NAT Type lt shows the NAT type of your router STUN Server IP Domain Enter the IP address or URL of the STUN server for query STUN Server Port Enter the STUN Server s listening port VolP Wireless Router User s Manual 74 2 7 System Settings 2 7 1 NTP System settings NTP Time Server NTP time server 1 _ntp ucsd edu NTP time server 2 ntp univ Jyon fr i NTP time server 3 tme nuri net Time Configuration Current Router Time 2000 11 1 15 03 41 Time Zone e x oo Automatically synchronize with Internet time servers The VolP R
12. Do Not Line Type Disturb Unconditional Forward Busy Forward Representative LI number z 1 2 FXS As BEA le Y Line Type Call Hold Call Transfer Call Waiting Three Way Calling Service ID 1 2 FXS d FxS d Do Not Disturb Check the box to reject busy tone played incoming calls Unconditional Forward Check the box to forward incoming calls to the assigned Forwarding Number automatically Busy Forward Check the box to forward incoming calls to the Forward incoming Number when the line is busy No Answer Forward Check the box to forward incoming calls to the Forward incoming Number after ringing timeout configurable from 10 to 60 seconds expires Call Hold Check the box to hold the call on the specific FXS port Note Call Transfer or Call Waiting can only be activated when Call Hold is checked Call Transfer Check the box to transfer the call to another destination Call Waiting Check the box to accept incoming call while talking Three Way Calling Service ID It is for conference all based on Nortel Soft Switch and must work with Proxy Server that supports Three Way Calling service Local Mixer It is used to enable build in conference service when ticked VolP Wireless Router User s Manual 37 Enable Call Feature Code Call Feature Code Enable Call Feature Code Unconditional Forward FxS Representative Number Wa
13. IVR Interactive Voice RESPONSE cccccccseececcseseecceesececseseccsuseeessauececseaseeeeaaseesseaseeessageeeessneeesssageeseas 79 3 2 IP Configuration SellingS tooodo 81 A DIAUNG PrnNCIDIES auspiciada 83 VolP Wireless Router User s Manual 1 1 Introduction 1 1 Product Overview The VoIP Router is designed to carry both voice and facsimile over the IP network It uses the industry standard SIP call control protocol so as to be compatible with free registration services or VoIP service providers systems As a standard user agent it is compatible with all common Soft Switches and SIP proxy servers While running optional server software the VoIP Router can be configured to establish a private VolP network over the Internet without a third party SIP Proxy Server The VoIP Router can be seamlessly integrated into an existing network by connecting to a phone set and fax machine With only a broadband connection such as an ADSL bridge router a Cable Modem or a leased line router the VoIP Router allows you to use voice and fax services over IP in order to reduce the cost of all long distance calls The VoIP Router can be configured a fixed IP address or it can have one dynamically assigned by DHCP or PPPoE It adopts either the G 711 G 726 G 729A or G 723 1 voice compression format to save network bandwidth while providing real time toll quality voice transmission and reception VolP Wireless Router User s Manual 2 1 2 Hardw
14. Menu by opening a web browser e g Internet Explorer or Netscape Navigator and entering the factory default LAN IP address 192 168 8 254 Instructions eo Open a Web Browser e g Explorer Navigator Opera FireFox eo Enter the LAN port IP address in the address filed and press Enter The default LAN port IP address is 192 168 8 254 e The log in screen below will appear after you connect The factory default settings for Username and Password are left blank VolP Gateway C 192 168 8254 VY O i gt CATEUWAY The VolP Router does not allow multiple people to configure the VolP Router simultaneously Please remember to logout or restart the system if you are not using the web configuration function VolP Wireless Router User s Manual 9 2 1 Status 2 1 1 Current Status Status Current Status Refresh Time 2 308 pat Line Status Calls Number Proxy Register ras 51701 Idle 0 D D D 02 37 54 No Link FXS ol 702 Idle 0 D D D 02 37 54 No Link SIP Proxy Hunting Number Registration FXS D D D 02 37 54 Server Registration Status DDNS Registration Disabled 02 37 54 STUN Registration Disabled 02 37 54 For Port Status it includes if each port registers to Proxy successfully the last dialed number how many calls each port has made since the VoIP Router is start etc For Server Registration Status it shows the registration status of DDNS STUN and FXS Represent Number 2 1 2 RT
15. Shared Key Select the type of WPA PSK WPA PSK WPA2 PSK WPA2 Mixed PSK choose the proper security mode according to your wireless network WPA Authentication Mode Select Personal Pre Shared Key WPA Cipher Suite WPA Cipher Suite is used for the configuration of WPA or WPA2 Mixed TKIP TKIP is the security protocol used in WPA The length of TKIP encryption is longer than WEP encryption that increases the complexity of decoding for crackers AES The most powerful encryption algorithm that is commonly used in WPA WPA2 Cipher Suite WPA2 Cipher Suite is used for the configuration of WPA2 or WPA2 Mixed TKIP TKIP is the security protocol used in WPA The length of TKIP encryption is longer than WEP encryption that increases the complexity of decoding for crackers AES The most powerful encryption algorithm that is commonly used in WPA Pre Shared Key Format Select the Format of Pre Shared Key You can select Passphrase or Hex 64 characters by entering a character string ranging from A Z and 0 9 Pre Shared Key Enter a key of 8 64 characters long in the Pre Shared Key filed Make sure this key is exactly the same on all other wireless stations VolP Wireless Router User s Manual 44 Wireless Settings Security Settings eee Root AP SSID 4 Wireless Security Mode Wireless Security Mode WPA WPA Mixed w WPA WPA2 Mixed WPA Authentication Mode WPA Cipher Suite
16. each other FXS to FXS or 2 connect any phone port directly to a PSTN line FXS to PSTN or to an internal PBX line FXS to PBX extension 3 Stacking is forbidden Doing so may damage your VolP Router VolP Wireless Router User s Manual WPS WPS button for wireless WPS PBC setup method Antenna Connect to a wireless network Reset button Use to restore factory default settings Use Reset Button to restore factory default settings 1 Press and hold the reset button for 5 seconds 2 As Alarm indicator is blinking please release the reset button Factory settings will be restored VolP Wireless Router User s Manual 5 GW 532FW Front Pannel Indicators Power Power LED A steady light indicates a proper connection to a power source Prov Alm A blinking light indicates the VolP Router can not register with SIP Server or can not get the IP address A blinking light also indicates the VolP Router is attempting to connect with the Provisioning server Once the service connects the LED will turn off The LED will light solid red if the self test or boot up fails Reg The Register LED will turn on and continuously working when VolP Router is connected to a VolP service provider The LED will flash if not connected to a service provider WAN When a connection is established the LED will light up solid The LED will blink to indicate activity If the LED does not light up when a cable is connected verify the cable conn
17. separated wireless network For security you should change the default SSID to a special ID Wireless Channel Select a clear and appropriate channel for your wireless network A device on your wireless network must use a specific channel to transmit and receive data If wireless network has overlap change a different channel number 802 11 Mode The VolP Router can operate in 2 4GHz ISM band with different speed of wireless connection Select the wireless band of your network 802 11b only Allow all 802 11b compliant wireless devices to associate with the wireless AP 802 11g only Allow all 802 11g compliant wireless devices to associate with the wireless AP 802 11n only Allow all 802 11n compliant wireless devices to associate with the wireless AP Mixed 802 11g and 802 11b Allow a mix of both IEEE802 11g and 802 11b compliant wireless devices to associate with the wireless AP Mixed 802 11n and 802 11g Allow a mix of both IEEE802 11n and 802 11g compliant wireless devices to associate with the wireless AP Mixed 802 11n 802 11g and 802 11b Allow a mix of both IEEE802 11n 802 11g and 802 11b compliant wireless devices to associate with the wireless AP Mode The VolP Router has ability to serve as four operating modes in wireless network separately AP As a wireless AP that allows wireless equipped stations to communicate with a wired network and the other wireless network for Internet access and resources sharing Cli
18. switch or router Note VoIP router allows alternative Copper or Optical WAN at the same time 1 Ifyou connect Copper WAN at first that Optical WAN will not take active unless remove RJ45 cable from Copper WAN port 2 Ifyou connect Optical WAN at first that Copper WAN will not take active unless remove fiber from Optical WAN port 7 Ground A conducting connection with the earth Connect with the ground so as to make the earth a part of an electrical circuit using metal wire 8 Power Receptor Receptor for the provided power adapter 9 Power Switch Press down to turn on VoIP Wireless Router WARNING DO NOT 1 connect the phone ports to each other FXS to FXS or 2 connect any phone port directly to a PSTN line FXS to PSTN or to an internal PBX line FXS to PBX extension 3 Stacking is forbidden Doing so may damage your VolP Router VolP Wireless Router User s Manual WPS WPS button for wireless WPS PBC setup method Antenna Connect to a wireless network Reset button Use to restore factory default settings Use Reset Button to restore factory default settings 1 Press and hold the reset button for 5 seconds 2 As Alarm indicator is blinking please release the reset button Factory settings will be restored VolP Wireless Router User s Manual 8 2 VolP Wireless Router Web Configuration The VolP Router allows users to configure its settings using a web interface Web Ul You can access the Configuration
19. tone volume It will apply to all tones generated by the VoIP Router including Dial Tone Ring Back Tone and Busy Tone FXS Current Set the output D C current of FXS port Flash Time Enter the minimum flash time for FXS detecting When the flash signal generated by the phone set is shorter than Min FXS Hook Flash Time FXS port will be on hook Enter the maximum flash time for FXS detecting When the flash signal generated by the phone set is longer than the Flash Time FXS port will be on hook Polarity Reversal Check the box to activate the generation of polarity reversal from FXS FXS Chip Option 1 Check the box to avoid mis detecting the loop state of a subscriber line or PBX user loop from FXS interface In some cases the off hook voltage might cause the FXS interface mis detect the idle and the active state in order to avoid this situation un check this feature VolP Wireless Router User s Manual 32 General Settings Line settings Ring Early Media Time Limit 10 600s Enable End of Digit Tone Early Media Treatment Loop Current Drop Trigger Time o O disable 3 308 Loop Current Drop Duration 1 55 ROH Begin Time O disable 1 999s ROH Duration 5 FXS Ring Voltage o 45 80 FXS Onhook Voltage o 24 57 VoIP Centrex Extension Digit Count o 0 disable 1 30 VoIP Centrex Digit Metering Pulse Type Metering Pulse Period Ring Early Media Time Limit 10 600secs Enter the tim
20. 3000 congestion Tone 45 i 250 Busy Tone 5 500 Ring Back Tone ld CPT 2 Tone Type High Frequency Dial Tone E E Congestion Tone Busy Tone Ring Back Tone Tone Type Low Frequency High Frequency FWD DND Dial Tone 400 lo CPT 1 Enable Setting 1 The CPT has a set of parameter table Please adjust the CPT based on the local PSTN or PBX settings and requirements Advanced Settings CPT Cadence FXS Ring Cadence Settings ect FF MH 2 a FE 3 Range ON_1 One i ON 2 OFF_2 ON 3 OFF_3 250 8000ms 200 8000ms o 250 8000ms 0 200 8000ms 0 250 8000ms 0 200 8000me Poo i000 o o Al 1500 500 1500 FXS Ring Cadence Settings Specify the ring cadence for the FXS port In this field you specify the on and off pulses for the ring The ring cadence that should be configured differs depending on local PSTN or PBX settings and requirements VolP Wireless Router User s Manual 61 2 5 5 Provision Settings Provisioning is a function that automatically updates your VoIP Router s configuration by using a TFTP FTP or HTTP server located on the Internet If you have access to such service you will need to know the URL or IP address of the Provisioning Server Note Fill in the parameters needed by your VoIP Service Provider Please check with your VoIP Service Provider about the availability of these services Advanced Set
21. Centrex Extension Digit Count Metering Pulse Type Metering Pulse Period It is used for telephony device which connected to FXS port for billing purpose VoIP Router provide Polarity Reversal 12k Hz and 16k Hz metering capacity The fully support for detail Metering Pulse Period is not free charge please contact with your vendor VolP Wireless Router User s Manual 33 General Settings Line settings Termination Impedance Drop Inactive Call Silence Detection Threshold o O disable 1 60d0B Drop Silent Call Timeout o _ 0 disable 1 3600s Voice Menu Options Enable IVR Option FXS FXO Impedance Select different impedance from the drop down menu Drop Inactive Call This feature is a call drop standard for a VoIP Router to determine whether or not to hang up the phone The VoIP Router will disconnect the call automatically to avoid keeping the line engaged if the detected volume is below the Silence Detection Threshold or the time exceeds the Drop Silent Call Timeout Silence Detection Threshold Enter the threshold dB to detect if there is voice coming from RJ 11 interface Drop Silent Call Timeout Enter the duration second for detecting if there are RTP packets receiving from IP network Note Improper values for above settings might cause unexpected automatic disconnection of a call Default values are recommended Enable IVR Option Check the box to enable IVR function General Settings Lin
22. Choose homegroup and sharing optiogy 7 Connect to a Network Access files and printers located on oth eee EE Troubleshoot problems Do you want to set up your network Diagnose and repair network problems This 5 a new router that has not been set up Click OK to start setup Enter the 8 digit PIN from VoIP Router label then click Next T Set Up a Network rT g To set up a network type the 8 digit PIN from the router label You can find the numeric PIN on a label attached to the router or in the printed information that came from the manufacturer Cancel VolP Wireless Router User s Manual Type network name SSID then click Next cc o Set Up a Network Give your network a name Your network needs a unique name so that it can be easily identified It is best to keep the name short 25 characters or less and recognizable Security enabled networ Y Security twork Your network ts being set up using WPA2 Personal Change passphrase security level and encryption type advanced Cancel 92 VolP Wireless Router User s Manual 53 Configuration finished you could connect to VolP Router at present You could also print security key of save this profile for another computer to add this wireless network manually Ey ChangThird WIN7E_Network has been successfully set up To add an older wireless device to this network you might n
23. Configurations and click Restore Note You have to save settings and restart and all settings will take effect VolP Wireless Router User s Manual TT 2 7 5 System Log System settings System log C Enable Enable Check the box to send event notification messages across IP networks to the Server Server Address Enter the System Log Server s IP address Port Enter the System Log Server s listening port Leave this field to the default if your VolP Service Provider did not provide you a server port number for System Log Server 2 7 6 Save Restart Save and Reboot System settings Backup and Restore C Save Settings Restart Save All Settings Click the Save All Settings check box and reboot the system after completing changes The new settings will take effect after the VolP Router is restarted Restart Click the Reboot button to reboot the system VolP Wireless Router User s Manual 78 2 7 7 Software Upgrade The VolP Router supports a software upgrade function from a remote server Please consult your VolP Service Provider for information about the following details System settings Software upgrade Current Version 1 02 38 57 Ubgrade Server TFTP Server IP Address Server Port 1 65535 Directory Upgrade Server Select the upgrade type TFTP FTP or HTTP Software Upgrade Server IP Enter the server s IP address Software Upgrade Server Port Enter the server s po
24. DNS Group DynDNS DONS Server DynDNS DONS Server Server Address members dyndns org Hostname dyndns org Login ID Password eeeeeeeeee Behind NAT C Custom Enable Dynamic DNS Check the box to enable DDNS function It is only necessary when the VoIP Router is set up behind an Internet sharing device that uses a dynamic IP address and does not support DDNS Server address Accept the default setting or fill a correct DDNS Service FQDN Hostname Enter the URL of the system or NAT applied from domain name registration providers e g VolPGateway01 dyndns org Username or Key Password or Key Enter the Login ID and password used to log in to the DDNS server Note If the VoIP Router is set up under NAT then enter the hostname in the NAT IP Domain that is the same as the Hostname of the DDNS VolP Wireless Router User s Manual 67 2 5 10 NAT Traversal If your VolP Router is set up behind an Internet sharing device you can select either the NAT or STUN protocol Advanced Settings NAT Traversal NAT Public IP Enable STUN Client E Enable STUN Client Enable NAT Public IP Check the box to use the IP address of the Internet sharing device if the VoIP Router is set up behind an Internet sharing device Also the VoIP Router will use the IP address of the Internet sharing device as the public IP when it connects to Internet Furthermore some of the Internet sharing device s type is symmetri
25. Enable DoS Prevention Check the box to prevent DoS attacks from WAN There are various types of DoS attacking Leave settings in this field to the default if you are not familiar with it 2 5 12 DMZ ALG Advanced Settings DMZ ALG DMZ Demilitarized Zone allows the server on the LAN site to be directly exposed to the Internet for accessing data and to forward all incoming ports to the DMZ Host Adding a client to the DMZ may expose that computer to a variety of security risks so only use this option as a last resort Enable DMZ f r Host 1 Md aoc ALG C RTSP ALG Enable DMZ Check the box to enable DMZ feature DMZ Host IP Address Enter the IP address of that computer as a DMZ Host with unrestricted Internet access Note Either this function or virtual server can be selected for use in accessing external services RTSP ALG Enable ALG for RTSP multimedia stream VolP Wireless Router User s Manual 69 2 5 13 IP Filtering Advanced Settings IP Filtering Use IP Filters to deny particular LAN IP addresses from accessing the Internet You can deny specific port numbers or all ports for a specific IP address The screen will display well known ports that are defined To use them click on the edit icon You will only need to input the LAN IP address es of the computer s that will be denied Internet access Advanced Settings IP Filtering TCP UDP Both s
26. P Packet Summary Status gt RTP Packet Summary Line Codec The last packet s source IP The last packet s source Port Packet Sent Packet Received Packet Lost 1 56711udaw 64kbps o 0 D D 2 6 7 11udaw 64kbps o 0 D 0 Display the information of the last call made Press Refresh button to get the latest RTP Packet Summary VolP Wireless Router User s Manual 10 2 1 3 System Information Status System Information System Information Time and Date 2011 02 08 16 21 06 Firmware Version 1 2 38 66 215 WAN Port Information Factory Default MAC Address 001122334455 Net Link Connected IP address 192 168 1 141 Subnet mask 255 255 255 0 Default Gateway 192 168 1 254 Domain Name Server 192 168 1 200 LAN Port Information MAC Address 001122334456 IP address 192 168 8 254 Subnet mask 255 255 255 0 Wireless LAN Wireless Radio Wireless Network Name SSID 802 11 Mode Wireless Channel Wireless Security Mode DHCP Server IP Pool Range Lease Time Domain Name Server Hardware Platform Driver Enable SSID Mixed 802 1in 802 119 and 802 11b Auto Scan recommended hone Server Enabled 192 168 8 1 192 168 8 250 1 hour s 192 168 1 200 Hardware ON ZO 14 1 2 2 90 196 For WAN Port Information it shows IP address subnet mask default gateway and DNS server If you use PPPoE to obtain IP you will know if the IP is obtained through this method If I
27. P address subnet mask default gateway is blank it means that the VoIP Router does not obtain IP For LAN Port Information it shows LAN port IP subnet mask and the status of DHCP server For Hardware it shows the hardware platform and driver version VolP Wireless Router User s Manual 11 2 1 4 Routing Table Status Routing Table It displays routing table of VolP Router Destination Metmask Gateway 192 160 1 0 foo foo foto Ol 0 0 0 0 192 168 5 0 55 25 a Dl 0 0 0 0 default 0 0 0 0 192 166 1 254 2 1 5 LAN Client The DHCP Clients table displayed LAN device that has already been assigned an address from VoIP Router You can check if the DHCP client has obtain an IP address Status LAN Client Active Wireless Clients SSID MAC Address Tx Packet Rx Packet Tx Rate Mbps Power Saving Expired Time 5 SSID O00 13 e8 ched e1 795 1149 65 na 292 Dhcp Clients IP address MAC Address Live Time 5 19 2 168 8 1 00 13 e8 cf e6 e1 3212 VolP Wireless Router User s Manual 12 2 2 FXS Line Diagnostics 2 2 1 FXS Outward Test FXS Line Diagnostics gt Outward Test H F DC Voltage Hazardous and foreign DC voltage H F AC Voltage Hazardous and foreign AC voltage H F DC Voltage H F AC Voltage Tip Ring Short Failed d Enforced Test Ignore Port State It allows operator to verify whether it is some problem on the cable between Phone Sets and VolP Router Enable Select the lines you want to te
28. VolP Fiber Optical Router User s Manual Version 1 0 July 2011 Contents TINTO UCUON ii os 1 1 1 Produc t OvervieW sonnera a lost ata ty 1 1 2 Hardware Desc a eae ian eee eee 2 2 VoIP Wireless Router Web Configuration c sccccssssseeeeeeseeeseseeseesneeesneseesscasneesenseeeeesaessoeeseseseneneessaeneessons 8 O E En 9 A EENEI cee en A A A ee ee en er eae ey eee 9 Aa KOU LINAC Y cpt oe ote e Greta cca a E nese ae ate ah ea daca Sawa eee stance Pouce ages cece ae 9 Pere eo EE O ela pro do eea niece err PS 10 A NA A O 11 SEAN A ee ere Ree enn ee eee nee a ee ee en nee reece ce ne ee eee 11 222 FXS LING Dia gn OS se de 12 22 FXS OutWard Tes suet a ac cele a ata scant hla AE 12 2 2 2 FXS Inward Sell e da 13 2 3 GEN Settings e 14 2R WAN a a o 14 2 2 AN a al alas 18 DS O Peroa ete ee used eae eect a each cae setae bob eters bd rte E E hater Reda des 20 27 EOI AVANCES eee et eee eee AS A er ene 25 2330 Cali AA Ad 29 2350 HOLEN G e a 30 A a a E a a metemeaalt 31 DOO aeo ana E E a E E a a ayaa aaa 34 239 CallinG F earo secetes lactated atcta she nevaalshases wanduicionedelsedeadsuaacsoniivacendsdatssasiecusmleaten ested aie iedodueaeena sadness 36 2 3 1 0 MONG BOOK ae 38 2 07 WAGER SC WIN Os arnar an a och d natal ince O e a a e sitar tel aban a 39 BPA Wireless SOTUINGS sehen an a a E aa svat vs deaceauasieneweistarne diese E 40 2121 BASIC SS Ins A A A ae 40 2 A Z AVANCE SENGS il a ai 42 2123 9 POUM SCI OS trol cota 42 A Oa
29. VolP Router does not response to any access rules You are not allowed to make configuration changes on this page Allow Listed When Allow Listed is enabled only those wireless clients whose MAC addresses are in the Access Control List have rights to connect to your Access Point Deny Listed When Deny Listed is enabled only those wireless clients whose MAC addresses are in the Access Control List will be blocked and restricted access to your Access Point MAC Specify the MAC address which you want to allow deny access your Access Point Comment The space is reserved for comment or notation VolP Wireless Router User s Manual 46 2 4 5 WDS Settings The WDS feature can make connection wirelessly between two access points To add one more access point the range of the network can be extended Wireless Settings WDS Settings Enable WDS This Feature Needs Fixed Wireless Channel Encryption None Ww Statistics Tx Packets Tx Rate Mbps Enable WDS Click the Enable WDS check box to enable wireless bridging and repeating operation Encryption Select the encryption type WEP or WPA Wireless Settings WDS Settings V Enable WDS This Feature Needs Fixed Wireless Channel Encryption eros Mi WEP Key Format ASCII 5 characters we WEP Encryption Key Encryption Select WEP 64 WEP Key Format Select the preferred WEP Key Format according to which WEP encrypt
30. Wolume Dial Wait Timeout Enter the timeout duration after the user picks up the phone set Inter Digits Timeout Enter the timeout duration between the intervals of each key pressed When exceeding the set timeout duration without entering further digits the numbers entered will be dialed out Minimum DTMF ON Length Dial on Minimum DTMF OFF Length Dial off between tones This variable is to set the length of DTMF playback DTMF Detection Sensitivity This variable is to set the sensitivity of the telephone keys for the VolP Router to detect the DIMF DTMF Output Volume Adjust the Tx volume of FXS port for DTMF Caller ID or Out of Band DTMF Pulse Dial Mark Space Ratio Duration and break of pulse dial ration FXS Pulse Detection It allows FXS detect PULSE dial method sends from a phone set Enable Out of Band DTMF This variable is to set the method of DIMF transmission RFC2833 or SIP Info Note Out of Band DTMF transport method varies from VoIP networks please contact your VoIP provider for the preferred method Enable Hook Flash Event Select Auto RFC2833 or SIP info for the signaling method of Hook Flash Event Payload Type payload type of RFC2833 Volume Select the volume of RFC 2833 from the drop down menu VolP Wireless Router User s Manual 60 2 5 4 CPT Cadence Advanced Settings CPT Cadence CPT 1 Tone Type Low Frequency High Frequency T_ON_1 FAA 1 T ON 2 TAO 2 Dial Tone Laso
31. XS port of the VoIP Router and the FLASH button does not function please adjust the settings in Flash Detect Time from Advanced Options section Note The availability of the above features also depends on your VoIP network Please also check with your service provider for these services VolP Wireless Router User s Manual 38 Examples of establishing a Three Way call 1 Phone1 dials to Phone2 Phone2 answers the call 2 Phone presses Flash then calls Phone3 Phone2 is on hold and Phone3 answers the call 3 Phone presses Flash to start the conference call Or 4 Phone dials to Phone2 Phone2 answers the call 5 Phone presses Flash then calls Phone3 Phone2 is on hold and Phone3 answers the call 6 Phonel presses Flash and dial 3 to start the conference call Note The availability of a Three Way call also depends on your VoIP network Please also check with your service provider for these services 2 3 10 Phone Book Phone Book It is used for peer to peer communication Some peer information needs to be added to this section prior to making peer to peer calls You need to enter the phone number and the IP address of the remote peer General Settings Phone Book Gateway Name Gateway Number IP Domain Name Le 20 21 40 41 60 6l 60 1 100 Gateway Name Enter the alias of the remote peer Gateway Number Enter the phone number of the remote peer IP Domain Name Enter the IP address or URL
32. a a a nest a uamaa Geant euch eluent aman E teach x ccamhlvedia neckties 45 De AS ibe iia Satta eee emcee dea ea autnetaes olan othe sentences ates esta en ante ae ae chaeer tec 46 LAO SE SIN Sy eases ee ea eer ane loietis a te ae a A seesaw needa a ve ae archaea tec 48 A ee ene aati O 48 2290 AdVanesd LING Sisa ile 54 2 GON adietan pls eatsaicetnted balms treat Salata pad Saat the aes see cea eeatirentalaele 54 A A RT Te ee Oren een ae me en ae RT Sra ete Se a Pee a SECT ee een ares 55 rato ro Wy OIMFAPULSE le 59 aoe AS A A A 60 SS a o A A 61 229 0 Galler Pla tn coil ici 63 E Ue ROUTO AA A A a 64 2250 QOS SE nn sats aR a a tet anddcateabun cago les 65 20 IDDN S oera a a a a a 66 2S1 ONAT MVE Salario 67 2 5 11 DOS Protection Setting aina a a a aia a aia a E aA 68 22012 DMZ ALG rimia T A A ne eet ee 68 AAA a a a a a a a a 69 SE A aa A S 70 230 MAC FIKEN triada da aida 70 2 916 Virtual Se Vea O a 71 Be We A ir ER OO POSO CUE E ee eens ene sede ena ace ee cee ee 71 ONO aaa 12 OPW NAC eta tai 12 22 NONI a at apo 73 AS SU IM E e EEE A A A EEE 74 A ote dna ena saou onsets 74 Z Mert O A O EN 14 a e E 15 ZAC RO TOM Ciscoe ects assed a eTa 76 AS A A e N EE o EE E nn An 17 A A A o it o ad aes ieee teopeaaneeenidas seealen 17 TES a 78 E ig OO 0 8 NOR een eA A e uo ee eee ere ere E ree eT 78 3 Configuring the VoIP Router through IVR ccccssceceseeeeeeeeseeesseeneeeeeasseeseasneeeseseesseanaeeeeasneesenaneessenensessoanneess 79 3 1
33. and Server 1 as the last route The number look up flow appears like Digit Map Server 2 Server 3 Server 1 Table VolP Wireless Router User s Manual Start Enter a phone number D Is DF defined in Speed Dial table Dial the number Yes defined in Speed Dial table No Is D defined in Extension table Yes No Is D defined in Phone Book table Yes No Is DH defined in Phone Book Yes Manager No Is D defined in SIP Yes proxy server Dial out as defined in the first match case through the gateway Dial D through Does this the first available gateway have an FXO port to PSTN FXO port End
34. are Description GW 522FW Front Pannel Indicators Power Power LED A steady light indicates a proper connection to a power source Prov Alm A blinking light indicates the VolP Router can not register with SIP Server or can not get the IP address A blinking light also indicates the VolP Router is attempting to connect with the Provisioning server Once the service connects the LED will turn off The LED will light solid red if the self test or boot up fails Reg The Register LED will turn on and continuously working when VolP Router is connected to a VolP service provider The LED will flash if not connected to a service provider WAN When a connection is established the LED will light up solid The LED will blink to indicate activity If the LED does not light up when a cable is connected verify the cable connections and make sure your devices are powered on WLAN A steady light indicates a wireless connection A blinking light indicates that the VolP Router is receiving transmitting from to the wireless network LAN When a connection is established the LED bottom will light up solid on the appropriate port The LEDs will blink to indicate activity If the LED does not light up when a cable is connected verify the cable connections and make sure your devices are powered on USB This indicates that VoIP Router detects a supported 3G modem dungle or a USB device Phone This LED displays the VolP status and Hook Ringing act
35. ary IP address of Domain Name Server if Domain Name Server Assignment is Manual Otherwise the VolP Router will not be able to access hosts using hostnames instead of IPs General Settings LAN VolP Wireless Router User s Manual 19 LAN Port Control Port Enable Port Incoming Rate Limit Outgoing Rate Limit NAT Bridge VLAN ID LAN Port 1 Fuil se Ful MAT se ig LAN Port 2 Zy r El w MAT LAN Part 3 ul s Ful Ww MAT LAN Part 4 Ful we Ful Me MAT e Enable Port Tick the box to enable LAN Port Incoming Rate Limit Use the drop down menu to select the proper rate limit for the specific LAN port The flow is from LAN to WAN and the rate limit can not exceed the real upstream bandwidth Outgoing Rate Limit Use the drop down menu to select the proper rate limit for the specific LAN port The flow is from WAN to LAN and the rate limit can not exceed the real downstream bandwidth NAT Bridge Select the VoIP Router serving as a Router with NAT or Bridge between WAN port and LAN port without NAT VolP Wireless Router User s Manual 20 2 3 3 SIP As there are various Proxy Server providers according to RFC standard it has designed the gateway to be compatible with them If any registration problem occurs please consult your Internet telephony Server Provider General Settings SIP Soft Switch Setting Enable Support of SIP Proxy Server Soft Switch ITSP Name Enable Support of SIP Proxy Server
36. c NAT You need to set Virtual Server or Port Mapping Forwarding from the Internet sharing device for the listen port and communication ports RTP ports of the VoIP Router NAT IP Domain Enter the real public IP address of the IP sharing device or the router or enter a true URL Uniform Resource Locator when DDNS is used Please refer to the DDNS settings Note If you are setting a public IP in this field it has to be a static public IP otherwise VoIP communication may not be established properly Please contact your ISP to check if your Internet connection has static public IP addresses Enable STUN Client Check the box to use the STUN protocol prevents problems from setting the IP sharing function Some NATs do not support this protocol Note You can use the Status gt STUN Inquiry page to detect the NAT type of your Internet sharing device If the NAT type is Symmetric NAT then the VoIP Router is not able to traverse the NAT It is not a flaw of the VoIP Router design but rather a limitation of the STUN protocol STUN Server IP Domain and Port Enter the IP address and listen port of the STUN server You can set two STUN server IPs separated by a semicolon VolP Wireless Router User s Manual 68 2 5 11 DoS Protection Settings Advanced Settings DoS Protection Settings Enable DoS Protection Whole System Flood s Packets Second 50 500 TCP Scan Ping of Death ICMP Smurf IP Spoof Oe a O
37. d dial 2301 The VoIP Router will dial 35106301 and follow Route 2 VolP Wireless Router User s Manual 58 For example Scan Code 0 VolP Dial out 1805 User Dial Length Disable Route VolP VoIP Route Profile Route 3 Digitmap Scan Code Route O Pick up the handset and dial 0423456789 The VoIP Router will dial 1805423456789 and go through Internet first and follow Route 3 Method 3 Substitution It helps you dial to destination that you can not dial by phone Destination like test 1 1 1 1 Fill in the number into the Scan Code column and enter the desired name into the VoIP Dial out column For example Scan Code 11 VoIP Dial out test User Dial Length 2 Route VoIP VoIP Route Profile Route 1 Digitmap VoIP Dial out Pick up the handset and dial 11 The VoIP Router will dial test and go through Internet and follow Route 1 VolP Wireless Router User s Manual 59 2 5 3 DTMF PULSE Advanced Settings DIMF amp PULSE Dial Wait Timeout 10 1 602 Inter Digits Timeout 4 1 605 Minimum DTMF OW Length an 40 500 ms Minium DTMF OFF Length ao 20 500 ms DTMF Detection Sensitivity 3 se DTMF Detection Volume Sensitivity O w DTMF Output Volume 0 e Pulse Dial Mark Space Ratio US 61 39 Y v FXS Pulse Detection Enable Out of Band DTMF Out of Band DTMF AFC 2633 O SIF Info Enable Hook Flash Event Disable Payload Type
38. ders VolP Wireless Router User s Manual 26 General Settings SIP Advanced Session Timer Session Expiration T 0 disable 10 1800 5 Session Refresh Request UPDATE C re INVITE Session Refresher HAS UAC Session Expiration This field will set the time that the VoIP Router will allow a SIP session to remain die without traffic before dropping it Session Refresh Request Select UPDATE or re INVITE to send refresh requests to the Server Session Refresher This determines which side of an expired call session will initiate the session refresh uac specifies that the Caller side will initiate the session refresh uas specifies that the Call receiver the Callee will initiate the session refresh General Settings SIP Advanced SIP Timeout Adjustment SIP Message Resend Timer Base Max Response Time for Invite SIP Message Resend Timer Base Select the resend timer base from the drop down menu if response is not received within the base time The sequence of sending is like base time 2 and send again at base time 2 2 The maximum resend time is four seconds Resend action will stop when the total resend time has reached 20 seconds Max Response Time for Invite Enter the maximum response time for INVITE packet When the destination does not reply within the set time the call is failed General Settings SIP Advanced SIP Proxy Server Soft Switch Settings C
39. digits conversion information is provided in the PPPoE Character Conversion Table When correct IVR passwords are entered and accepted an indication tone can be heard indicates the system is in IVR setup mode Enter function codes to check or configure the VoIP Router Example If your password is 1234 enter star star 1 2 3 4 pound and now you are entering IVR setup mode Next enter a function code to check or configure the VoIP Router If your password is admin enter star star star 41 44 53 49 54 pound Please refer to the IVR Functions Table page 68 for available functions and codes Once the setting or query has been completed you can hear a dial tone Use the same procedure to make a second query or setting To exit IVR mode simply hang up the phone Example enter you are now in IVR mode gt enter 101 to query the current IP address gt the system responds with an IP address You can continue with more settings or queries enter 111 to seta new IP address Senter 192 168 1 2 new IP address VolP Wireless Router User s Manual 80 Save Settings When all setting procedures are completed dial 509 Save Settings from phone keypad Wait for about three seconds you should hear a voice prompt 1 one You can now hang up the phone and please reboot the VolP Router to enable the new settings To inquire about the current VoIP Router WAN Port IP address setting After completi
40. e VolP Router provides the registration for multiple VolP Service Providers and each VSP has a private digit map Hence the routing and number translation may vary We use two part Routing and Number Translation to explain the dialing principle of the VolP Router Dialing Options 1 Dial the phone number which you want to call and press to call out immediately Note that if the pound not dialed the number will be called out after 4 seconds by default The period between number dialed and call out is named Inter Digits Timeout Configurable from DTMF default 4 seconds see page 55 2 Ifthe phone number matches a rule of Digit Map Table the phone number will be routed the assigned VSP or Phone Book according VolP Route Profile automatically Number Translation Phone number is dialed by user The system will check if the phone number is matched Digit Map Table If no matched is found from Digit Map Table it will use the phone number to look up private digit map of the server set in VolP Routing Profile The system will translate the phone number to global number used to look up private digit map of the server set in VolP Routing Profile Enter a phone ls DR No Is D defined in No Start gt number DH e gt Private Digit Map ap table Table Translate D to global Translate D to number based on Digit private number based Map Table on Private Digit Map Yes Is the global numb
41. e settings FXS Group Hunting Ring Priority Hunting Ring Hunting Ww Sequential Ring Time je 1 1008 Hunting Ring It is used to set FXS group hunting mode There are Hunting Simultaneous Ring and Sequential Ring Hunting When someone calls in by dialing FXS representative number the system will always assign the call to the first line Simultaneous Ring When someone calls in by dialing FXS representative number all FXS ports will ring at the same time Sequential Ring When someone calls in by dialing FXS representative number the system will assign the call to each FXS ports in order according Sequential Ring Time You can adjust Sequential Ring Time for the ring time of each port VolP Wireless Router User s Manual 34 2 3 8 FAX General Settings FAX Fax Modem Line 1 T 38 Fax Ss Disable Select it if you are not sending fax but it is still accepted fax by the VoIP Router T 38 Fax Select it if you are using T 38 as the protocol for fax transmission T 38 is used for reliable and efficient facsimile transmission over network It transmits and receives FAX waveform relaying over the codec negotiated during call setup this bandwidth consumed is lowered T 38 protocol also supports redundancy to get better FAX quality T 30 Fax Select it if you are using T 30 as the protocol for fax transmission It transmit FAX signal as voice thus uncompressed G 711 would be the choice G 726 also wor
42. ealm SIP Domain and Use Domain to Register are the parameters provided by VoIP Service Provider If you fail to make a call please contact your VoIP Service Provider Bind Proxy Interval for NAT Check the box to keep the binding exist by sending packets when the VoIP Router is behind a NAT and SIP proxy server is not able to keep the binding Initial Unregister Check the box to send an unregistered message initially by the VoIP Router and then it will perform a general register process Unregister All Contacts VolP Router sends un register request to SoftSwitch which the contact field filled with a start sign to un register all FXS in this VoIP Router Keep SIP Auth VoIP Router keeps the last register SIP MD5 authentication information and re use it for next register request Support Message Waiting Indication MWI It is used to enable disable Message Waiting Indication It is available only when Voice Mail Service is available from the VoIP Service Provider MWI Subscribe Interval It is used to set the subscribe time for the VolP Router to check the voice mail VolP Wireless Router User s Manual 23 General Settings SIP Outbound Proxy Support C Outbound Proxy Support Outbound Proxy Support Check the box to send all SIP packets to the destined outbound proxy server An outbound proxy server handles SIP call signaling as a standard SIP proxy server would do Further it receives and transmits phone conversation traf
43. ections and make sure your devices are powered on WLAN A steady light indicates a wireless connection A blinking light indicates that the VolP Router is receiving transmitting from to the wireless network LAN When a connection is established the LED bottom will light up solid on the appropriate port The LEDs will blink to indicate activity If the LED does not light up when a cable is connected verify the cable connections and make sure your devices are powered on USB This indicates that VoIP Router detects a supported 3G modem dungle or a USB device Phone This LED displays the VoIP status and Hook Ringing activity on the phone port that is used to connect your normal telephone s If a phone connected to a phone port is off the hook or in use this LED will light solid When a phone is ringing the indicator will blink WPS Flashing in blue as wireless router processing WPS PBC wireless connecting progress VolP Wireless Router User s Manual 6 Rear Panel 1 WLAN Switch Switch it to power on off wireless feature 2 Phone Port 1 2 Connect to your phones using standard phone cabling RJ 11 3 USB Connect to a 3G USB dungle or a printer 4 LAN 10 100 1000M Gigabit Ethernet Connect to your Ethernet enabled computers using Ethernet cabling 5 Copper WAN 10 100 1000M Gigabit Ethernet Connect to your broadband modem using an Ethernet cable 6 Optical WAN Insert 100M 1000M fiber optic SFP module and connect to a
44. eed to provide this security key You can print these network settings for future reference For gaming consoles or computers running Windows XP co easier set up Close Note VoIP Router supports WPS work with Windows Vista and Windows 7 only VolP Wireless Router User s Manual 54 2 5 Advanced Settings 2 5 1 Codec setting Advanced Settings gt Codec settings Jitter Buffer 120 60 1200ms Silence Detection Suppression Echo Cancellation Enable RTCP XR RFC 3611 Enable Codec Packet Interval ms Approximate Bandwidth Required kbps LI d G 71Ludaw a 20 e 85 8 6 7231 29 6 723 16 3 30 Y 20 8 G 726 32K 3 las 20 e 53 6 G 729 Ba 20 e 29 6 6 711 ataw so 20 85 6 GSM E 20 e 34 8 Jitter Buffer Enter the jitter of receiving packets Silence Detection Suppression Check the box to enable the silence packets and send less voice data package during the silent period while talking Echo Canceling Check the box to remove echo and improve voice quality during conversation Enable RTCP XR RFC 3611 Enable RTCP XR RFC 3611 to report network quality Codec Check the box to codec for the VolP Router to support All codecs are selected and supported by default You can un check the box that is not used Codec Priority The priority of code for communication Packet Interval Select the frame size of voice package from different codec It defines the ti
45. ent As a wireless client you are allowed to access Internet via an Access Point in infrastructure mode or build a group of wireless network for files and printer sharing in ad hoc mode WDS WDS Wireless Distribution System mode is referred to as bridging mode to provide wireless VolP Wireless Router User s Manual 41 AP to AP connectivity in which allows two LAN network to make a connection without the need of a wired backbone to link them WDS AP is deigned to communicate with a specific AP and do not accept wireless stations to access them AP WDS AP WDS mode is performing as a wireless repeating in which Access Points communicate with each other wirelessly and accept wireless stations to access them at the same time Network Type Select network type for Access Client Mode Infrastructure Connect to another wireless AP or WISP Ad hoc Connect to another wireless Ad hoc device Usually it is used for peer to peer connect mode Channel Width Wireless channel width for 802 11n Select 40 MH for higher speed Broadcast SSID Broad AP s SSID for convent usage To hid SSID for more security Enable WMM Wi Fi Multimedia It provides higher priority for multimedia stream to get better quality Enable Universal Repeat Mode Set VolP Router to be wireless repeat mode Please fill the same SSID as the root AP in SSID of Extended Interface SSID of Extended Interface Enter the SSID of the root AP Wireless Settings Basic Setting
46. eout to cancel a call if no one answers the phone Enable End of Digit Tone Check the box to activate the function of playing a Beep Beep tone to notify the user that the call is in progress Early Media Treatment Check the box to send the one way RTP immediately when a connection with a VolP service provider has been set up Loop Current Drop Trigger Time Enter the time to avoid the line being engaged when FXS port is connected to PBX It stops the loop current from FXS port when FXS port is playing busy tone The setting 0 zero is to disable this function Loop Current Drop Duration Enter the drop duration for loop current ROH Begin Time As users forget hang up phone set it makes FXS play loud Howler Tone to notify users put hand set correctly If this timer is set to be 20 seconds that FXS play busy tone for 20 seconds then play ROH ROH Duration It is the maximum time for FXS play ROH then FXS will stop play ROH and keep silence FXS Ring Voltage It is to set the Ring Voltage of FXS FXS Onhook Voltage It is to set the Onhook Voltage of FXS VoIP Centrex Extension Digit Count This feature is to enable and set the digit count of VoIP Centrex The setting 0 zero is to disable this function VoIP Centrex Digit Enter the digit for VoIP call If you dial VoIP Centrex Digit first the dialing plan is according to the Digit Map otherwise the VoIP Router will send the number which digit count is the same as VoIP
47. er defined in Private Digit Yes Translate the global number to private number based on Private Digit Map Dial out as defined in the first match End case by SIP TA VolP Wireless Router User s Manual 84 Routing To achieve maximum flexibility the number dialed will be looked up in several tables defined by the VolP Router If no match is found from Digit Map Table it will then look up the number from another table and to the registered VSP Routing Processing Flow The routing after checking Digit Map Table may be vary The routing is accord with VolP Route Profile By default Phone Book is the first route of VoIP Route Profile The second and third route is Server 1 and Server 2 Server 3 is the last route Each server has a Private Digit Map and the number will be translated according the Private Digit Map before dialing out For default setting the number look up flow appears like The routing after checking Digit Map Table may be vary The routing is accord with VolP Route Profile By default Phone Book is the first route of VoIP Route Profile The second and third route is Server 1 and Server 2 Server 3 is the last route Each server has a Private Digit Map and the number will be translated according the Private Digit Map before dialing out For default setting the number look up flow appears like Digit Map Phone Assume that the route of Default Route Profile is Server 2 as the first route Server 3 as the second route
48. etained Note If the system does not play back the IP address this indicates that the VoIP Router failed to communicate with a DHCP server Please check with your DHCP server or ISP Save Settings and Restart To save settings dial 509 Save Settings The system will save the settings Please restart the system Wait for about 40 seconds for the system to restart then enter 101 to check whether the IP address was retained If the system does not play back the IP address after dialing 101 this indicates that the VoIP Router currently is not connected to the Internet Please check and make sure the cable connections account numbers and passwords are correct VolP Wireless Router User s Manual 82 3 2 1 Character Conversion Table The table below provides a list of conversion codes The first row high lighted of each pair of the column lists the numbers alphabets or symbols and the second row high lighted of each pair of the column Input Key represents the codes to be entered for the corresponding numbers alphabets or symbols For example to enter admin according to the table below enter 148322495451 Numbers Input Key Upper Case Input Key Lower Case InputKey Symbols Input Key Letters Letters O ON DOA ON a O A B C D E F G H J K L M m N n O O P p Q q R r S E U V W X ne Z N Se Xi lt E 0 VolP Wireless Router User s Manual 83 4 Dialing Principles Th
49. fic media between two communication parties This option tells the VolP Router to send and receive all SIP packets to the destined outbound proxy server rather than the remote VoIP device This helps VoIP calls to pass through any NAT protected network without additional settings or techniques Please make sure your VoIP Service Provider supports outbound proxy services before you enable it Outbound Proxy IP Domain Enter the outbound proxy s IP address or URL Outbound Proxy Port Enter the outbound proxy s listening port General Settings SIP Enable P Asserted Enable P Assert Check the box to enable the caller ID protection Privacy Type It is used to disguise the caller ID when queried via an ITSP Third Party Assertion The Privacy Type includes user header session none critical id and history General Settings SIP Number Translation VoIP Dial Out defined here overrides Digit Map VoIP Dial out The rule of dialing of inviting to VoIP Service Providers may vary That is you have to configure different Digit Map for different VoIP Service Providers In this filed you can configure individual dialing plan for each VoIP Service Provider The following examples introduce some cases For general configuration refer to Digit Map page Note Press Add to add an entry Don t forget to press Apply which in the above of Number Translation VolP W
50. ion you choose When WEP 64bits is enabled you can select ASCII 5 characters and Hex 10 characters WEP Encryption Key You can manually input key value Type a character sting and apply changes For a 64 bit WEP key Enter 5 characters ASCII sting or 10 hexadecimal characters 0 9 A F VolP Wireless Router User s Manual A7 Wireless Settings WDS Settings Enable WDS This Feature Needs Fixed Wireless Channel Encryption WEP 128 v WEP Key Format ASCI 13 characters WEP Encryption Key E Encryption Select WEP 128 WEP Key Format Select the preferred WEP Key Format according to which WEP encryption you choose When WEP 128bits is enabled you can select ASCII 13 characters and Hex 26 characters WEP Encryption Key You can manually input key value Type a character sting and apply changes For a 128 bit WEP key Enter 13 characters ASCII sting or 26 hexadecimal characters 0 9 A F Wireless Settings WDS Settings Enable WDS This Feature Needs Fixed Wireless Channel Encryption Pre Shared Key Format Passphrase EA C O O O Encryption Select WPA or WPA2 Pre Shared Key Format Select Passphrase or Hex format Pre Shared Key Enter a password of 8 64 characters MAC XxIXxXIXKIXKIXXIXX VolP Wireless Router User s Manual 48 MAC Enter the MAC addresses of one or more Access Point in this filed fo
51. ireless Router User s Manual 24 For example Example in Taiwan If Server 1 is local VolP Service Provider you can refer to Digit Map page for general settings If Server 2 is global VolP Service Provider VolP STUN free to dial to some cities free charge you can set individual dialing plan for VolP STUN in Number Translation field Scan Code can be your dialing custom and VoIP Dial out is the number on the basis of the dialing rule needed by VoIP STUN Its dialing rule is Country code Area Code phone number When you make calls to Taipei through VoIP STUN you don t change the dialing custom just dial O2xxxxxxxx and the system will change the number from 02xxxxxxx to 8862xxxxxxxx The same rule is for 2 When you make calls to UK via VoIP STUN you ll dial 00244xxxxxx and the system will change it to 44xxxxxx The settings for Server 2 appear like NUMBER TRANSLATION YolP Dial Out defined here overrides Digit Map Copy From None Scan Code VoIP Dial out 02 aA 00244 44 If Server 3 is a VolP Service Provider in UK you can set individual dialing plan in Number Translation field As you make calls to UK through this VolP Service Provider Country code should be removed and plus 0 by the system The settings for Server 3 appear like NUMBER TRANSLATION VolP Dia Out defined here overrides Digit Map Copy From None Scan Code VoIP Dial out 00244 Oo VolP Wireless Router User s Manual
52. ivity on the phone port that is used to connect your normal telephone s If a phone connected to a phone port is off the hook or in use this LED will light solid When a phone is ringing the indicator will blink WPS Flashing in blue as wireless router processing WPS PBC wireless connecting progress VolP Wireless Router User s Manual 3 Rear Panel 1 WLAN Switch Switch it to power on off wireless feature 2 Phone Port 1 2 Connect to your phones using standard phone cabling RJ 11 3 USB Connect to a 3G USB dungle or a printer 4 LAN 10 100M fast Ethernet Connect to your Ethernet enabled computers using Ethernet cabling 5 Copper WAN 10 100M fast Ethernet Connect to your broadband modem using an Ethernet cable 6 Optical WAN Insert 100M fiber optic SFP module and connect to a switch or router Note VoIP router allows alternative Copper or Optical WAN at the same time If you connect Copper WAN at first that Optical WAN will not take active unless remove RJ45 cable from Copper WAN port If you connect Optical WAN at first that Copper WAN will not take active unless remove fiber from Optical WAN port 7 Ground A conducting connection with the earth Connect with the ground so as to make the earth a part of an electrical circuit using metal wire 8 Power Receptor Receptor for the provided power adapter 9 Power Switch Press down to turn on VoIP Wireless Router WARNING DO NOT 1 connect the phone ports to
53. ks but not recommended Due to this nature T 30 always requires a SDP change change of codec within a session SIP Re Invite required after FAX tone detected by the callee It will consume more network resources and will affect transmission quality The VoIP Router is still able to change the protocol from T 38 to T 30 if the called party uses T 38 for fax transmission T 30 Fax Modem Select it if you use it as the protocol for transmission of fax modem over IP network T 30 Only Select it if you are using G 711 a law or G 711 u law for fax transmission The VoIP Router won t accept T 38 for fax transmission T 38 Native Select it if you are only using T 38 for fax transmission T 30 V 152 As GW detect FAX tone it will change RTP codec to be T 30 codec directly without sending Re Invite to change codec Note When a fax tone is detected from the call the VoIP Router will automatically switch from voice mode to fax mode Hence the fax settings will be temporarily applied to a specific port which detects the fax tones instead of its default voice settings General Settings FAX C Switch FAX On CED Detection C Restrict T 38 FAX Detection Sensitivity Switch FAX On CED Detection VolP Router will send FAX Re Invite immediately as it detect FAX CED tone that will save handshaking time between FAX machines Restrict T 38 VolP Router will reject T 38 Re invite in case the FAX type contains without T 38 FAX Detec
54. lP call service TFTP Source Port Assign TFTP source port for TFTP download Note Contact your server provider if necessary Binding Server for Trigger Check the box to trigger a connection between Provisioning Server and the VolP Router Provisioning Server will bind a port for the VolP Router to send provision request Binding Port Enter the port number of Provisioning Server is used for binding Binding Interval Enter the interval at which the VolP Router will keep the binding VolP Wireless Router User s Manual 63 2 5 6 Caller Filter This function allows you to accept or reject any incoming call from the IP address listed in the filter rule The call from the IP address of SIP proxy server is always accepted despite Deny is selected or the IP address of SIP proxy server is not in the filter rule of Allow Advanced Setting Caller Filter Caller Filter Enable Filter IP address Subnet mask 192 166 0 21 cando dan E E Caller Filter It is to allow or deny the filter rule Status It is to show the status of enable or disable Filter IP Address Enter the start IP address which you would like to Allow or Deny Subnet mask Enter the subnet mask you would like to Allow or Deny VolP Wireless Router User s Manual 64 2 5 7 Static Route Build static routes within an internal network These routes will not apply to the Internet Advanced Settings Static Route Route Mask Next Hop IP Interface R
55. lay 0 disable 0 60s 1 FXS L 2 FXS dl Enable Tick the check box to enable a line If some lines are not used disable them Pause Function to avoid unnecessary waiting when an incoming call is diverting to the line Hot Line Check to direct the call automatically to a pre configured destination without any action when the FXS is off hook i e as the user picks up the phone When the FXS is under Hot Line mode no other phone numbers can be dialed Hot Line No Enter the number for pre defined destination Warm Line Enter the time for the call to start with a pause so the user can dial another number The call will be automatically directed to the pre configured destination within timeout period FXS Group When there is an incoming call and the gateway will automatically assign an unassigned call according to the Hunting Priority If Port 2 does not want to be set as an assigned line to receive any inbound calls the function can be disabled VolP Wireless Router User s Manual 31 Line Type 1 2 3 7 Line settings General Settings Line settings Listening Volume Speaking Volume 3dB per step 3dB per step FXS Current Tone Volume 18 48mA FXS Polarity Reversal FXS Chip Option 1 C al L Listening Volume Use the drop down menu to adjust the hearing listening volume Speaking Volume Use the drop down menu to adjust the speaking volume Tone Volume Use the drop down menu to adjust the
56. me interval for the VolP Router to send a RTP packet or voice packet to the receiving side The smaller the value the greater the bandwidth takes and larger values might cause voice delay Approximate Bandwidth Required lt shows the bandwidth required from different codec and packet interval VolP Wireless Router User s Manual 55 2 5 2 Digit Map Digit Map supports multiple dial plans which help users to arrange least cost route Each Proxy Server has individual dial plan which combines the original feature of Digit Map and Speed Dial You can use or in the column of Scan Code and VoIP Dial out represents a single digit and represents a wildcard The function of the signs is to mapping the numbers between the number received from user and the replaced or modified number for actual dial out With this function users can easily add certain leading digits to replace a full set of numbers There are 50 sets of leading digit entries to choose voice routing interface Advanced Settings Digit Map C Alert if Auto fails Enable Pound Key Function Max Dial Length 25 IK 1 30 Default Call Route Auto VoIP first Default VoIP Route Profile li iw Digit Map Mode Simple Alert if Auto fails Check the box to play a voice announcement before calling out It reminds the user that this call is through PSTN Enable Pound Key Function Check the box to treat as a digi
57. messages for both wireless stations In most case keeping the default value 2347 is recommended RF Output Power You can adjust the percentage of power 100 50 25 10 5 of your VoIP Router to change the coverage of wireless network Keep the default value 100 to reach full range 2 4 3 Security Settings Wireless Settings Security Settings Select SSID Root AP SSID Wireless Security Mode Wireless Security Mode Select SSID Select an SSID to configure wireless security mechanism Security Mode Select the encryption authentication type None WPA WPA2 and WPA WPA2 Mixed WPA Authentication Mode The wireless network can use WPA Authentication to verify whether a wireless device is allowed to access your Access Point or not You can choose to use Enterprise RADIUS method or Personal Pre Shared Key The encryption mechanism used for RADIUS and WPA PSK is the same The difference between the two is that WPA PSK uses a specific characters sting like password instead of a user authentication VolP Wireless Router User s Manual 43 Wireless Settings Security Settings Root AP 551D iw Wireless Security Mode Wireless Security Mode WPA Authentication Mode Personal Pre Shared Key e WPA Cipher Suite Tap aes r gt li l a 41 MITO EN A SLIDE Pre Shared Key Pre Shared Key Format Passphrase Ww Pre
58. ng all your settings dial 101 from the keypad then you can hear the system play back the current WAN Port IP address If the system does not play back the IP address after dialing 101 this indicates that the VolP Router currently is not connected to the Internet Please check and make sure the cable connections account numbers and passwords are correct 3 1 1 IVR Functions Table Function Description Example Notes Code 111 101 WAN Port IP address Set Query 1121102 WAN Port Subnet Mask Set Query Dial function code 114 and then dial 1 for a Static IP connection then 113 103 WAN Port Default Gateway Set Query setup the IP address 114 104 Current Network IP Access Set Query 1 Static IP 2 DHCP 3 PPPoE 116 106 Phone Book manager IP address Set Query 118 311 301 LAN Port IP Set Query 312 302 LAN Port Subnet Mask Set Query 109 Restore factory default IP address configuration 409 Restore factory default settings A D YN p a 509 Save settings VolP Wireless Router User s Manual 81 3 2 IP Configuration Settings Static IP Settings Note Complete static IP settings should include a static IP option 1 under 114 IP address 111 Subnet Mask 112 and Default Gateway 113 Please contact your Internet Service Provider ISP if you have any question Function Command Select a Static IP e After entering IVR mode dial 114 e When voice prompt plays Enter value dial 1 to select static IP
59. nter a MAC address to prevent the particular device from accessing the Internet Remark Enter comments VolP Wireless Router User s Manual 11 2 5 16 Virtual Server Enable users on Internet to access the WWW FTP and other services from your NAT It is also known as port forwarding When remote users are accessing Web or FTP servers through WAN IP address it will be routed to the server with LAN IP address Advanced Settings gt Virtual Server C Enable Virtual Server WAN Port Range TCP UDP LAN Host IP Address Server Port Range o Ho o L L a Bo o o D Enable Virtual Server Check the box to enable port forwarding WAN Port Range Enter the port range for the WAN side TCP UDP Select the communication protocols used by the server TCP UDP or Both LAN Host IP Address Enter the IP address of the device that provides various services Server Port Range Enter the port range used by the LAN host Remark Enter comments 2 5 17 UPnP Advanced Settings UPnP Enable UPnP Server UPnP is a network standard enables the auto discovery the devices on the network It only works with the device that supports UPnP VolP Wireless Router User s Manual 12 2 6 Tools 2 6 1 Ping Test Use Ping to verify if a remote peer is reachable Enter a remote IP address and click Test to ping the remote host The result would be shown on Result Table Tools Ping Test Ping
60. oE dial up ADSL PPTP a a a Methods for using DHCP and PPPoE for obtaining an IP address may vary If you are not familiar with creating a network connection please contact your local ISP After selecting the suitable option click Accept at the bottom of the screen to save the settings You need to save the changes and restart the VolP Router to make the changes active Enter System Settings gt Save Restart page then Save and Restart Wait for about 50 seconds before the VoIP Router obtaining an IP address by the method you selected Note When the system has obtained a new IP address and you are using a WAN port to enter the Web Configuration Screen the new IP address has to be used before you can get connected to the VoIP Router The same principle applies to the next two settings General Settings WAN WAN Settings C Enable VLAN Tagging VLAN ID Priority Enable Type WAN 1 Default Route WAN 2 C VolP Wireless Router User s Manual General Settings WAN Enable Default Route LI Hostname Vendor Class ID MTU WAN 1 Domain Name Server Domain Name Server Primary IP Domain Name Server Secondary IP DHCP Select this option if your ISP 15 WAN Settings Enable VLAN Tagging VLAN ID Priority E WAN 1 Settings a 1500 Manual ie nternet Service Provider provides you an IP address automatically Cable modem providers ty
61. om WAN Web UI auto logout 30 3005 Enable Web UI Enable Telnet Service Port of Web Access from WAN Enter the port number when accessing the web based configuration utility from the WAN port Web Idle Time Out Enter the range of effective time when log in the web interface The user will be disconnected from the web page to allow others to log in Enable Web Ul Check the box to enable WEB access from WAN or LAN Enable Telnet Service Check the box to enable Telnet access from WAN or LAN VolP Wireless Router User s Manual 76 2 7 4 Backup Restore Backup Configurations File System settings Backup and Restore Backup Configurations Configuration File Wireless Configuration File Configuration Template File The current system settings can be saved as a file onto the local hard drive Click the Backup Settings button to save your current settings to a file Configuration File lt is to backup the all settings Wireless Configuration File It is to backup the Wireless settings Configuration Template File It is to backup the settings as template file for editing Restore Default Settings System settings Backup and Restore Restore Configurations Upload Configuration File E Restore Restore Default Configurations Restore You can backup settings to a file and restore settings from that file You also can restore all settings back to default by selecting Restore Default
62. oute Destination network of the route Route Mask Subnet mask to apply on destination network Next Hop IP The next hop IP address to the specified network Interface The interface attached to this route VolP Wireless Router User s Manual 65 2 5 8 QoS Settings Advanced Settings QoS WAN QoS Enable WAN Qos Downstream Bandwidth Full Rate 62 kbps Upstream Bandwidth Full Rate Wles kops ToS IP Precedence Tos DiffServ Settings DiffServ DSCP ToS IP Precedence Signaling Precedence 3 Flash a Voice Data Precedence S CRITIC ECP Enable WAN QoS Check the box to guaranty the voice quality Voice packets have the highest priority in IP networks and the data transmission is distributed to less bandwidth Downstream Bandwidth Select the downstream bandwidth that is the same as the actual bandwidth subscribed from the drop down menu Upstream Bandwidth Select the upstream bandwidth that is the same as the actual bandwidth subscribed from the drop down menu ToS IP Precedence Select the precedence for signaling data and voice voice data DiffServ DSCP Select the number of signaling data and voice voice data values Note For the VoIP Router ToS IP Precedence and DiffServ are the same function You only select one for priority marking VolP Wireless Router User s Manual 66 2 5 9 DDNS Advanced Settings DDNS Enable Dynamic DNS D
63. outer should automatically sync up with time servers First NTP time server Select the desired domain name of a NTP server as first priority Second NTP time server Select the domain name of a NTP server as second priority Current Router Time lt shows the current time of the VolP Router Time Zone Select your time zone from the drop down menu Enable Daylight Saving To enable disable daylight saving time Daylight Saving Offset Set the current time zone offset for your location Daylight Saving Dates Set the start and end dates for daylight saving time 2 2 Language The system provides English Traditional Chinese and Simplified Chinese for displaying text on web pages Changing the language setting also changes the language for IVR Interactive Voice Response System settings Language Web UI IVR Language English VolP Wireless Router User s Manual ES 2 7 3 Login Account System settings Login Account Admin Administrator s Name admin Administrator s Password RT Confirm Password AAA Web UI Login ID User Web UI IVR Password MTTitiiittty Confirm Password PPP Note There are two operating levels when entering the Web Ul Logging in as the ADMIN allows you to change all settings A Web UI USER only has access to some settings Password It is highly recommended that you create a password to keep your VoIP Router secure System settings Login Account Port of Web Access fr
64. pically use dynamic assignment of IP Address The Host Name field is optional but may be required by some Internet General Settings WAN Enable Default Route L IP address Subnet mask Default Gateway IP MTU Domain Name Server Primary IP Domain Name Server Secondary IP Service Providers WAN Settings Enable VLAN Tagging VLAN ID Priority Type Static IP 255 255 255 0 192 168 1254 168 9511 Static IP Select this option if your ISP Internet Service Provider provides you a Static IP address Enter the IP address Subnet Mask and Default Gateway IP VolP Wireless Router User s Manual 16 General Settings WAN WAN Settings Enable VLAN Tagging VLAN ID Priority Enable Default Route a WAN 1 Settings PPPoE Account PPPoE Password esssssssss Confirm Password leseecceeee PPPoE Service Name Optional MTU 1992 WAN 1 Domain Name Server Manual Domain Name Server Primary IP 168 9511 O O Domain Name Server Secondary IP Po PPPoE Select this option if your ISP requires you to use a PPPoE Point to Point Protocol over Ethernet connection Enter the PPPoE Account PPPoE Password and re enter Password to confirm General Settings WAN WAN Settings Enable VLAN Tagging Enable peta Default Route El PPTP Server PPTP ID PPTP Password
65. r WDS connection Comment The space is reserved for comment or notation 2 4 6 Site Survey When wireless client mode is enabled click the Refresh button to display any Access Point on your wireless network so that a wireless client can obtain SSID BSSID Channel Type Encryption and Signal through scanning using this Site Survey tool Wireless Settings Site Survey SSID BSSID Type Encrypt Signal HomeLoAirStation O0 0d 0b bc 95 66 AP no 2 4 7 WPS Wireless Settings WPS Self PIN Number Change PIN 65503171 PIN Configuration Start PIN Push Button Configuration Start PBC It allows users establish wireless connect between VoIP Router and computers via WPS Wireless Protect Setup method VolP Wireless Router User s Manual 49 Example for setting Wireless profile via WPS method on Windows 7 Enter Network and Sharing Center Click Set up a new connection or network ue All Control Panel Items Network and Sharing Center Search Control Pa Control Panel Home i i View your basic network information and set up connections Manage wireless networks f A X amp P Change adapter settings ange adapter settings WINTE Internet Change advanced sharing This computer settings View your active networks You are currently not connected to any networks a Set up a new connection or network Set up a wireless broadband dial up ad hoc or VPN connection ors point Click Connect
66. rm Line Hot Line Delay Do Not Disturb Unconditional Forward Busy Forward No Answer Forward Call Hold Call Transfer Call Waiting Local Mixer Call Pickup Call Back on Busy Blind Transfer Enable Call Feature Code Check the box to enable the advanced function for Call Features such as Call Pickup Automatic Redial and Unattended transfer Calling Feature Instructions Call Hold The call will be held after the FLASH button is pressed on the phone set The VoIP Router will play music on hold provided by your ITSP or VSP to the remote end Call Transfer The call will be held after FLASH button is pressed on local phone set the VoIP Router plays on hold music to the remote end Meanwhile the local user can dial out another number after the dial tone is heard After the handset is on hooked the call originally on hold will then be transferred to the new number regardless the status of the new call If wrong number is dialed for the new call press the FLASH button will switch back to the call on hold Also if the local user doesn t hang up the phone after the new call is set up press the FLASH button will switch between the original call and the new call Please note that the PBX between phone sets and the VoIP Router must support FLASH features in order to use this function If a phone set is connecting directly to the F
67. rt User Name Password Enter the account information for accessing the server if needed Directory Enter the location of the firmware file 2 7 8 Logout If setting or parameter has been changed remember to save the changes before you logout the configuration menu Logout VolP Wireless Router User s Manual 79 3 Configuring the VolP Router through IVR Preparation 1 Connect the power supply telephone set telephone cable and network cable properly 2 Ifa static IP is provided confirm the correct IP settings of the WAN Port IP address Subnet Mask and Default gateway Please contact your local Internet Service Provider ISP if you have any question 3 If you intend to operate the VoIP Router under NAT the IP range of VolP Router WAN Port and LAN Port IP Address should not be the same in order to avoid phone failures IVR configuration provides basic query and setup functions while browser configuration provides full setup functions IVR Interactive Voice Response The VoIP Router provides convenient IVR functions Users are able to get query and setup the VoIP Router with a phone set and function codes without turning on the PC Note When finishing the setup make sure the new settings are saved This will enable the new settings to take effect after the system is restarted Instructions FXS Port Connect to telephones To access IVR mode passwords should be entered password Alphabets to
68. s Multiple AP Enable 802 11 Mode SSID O ngb ssID 1 LAN wWAN Y s LAN WAN w LAN WAN e METIO ngb 5sID 2 nab 5510 3 lt K nob lv s504 Multiple AP It is used for different level of clients Such as different departments or guests And you could assign different password for each SSID VolP Wireless Router User s Manual 42 2 4 2 Advanced Settings This section introduces advanced configuration for the wireless access point If you are not familiar with the following functions keep the default parameters In some cases incorrect settings may reduce wireless performance Wireless Settings Advanced Settings Fragmentation 256 2346 RTS Threshold 0 2347 RF Output Power Fragmentation A packet can be fragmented into small units to pass over a network medium that can not support the original packet size If you encounter a busy network a lower value of Fragment Threshold could improve performance If the traffic flows are not very busy a higher Fragment Threshold provides good network performance In most case keeping the default value 2346 is recommended RTS Threshold RTS Threshold is a mechanism to implement in collision avoidance In a large wireless network two stations do not hear each other but can hear wireless access point When the two send data to Access Point at the same time it may result in data collision and a loss of
69. ssage Header After From Before lt sip by default settings It will be located in SIP gt Message Header gt After lt sip Before if ticked INVITE With Remote Party ID Header Check the box to comprise the information of Remote Party ID in the message header of INVITE Different format of INVITE header might cause the call not to be connected Please consult with your VolP Service Provider before enabling it Callee Quick Media VolP Router will send RTP to remote party immediately as user answer an inbound call FXS Hunting For Unknown Number Select the response for an incoming call which the called number is not exist in on the VolP Router Disable VolP Router responses 404 not found Hunt and Transit Dial VolP Router sends alert to an available FXS port and dial the number to PBX as the FXS port picked up by PBX It works with SoftSwitch or IPPBX to allow a remote client reach the PBX extension for one step dial For virtual extension FXS Group Hunting Ring Type VoIP Router sends alert to an available FXS port for hunting group Enable SIP rport RFC 3581 ATA puts rport in SIP packets for SoftSwitch to deal well as ATA put under NAT Support URI Percent Encoding RFC 3986 Check the box to encode decode the letters of the basic Latin alphabet digits and a few special characters which follow RFC 3986 Call Hold Compatible With RFC 2543 It is used to set the procedure of Call Hold being compa
70. st Enforced Test Since the line test will interrupt a talking call that VoIP Router will ignore the in used line If you would like to test all the lines you select even it is in used please tick this item Test Click start to test ACO Clear alarm indication of the last test result VolP Wireless Router User s Manual 13 2 2 2 FXS Inward Self Test FXS Line Diagnostics gt Inward Self Test Line Enable Loopback Codec Loopback Analogue SLIC DC Power Voltage Tip Ring DC Feed Ringer 1 O an aie _ Enforced Test Ignore Port State It allows operator to verify if it is some problem on the FXS chip set Enable Select the lines you want to test Enforced Test Since the line test will interrupt a talking call that VolP Router will ignore the in used line If you would like to test all the lines you select even it is in used please tick this item Test Click start to test ACO Clear alarm indication of the last test result VolP Wireless Router User s Manual 14 2 3 General Settings 2 3 1 WAN WAN Wide Area Network Settings are used to connect to your ISP Internet Service Provider The WAN settings are provided to you by your ISP and oftentimes referred to as public settings Please select the appropriate option for your specific ISP IP Configuration Setting WAN Port There are four methods of obtaining a WAN port IP address DHCP which means a Dynamic IP Cable Modem Static IP PPP
71. t and send out with other numbers when dialing If you un check the box and is pressed after dialing it will speed up the phone number detection of the VolP Router Default Call Route Defines the default call route of the VoIP Router VoIP The call route is VoIP only Deny The call will be denied Default VoIP Route Profile Enter the Profile ID ranging from 1 10 for the Default VoIP routing Advanced Settings Digit Map Digit Map Testing Test Dial No Result Test Dial No You have to set some rules in Digit Map Setting first and enter the number for test Result The gateway will show the number for VoIP Dial out and PSTN Dial out according to the Digit Map Setting as below VolP Wireless Router User s Manual 56 Advanced Settings Digit Map Digitmap 1 20 Enable Scan Code VoIP Dialout User Dial Length Route VoIP Route Profile iT 3 7 e volp a e 2 O 7 7 a vaP v 1 E M wO YaF bd i 4 0O w S Dery ba hal 1 20 21 40 41 60 61 30 81 100 Scan Code Enter the digits for the VoIP Router to scan while user is dialing VolP Dial out Enter the actual dialing number rule for the VolP Router to call through the Internet User Dial Length Enter the total number of digits that user dialed Route Select VolP or Deny for this entry VoIP Route Profile Choose the proper Profile ID and click the VoIP Route Profile to set the priority of VolP Route Profile VolP Router Profile
72. ter Dz FXS Representative Po eee eee eee Number KO AAA ROA j i Loe IN FXS 0912345678 No Group 0912345678 q _ CO ae No Group Y 0922345678 a CEL Number Enter the number text or number and text in this field It is the Caller ID for the called party when you make a VolP call If you register the VolP Router to a SIP proxy server then it should be the number that provided by SIP proxy server Number and User ID Account are usually the same from most SIP proxy severs Each line has a number And the number of each line is not reiteration Hunt Group Port It allows operators to assign multi lines for a hunting group Register Check the box to register with SIP proxy server Invite with ID Account Check the box to call through SIP proxy server without registration It is always ticked when Register is also ticked Most VolP Service Providers will interdict the connection without registration User ID Account User ID Account are usually the same as Number from most SIP proxy severs Password Enter password and re enter to confirm VolP Wireless Router User s Manual 22 General Settings SIP SIP Proxy Server Proxy Server IP Domain 192 168 100 100 Proxy Server Port 5060 1 65535 Proxy Server Realm TTL Registration interval 600 10 7200s SIP Domain C Use Domain to Register Bind Proxy Inter
73. tible with RFC 2543 Enable SIP Allow Header It is used to put Allow in SIP packets The Allow header field lists the SIP requests supported by ITA when ticked Enable SDP ptime Attribute It is used to put ptime in SDP packets when ticked Use Redirect URI As To Header Receiving 3XX It is used to change the content of To header field when receiving 3XX Respond BUSY HERE while no line available for hunting It is used to reply BUSY HERE to the calling party while no line is available for hunting VolP Wireless Router User s Manual 29 2 3 5 Caller ID General Settings Caller ID FXS Caller ID Generation Send Caller 1D After The First Ring FSK Caller ID Type Belicore e FXS Caller ID Generation DTMF Sending Caller ID in DIMF signaling FSK Sending Caller ID in FSK signaling FSK Typell Send Caller ID in FSK signaling As the phone set supports Call Waiting Caller ID that FXS will send third party s number Send Caller ID After the First Ring Un Ticked FXS sends Caller ID before the first ring Usually it is used in DTMF mode Ticked FXS sends Caller ID between the first and second ring Usually it is used in FSK mode FSK Caller ID Type Either Bellcore ETSI or NTT could be selected VolP Wireless Router User s Manual 30 2 3 6 Hot Line General Settings Hot Line Warm Line Line Enable Type HotLine Hot Line No Hot Line De
74. tings Provision Settings Enable Auto Provisioning Provision Provision Server Address Port 10101 1 65535 Packet Format Proprietary Connect Provision Server During Start Up Connect Provision Server Periodically Auto Provision Interval 10800 60 604800 s Random Offset so 0 1800 s Provision Retry Times 10 O always 1 99 Retry Interval 30 30 1205 C Suspend Call Service TFTP Source Port E 1 65535 C Binding Server for Trigger Enable Auto Provisioning Check the box to start provisioning Provision Server Address Enter the Provisioning Server s IP address or URL required by your VoIP Service Provider Port Enter the Provisioning Server s listening port Packet Format Use the drop down menu to choose the packet transmitting format required by your VoIP Service Provider Connect Provision Server During Start Up Check the box to connect to Provisioning Server when the VolP Router is powered on or rebooted Connect Provision Server Periodically Check the box to connect to Provisioning Server periodically VolP Wireless Router User s Manual 62 Auto Provision Interval Enter the time for auto provisioning Random Offset Enter the offset of the time for auto provisioning Provision Retry Times Enter the retry time if a provisioning attempt fails Retry Interval Enter the interval for retrying Suspend Service Check the box to stop Vo
75. tion Sensitivity To set higher value to make VolP Router to be more sensitive VolP Wireless Router User s Manual 35 General Settings FAX Fax T 38 High Speed Redundancy Low Speed Redundancy FAA Max Rate High Speed Packet Time FAX Codec 6 711 udaw 64kbps v T 30 Bypass Payload Type 96 96 127 FAX Jitter Buffer 200 60 1200 ms High Speed Redundancy Set redundancy packets for FAX image It could repair FAX image for non continuous packets lost The higher redundancy the higher bandwidth required Low Speed Redundancy Set redundancy packets for FAX handshaking signaling FAX Codec Select G 711 a law G 711 u law or G 726 for T 30 from the drop down menu T 30 Bypass Payload Type Fill correct payload type of T 30 bypass method FAX Jitter Buffer Enter the buffer or jitter when receiving packets Note When you send a fax over an IP network the IP network needs to support fax over IP functionality either T 38 or T 30 Please consult your VoIP Service Provider for this setting Function Receive re INVITE with T 38 Disable Accept and change RTP to 1 38 1 38 Fax Accept and change RTP to 1 38 T 30 Fax Accept and change RTP to T 38 oie Accept and change RTP to 1 38 T 30 Only Accept and change RIP to T 38 T 38 Native Accept and change RTP to 1 38 T 30 V 152 Accept and change RTP to 1 38 VolP Wireless Router User s Manual 36 2 3 9 Calling Features General Settings Calling Features
76. to the Internet B Y Set Up a Connection or Network Choose a connection option Connect to the Internet Set up a wireless broadband or dial up connection to the Internet o Set up a new network Configure a new router or access point AL Manually connect to a wireless network ag Connect to a hidden network or create a new wireless profile VolP Wireless Router User s Manual 50 Click Wireless How do you want to connect Y Wireless 5 Ee tg ae oh Connect using a wireless router or a wireless network _ Broadband PPPoE Connect using DSL or cable that requires a user name and password Select a Wireless AP You are currently not connected to any networks Change your networking settings al Set up a new connection or network Not connected Set up a wireless broadband dial up ad hoc or VPN connection ee point afl Connections are available Connect to a network Wireless Network Connection Connect or reconnect to a wireless wired dial up or VPN network Choose homegroup and sharing options Access files and printers located on other network computers or chi Troubleshoot problems Diagnose and repair network problems or get troubleshooting infia Open Network and Sharing Center VolP Wireless Router User s Manual 51 Click OK to start setup i Y Connect to a network Connect or reconnect to a wireless wired dial up or VPN network connection
77. un check it to configure as all calls go through the Internet Invite URL need user phone Check the box to add user phone as a hint that the part left to the sign is actually a phone number Reliability of Provisional Responses Check the box to send a PRACK request during the progress of the request processing Reliability of Provisional Responses is to ACK at every SIP packet With this method SIP packet will act like TCP i e every packet sent will receive an ACK to make sure that packet sent has been received by other peer Compact Form Check the box to represent common header field names in an abbreviated form This may be useful when SIP message is too large to be carried on and recognized by the user agent VolP Wireless Router User s Manual 28 SIP Caller ID Obtaining Select the part of the SIP packet from the VoIP Router to obtain Caller ID There are several places where the Caller ID is located Remote Party ID Display Name It is located at SIP Remote Party ID Before lt sip Remote Party ID User Name It is located at SIP Remote Party ID After lt sip Before From Header Display Name The standard way is in SIP Message Header gt From gt SIP Display info From Header User Name lt locates at SIP gt Message Header gt From gt SIP from address before 0 Put Caller ID In URI This feature is to put Caller ID in URL The Caller ID is located in SIP gt Me
78. val for NAT D 18005 Initial Unregister C Unregister All Contacts C Keep SIP Auth C Support Message Waiting Indication MWI MWI Subscribe Interval 7200 0 disable 60 86400s Proxy Server IP Domain Enter the IP address or URL Uniform Resource Locator of SIP proxy server or soft switch Proxy Server Port Enter the SIP proxy server s listening port for the SIP in this field Leave this field to the default if your VoIP Service Provider did not give you a server port number for SIP Proxy Server Realm Enter the realm for SIP proxy server It is used for authentication in a SIP server In most cases the VoIP Router can automatically detect your SIP server realm So you can leave this option blank However if your SIP server requires you to use a specific realm you can manually enter it in TTL Registration interval 10 7200 s The interval for VoIP Router re report to SoftSwitch SIP Domain Enter the SIP domain provided by your VoIP Service Provider Note some SIP proxy servers might not require this If you enable Uses Domain to Register the VoIP Router will register to the SIP proxy server with the domain name you filled in Otherwise the VoIP Router will register to a SIP proxy server with the IP it resolves Use Domain to Register Check the box to use Domain to register with SIP proxy server The VoIP Router is registered to the SIP proxy server with IP address if un ticked Note Proxy Server R

VoIP Fiber Optical Router User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents