RIGEL 5RIGEL 5 - EasyGates Manuals & Guides
Contents
1. 60 eee 3 Closing delay time for leaf 2 Set the closing delay time for motor 2 which can be adjusted from 0 to t 60 seconds Set the slow down to approach time from 0 to 20 seconds The slow down SLou time is subtracted from the work time 0 sec 20 sec Slow down time NOTE it is advised to activate timing doun E NOTE only use this function when limit switches are fitted NOTE Do not use with hydraulic motors ER E sec 15 Traffic light area clearance Set the required clearance time for the area involved in the traffic governed i time by traffic light from 0 to 30 seconds Set to 0 if not used Set the percentage value of the current from 0 deactivated pre heating to GER P EERE 0 99 30 Preheating 99 which can be made to pass through the motor windings to keep them at the right temperature NOTE Only with SSR5 H H o Seen 1 99 50 Slowdown Motor Torque Set numerically from 1 to 99 the value of motor torque during slowdown tor Wu time Set the numerical torque value from 1 to 99 Ear FW 1 99 50 Motor torque NOTE When using with oil hydraulic motors it is necessary to set the torque value to 99 and adjust the force directly on the motor Set the braking value from 096 min to 9996 max according to the gate Set the value of the emergency braking from 096 min to 9996 max This brRHE 0 9996 6096 Emergency braking is carri2. INSTALLATION MANUAL In case of obscuring this excludes photocell operation on opening Phatc Photocells on During the closing phase it immediately reverses the motion aPEn opening In case of obscuring the photocells are active both on opening and on closing When a photocell is obscured on closing it reverses the motion only after the photocell is disengaged ON Closes the gate after photocell disengagement before waiting for the end of the TCA automatic closing time a Rapid closing set OFF not entered ON Activates photocell check see Fig D ese Phot OFF Photocelltest OFF Deactivates photocell check ese on Electric edge ON Activates electric edge check see Fig D test Deactivates electric edge check EE Photocell test ON Enables the test of the active photocells on opening oF on opening Desables the test of the active photocells on opening EESE Prot oe Photocell test EUM Enables the test of the active photocells on closing cL on closing Desables the test of the active photocells on closing DRSEEF ore Master Slave Se The control panel is set as Master in centralised connection see SCS OPTIONAL MODULES OFF The control panel is set as Slave a centralised connection see SCS OPTIONAL MODULES FINES ON The receiver is configured for operation in fixed code mode Fixed code i OFF The receiver is configured for operation in
3. ELEc electromechanical operator wmddomg La or or Photocell test Electicedgetest_ Por or orr orr rr er er er er or or or or or or OFF Recio vransmier programming ov ow f on or OFF hydraulic OFF OFF OFF Time count electromechanical Light Alarm orr ore oF automatic operation residential iActivemotor Sojle Sr semiautomatic operation residential Safety edge ow on on on on Blinking output or or orr ore Ac automatic operation commercial 5c semiautomatic operation commercial ind dead man operation FLT BAR PHOT CL a AR oa Un A w N ul Na NA Ui A w N A w NA UW A wi
4. Gate open warning light Blinker Fuses 4 TERMINAL BOARD WIRING Fig A Once suitable electric cables have been run through the raceways and the automated device s various components have been fastened at the prede termined points the next step is to connect them as directed and illustrated in the diagrams contained in the relevant instruction manuals Connect the live neutral and earth wire compulsory The mains cable must be clamped intherelevantcable gland andthe accessories wires in the cable gland while the earth wire with the yellow green coloured sheath must be connected in the relevant terminal 20 RIGEL 5 DESCRIPTION GND terminal 23 230V 10 50 60Hz power supply 2 neutral 3 phase E Motor connection 1 delayed opening terminals 5 6for motor drive terminal 4 common Motor capacitor connection 1 Motor connection 2 delayed closing terminals 8 9 for motor drive terminal 7 common N B If only one motoris used use motor output 2 and configure logic 1 active motor Motor capacitor connection 2 230V output for blinker light 40W max and 230V mo delelectric lock WARNING If the SSR5 auxiliary board is used for motor preheating move the connection to terminals 12 13 Fig A and refer to LOGIC TABLE B Blinker output 230V output for zone lighting courtesy light dipswitch ON flashing light output dipswitch OFF 230V output for courtesy light courtesy light dipswitch OFF
5. gt 5 LIMIT SWITCH 1 activation of input for MOTOR 2 CLOSING LIMIT _ Uc SWITCH ET Nini dn nunes activation of input for MOTOR 2 OPENING GE ET radio control devices memorised ck somal check photocell connection and or rEPaEES ok gt 00 S P y parameter logic settings e 2 safety edge test anomaly check safety edge connection and or 7 parameter logic settings 03 photocell on opening test anomaly check photocell connection and or parameter logic settings Er OY photocell on closing test anomaly check photocell connection and or parameter logic settings hardware anomaly check connections to motor H 0 1 9 A B C D E F 18 RIGEL 5 D811472 00100 01 100 01 GENERAL WARNINGS S WARNING Important safety instructions Carefully read and comply with the Warnings booklet and Instruction booklet that come with the product as incorrect installation can cause injury to people and animals and damage to property They contain important information regarding safety installation use and maintenance Keep hold of instructions so that you can attach them to the technical file and keep them handy for future reference D8114 1 GENERAL SAFETY WARNING An incorrect installation
6. logic OFF Enables 4 step logic when the 3 steplogicissetto OFF sd 2step 3step 4step 79 Enables 3 step logic with 2 steps OFF E OFF Disables 3 step logic ib Ma ads Logic c ON OFF ON OFF ON OFF ON OFF N Ram blow on opening Ram blow in ON closing DEER 3 SEEP ON The blinker comes on about 3 seconds before the motor open me PrE RLREn Pre alarm ST k h h stop TCA stop TCA OFF Die inker comes at the same time as the motor after stopping If the motors remain still in a totally open or closed position for over one hour they are activated for about 3 seconds in the respective direction This operation takes place once every hour N B This function has the purpose of compensating any volume decrease the hydraulic motors due to ON drop during prolonged fori ight or to internal leak Di Lock hold a temperature drop during prolonged pauses for instance at night or to internal leaks 5 1 IMPORTANT When no adequate mechanical backstops are installed do not use this function It is also be absolutely avoided in the automation of sliding gates Exclude block maintenance sto ON Hold to run operation the manoeuvre continues as long as the command key is kept pressed 9 IMPORTANT It is not possible to use the radio transmitter OFF Impulse operation 22 RIGEL 5 D811472 00100 01 0811472 00100 01
7. 1 ate See PARAMETERS MENU 1 T gt AE mS See LOGIC MENU zi ex gt Cer oc 2 Add h iddEn Hitten A ex D FELERSE dS button Ga mm u 7 h iddEn NH SS gt FELERSE ES irEd tte Cen mm 4 4 Prt E Age gt o 9 222088 0 o gt Ea gt o mE 5 515 eg EHWBURBE ox y Let EPI DIAGNOSTICS and WARNINGS FER ex DIAGNOSTICS Ce CODE 5trE EXTERNAL START input activation ox Se Str i INTERNAL START input activation EnD DESCRIPTION 4 ox PEd input activation PEDESTRIAN oPEn OPEN input activation BS gt e cL5 CLOSE input activation ESP StoP STOP input activation Y Phot PHOTinputactivation oo BEFRUEE ox 229 PhoP activation ofinput for PHOTOCELL ON OPENING Phet activation of input for PHOTOCELL ON CLOSING inputactivation SAFETY EDGE 2 Guel activation of input for MOTOR 1 CLOSING LIMIT SA SWITCH Control unit software version Suo activation of input for MOTOR 1 OPENING ox
8. N 10 RIGEL 5 A w N TEST PHOT OFF TEST BAR OFF TEST BAR ON AU NA UU NA Bu NA WM A wi N Uj A w N TEST PHOT CLOSE OFF TEST PHOT CLOSE ON D811472 00100 01 0811472 00100 01 Combinazioni possibili Not poss
9. closing resetting the strian open pedestrian position OFF acts on both motors Light Alarm EUM Gate open alarm output activated if the gate remains open for twice the TCA time set 9 Stair light control the impulse stays on for 1 second Dat CS Only motor 2 activated 1 leaf oc an Both motors are activated 2 leaves Gate openor2nd The output between terminals 18 and 19 is configured as Gate open warning light in this case the 2nd radio ScA ech radio E D channel controls pedestrian opening warning light OFF The output between terminals 18 and 19 is configured as 2nd radio channel dE a nput of terminals 36 37 is active as input for the safety edge or fi Input of terminals 36 37 is active as input for opening photocells Setthe output at terminals 12 13 courtesy light as blinking output active only during leaf movement N B ON a SC ds Any setting relating to the courtesy light function is ignored Lei Blinking ou Keep the output at terminals 12 13 as courtesy light or zone light tput WARNING It is not possible to use the SSR5 board in motor preheating mode and at the same time have the Zone light Courtesy Light and Blinker Electric lock on In this case outputs 10 11 cannot be used and outputs 12 13 can only be used for one of the two functions ion qus Type of lock ON Suction type lock Enabled with gate closed OFF
10. flashing light output dipswitch OFF 230V output for flashing light output flashing light dipswitch ON Stair light output N O dip Light alarm OFF Only connect theseterminals to safety extra low voltage SELV circuits suitably insulated from live parts Light alarm output N O dip Light alarm ON Only connect theseterminalsto safety extra low voltage SELV circuits suitably insulated from live parts N O output for 2nd radio channel SCA dipswitch 2ch OFF N O output for gate open warning light This warning light is off when the gate is closed flashes as it is closing and remains on when the gate is open or opening dipswitch SCA 2ch ON 24V output 1A max to power accessories 24V output to power VSAFE 12V solenoid latch output lock type dipswitch OFF 12 solenoid sucker output lock type dipswitch ON Antenna input for radio receiver board 24 signal 25 braid INTERNAL START Pushbutton N O Internal Start command for traffic light START Pushbutton N O Parallel to radio receiver relay 1 External Start command for traffic light PEDESTRIAN pushbutton N O Activation takes place on motor 2 moreover if the opening cycle has started not from pedestrian pushbutton the pedestrian control has the same effect as a Start command OPEN Pushbutton N O CLOSE Pushbutton N O LOCK pushbutton N C If not used leave the jump
11. rolling code mode This enables transmitter storage via radio 1 First press the hidden key P1 and then the normal key T1 T2 T3 or T4 of a transmitter already memorised in standard mode by means of the radio menu 2 Within 10s press the hidden key P1 and the normal key T1 T2 T3 or T4 of a transmitter to be memorised Radio transmit The receiver exits the programming mode after 10s other new transmitters can be entered before the end ter program of this time ming This mode does not require access to the control panel This disables transmitter storage via radio The transmitters can only be memorised using the appropriate Radio menu Clones and replays are not accepted The control unit calculates the activation time of each motor based on the preceding manoeuvres Time count opp The control unit activates the motors at each manoeuvre for the time set Always set the operation time to a slightly higher value than needed to carry out the complete manoeuvre Zone ON Zone light Remains active as long as the manoeuvre lasts L Courtesy light Courtesy light Remains active for 90 seconds after last operation N B These settings cannot be used if the blinker output is set to ON Input for the connection of an external timer Clock Bad The Clock input is only active in Motor 2 for the pedestrian time set clocH PEd oc ede A start command given during the clock phase carries out complete gate opening and
12. Click lock Enabled with a pulse at each opening 10 3 TABLE C RADIO MENU rd io Logic Description Add Start Key Add associates the desired key with the Start command Add 2ch Key Add ech associates the desired key with the 2nd radio channel command WARNING Erases all memorized remote controls from the receiver s memory EB Displays receiver code required for cloning remote controls ON Enables remote programming of cards via a previously memorized W LINK transmitter It remains enabled for 3 minutes from the time the W LINK remote control is last pressed OFF W LINK programming disabled RIGEL 5 23
13. NNECTION USING SCS1 BOARD Fig A E The RIGEL 5 control panel allows several automation units SCS1 to be connected in a centralised way by means of appropriate serial inputs and outputs This makes it possible to use one single command to open and close all the automation units connected Following the diagram in Fig E proceed to connecting all the RIGEL 5 control panels exclusively using a telephone type line Should a telephone cable with more than one pair be needed it is indispen sable to use wires from the same pair The length of the telephone cable between one appliance and the next must not exceed 250 m At this point each of the RIGEL 5 control panels must be appropriately configured by setting a MASTER unit first of all which will have control over all the others to be necessarily set as SLAVE see logic menu Also set the Zone number see parameter menu between 0 and 127 The zone number allows you to create groups of automation units each one answering to the Zone Master unit Each zone can only be assigned one Master unit the Master unit in zone 0 also controls the Slave units in the other zones 8 2 Interface with WIEGAND systems via SCS WIE module Refer to the SCS WIE modules instructions 9 SSR5 TRAFFIC LIGHT MOTOR PREHEATING BOARD When inserted in the appropriate connector it provides Control of two traffic lights with 2 lights each Preheating of motors for cold climate Refer to specific man
14. RI CENTRALINA UNIVERSALE PER IL CONTROLLO DI UNO O DUE MOTORI UNIVERSAL CONTROL UNIT FOR OPERATING ONE OR TWO MOTORS UNITE DE COMMANDE UNIVERSELLE POUR LE CONTROLE D UN OU DEUX MOTEURS UNIVERSALSTEUERUNG F R EINEN ODER ZWEI MOTOREN CENTRAL UNIVERSAL PARA EL CONTROL DE UNO O DOS MOTORES CENTRAL UNIVERSAL PARA O CONTROLO DE UM OU DOIS MOTORES D811472 00100_01 29 10 09 STRUZIONI D USO E DI INSTALLAZIONE NSTALLATION AND USER S MANUAL NSTRUCTIONS D UTILISATION ET D INSTALLATION NSTALLATIONS UND GEBRAUCHSANLEITUNG NSTRUCCIONES DE USO Y DE INSTALACION NSTALLATIEVOORSCHRIFTEN AZIENDA CON SISTEMA DI GESTIONE ER Reacy me Bes UNI EN ISO 14001 2004 Attenzione Leggere attentamente le Avvertenze all interno Caution Read Warnings inside carefully Attention Veuillez lire attentivement les Avertissements qui se trouvent l int rieur Achtung Bitte lesen Sie aufmerksam die Hinweise im Inneren jAtenci n Leer atentamente las Advertencias en el interior Let op Lees de Waarschuwingen aan de binnenkant zorgvuldig 0811472 00100 01 SSR5 Fig F F2 p mA T 2 630 mA T 110 Connettore programmatore palmare Palmtop program
15. dance with the provisions of the regulations in force CHECKING THE AUTOMATED DEVICE Before the automated device is finally put into operation perform the fol lowing checks meticulously Make sure all components are fastened securely Check the correct functioning of all safety devices limit microswitches photocells sensitive edges etc Make sure that the anti crush system stops the door within the limits provided for by the standards in force Check the emergency operation control device Check the opening and closing operations with the control devices in use Check the standard and customised electronic functioning logic MAINTENANCE Dismantle the gearmotor and replace the lubricating grease every two years When any operational malfunction is found and not resolved discon nect the mains power supply and request the assistance of a specialised technician installer SCRAPPING Materials must be disposed of in conformity with the current regulations In case of scrapping the automation devices do not entail any particular risks or danger In case of recovered materials these should be sorted out by type electrical components copper aluminium plastic etc DISMANTLING Whenthe automation system is disassembled to be reassembled on another site proceed as follows Disconnect the power supply and the entire electrical installation Remove the actuator from its fixing base Disassemble all the installation compo
16. del receptor de radio A e lE 4 Connector Radio ontvanger O Meg 05 K4 esoe 00 14 15 16 17 18 19 20 21 22 23 24 25 12 3 415167 819 10 11112 13 14 15 16 17 18 19 20 21 22 23 24 25 44 45 46 47 48 49 50 z z N L 8 8 1 M1 M2 NA NO Se 5 11 1213 11 12 13 5 ANT Lock 29 12 18 19 20 21 Ze 5 y 05 DA 27 2 2 40W max 40W max ee gt g p Dip LANPEGG OFF Dip LANPEGE ON fV oN 5 8 Dip bL nH OFF Dip bL nH ON gt gt DipFEU ec OFF DipFEU ON Dip nH OFF Dip bL nH ON Il CH Dip LUZ InE OFF Dip LU InE ON PHOT FAULT PHOT CL Collegamento di 1 coppia di fotocellule non PHOT CL FAULT BAR PHOT OP FAULT verificate Connection of 1 pair of non tested photocells Connexion 1 paire photocellules non v rifi es Anschluss von einem Paar nicht berpr ften Fotozellen Conexi n de 1 par fotoc lulas no comprobadas Aansluiting van 1 paar fotocellen anders dan trust
17. ed device gt gt gt 8 88 36 37 LOGICA test fotocellule OFF Photocell test LOGIC OFF LOGIQUE essai photocellules D sactiv e LOGIK Test Fotozellen OFF LOGICA prueba fotoc lulas OFF LOGICA test fotocellen OFF RIGEL5 3 HISLNAG 5119 3 ONVITVLI TONVWdS4 m m Ke E SYSTEM SETTINGS MENU LEGENDA reser se Re Se tna Scroll up 0 Scroll down Confirm Switch on display EE time motor 2 20 20 20 20 20 Pedestrian operationtime 6 6 6 6 ERARE 2 2 Opening time for leaf 1 Exit Menu oo Slow down time lectromechanical Traffic area clearance time Preheating sd Slowdown motor torque hydraulic Motor torque electromechanical 50 50 50 Brains ejo ojo o Emergency braking Las co o e om ow or Fopeningimpulelock OFF OFF ov oorr ov oe or Pela ov or or ow ov Lock hold hdr hydraulic operator lectromechanical Hold to run
18. ed out by enabling the safety commands on the inputs 34 block 37 SAFE OP and 55 SAFE CL Senf 127 Enter the zone number between 0 minimum value 127 maximum value See paragraph SCS OPTIONAL MODULES 10 2 TABLE B LOGIC MENU Lat ic Cross out setting Description used Automatic Switches automatic closing on Closing Time i i i Opening Impul se lock Switches automatic closing off The Start impulse becomes effective during the opening phase TCA The Start impulse becomes effective during the TCA dwell period closing The start impulse is effective during the closing stage It pushes for approx 2 seconds in closing direction before opening This allows the electric lock to be released more easily not affected by limit switches IMPORTANT When no adequate mechanical backstops are installed do not use this function It is also to be absolutely avoided in the automation of sliding gates OFF Excludes the ram blow in closing Before carrying out the closing manoeuvre the gate pushes for about 2 seconds on opening This allows the electric lock to be released more easily not affected by limit switches IMPORTANT When no adequate mechanical backstops are installed do not use this function It is also to be absolutely avoided in the automation of sliding gates OFF Excludes the ram blow in closing 2 step 4 step ON Enables 2 step logic prevails over 3 step logic Astart impulse has the following effects
19. er con nected Photocell contact input PHOT n c If not used leave jumpers inserted Photocell contact input PHOT OPENING N C Ifnot used leave jumpers inserted dipswitch BAR OFF BAR safety edge input n c If intervenes during opening it stops and we have partial closure If not used leave jumpers inserted dipswitch BAR ON Opening limit switch for motor 1 SWO1 N C If not used leave the jumper connected Closing limit switch for motor 1 SWC1 If not used leave 20 44 24 25 26 27 27 28 36 37 the jumper connected Opening limit switch for motor 2 SWO2 n c If not used leave the jumper connected Closing limit switch for motor 2 SWC2 n c If not used leave the jumper connected 20 44 24V output for transmitters 45 46 47 Connection with tested safety devices see Fig D 48 49 50 Connection with tested safety devices see Fig D D811472 00100 01 0811472 00100 01 INSTALLATION MANUAL Clock input N O If the connected contact is open N O the leaves close and get ready for normal operation If the contact is closed the leaves open and stay open until the contact reopens If the opening movement controlled by the TIMER is prevented by the safety devices gate opening can be resumed by activating the START OPEN control Input for photocelledge contact on closing SAFE CL N C In case of activation during closing the gate is st
20. f at least 0 75 mm Have an omnipolar circuit breaker installed with a contact separation of at least 3 mm and featuring overload protection suitable for cutting the automated device off from the mains Only use pushbuttons with a capacity of 10A 250V or more The cables must be held in position using an extra fixing device in the proximity of the terminals e g with cable clamps Alsoadd moreclipsto the limit device wires to the transformer primary or secondary wires and to the wires connected to the printed circuit During installation the power supply cable must be stripped in order for the earthing wire to be connected to the appropriate terminal but the active wires must be left as short as possible The earthing wire must be the last to stretch in the case where the cable fixing device becomes loose WARNING extremely low safety voltage cables must be phisically separated from low voltage cables Access tothe electrical compart ment or to limit switches must be allowed to skilled personnel only Setting sensitivity incorrectly can resultin damageto property and injury to people and animals Compliance with current safety rules with regard to people animals and property must be assured at all times and more specifically measures must be taken to avoid risks of injury due to crushing in the area where the pinion and rack mesh and any other mechanical hazards All critical points must be protected by safety devices in accor
21. g Clock input Connector for traffic light board motor preheating Incorporated radio receiver The boardis provided with a removable terminal board for easier maintenance and replacement This is supplied with a series of prewired jumpers to make work easy for the installer The jumpers relate to the following terminals 33 34 35 36 36 37 38 39 39 40 41 42 42 43 52 55 If the above terminals are used remove the respective jumpers 2 TECHNICAL SPECIFICATIONS CONTROL UNIT Power supply 230V 10 50Hz Mains low voltage insulation gt 2MOhm BOOM mains bty 3750V for 1 minute 1A 1A max 230V 2A 2A max 110V max 150W 24V 1A max absorption 12V 0 5A max 2A for 3 s max 3A 250V Dimensions po 2nd ch relay 2nd ch for 1 sec Built in Rolling Code radio re frequency 433 92MHz ceiver 4 billion Max n of remotes that can 63 memorized 50 Ohm 8058 Special supply voltages to order Usable transmitter versions ra AIIROLLING CODE transmitters compatible with c Ready 3 TUBE ARRANGEMENT Fig A Install the electrical system referring to the standards in force for electrical systems 64 8 IEC 364 harmonization document HD 384 and other national standards Dielectric strength Motor output current Motor relay commutation current Zone courtesy light Supply to accessories Electric lock Light alarm output with free n o contact
22. ible combinations Combinaisons non possibiles Nicht mogliche kombinationen Combinaciones no posibles Combinaties niet mogelijk Fotocellule Photocells Coste Fotocellule in Apertura Coste Fotocellule in Apertura Coste Fotocellule in Chiusura Fotocellule in Chiusura Fo Photocellules Fotozellen Fotocellule in Apertura Coste Fotocellule in Apertura Coste Fotocel tocellule in Chiusura Fotocellule in Chiusura Foto Fotocellulas Fotocellen lule in Apertura Coste Fotocellule in Apertura cellule in Chiusura Fotocellule in Chiusura gt gt gt gt WININ l gt Ww gt gt gt RIK A gt gt gt gt gt p gt s 1 250 J Programmatore palmare universale Universal palmtop programmer Programmateur de poche universel Universellen Palmtop Programmierre Programador de bolsillo universal Programmeerbare Universele Palmtop RIGEL 5 11 ACCESS MENUS Fig 1 LEGENDA Scroll up 4 Scroll down OK Confirm Switch on display eg 0 re Exit Men PAAR
23. mer connector Connecteur programmateur de poche Steckverbinder Palmtop Programmierer Conector del programador de bolsillo Connector programmeerbare palmtop Display tasti programmazione Display 4 programming keys 51 52 FFT 44 45 46 47 48 49 50 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 TP ei Afficheur touches programmation Display Programmierungstasten Pantalla botones programaci n Display programmeringstoetsen Connettore scheda opzionale Optional board connector Connecteur carte facultative Steckverbinder Zusatzkarte 6 3 A F 230V 10 A F 110V FFT 4 6 7 8 810111213 5P RIGEL 5 RAHAKI Conector de la tarjeta opcional S 3 E rnm Connector optionele kaart a 2 Q i Xx HH T e o 6 Connettore ricevitore radio i Radio receiver connector Connecteur R cepteur Radio Stecker Funkempf nger iE Conector
24. nents In the case where some of the components cannot be removed or are damaged they must be replaced Correct controller operation is only ensured when the data contained in the present manualare observed The Companyis notto be held respon sible for any damage resulting from failure to observe the installation standards and the instructions contained in the present manual The descriptions and illustrations contained in the present manual are not binding The Company reserves the right to make any alterations deemed appropriate for the technical manufacturing and commercial improvement of the product while leaving the essential product fea tures unchanged at any time and without undertaking to update the present publication RIGEL 5 19 HSI1ON3 INSTALLATION MANUAL 1 FOREWORD The RIGEL 5 control unit is supplied by the manufacturer with standard setting Any modifications must be entered using the universal palmtop programmer or the incorporated display This Control unit supports the entire EELINK protocol These are its main features Control of one or two motors up to 600W power Electronic torque setting Adjustable electrodynamic braking End of run speed slow down Separate opening closing limit switch inputs for each motor Output for zone light Separate inputs for safety devices 12V output for click or suction type electric lock Output for timer pilotin
25. opped and partly reopened If not used leave the jumper connected 5 CONNECTION WITH EXPANSION BOARDS AND UNIVERSAL HANDHELD PROGRAMMER Fig A Refer to specific manual 53 5 Jm Jm 6 SAFETY DEVICES NOTE ONLY USE RECEIVING SAFETY DEVICES WITH FREE CHANGEO VER CONTACT 6 1 TESTED DEVICES FIG D 6 2 NON TESTED DEVICES FIG C D 7 CALLING UP MENUS FIG 1 7 1 PARAMETERS MENU Hr PARAMETERS TABLE A 7 2 LOGIC MENU L o ic LOGIC TABLE B 7 3 RADIO MENU rd io RADIO TABLE C IMPORTANT NOTE THE FIRST TRANSMITTER MEMORIZED MUST BE IDENTIFIED BY ATTACHING THE KEY LABEL MASTER In the event of manual programming the first transmitter assigns the RE CEIVER S KEY CODE this code is required to subsequently clone the radio transmitters The Clonix built in on board receiver also has a number of important ad vanced features Cloning of master transmitter rolling code or fixed code Cloning to replace transmitters already entered in receiver Transmitter database management e Receiver community management Tousethese advanced features refer to the universal handheld programmer s instructions and to the general receiver programming guide 7 4 LANGUAGE MENU LAnGUAGE Used to set the programmer s language on the display 7 5 DEFAULT MENU Restores the controller s DEFAULT factory settings 8 SCS OPTIONAL MODULES 8 1 SERIAL CO
26. or improper use of the product can cause damage to persons animals or things The units making up the machine and its installation must meet the requirements of the following European Directives 2004 108 EEC 2006 95 EEC and later amendments For all countries outside the EEC itis advisable tocomply with the above mentioned standards in addition to any national standards in force to achieve a good level of safety The Firm disclaims all responsibility resulting from improper use or any use other than that for which the product has been designed as indica ted herein as well as for failure to apply Good Practice in the construc tion of entry systems doors gates etc and for deformation that could occur during use Make sure the stated temperature range is compatible with the site in which the automated system is due to be installed Do not install the product in an explosive atmosphere Disconnect the electricity supply before performing any work on the sy stem Also disconnect buffer batteries if any are connected Have the automated system s mains power supply fitted with a switch or omnipolar thermal magnetic circuit breaker with a contact separation of at least 3 5 mm Make sure that upline from the mains power supply there is a residual current circuit breaker that trips at 0 03A Make sure the earth system has been installed correctly earth all the me tal parts belonging to the entry system doors gates etc and all par
27. ts of the system featuring an earth terminal Installation must be carried out using safety devices and controls that meet standard EN 12978 Apply all safety devices photocells safety edges etc required to keep the area free of crushing dragging and shearing hazards Only use original spare parts for any maintenance or repair work The Firm disclaims all responsibility for the correct operation and safety of the automated system if parts from other manufacturers are used Do not make any modifications to the automated system s components unless explicitly authorized by the Firm Dispose of packaging materials plastic cardboard polystyrene etc in accordance with the provisions of the laws in force Keep nylon bags and polystyrene out of reach of children Anything which is not expressly provided for in the present instructions is not allowed The device is not meant to be used by people including children whose physical sensory or mental capacities are impaired or who do not have suitable experience or knowledge unless a person responsible for their safety provides them with supervision or operating instructions Warning For connection to the mains power supply use a multicore cable with a cross section of at least 4x1 5mm of the kind provided for bytheregulations mentioned above by way of example type H05 VV F cablecanbeused witha cross section of 4x1 5mm To connectauxiliary equipment use wires with a cross section o
28. ual 9 1 Traffic light layout Traffic light 1 must be positioned on the outside of the gate and traffic light 2 on the inside WARNINGS Place signs for speed limitation to Walking pace 9 2 Motor preheating layout The S probe must be positioned and fixed on the outside to detect exter nal temperature It is to be connected to respective terminals 7 8 on the preheating board WARNINGS Move the EBP solenoid lock and flashing light to 12 13 Fig A Ref 2 WARNINGS Set flashing light dipswitch ON RIGEL5 21 INSTALLATION MANUAL 10 1 TABLE A PARAMETERS MENU Parameter min max default personal Definition Description 2 rop 3sec 1205ec Automatic Closing Time Set the numerical value of the TCA automatic closing time from 3 to 120 seconds m D uarH t 3 sec 180 sec Operation time motor 1 Enter the numerical value corresponding to the working time from 3 to 180 seconds for motor 1 a uarH t 3 sec 180 sec Operation time motor 2 Enter the numerical value corresponding to the working time from 3 to 180 atc seconds for motor 2 PEd E Iasc 9sec 6 Pedestrian operation time Setthe pedestrian opening time of motor 2 from 3 to 90 seconds aPEn dELRO 4 Set the opening delay time for motor 1 with respect to motor 2 which tose 3 Opening d lay time for leat 1 be adjusted from 0 to 10 seconds Se 5
Download Pdf Manuals
Related Search