Monitor User Manual
Contents
1. the wall to ensure adequate ventilation Product failure may result from heat build up caused by poor ventilation ls wall 4 Bi e D S8 3 10cm 10cm 10cm Physical appearance may vary slightly depending on the model Moving the monitor Two persons or more are required to handle the monitor Hold the top and bottom frame firmly to move the monitor le Accessories p User Manual Guarantee Card Certificate Power Cable im see l pc Remote Contral These images are intended for reference only Refer to actual product Features The super speed infrared touch screen allows for smooth writing stable performance prompt response and HID It can support multi touch 2 point and 4 point with possibility to zoom in out drag and rotate the object selected It uses high quality FULL HD LED panel with features of high brightness high contrast ratio color optimization function bit by bit image dynamic and static screen enhancing function Optional PC box leaves no external cables Super slim esthetically pleasing frame just 8 cm Very low power consumption in standby mode Rounded corners ensure safety Additional USB and HDMI inputs in the front Power ON OFF by remote control Compatible with Windows Linux and other Operating Systems ie Control Panel Front frame Touch screen amp Di2. USB etc see fig cu The figure is intended for reference only cu You may have to prepare some connecting cables TV ports 090000000 Connecting to a projector 644444444 ee t gt You can connect the monitor to a projector as explained below Sack tow Connect VGA and HDMI output from PC Connect VGA output from extended interface e Installing the Wall Mount DRR Te i Tools Installation ENSE Installing and Using the Touch Screen Software I Setup TouchDev toulehdev Setup Load the attached disk into the CD ROM Customer Information Please enter your information Double click to run TouchDevSetup exe in the Please enter your name and the name of the company for which you work User Name disc nee 3 Complete installation accordingly Company Name EOGI Click Finish and run touch screen management application Fitouch exe The installation will be Next gt Cancel Touch touchdev Setup completed when L appears on the desktop s InstallShield Wizard Complete Setup has finished installing touchdev on your computer Em lower right hand NE Blue indicates the equipment has been connected Gray indicates the equipment has not been connected or a failed connection II Basic Function Run TouchDev exe By default the software will automatically execute the icon can Im be found
3. close to the 4 angles of the screen in the second the display icon is close to the center of the screen Note the first is recommended After selection click calibration The interface as shown in the figure on the left will appear Use a touch pen or your finger to touch the center of icon During positioning the touch pen must be vertical to the screen surface and pen point coiidide withthe centeraf icon 8 The positioning icon will move to the 4 angles of the screen upon touch For Touchboard mode the icon will also appear in the center of the screen Custom calibration Custom mode when selected supports two kinds of positioning 1 In custom mode two electronic white boards must be connected at the same time Custom mode is not supported in the case of one electronic whiteboard Options Configuration 2 Matching between two parts of the screen When the screen is split in two with separate performance on both parts at the same time and both parts requiring touch functionality carry out positioning on both sides first on the left then on the right Information The Basic box shows information regarding the current screen If there is more than one touch screen device a number will be assigned to each one and their specific information displayed The features box shows updated information regarding the touch screen V is supported and x is not su
4. on the desktop s lower right hand corner ERE so If you accidentally close the software click start program find and select TouchDev then run it By default the shortcut of TouchDev is on the desktop Double click it Main Menu Click the TouchDev icon The main menu will pop up as i i shown in the figure Functions include anguage Calibrate Language Lets you select the relevant language for the Option About Exit Calibration Lets you calibrate the screen so that the touch and interface actual location on the screen match Options Shows basic information regarding the touch screen allocates relevant parameters for real requirements About Shows other information regarding TouchDev Calibration Screen calibration Exit Closes TouchDev Standard calibration As shown in the figure on the left there are custom and advanced options for calibration If neither one of the two options is selected calibration will be standard Standard calibration is suitable when connecting only one electronic white board Calibrate mode includes TouchPanel touch screen and TouchBoard electronic white board Touchboard supports positioning of non rectangle screen and TouchPanel only supports positioning of rectangle screen When adopting a projector choose TouchPanel mode Under calibrate position you will find two positions 1 and 2 in the first the display icon is
5. SmartMedia www smartmediaworld net SMA series Touch Monitor User Manual Please read this manual very carefully before using your device and store in a safe place for future reference Take down the model number for reference Model No Serial No if Table of Contents Important Notes Accessories Features Control Panel Interface Remote Control Instructions Installing the Wall Mount Installing and Using the Touch Screen Software Specifications PC Specifications Touch Screen Specifications Monitor Toxic amp Hazardous Materials 13 14 18 18 19 20 e Important Notes For your safety please read this manual very carefully before use and keep it properly for any reference We will take no responsibilities for any accidents resulting from violation of the safety and usage guidelines in this Manual Explanation of Signs The signs used in this Manual and which are affixed on the product are listed below Please read the Manual carefully and make sure you fully understand these signs i This sign warns about the risk of serious personal injury or even death Warning due to incorrect operation A a This sign warns about the risk of personal injury or property damage NNotice ue to incorrect operation Hiah risk This sign warns of high voltage Only professional staff is allowed to g maintain and replace the parts to avoid fire or shock hazards AN Warning To avoid electri
6. Technology Sensing Object Non transparent object like pen finger etc Multi touch 2 point 4 point Single Touch click 8ms writing 3ms Response Time mts Monitor Specifications w se 9 Speakers 8W 8W PAL SECAM BG DK I 1920 1080 1920 1080 1920 1080 View Angle Image JPEG BMP PNG Multi Media Audio WMA MP3 M4A AAC Formats Video MPEG1 MPEG2 MPEG4 H264 RM RMVB MOV MJPEG VC1 DivX FLV Working 0 C to 40 C Temperature Working 1096 to 9096 No condensation Humidity Storing 20 C to 60 C Temperature Machine Size 1296 5x792 5x81mm 1550x944x96 5mm 1626x979x102mm Packing Size 1425x970x210mm 1650x1085x210mm 1755x1135x210mm Net Weight 40kg 55kg 60kg c The design and specifications may be changed without any prior notice c Please refer to the labels on the product and packing for power and power consumption information e Toxic and Hazardous Materials or Elements 9 and Hazardous Materials or Elements Toxic re Hazardous Material iten Hexavalent Polybrominated Lead Mercury Chromium Polybrominated Chrome Diphenyl Ethers PH HG CD Biphenyl PBB Cr VI PBDE EE LCD LED panel Speakers kers o indicates that content of such material in the parts is below the limit of SJ T11363 2006 x indicates that the content of such material in the parts is above the limit of SJ T11363 2006 The substance marked with x falls into the category that ca
7. c shock do not open the back cover There are no parts inside that users can fix Turn to a professional if you encounter any problems Do not insert any metal parts into the openings of the monitor to avoid electric shock Do not install this monitor on an unstable surface such as a loose shelf a sloping floor or an insecure wall Turn off the power and contact the local dealer if the monitor falls to the ground or gets damaged Keep the monitor away from rain and do not install in places near water e g bathtub basin wet floor etc If the monitor accidentally gets wet disconnect the power unplug from the power source and contact your local dealer The openings on the back cover are designed for ventilation and allow heat to escape Do not block these openings and use the monitor only in adequately ventilated places Make sure the power outlet is in good condition before plugging the monitor to avoid electric shock or damage Unplug the power cable and TV tuner during bad weather and thunderstorms to avoid damage Clean the monitor with a soft cloth Never use harsh chemicals to clean your monitor Do not use any object or material that can scratch the surface or cause friction or indentations Do not affix stickers labels or gummed paper to the touch screen Keep it clean Avoid dropping the remote control Make sure you have enough space for installation Allow the necessary distance between the monitor and other objects e g
8. l The monitor will turn off automatically if something is blocking the sensor within a 10 cm distance for 8 10 seconds jr 10cm a 5 5 Shelter M ccce r Fi nmm jooo oo Distance sensor Select Signal Source Via the buttons on the control panel ey Press SOURCE button on front control panel the sources will be listed as shown on the right Press P or P to select signal source Press SOURCE button on front control panel to confirm the signal source selected Via remote control Press SOURCE BUTTON on remote control the sources will be listed as shown on the right 2 Press A or V to select signal source G Press SOURCE button on remote control to confirm the signal source selected Auto Switch Source Both the built in PC optional and HDMI port on the front control panel are in HDMI 1 source as default setting When you connect an external PC to the HDMI port on the front control panel the source will be automatically switched to HDMI 1 When the built in PC optional and the HDMI port on the front control panel Input Source are connected at the same time you must unplug the HDMI connection on the front control panel and external PC in order to have the signal source from the built in PC Installing and Removing the built in PC optional The built in PC box allows for easy installation and maintenance The PCis built into the back of the monitor Loosen the scre
9. nnot be removed or replaced by the technology from a scientific point of view EU RoHS Directive 2002 95 EC not in the listed materials of restricted content under SJ T11363 2006 of PR China except Taiwan Hong Kong and Macao
10. ol EXIT exit P P program previous next SLEEP timed sleep BACKWARD FORWARD backward forward Use keys for multi media Replacement of Remote Control Battery Instructions Turning on the monitor When the power cable is connected the TV indicator on the front control panel is red Press the POWER button on the front control panel or the remote control the TV indicator in red will flash for 5 seconds then the TV and built in PC optional will be turned on The monitor indicator will be blue and the built in PC indicator will be green To turn on the monitor alone press POWER button to turn on the PC and monitor as above then switch off the PC via the operating system Turning off the monitor The monitor and built in PC optional can be turned off with one button as follows Initial State State after pressing POWER single button solution PC is OFF monitor is ON Monitor will be turned off Both PC and TV are On PC will be turned off first then the monitor e If you need to turn both monitor and in built PC OFF immediately press POWER button for 3 seconds Turning off the backlight Press SLEEP button on the front control panel to turn off the monitor backlight The monitor indicator will change from blue to red and the other parts of the monitor will still be working Press SLEEP button again to turn on the backlight f Distance Sensing There is a distance sensor built into the front control pane
11. pported Upgrading method related authorized documents are needed before upgrading Click x in features to show the upgrading box Click upgrade to search for the authorized documents for upgrading For service parameters configuration we suggest using the default value unless there is a specific requirement Description of parameters right button enabling select Yes to use right button select No the right button is disabled Delayed time length Sets the time length for right button enabling Fault tolerant space Errors while pressing on the screen with the hand errors within a range are permitted Sleek coefficient set sampling points to ensure data points sent to the system are smooth and to avoid excessive vibration of scribing line EN CE III Basic Operation General operation The following operations may be performed on the screen Click object on the screen Double click click the same object twice quickly on the same screen Drag press the object and drag it Right key press the object and remain for 2 3 second ENTE PC Specifications Mini ITX Intel H61 chipset Intel QM67 chipset Intel1155 Pentium 13 I5 17 The model Intel I3 15 17 The model no is subject to CPU no is subject to the real products the real products Integrated Intel R HD Graphics Integrated Intel R HD Graphics Touch Screen Specifications Touch technology Non contact Infrared Sensing
12. splay amp Touch area Remote contral sensor Q Indicator of TV power amp Indicator of PC power Distance sersor Launch amp Distance sersor receive p CJL LDL OOOOOOOe lili o HDMI 1 input USB Host for PC connection USB Touch for touch screen connection Volume Channel TV function menu Source Key for LED backlight on off Key for all in one machine PC power indicator lights up in models with built in PC Interface mini ITX PC OPS id 5 3 3 Ssmi o o irs cl t PEE HIT s i USB 2 0 2 only Ethernet VGA 2 Mri e Power on off Reset amp Audio output e Audio output Microphone port 8 Mic ndicator of power B D Indicator of HDD PS t Power on off CO c eese D O099999900 ma ty 4 44 4A A144 Power plug in YPbPr signal in i medi e YPbPr audio in e HOMO AV videoin VGA AV audio in Audio corresponding to VGA s NE di SPDIF output Multi media Audio output 3 5mm AV output NES Remote Control TV TV input Power power on standby YPBPR YPBPR input AV AV input MENU enter control menu ENTER enter SOURCE signal source selection 0 9 numeric key VOL VOL volume down up PSM picture effect SSM sound effect PREV NEXT previous next STOP stop PLAY play VGA VGA input MUTE sound off USB multi media by USB HDMI HDMI input INFO working state cursor contr
13. ws and grasp the PC to move it out smoothly ce Do not remove the PC if it is functioning properly If it is necessary to remove it disconnect the power from the monitor first ce Installation is the same for OPS and Mini ATX PCs Remove the 2 screws Back view of all in one Take out PC alone the direction showed ENTE Connecting To External PC If necessary you can connect your monitor to an external PC for interactive operation D Connecting to interface on front control panel Front view This monitor has a port on the front control panel for easy operation Connect the HDMI cable for video and audio signals connect the USB cable for touch screen functionality Interface parts on front control panel c HDMI and USB cables may or may not be included in your supply Check with your dealer in advance USB touch 2 Connecting to the ports on the back of your monitor Connect the VGA and audio cables to transmit the signal from the external PC to the monitor Then connect USB cable for touch screen functionality Connection by HDMI can replace the VGA and Audio cables dq Interface ports af tv board d ed e oc Interface ports of front control panel HDMI Coo USB Touch VGA Bh Connecting Other External Equipment to the monitor You can connect other external equipment like a PC or a DVD to the monitor via VGA HDMI YPBPR AV
Download Pdf Manuals
Related Search