User manual
Contents
1. This icon is not used on this transceiver Appears when performing Scan Appears when the key programmed as RF Power LO is pressed Appears while using the telephone system 12 Appears when you have a message Displays the group name or the system group number with up to 10 digits The remaining 2 digits are used for various indicators PROGRAM MABLE AUXILIARY FUNCTIONS Keys 8 and 09 pages 10 and 11 can be programmed with the auxiliary functions listed in the following table The keys can only be programmed with functions depending on whether you are using Conventional Format or Trunking Format Please contact your dealer for further details on these functions Function Auto Telephone Conventional Format Trunking Format Channel Down Channel Up Channel Up Down Display Character DTMF ID BOT DTMF ID Emergency 2 Group Down Group Up Group Up Down Home Channel Home Group Key Lock Lamp Memory RCL STO Memory RCL Memory STO Message Mode 3 Function Monitor Momentary Conventional Format Trunking Format Monitor Toggle None Operator Selectable Tone Redial RF Power Low Scan Scan Del Add Scan Temporary Delete SP Attenuation Squelch Level Squelch Off Momentary Squelch Off Toggle System Down Sys2. VHF FM TRANSCEIVER TK 2140 UHF FM TRANSCEIVER TK 3140 KENWOOD CORPORATION B62 1476 00 K 09 08 07 06 05 04 03 02 01 00 THANK YOU We are grateful you chose KENWOOD for your land mobile radio applications We believe this easy to use transceiver will provide dependable communications to keep personnel operating at peak efficiency KENWOOD transceivers incorporate the latest in advanced technology As a result we feel strongly that you will be pleased with the quality and features of this product MODELS COVERED BY THIS MANUAL e TK 2140 VHF FM Transceiver e TK 3140 UHF FM Transceiver NOTICES TO THE USER Government law prohibits the operation of unlicensed radio transmitters within the territories under government control Illegal operation is punishable by fine and or imprisonment Refer service to qualified technicians only SAFETY It is important that the operator is aware of and understands hazards common to the operation of any transceiver WARNING EXPLOSIVE ATMOSPHERES GASES DUST FUMES etc Turn off your transceiver while taking on fuel or while parked in gasoline service stations more of the following statements be applicable FCC WARNING This equipment generates or uses radio frequency energy Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction
3. RECEIVING SCAN Conventional Format Priority SCAN 2 TONE SIGNALLING Conventional Format FleetSync ALPHANUMERIC 2 WAY PAGING FUNCTION 26 Key Functions SELCALL SELECTIVE CALLING Status 55 OpTionaL SHorT FEATURE AUDIBLE USER FEEDBACK TONES UNPACKING AND CHECKING EQUIPMENT Note The following unpacking instructions are for use by your KENWOOD dealer an authorized KENWOOD service facility or the factory Carefully unpack the transceiver We recommend that you identify the items listed in the following table before discarding the packing material If any items are missing or have been damaged during shipment file a claim with the carrier immediately SUPPLIED ACCESSORIES Belt clip Part Number J29 0688 XX Quantity Univeral connector cap 09 0625 Dressed screw Warranty card 08 0548 Instruction manual B62 1476 XX Belt clip Universal connector cap Dressed screw PREPARATIO Battery Pack PRECAUTIONS Nemon Do not recharge the battery pack if it is already fully charged Doing so cause the life of the battery pack to shorten or the battery pack may be damaged After recharging the battery pack disconnect it from the charger If the charger power is reset turned ON after being turned OFF recharging will start again and the battery pack will become overcharged Do not use the transceiver w
4. calling ID or text message will appear when a Status call is received The display alternates between the caller ID and the message Press any key to return to Normal Operation Mode Reviewing the Messages the Stack Memory 1 Press and hold the A key for more than 1 second to enter Stack Mode The last received message is displayed with the message number S Status appears with the number Use the encoder to select the message you want to view if more than one message is stored in the stack memory Press the 4B key or CP key to stop the message from auto scrolling if desired Also use these keys to scroll through the message manually Press the S key to toggle between the message and the caller s ID To erase the message press and hold the S key for more than 1 second 30 Automatic Status Response If you pre select a status number and then leave the transceier in Status Mode the transceiver will automatically respond with that status number when a request from the base station is received The base station request function is optional SHoRT Messaces FEATURE Received short messages maximum of 48 characters are displayed the same as Status messages page 28 however only 4 short messages can be stored in the stack memory M Message and the message number appear with the message 31 AUDIBLE USER FEEDBACK TONES The transceiver emits various ton
5. When storing the battery pack for a long period 1 Remove the battery pack from the equipment 2 Discharge the battery pack if possible 3 Store the battery pack in a cool below 25 C and location Characteristics of the Li ion Battery Pack As the battery pack is charged and discharged repeatedly the battery capacity decreases Even if the battery pack is unused the battery pack degrades It takes a longer time to charge the battery pack in cooler areas The life of battery pack is shortened when it is charged and discharged in hotter areas When the battery pack is stored ina hot location the battery pack degrades quicker Do not leave the battery pack in vehicles or near heating appliances When the battery pack operating time becomes short even if it is fully charged replace the battery pack Continuing to charge and discharge the battery pack may result in elecrolyte leakage NSTALLING REMOVING THE OPTIONAL RECHARGEABLE BATTERY Pack or ALKALINE BATTERY Case 1 Match the guides of the battery pack with the corresponding grooves on the upper rear of the transceiver then firmly press the battery pack to lock it in place 2 Flip the safety catch into place to prevent accidentally pressing the release latch and removing the battery 3 To remove the battery pack lift the safety catch press the release latch then pull the battery pack away from the transceiver Note Whe
6. is a voice call to a particular station or to a group of stations Transmitting 1 Select your desired system and group or group and channel Press the A key to enter Selcall Mode Use the encoder to select the ID of the station you want to call 4 Press the PTT switch and begin your conversation Receiving An alert tone will sound the transceiver will automatically enter Selcall Mode and the calling station s ID will appear when a Selcall is received To respond to the call press the PTT switch and speak into the microphone 27 View the Caller IDs in the Stack Memory The mail icon M will flash when a Selcall call is received and stacked 1 Press and hold the A key for more than 1 second to enter Stack Mode last received Caller is displayed with the Caller ID number I ID appears with the number Use the encoder to select the ID you want to view if more than one ID is stored in the stack memory To erase the ID press and hold the S key for more than 1 second E identification Codes An ID code is a combination of a 3 digit Fleet number and a 4 digit ID number Each transceiver must have its own Fleet and ID number Enter Fleet number 100 349 to make group call Enter an ID number 1000 4999 to make an individual call in your fleet Enter a Fleet number followed by an ID number to make an individual call in your desired fleet Int
7. on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure INSTALLING THE BELT Note When first installing the belt clip you must remove the battery pack from the rear of the transceiver 1 Remove the two screws from the rear of the transceiver then remove the small plastic black covering that was held in place 2 Insert the belt clip mount into the space on the rear of the transceiver 3 Using the 2 screws affix the belt clip in place INSTALLING THE COVER OVER THE UNIVERSAL CONNECTOR If you are not using the optional KMC 25 speaker microphone install the cover over the univeral connector using the supplied 4 x 6 mm dressed screw INSTALLING THE OpTIONAL 25 Speaker MICROPHONE 1 Insert the guide of the speaker microphone connector into the groove of the universal connector 2 Secure the connector in place using the attached screw GETTING ACQUAINTED 5 CoC IWC Antenna connector Connect an optional antenna here Rotary encoder Rotate this encoder to activate its programmable function System or Group Up Down in Trunking Format and Group or Channel Up Down in Conventional Format For further details contact your dealer 10 POWER switch VOLUME control Turn clockwise to switch ON the transceiver Rotate to adjust the v
8. e group number and that group becomes the revert group Simply press the PTT switch to respond to the call You can also perform Group Scan while using a priority channel Please contact your dealer for information concerning Priority Scan 22 CONVENTIONAL OPERATION Conventional Format TRANSMITTING 1 Select the desired group and channel using the encoder and the Group or Channel keys Press the key programmed as Monitor to check whether or not the channel is free If the channel is busy wait until it becomes free Press the PTT switch and speak into the microphone Release the PTT switch to receive For best sound quality at the receiving station hold the microphone approximately 1 5 inches 3 4 cm from your mouth Receiving 1 Select the desired group and channel using the encoder and the Group or Channel keys If the Scan function has been programmed you can switch it ON or OFF as desired When you hear a caller s voice readjust the volume as necessary 23 SCAN Conventional Format If the Scan function is programmed groups or channels can be scanned by pressing the key programmed as Scan Scan be used as either Single Scan or Multi Scan Single Scan monitors only the channels of a single group Multi Scan monitors all channels of every group When the Scan key is pressed the SCN indicator and SCAN or the revert group channel number appear on the display and scannin
9. er fleet call Select Fleet and ALL ID to make a call to all units Broadcast call Select ALL Fleet and enter an ID number to make a call to the selected ID in all fleets Supervisor call Note Broadcast and Supervisor calls are programmed functions that cannot be made with a keypad The ID range may be limited by programming 28 Status MESSAGE You can send and receive 2 digit Status messages 10 79 which be decided in your talk group Messages can contain up to 16 alphanumeric characters A maximum of 9 received messages can be stored in the stack memory of your transceiver These saved messages can be reviewed after reception If the stack memory is full the oldest message will be erased when a new message is received mail icon M lights when a message is stored in the stack memory Note All stored messages will be cleared when the transceiver power is turned OFF E Transmitting 1 Select your desired system and group or group and channel Press the A key to enter Selcall Mode Press the 4B key or CD key to select the ID of the station you want to call Press the A key to enter Status Mode Press the 4B key or key to select the status you want to transmit 6 Press the PTT switch to initiate the Status call e COMPLETE is displayed when the call has been successfully transmitted 29 Receiving The icon will flash and
10. es to indicate the transceiver s operating status Contact your dealer for further information on these tones Conventional Trunking Format Format Alert Busy Delay Deny Free System Ring Back Mode System Search Mode Group Call Individual Call Intercept Key Input Error Key Press A Key Press B Key Press C Password Agreement Power ON Pre Alert Proceed Queue Ringing Roll Over System Search System Search End
11. g conventional systems the revert groups and the groups not locked out of the scanning sequence are scanned See GROUP SCAN on page 22 20 Scan Lockout If a programmable auxiliary key is programmed with Scan Del Add each system can be locked out of the scan sequence manually The delete indicator will appear on the display when the selected system is locked out Scan REVERT You can select revert systems and groups using the encoder and the System or Group keys Four types of Scan Reverts which can be programmed by your dealer are available e Last Called Revert The last system group received is assigned as the new revert system and group Last Used Revert The last system group responded to is assigned as the new revert system and group Selected The last system group selected is assigned as the new revert system and group Selected Talkback If the system group has been changed during Scan the newly selected system group is assigned as the new revert system and group The transceiver talks back on the current receive group 21 GROUP SCAN Trunking Format Group Scan is available for both trunked and conventional systems This feature is useful when more than one group is programmed in a system Group Scan is set by your dealer on request It scans the revert groups as well as groups that are allowed to be scanned When is received the group indicator shows th
12. g starts When a call is received scanning stops and the group and channel digits appear Press the PTT switch and speak into the microphone to respond to the call The transceiver will continue scanning after an adjustable time delay if the PTT switch is released and no further signal is received When the displayed group is not locked out of the scanning sequence the add indicator v will appear the display Priority SCAN The priority channel must be programmed in order for Priority Scan to function The transceiver will automatically change to the priority channel when a signal is received on it even if a signal is being received on a normal channel The indicator appears when the displayed channel is the priority channel 24 2 SIGNALLING Conventional Format ee eee 2 Tone Signalling is either activated or deactivated by your dealer 2 Tone Signalling only opens the squelch when the transceiver receives two tones corresponding to those set up in the transceiver When the squelch opens you will be able to hear the caller without any further action After a correct 2 Tone signal is received and the squelch opens pressing the key programmed as Monitor will cancel the connection If your dealer programmed Transpond for 2 Tone Signalling your transceiver will automatically send an acknowledgment signal to the station that called you with the correct 2 Tone signal Transpond does not funct
13. hile charging the battery pack We recommend you switch the transceiver power OFF while charging is taking place Do not short the battery terminals or dispose of the battery by fire Never attempt to remove the casing from the battery pack Information concerning the optional Li ion battery pack The battery pack includes flammable objects such as organic solvent Mishandling may cause the battery to rupture producing flames or extreme heat deteriorate or cause other forms of damage to the battery Please observe the following prohibitive matters Do not disassemble or reconstruct battery The battery pack has a safety function and protection circuit to avoid danger If they suffer serious damage the battery may generate heat or smoke rupture or burst into flame Do not short circuit the battery Do not join the and terminals using any form of metal such as a paperclip or wire Do not carry or store the battery pack in containers holding metal objects such as wires chain neckless or hairpins If the battery pack is short circuited excessive current will flow and the battery may generate heat or smoke rupture or burst into flame It will also cause metal objects to heat up Do not incinerate or apply heat to the battery If the insulator is melted the gas release vent or safety function is damaged or the electrolyte is ignited the battery may generate heat or smoke rupture or burst into flame Do not u
14. ing the encoder and the keys programmed with System or Group Up Down Select the desired group and channel Conventional Format using the encoder and the keys programmed with Group or Channel Up Down Timer purpose of the Time out Timer is to prevent any caller from using a channel for an extended period of time If you continuously transmit for a period of time that exceeds the programmed time the transceiver will stop transmitting and an alert tone will sound To stop the tone release the PTT switch Your dealer can program the TOT time in the range of 15 seconds to 10 minutes TRUNKED OPERATION Trunking Format A DispatcH CALL 1 Select the desired system and group using the encoder and the System or Group keys 2 Press the PTT switch then speak into the microphone Release the PTT switch to receive For best sound quality at the receiving station hold the microphone approximately 1 5 inches 3 4 cm from your mouth Receivine DispatcH CALL 1 Select the desired system and group using the encoder and the System or Group keys Ifthe Scan function has been programmed you can switch it ON or OFF as desired 2 When you hear the dispatcher s voice readjust the volume as necessary CONVENTIONAL OPERATION Trunking Format TRANSMITTING 1 Select the desired system and group using the encoder and the System or Group keys Press the key p
15. ion when you are called as a Group call If your dealer programmed Tone Alert for 2 Tone Signalling your transceiver will emit a beep when the correct 2 Tone signal is received Note This transceiver is only capable of decoding 2 Tone Signals It cannot encode a 2 Tone Signal 25 ALPHANUMERIC 2 WAY PAGING FUNCTION FleetSync is an Alphanumeric 2 way Paging Function and is a protocol owned by KENWOOD Corporation FleetSync enables a variety of paging functions on your transceiver some of which depend on dealer programming Key Function Press to change the transceiver mode as shown in the diagram below Press while in Stack Mode to toggle between the received message and the caller s ID Press and hold for more than 1 second to delete the displayed message Press to stop auto scrolling received messages Also press to scroll manually Press to initiate a call Normal Operating Mode Hold A for Press 1 second any key New Message Stack Mode Display Mode Hold A for 1 second Receive anew message Press A or receive a Selcall Press A lt lt Selcall Mode Press A Press A Status Mode Depending on how your dealer programmed the transceiver Selcall Mode may be skipped or the transceiver may exit Selcall Mode automatically as shown by the dash arrow 26 SELCALL SELECTIVE CALLING A Selcall
16. leaking battery If the electrolyte liquid from the battery gets into your eyes wash your eyes out with fresh water as soon as possible without rubbing your eyes Go to the hospital immediately If left untreated it may cause eye problems Do not charge the battery for longer than the specified time If the battery pack has not finished charging even after the regulated time has passed stop it The battery may generate heat or smoke rupture or burst into flame Do not place the battery pack into a microwave or high pressure container The battery may generate heat or smoke rupture or burst into flame Keep ruptured and leaking battery packs away from fire If the battery pack is leaking or the battery emits a bad odor immediately remove it from flammable areas Electrolyte leaking from battery can easily catch on fire and may cause the battery to generate smoke or burst into flame Do not use an abnormal battery If the battery pack emits a bad odor appears to have different coloring is deformed or seems abnormal for any other reason remove it from the charger or operating equipment and do not use it The battery may generate heat or smoke rupture or burst into flame Using the Li ion Battery Pack Charge the battery pack before using it To keep the battery discharge at a minimum remove the battery pack from the equipment when it is not in use Store the battery pack in a cool and dry location
17. manual The user could lose the authority to operate this equipment if an unauthorized change or modification is made INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can generate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer for technical assistance ATTENTION U S A Only The RBRC Recycle seal found on KENWOOD nickel cadmium Ni Cd battery packs indicates KENWOOD s voluntary participation in an industry program to collect and recycle Ni Cd batteries after Gy their operating life ha
18. n lifting the safety catch make sure you do not lift both the catch and the release latch at the same time as you may inadvertantly damage the release latch This is especially true when using an implement such as a small screw driver to lift the safety catch INSTALLING RemovinG ALKALINE BATTERIES Do not install batteries in a hazardous environment where sparks could cause an explosion Never discard old batteries in fire extremely high temperatures cause batteries to explode Do not short circuit the battery case terminals Do not use commercially available rechargeable batteries Note If you do not plan to use the transceiver for a long period remove the batteries from the battery case This battery case has been designed for transmitting at a power of approximately 1 W the low power setting on your transceiver If you want to transmit a stronger signal using the high power setting on your transceiver use an optional rechargeable battery pack 1 To open the battery case press on the two tabs on the upper rear of the case then pull the two halves apart 2 Insert 6 AA LR 6 alkaline batteries into the battery case Be sure to match the polarities with those marked in the bottom of the battery case 3 Align the tabs of the cover with the base then push down on the cover until it locks in place INSTALLING THE OPTIONAL ANTENNA Screw the antenna into the connector
19. olume Turn counterclockwise fully to switch OFF the transceiver 4 Transmit Battery low indicator This red LED lights during transmission If programmed by your dealer when the battery pack power is low the LED flashes during transmission Replace or recharge the battery pack Auxiliary orange key Press to activate its auxiliary function page 13 Battery pack safety catch Flip this catch to prevent accidentally pressing the battery pack release latch See INSTALLING REMOVING THE OPTIONAL RECHARGEABLE BATTERY PACK OR ALKALINE Case on page 6 Battery pack release latch Press this latch to release the battery pack See INSTALLING REMOVING THE OPTIONAL RECHARGEABLE Battery ALKALINE Case on page 6 PTT Push To Talk switch Press this switch then speak into the microphone to call a station Side 1 Side 2 keys Press to activate their auxiliary functions page 13 10 S A 4B and keys Press to activate their auxiliary functions page 13 Universal connector Connect the optional KMC 25 speaker microphone here Otherwise keep the supplied cover in place 11 DISPLAY Indicator sve AM TTT TTT Description Displays the channel or group number in conventional mode and the system or group number in trunking mode Appears when performing Priority Scan Appears when the key programmed as Monitor is pressed
20. rogrammed as Monitor to check whether or not the channel is free If the channel is busy wait until it becomes free Press the PTT switch and speak into the microphone Release the PTT switch to receive For best sound quality at the receiving station hold the microphone approximately 1 5 inches 3 4 cm from your mouth RECEIVING 1 Select the desired system and group using the encoder and the System or Group keys If the Scan function has been programmed you can switch it ON or OFF as desired When you hear the dispatcher s voice readjust the volume as necessary SYSTEM SCAN Trunking Format If the Scan function is programmed systems can be scanned by pressing the key programmed as Scan When the Scan key is pressed the SCN indicator and SCAN or the revert system group number appear on the display and scanning starts The systems not locked out of the scanning sequence are scanned When call is received scanning stops and the system and group digits appear Press the PTT switch and speak into the microphone to respond to the call The transceiver will continue scanning after a predetermined time delay if the PTT switch is released and no further signal is received SCANNING TRUNKED SYSTEMS When scanning trunked systems the revert groups and the groups not locked out of the scanning sequence are scanned See GROUP SCAN on 22 Scanning Conventional Systems When scannin
21. rst into flame Do not jar or throw the battery An impact may cause the battery to leak generate heat or smoke rupture and or burst into flame If the battery s protection circuit is damaged the battery may charge at an abnormal current or voltage and an abnormal chemical reaction may occur The battery may generate heat or smoke rupture or burst into flame Do not use the battery pack if it is damaged The battery may generate heat or smoke rupture or burst into flame Do not solder directly onto the battery If the insulator is melted or the gas release vent or safety function is damaged the battery may generate heat or smoke rupture or burst into flame Do not reverse the battery polarity and terminals When charging a reversed battery an abnormal chemical reaction may occur In some cases an unexpected large amount of current may flow upon discharging The battery may generate heat or smoke rupture or burst into flame Do not reverse charge or reverse connect the battery The battery pack has positive and negative poles If the battery pack does not smoothly connect with a charger or operating equipment do not force it check the polarity of the battery If the battery pack is reverse connected to the charger it will be reverse charged and an abnormal chemical reaction may occur The battery may generate heat or smoke rupture or burst into flame Do not touch a ruptured and
22. s expired program is an alternative to disposing Ni Cd batteries with your regular refuse or in municipal waste streams which is illegal in some areas For information on Ni Cd battery recycling in your area call toll free 1 800 8 BATTERY 1 800 822 8837 KENWOOD s involvement in this program is part of our commitment to preserve our environment and conserve our natural resources CONTENTS UNPACKING AND CHECKING EQUIPMENT SUPPLIED ACCESSORIES PREPARATION Battery Pack PRECAUTIONS INSTALLING REMOVING THE OPTIONAL RECHARGEABLE BATTERY Pack ALKALINE Battery INSTALLING REMovING ALKALINE BATTERIES INSTALLING THE OPTIONAL ANTENNA INSTALLING THE BELT INSTALLING THE COVER OVER THE UNIVERSAL CONNECTOR INSTALLING THE OPTIONAL 25 Speaker MICROPHONE 9 GETTING ACQUAINTED DisPLay PROGRAMMABLE AUXILIARY FUNCTIONS OPERATION OVERVIEW TRUNKING FoRMAT ConVENTIONAL FORMAT OPERATING BASICS Switcuinc Power OFF THE VOLUME SELECTING System Group CHANNEL Time out Timer TOT TRUNKED OPERATION Trunking Format a DispatcH CALL REcelvin a DispatcH Ne CONVENTIONAL OPERATION Trunking Format TRANSMITTING RECEIVING SYSTEM SCAN Trunking Format SCANNING TRUNKED SYSTEMS SCANNING CONVENTIONAL SYSTEMS Scan Lockout Scan REVERT GROUP SCAN Trunking Format CONVENTIONAL OPERATION Conventional Format TRANSMITTING
23. se or leave the battery near fires stoves or other heat generators areas reaching over 80 C If the polymer separator is melted due to high temperature an internal short circuit may occur in the individual cells and the battery may generate heat or smoke rupture or burst into flame Do not immerse the battery in water or get it wet by other means If the battery s protection circuit is damaged the battery may charge at extreme current or voltage and an abnormal chemical reaction may occur The battery may generate heat or smoke rupture or burst into flame Do not charge the battery near fires or under direct sunlight If the battery s protection circuit is damaged the battery may charge at extreme current or voltage and an abnormal chemical reaction may occur The battery may generate heat or smoke rupture or burst into flame Use only the specified charger and observe charging requirements If the battery is charged in unspecified conditions under high temperature over the regulated value excessive high voltage or current over regulated value or with a remodelled charger it may overcharge or an abnormal chemical reaction may occur The battery may generate heat or smoke rupture or burst into flame Do not pierce the battery with any object strike it with an instrument or step on it This may break or deform the battery causing a short circuited The battery may generate heat or smoke rupture or bu
24. tem Up System Up Down Talk Around Telephone Disconnect 1 These functions be programmed only on key the encoder 2 This function can be programmed only on key 5 the Auxiliary orange key This function can be programmed only on key 975 A key 4 This function can be programmed only on the programmable function key of the optional KMC 25 speaker microphone 14 OPERATION OVERVIEW Your dealer can program your transceiver for either Trunking Format or Conventional Format TRUNKING FORMAT This format can handle up to 32 systems with up to 250 groups in each system The transceiver can be used in both trunked mode and conventional mode Systems groups and their functions are programmed by your dealer CoNVENTIONAL FoRMAT This format can handle up to 250 groups with 250 channels in each group The transceiver can be used only in conventional mode Groups channels and their functions are programmed by your dealer OPERATING BASICS SwitcHinc Power OFF Turn the Power switch Volume control clockwise to switch the transceiver ON Turn the Power switch Volume control counterclock wise to switch the transceiver OFF ADJUSTING THE VOLUME Rotate the Power switch Volume control to adjust the volume Clockwise increases the volume and counter clockwise decreases it SELECTING A System Group CHANNEL Select the desired system and group Trunking Format us
Download Pdf Manuals
Related Search