Dear valued customer, To discover a De Dietrich product is to
Contents
1. New appliance POSSIBLE CAUSES Nothing The smell will dis appear after several uses WHAT SHOULD YOU DO The hob does not operate and the indicator lights on the con trol panel do not light up The machine is not connected to the power source The power source or connection is defective Inspect the electrical cir cuit breaker and fuses The hob is not working and another message is displayed The electronic board is func tioning poorly Call the After Sales Service Department The hob does not function the information A 7 is displayed e While in use YOU OBSERVE THAT The hob is locked POSSIBLE CAUSES See chapter on using the child safety system WHAT SHOULD YOU DO The hob has stopped operating and is beeping approximately every 10 seconds and a or F7 is displayed There was an overflow or an object is in contact with the control panel Clean the hob or remove the object then begin cooking again A series of small or F7 is displayed The electronic circuits have overheated See Inserting section After turning on a heating zone the indicator lights on the con trol panel continue to flash The cookware used is not suit able for induction or is less than 12 cm in diameter 10 cm on a 16 cm area See section on cookware for induction The saucepans make noise dur ing cooking Your hob makes a clicking sound du2. Certificate showing that the work complies with all the relevant standards Only a licensed person will have insu rance protecting their workmanship for 6 years Make sure you use a licensed person to install this product and ask for your Compliance Certificate 1 The Warranty only applies provided that the appliance has been used in accordance with the manufacturer s instructions and pro vided that the appliance has not been dama ged by an accident misuse neglect or abuse of any person other than the manufacturer or MEA or from faulty installation mis adjust ment or tampering by unauthorised persons 2 When a service inspection reveals the alle ged fault or faults are caused by incorrect operation contrary to the instruction manual and otherwise the appliance is in good order and working condition the purchaser shall be liable for a service fee charged by MEA or one of its Service Providers 3 If the appliance is used in Commercial Applications or for Rental purposes a sepa rate warranty of Twelve 12 months covering all parts with Three 3 months on the labour will apply 4 Subject to the provisions of any applicable statute this Warranty applies to the original retail purchaser only and is not transferable 5 Subject to the provisions of any applicable statute at no time does MEA have liability for freight transport or travel costs outside nor mal service areas 6 None of the above Warranties pu
3. be connected to the mains using a socket in compliance with publication CEI 60083 or an all pole circuit breaker device in compliance with the installation rules in force When power is first supplied to your hob or after an extended power cut an indicator light will appear on the control panel This information will disappear after 30 seconds e Hook up of 220 240V Green yellow NL Neutral Phase Earth Special connection DTI1177X e 220 240 V monophase hook up 16 and 32 amp fuses 2 Phase L Blue Neutral N 16 A Green yellow Ground 63 amp fuse Brown Phase L Blue Neutre N Green yellow Terre Neutral N 32 A Phase L Green yellow Ground Green yellow Blue al _Blue Brown Black grey Black grey WN Warning If the cable is damaged it must be replaced by the manufacturer its after sales service or a person with a similar qualification to prevent danger EN 2 USING YOUR APPLIANCE We have designed this cooking hob for use by private individuals in their homes These cooking hobs are intended exclusively for cooking beverages and foodstuffs and do not contain any asbestos based materials This appliance is not intended to be used by persons including children with reduced physical sen sory or mental abilities or persons lacking experience or awareness unless using it with the help of a person reponsible for their safety or under supervision and with prior instruction in
4. button M briefly The information is displayed on the new burner The original cooking zone switches off when the set tings are displayed on the new zone If there is no pan present before button M is pressed along beep sounds and the function is cancelled If button M is pressed and more than one pan is moved the function is cancelled and NO appears in the display 12 For models 1047CG DTI1167XE and DT1I1177X if you move a pan from one com plete cooking zone to another complete coo king zone the function is cancelled and NO appears in the display If the Switch function activates more than one new zone the function is cancelled and NO appears in the display Adjustment of power presets This function allows you to change the power levels defined in the presets except for the boost Your cooking hob must be turned off Select the preset I to be changed by kee ping your finger on it Set the new power level by sliding your finger over the power slider A beep will confirm your action after a few moments N B The power levels must be between 1 and 5 for the first button 4 by default 6 and 10 for the second 8 by default 11 and 15 for the third 15 by default 2 USING YOUR APPLIANCE EN e Child safety This function allows you to lock your hob when it is shut off or when it is cooking To lock Press button L until you hear a beep and the indicator ligh
5. its use Children should be supervised to ensure that they do not play with the appliance The induction principle The principle of induction is based on a mag netic effect When you place your cookware on a cooking zone and you turn it on the electronic circuits in your cooking hob produce induced cur rents in the bottom of the cookware which instantly raise its temperature This heat is then transmitted to the food To help you choose a list of cookware is pro vided with this guide A Induction plate B Electronic circuit C Induced currents e Cookware Most cookware is compatible with induction To verify that your cookware is suitable place it on a heating area on power 4 If the display remains on your cookware is compatible If the display flashes your cookware cannot Cooking Diameter of base be used with induction cooking area of cookware You can also use a magnet to test the cook te ware If a magnet sticks to the bottom of the cook Front or rear CONTINUUM e Choosing a cooking area ware it is compatible with induction Only glass terra cotta aluminium without a special finish on the bottom copper and some non magnetic stainless steels do not work with induction cooking We recommend that you select cookware with a thick flat bottom 12 32 cm for DTI1049X 15 32 cm for DTI1049XE Complete CONTINUUM 2 USING YOUR APPLIANCE EN Description of th
6. 7pm Customer service department 0892 02 88 04 PconreNTS en 1 INSTALLING YOUR APPLIANCE e Installation e Connection 2 USING YOUR APPLIANCE e The induction principle Description of your top e Using a cooking zone e Additional functions Boil Independent timer Delayed cooking Switch Preselected power settings Child safety Clean lock e Safety features when operating 3 MAINTAINING YOUR APPLIANCE 4 SPECIAL MESSAGES DIFFICULTIES 5 AFTER SALES SERVICE 11 11 14 15 16 17 We are constantly improving our products for this reason we reserve the right to make all modifications to their technical functional or aesthetic characteristics originating from tech nical developments Warning This product is not foreseen for sale in the USA Before installing and using your appliance please read this installation and use the guide carefully it will help you familiarise yourself very rapidly with its operation Ey 1 INSTALLING YOUR APPLIANCE ore Above a cabinet with a door or drawer CHOOSING THE POSITION The distance between the edge of your appliance B NN and the side and rear walls or partitions must be at Pas MIN 4mm gt least four centimetres zone A 0 0 Your appliance may be built in without any restric tion Check however that the air intake and outlet are free of obstruction The building in method opposite i
7. De Dietrich Dear valued customer To discover a De Dietrich product is to experience the range of unique emotions which only high value items can produce The attraction is immediate from the moment you set eyes on the product The sheer quality of the design shines through thanks to the timeless style and outstanding finishes which make each appliance an elegant and refined little masterpiece in its own right each in perfect harmony with the others Next comes the irresistible urge to touch it De Dietrich s design makes extensive use of robust and prestigious materials The accent is placed firmly upon authenticity By combining state of the art technology with top quality materials De Dietrich produces beautifully crafted products to help you get the most from the culinary arts a passion shared by all lovers of cooking and fine food We hope that you enjoy using this new appliance and we would love to receive your suggestions and to answer any questions you may have Please feel free to contact our customer service department via our website To benefit from the many advantages offered by the brand we recommend that you register your product at www de dietrich com Thank you for choosing a De Dietrich product De Dietrich You can find a full range of information about the brand at www de dietrich com Visit the De Dietrich Gallery 6 rue de la P pini re Paris eighth district Open from Tuesday to Saturday from 10 am to
8. I1117X 90 x 49 e Selector buttons Use these buttons to select turn on and turn off the cooking zones When a zone is selec ted you will see it light up and you can adjust its settings A front CONTINUUM zone B rear CONTINUUM zone C complete CONTINUUM zone D 28 cm zone E 23 cm zone F 16 cm zone For a selected zone Litt wer e ODDK Indicator for Power Timer display selected zone display e Adjustment buttons These buttons allow you to adjust power timer programmer for each of the selected zones H Boi function power preselection J recommended timer K ELAPSED Time function L locking unlocking Clean lock M Switcu function N power slider O timer slider If there is no cookware on the selected zone your adjustments will delete automatically after a few moments 10 2 USING YOUR APPLIANCE EN Using a cooking zone Adjusting the power level Place your cookware on the cooking zone and press the on off button for the zone to be used A beep and a light will confirm your selection Adjust the power by sliding your finger on the power slider to the right to increase and to the left to decrease the power or by using the preselected power settings Switching off a cooking zone Press your finger on the selector button Adjusting the timer Adjust the timer by sliding your finger on the timer slider to the right to increase and to the left to d
9. ammable objects or products in the kitchen furniture under neath your cooking hob WHAT TO DO Light Cleaning sponges Thoroughly moisten the zone to be cleaned with hot water then wipe off Accumulation of baked on stains dirt Sugar spills melted plas tics Cleaning sponges Scraper for glass Thoroughly moisten the zone to be cleaned with hot water Use a scraper for glass to remove the large bits follow with the rough side of a disinfectant sponge and then wipe off Rings and hard water residue White vinegar Apply warm white vinegar to the stain let stand then wipe with a soft cloth Shiny metal colourings Weekly maintenance ic glass product cleaning sponge special for delicate crockery Special vitroceram 15 Apply a cleaning agent for vitroceramic glass preferable one with silicon for its protective properties to the surface powder abrasive sponge Ey 4 SPECIAL MESSAGES DIFFICULTIES e On first use POSSIBLE CAUSES WHAT SHOULD YOU DO A special lamp appears Working normally Nothing the light disappears after 30 seconds Your installation blows a fuse Only one side works The electrical connection of your hob is incorrect Check that it is set up properly See the Electrical Connection section The hob produces an odour dur ing the first cooking sessions e On switching on YOU OBSERVE THAT
10. at the same time Do not use cast iron cookware Do not use a lid Do not use salt e Independent timer This function allows you to time an event without cooking Select a cooking zone you are not using Set the time with the timer slider A t flashes in the display At the end of your adjustment t becomes steady and the count begins N B You can stop a count in progress by keeping your finger on the button of the selection on the display g BRS e Elapsed time This function displays the time elapsed since the last time the power setting was adjusted on a given burner To use this function press the K button The elapsed time flashes on the timer display If you want cooking to end in a specific period press the K button then within 5 seconds slide your finger on the timer slider to increase the cooking time that you wish to set The time will display for 3 seconds then the remaining cooking time will appear A beep will confirm your choice This function can be used with or without the timer Note If a time is displayed on the timer it cannot be changed for 5 seconds after pressing the K button Once this period has elapsed you may change your cooking time e SWITCH This function lets you move a pan from one zone to another keeping the original settings power level and time 1 Press button M briefly A short beep sounds and you can move the pan to the new zone 2 Press
11. e top DTI1137X Overall dimensions L x DT1I1137X 65 x 51 3 Cut out Recess L x I DT1I1137X 56 x 49 De Dietrich e Selector buttons e Adjustment buttons Buttons A B and C are used to select cooking These buttons allow you to adjust power zones and turn them on and off When a zone timer programmer for each of the selected is selected you will see it light up and you can zones adjust its settings H Boi function power preselection For a selected zone Oo wr J recommended timer o H 2 O ODA K ELapsep Time function Indicator for Power Timer display L locking unlocking Clean lock selected zone display M Switcu function N power slider O timer slider If there is no cookware on the selected zone your adjustments will delete automatically after a few moments EN 2 USING YOUR APPLIANCE DTI1117X Overall dimensions L x DTI1117X 65 x 51 3 Cut out Recess L x I DT1I1117X 56 x 49 e Selector buttons e Adjustment buttons Buttons A B and C are used to select cooking These buttons allow you to adjust power zones and turn them on and off When a zone timer programmer for each of the selected is selected you will see it light up and you can zones adjust its settings H Bot function power preselection For a selected zone oOo nn J recommended timer e bebe O Libs moe K ELAPSED Time function Indicator fo
12. ecrease the time When the cooking is finished 0 is dis played and a beep sounds Press on the selector button for the zone to delete this information N B If you slide your finger on the timer slider from right to left you to reach directly 99 minutes If you do not make a selection or if there is no cookware the selected zone turns off after a few moments ADDITIONAL FUNCTIONS Boil function This function allows you to bring water to boiling point and keep it there for any food requiring cooking in boiling water Select a cooking zone Press button H briefly A short beep is heard 2I is displayed by default Adjust the volume of water by sliding your fin ger on the power slider from 0 5 litres to 6 litres The quantity of water can be 0 5l 11 1 5l 2l 2 51 3I 41 5I and 6 litres 11 Briefly press button H to confirm A short beep is heard and the boil display becomes fixed A series of beeps are heard when your water is at boiling point and the word boil scrolls across the display b followed by o etc Put the food in pasta rice etc Briefly press button H power level 12 or 13 and 8 min are displayed by default You can change the power and time using sliders N and O NB It is important that the water temperature is neither too hot nor too cold when cooking begins otherwise the final result will be affected This function can be used on all burners
13. ily domestic installation and use as set out in the user manual against manu facturing defects for the Warranty periods shown above 3 Should service be required under this Warranty the purchaser should contact an approved DE DIETRICH Service Provider during their normal business hours 4 At no time does DE DIETRICH have liability for any freight or transportation costs or for any damage during transit or for any conse quence of failure of this appliance outside of the normal service area unless such limita tion of liability is prohibited by statute 5 This Warranty excludes replacement of parts required due to normal wear and tear including light globes 6 This Warranty only applies provided the appliance has been used in accordance with the manufacturer s instructions and provided an accident misuse neglect or abuse has not damaged the appliance 7 None of the above Warranties purport to exclude restrict or modify either the applica tion or the exercise of a right conferred by any applicable Statute 8 Please complete the details below which should be retained for future reference along with your proof of purchase Date of Purchase cscceeseeeeeeees Model No Serial No Notice to Victorian Customers from the Victorian Plumbing Industry Commission This product must be installed by a licensed person as required by the Victorian Building Act 1993 Only a licensed person will give you a Compliance
14. ng of the hob conforms to current electromagnetic interference standards and thus is in total compliance with legal requirements 89 336 EEC directives In order to avoid interference between your cooking hob and a pacemaker your pacemaker must be designed and programmed in compliance with the regulations that apply to it As we can guarantee the compliance only of our own products we strongly recommend that you refer to the maker of your device or to your doctor to avoid possible incompatibilities 3 MAINTAINING YOUR APPLIANCE EN Preserve your appliance The vitroceramic glass surface is highly resistant but not unbreakable Here are some recommendations for increasing its lifetime Avoid banging or clattering the cookware Avoid putting heating covers on the hob A suction effect may damage the vitroceramic surface Do not use cookware with bottoms that are rough or dented Do not use your cooking hob as a work sur face Never use aluminium foil or paper or alu minium scrubber to clean it The aluminium melts and damages the top Never use a steam cleaner to clean your hob Maintaining your appliance TYPES OF STAINS SPOTS USE Never directly reheat a tin can It will have a risk of exploding Aesthetic faults as a result of mistreatment of your hob and which do not entail a lack of function are not covered by our guarantee And for the safety of your kitchen do not place cleaning items or infl
15. ottom of the cookware If you leave empty cookware on a zone which is turned on it will automatically limit the power in order to prevent damage to the cookware or hob Protection against overflows In case of overflow or of a metallic object or wet cloth placed on the control areas the hob turns itself off the displays light up and a beep sounds Clean the hob or remove the object then begin cooking again to electrical and electronic equipment waste Contact your local authority or retailer for how to have used appliances collected or collection points e Auto Stop system If you forget cooking is in progress after a predefined time this safety function will auto matically turn off your hob from 1 to 10 hours depending on the power setting AS dis plays and a beep sounds after about 2 min utes Press on the main selector to delete this information A beep will confirm your setting e Small Items safety If you place a small object on the area a ring a fork etc the hob will detect it and not deliv er any power The power display flashes Note However several small objects at the same time on a zone could be identified as cook ware In that case power will be delivered by the hob It is recommended that you avoid placing metal objects such as knives forks spoons and lids on the cooking sur face as they may become hot For users with heart pacemakers and active implants The functioni
16. r Power Timer display L locking unlocking Clean lock selected zone display M Switcu function N power slider O timer slider If there is no cookware on the selected zone your adjustments will delete automatically after a few moments 2 USING YOUR APPLIANCE DT11047GC DTI1167XE For DTI1167XE 3600 W For DTI1047GC 4600 W Overall dimensions L x DTI1047GC 65 x 51 DTI1167XE 78 2 x 50 7 Cut out Recess L x I DTI1047GC 56 x 49 DTI1167XE 75x49 6 e Selector buttons Use these buttons to select turn on and turn off the cooking zones When a zone is selec ted you will see it light up and you can adjust its settings A front CONTINUUM zone B rear Continuum zone C complete CONTINUUM zone E 16 cm zone F zone 23 cm For a selected zone Ooo aa e ODOR Indicator for Power Timer display selected zone display e Adjustment buttons These buttons allow you to adjust power timer programmer for each of the selected zones H Bol function power preselection J recommended timer K ELAPSED Time function L locking unlocking Clean lock M Switcu function N power slider O timer slider If there is no cookware on the selected zone your adjustments will delete automatically after a few moments EN 2 USING YOUR APPLIANCE DTI1177X Overall dimensions L x DTI1117X 93 x 51 Cut out Recess L x DT1
17. ring cooking This is normal with some types of cookware This is caused by the transfer of energy from the hob to the cookware Nothing There is no risk neither to your hob nor to your cookware The fan continues to function a few minutes after your hob is turned off Cooling of the electronic com ponents Working normally Nothing the fuses or turn off the circuit breaker for your hob to avoid the risk of electrical yN In case of breakage cracks or even light fissures in the vitroceramic glass take out shock Contact the After Sales Service Department 16 5 AFTER SALES SERVICE EN In the unlikely event of there being a problem with your appliances please call the number below quoting the model number of your appliance this can be found on the rating plate Our trained staff are available to advise or book a service call with one of our authorized service agents FagorBrandt SAS Management company SAS social capital of 20 000 000 euros RCS Nanterre 440 303 196 17 De Dietrich Distributed by MEA A Divisions of Hagemeyer Brands Australia FOR AUSTRALIAN CUSTOMERS ONLY PRODUCT WARRANTY STATEMENT OF STANDARD WARRANTY CONDITIONS 1 Subject to the Statement of Standard Warranty Conditions this product is covered by the following Warranty TWO 2 YEARS WARRANTY from date of purchase covering all parts and labour 2 The appliance is warranted under normal single fam
18. rport to exclude restrict or modify either the applica tion or the exercise of a right conferred by any applicable statute 7 Subject to any Warranties implied by sta tute at no time will MEA or its Service Providers be liable for any economic loss consequent upon the failure of the appliance 8 This Warranty is only valid for De Dietrich major appliances imported and distributed by MEA purchased and used in Australia CZ5701023 00 08 11
19. s recommended for use above an oven or a built in appliance BUILDING IN Follow the diagram above Glue the foam seal underneath your appliance follo wing the perimeter of the hole in the worktop upon which your appliance will rest This will ensure a good seal against the worktop Attach the clips to the hob depending on the model Above an oven eee ccccccccccccces Ti If jou hob is located above your oven the hob s thermal safety devices can impede the simultaneous use of the hob and the oven s pyrolysis program Your hob is equipped with an anti overheating safety system This safety device can trigger for example when the hob is installed over an oven that is not suf ficiently insulated If this occurs a series of small lines appears on the control panel In such cir cumstances we recommend hell you increase the hob s ventilation by creating an opening in the side of the cabinet 8 x 5 cm and or installing an oven insulation kit available from the after sales Ref 75X1652 You can also install your hob above a dishwasher In this case your worktop must be at least 900mm high in order to ensure proper ventilation to your hob and you could also fit the dishwasher insulation kit that is available from the After Sales Service Ref 7781 1 INSTALLING YOUR APPLIANCE EN Connection Your appliance should be positioned so that the mains switch is accessible These hobs must
20. ts up The indicator will go out automatically after a few moments To unlock Press button L until you hear a double beep and the indicator goes out N B In locked mode any action will produce a key symbol on the display You must unlock your hob before using it If you activate the lock while cooking the stop display will be prioritised on the lock e Clean lock This function allows you to temporarily lock your hob while cleaning To activate Clean Lock Your cooking hob must be turned off Press button L briefly you will hear a beep and the indicator will start flashing After a preset time the lock will automatically disengage A double beep sounds and the indicator goes out 13 2 USING YOUR APPLIANCE As shown in this logo the materials used to package this appliance are not recycla ble Recycle them and play a role in protecting the environment by depositing them in municipal containers provided for this purpose Recycling of the appliances organised by your manufacturer will thus be undertaken in optimum conditions in accordance with European directive 2002 96 CE relating Safety when operating e Residual heat After a long cooking period the zone used can remain hot for several minutes An H flashes during this period Do not put your hand on the zone Temperature limiter Each cooking zone is equipped with a safety sensor that constantly monitors the tempera ture of the b
Download Pdf Manuals
Related Search