H8S/2140B Series Expansion I/O Board (HS2140EIO61H
Contents
1. shall be defined as the following products produced only by Hitachi Ltd excluding all subsidiary products e E6000 series emulator station e Expansion I O board e User system interface cables e PC interface board The user system or a host computer is not included in this definition Purpose of the Expansion I O Board This expansion I O board is installed in the E6000 emulator and enables the emulator station to be connected to the user system interface cable This expansion I O board must only be used for the above purpose Improvement Policy Hitachi Ltd including its subsidiaries hereafter collectively referred to as Hitachi pursues a policy of continuing improvement in design functions performance and safety of the emulator product Hitachi reserves the right to change wholly or partially the specifications design user s manual and other documentation at any time without notice Target User of the Emulator Product This emulator product should only be used by those who have carefully read and thoroughly understood the information and restrictions contained in the user s manual Do not attempt to use the emulator product until you fully understand its mechanism It is highly recommended that first time users be instructed by users that are well versed in the operation of the emulator product RENESAS LIMITED WARRANTY Hitachi warrants its emulator products to be manufactured in accordance with published spe2. Board Screws Figure 1 2 Opening the Case of the Expansion I O Board To open the case of the expansion I O board remove the four screws on the cover To close the case place the cover on the expansion I O board and fix it with the four screws To prevent breaking of wires in the expansion I O board do not place heavy or sharp metal objects on the expansion I O board while the case is open RENESAS Section 2 Connection Procedures A WARNING Always switch OFF the user system and the emulator product before the EXPANSION I O BOARD or USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on each side is correctly aligned Failure to do so will result in a FIRE HAZARD and will damage the user system the emulator product the user system interface cable and the expansion I O board or will result in PERSONAL INJURY The USER PROGRAM will be LOST 2 1 Using Emulator without Connecting User System 1 Make sure the emulator is turned off 2 After making sure the direction of the expansion I O board connector labeled E6000 EMULATOR is correct firmly insert the expansion I O board connector into the emulator station connector When the emulator is operated while connected to only the expansion I O board without connecting the user system disconnect the cable body from the expansion I O board RENESAS 2 2 Using Emulator with Connecting User System
3. O board 2 Power is supplied from the emulator station to the expansion I O board 3 LPC Module and Ports C to G Reset Specifications For the reset function of the LPC module note that there are differences between the H8S 2140B series E6000 expansion I O board and the target MCU The reset conditions for the CPU and other modules than the LPC have no differences Internal Reset by Go RESET CPU Reset Signal Input of Reset Type WDT Overflow RESET Commands Target System E6000 expansion I O Reset enabled Reset disabled Reset enabled board Target MCU Reset enabled Reset enabled Note RESET signal from the target board to the evaluation chip can be masked by setting RESET MASK check box in Configuration window of HDI But reset signal for the LPC module are always enabled when RESET MASK in Configuration of the HDI is either enabled or disabled When user debugs target system with the expansion I O board disable RESET MASK and always input RESET signal from the target system RENESAS
4. license from the Japanese government and cannot be imported into a country other than the approved destination Any diversion or reexport contrary to the export control laws and regulations of Japan and or the country of destination is prohibited Please contact Renesas Technology Corporation for further details on these materials or the products contained therein ADE 702 310 Rev 1 0 04 08 02 Hitachi Ltd H8S 2140B Series Expansion I O Board HS2140EIO61H for E6000 Emulator User s Manual 2 CENESAS HS2140EIO61HE Cautions Hitachi neither warrants nor grants licenses of any rights of Hitachi s or any third party s patent copyright trademark or other intellectual property rights for information contained in this document Hitachi bears no responsibility for problems that may arise with third party s rights including intellectual property rights in connection with use of the information contained in this document Products and product specifications may be subject to change without notice Confirm that you have received the latest product standards or specifications before final design purchase or use Hitachi makes every attempt to ensure that its products are of high quality and reliability However contact Hitachi s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human
5. life or cause risk of bodily injury such as aerospace aeronautics nuclear power combustion control transportation traffic safety equipment or medical equipment for life support Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating operating supply voltage range heat radiation characteristics installation conditions and other characteristics Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges Even within the guaranteed ranges consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail safes so that the equipment incorporating Hitachi product does not cause bodily injury fire or other consequential damage due to operation of the Hitachi product This product is not designed to be radiation resistant No one is permitted to reproduce or duplicate in any form the whole or part of this document without written approval from Hitachi Contact Hitachi s sales office for any questions regarding this document or Hitachi semiconductor products IMPORTANT INFORMATION READ FIRST e READ this user s manual before using this emulator product e KEEP the user s manual handy for future reference Do not attempt to use the emulator product until you fully understand its mechanism Emulator Product Throughout this document the term emulator product
6. ESER EA Ea A ETSER 1 5 Opening the Case of expansion I O board cece cess ceeeecseceseeecsseceseesesseceseeeesaeenees Section 2 Connection Procedures 5 5 5 605 Seonssate ler ghas aaesnenseatabassnvey am tedgues duh Oaeange 2 1 Using Emulator without Connecting User System cccccceceesseeeeescseeceeeceeecneesneeeeeees 2 2 Using Emulator with Connecting User System through User System Interface Cable Section dS Us r Syst m Interface nessico ekg Secon A NOUE en a a a E A e a aT ii RENESAS Section 1 Overview The H8S 2140B series E6000 expansion I O board hereinafter referred to as the expansion I O board is an efficient software and hardware development support tool for application systems using Hitachi s original microcomputers H8S 2140B series LPC Low Pin Count interface The expansion I O board should be used with H8S 2148B series E6000 emulator station HS2140EPI61H hereinafter referred to as the emulator 1 1 Environment Conditions Table 1 1 Environment Conditions Item Specifications Temperature Operating 10 to 35 C Storage 10 to 50 C Humidity Operating 35 to 80 RH no condensation Storage 35 to 80 RH no condensation Ambient gases No corrosive gases Power supply Power supply from E6000 emulator station User system voltage UVcc Depends on the target MCU within the range 2 7 V to 3 6 V 1 2 Supported MCUs and User System Interface Cables Table 1 2 shows the correspondence bet
7. To all our customers Regarding the change of names mentioned in the document such as Hitachi Electric and Hitachi XX to Renesas Technology Corp The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas Technology Corporation on April 1st 2003 These operations include microcomputer logic analog and discrete devices and memory chips other than DRAMs flash memory SRAMs etc Accordingly although Hitachi Hitachi Ltd Hitachi Semiconductors and other Hitachi brand names are mentioned in the document these names have in fact all been changed to Renesas Technology Corp Thank you for your understanding Except for our corporate trademark logo and corporate statement no changes whatsoever have been made to the contents of the document and these changes do not constitute any alteration to the contents of the document itself Renesas Technology Home Page http www renesas com Renesas Technology Corp Customer Support Dept April 1 2003 7tENESAS Renesas Technology Corp Cautions Keep safety first in your circuit designs 1 Renesas Technology Corporation puts the maximum effort into making semiconductor products better and more reliable but there is always the possibility that trouble may occur with them Trouble with semiconductors may lead to personal injury fire or property damage Remember to give due consideration to safety when making your circuit designs with appropriate me
8. asures such as 1 placement of substitutive auxiliary circuits ii use of nonflammable material or iii prevention against any malfunction or mishap Notes regarding these materials 1 These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corporation product best suited to the customer s application they do not convey any license under any intellectual property rights or any other rights belonging to Renesas Technology Corporation or a third party Renesas Technology Corporation assumes no responsibility for any damage or infringement of any third party s rights originating in the use of any product data diagrams charts programs algorithms or circuit application examples contained in these materials All information contained in these materials including product data diagrams charts programs and algorithms represents information on products at the time of publication of these materials and are subject to change by Renesas Technology Corporation without notice due to product improvements or other reasons Itis therefore recommended that customers contact Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor for the latest product information before purchasing a product listed herein The information described here may contain technical inaccuracies or typographical errors Renesas Technology Corporation assumes no respo
9. cifications and free from defects in material and or workmanship Hitachi at its option will repair or replace any emulator products returned intact to the factory transportation charges prepaid which Hitachi upon inspection determine to be defective in material and or workmanship The foregoing shall constitute the sole remedy for any breach of Hitachi s warranty See the Hitachi warranty booklet for details on the warranty period This warranty extends only to you the original Purchaser It is not transferable to anyone who subsequently purchases the emulator product from you Hitachi is not liable for any claim made by a third party or made by you for a third party DISCLAIMER HITACHI MAKES NO WARRANTIES EITHER EXPRESS OR IMPLIED ORAL OR WRITTEN EXCEPT AS PROVIDED HEREIN INCLUDING WITHOUT LIMITATION THEREOF WARRANTIES AS TO MARKETABILITY MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR USE OR AGAINST INFRINGEMENT OF ANY PATENT IN NO EVENT SHALL HITACHI BE LIABLE FOR ANY DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE EMULATOR PRODUCT THE USE OF ANY EMULATOR PRODUCT OR ITS DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS WARRANTY THIS EMULATOR PRODUCT IS SOLD AS IS AND YOU MUST ASSUME ALL RISK FOR THE USE AND RESULTS OBTAINED FROM THE EMULATOR PRODUCT RENESAS State Law Some state
10. different from your actual system Limited Anticipation of Danger Hitachi cannot anticipate every possible circumstance that might involve a potential hazard The warnings in this user s manual and on the emulator product are therefore not all inclusive Therefore you must use the emulator product safely at your own risk III RENESAS SAFETY PAGE READ FIRST e READ this user s manual before using this emulator product e KEEP the user s manual handy for future reference Do not attempt to use the emulator product until you fully understand its mechanism DEFINITION OF SIGNAL WORDS A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE emphasizes essential information lt RENESAS AWARNING Observe the precautions listed below Failure to do so will r
11. esult in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance 2 Always switch OFF the E6000 emulator and user system before connecting or disconnecting any CABLES or PARTS 3 Always before connecting any CABLES make sure that pin 1 on both sides are correctly aligned 4 Supply power according to the power specifications and do not apply an incorrect power voltage Use only the provided power cable RENESAS Preface Thank you for purchasing this H8S 2140B series expansion I O board HS2140EIO61H hereinafter referred to as the expansion I O board for the H8S series E6000 emulator The expansion I O board enables user systems for Hitachi s original microcomputer H8S 2140B series to be developed using an H8S 2148B series E6000 emulator HS2140EPI61H hereinafter referred to as the emulator RENESAS Contents Section L lt OWVERVIOW on inta e A E EA EAT A A EA AAA EI Environment Conditions sins cciscacsesc stscstavevces iee e e de esae aee a SKEN ES 1 2 Supported MCUs and User System Interface Cables ssnesssesssesessssseessesserssesssrsessseessee 1 3 Operating Voltage and Frequency Specifications sssessesssessseseseseseessresseessrssersesereesee L COMPONENIS ea aeaa a A E E soyshnods ds EE aaO EEEE eaa
12. nsibility for any damage liability or other loss rising from these inaccuracies or errors Please also pay attention to information published by Renesas Technology Corporation by various means including the Renesas Technology Corporation Semiconductor home page http www renesas com When using any or all of the information contained in these materials including product data diagrams charts programs and algorithms please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products Renesas Technology Corporation assumes no responsibility for any damage liability or other loss resulting from the information contained herein Renesas Technology Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake Please contact Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor when considering the use of a product contained herein for any specific purposes such as apparatus or systems for transportation vehicular medical aerospace nuclear or undersea repeater use The prior written approval of Renesas Technology Corporation is necessary to reprint or reproduce in whole or in part these materials If these products or technologies are subject to the Japanese export control restrictions they must be exported under a
13. ort 83 Note Pin sockets are mounted on the expansion I O board so that resistors can be mounted on R1 to R16 by the user Resistors are not mounted on R1 to R16 at shipment Resistors can be mounted on R1 to R16 by the user RENESAS CAUTION SW6 has a different circuit structure compared to other switches Side 3 When using WUEN7 as an IRQ7 interrupt set SW6 to side 3 In this case be aware that the PA1 pin function cannot be used Side 1 PA1 pin function can be used In the case be aware that WUEN7 cannot be used as an IRQ interrupt RENESAS Figure 3 2 shows location of switches and resistor Switch pin number r eA swas Jswe6 E6000 EMULATOR USER INTERFACE CABLE r 5 02 mm Resistor size of R1 to R16 Figure 3 2 Location of Switches and Resistor 10 RENESAS Section 4 Notice A WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 This expansion I O board is specifically designed for the HS2140EPI61H Do not use this expansion I O board with any other emulator station Use the H8S 2148 2140B series user system interface cable HS2148ECH61H for FP 100B or TFP 100B Do notuse any other series of user system interface cable 1 Do not place heavy objects on the expansion I
14. s do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which may vary from state to state The Warranty is Void in the Following Cases Hitachi shall have no liability or legal responsibility for any problems caused by misuse abuse misapplication neglect improper handling installation repair or modifications of the emulator product without Hitachi s prior written consent or any problems caused by the user system All Rights Reserved This user s manual and emulator product are copyrighted and all rights are reserved by Hitachi No part of this user s manual all or part may be reproduced or duplicated in any form in hard copy or machine readable form by any means available without Hitachi s prior written consent Other Important Things to Keep in Mind 1 Circuitry and other examples described herein are meant merely to indicate the characteristics and performance of Hitachi s semiconductor products Hitachi assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein 2 No license is granted by implication or otherwise under any patents or other rights of any third party or Hitachi Figures Some figures in this user s manual may show items
15. through User System Interface Cable CAUTION When connecting or removing the user system interface cable apply force only in the direction suitable for connection or removal while making sure not to bend or twist the cable or connectors Otherwise the cables or connectors will be damaged 1 Make sure the emulator and the user system are turned off 2 1 After making sure the direction of the expansion I O board connector labeled E6000 EMULATOR is correct firmly insert the expansion I O board connector into the emulator station connector 1 in figure 2 1 2 To connect the expansion I O board labeled USER INTERFACE CABLE and the user system interface cable body Emulator station Figure 2 1 Connecting Expansion I O Board to Emulator Station and User System Interface Cable RENESAS Section 3 User System Interface Switches protection circuit and termination circuits are provided for the H8S 2140B LPC interface of the expansion I O board Signals are connected to the user system interface cable with the protection circuit Figure 3 1 shows user interface circuit E6000 HS2140EPI61H HS2140EI061H H8S 2140B H8S 2140B ZN Evaluation chip RB Protection circuits Rc D1 and D2 User system Termination circuits Ra and RB interface cable Figure 3 1 User System Interface Circuit Table 3 1 shows switches and circuit description RENESAS Table 3 1 User System Interface Descrip
16. tion Termination Termination No Signals Switch circuit R circuit R R D D Notes 1 LADO SW7 side 3 Pull up R1 Pull down R2 R is 47kohm SW7 side 1 is port 30 2 LADI SW8 side3 Pull up R3 Pull down R4 Mustnotbe swe side 1 is port 31 removed 3 LAD2 SW9 side 3 Pull up R5 Pull down R6 SW9 side 1 is port 32 i 7 Pull R W10 side 1 i 4 LAD3 SW10 side 3 Pull up R7 ull down R8 D and D are SW10 side 1 is port 33 5 LFRAMEN SW11 side3 Pull up R9 Pull down not connected SW11 side 1 is port 34 R10 6 LRESETN SW12side3 Pull up R11 Pull down SW12 side 1 is port 35 R12 7 LCLK SW13 side 3 Pull up R13 Pull down SW13 side 1 is port 36 R14 8 SERIRQ SW14 side3 Pull up R15 Pull down SW14 side 1 is port 37 R16 9 WUENO SW15 side3 None None R is not SW15 side 1 is port BO 10 WUEN1 SW16 side 3 conngetgd SW16 side 1 is port B1 11 WUEN2 SW17 side 3 SW17 side 1 is port B2 12 WUEN3S SW18 side 3 D and D are sw 18 side 1 is port B3 connected 13 WUEN4 SW19 side 3 must not be SW19 side 1 is port B4 14 WUEN5S SW20 side 3 removed SW20 side 1 is port B5 15 WUEN6 SW21 side 3 SW21 side 1 is port B6 16 WUEN7 SW22 side 3 SW22 side 1 is port B7 17 PMEN SW23 side 3 SW23 side 1 is port 80 18 GA20 SW24 side 3 SW24 side 1 is port 81 19 CLKRUNN SW25 side 3 SW25 side 1 is port 82 20 LPCPDN SW26 side 3 SW26 side 1 is p
17. ween the MCUs and the user system interface cables supported by the E6000 H8S 2140B Series Table 1 2 H8S 2140B Series MCUs and User System Interface Cable MCU Type No Number Package E6000 User System Interface Cables 1 HD64F2140B 100 pin QFP FP 100B HS2148ECH61H HD64F2141B 100 pin TQFP TFP 100B HD64F2145BV RENESAS 1 3 Operating Voltage and Frequency Specifications Table 1 3 shows an example of the MCU operating voltage and frequency specifications supported by the E6000 If the E6000 is used in an environment that exceeds the operating voltage range and operating frequency range guaranteed for the MCU operation normal emulator operation is not guaranteed Table 1 3 Operating Voltage and Frequency Specifications Operating Frequency No MCU Types Operating Voltage V b MHz 1 H8S 2140B series 2 7 3 6 2 10 NOTE For details on the operating voltage and frequency specifications refer to the MCU hardware manual RENESAS 1 4 Components Figure 1 1 shows the HS2140EIO61H expansion I O board appearance and table 1 4 lists the components of the expansion I O board Please make sure you have all of these components when unpacking Figure 1 1 HS2140EIO61H Expansion I O Board Table 1 4 HS2140EIO061H Components No Component Quantity Remarks 1 HS2140EIO61H 1 Expansion I O board 2 Documentation 1 User s manual for HS2140EIO61H this manual RENESAS 1 5 Opening the Case of Expansion I O
Download Pdf Manuals
Related Search