Operators Manual
Contents
1. 19 User Preparation 21 Tire PETE Ju 21 Weight Addition ee eee 22 Dirt Shield Kit Optional 23 3 Operation ee 25 Important Information 26 SPECO ER 26 Planting LMES weerstand 26 Ground Density Z dad cozni s 26 TransportatiOn annen 27 Machine Operation 28 PANES EE 28 Lower Hitch Points 28 Upper Hitch Points 28 Attach to Tractor 30 Adjust Height 30 Operate Machine 31 MAN120 Introduction 4 Adjustments Weight Addition sese Ile let Ate A TE E erai Tre E Rotor Distance from Pulling Wheels Adjust the Rotor sese Chain Tension Change Row Width 5 Maintenance enen eneen Vue Te Aae Gearboxes eese Change OH aitia ner Chek Ollanta ETC eae EE LUDIC gt mitta as UDNES vs Rotor Bearings MAN120 Hi Speed Cotton Stalk Puller Chopper CUCA ricino imo rendo 48 Blade e E 49 Lubrication Gchedule 50 End of Season Storage 51 Remove Wheels 91 Prepare Tanks 51 General Cleaning eee eee 522. MAN120 Adjustments Chain Tension Both upper and lower chains should have between 1 2 to 1 of movement in the slack side of the chain If there is more slack than the recommended 1 2 to 1 adjust the tensioner until there is the correct amount of slack To access the upper chain remove the left hand shield Tensioner MAN120 40 Hi Speed Cotton Stalk Puller Chopper To access the lower chain remove the smaller shield The lower chain tensioner is shown below Tensioner 4 WARNING Replace all shields before operating your machine 5 29 2015 Hi Speed Cotton Stalk Puller Chopper Adjustments Change Row Width Before beginning this procedure be sure to have the correct length input shaft If not order the appropriately sized shaft from the dealer specifying the row width you want to change the Cotton Stalk Puller to 36 38 or 40 for the SPC 4 or 36 or 38 for the SPC 6 Refer to the Parts Catalog for the part number of the shaft needed 1 Remove upper shield LES 4 Measure distance from frame edge to pay Remove upper shield RSS inside edge of sprocket top photo NE Measure distance between Moo BS ps E vn 5 Remove sprocket 4 WARNING Replace all shields before operating your machine 3 Remove the upper chain 5 29 2015 41 MAN120 Adjustments Hi Speed Cotton Stalk Puller Chopper Change Row Width 10 Remove the clutch assembly middle 6 Remove bea
3. Safety Hi Speed Cotton Stalk Puller Chopper NOTE This section covers general safety Some items may not apply to this type of machine Handle Chemical Products Safely e Direct exposure to hazardous chemicals can cause serious injury Potentially hazardous chemicals used with AMADAS eguipment include such items as lubricants coolants paints and adhesives Before you start any job using a hazardous chemical check the MSDS so that you are aware of the risks and know how to proceed safely Carefully follow all procedures using only recommended equipment See your AMADAS dealer for MSDS on chemical products used with AMADAS equipment Practice Safe Maintenance Understand the service procedure before doing work Use proper tools and refer to the User Manual Keep service area clean and dry Lower machine to ground engage parking brake turn off engine and remove key before performing maintenance Allow time for the machine to cool completely Never lubricate service or adjust machine while it is moving Keep hands feet and clothing from power driven parts Securely support any machine elements that must be raised for service work 6 06 03 15 Avoid Contact with Moving Parts Wear close fitting clothing to avoid entanglement with moving parts Keep hands feet and clothing away from power driven parts Never clean lubricate or adjust machine when it is running e AAA Remove
4. Adjustments Hi Speed Cotton Stalk Puller Chopper Tire Pressure Generally 26 32 PSI is reguired to hold the stalks and prevent them from slipping In softer soil and with shorter cotton less pressure is reguired than in harder soil and with taller cotton NOTE Do NOT exceed 32 PSI for the tires If 32 PSI is not enough air pressure for pulling stalks you will need to wait until soil conditions change e g it rains and the soil softens While you may need to wait for the soil to soften wet stalks are more difficult for the machine to remove Early morning dew rain or other wet conditions can cause the stalks to slip in the tires and we recommend that you not try to pull and chop stalks while they are wet As a starting point inflate tire pressure to 26 PSI Increase tire pressure as needed until the machine is pulling stalks Operating with a lower tire pressure will make the machine easier to pull through the field We recommend operating at the lowest tire pressure needed to do the job MAN120 36 5 29 2015 Hi Speed Cotton Stalk Puller Chopper Rotor Distance from Pulling Wheels For average stalks and soil conditions the factory setting should be satisfactory to completely pull and chop the stalks If the stalks are not being pulled and chopped however you may need to change the distance between the rotor and the pulling wheels Generally the longer the root the further back the rotor needs to be
5. 6 Troubleshooting 53 Warranty Statement 06 03 15 Hi Speed Cotton Stalk Puller Chopper AMADA fe Introduction Welcome Amadas Industries With origins dating back to 1963 Amadas Industries and its predecessors have a long history of providing high quality reliable innovative equipment for the farming industry Amadas equipment is currently at work throughout the United States and in many other countries This equipment includes machinery such as the Magnum Fource Peanut Combine Reel Rain Traveler Irrigation System Tree Bark Processing and Packaging Machinery and the Hi Speed Cotton Stalk Puller Chopper MAN120 Introduction Hi Speed Cotton Stalk Puller Chopper Congratulations on your purchase of the AMADAS Hi Speed Cotton Stalk Puller Chopper SPC The SPC is a patented uniquely integrated system used for extracting and chopping up cotton stalks and their roots This system provides you with a significant advantage over conventional mowing and discing The SPC removes each stalk s entire root system effectively breaking up the life cycle of insects and diseases that MAN120 iv Hi Speed Cotton Stalk Puller Chopper overwinter in the remaining stalk and root usually left behind by shredders and mowers The effectiveness of the SPC lies in the two part system that is incorporated into a single machine The tandem shaft mounted heavy duty tu
6. Beginning of Use a standard multi season purpose grease Every 50 hours Grease End of season points after cleaning Clutch Lubricate ooints Beginning of Use a standard multi season purpose grease Daily every 10 hours Anytime the ratchet clutch has been activated for extended periods End of season after cleaning Chains Lubricate Beginning of Use a standard 30 season weight oil Every 50 hours End of season after cleaning 6 3 2015 47 MAN120 Maintenance Hi Speed Cotton Stalk Puller Chopper Rotor Bearings Lubricate 2 grease points Beginning of Use a standard multi season purpose grease Every 50 hours End of season after cleaning MAN 683 2015 Hi Speed Cotton Stalk Puller Chopper Blades Typically blades need to be replaced every 500 1000 acres Ground conditions will also affect the life of the blades New blades are shown in the photo Generally replace blades when e the cutting edge is paper thin and or e the cutting edge begins to curl or bend 6 3 2015 49 Maintenance MAN120 Maintenance Hi Speed Cotton Stalk Puller Chopper Lubrication Schedule Location Type of Lubricant Beginning of End of Season Season PTO Shafts Multi purpose grease Double Universals Multi purpose grease Every 50 hours Every 50 hours Clutch Multi purpose grease ENE MAN120 50 6 3 2015 Hi Speed Cotton Stalk Puller Chopper End of Season Storage Remove Wheels Defl
7. IF if zl 20 6 3 15 MAN120 Hi Speed Cotton Stalk Puller Chopper Preparation User Preparation Tire Pressure Generally 26 32 PSI is reguired to hold stalks and prevent them from slipping through the wheels In softer soil and with shorter cotton less pressure is required than in harder soil and with taller cotton 1 As a starting point inflate tire pressure to 26 PSI NOTE Do not exceed 32 PSI for the tires If 32 PSI is not enough air pressure for pulling stalks you will need to wait until soil conditions change e g it rains and the soil softens While you may need to wait for the soil to soften wet stalks are more difficult for the machine to remove Early morning dew rain or other wet conditions can cause the stalks to slip in the tires and we recommend that you not try to pull and chop stalks while they are wet Increase the tire pressure until the machine is pulling stalks out of the ground Wu Operating with a lower tire pressure will AC ien i make the machine easier to pull through HEEL the field We recommend operating at the lowest tire pressure needed to do the job MAN120 6 3 15 21 Preparation Weight Addition The additional amount of weight required to chop the stalks depends on the type of soil soil hardness and the size of the cotton stalks We recommend starting with the rotor filled and the upper tank empty unless you are working with very hard and o
8. according to local regulations To increase visibility use the lights and devices provided with your machine Keep safety items in good condition Replace missing or damaged items Safety Hi Speed Cotton Stalk Puller Chopper Additional Safety for this Machine When operating this machine e Do NOT climb or ride on this machine at any time Do NOT let anyone stand between the machine and the tractor Make sure that everyone is clear of the machine prior to and during operation Keep all shields in place Keep all fingers feet and loose clothing away from moving parts Do NOT make adjustments or attempt any maintenance while the machine is in operation When working on this machine e Periodically check all nuts and bolts for tightness Make sure the SPC is supported using its storage legs even when the machine is attached to the tractor Use extreme caution when changing and handling blades New blades are extremely sharp and even used blades can cut if handled incorrectly 10 06 03 15 MAN120 Hi Speed Cotton Stalk Puller Chopper Safety Safety Decals M For replacement decals call your Safety decals identify specific hazards as well AMADAS dealer as general safety A signal word A DANGER AWARNING or ACAUTION is included on Replacement safety decals are available each decal to alert you to the severity of the free of charge hazard Safety decals used on this machine are shown
9. and visually inspect the tension of the chain The chain should have 1 2 to 1 play or movement in the slack side K GNE du IESU EP LJ Lr lt HER 7 3 F a E Remove shield d PE de C MAN120 6 3 15 17 Preparation Hi Speed Cotton Stalk Puller Chopper Install Blades 1 Determine if the blades are to be installed for 36 38 or 40 rows for the SPC 4 top and middle photo or 36 or 38 rows for the SPC 6 4 Install bolts from the flat side of the blades and torque to 90 ft Ibs A WARNING Use caution when tightening the bolts The edges of the blades are sharp and if your hand slips while tightening you can seriously cut yourself To verify that the blades are in the correct holes make sure the center of each blade is lined up with the compressed portion of the tires Refer to the drawings on the following page for blade positions 2 Determine which bolt holes to use for the correct row width Install the blades with the flat side pointing toward the tires The blade cuts and sharpens itself better with the flat side leading In the following photo blades are installed for 40 rows 18 6 3 15 MAN120 Hi Speed Cotton Stalk Puller Chopper Preparation Blade Positions 36 row ZZA 38 row nem le ale e cole of J Eisis p ei i MAN120 6 3 15 Preparation Hi Speed Cotton Stalk Puller Chopper Blade Positions 40 row SPC 4 only A RT AAA A nn AAA u
10. from the pulling wheels Instructions for moving the rotor are on the following page move the rotor towards the tractor move the rotor away from the tractor stalks are flying over the rotor and not being chopped the stalks are being chopped before they are completely oulled Additionally check your stalks by examining the root If the information on this page does not solve the problem refer to Chapter 6 Troubleshooting it is slipping through the pulling wheels is breaking off or completely missing the wheels it is starting to pull but the blade is catching the stem before it is extracted from the ground Or the stalk could be slipping through the wheels slightly Another possibility is that the tires have worn to the point that they no longer have sufficient grip the root is tight in the ground but chopped the root is in place facing down but loose in the soil 5 29 2015 Adjustments Right side Toward tractor Away from tractor AN Replace machine shields before operating 37 MAN120 Adjustments Hi Speed Cotton Stalk Puller Chopper Adjust the Rotor 4 CAUTION Take extreme caution when you change the rotor position Due to the weight of the machine this procedure must be done with the tractor attached to the Stalk Puller Chopper Two people are reguired to perform this adjustment 1 Remove the shield covering lower chain 2 Loosenthe idler and push
11. n wes J to the photos on the next page for hitch point y L a m positioning Lower Hitch Points There is a narrow end and a wide end on each of the pins for the two lower hitch points Use B these pins as follows Use lower link CAT III Hitch AREN A 4 w end of the pin CAT IVN Hitch b fo sl d 1 RA gt T x p E at H E un E e vodi ba V s ex Po cet d B 3 me c K d NON Ka F E es i KY a N L KL Es ag p ue 4 STA F S CA GG Kn A C AA S K E M m A SE ic vs e Pai ER A 0 VR Cm AX b Ze A A To gt MS ad N e e D K x B R X E CCS o a Meu Lo Far 22 Use A ur I FU Y t SV UE X IMS k 1 V ps Y ns TU d EN ig JE i en EE Piva SE i o Le E K AER e i q AA gt A dx e i Sit Ge PS E C La A 1 b 4 EA L Kx CA P ua d bat E AA R Poos d L MAN120 ga 529 2015 Hi Speed Cotton Stalk Puller Chopper Operation CAT III Hitch Use lower link d 3 D gt SKI e e a ba A n a an a i DAS em CAT IVN Hitch gt La p i x i p E ns adi A z d L L ee a Use the wider ends of the pins TT NSG 1 C eI er i PG OR ER SCH K aS M er Pie SS TD e n ZN Bees we SEH gd y P As Pa 25 er y A M i pn v SI sek Ue ss eil et A CC eale 38 jis ko NL r 1 N Ne Mas e Gm P a y gt pnt gt PAS 5 w Pr z et Fv s c ST d Y
12. new machine this procedure takes approximately four man hours to complete Allow several additional man hours for changing the row width on a used machine 16 6 3 15 Hi Speed Cotton Stalk Puller Chopper Different Model Numbers This manual covers Hi Speed Cotton Stalk Puller Choppers manufactured under model numbers CSP01 4 CSP02 4 SPC 4 SPC 6 Minor differences exist between the various models with regard to safety shielding n addition the SPC 6 contains six rotors rather than four as on the other three models While the SPC 4 is the model used in most of the pictures and sketches in this manual the information and instructions apply to all models If you have a CSP01 or CSPO2 please refer to your parts catalog for information on the safety shields specific to your model MAN120 Hi Speed Cotton Stalk Puller Chopper Preparation Dealer Preparation Initial Ins pection 4 Remove the lower shield and inspect the Upon receiving the Hi Speed Cotton Stalk lower chain The chain should have 1 2 Puller Chopper perform the following to 1 play or movement in the slack side inspection 1 Examine the machine for transport damage f the machine is damaged in Remove any way contact Amadas Industries at shield once Open the top covers and visually inspect all gearboxes for oil leaks A WARNING Replace shields Never operate machine without shields Remove the left side shield facing machine
13. off loading conveyor etc AVOID all lines particularly low hanging electrical cables during transport ADANGER Contact with electrical lines will cause the operator to suffer severe electrical shock or possibly death 06 03 15 Use following tow load weight ratios as guidelines 20 MPH when weight is less than or equal to the weight of the tractor 10 MPH when weight is more than weight of the tractor NEVER tow a load more than double the weight of the tractor Sudden braking can cause a towed load to swerve and upset Reduce speed if towed load is not equipped with brakes Use a Safety Chain e Use a safety chain to help control machinery if it separates from the tractor drawbar Use a chain with strength rating equal to greater than the gross weight of the towed machine Attach the chain to the tractor drawbar support allowing only enough slack in the chain for turning Do NOT use a safety chain for towing Safety Hi Speed Cotton Stalk Puller Chopper NOTE This section covers general safety Some items may not apply to this type of machine Avoid High Pressure Fluids A CAUTION Use extreme care when working with hydraulic components and high pressure sprays Escaping fluid or spray under pressure can penetrate the skin causing serious injury To avoid injury relieve pressure before disconnecting hydraulic or other lines Tighten all connections before applying hydraulic or spra
14. the tires above the recommended pressure Never weld or heat a wheel and tire assembly The heat can cause an increase in air pressure resulting in a tire explosion Welding can structurally weaken or deform the wheel Pay Close Attention to Notes e Throughout the manual information that needs to be emphasized is set apart with either a NOTE or IMPORTANT heading Please be sure to carefully read this information as it usually indicates a situation that could cause machine Maintain Your Machine e Itis crucial you maintain your machine in proper working condition Perform all scheduled maintenance and repairs in a timely manner Do NOT perform unauthorized modifications to the machine as these could impair the function and or safety of the machine and affect machine life MAN120 06 03 15 When inflating the tires use a clip on chuck and extension hose long enough to allow you to stand to one side and NOT in front of over the tire assembly Use a safety cage if available Check wheels for low pressure cuts bubbles damaged rims or missing lug bolts and nuts NEVER fill a damaged tire or one that is missing lug bolts or nuts Use Safety Lights and Devices Slow moving tractors self propelled equipment and towed implements or attachments can create hazards when driven on public roads They are difficult to see especially at night Whenever you drive on public roads use flashing lights and turn signals
15. 03 15 MAN120 Hi Speed Cotton Stalk Puller Chopper 2 MAN120 Preparation 6 3 15 Preparation OV ENV I CW ene 16 Set Row Wich 16 Different Model Numbers 16 Dealer Preparation eee eee 17 Initial Inspection evene 17 Install Blades nj iS 18 Blade Positions 19 User Preparation 21 Tire Pressure ee ee eee 21 Weight AQUI stenen iio 22 Dirt Shield Kit Optional 23 Preparation Overview Your Hi Speed Cotton Stalk Puller Chopper has been carefully prepared prior to being shipped Additional preparation is reguired however before the machine is ready for use Some of this preparation is usually performed by the dealer the rest will need to be done by you the user Please follow the instructions in this chapter to inspect your SPC and prepare it for use Information in this chapter is intended to prepare your SPC for general use Chapter 4 Adjustments provides suggestions for adjusting the machine to meet your specific farming needs Set Row Width Amadas Hi Speed Cotton Stalk Puller Choppers are delivered from the factory pre set The SPC 4 is set for 36 38 or 40 rows the SPC 6 is set for 36 or 38 rows When you order a machine you specify the desired row width If the row width of machine needs to be changed refer to Chapter 4 Adjustments for specific instructions On a
16. 1 CN S Fa Wie ES cA y En a ww e d t Ae E mr w z gel y 4 n es ES rah x BC x A i de si e AA A m t a AA a ES A SE e eir Ke 295 29 2015 29 MAN120 Operation Hi Speed Cotton Stalk Puller Chopper Attach to Tractor 1 Place the pin for the top link in the upper Pi hole Back the tractor up to the machine and lift it with the quick hitch M 0 Secure the latches on the quick hitch Lift machine slightly following safe lifting ls procedures 3 Remove the pin s on the support legs raise them all the way and replace the pin s Adjust Height Adjust the top link of the three point hitch so that the frame of the machine is parallel to the ground The angle of the machine to the ground affects its performance See Chapter 4 Adjustments under Inclination for more information on machine angle MAN120 30 5 29 2015 Hi Speed Cotton Stalk Puller Chopper Operation Operate Machine IMPORTANT To make sure you are using your Cotton Stalk Puller Chopper properly and effectively read the Important Information section at the beginning of this chapter before operating the machine 1 Lower the machine Make the turn and lower the machine again 2 Go forward accelerating as fast as possible The machine is more effective at high speeds The sooner the machine is moving quickly the more efficiently it works Lift the machine to turn If a turn is made with the ro
17. 2 62 54 64 7 o vi 06 03 15 uller Chopper Hi Speed Cotton Stalk P Dimensions SPC 4 3 15 06 0 Introduction Hi Speed Cotton Stalk Puller Chopper SPC 4 mm e e eer DEEN 5 E ATT L PE ee Qus n 13 3 SPC 6 a E Me o his SSS a nn SI 7 MAN120 viii 06 03 15 Hi Speed Cotton Stalk Puller Chopper Safety 1 Safety Safety at All Times 2 SAN P san 3 Additional Safety for this Machine 10 Safety Decals annen 11 This symbol means ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED MAN120 06 03 15 1 Safety Safety at All Times You the operator can help avoid accidents or injury by observing the precautions in this section and insisting that others working for or with you also follow them e Do NOT attempt to operate this equipment under the influence of drugs or alcohol or prescription over the counter drugs that may cause impairment This equipment is dangerous to children and persons unfamiliar with its operation They should never be allowed to operate this machinery or remain in its vicinity while in operation Only a trained operator familiar with this machinery and trained in its operation should be allowed to operate this machine Do NOT allow any person to operate or perform maintenance on this machine until he or she has read this manual and understands the safet
18. Accumulated Crop Debris e The buildup of chaff and crop debris near moving parts or heat sources is a hazard Check and clean these areas frequently Before performing any inspection or service engage parking brake turn off engine and remove key Keep all parts in good condition and properly installed Fix any damage immediately replace worn or broken parts Keep the machine free of any buildup of grease oil or debris MAN120 Hi Speed Cotton Stalk Puller Chopper Safety NOTE This section covers general safety Some items may not apply to this type of machine Remove Paint Protective Coating Before Welding Or Heating e Avoid potentially toxic fumes and dust e Hazardous fumes can be generated when paint or coatings are heated by welding soldering or by using a torch Do all work outside or in a well ventilated area Remove paint coatings before welding or heating o If you sand or grind paint avoid breathing the dust Wear an approved respirator If you use solvent or paint stripper remove stripper with soap and water before welding Remove solvent or paint stripper containers and other flammable material from the area Avoid Using Heat Near Pressurized Fluid Lines e Flammable spray can be generated by heating near pressurized fluid lines resulting in severe burns to yourself and bystanders Do NOT heat by welding soldering or using a torch near pressurized fluid lines or ot
19. Hi Speed Cotton Stalk Puller Chopper SPC 4 SPC 6 2nd Edition Beg S N 530000 AMADA fe Read this manual before using this product Failure to follow the instructions MAN120 June 2011 2011 and safety precautions in this manual can result in serious injury or death Updated June 2015 Hi Speed Cotton Stalk Puller Choppers are manufactured by Amadas Industries You can find us on the Web at www amadas com or e mail us at amadas amadas com You can also contact us at P O Box 1833 Suffolk VA 23439 P O Box 3687 Albany GA 31701 mailing mailing 1100 Holland Road Suffolk VA 23434 1701 South Slappey Blvd Albany GA 31706 shipping shipping 757 539 0231 phone 229 439 2217 phone 757 934 3264 FAX 229 439 9343 FAX Hi Speed Cotton Stalk Puller Chopper Table of Contents 06 03 15 Introduction Welcome eran eenden li Specifications vi Dimensions vii A a 1 Safety at All Times 2 Safety Practices 3 Additional Safety for this Machine 10 Sale PEAS 11 2 Preparations ce onu ose ore geess 15 OU 16 Set Row Width Gann 16 Different Model Numbers 16 Dealer Preparation 17 Initial Inspection 17 Install Blades 18 Blade Positions
20. Hi Speed Cotton Stalk Puller Chopper MAN120 Hi Speed Cotton Stalk Puller Chopper Operation 3 Operation Important Information eee eee ee e 26 0157210 REE RS 26 Planting Lines 26 Ground Denseitv 26 TANS DOMAUON nennen Iain spe yes pus 27 Machine Operation 28 allies e EE 28 Lower Hitch Points 28 Upper Hitch Point 28 Attach to Tractor 30 AAJUSEMEIGME sorri a roto etra tta 30 Operate Machine 31 255 29 2015 25 MAN120 Operation Important Information Please read the following information before operating your Hi Speed Cotton Stalk Puller Chopper This information will assist you in getting the most efficient performance from your machine Speed The Hi Speed Cotton Stalk Puller Chopper usually performs best when operated between 6 and 10 MPH Although it works well at slower speeds the percentage of stalks pulled is usually highest when operated in this range This is due in part to the zipper effect that occurs as the stalks are pulled from the ground As the ground speed increases the velocity of the stalks exiting the ground increases The result is increased soil disturbance in all directions Depending on the plant density this disturbance can actually decrease the pulling force required for each plant as well as improve the chopp
21. LL OTHERREPRESENTATIONS TO THE PURCHASER AMADAS specifically excludes any liability on behalf of the company for any incidental or consequential damages including but not limited to crop loss loss of profits rental of substitute equipment or other commercial losses AMADAS shall not be responsible for expenses or inconveniences that you might incur or experience with respect to the AMADAS Stalk Puller Chopper nor shall AMADAS be liable for defects damage or failures caused by improper storage unreasonable use or abuse or accident including the failure to provide reasonable and specified maintenance This warranty applies only to the original purchaser of the equipment Because some states do not allow the exclusion of limitations of incidental or consequential damages the above limitation may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state to state Where there is a conflict between a provision of this warranty and the provision of any state the state legislation prevails AMADA 5 AAA AS FRIES
22. Please note the following about the decals on the following pages Decal locations are also included e Keep them clean and legible Never remove a safety decal from the machine When you replace a part with a safety decal also replace that decal MAN120 06 03 15 11 Safety Decals Do not operate this machine until you have read and understood the operator s manual If you do not have a copy of the manual contact your AMADAS dealer Manuals are available for printing at www amadas com 80935 44 DANGER ENTANGLEMENT HAZARD To avoid Serious injury or death e Operate this machine only when all shields and guards are securely in place 80941 06 03 15 Hi Speed Cotton Stalk Puller Chopper Keepall shields in place Stop engine and remove key before leaving operator s seat to adjust lubricate clean unclog or perform other work on the machine Wait for all motion to stop before servicing this machine Keep hands feet and clothing away from moving parts Keep off equipment unless seat or platform for operation is provided Keep all persons off of machine Make certain everyone is clear of machine before starting engine 80936 MAN120 Hi Speed Cotton Stalk Puller Chopper Safety Decal Locations 808471 8343 aen INSIDE SHIELD INSIDE SHIELD MAN120 06 03 15 Safety Hi Speed Cotton Stalk Puller Chopper NOTES 14 06
23. THIS IS A SERIOUS EVENT THAT MUST BE TREATED BY MEDICAL PROFESSIONALS MAN120 Hi Speed Cotton Stalk Puller Chopper Safety NOTE This section covers general safety Some items may not apply to this type of machine Handle Fuel Safety Avoid Fires Work in Ventilated Area Engine exhaust fumes can cause sickness or death e fitis necessary to run an engine in an enclosed area remove the exhaust fumes from the area with an exhaust pipe extension If you do not have an exhaust pipe extension open the doors and get outside air into the area AMADAS DOES NOT RECOMMEND RUNNING ANY ENGINE IN AN ENLCOSED AREA EVEN WITH VENTILATION Prepare for Emergencies Be prepared if a fire starts Keep a first aid kit and fire extinguisher handy Keep emergency numbers for doctors ambulance service hospital and fire department near your telephone MAN120 06 03 15 Handle fuel with care it is highly flammable Do NOT refuel the machine while smoking or when near open flame or sparks Always stop engine before refueling machine Fill fuel tank outdoors Prevent fires by keeping machine clean of accumulated trash grease and debris Always clean up spilled fuel QS Wear Protective Clothing Wear close fitting clothing and safety equipment appropriate to the job Operating equipment safely requires the full attention of the operator Do NOT wear radio or music headphones while operating machine
24. ate tires Remove valves from valve stems Remove all four lug bolts from each wheel Remove wheels Replace valves in valve stems Reinflate tires to approximately 5 PSI Store indoors out of direct sunlight for maximum life Prepare Tanks Prepare tanks for storage by preventing the water from freezing by one of the following Drain all water from the tanks The upper tank drain plug is shown in the photo For the rotor remove the fill plug and rotate the rotor until the plug is pointing toward ground A gt K n Se Opus m he d 1 Upper tank drain plug _ net si 6 3 2015 91 Maintenance Add anti freeze to water Refer to back of anti freeze bottle for proper mixture for your region Generally a 50 solution should be more than adequate For the SPC 4 model the capacity of the rotor is 66 gallons the weight tank holds 87 The SPC 6 s tanks hold 1 5 as much as the SPC 4 MAN120 Maintenance General Cleaning 1 Remove the wheels and reinstall lug bolts into hubs Remove the shields covering the double universals 3 Remove the shields covering the upper and lower chains MAN120 92 Hi Speed Cotton Stalk Puller Chopper Open all other shields Using pressurized air blow entire machine to remove all dirt debris Once majority of debris is removed by air using a low pressure water hose or indirect water pressure clean machine IMPORTANT If
25. haft mounted 18 diameter turf tires rotate against each other to grip and hold the stalks while the forward motion of the tractor pulls the root systems out of the ground Chopping System Eight drum mounted double beveled replaceable hardened steel blades per row provide linear rotary cutting action Total number of blades 32 SPC 4 48 SPC 6 06 03 15 V Introduction Frame he machine is made up of heavy duty welded box construction with a 6 x 10 main frame Drive System The entire drive system is ground driven using heavy duty 80 chain drives gear boxes and telescoping drive lines With the pulling wheels driven off of the chopping rotor the proper wheel speed is assured regardless of ground speed Drive train safety is provided by a bi directional ratchet clutch MAN120 Introduction Specifications Number of Rows Row Widths Recommended Speed Range Tractor Reguirements Tractor Recommendation Overall Length Overall Width Overall Height Number of Blades Shipping Weight approx Operating Weight approx Drum Diameter MAN120 Hi Speed Cotton Stalk Puller Chopper 36 38 40 6 12 MPH 6 12 MPH Standard CAT III or CAT IVN Standard CAT III or CAT IVN 3 Point or Quick hitch 3 Point or Quick hitch Minimum 160 HP tractor Minimum 190 HP tractor geared to operate at 10 geared to operate at 10 MPH MPH 133 159 194 232 598 68 58 68 5
26. her flammable materials Pressurized lines can accidentally burst when heat goes beyond the immediate flame area MAN120 06 03 15 o Allow any fumes to disperse for at least 15 minutes before welding or heating Do NOT use a chlorinated solvent in areas where welding will take place Do all work in an area that is well ventilated to carry toxic fumes and dust away Dispose of paint coatings and solvent Keep Riders off of Machine Only allow the operator on the machine Riders obstruct the operator s view which results in the machine being operated in an unsafe manner Riders are subject to injury such as being thrown off of the machine Children should NEVER be allowed on the machine Safety Hi Speed Cotton Stalk Puller Chopper NOTE This section covers general safety Some items may not apply to this type of machine Dispose Of Waste Properly e Inquire about the proper way to recycle or Improperly disposing of waste can threaten the dispose of waste from your local environment and ecology Potentially harmful environmental or recycling center FEMA waste includes items such as oil fuel coolant or from your AMADAS dealer brake fluid filters and batteries e Use leak proof containers when draining fluids Do NOT use food or beverage containers that may mislead someone into drinking from them Do NOT pour waste onto the ground down a drain or into a water source Support Machine Properly Service Dri
27. ification All Obligations of AMADAS under this warranty are terminated if the Stalk Puller Chopper is modified or altered in ways not approved by AMADAS D Securing Warranty Service To secure warranty service the purchaser must 1 report the product defect and request repair within the applicable warranty period 2 present evidence of the date of delivery of the Stalk Puller Chopper and 3 make the Stalk Puller Chopper available to an AMADAS authorized dealer within a reasonable period of time E No Dealer Warranty Theselling dealer makes no warranty of his own on any item warranted by AMADAS and makes no warranty on other items The dealer has no authority to make any representation or promise on behalf of AMADAS orto modify the terms or limitations of this warranty in any way F What are your Responsibilities a Read the operator s manual before operating the equipment b Perform all necessary maintenance as described in the operator s manual c Deliver the machine to an AMADAS authorized dealer at your expense during normal working hours for any needed warranty services d Contact an AMADAS authorized dealer promptly on any claim for warranty service e Sign the AMADAS machinery delivery form which will be given to you by the dealer G Disclaimer Thereare no warranties that extend beyond the description here ANY WARRANTIES OF MERCHANTA BILITY AND FITNESS FOR ANY PARTICULAR PURPOSE ARE SPECIFICALLY DISCLAIMED AS ARE A
28. ing action of the machine in hard soil conditions We do NOT recommend running at speeds in excess of 10 MPH in most conditions At very high speeds many operators have difficulty keeping the pulling wheels in line with the rows If the operator veers too far off of the row centers the cotton stalks will pass beside the pulling wheels rather than through them This results in stalks that are cut off near the base rather than pulled out of the soil along with their roots Regrowth can occur under this condition MAN120 Hi Speed Cotton Stalk Puller Chopper Planting Lines The four row Cotton Stalk Puller Chopper SPC 4 works best when operated in fields planted with 4 8 or 12 row planters In fields planted with 6 row planters you have the problem of 2 odd rows to be picked Typically a high percentage of stalks in the odd rows will be chopped off near the base of the plant but will not be pulled due to row spacing inaccuracies between the two sets of odd rows One solution to this problem is to make a pass to pick up just the two odd rows before doing another four row pass We recommend you avoid running the machine in a way that creates odd rows The six row Cotton Stalk Puller Chopper SPC 6 works best with 6 or 12 row planters Ground Density The SPC performs best when the ground is neither extremely wet nor dry In wet soil conditions the ground can actually be so soft that the chopping blades push the stalk do
29. it back as far as possible 4 Remove the four bolts securing the rotor to the frame NOTE If you are moving the rotor more than two holes also remove the idler and chain 3 Remove two shield bolts holding chain drive shield MAN120 38 5 29 2015 Hi Speed Cotton Stalk Puller Chopper Adjust the Rotor o 5 29 2015 Start the tractor and raise the machine slightly to minimize the weight of the machine on the bearings Make sure the weight is not totally off of the bearings Move the tractor straight forward or backwards by inches until the hole in the bearing lines up with the desired hole in the frame Pull forward or backward NUUS OO as necessary E Put a bolt in the hole and install the nut Do NOT tighten Pull forward slightly with the tractor so that the bearings are set to the back of the slot 39 g 10 15 Re tension the chain Adjustments Lower the machine so that the full weight of the machine is on the rotor On the opposite side of the machine put the bolt and nut in but do NOT tighten It may be necessary to inch the tractor forward or backward to line up the holes Install the remaining two bolts Tighten the four bolts Replace the chain and idler if removed If the rotor has been moved all the way forward it may be necessary to shorten the chain several links Replace all shields 4 WARNING Replace all shields before operating your machine
30. ld Move or install blades on rotor to correct row width Replace clutch T CAUTION Complete all instructions for changing row width and replace all shields before attempting to use the machine Slide new shaft into place Tighten set screw MAN120 44 5 29 2015 Hi Speed Cotton Stalk Puller Chopper Maintenance 5 Maintenance E lag ee 46 Gear BOXSS ett eeben 46 Change Ea 46 Cheek Oss 46 PO SHAS a a 46 BN TE 46 Double Universal 47 E a 47 Ge TERT 47 Moo 47 A gorau cea kana edad 47 Ho EE 47 Rotor e le EE 48 E 48 BIES DEREN RU T 49 Lubrication Schedule 50 End of Season Storage 51 Remove Wheels eese 51 Prepare Tarsus ai 51 General Cleaning 52 6 3 2015 45 MAN120 Maintenance Hi Speed Cotton Stalk Puller Chopper Maintenance Gear Boxes Change Oil e After initial 50 Use a standard 90 hours weight non foaming e Every 500 hours oil with EP additives and fill to the bottom of fill plug see photo Beginning of season Every 50 hours visually inspect daily for oil leaks End of season after cleaning PTO Shafts Lubricate points Beginning of Use a standard multi season purpose grease Daily every 10 hours End of season after cleaning MAN120 46 6 3 2015 Hi Speed Cotton Stalk Puller Chopper Maintenance Double Universals Lubricate 2 grease points per universal
31. ller still in the ground it can cause substantial side loading on the lower bearing housings This can break the lower bearing housings 315 29 2015 31 MAN120 Operation Hi Speed Cotton Stalk Puller Chopper NOTES MAN120 32 5 29 2015 Hi Speed Cotton Stalk Puller Chopper Adjustments 4 Adjustment S Weight Addition sirenita 34 farei lu e gE 35 MEST 36 Rotor Distance from Pulling Wheels 37 Adjust the Rotor annen 38 Chan TL Le aars 40 Change Row Width 41 5 29 2015 33 MAN120 Adjustments Hi Speed Cotton Stalk Puller Chopper Weight Addition The amount of weight reguired by the SPC depends on the type of soil soil hardness and the size of the cotton stalks Generally we recommend starting out with the rotor filled and the upper tank empty Adjust the weight under the following conditions IMPORTANT Before adding water determine how much anti freeze needs to be added to the tank Use the chart on the back of the anti freeze bottle to figure the amount needed based on your weather conditions Generally a 50 mixture will be more than adequate for most regions For the SPC 4 the upper tank holds 87 gallons of water the rotor tank holds 66 gallons The tanks of the SPC 6 hold 1 5 times as much as the SPC 4 If you choose not to use anti freeze it is imperative that you drain all water from the tank before the temperature reaches freezing If the water f
32. n death or serious injury This signal word is to be limited to the most extreme situations typically for machine components that for functional purposes cannot be guarded AWARNING Indicates a potentially hazardous situation that if not avoided could result in death or serious injury and includes hazards that are exposed when guards are removed It may also be used to alert against unsafe practices ACAUTION Indicates a potentially hazardous situation that if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices MAN120 Hi Speed Cotton Stalk Puller Chopper Safety NOTE This section covers general safety Some items may not apply to this type of machine Safety Practices Transport Machine Safely Comply with state and local laws Be familiar with tractor operations and follow all safety instructions in the tractor s manual Before moving away always check immediate vicinity e g for children NEVER exceed a maximum speed of 20 MPH Always adapt ground speed to road or field conditions making sure you have adeguate control of steering and stopping Avoid sharp turns holes ditches and obstructions which may cause the tractor to tip particularly on hillsides Avoid Electrical Power Lines MAN120 Make sure all components are secured in the proper position before transporting machine for example basket bin lip extension mower deck
33. r large cotton stalk diameters ordinary hose to add the water sunbaked soils Use an 22 6 3 15 Hi Speed Cotton Stalk Puller Chopper IMPORTANT Before adding water determine how much anti freeze needs to be added to the tank Use the chart on the back of the anti freeze bottle to figure the amount needed based on your weather conditions Generally a 50 mixture will be more than adequate for most regions For the SPC 4 the upper tank holds 87 gallons of water the rotor tank holds 66 gallons The SPC 6 tanks hold 1 5 times as much water If you choose not to use anti freeze it is imperative that you drain all water from the tank before the temperature reaches freezing If the water freezes serious damage will result to the tanks from the expansion of the frozen water MAN120 Hi Speed Cotton Stalk Puller Chopper Preparation Dirt Shield Kit Optional A dirt shield kit is available for purchase from your dealer This kit is used only to keep wheel wells clean and will not affect the performance of your machine Generally the dirt shield kit will have been installed at the factory lf you will be installing this kit yourself refer to the following instructions and the sketch For each wheel Remove the wheel Install the snap ring onto the shatt Slide the metal disk onto the shaft Bolt the wheel back in place Hepeat for each axle MAN120 6 3 15 23 Preparation NOTES 24 6 3 15
34. reezes serious damage will result to the tanks from the expansion of the frozen water He Then the soil is very add more weight by baked the cotton stalk filling the upper tank is large the machine is check condition of pulling stalks out blades if worn replace of the ground but Check soil conditions if not chopping too wet wait for dryer them conditions Check rotor engagement lengthen top link if rotor needs to pe lower MAN120 34 5 29 2015 Hi Speed Cotton Stalk Puller Chopper Inclination Generally the top link on the three point hitch should be adjusted so that the frame of the machine is parallel to the ground top sketch Keep in mind the following If the cotton stalks are very short or have been standing for a long period and become brittle you may need to shorten the top link until the bottom of the pulling wheels are 2 to 3 above the ground middle sketch This should result in improved performance Take care when shortening the link With the tires lowered the wheels are more likely to hit the ground on uneven terrain Potentially damage to the wheels and or shafts could occur If the link is too long the wheels will be raised up and not be able to grasp shorter stalks bottom sketch 5 29 2015 35 Adjustments 55 Pulling wheels 2 3 above ground gt KD O o JA f DNE MAN120
35. rf tires rotate against one another to grip the stalks while the forward motion of the tractor pulls the stalks and root systems out of the ground and then releases them The rotating blade chopping system at the rear of the machine then cuts the stalks and roots into small pieces The AMADAS Hi Speed Cotton Stalk Puller Chopper is designed to operate at high speeds and handle the toughest stalks The SPC 4 is adjustable for 36 38 or 40 row widths the SPC 6 is adjustable for 36 or 38 rows e E e T E E a m EE q re d LA GR iE SM Fa Ee pra ng 2 DER Pa RI m urn n a kri Eh a 54 2 i CS E F md S 06 03 15 Hi Speed Cotton Stalk Puller Chopper Benefits Your AMADAS Hi Speed Cotton Stalk Puller Chopper will provide you with the following benefits e Increased Residue Clearing Capability Removes and chops cotton stalks and their root systems in a single operation e Enhanced Soil Aeration Double bevel blade design provides deep soil penetration e High Speed Operation With the machine operating within its normal range of 6 10 MPH you can easily cover over 100 acres per day e Low Operating Costs Per acre costs are minimal as removal and chopping processes are completed in one machine pass Features The following are some of the significant features of the AMADAS SPC Hi Speed Cotton Stalk Puller Chopper Pulling System For each row tandem s
36. ring lock collar behind photo sprocket Photo shows both sprocket and lock collar removed 7 Open top cover 8 Remove set screw on clutch yoke 9 Remove the main drive shaft MAN120 42 5 29 2015 Hi Speed Cotton Stalk Puller Chopper Adjustments Change Row Width 12 Remove shield covering both universals 13 Referring to the sketch remove the five bolts on the head unit indicated by the arrows on the sketch The sketch shows the bolt pattern for the SPC 4 The SPC 6 is similar but only has the 36 and 38 holes 38 40 36 38 40 Left universal Right universal facing cotton stalk puller 14 Loosen but don t remove the sixth bolt indicated by double arrows on the sketch and in the bottom photo 5 29 2015 43 MAN120 Adjustments Hi Speed Cotton Stalk Puller Chopper Change Row Width 17 Referring to sketch below move the Tighten bearing lock collar gearbox and head unit to the correct row width position The sketch shows the SPC 4 row widths The SPC 6 is similar but does not have the 40 row spacing Replace and tighten all bolts for head unit Replace shims for gearbox Replace and tighten bolts for gearbox Repeat Steps 13 22 for remaining head units Replace drive lines Make sure all grease fittings line up Replace sprocket Align sprocket using distance measured in otep 4 Replace chain Replace idler Re tension chain Replace shie
37. s 54 Correction Operate machine over four rows then make a pass to pick up odd rows before making another four row pass Wait for rain or irrigate to soften soil Add more weight to the machine by filling the upper tank with water Wait for soil to dry some and ground to harden Reduce weight by letting some of the water out of the machine Shorten the top link of the hitch so that the bottom of the pulling wheels are 2 to 3 above the ground Lengthen top link so that wheels are further off ground Move rotor closer to tractor Move the rotor further away from the tractor Make sure machine is operating over four rows MAN120 Hi Speed Cotton Stalk Puller Chopper Troubleshooting Problem Correction Root is still in the ground but Stalk is slipping through the Inflate tires more do not stalk is chopped pulling wheels exceed 32 PSI Stalk is breaking off Make sure ground is soft enough and enough weight is in tanks Root is in place facing down The blade is catching the Move rotor away from pulling but loose in soil stem before it is pulled from wheels the ground Stalk is slipping through the Inflate tires more do not wheels exceed 32 PSI Tires are too worn to grip Replace tires stalks 555 29 2015 55 MAN120 Troubleshooting Hi Speed Cotton Stalk Puller Chopper NOTES 6 3 15 56 MAN120 ONE YEAR LIMITED WARRANTY For AMADAS INDUSTRIES STALK PULLER CHOPPER A General Provi
38. sions The Warranties described below are provided by AMADAS INDUSTRIES AMADAS through its authorized dealers to the original purchaser of each new AMADAS Stalk Puller Chopper AMADAS will repair or replace at its option any part covered under warranty which is found to be defective in material or workmanship during the applicable period of warranty This warranty is applicable only to the cost of the part replaced or repaired and does not cover labor costs involved in installing the replaced or repaired defective part B What is Warranted All parts of any new AMADAS Stalk Puller Chopper are warranted for 12 months The warranty period will begin when the Stalk Puller Chopper is delivered to the purchaser AMADAS will repair or replace at its option any new part or component under the above warranty if a defect in material or workmanship appears in such part or component and is reported to AMADAS before the expiration of the applicable equipment warranty Used equipment is not warranted by AMADAS unless it is specifically covered by a separate warranty document The above warranties cover only defective material and workmanship The warranties do not cover any depreciation orfailure caused by normal wear lack of proper maintenance or use misuse lack of proper protection during storage or accident The purchaser shall pay all costs of routine maintenance and or replacement of maintenance and wear items C Unapproved Service or Mod
39. using pressure washer do NOT direct water spray at bearings This can damage their seals causing premature failure Spray at low water pressure the cavities in the stalk puller heads until the water discharge from the drain hole is clear Pressure wash the pulling wheels after they are removed Spray all drivelines universal joints and exposed shafts with a lightweight oil 10 Replace all shields before storing machine 6 3 2015 Hi Speed Cotton Stalk Puller Chopper Troubleshooting 6 Troubleshooting 535 29 2015 53 MAN120 Troubleshooting Problem A large number of stalks are being chopped off near the pase but not pulled out Stalks are being pulled out but pushed into the ground instead of chopped Stalks are breaking off before being pulled out Wheels are hitting the ground Stalks are flying over the rotor and not being chopped Stalks are being chopped before they are completely out of the ground 6 3 15 Hi Speed Cotton Stalk Puller Chopper Cause Rows are planted in something other than 4 8 or 12 row planters SPC 4 or 6 or 12 row planters SPC 6 and passes are being made over an odd number of rows Soil is too hard Ground is too soft or soil too wet Cotton stalks may be very short or are very brittle Top link of hitch is too short Rotor is too far from the pulling wheels Rotor is too close to the pulling wheels Stalk is completely missing wheel
40. ve Belts Safely e Always lower the attachment or implement When servicing drive belts always observe to the ground before you work on the these precautions machine If the work requires that the E machine or attachment be lifted provide e Avoid serious injury from hand or arm secure support for them If left in a raised entanglement Never attempt to clean position hydraulically supported devices check or adjust belts while the machine can settle or leak down is running Always shut off the engine set the parking brake and remove the Do NOT support the machine on cinder key blocks hollow tiles or props that may erumble under continuous load Do NOT attempt to clean belts with flammable cleaning solvents Do NOT work under a machine that is supported solely by a jack Follow all safety procedures in this manual for supporting the machine When implements or attachments are used with a machine always follow safety precautions listed in the implement or attachment operator s manual 8 06 03 15 MAN120 Hi Speed Cotton Stalk Puller Chopper Safety NOTE This section covers general safety Some items may not apply to this type of machine Service Tires Safely Explosive separation of a tire and rim parts can cause serious injury or death e Do NOT attempt to mount a tire unless you have the proper equipment and experience to perform the job Always maintain the correct tire pressure Do NOT inflate
41. wn into the ground rather than shear them into pieces In hard dry soil conditions the ground can be so hard that the stalks break off at the base rather then pull out from the ground The best solution in either case is to wait until conditions improve Refer to Chapter 4 Adjustments for guidelines when operating in extreme conditions 26 5 29 2015 Hi Speed Cotton Stalk Puller Chopper Transportation The SPC 4 Cotton Stalk Puller Chopper is 13 3 159 wide The SPC 6 is significantly wider Please be aware of this width when you transport the machine behind your tractor Do NOT exceed 25 MPH when towing your SPC If you have questions about transporting your machinery while it is attached to your tractor please refer to the owner s manual for your tractor Operation NOTE Your SPC was equipped with olow Moving Vehicle symbols at the factory Please make sure these symbols are kept in good condition and that they are cleaned before you transport the machine mmi v Ml Loss Re 275 29 2015 21 MAN120 Operation Hi Speed Cotton Stalk Puller Chopper Machine Operation Hitch AMADAS Hi Speed Cotton Stalk Puller Upper Hitch Point Choppers are compatible with the following There are two hitch links on the upper hitch hitches point as shown in the picture Use as follows CAT III CAT IVN CAT III Hitch After reading the information on this page refer TIN
42. y precautions To prevent injury or death use a tractor equipped with a Rollover Protective System ROPS NEVER exceed the limits of a piece of machinery If its ability to perform a job safely is in question DO NOT TRY TO DO THAT JOB Shields e Certain photographs or illustrations in this manual may show a safety shield removed However NEVER operate this machine without all shields correctly in place If a shield must be removed to make a repair or adjustment replace the shield prior to use Safety Decals e Replace any CAUTION WARNING DANGER or instruction safety decal that is not readable or is missing Do NOT paint over remove or deface any safety sign or warning decals 2 06 03 15 Hi Speed Cotton Stalk Puller Chopper Look for the Safety Alert Symbol The Safety Alert Symbol indicates a potential safety hazard to personnel and that extra precaution must be taken When you see this symbol on the machine remain alert and carefully read the message that follows it ALWAYS follow the recommended precautions and safe operating procedures accompanying this symbol If you have any questions please contact your dealer or the manufacturer Safety Signal Words Used Three safety signal words are used on the machine and in this manual to indicate the degree or level of hazard seriousness These three words are ADANGER Indicates an imminently hazardous situation that if not avoided will result i
43. y pressure Search hoses connections for leaks with a piece of cardboard Take appropriate safety measures to protect hands body and face from high pressure fluids Always wear appropriate safety gear to protect hands body and face from exposure to high pressure fluids Never try to block the flow or search for leaks of high pressure fluids with your hands even if wearing gloves High pressure fluids can penetrate gloves as well as your skin Always avoid direct contact of any high pressure fluid low If an accident occurs respond as follows 06 03 15 o Seek medical treatment immediately Any fluid injected into the skin must be surgically removed within a few hours or gangrene may result o Alert the medical professionals that a fluid injection or high pressure spray injury has occurred o Give information on the type of fluid or spray and time the accident occurred If known include the amount of fluid injected and or the system injection pressure o Surgery will most likely be required so no food or drink for the affected person Doctors unfamiliar with this type of injury should reference a knowledgeable medical source Such information is available in English from Deere amp Company Medical Department in Moline Illinois U S A by calling 1 800 822 8262 or 1 309 748 5636 VERY IMPORTANT Although in some cases there is little or no pain from an injection or high pressure spray accident
Download Pdf Manuals
Related Search