Manual - RayBiotech, Inc.
Contents
1. The Positive Control is a cell culture media sample that serves as a system control to verify that the kit components are working The resulting OD will not be used in any calculations if no positive competition is observed please contact RayBiotech Technical Support The Positive Control may be diluted further if desired but be sure the final concentration of biotinylated Somatostatin is 10 ng ml E Sample Preparation 13 If you wish to perform a 2 fold dilution of your sample proceed to step 6c If you wish to perform a higher dilution of your sample dilute your sample with 1X Assay Diluent B before performing step 6c EXAMPLE to make a 4 fold dilution of sample a Dilute sample 2 fold 62 5 ul of sample 62 5 ul of 1X Assay Diluent B b Perform step 6c 125 ul of working solution Item F 125 ul of sample prepared above The total volume is 250 ul enough for duplicate wells on the microplate It is very important to make sure the final concentration of the biotinylated Somatostatin is 10 ng ml Note Optimal sample dilution factors should be determined empirically however you may contact technical support 888 494 8555 techsupport raybiotech com to obtain recommended dilution factors for serum F Preparation of Wash Buffer and HRP 14 If Item B 20X Wash Concentrate contains visible crystals warm to room temperature and mix gently until dissolved 15 Dilute 20 ml of Wash Buffer Concentrate into deionized or dist2. 4 ft monthatas The first standard Standard Somatostatin 2 vials of Somatostatin Peptide 1 vial is enough 2 3 days at 4 C Peptide Item C to run each standard in duplicate Additional dilutions Do not store Anti Somatostatin moe ea 2 vials of ani Somatosiatin of anti vials of ani Somatosiatin 1 month ato at month ato moe ea Item N 15 ml of 5X concentrated buffer Diluent for both 5X Assay Diluent B Item E standards and samples including serum plasma 1 month at 4 C cell culture media or other sample types Somatostatin 2 vials of A eee eer Somatostatin Peptide 1 2 3 days at padaysatae Item F vial is A eee eer to assay the whole plate y HRP To T 600 ee 800X concentrated HRP conjugated Cel not store and Concentrate ee G ee Cel Positive Control Item M Positive Control Item M Item M 1 1 vial of Positive Control of Positive 1 vial of Positive Control 2 3 re at 2 3 days at4ec TMB One Step Substrate 12 ml of 3 3 5 5 tetramethylbenzidine TMB i Reagent Item H buffer solution Stop Solution Item 1 8 8 mi of 0 2 M sulfuric acid of 0 2 M sulfuric acid laa m Return unused wells to the pouch containing desiccant pack reseal along entire edge Vi NOOR OWOD 8 9 10 11 Vil Additional Materials Required Microplate reader capable of measuring absorbance at 450 nm Precision pipettes to deliver 2 ul to 1 ml volumes Adjustable 1 25 ml p
3. and inhibition of the release of numerous secondary hormones Somatostatin regulates insulin and glucagon Somatostatin is secreted in several locations in the digestive system stomach intestine and delta cells of the pancreas In the stomach somatostatin acts on the acid producing parietal cells via G coupled receptor to reduce secretion Somatostatin also indirectly decreases stomach acid production by preventing the release of other hormones including gastrin secretin and histamine which effectively slows down the digestive process Somatostatin has two active forms produced by alternative cleavage of a single preproprotein one of 14 amino acids the other of 28 amino acids In all vertebrates there exist six different somatostatin genes that have been named SS1 SS2 SS3 SS4 SS5 and SS6 The six different genes along with the five different somatostatin receptors allow somatostatin to possess a large range of functions Humans have only one somatostatin gene SST ll General Description The RayBio Somatostatin Enzyme Immunoassay EIA Kit is an in vitro quantitative assay for detecting Somatostatin peptide based on the competitive enzyme immunoassay principle In this assay a biotinylated Somatostatin peptide is spiked into the samples and standards The samples and standards are then added to the plate where the biotinylated Somatostatin peptide competes with endogenous unlabeled Somatostatin for binding to the anti Somato
4. RayBio Human Mouse Rat Somatostatin Enzyme Immunoassay Kit Catalog EIA SOM EIAM SOM EIAR SOM User Manual Last revised December 1 2015 Caution Extraordinarily useful information enclosed Re RayBiotech 1 ii The protein array pioneer ISO 13485 Certified 3607 Parkway Lane Suite 100 Norcross GA 30092 Tel 1 888 494 8555 Toll Free or 770 729 2992 Fax 770 206 2393 Web www RayBiotech com Email info raybiotech com Table of Contents ease SSSCS di i In oenemionsowin SSSCSCS d Cd m forne Cd ao paot ooo a ao Preparation A Preparation of Plate and Anti Somatostatin Antibody B Preparation of Biotinylated Peptide Item F C Preparation of Standards D Preparation of Positive Control E Preparation of Samples F Preparation of Wash Buffer and HRP Strep vm Assay Procedure lege fix Assay Procedure Summary O Assay Procedure Summary pe Calculation of Results A Typical Data B Sensitivity a See eee C Detection Range D Reproducibility E Assay Diagram x Specifcty OOOO O O Specificity Ce xu Select Publications OO O O Select Publications a Troubleshooting Guide Please read the entire manual carefully before starting your experiment I Introduction Somatostatin also known as growth hormone inhibiting hormone GHIH that regulates the endocrine system and affects neurotransmission and cell proliferation via interaction with G protein coupled somatostatin receptors
5. andard and or thoroughly biotinylated antibody Ensure sufficient incubation time e Too brief incubation times assay procedure step 2 may be done e Inadequate reagent overnight volumes or improper dilution Check pipettes and ensure correct preparation Low signal e Inaccurate pipetting Check pipettes e Air bubbles in wells e Remove bubbles in wells Review the manual for proper wash If using a plate washer ensure that all ports are unobstructed Make fresh wash buffer e Plate is insufficiently washed e Contaminated wash buffer Follow storage recomendations in e Improper storage of the sections IV and V Keep substrate ELISA kit solution protected from light e Stop solution Add stop solution to each well before reading plate RayBio ELISA Kits Over 2 000 ELISA kits available visit www RayBiotech com ELISA Kits html for details This product is for research use only 2015 RayBiotech Inc
6. illed water to yield 400 ml of 1X Wash Buffer 16 Briefly centrifuge the HRP Streptavidin vial Item G before use 17 Dilute the HRP Streptavidin concentrate 800 fold with 1X Assay Diluent B Vill Assay Procedure 1 Keep kit reagents on ice during reagent preparation steps It is recommended that all standards and samples be run at least in duplicate 2 Add 100 ul of Anti Somatostatin Antibody Item N See Reagent Preparation step 3 to each well Incubate for 1 5 hours at room temperature with gentle shaking 1 2 cycle sec You may also incubate overnight at 4 C 3 Discard the solution and wash wells 4 times with 1X Wash Solution Buffer 200 300 ul each Washing may be done with a multichannel pipette or an automated plate washer Complete removal of liquid at each step is essential to good assay performance After the last wash remove any remaining Wash Buffer by aspirating or decanting Invert the plate and blot it against clean paper towels 4 Add 100 ul of each standard see Reagent Preparation Section C Positive Control see Reagent Preparation Section D and sample see Reagent Preparation Section E in appropriate wells Be sure to include a blank well Assay Diluent only Cover wells and incubate for 2 5 hours at room temperature with gentle shaking 1 2 cycles sec overnight or at 4 C 5 Discard the solution and wash 4 times as directed in Step 3 Add 100 ul of prepared HRP Streptavidin solution see Reagent P
7. ipettes for reagent preparation 100 ml and 1 liter graduated cylinders Absorbent paper Distilled or deionized water SigmaPlot software or other software which can perform four parameter logistic regression models Tubes to prepare standard or sample dilutions Orbital shaker Aluminum foil Plastic wrap Reagent Preparation Keep kit reagents on ice during reagent preparation steps A Preparation of Plate and Anti Somatostatin Antibody 1 2 Equilibrate plate to room temperature before opening the sealed pouch Label removable 8 well strips as appropriate for your experiment 5X Assay Diluent B Item E should be diluted 5 fold with deionized or distilled water Briefly centrifuge the anti Somatostatin antibody vial Item N Then add 50 ul of 1X Assay Diluent B to the vial to prepare the antibody concentrate Pipette up and down to mix gently The antibody concentrate should then be diluted 100 fold with 1X Assay Diluent B This is your anti Somatostatin antibody working solution which will be used in step 2 of Assay Procedure Section VIII Note The following steps may be done during the antibody incubation procedure step 2 of Assay Procedure B Preparation of Biotinylated Somatostatin Item F 5 Briefly centrifuge the vial of Biotinylated Somatostatin Item F before use 6 See the image below for proper preparation of Item F Transfer the entire contents of the Item F vial into a tube co
8. ntaining 10 ml of 1X Assay Diluent B This is your Working Stock of Item F Pipette up and down to mix gently The final concentration of biotinylated Somatostatin will be 20 ng ml a Second Dilution of Item F for Standards Add 2 ml of Working Stock Item F to 2 ml of 1X Assay Diluent B The final concentration of biotinylated Somatostatin will be 10 ng ml b Second Dilution of Item F for Positive Control Add 100 ul of Working Stock Item F to 100 ul of the prepared Positive Control Item M See section D for Positive Control preparation The final concentration of biotinylated Somatostatin will be 10 ng ml c Second Dilution of Item F for samples Add 125 ul of Working Stock Item F to 125 ul of prepared sample see section E for sample preparation This is a 2 fold dilution of your sample The final concentration of biotinylated Somatostatin will be 10 ng ml 1 vialis enough to run the Item F whole plate First Dilution Working Stock Item F Add entire vial of Item F to 10 ml Assay Diluent Second Dilution Perform a 2 fold dilution of Working Stock Item F c Sample 125 ul of Working Stock Item F 125 ul Prepared Sample b Positive Control 100 ul of Working Stock Item F 100 ul Prepared Positive Control a Standards 2 ml of Working Stock Item F 2 ml of Assay Diluent Final concentration 10 ng ml C Preparation of Standards 7 Label 6 microtubes with the follo
9. raw the best fit curve through the standard points Percentage absorbance B blank OD Bo blank OD where B OD of sample or standard and Bo OD of zero standard total binding A Typical Data These standard curves are for demonstration only A standard curve must be run with each assay Somatostatin EIA 120 100 ee 80 SA 60 B BO Pa Ye 20 4 has 0 01 0 1 1 10 100 1000 Somatostatin concentration ng ml B Sensitivity The minimum detectable concentrations of Somatostatin is C Detection Range 0 1 1 000 ng ml D Reproducibility Intra Assay CV lt 10 Inter Assay CV lt 15 E Assay Diagram Recommended Plate Layout Bark Total Binding SA2 sa2 sa10 SA3 SAG Key Blank Buffer Only Total Binding Biotin Somatostatin only Standard 1 1000 ng ml Standard 2 100 ng ml Standard 3 10 ng ml Standard 4 1 ng ml Standard 5 100 pg ml Pos Control Biotin with Item M XI Specificity This EIA kit is designed to detect pro Somatostatin not active Somatostatin XIV Select EIA Publications 1 Plum L Lin HV Dutia R Tanaka J Aizawa KS et al The Obesity Susceptibility Gene Carboxypeptidase E Links FoxO1 Signaling in Hypothalamic Pro opiomelanocortin Neurons with Regulation of Food Intake Nature Med 2009 15 10 1195 1201 Ghrelin EIA EIA GHR 1 2 Hug C Lodish HF Visfatin a new adipokine Science 2005 307 5708 366 7 3 Kim MK Crystal s
10. reparation step 7 to each well Incubate for 45 minutes at room temperature with gentle shaking It is recommended that incubation time should not be shorter or longer than 45 minutes Discard the solution and wash 4 times as directed in Step 3 Add 100 ul of TMB One Step Substrate Reagent Item H to each well Incubate for 30 minutes at room temperature in the dark with gentle shaking 1 2 cycles sec Add 50 ul of Stop Solution Item to each well Read at 450 nm immediately Assay Procedure Summary Prepare all reagents samples and standards as instructed Add 100 ul anti Somatostatin to each well Incubate 1 5 hours at room temperature or overnight at 4 C Add 100 ul standard or sample to each well Incubate 2 5 hours at room temperature or overnight at 4 C Add 100 ul prepared Streptavidin solution Incubate 45 minutes at room temperature Add 100 ul TMB One Step Substrate Reagent to each well Incubate 30 minutes at room temperature Add 50 ul Stop Solution to each well Read at 450 nm immediately X Calculation of Results Calculate the mean absorbance for each set of duplicate stands controls and samples and subtract the blank optical density Plot the standard curve using SigmaPlot software or other software which can perform four parameter logistic regression models with standard concentration on the x axis and percentage of absorbance see calculation below on the y axis D
11. statin antibody After a wash step any bound biotinylated Somatostatin then interacts with horseradish peroxidase HRP streptavidin which catalyzes a color development reaction The intensity of the colorimetric signal is directly proportional to the amount of captured biotinylated Somatostatin peptide and inversely proportional to the amount of endogenous Somatostatin in the standard or samples A standard curve of known concentration of Somatostatin peptide can be established and the concentration of Somatostatin peptide in the samples can be calculated accordingly Ill How It Works Y Y ace yi yi Target molecule Biotinylated tt in sample Peptide bed tk gt Capture antibody yi pn is added to the wells Biotin peptide Standard w 5 Sample interact competitivly m_a i for spots on the capture antibodies Y Y BNP EIA Kit a Add HRP Streptavidin and Color Substrate Data Analysis IV Storage The entire kit may be stored at 20 C to 80 C for up to 6 months from the date of shipment For extended storage it is recommended to store at 80 C Avoid repeated freeze thaw cycles For prepared reagent storage see table below V Reagents Size Description Storage Sabiny Stability Somatostatin 96 wells 12 Eaa x 8 wells coated with Geis tae month at aor oe A ereere antibody Wash Buffer ao ft monthatas ao Item B 25 ml 25 mi of 20x concentrated soon 20X concentrated solution 1 month at
12. tructure of visfatin pre B cell colony enhancing factor 1 nicotinamide phosphoribosyltransferase free and in complex with the anti cancer agent FK 866 J Mol Biol 2006 362 1 66 77 4 Revollo J R et al The NAD biosynthesis pathway mediated by nicotinamide phosphoribosyltransferase regulates Sir2 activity in mammalian cells J Biol Chem 2004 279 50754 50763 5 Oh I S Shimizu H Satoh T et al Identification of nesfatin 1 as a satiety molecule in the hypothalamus Nature 2006 443 7112 709 12 6 Zhang J Ren P Avsian Kretchmer O Luo C Rauch R Klein C Hsueh A Obestatin a peptide encoded by the ghrelin gene opposes ghrelin s effects on food intake Science 2005 310 5750 996 9 7 Cummings D Weigle D Frayo R Breen P Ma M Dellinger E Purnell J Plasma ghrelin levels after diet induced weight loss or gastric bypass surgery N Engl J Med 2002 346 21 1623 30 8 Tschop M Smiley DL Heiman ML Ghrelin induces adiposity in rodents Nature 2002 407 6806 908 913 9 Kojima M Hosoda H Date Y Nakazato M Matsuo H Kangawa K Ghrelin is a growth hormone releasing acylated peptide from stomach Nature 1999 402 6762 656 60 XIII Troubleshooting Guide e Check pipettes Poor standard e Inaccurate pipetting Briefly centrifuge Item C and dissolve curve e Improper standard dilution the powder thoroughly by gently mixing Briefly spin down vials before e Improper preparation of opening Dissolve the powder st
13. wing concentrations 1000 ng ml 100 ng ml 10ng ml 1 ng ml 100 pg ml and 0 pg ml Pipette 450 ul of biotinylated Somatostatin Item F working solution prepared in step 6a into each tube except the 1 000 ng ml leave this one empty It is very important to make sure the concentration of biotinylated Somatostatin is 10 ng ml in all standards 8 Briefly centrifuge the vial of Somatostatin Standard Item C Pipette 8 ul of Item C and 792 ul of 10 ng ml biotinylated Somatostatin working solution prepared in step 6a into the tube labeled 1000 ng ml Mix thoroughly This solution serves as the first standard 1 000 ng ml Somatostatin standard 10 ng ml biotinylated Somatostatin 9 To make the 100 ng ml standard pipette 50 ul of the 1000 ng ml Somatostatin standard into the tube labeled 100 ng ml Mix thoroughly 10 Repeat this step with each successive concentration preparing a dilution series as shown in the illustration below Each time use 450 ul of biotinylated Somatostatin and 50 ul of the prior concentration until the 100 pg ml is reached Mix each tube thoroughly before the next transfer ul 50l 50 ul 50 ul AAAA sisiziziziz 1000 100 1 100 0 ng ml ng ml eal ng ml pg ml pg ml D Positive Control Preparation 11 Briefly centrifuge the Positive Control vial Item M 12 Refer to step 6b This is a 2 fold dilution of the Positive Control The final concentration of biotinylated Somatostatin should still be 10 ng ml
Download Pdf Manuals
Related Search