R204GF-E
Contents
1. Receiving signals Receiving signals but ID Do not perform the linking procedure with motor s main wire connected or with the engine operating as it may result in serious injury is unmatched Power On when F S sets it Compliance Information Statement for U S A This device trade name Futaba Corporation of America model number R204GF E complies with part15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesiredoperation The responsible party of this device compliance is Futaba Service Center 3002 N Apollo Drive Suite 1 Champaign IL 61822 U S A TEL 217 398 8970 or E mail support futaba rc com Support FUTABA CORPORATION 1080 Yabutsuka Chosei mura Chosei gun Chiba ken 299 4395 Japan Phone 81 475 32 6982 Facsimile 81 475 32 6983 FUTABA CORPORATION 2011 11 12. and no further linking is necessary unless the receiver is to be used with another transmitter 1 Place the transmitter and the receiver close to each other within half 0 5 meter 2 Turn on the transmitter and the receiver 3 Push and hold the Link switch on the receiver 4 When the link is complete the LED on the receiver changes to solid green AAWARNING After the linking is done please cycle receiver power and check if the receiver to be linked is really under the control by the transmitter to be linked Please refer to the table below for LED status and receiver condition LED Off LED On LED Blink LED Early Blink the first one second R204GF E Specifications S FHSS FHSS system 4 channel receiver e Receiving on 2 4GHz band e System S FHSS FHSS system auto detection At S FHSS Normal High speed mode auto detection e Receiving Range 70m 230ft at the best conditions e Operating voltage Typ 4 8V 7 4V shared with servo e F S and Battery F S function The operation channels differ according to the transmitter used However Battery F S doesn t function when it is used with FHSS and F S becomes only CH2 e Battery F S voltage 3 8V e Current drain 30mA at no signal e Size 1 38x0 91x0 35 35 1x23 2x9mm e Weight 0 210z 6g The Battery F S voltage is set for 4 cell NiCd NiMH battery Battery F S function doesn t work properly when other type battery is used No signal reception
3. work with current Futaba FASST system LED Link switch g Futaba erPcar LED SW R204GF E 4 CHANNEL RECEIVER 474 LBA BAGH 2 1 ss 1 1 Usage condition on High Speed mode A CAUTION When using the high speed mode use a Futaba digital servo including brushless servo Analog servos cannot be used e The use of analog servos may cause servo trouble lt Ch4 output Battery terminal B Ch output 1 to 3 Operating Precautions Once the R204GF E detects the S FHSS normal mode S FHSS high speed mode or FHSS mode the detected mode is locked as long as the power is ON When need to change the mode please cycle power If there are many S FHSS FHSS systems turned on around your receiver it might not link to your transmitter In this case even if the receivers LED stays solid green unfortunately the receiver might have established a link to one of the other transmitters This is very dangerous if you do not notice this situation In order to avoid the problem we strongly recommend you to double check whether your receiver is controlled by your transmitter by giving throttle input etc and then checking servo response Link Procedure Each transmitter has an individually assigned unique ID code In order to start operation the receiver must be linked with the ID code of the transmitter with which it is being paired Once the link is made the ID code is stored in the receiver
4. 1M23N17456 Futaba Thank you for purchasing the R204GF E receiver R204GF E S FHSS FHSS 2 4GHz system Auto Detection For EP Car models Built in antenna 4 channel receiver High Voltage System BIA A WARNING NEVER use dry batteries for the power supply of the R204GF E as they may cause difficulties NEVER use the R204GF E in GP cars The R204GF E is designed for use with the Futaba S FHSS or FHSS system transmitter The S FHSS system has two 2 operation mode as shown below eNormal mode High Speed mode The Normal mode accepts any type of servos or the peripherals as the frame rate of the output is 13 6ms The High Speed mode only accepts the digital servos including BLS series and most peripheral equipments such as the brushless ESCs The frame rate of the outputs is 6 8ms However there is a transmitter that cannot correspond to high speed mode Please pay special attention to the information contained within this manual and transmitter s manual in order to have a pleasant running experience eBuilt in antenna The R204GF E receiver is designed to be used only for EP Car models Due to the special design of the R204GF E we cannot recommend its use in other types of models gas poweredmodels eThe R204GF E is compatible with the S FHSS or FHSS system transmitters Note The R204GF E is compatible with the S FHSS or FHSS system transmitters Futaba S FHSS FHSS system does not
Download Pdf Manuals
Related Search
R204GF E r204gf-e r204gf-t r203gf receiver